fuji frontier 350-370 installation - service manual - parts list
TRANSCRIPT
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
1/222
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
2/222
INTRODUCTION
This manual outlines the maintenance and servicing procedures, electrical diagram and parts list for
the Frontier Manager Printer Controller (referred to as FMPC) for Fujifilm Digital Minilab FRONTIER
350/370/355/375/570.
This manual is a professional publication provided for qualified service personnel or other persons
fully trained in equipment service procedures. All other personnel and operators are restricted from
servicing the FMPC. When maintenance service is needed, be sure to contact qualified service
personnel.
When servicing internal machine parts, make sure the power switch and the main power
supply on the power distribution board are both set to the OFF position.If the main power is left ON, electricity will flow as far as the power switch and power supply
section, and this can cause electric shocks and/or short-circuiting.
If the power is left on, there is also the possibility for the machine to be accidentally activated
causing damage to the machine and/or bodily injury.
The light source section and dryer will be hot to the touch. Wait 15 minutes after turning off
the power before commencing with servicing procedures.
IMPORTANT
IMPORTANT describes improper handling procedures that may adversely affect performance
or damage the equipment.
NOTE:
NOTE designates those items, provisions, and supplementary explanations for which it is
important to maintain methodical concern and consideration relative to operational
procedures.
:
describes additional or useful information.
1. All rights are reserved by the Fuji Photo Film Co., Ltd. (FUJIFILM).
2. Manual usage is restricted to FUJIFILM equipment-related technical and service personnel.
3. This manual contains exclusive information relating to FUJIFILM equipment and is
therefore proprietary. Unauthorized disclosure is prohibited.
4.FUJIFILM’s prior consent is required in regard to the following.
KManual copying in whole or in part.KDisclosure of manual contents to unauthorized personnel.
KManual uses for purposes other than technical service.
Precautions Generally Applying to All Servicing Operations
Service Manual Appropriations
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
3/222
3
CONTENTS
1 Preparations .......................................................................................................................... 10
1.1 Recommended PC, Monitor Switcher, and Extension Cable for Keyboard ....................... 10
1.1.1 Recommended PC................................................................................................. 101.1.2 Recommended Monitor Switcher ........................................................................... 10
1.1.3 Extension Cable for Keyboard................................................................................ 10
1.1.4 SP-3000 Monitor's Power Cable ............................................................................ 10
1.1.5 Ethernet Cable ....................................................................................................... 10
1.2 Checking the Kit Contents ................................................................................................. 11
1.3 Required Tools and CDs ................................................................................................... 13
1.4 Power Souce Specification ................................................................................................ 13
2 Installation for FRONTIER 570 ....................................................................................... 14
2.1 Installation Procedure List ................................................................................................. 14
2.2 PC Preparations ................................................................................................................ 15
2.2.1 IEEE1394 Board Installation .................................................................................. 15
2.2.2 Bios Setup.............................................................................................................. 16
2.2.3 Windows XP Installation and Partitioning............................................................... 16
2.2.4 Setup of Remaining Space in Hard Disk................................................................ 18
2.2.5 Installing Other Driver Software ............................................................................. 21
2.2.6 User Registration.................................................................................................... 21
2.2.7 Windows Settings................................................................................................... 22
2.2.8 NetBEUI Setup....................................................................................................... 28
2.3 IEEE1394 Driver Pre-installation ....................................................................................... 29
2.4 Copying Print Size Table from SP to FD ........................................................................... 30
2.5 Creating Backup FD for SP-3000 and LP5700 .................................................................. 30
2.6 Changing Mode from SP-3000 to FMPC ........................................................................... 31
2.7 Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher ................................... 31
2.8 Turning on LP5700 ............................................................................................................ 35
2.9 Turning on FMPC and Installing LP5700 Driver ................................................................ 36
2.10 Installing SP-3000 Driver ................................................................................................... 37
2.11 Disabling Network Connection on SP Side ....................................................................... 38
2.12 Installing FMPC Software [D20] ........................................................................................ 39
2.13 Copying SP-3000 Print Size Table to FMPC ..................................................................... 40
2.14 Installing DI Print/Data Writing Software [C4/C5] Client in FMPC ..................................... 40
2.15 Turning on Imaging Controller ........................................................................................... 41
2.16 Input/Output Device Setup for FMPC ................................................................................ 41
2.17 Timer Setup in FMPC ........................................................................................................ 42
2.18 Installation Information Setup in FMPC ............................................................................. 43
2.19 Paper Condition Setup ...................................................................................................... 43
2.20 FMPC Output Device Setting in Imaging Controller .......................................................... 44
2.21 Operational Check ............................................................................................................. 45
2.22 Creating Backup FD for FMPC/SP-3000 ........................................................................... 50
2.23 System Shutdown .............................................................................................................. 50
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
4/222
4
3 Installation for FRONTIER 355/375 ............................................................................... 51
3.1 Installation Procedure List ................................................................................................. 51
3.2 PC Preparations ................................................................................................................ 533.3 Disabling of “Rack Auto Cleaning” ..................................................................................... 53
3.4 Creating Backup FD for SP-3000 and LP1500/2000 ......................................................... 54
3.5 Replacing the ROM for Printer .......................................................................................... 55
3.6 Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher ................................... 56
3.7 Turning on FMPC .............................................................................................................. 60
3.8 Disabling Network Connection on SP Side ....................................................................... 60
3.9 IEEE1394 Driver Installation in SP .................................................................................... 60
3.10 [A1] Stand-alone Version-up and DI Print/Data Writing Software Installation in SP .......... 61
3.11 IEEE1394 Driver Pre-installation ....................................................................................... 63
3.12 Installing IEEE1394 Driver for SP in FMPC ....................................................................... 643.13 Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000) .......................... 65
3.14 Installing IEEE1394 Driver for LP in FMPC ....................................................................... 65
3.15 FMPC [D20] Installation (Reinstall) with Printer’s Backup FD ........................................... 66
3.16 DI Print/Data Writing Software [C4/C5] Client Installation in FMPC .................................. 69
3.17 Installation Information Setup for FMPC ............................................................................ 70
3.18 Output Device Setup for SP and Restarting SP ................................................................ 70
3.19 Copying Print Size Table to FD then Copying SP-3000 Print Size Table to FMPC .......... 71
3.20 FMPC Output Device Setting in Imaging Controller .......................................................... 72
3.21 Enabling of “Rack Auto Cleaning” ..................................................................................... 73
3.22 Paper Condition Setup ...................................................................................................... 73
3.23 Creating Backup FD for FMPC, SP-3000 and LP1500/2000 ............................................ 74
3.24 Operational Check ............................................................................................................. 75
3.25 System Shutdown .............................................................................................................. 75
4 Installation for FRONTIER 350/370 ............................................................................... 76
4.1 Installation Procedure List ................................................................................................. 76
4.2 PC Preparations ................................................................................................................ 78
4.3 Disabling of “Rack Auto Cleaning” ..................................................................................... 78
4.4 Creating Backup FD for SP1500/2000, LP1500/2000 ....................................................... 79
4.5 Replacing the ROM for Printer .......................................................................................... 80
4.6 Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher ................................... 81
4.7 Turning on FMPC .............................................................................................................. 85
4.8 Disabling Network Connection on SP Side ....................................................................... 86
4.9 [A1] Stand-alone Upgrade in SP [Ver.1.5 -> Ver.1.7] and
DI Print/Data Writing Software [C4/C5] Client Installation in SP ....................................... 87
