ge interlogix kalatel division product update ktd-405 programming & standard operations

GE Interlogix

Kalatel Division

Product Update

KTD-405 Programming& Standard Operations

KTD-405 Keypad Programming

KTD-405 keypad (Supervisor Programming)

KEYPAD ADDRESS: 99

KEYPAD 99

Boot-Up Screen


CAMERA ---

MONITOR 1

Default display after applying power

KTD-405 keypad (Programming)

Navigating the menus

Key FunctionDisplays the next menu

Displays the previous menu

Scrolls up when indicated by in the menus

Scrolls down when indicated by in the menus

Scrolls right when indicated by in the menus

Scrolls left when indicated by in the menus

Scrolls up, down, left or right when indicated by , , , in the menus

Advances menus; exits menus if held for 3 secondsseq

KTD-405 keypad (Programming)

NOT IMPLEMENTED

Menus that were not available in the first releases of software are indicated by two beeps and the following display:

Supervisor Programming


To Access Programming: Press and hold the key

The unit will beep and show the following display

Remote device programming must be accessed separately.

Supervisor programming password is 1,4,7,6,

Also includes All user programming

ENTER PROGRAMMING

CODE:

seq


Resetting the Factory Defaults The first menu to display will be this one.

Press to advance to the next menu and to return to the previous menu at any time without changing any existing parameters

RESET TO DEFAULTS? NO

<+>=YES <->=NO NEXT


1=RESET ALL BUT TITLES

2=RESET ALL

If you pressed “+” (yes): The next display will show:

Followed by:

Followed by:

The keypad will advance to the next menu automatically

ARE YOU SURE?

<+>=YES <->=NO NEXT

INITIALIZING DEFAULTS

PLEASE WAIT


Setting The Keypad Address The address is a “user defined” two-digit number

The address must be from 10 to 99

Each device on the RS-485 network must have a unique address

Address 99 is automatically assigned when the keypad is first connected and will remain unless changed by the user

Entering an address that is already used temporarily displays:

Select or to skip over this menu

KEYPAD ADDRESS: 99

(01-99) NEXT

ADDRESS NOT AVAILABLE


Backward Compatibility? If the KTD-405 is being used in a system with:

Existing ProBridges

Existing CBR-KB3 or CBR-KB3/J keypads

Select YES to allow the KTD-405 to communicate properly with these devices.


KB3 PTZ PROTOCOL? NO

<+>=YES <->=NO NEXT


Allow Remote Programming by user? If the KTD-405 is being used in a system with:

Matrix Switchers or Multiplexers

Alarm Monitoring Equipment

Programmable Dome Cameras or Receivers

Select YES to allow the user to enter the 9,5,1, password and program these devices


ENABLE REMOTE PRGMG? YES

<+>=YES <->=NO NEXT

seq


Programming Keypad Titles A keypad title can be up to 14 characters including:

A – Z and 0 - 9

Keypads with titles can use the “Seize Control” option

Supervisors can seize camera sites, multiplexers, VCRs, etc.

Supervisors can seize an entire zone in the ZONE mode

Use the joystick or these buttons to program the title


KEYPAD TITLE: <>

NEXT

= , = , = , = ,


Changing the SEIZE CONTROL code Use the number keys to enter the new code

The keypad will advance to the next menu when the last digit is entered


SEIZE CONTROL CODE: 8642

USE NUMBER KEYS NEXT


Changing the SEIZE CONTROL time Use the number keys to enter the new time

This is the number of minutes of inactivity before the keypad will exit the seize control mode


SEIZE CONTROL TIME: 5

(1-10) MINUTES NEXT


Restricting access to presets Use the number keys to enter the new limit

This is the lowest preset number a user may change


LOWEST USER PRGMD PRESET

(01-64) 58 NEXT


Programming the SOFT keys This feature is not yet implemented

Select -, or to skip over this menu

Pressing + displays the following message:

PROGRAM SOFT KEYS?

<+>=YES <->=NO NEXT

NOT IMPLEMENTED


Programming the ACCESS codes This feature is not yet implemented

Select -, or to skip over this menu

Pressing + displays the following message:

CHANGE ACCESS CODES?

<+>=YES <->=NO NEXT

NOT IMPLEMENTED

User Programming

KTD-405 keypad (User Programming)

To Access User Programming: Press and hold the key


User programming password is 5,7,9,

ENTER PROGRAMMING

CODE:

seq


Changing the Operating Mode Two choices are available:

Digiplex

Zone

Use the joystick or these buttons to select the mode


OPERATING MODE: DIGIPLEX

<,>=SELECT NEXT

= , =


Setting the system size Enter the highest camera number in your system


SYSTEM SIZE:

<CAMERAS> 511 NEXT

DigiPlex mode Menus


Setting the system size Enter the highest monitor number in your system


SYSTEM SIZE:

<MONITORS> 64 NEXT

DigiPlex mode Menus


Setting the system size Enter the highest multiplexer number in your system


SYSTEM SIZE:

<MPLXS> 32 NEXT

DigiPlex mode Menus


Setting the system size Enter the highest VCR number in your system


SYSTEM SIZE:

<DSR/VCR> 32 NEXT

DigiPlex mode Menus


Setting the system size Enter the highest preset number in your system


SYSTEM SIZE:

