full platform bed with drawers - shanty 2 chic · shanty-2-chic.com full platform bed with drawers...
TRANSCRIPT
Full Platform Bed With DrawersCopyright © 2015 Shanty-2-Chic.com
Full PlatForm Bed With draWers - Page | 2 shanty-2-ChiC.Com
Drill pocket holes as indicated by the arrows in the layout diagrams. The size pocket holes are noted at each step. The measurements in this plan are exact for this model. Measure and cut as you go to make sure everything lines up perfectly with your project. Read and
understand this entire plan before starting the project.
Supply List
Item Quantity Description
1 x 8 x 8’ 2 Pine or whitewood board
1 x 6 x 10’ 5 Pine or whitewood board
1 x 6 x 6’ 1 Pine or whitewood board
1 x 3 x 10” 2 Pine or whitewood board
1 x 3 x 8’ 1 Pine or whitewood board
1 x 2 x 6’ 2 Pine or whitewood board
2 x 4 x 8’ 3 Pine or whitewood board
2 x 3 x 8’ 3 Pine or whitewood board
2 x 2 x 8’ 12 Pine or whitewood board
2 x 6 x 22” Only 22” is needed. Get the shortest length you can
48” x 96” x 3/4” plywood 4
1-1/4” pocket hole screws 180
2-1/2” pocket hole screws 88
2-1/2” wood screws handful
Finish nails
Wood glue
Finish of choice
Drawer pulls 4
Full PlatForm Bed With draWers - Page | 3 shanty-2-ChiC.Com
Full PlatForm Bed With draWers - Page | 4 shanty-2-ChiC.Com
Plyw
ood la
yout
. All sh
eets
are
3/4
” plyw
ood
Full PlatForm Bed With draWers - Page | 5 shanty-2-ChiC.Com
Assemble the headboard and footboard support boards with wood glue and pocket hole screws. Drill pocket holes for
1-1/4” pocket hole screws on the plywood piece and 2-1/2” pocket hole screws on the 2 x 4 board.
Assemble two side frames with wood glue and 2-1/2” pocket hole screws. The center style is centered.
Assemble the frame upside down by attaching the headboard and
footboard supports to the side frames. Use 2-1/2” pocket hole screws in the
2 x material and use 1-1/4’ pocket hole screws in the plywood. The plywood does not extend all the way down
in this orientation. The 2 x boards are flush on top in this orientation.
Full PlatForm Bed With draWers - Page | 6 shanty-2-ChiC.Com
Add the hidden center foot and four corner feet with wood glue and finish
nails. The corner feet are flush with the sides but overhang the front by 3/4” and
overhang the back by 2-1/2”.
Carefully flip the assembly over and add the center support with
wood glue and 1-1/4” pocket hole screws. There should be screws going into each end as well as the lower center support
Measure and determine the exact sizes for the two mattress support frames. Cut and assemble these pieces with wood glue and 2-1/2”
pocket hole screws. The center 2x4 is centered and the 2 x 2 boards are
centered in the remaining space.
Full PlatForm Bed With draWers - Page | 7 shanty-2-ChiC.Com
Attach the mattress support frames with wood glue and finish nails through the headboard and footboard piece. Then predrill and use 2-1/2” screws to secure them
to the side frames and interior plywood support. These should be flush with the interior plywood and 3/4” below the top of the
side frames.
Attach the footboard boards with wood glue and finish nails starting with the outside vertical
boards. Then cut and install the interior three boards. These
will completely cover up the plywood and the pocket holes.
Attach the four1 x 2 drawer guides to the inside
faces of the headboard and footboard plywood panels with wood glue
and finish nails and attach the center 2 x 2 drawer
guides with wood glue and 2-1/2” wood screws
Full PlatForm Bed With draWers - Page | 8 shanty-2-ChiC.Com
Assemble the drawers by first attaching the front and back pieces to the sides with wood glue and 1-1/4” pocket hole screws. Then use glue and finish nails to attach the
bottom panel.
Make sure the drawers properly fit and attach the
drawer front with wood glue and finish nails from the inside.
Add all four drawers and install any drawer pulls you wish to use.
Full PlatForm Bed With draWers - Page | 9 shanty-2-ChiC.Com
Drill six pocket holes for 2-1/5” pocket holes on lower 10-1/2” of the inside faces of the headboard posts. Then attach the headboard slats to the side posts only with
wood glue and 1-1/4” pocket hole screws so that the front faces
are flush starting from the top and working your way down.
Drill pocket holes for 1-1/4” pocket hole screws on the top of the slat braces to attach the top board of the headboard later. Then use glue and finish nails to attach the braces directly to the back of the slats to hold everything together. Attach the top board with 1-1/4” pocket hole
screws through the braces and with 2-1/2” wood screws through the top
and into each leg on the ends.
Full PlatForm Bed With draWers - Page | 10 shanty-2-ChiC.Com
Attach the headboard to the platform assembly with 2-1/2” pocket hole screws through the lower part of the legs.
At this point the plywood mattress panels can be installed. That’s it! Sand
and finish as you wish. Add your mattress and make it unique! If you
decide to make this project be sure to stop by our website and show it off in
the Submit Your Project section!!