4.10 IEEE1394 Driver Pre-installation ....................................................................................... 89
4.11 Installing IEEE1394 Driver for SP in FMPC ....................................................................... 90
4.12 Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000) .......................... 90
4.13 Installing IEEE1394 Driver for LP in FMPC ....................................................................... 91
4.14 FMPC [D20] Software Installation (Reinstall) with Printer's Backup FD ............................ 92
4.15 DI Print/Data Writing Software [C4/C5] Client Installation in FMPC .................................. 95
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
5/222
5
4.16 Installation Information Setup for FMPC ............................................................................ 96
4.17 Output Device Setup for SP and Restarting SP ................................................................ 97
4.18 Copying Print Size Table to FD then Copying LP1500/2000 Print Size Table to FMPC ... 984.19 FMPC Output Device Setting in Imaging Controller .......................................................... 99
4.20 Enabling of “Rack Auto Cleaning” ..................................................................................... 99
4.21 Paper Condition Setup ...................................................................................................... 99
4.22 Creating Backup FD for FMPC, SP1500/2000 and LP1500/2000 ..................................... 100
4.23 Operational Check ............................................................................................................. 101
4.24 System Shutdown .............................................................................................................. 101
5 Maintenance Menu (FRONTIER 350/370/355/375) .................................................. 102
5.1 Operational Procedure ...................................................................................................... 102
5.2 System Operation Setup and Check (41) .......................................................................... 1035.2.1 Production Information 1 (411)............................................................................... 103
5.2.2 Production Information 2 (412)............................................................................... 104
5.2.3 Accumulated Production Information (413)............................................................ 105
5.2.4 Timer Setup (414) ................................................................................................. 106
5.2.5 Error Information Check (415)............................................................................... 107
5.2.6 Installation Information Confirmation (416) ............................................................ 108
5.2.7 Data Backup (417) ................................................................................................. 108
5.2.8 Clear Error Log (41E)............................................................................................. 109
5.2.9 Installation Information Setup (41F) ....................................................................... 110
5.2.10 DI Manager Administrative Setting (41l)................................................................. 110
5.3 Print Condition Setup and Check (42) ............................................................................... 111
5.3.1 Paper Condition Setup ........................................................................................... 111
5.3.2 Processing Solution Temperature Check............................................................... 113
5.3.3 Control Strip Processing......................................................................................... 113
5.3.4 Print Size Setup (424) ............................................................................................ 116
5.3.5 Paper Condition Method Setup (42J)..................................................................... 117
5.3.6 Back Print Setup (42O) .......................................................................................... 117
5.4 Printer Adjustment/Maintenance (45) ................................................................................ 118
5.4.1 Paper Magazine Registration (451)........................................................................ 118
5.4.2 Paper Feed Length Adjustment (452) .................................................................... 120
5.4.3 Test Pattern Printing (453) ..................................................................................... 121
5.4.4 G, B Laser (SHG) Optimal Temperature Setup (454) ............................................ 122
5.4.5 Paper Feed (455) ................................................................................................... 123
5.4.6 Printer Temperature Display (456)......................................................................... 123
5.4.7 Printer Input Check (457) ....................................................................................... 124
5.4.8 Image Position Fine Adjustment (458) ................................................................... 124
5.4.9 Printer I/O Check (45A).......................................................................................... 125
5.4.10 Printer Function Select (45B) ................................................................................. 126
5.4.11 Laser Exposure Check (45C) ................................................................................. 127
5.4.12 R Laser (R-LD) Data (45D) .................................................................................... 127
5.4.13 G Laser (G-SHG) Data (45E) ................................................................................. 128
5.4.14 B Laser (B-SHG) Data (45F).................................................................................. 128
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
6/222
6
5.4.15 Scanning Position/Scanning Home Position Parameter Setup (45G).................... 129
5.4.16 Main Scanning Position Adjustment/Laser Beam Sync. Rough
Adjustment (45H) ................................................................................................... 1295.4.17 Laser Beam Sync. Fine Adjustment Print (45J) ..................................................... 131
5.4.18 Laser History Display (45K).................................................................................... 132
5.4.19 Paper Condition Setup Table (LUT) Copy (45L) .................................................... 132
5.4.20 Printer Mechanism Fine Adjustment (45M)............................................................ 133
5.4.21 Back Printer Test (45N).......................................................................................... 134
5.4.22 Printer Operation Data Display (45P)..................................................................... 134
5.4.23 Data Saving (45T) .................................................................................................. 135
5.4.24 Data Download (45U)............................................................................................. 135
5.4.25 Precut Length Setting (45V)................................................................................... 136
5.5 Processor Adjustment/Maintenance (46) .......................................................................... 1375.5.1 Replenisher Pump Output Measurement............................................................... 137
5.5.2 Auto-cleaning Pump Output Measurement ............................................................ 138
5.5.3 Processing Temperature Setting (463) .................................................................. 141
5.5.4 Replenisher Rate Setup (464)................................................................................ 141
5.5.5 Evaporation Correction Rate Setting (465) ............................................................ 142
5.5.6 Low Volume Setting (466)...................................................................................... 142
5.5.7 Processor Temperature Calibration (467).............................................................. 143
5.5.8 Processor Input Check (468).................................................................................. 144
5.5.9 Processor I/O Check (46A) .................................................................................... 145
5.5.10 Processor Operating Condition Setup (46B) .......................................................... 1465.5.11 Processor Operation Data Display (46C)............................................................... 146
5.5.12 Processor Operation Data Display 2 (46E) ............................................................ 147
5.6 Special Operations (48) ..................................................................................................... 148
5.6.1 Paint (48A) ............................................................................................................. 148
5.6.2 Explorer (48B) ........................................................................................................ 148
5.6.3 Command (48C)..................................................................................................... 149
6 Maintenance Menu (FRONTIER 570) ........................................................................... 150
6.1 Operational Procedure ...................................................................................................... 150
6.2 System Operation Setup and Check (1) ............................................................................ 151
6.2.1 Production Information 1 (411)............................................................................... 151
6.2.2 Production Information 2 (412)............................................................................... 152
6.2.3 Accumulated Production Information (413)............................................................ 154
6.2.4 Timer Setup (414) .................................................................................................. 155
6.2.5 Error Information Check (415)................................................................................ 156
6.2.6 Installation Information Reference (416) ................................................................ 157
6.2.7 Data Backup (417) ................................................................................................. 157
6.2.8 Clear Error Log (41E)............................................................................................. 158
6.2.9 Installation Information Setup (41F) ....................................................................... 159
6.2.10 DI Manager Administrative Setting (41I) ................................................................ 159
6.3 Print Condition Setup and Check (2) ................................................................................. 160
6.3.1 Paper Condition Setup (421).................................................................................. 160
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
7/222
7
6.3.2 Print Size Setup (424) ............................................................................................ 162
6.3.3 Paper Condition Method Setup (42J)..................................................................... 163
6.3.4 Back Printing Setup (42O)...................................................................................... 1646.3.5 Paper Surfaces Display Setup (42R) ..................................................................... 165
6.4 Printer Adjustment/Maintenance (5) .................................................................................. 166
