gds-series - zoho · gds-820/840 operation manual 44 note: gds-820/840 does not support gdi...
TRANSCRIPT
GDS-820/840 Operation Manual
0
GDS-820/GDS-840
GDS-820/840 Operation Manual
1
Due to continuous improvements in the GDS-820/840 Digital Storage
Oscilloscope, information contained in this manual is subject to change
without notice. Contact GW, for revisions and corrections.
GDS-820/840 Operation Manual
2
ATTENTION
GDS-820/840 Operation Manual
3
GDS-820/840 Operation Manual
4
GDS-820/840 Operation Manual
5
GDS-820/840 Operation Manual
6
*: Measurement category IV is for measurement performed at the source of low-voltage installation
Measurement category III is for measurement performed in the building installation
Measurement category II is for measurement performed on the circuits directly connected to the
low voltage installation
GDS-820/840 Operation Manual
7
GDS-820/840 Operation Manual
8
GDS-820/840 Operation Manual
9
Before
depress the ON/STBY pushbutton of front panel, the main power switch of
rear panel have to be switched on
GDS-820/840 Operation Manual
10
GDS-820/840 Operation Manual
11
GDS-820/840 Operation Manual
12
GDS-820/840 Operation Manual
13
*: The memory bar is always 500 points under RUN mode even the memory length is selected over 500 points, the oscilloscope is still displaying250points or 300points (menu off) on LCD screen waveform area.
GDS-820/840 Operation Manual
14
GDS-820/840 Operation Manual
15
GDS-820/840 Operation Manual
16
GDS-820/840 Operation Manual
17
GDS-820/840 Operation Manual
18
GDS-820/840 Operation Manual
19
GDS-820/840 Operation Manual
20
GDS-820/840 Operation Manual
21
GDS-820/840 Operation Manual
22
GDS-820/840 Operation Manual
23
GDS-820/840 Operation Manual
24
GDS-820/840 Operation Manual
25
GDS-820/840 Operation Manual
26
GDS-820/840 Operation Manual
27
GDS-820/840 Operation Manual
28
GDS-820/840 Operation Manual
29
GDS-820/840 Operation Manual
30
GDS-820/840 Operation Manual
31
GDS-820/840 Operation Manual
32
GDS-820/840 Operation Manual
33
GDS-820/840 Operation Manual
34
GDS-820/840 Operation Manual
35
GDS-820/840 Operation Manual
36
Note: All accuracy of these signals’ level are based on the probe 1 only
GDS-820/840 Operation Manual
37
Note: All accuracy of these signals’ level are based on the probe 1 only
GDS-820/840 Operation Manual
38
Note: The number select of “average” only effectiveness on the record
lengths of 500.
GDS-820/840 Operation Manual
39
(except record lengths of 500)
for this moment, the selection of average number is
ineffective
Note: The different between record lengths of 500 and the rest is the
“sampling”. If the “record lengths” is selected to 500, the sampling will be
triggered individually. If “record lengths” is the rest number, the sampling
is triggered for once.
GDS-820/840 Operation Manual
40
GDS-820/840 Operation Manual
41
GDS-820/840 Operation Manual
42
GDS-820/840 Operation Manual
43
Note: Always 250 points plotted to screen on each acquisition.
GDS-820/840 Operation Manual
44
Note: GDS-820/840 does not support GDI printers.
Note: The USB of this oscilloscope is “DEVICE” only, this oscilloscope
DO NOT support any USB printers.
Note: Printer menu is only available for GDS-820S, GDS-820C, GDS-840S,
and GDS-840C.
Note: Interface menu is only available for GDS-820S, GDS-820C,
GDS-840S, and GDS-840C.
GDS-820/840 Operation Manual
45
Note: The “Data Bit” is always 8-bit.
Note: In order to communicate both oscilloscope and computer, please
download the USB driver for our website http://www.goodwill.com.tw.
GDS-820/840 Operation Manual
46
GDS-820/840 Operation Manual
47
Note: The signal of “Go-No Go” BNC connector is “open collect”.
GDS-820/840 Operation Manual
48
GDS-820/840 Operation Manual
49
Note: All the judgment condition are based on the setting of
. See next page for details.
GDS-820/840 Operation Manual
50
GDS-820/840 Operation Manual
51
GDS-820/840 Operation Manual
52
GDS-820/840 Operation Manual
53
GDS-820/840 Operation Manual
54
GDS-820/840 Operation Manual
55
GDS-820/840 Operation Manual
56
GDS-820/840 Operation Manual
57
GDS-820/840 Operation Manual
58
GDS-820/840 Operation Manual
59
GDS-820/840 Operation Manual
60
GDS-820/840 Operation Manual
61
GDS-820/840 Operation Manual
62
GDS-820/840 Operation Manual
63
Data Terminal Equipmen
Note: RS-232 Interface is only available for GDS-820S, GDS-820C, GDS-840S,
and GDS-840C.
GDS-820/840 Operation Manual
64
Do not connect the output line of one DTE device to the output line of theother.
Many devices require a constant high signal on one or more input pins.
Ensure that the signal ground of the equipment is connected to the signalground of the external device.
Ensure that the chassis ground of the equipment is connected to thechassis ground of the external device.
Do not use more than 15m of cable to connect devices to a PC.
Ensure the same configurations are used on the device as the one used onPC terminal.
Ensure the connector for the both side of cable and the internal connectedline are met the demand of the instrument.
GDS-820/840 Operation Manual
65
GDS-820/840 Operation Manual
66
Performance Condition: The electrical specifications found in these tables of
warranted specifications apply when the oscilloscope has been adjusted at an
ambient temperature between +20 and +30 , a warm-up period at least 30
minutes are necessary. This oscilloscope is operating at an ambient
temperature between 0 and +50 only.
GDS-820/840 Operation Manual
67
GDS-820/840 Operation Manual
68
GDS-820/840 Operation Manual
69
GDS-820/840 Operation Manual
70
GDS-820/840 Operation Manual
71
Only for GDS-820S, GDS-820C, GDS-840S,GDS-840C
GDS-820/840 Operation Manual
72
GDS-820/840 Operation Manual
73