6.4.1 Paper Magazine Registration (451)........................................................................ 166
6.4.2 Paper Magazine Feeding Fine Adjustment (452)................................................... 168
6.4.3 Test Pattern Printing (453) ..................................................................................... 169
6.4.4 G Laser (SHG) Optimal Temperature Setup (454)................................................. 171
6.4.5 Paper Feed (455) ................................................................................................... 172
6.4.6 Printer Temperature Display (456)......................................................................... 172
6.4.7 Printer Input Check (457) ....................................................................................... 173
6.4.8 Image Position and Tilt Fine Adjustment (458) ...................................................... 1736.4.9 Printer I/O Check (45A).......................................................................................... 174
6.4.10 Printer Function Select (45B) ................................................................................. 175
6.4.11 Laser Exposure Check (45C) ................................................................................. 176
6.4.12 R Laser (R-LD) Data (45D) .................................................................................... 177
6.4.13 G Laser (G-SHG) Data (45E) ................................................................................. 177
6.4.14 B Laser (B-LD) Data (45F) ..................................................................................... 178
6.4.15 Scan/Scan Home Position Parameter (45G).......................................................... 178
6.4.16 Main Scan/Laser Beam Sync. Rough Adjustment (45H) ....................................... 179
6.4.17 Laser Beam Sync. Fine Adjustment Print (45J) ..................................................... 180
6.4.18 Laser History Display (45K).................................................................................... 1816.4.19 Paper Condition Setup Table (LUT) Copy (45L) .................................................... 182
6.4.20 Printer Mechanical Fine Adjustment (45M) ............................................................ 182
6.4.21 Printer Operation Data Display (45P)..................................................................... 183
6.4.22 Data Saving (45T) .................................................................................................. 183
6.4.23 Data Download (45U)............................................................................................. 184
6.4.24 Filter Replacement History (45a)............................................................................ 184
6.4.25 Feeding Position Sensor Fine Adjustment (45b).................................................... 185
6.4.26 Image Position Initial Setting (45c)......................................................................... 186
6.4.27 Sub-scan Feeding Speed Adjustment (45d) .......................................................... 187
6.4.28 Sub-scanning Soft Nip Fine Adjustment (45e) ....................................................... 187
6.4.29 Sensor Calibration (Initial) (45f).............................................................................. 188
6.4.30 Sensor Calibration (Daily) (45g)............................................................................. 189
6.5 Processor Adjustment/Maintenance (6) ............................................................................ 190
6.5.1 Replenisher Pump Output Measurement/Setting (461) ......................................... 190
6.5.2 Auto Cleaning Output Measurement/Setting (462) ................................................ 192
6.5.3 Processing Temperature Setting (463) .................................................................. 194
6.5.4 Low Volume Processing Setup (466)..................................................................... 195
6.5.5 Processor Temperature Calibration (467).............................................................. 195
6.5.6 Processor Input Check (468).................................................................................. 197
6.5.7 Processor I/O Check (46A) .................................................................................... 197
6.5.8 Processor Operating Condition Setup (46B).......................................................... 198
6.5.9 Processor Operation Data Display (46C)............................................................... 199
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
8/222
8
6.5.10 PS Liquid Concentration Management (46G) ........................................................ 199
6.6 Option Adjustment / Maintenance (7) ................................................................................ 200
6.6.1 COM Port Setting (47A) ......................................................................................... 2006.7 Special Operations (9) ....................................................................................................... 201
6.7.1 Paint (49A) ............................................................................................................. 201
6.7.2 Explorer (49B) ........................................................................................................ 201
6.7.3 Command (49C)..................................................................................................... 202
7 Error Messages and Countermeasures ..................................................................... 203
7.1 Error Indication Rule .......................................................................................................... 203
7.1.1 Message Number ................................................................................................... 203
7.1.2 Message Icons ....................................................................................................... 203
7.1.3 X-#### Actions....................................................................................................... 2037.2 Messages .......................................................................................................................... 204
8 Measures against FMPC Failures ................................................................................. 212
8.1 To Return to Direct-connecting Type in FRONTIER 350/370 ........................................... 212
8.2 To Return to Direct-connecting Type in FRONTIER 355/375 ........................................... 215
9 Index ......................................................................................................................................... 218
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
9/222
9
■ How to Read This Manual
(1) Chapter ContentsThis manual consists of the following chapters.
Chapter1 Preparations
Describes the devices, tools and power source required for installation.
Chapter2 Installation for FRONTIER 570
Describes the installing procedures for the FMPC for FRONTIER 570.
Chapter3 Installation for FRONTIER 355/375
Describes the installing procedures for the FMPC for FRONTIER 355/375.
Chapter4 Installation for FRONTIER 350/370
Describes the installing procedures for the FMPC for FRONTIER 350/370.
Chapter5 Maintenance Menu (FRONTIER 350/370/355/375)
Describes the maintenance menu (“Setup and Maintenance”) for the FMPC for FRONTIER 350/
370/355/375.
Chapter6 Maintenance Menu (FRONTIER570)
Describes the maintenance menu (“Setup and Maintenance”) for the FMPC for FRONTIER 570.
Chapter7 Error Messages and Countermeasures
Lists up the FMPC error messages and their countermeasures.
Chapter8 Measures against FMPC failuresDescribes how to connect SP to LP directly when the FMPC malfunctions.
Chapter9 Index
(2) Abbreviation for Devices
The abbreviation of devices at the upper right-hand of
the page (in the Chapter Title bar) shows where the
current installing operation is done.
The following abbreviations are used.
• Frontier Manager Printer Controller: FMPC • Imaging Controller: IC
• FRONTIER Scanner: SP
• FRONTIER Printer: LP
• FRONTIER 350/370: F350/370
• FRONTIER 355/375: F355/375
• FRONTIER 570: F570
• FRONTIER 350/370/355/375/570: F350/370/355/375/570
(3) Notation for Screen/Button Name
• Screen name is enclosed within “ ”.
• Button name is enclosed within [ ] parentheses.
• Items on the screen is enclosed within [ ] parentheses.
Abbriviation
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
10/222
10
1 Preparations
1.1.1 Recommended PC
• Model : Dell Optiplex GX280 (No monitor)
• Main Body : Small Mini Tower
• CPU : Pentium-4 2.8GHz/800FSB (FSB800MHz)
• Chip Set : IntelR 915G Express
IntelR Hyper-Threading Function disabled
• Memory : 1GB/DDR2 SDRAM 400MHz
• HDD : Serial ATA 80GB/7200rpm
• Network : IntelR Pro/1000MT(10/100/1000) for interface
• I/O Devices : 3.5˝ FDD, CD-ROM, Built-in Audio-speaker
• OS : WindowsR XP Professional SP1/SP2
• PCI Bus : More than 3 (for IEEE1394 x 2 and 2nd Serial Adapter Card)
• Dimension : (Width x Height x Depth) : 181 x 447 x 426 mm
IMPORTANT :
• To supply the power source to the FMP, make sure to use the power source cable, sharing the grounding with the
printer as much as possible, so that the voltage deviation between the FMPC and printer does not occur.
• Install the FMPC so shat their cables are not tightened. For example, if the 1394 board is loosened by pulling the cable,
the communication error may occur.
1.1.2 Recommended Monitor Switcher
• CPU Auto-Switcher
• PC: IBM PC/AT
• Keyboard : PS/2 Keyboard
• Mouse : PS/2 Mouse
• Monitor : HD(3WAY)/Multi-scan display with 15pin connector
• OS : WindowsR XP, WindowsR 2000, WindowsR NT
• Method : Electric Control by pressing the select switches or pressing [Ctrl] key twice quickly (hot-key
switching)/ Auto-scanning
1.1.3 Extension Cable for Keyboard
• Extension cable for keyboard : KB-KYE2 (2m)
• Supported keyboard : General keyboard (Mini-DIN 6pin-type)
1.1.4 SP-3000 Monitor's Power Cable
1.1.5 Ethernet Cable
1.1 Recommended PC, Monitor Switcher, and Extension Cable for Keyboard
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
11/222
11
Check the kit contents.
[FMPC Kit]
1.2 Checking the Kit Contents
Part Name Part No. Shape and Identification
1 FMP Controller Kit 899C21583A2
2 FMPC Software 899C21583A4
IEEE1394 Board x 2 ROM (for CTL CB)
FMP Controller [D20]
CD Ver.2.0-0E-101
IEEE1394 Cable (4.5m) x 1
Instruction Manual
Installation/
Service Manual/
Parts List
F350/370
System Software [A1]
Ver.7.7-0E-201
F355/375/570 System
Software [A1] CD
Ver.1.7-0E-105
F355/375/570
Driver Disk
Custom Button
Setting Tools CD
Blank FD for
Backup (3)
FMP Controller
Driver Disk
Operator QuickReference Guide
FMP Controller [D20]
CD Ver.2.0-0E-101
F350/370
System Software [A1]
Ver.7.7-0E-201
F355/375/570 System
Software [A1] CD
Ver.1.7-0E-105
F355/375/570
Driver Disk
Custom Button
Setting Tools CD
FMP Controller
Driver Disk
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
12/222
12
[Each Part]
Part Name Part No. Shape and Identification
1 IEEE 1394 Board 113C898440
2 ROM(for CTL CB) 114C898435
3 IEEE 1394 Cable
(4.5m)
136C898441
4 FMP Controller
[D20] CDVer.2.0-0E-101
114C6006886E00
5 F355/375/570
System Software
[A1] CD
Ver.1.7-0E-105
114C2159701E03
6 FRONTIER 350/
370 System
Software [A1] CD
Ver.7.7-E
114C6006883E01
7 F350/370 SystemSoftware [A1] CD
Ver.7.7-0E-201
—
8 Installation/Service
Manual/Parts List
—
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
13/222
13
• ROM remover or screw driver (-)
• Windows XP Professional SP1/SP2 CD
• DI Print/Data Writing Service Software [C4/C5] CD
• Insulating tape
• Print Size Set Tool Software (FD)• “3KPrintsizeCopyTool” Software (FD)
(used only in case of FRONTIER 355/375)
Make sure that the AC power at the installation location is correct by checking the rated label of the PC.
Part Name Part No. Shape and Identification
9 Operator Quick
Reference Guide
—
10 Custom Button
Setting Tools CD
114C2159702E00
11 1394 Driver Disk for
SP-3000
114C2159703X00
12 1394 Driver Disk for
FMPC
114C6006884X00
13 Blank FD for
Backup CD
114C1062675(FMPC)
114C1062676(SP)
114C1058873(LP)
1.3 Required Tools and CDs
1.4 Power Souce Specification
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
14/222
14
2 Installation for FRONTIER 570
Install the FMPC devices and software, and set them up for use.
Install the FMPC using the following procedure.
FMPC = Frontier Manager Printer Controller
SP = Scanner
LP = Printer
IC = Imaging Controller
2.1 Installation Procedure List
No. Procedures Location Refer to
1 IEEE1394 Board Installation FMPC See Section 2.2.1 on page 15
2 PC Preparations FMPC See Section 2.2 on page 15
3 IEEE1394 Driver Pre-installation FMPC See Section 2.3 on page 29
4 Copying Print Size Table from SP to FD SP See Section 2.4 on page 30
5 Creating Backup FD for SP-3000 and LP5700 SP See Section 2.5 on page 30
6 Changing Mode from SP-3000 to FMPC SP See Section 2.6 on page 31
7 Connecting FMPC, FRONTIER, LAN cable
and Monitor Switcher
SP, FMPC, LP, Monitor Switcher See Section 2.7 on page 31
8 Turning on LP5700 LP See Section 2.8 on page 35
9 Turning on FMPC and Installing LP5700
Driver
FMPC See Section 2.9 on page 36
10 Installing SP-3000 Driver FMPC See Section 2.10 on page 37
11 Disabling Network Connection on SP Side FMPC See Section 2.11 on page 38
12 Installing FMPC Software [D20] FMPC See Section 2.12 on page 39
13 Copying SP-3000 Print Size Table to FMPC FMPC See Section 2.13 on page 40
14 Installing DI Print/Data Writing Software
[C4/C5] Client in FMPC
FMPC See Section 2.14 on page 40
15 Turning on Imaging Controller IC See Section 2.15 on page 41
16 Input/Output Device Setup for FMPC FMPC See Section 2.16 on page 41
17 Timer Setup in FMPC FMPC See Section 2.17 on page 42
18 Installation Information Setup in FMPC FMPC See Section 2.18 on page 43
19 Paper Condition Setup FMPC/LP See Section 2.19 on page 43
20 FMPC Output Device Setting in Imaging
Controller
IC See Section 2.20 on page 44
21 Operational Check FMPC,SP, LP, IC, MonitorSwitcher See Section 2.21 on page 45
22 Creating Backup FD for FMPC/SP-3000 FMPC, SP See Section 2.22 on page 50
23 System Shutdown SP, FMPC, IC See Section 2.23 on page 50
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
15/222
15
2.2.1 IEEE1394 Board Installation
Install the two 1394 boards in the FMPC.
1 While pressing the two buttons on each side,open the upper cover slowly.
2Lift up the board stopper while pressing thehook.
3 Remove the second and third dummy coversfrom the left in the board section.
4 Insert the 1394 board into the slot that is the thirdfrom the left, then pressing it on slowly, and then
confirm that it is securely installed in the slot.
5 In the same way, install another 1394 board inthe slot that is the second from the left.
2.2 PC Preparations
Upper Cover
Buttons (2)NMP001
Board Stopper
HookNMP002
Dummy Covers (2)
NMP003
1394 Board
NMP004
1394 Board
NMP005
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
16/222
16
6 Lower the stopper until the click sounds tosecure the boards.
7 Close the upper cover.
2.2.2 Bios Setup
Start up the FMPC, then press the [F2] key justwhen “Strike F1 to retry boot, F2 for setup utility”.
Make sure that “Hyper - threading” is set to
“Disabled”.
If [Hyper-Threading] is changed to “Enabled”, the
Windows must be installed again.
2.2.3 Windows XP Installation and
Partitioning
Install the Windows XP Professional in the FMPC
PC, then set up the partition.
It is not necessary to install it when using a PC with
Windows XP Professional already installed.
[Procedures]
1 Insert the Windows XP Professional installer CDinto the CD drive.
Board Stopper
NMP006
Upper Cover
NMP007
NMP012
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
17/222
17
2 Set up the PC again.
3 When the message “Press any key to boot fromCD” appears, press the [Enter] key.
4 When the message “Windows XP LicensingAgreement” appears, press the [F8] key if you
agree to the terms of the license.
5 When the message “The following list shows theexisting partitions and unpartitioned space on
this computer” appears, press the [D] key to
delete all existing partition(s).
6 When the message “The partition you tried todelete is a system partition” appears, press the
[Enter] key, then the [L] key.
7 After all partitions are deleted, select[Unpartitioned space], then press the [C] key.
8 Set “10000MB” for the partition size, and pressthe [Enter] key.
9 Select the above “10000MB” partition, and pressthe [Enter] key.
10 Format this partition with NTFS.
NMP010
Press any key to boot from CD.
Windows XP Licensing Agreement
Microsoft Windows XP Professional.Microsoft (r) Windows (r) XP Tablet PC Edition andMicrosoft (r) Windows (r) XP Media Center EditonEND-USER LICENSE AGREEMENT
IMPORTANT-READ CAREFULLY : This End-UserLicense Agreement (“EULA”) is a legal agreement between you(either an individual or a single legal entity) and themanufacturer (“Manufacturer”) of the computer system orcomputer system component (“HARDWARE”) with which you acquiredthe Microsoft software product (s) identified on theCertificate of Authenticity (“COA”) affixed to the HARDWARE oron the associated product documentation (“SOFTWARE”). TheSOFTWARE includes Microsoft computer software, and may includeassociated media, printed materials, “online” or electronicdocumentation, and Internet based ser vices. Note, however,that any software, documentation, or web services that areincluded in the SOFTWARE, or accessible via the SOFTWARE, andare accompanied by their own license agreements or terms ofuse are governed by such agreements rather than this EULA.The terms of printed paper EULA, which may accompany the
Windows XP Professional Setup
The following list shows the existing partitions andunpartitioned space on this computer.
Use the UP and DOWN ARROW key to select an item in the list.
• To set up Windows XP on the selected item, press ENTER.
• To create a partition in the unpartitioned space, press C.
• To delete the selected partition, press D.
76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR]
C: Partition 1 [New (Raw)] 10001 MB ( 10001 MB free)Unpartitioned space 66292 MB
Windows XP Professional Setup
The following list shows the existing partitions andunpartitioned space on this computer.
Use the UP and DOWN ARROW keys to select an item in the list.
• To set up Windows XP on the selected item, press ENTER.
• To create a partition in the unpartitioned space, press C.
• To delete the selected partition, press D.
76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR]
Unpartitioned space 76293 MB
Windows XP Professional Setup
You asked Setup to create a new partition on76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR].
• To create the new partition, enter a size below and
press ENTER.
• To go back to the previous screen without creatingthe partition, press ESC.
The minimum size for the new partition is 8 megabytes (MB).The maximum size for the new partition is 76285 megabytes (MB).Create partition of size (in MB): 100000
Windows XP Professional Setup
The following list shows the existing partitions andunpartitioned space on this computer.
Use the UP and DOWN ARROW keys to select an item in the list.
• To set up Windows XP on the selected item, press ENTER.
• To create a partition in the unpartitioned space, press C.
• To delete the selected partition, press D.
76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR]
C: Par tition1 [New (Raw)] 1001 M B (10 001 MB free)
Unpartit ioned space 66292 MB
Windows XP Professional Setup
The partition you selected is no t formatted. Setup will nowformat the partition.
Use the UP and DOWN ARROW key to select the file systemyou want, and then press ENTER.
If you want to select a different par tition for Windows XP,press ESC.
Format the partition using the NIFS file system (quick)Format the partition using the FAT file system (quick)Format the partition using the NIFS file systemFormat the partition using the FAT file system
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
18/222
18
11 After the format is completed, the PC isautomatically restarted.
12 After the restart, DO NOT press any key until thewizard screen appears even if “Press any key to
boot from CD” is displayed.
13 While following the Wizard instructions, complete[Regional and Language Options], [Personalize
Your Software], [Computer Name and
Administrator Password] and [Date and
Settings].
14 After the system is restarted, Windows XPDesktop screen appears.
15 Restart the PC, and change the drive readingorder at the start-up to [1. Diskette Drive] -
[2. Hard-disk Drive C:] - [3. IDE CD-ROM Device]
(For procedures, See “2.2.2 Bios Setup” on page
16.).
2.2.4 Setup of Remaining Space in Hard
Disk
Set up the remaining space in the hard disk.
1 On the Desktop, select [Start] - [Control Panel] -[Administrative Tool] - [Computer Management]
to display the “Computer Management” screen.
2 Right-click on the unallocated area, then select[New Partition].
3On the “Welcome to New...” screen, click the[Next] button.
Windows XP Professional Setup
This portion of Setup has completed successfully.
If there is a floppy disk in dr ive A:, remove it.
To restart your computer, press ENTER.When your computer restarts. Setup will continue.
Your computer will reboot in 2 secons....
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
19/222
19
4 On the “New Partition Wizard” screen, select[Extended partition], then click the [Next] button.
5 Click the [Next] button.
6 Click the [Finish] button.
7 In the same area on the “ComputerManagement” screen, right-click, then select
[New Logical Drive].
8 On the “Welcome to New...” screen, click the[Next] button.
9 On the “Select Partition Type” screen, select[Logical drive], then click the [Next] button.
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
20/222
20
10 Click the [Next] button.
11 Specify “D” for [Assign the following...], then clickthe [Next] button.
12 Select [NTFS] for “File system”, then click the[Next] button.
13 Formatting is started.
14 After formatting is completed, check if “NewVolume” is “Healthy”.
15 Right-click on the CD drive, then select [ChangeDrive Letter and Paths].
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
21/222
21
16 Select “N”, and then click the [OK] button.
17 Click the [X] button to close the opened screens.
2.2.5 Installing Other Driver Software
Install other driver software provided in the DELL
setup CD. (For details, see “Instruction Manual” for
DELL PC.)
2.2.6 User Registration
Register the following user name and password.
The following procedures are an example when
using the Wizard.
1 On the Desktop, select [Start] - [Control Panel] -
[User Accounts], then on the “User Accounts”screen, click [Create a new account], then [Apply
Options] button, then enter “FRONTIER” and
then click the [Next] button.
2 Select “Computer administrator”, then click the[Create Account] button.
USER NAME: FRONTIER
PASSWORD: FRONTIER
GROUP: Administrator
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
22/222
22
3 On the “User Accounts” screen, click [Changethe way users log on or off], then enter
“FRONTIER” both in the “Type a new password”
and “Type a new password again...”, then click
the [Create Password] button.
4 Open the “Control Panel” screen, then click[Switch to Classic View].
5 Click the [User Account] button, then click[Change the way users log on or off], and then
on the “Select logon and logoff options” screen,
remove the checkmark [✓] from “Use theWelcome screen”, then click the [Apply options]
button.
2.2.7 Windows Settings
Set up the Windows functions.
Log on with the user name “FRONTIER”, then start
settings.
(1) Disabling of Windows XP Style
1 After the system is restarted, right-click on anypart of the Desktop, then open the [Display
Properties] screen, and then select [Windows
Classic] for [Theme].
2 On the Desktop, select [Start] - [Run], then onthe “Run” screen, enter “Services.msc”, then
click the [OK] button.
3 On the “Service” screen, double-click [Themes].
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
23/222
23
4 On the “Themes Properties (Local Computer)”screen, select “Disabled” for [Startup type], then
click the [Stop], then [OK] button.
(2) Password History Setting
1 On the Desktop, select [Start] - [Control Panel] -[Administrative Tools] - [Local Security Policy] to
open the “Local Security Settings” screen.
2 Select [Password Policy] - [Enforce passwordhistory], then in the “Enforce password history
Properties” dialog, select “0” for [Password
remembered], then click the [Apply], then [OK]
button.
(3) Long Date Format Setting
1Double-click the [Regional and LanguageOptions] on the “Control Panel” screen, then on
the “Regional Options” tab screen, click the
[Customize] button to set a long date format,
then click the [Apply] - [OK] buttons.
(4) System Error Setting
1 On the Desktop, select [Start] - [Control Panel] -[System], then on the “System Properties”
screen, click [Advanced] tab, then click the
[Settings] button for [Startup and Recovery], then
set up as shown below.
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
24/222
24
2 After the above items are set, click the [OK]button.
(5) Disabling of User Assistant Function
1 On the Desktop, select [Start] - [Control Panel] -[Accessibility Options], then in the “Settings for
StickyKeys” dialog, click the [Settings] for
[StickyKeys], then remove all checkmarks [✓],
then click the [OK] button.
2 In the “Settings for StickyKeys” dialog, click the[Settings] for [FilterKeys], then remove all check
marks [✓], then click the [OK] button.
3 In the “Settings for StickyKeys” dialog, click the[Settings] for [ToggleKeys], then remove the
checkmark [✓] in the “Use shortcut”, then click
the [OK] button.
[✔] : Write an event to the system log
[✔] : Send an administrative alert
[ ] : Automatically restart
“Complete memory dump” for [Write debugging information]
“D:\MEMORY.DMP” for [Dump file]
[✔] : Overwrite any existing file
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
25/222
25
4 Click the [OK] button to close the “Settings forStickyKeys” dialog.
(6) Non-display Setting of Screen Keyboard
Dialog Box
1 On the Desktop, select [Start] - [All Programs] -[Accessories] - [Accessibility] - [On-screen
Keyboard].
2 Add the checkmark [✓] to “On-Screen Keyboard”dialog, then click the [OK] button.
(7) Disabling of Error Reporting
1 On the Desktop, select [Start] - [Control Panel] -[System], then on the “System Properties”
screen, click [Advanced] tab, then click the [Error
Reporting] button.
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
26/222
26
2 Select “Disable error reporting”, then remove thecheckmark [✓] from “But notify me....”, then click
the [OK] button.
(8) Non-display Setting for Taskbar
3 On the Desktop, select [Start] - [Control Panel] -[Taskbar and Start Menu], add the checkmark
[✓] to “Auto-hide the taskbar”, then click the [OK]
button.
(9) Screen Resolution
1Right-click on any part of the Desktop, then onthe “Settings” tab screen of the “Display
Properties” screen, select more than “800 by 600
pixels” for “Screen area”, then more than 24 bit
(True Color) for “Colors”, then click the [Apply] -
[OK] buttons.
(10) Non-display Setting of Screen Saver
1 Right-click on any part of the Desktop, then onthe “Screen Saver” tab screen of the “Display
Properties” screen, set “None” for “Screen
saver”, then click the [Apply] - [OK] buttons.
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
27/222
27
(11) Disabling of Power Standby
1Double-click the [Power Options] on the “ControlPanel” screen, then on the “Power Options
Properties” tab screen, select “Never” for “Turn
off monitor”, “Turn off hard disks” and “System
standby”, then click the [Apply] - [OK] buttons.
(12) Disabling of Auto Update
1 On the Desktop, select “Control Panel” -“System” - “Automatic Updates”, then remove
the checkmark [✓] from “Keep my computer up
to date. ........”, then click the [Apply] - [OK]
buttons.
(13) Disabling of Desktop Cleanup
1Right-click on any part of the Desktop, then
select “Desktop” tab - “Customize desktop”, then
remove the checkmark [✓] from "Desktop
cleanup", then click the [OK] button.
(14) “Visual Notification” to ON in Dr.
Watson Dialog Box
1 On the Desktop, select [Start] - [Run], then enter“Drwtsn32” and then click the [OK] button.
In the “Dr. Watson for Windows” dialog box, add
the checkmark [✓] to “Visual Notification” in
“Options”.
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
28/222
28
(15) Non-display Setting of Internet
Explorer Dialog Box
1 Select [Control Panel] - [Internet Options] -[Security] tab, then click the [Custom Level...],
then select [Miscellaneous] - [Submit
nonencrypted form data], then select “Enable”.
When using the Service Pack2 (SP2), also set up
the following two items.
(16) Disabling the Windows Fire Wall
1 Open the [Control Panel].
2 Double-click the [Windows Fire Wall].
3 Select [Off], then click the [OK] button.
(17) Disabling the Security Center
1 On the Desktop screen, select [Start] -> [Run],then enter “service.msc”, and then click the [OK]
button.
2 Double-click the [Security Center] to open theproperties screen, then select [Disabled] for
[Startup type], and then click the [Stop] button.
3 Click the [Apply], then [OK] button.
2.2.8 NetBEUI Setup
Set up the NetBEUI protocol in the FMPC.
[Required Files]
To set up the NetBEUI, the following files stored in
the Windows XP installer CD are required.
CD Drive\Valueadd\Msft\Net\Netbeui
They are to be copied in the following folders in the
HD of the FMPC.
NOTE:
Make all files and their extensions visible by using
[Tools]/[FolderOptions] before hand.
[Procedures]
1Right-click on the [My Network] icon to open the“My Network Properties” screen.
2 Copy “Netnbf.inf” and “nbf.sys” in the CD to anyfolder in the hard disk.
3 Open the “Local Area Connection Properties”.
4 Click the [Install] button.
File Name Target Folder
1 Netnbf.inf C:\windows\inf
2 nbf.sys C:\windows\system32\drivers
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
29/222
29
5 Select [Protocol], then click the [Add] button. 6 Select [NetBEUI Protocol], then click the [OK]button.
7 Make sure that the [NetBEUI Protocol] is addedin the list.
8 This completes the NetBEUI seup.
1 Insert the FMPC driver CD into the CD-ROM,then in the “Device Drivers Disk [D-01]” dialog
box, click the [OK] button. This completes the
FMPC driver disk setup.
2 When the FMPC driver disk setup is completednormally, the “Device Drivers Disk [D-02]” dialog
box appears. Remove the driver disk from the
CD-ROM drive, then click the [OK] button to shut
down the system. After shutdown, turn on the
FMPC.
2.3 IEEE1394 Driver Pre-installation
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
30/222
30
Copy the print size table from SP to FD by using the
dedicated print size copy tool.
1 Insert the print size copy tool FD into the FDdrive of SP-3000, open the Explorer, then
execute “PrintSizeTool.exe” in FD.
2 When the FRONTIER model and System [A1] isproper, the following message appears. Click the
[OK] button to start copying it to the system.
3 After copying, the following message appears.
Create a backup FD for SP-3000 and LP5700 in
SP.
[Selection]
“4 Setup and Maintenance” - ”1 System Operation
and Check” - ”7 Data Backup”
1 Prepare a new floppy disk for data backup whenbacking up data.
NOTE:
A floppy disk is unnecessary for pricing unit data
backup because data is backed up to the hard disk
of the main control unit.
2 Insert the floppy disk into the floppy drive of themain control unit.
3 Move the cursor to the “Destination” box andselect “Film Scanner”, “Printer Processor” or
“Pricing Unit”.
NOTE:
Perform the data backup for the pricing unit when
pricing unit data is changed. Data is backed up
from the pricing unit to the hard disk of the main
control unit. If the data backup is not performed,
changed pricing unit data is canceled when starting
up the system next time.
4Click the [OK] button.
• The “Making the backup of the data” message
appears.
5 Upon completion of the backup, click the[Cancel] button.
• Operation returns to the menu screen.
6Remove the floppy disk from the drive.
2.4 Copying Print Size Table from SP to FD
2.5 Creating Backup FD for SP-3000 and LP5700
SP
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
31/222
31
In SP, change the mode from SP-3000 to FMP
Controller, then shut down the SP through the post-
operational checks.
[Selection]
“4 Setup and Maintenance” - ”1 System Operation
Setup and Check” - ”F Installation Information
Setup”
1 Change the output device from “LP-5700” to“FMP Controller”.
2 Click the [OK] button.
• Operation returns to the menu screen.
3 Perform the post-operational checks to shutdown the system and then restart the system.
• The new settings are activated.
Connect the SP-3000, FMPC, LP5700, LAN cableand the monitor switcher.
(1) IEEE1394 Cable Preparation
Bind the bared part of the existing IEEE1394 cable
connected between the printer (LP) and scanner
(SP).
1 Disconnect the IEEE1394 cable from thescanner(SP).
2Remove the clamp from the cable.
3 Bind the bared part of the cable with insulatingtape.
2.6 Changing Mode from SP-3000 to FMPC
2.7 Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher
MP047
Clamp
InsulatingTape
IEEE1394 Cable
MP006
SP LPFMPCSP /
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
32/222
32
(2) IEEE1394 Cable Connection Preparations
Connect the IEEE1394 cable from the LP to the connector in right-hand board, then connect the cable fromthe SP to the one in the left-hand board.
IMPORTANT
Do not connect the two cables to the same board in the FMPC.
IMPORTANT
Make sure that the IEEE1394 cable from scanner (SP) is connected to the lower board, and the cable from printer
(LP) to the upper board.
Printer (LP)
ExistingIEEE1394 Cable (10m)
IEEE1394 Cable
(4.5m)
Scanner (SP)
FMPCSP LP
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
33/222
33
(3) Monitor Switcher Connections
Connect the FMPC, monitor switcher, and FRONTIER as follows.
It is recommended that the monitor switcher be installed on the main control unit.
By placing the full keyboard as shown above, you can press the [Ctrl] key easily to switch the display.
MP046
FMPCSP LP
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
34/222
34
(4) Other Connections
Connect the FMPC, FRONTIER and the monitor switcher and then connect the LAN cable from the HUB towhich the Imaging Controller is connected as shown in the following connection diagram.
To Imaging Controller
5
3
1
4
2
1
3
4
HUB
FRONTIER (SP)
Monitor Switcher
(Front)
(Back)
Main Control Unit (SP)FMPC
Power Supply
Keyboard
Mouse
IMPORTANT
Connect the
monitor’s power
cable to the power
supply directly.
Do not connect thescanner’s power
connector.
FMPCSP LP
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
35/222
35
Turn on the LP5700.
2.8 Turning on LP5700
L2987
LP
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
36/222
36
Set the driver CD in the CD drive, then turn on the
FMPC. Then log on with following user name and
password.
After the start-up, the “Found New Hardware
Wizard” screen appears. Follow the screen
instructions to complete the driver installation.
1 On the “Found New Hardware Wizard” screen,click the [Next] button.
2On the “Completing the Found...” screen, clickthe [Finish] button. This completes the
installation of the driver for LP5700 normally.
2.9 Turning on FMPC and Installing LP5700 Driver
NMP010
User Name: FRONTIER
Password: FRONTIER
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
37/222
37
In FMPC, run and complete “VDEntry” to install the
SP-3000 driver.
1 On the Desktop, select [Start] - [Run], then enter“VDEntry” and then click the [OK] button.
2 In the “VirtualDriverEntry” dialog box, click the[Regist.] button.
3 After the registration, the following dialog boxappears. Click the [OK] button to complete the
VDEntry.
4On the “Welcome to the Found...” screen, clickthe [Next] button.
5 When the “Completing the Found New...” screenappears, click the [Finish] button. This completes
the SP-3000 driver installation.
2.10 Installing SP-3000 Driver
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
38/222
38
Disable the 1394 network connection on SP side.
1 Disconnect the IEEE1394 cable (for connectingto LP5700) from the FMPC.
2 Select [Start] - [Control Panel], then click the[Network Connections].
IMPORTANT
Check the settings are done as follows:
1394 Connection on SP: Disabled
1394 Connection on LP: Enabled
3 Right-click on the 1394 Connection whose statusis “Enabled”, then set it to “Disabled”.
4 Connect the IEEE1394 cable (for connecting tothe LP5700) to the FMPC again.
5 Shut down the FMPC from [Start] - [ShutDown...]
2.11 Disabling Network Connection on SP Side
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
39/222
39
1Start up the FMPC, the log on to the FMPC PCwith the user “FRONTIER” and with the
password “FRONTIER”, then insert the installer
CD into the CD drive. The installer is
automatically started up. If the installer is not
stared up, select the executable file
“N:\Setup.exe” in the CD drive directly.
2 Procedure Selection [A-001]On the “Procedure Selection [A-001]” screen,
select “New Installation”, then click the [Next]
button to start installation.
3 Starting New Installation [A-010]
[Yes]: Starts the new installation.
[No]: Returns to the “Procedure Selection [A-
001]” screen.
4Copying of files in CD to HDD is started up.
5 In the “New Installation Completion [A-020]”dialog box, click the [OK] button.
6 In the “Setup Completion [A-030]” dialog box,remove the FMPC installer CD from the CD
drive, then click the [OK] button to complete the
installation.
IMPORTANT
The “Setup Completion (A-030)” dialog box
prompts you to install the DI Print/Data Writing
Service [C4/C5] successively, but here click the
[OK] button to close the installation, because the
print size table must be copied first.
2.12 Installing FMPC Software [D20]
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
40/222
40
Copy the SP-3000 print size table that was copied
to the FD in “2.4 Copying Print Size Table from SP
to FD”, to the FMPC.
1 Insert the print size copy tool FD in which thesizes are stored in “2.4”, and then open the
“Explorer”, then double-click
“PrintSizeSetTool.exe” in FD drive.
When the connections are properly done, the
following message appears. To star t copying,
click the [OK] button.
2Another confirmation message appears. Clickthe [OK] button to start copying.
3 Data is copied from the FD to FMPC.
4When copying is completed, the following
message appears.
5 Remove the FD from the FD drive.
1 Insert the DI Print/Data Writing Software [C4/C5]installer CD into the CD drive of the FMPC, then
start the installation.
2 Remove the [C4/C5] installer CD from the CDdrive, then restart the FMPC PC.
2.13 Copying SP-3000 Print Size Table to FMPC
2.14 Installing DI Print/Data Writing Software [C4/C5] Client in FMPC
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
41/222
41
Turn on the Imaging Controller.
On the “[41F] Installation Information Setup” screen in “Setup and Maintenance”, set “SP-3000 (V1.7-)” to
[Input Device], then “LP5700” to [Output Device], then shut down the FMPC PC through the “Post-operational
Check”, then start it up again.
2.15 Turning on Imaging Controller
2.16 Input/Output Device Setup for FMPC
C4C509
FMPCIC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
42/222
42
Perform the “[414] Timer Setup” in “Setup and
Maintenance” in the FMPC.
NOTE:
The timer ON date/time of the scanner cannot be set.
1 To update “Present time setup”, change the dateand time, and click [OK] button.
NOTE:
To cancel the update, press the [Cancel] button.
2 To change the timer On date and time, check theday of the week and enter the time in the “Timer
ON Date/Time Setting” box.
3 Set the preheat timer by follow the steps below, ifnecessary.
IMPORTANT
The ON time for a night-time preheating
operation mist not overlap with the ON time of
the weekly timer since night-time preheating
takes priority and shuts down all power when it is
set OFF.
If, for instance, the calendar time is set to 5:00
AM and night-time preheating is turned ON at
3:30 AM, all the power will be shut down two
hours later at 5:30 AM.
NOTE:
Night-time preheating is usually conducted when
the room temperature drops below 10°C (50°F) at
night and the temperature is not controlled for 8 or
more hours.
1) Select “YES” for “Preheat setting”.
• The 1st and 2nd preheat setting boxes
appear.
2) Move the cursor to “1st Preheat” and enter the
time.
3) Move the cursor to “2nd Preheat” and enter
the time.
NOTE:
For preheating only once, set the same time for
both the first and second times.
• Select “NO” when no preheat timer is used.
• The second preheating timer is ignored if
the first and second time overlap.
1st. preheat time: 2:00 AM
2nd. Preheat time: 3:00 AM
With the above settings, nighttime preheating will
occur from 2:00 AM to 4:00 AM (2 hours).
4 Click the [OK] button.
• Operation returns to the menu screen.
2.17 Timer Setup in FMPC
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
43/222
43
Perform “[41F] Installation Information Setup” in
“Setup and Maintenance” in the FMPC.
1 Enter the same Delivery Date and Startup Dateas the dates set in “[0140] Installation
Information Setup” in the SP-3000.
2Click the [OK] button.
3 On the confirmation dialog box, click the [OK}button.
4 After the setup, shut down the FMPC PC throughthe “Post-operational Check”, then start it up
again.
NOTE:
Make sure to restart the FMPC.
Perform “[421] Paper Condition Setup” in “Setup and Maintenance” in the FMPC.
IMPORTANT
Make sure to perform the paper condition setup for all paper to be used.
2.18 Installation Information Setup in FMPC
2.19 Paper Condition Setup
FMPC SP
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
44/222
44
Register the FMPC output device in the Imaging Controller.
■ Setup Example is DI Print/Data Writing [C4/C5]
[Selection]
“Print Service - Administration” - ”Output Device” Set up “sRGBFMPC” and “PDFMPC” for [Device].
IMPORTANT
Installing of DI Import/Export Driver Software [C2} must be required.
The default device names for “FMPC” are “sRGBFMPC” and “PDFMPC”.
2.20 FMPC Output Device Setting in Imaging Controller
IC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
45/222
45
Perform the film printing in the FRONTIER, then the
DSC printing from Imaging Controller to check the
operation.
(1) Printing from Imaging Controller
[Imaging Controller Operation]
1 Set the media in the drive.
2In the [OUTPUT] field, select the FRONTIER
device.
3In the [INPUT] field, click the icon of the mediayou inserted.
4 On the DSC Print Service screen, select thefolder in which the images are stored.
5 Select the images to be printed.
6 Click the [Set] button. The image files are listed
2.21 Operational Check
FD121
Click the [Set] button.
Click the icon of the media you inserted.
Select the folder.
Select the images.
IC FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
46/222
46
up in the [Order Specification Column].
7 The ”Confirmation” dialog appears.
8 Remove the media from the drive.
9 Click the [OK] button.
10 Registering of order is completed.
[FMPC Operation]
11 On the Main Menu screen, select [2 Print], thenclick the [OK] button.
12 In the [Next Print] list on the “Print Status Notice”screen, the DI order with the status “Printing” is
displayed, and then it is printed.
13After the printing is completed, the order is
Click the [Set] button.
FD124
Click.
IC FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
47/222
47
moved to the [Done] list.
[Sheets being processed] on the lower right-hand
side of the screen shows where the current order is
being processed.
14 After the printing is completed, click the [NextOrder Stop] button.
15 Click the [Main Menu] button.
16 Control returns to the “Main Menu” screen.
(2) Printing from FRONTIER
If the [Resume] button appears at the bottom of the
screen, click it to switch to the [Next Order Stop]
button. Then printing is started.
• The images of the first 6 frames appear on thescreen.
SP FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
48/222
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
49/222
49
IMPORTANT
The orders that are registered in the FMPC
cannot be deleted with the [Print Stop] key. Todelete them, select orders one by one, then click
the [Cancel] button on the printing status screen.
[FMPC Operation]
3 Press the button of the switcher to display theFMPC main menu screen.
Also by pressing the [Ctrl] key twice quickly, the
display can be switched between FRONTIER and
FMPC.
4 On the Main Menu screen, select [2 Print], thenclick the [OK] button.
5 In the [Next Print] list on the “Print Status Notice”screen, the film order with the status “Printing” is
displayed, and then it is printed.
6After the printing is completed, the order ismoved to the [Done] list.
[Sheets being processed] on the lower right-hand
side of the screen shows where the current order is
being processed.
MP019
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
50/222
50
7 After the printing is completed, click the [NextOrder Stop] button.
8 Click the [Main Menu] button.
9 Control returns to the “Main Menu” screen.
Create a backup FD for FMPC/SP-3000. (See “2.3.3 Creating Backup FD for SP-3000 and LP5700”)
Shut down the SP-3000, FMPC, then Imaging Controller in this order.
This completes the FMPC installation and setup.
2.22 Creating Backup FD for FMPC/SP-3000
2.23 System Shutdown
IC SP FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
51/222
51
3 Installation for FRONTIER 355/375
Install the FMPC devices and software, and set them up for use.
Install the FMPC using the following procedure.
[New Installation]
FMPC = Frontier Manager Printer Controller
SP = ScannerLP = Printer
IC = Imaging Controller
3.1 Installation Procedure List
No. Procedures Location Refer to
1 IEEE1394 Board Installation FMPC See Section 2.2.1 on page 15
2 PC Preparations FMPC See Section 3.2 on page 53
3 Disabling of “Rack Auto Cleaning” SP See Section 3.3 on page 53
4 Creating Backup FD for SP-3000 and
LP1500/2000
SP See Section 3.4 on page 54
5 Replacing the ROM for Printer LP See Section 3.5 on page 55
6 Connecting FMPC, FRONTIER, LAN Cable
and Monitor Switcher
SP,LP,FMPC, Monitor Switcher See Section 3.6 on page 56
7 Turning on FMPC (PW: FRONTIER) FMPC See Section 3.7 on page 60
8 Disabling Network Connection on SP Side FMPC See Section 3.8 on page 60
9 IEEE1394 Driver Installation in SP(Ver.1.5
only)
When the scanner (SP) has the System
[A1] Ver.1.7, installing or updating of driver
in SP is not required.
SP See Section 3.9 on page 60
10 [A1] Stand-alone Version-Up [Ver.1.5 ->
Ver.1.7] and DI Print/Data Writing Software
[C4/C5] Client Installation in SP
SP See Section 3.10 on page 61
11 IEEE1394 Driver Pre-installation FMPC See Section 3.11 on page 63
12 Installing IEEE1394 Driver for SP in FMPC FMPC See Section 3.12 on page 64
13 Starting-up LP in ROM Mode and Checking
ROM Version (2.0-0X-000)
LP See Section 3.13 on page 65
14 Installing IEEE1394 Driver for LP in FMPC FMPC See Section 3.14 on page 65
15 FMPC [D20] Installation (Reinstall) with
Printer’s Backup FD
FMPC See Section 3.15 on page 66
16 DI Print/Data Writing Software [C4/C5] Client
Installation in FMPC
FMPC See Section 3.16 on page 69
17 Installation Information Setup for FMPC FMPC See Section 3.17 on page 70
18 Output Device Setup for SP and Restarting
SP
SP See Section 3.18 on page 70
19 Copying Print Size Table to FD then Copping
SP-3000 Print Size Table to FMPC
(In use of 3KPrintsizeCopyTool)
SP/FMPC See Section 3.19 on page 71
20 FMPC Output Device Setting in Imaging
Controller
IC See Section 3.20 on page 72
21 Enabling of “Rack Auto Cleaning” SP See Section 3.21 on page 73
22 Paper Condition Setup FMPC See Section 3.22 on page 73
23 Creating Backup FD for FMPC, SP-3000 and
LP1500/2000
FMPC/SP/LP See Section 3.23 on page 74
24 Operational Check FMPC/SP/LP/IC See Section 3.24 on page 75
25 System Shutdown SP/FMPC/IC See Section 3.25 on page 75
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
52/222
52
[Updating]
FMPC = Frontier Manager Printer Controller
SP = Scanner
LP = Printer
IC = Imaging Controller
No. Procedures Location Refer to
1 PC Preparations
Perform “(14) “Visual Notification” to ON in Dr.
Watson Dialog Box” and (15) Non-display
setting of Internet Explorer Dialog Box” in
“2.2.7 Windows Settings”.
FMPC See Section 3.2 on page 53
2 Disabling of “Rack Auto Cleaning” SP See Section 3.3 on page 53
3 Creating Backup FD for SP-3000,
LP1500/2000 and FMPC
SP/LP See Section 3.4 on page 54
4 Turning on FMPC (PW: FRONTIER) FMPC See Section 3.7 on page 60
5 IEEE1394 Driver Pre-installation in
SP(Ver.1.5 only)
When the scanner (SP) has the System
[A1] Ver.1.7, installing or updating of driverin SP is not required.
SP See Section 3.9 on page 60
6 [A1] Stand-alone Version-Up [Ver.1.5 ->
Ver.1.7] and DI Print/Data Writing Software
[C4/C5] Client Installation in SP
SP See Section 3.10 on page 61
7 Inserting the IEEE1394 Driver Disk then
Restarting FMPC
FMPC See Section 3.11 on page 63
8 IEEE1394 Dr iver for SP Installation in FMPC FMPC See Section 3.12 on page 64
9 Starting-up LP in ROM Mode and Checking
ROM Version (2.0-0X-000)
LP See Section 3.13 on page 65
10 IEEE1394 Driver for LP Instal lation in FMPC FMPC See Section 3.14 on page 65
11 FMPC [D20] Installation (User Version-up) FMPC See Section 3.15 on page 66
12 Enabling of “Rack Auto Cleaning” SP See Section 3.21 on page 73
13 Paper Condition Setup FMPC See Section 3.22 on page 73
14 Creating Backup FD for FMPC, SP-3000 and
LP1500/2000
FMPC/SP/LP See Section 3.23 on page 74
15 Operational Check FMPC/SP/LP/IC See Section 3.24 on page 75
16 System Shutdown SP/FMPC/IC See Section 3.25 on page 75
FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
53/222
53
(See “2.2 PC Preparations”)
For the installing procedures for 1394 board, See “2.2.1 IEEE1394 Board Installation”.
To minimize the waiting time for installation, select “No” for “Rack Auto Cleaning” in “[46B] Processor
Operating Condition Setup”.
NOTE:
After the settings are completed, set to “Yes” again.
3.2 PC Preparations
3.3 Disabling of “Rack Auto Cleaning”
Select “No”.
FMPC SP
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
54/222
54
The data backup FD should be kept in a fixed place
near the machine because it is used after
recovering from trouble or when installing FMPC.
1 Select [Setup and Maintenance] - [01 SystemOperation Setup and Check] - [0122 Data
Backup]
2 Prepare a floppy disk for data backup whenbacking up film scanner or printer processor
data.
3 Move the cursor to the "Destination" box andselect “Film Scanner” or “Printer processor”.
4 Click the [OK] button.
• “Making the backup of the data” message
appears.
5Insert the floppy disk into the drive of the maincontrol unit.
6 Click the [OK] button.
7 Upon completion of the backup, click the
[Cancel] button.
• Operation returns to the menu screen.
8 Remove the floppy disk from the disk drive.
IMPORTANT
If FRONTIER has the system [A1] Ver.1.5 or
Ver.1.6, insert the 1394 Driver Disk for SP-3000
(See “1.2 Checking the Kit Contents”), then
perform the post-operational check.
9 Perform the post-operational checks.
10 In case of updating, use the same procedures asthe above to perform creating backup FD for
FMPC.
3.4 Creating Backup FD for SP-3000 and LP1500/2000
SP FMPC
distributed by www.minilablaser.com
-
8/15/2019 Fuji Frontier 350-370 Installation - Service Manual - Parts List
55/222