<PRESETS> 63 NEXT

DigiPlex mode Menus


Restricting system access This menu restricts access to specified cameras

Use the joystick or these buttons to select the camera


CAMERA 000 ACCESS? YES

<+>=YES <->=NO NEXT

DigiPlex mode Menus

= , =


Restricting system access This menu restricts access to specified monitors

Use the joystick or these buttons to select the monitor


MONITOR 01 ACCESS? YES

<+>=YES <->=NO NEXT

DigiPlex mode Menus

= , =


Restricting system access This menu restricts access to specified recorder

Use the joystick or these buttons to select the recorder


Pressing “+” displays this menu:

Enter a number from 0 to 511, or 0 for NONE or


DSR/VCR 01 ACCESS? YES

<+>=YES <->=NO NEXT

DigiPlex mode Menus

VCR 01 MATRIX INPUT:

000 <0=NONE> NEXT

= , =


Restricting system access This menu restricts access to specified multiplexer

Use the joystick or these buttons to select the multiplexer


MPLX 01 ACCESS? YES

<+>=YES <->=NO NEXT

DigiPlex mode Menus

= , =


If you pressed “+” (yes): The next display will show:

Followed by:

Followed by:

The keypad will advance to the next multiplexer menu automatically

MPLX01 BRAND CBR DVMRe

<,>=SELECT NEXT

MPLX 01 MATRIX INPUT?

000 <0=NONE NEXT

SELECT MAX OUTPUTS: 02

<,>=SELECT NEXT

DigiPlex mode Menus


Programming the monitor offset Enter a number for the offset needed in your system


MONITOR OFFSET

NUMBER: 0 NEXT

DigiPlex mode Menus


Queuing and announcing call-ins If you select “+” in this display:

You need to select either SINGLE or MULTIPLE tone here:

Also specify a monitor to display the queued calls:


ANNUNCIATION? NO

<+>=YES <->=NO NEXT

CALL TONE TYPE? MULTIPLE

<,>=SELECT NEXT

SPOT MONITOR NUMBER: 0

<0=UNASSIGNED> NEXT

DigiPlex mode Menus


End of menus notification Pressing from the previous menu will cause the

keypad to display this message:

Select or press and hold for 3 seconds to exit the menus

PRESS <SEQ> FOR 3

SECONDS TO EXIT

DigiPlex mode Menus

seq


Changing the Operating Mode Two choices are available:

DigiPlex

Zone



OPERATING MODE: ZONE

<,>=SELECT NEXT

= , =


Programming the Mode label This menu allows you to select one of several labels for

the LCD display during normal operations

Selections Include:

ZONE, MPLX, DVMR, TERR, BLDG

FLR, DEPT, STA, SITE, AREA


LCD DISPLAY LABEL: ZONE

<,>=SELECT NEXT

Zone mode Menus


Programming the zone titles This menu allows you to select a title to display when

the specified zone is being accessed.


Enter a two-digit code and the keypad will advance to the following menu automatically

Program the label characters the same way as keypad titles


ENTER ZONE ADDRESS: 01

(01-16) NEXT

Zone mode Menus

ZONE 01 TITLE: <>

(01-16) NEXT


Programming the Zone type This menu allows you to identify the specific device

that makes up a zone:

Selections Include:

CALIBUR MMX, CBR DVMRe, CBR TRIPLEX,

CBR DUPLEX, CBR SIMPLEX, MATRIX SWCH,


ZONE 01 HUB: CBR DVMRe

<,>=SELECT NEXT

Zone mode Menus


Setting the zone size (monitors) This menu restricts access only to available zone monitors

Use the number buttons to set the number of monitors


Setting the zone size (cameras) This menu restricts access only to available zone cameras

Choices include 4, 9, 10, 16 and 32



ZONE 01 MON. OUTPUTS?

01 TO 02 NEXT

Zone mode Menus

ZONE 01 CAM. INPUTS? 16

<,>=SELECT NEXT

= , =


Programming zone access privileges Program the cameras that this keypad can access:

Program the monitors that this keypad can access:

Program user access to the zone’s recorder :

You should deny access unless you have a Triplex or MMX connected to a VCR using sub-macros.

ZONE 1 CAM 01 ACC? YES

<+>=YES <->=NO NEXT

ZONE 1 MON 01 ACC? YES

<+>=YES <->=NO NEXT

ZONE 1 RECORDER ACC? YES

<+>=YES <->=NO NEXT

Zone mode Menus


If the Zone type is set to MATRIX SWCH: The zone size and access menus displays are slightly

different

ZONE 02 HUB: MATRIX SWCH

<,>=SELECT NEXT

Zone mode Menus


Programming zone size Program the first camera input number for this zone:

Program the number of monitors for this zone:

Program the number of camera inputs on this zone:

Choices include 4, 9, 10, 16 and 32

SELECT START INPUT: 032

<,>=SELECT NEXT

ZONE 02 MON. OUTPUTS:

01 TO 16 NEXT

ZONE 02 CAM. INPUTS: 64

<,>=SELECT NEXT

Zone mode Menus


Programming zone access privileges Program the cameras that this keypad can access:

Program the monitors that this keypad can access:

Program user access to the zone’s recorder :

You should deny access unless you have a Triplex or MMX connected to a VCR using sub-macros.

ZONE 02 CAM 01 ACC? YES

<+>=YES <->=NO NEXT

ZONE 02 MON 01 ACC? YES

<+>=YES <->=NO NEXT

ZONE 02 RECORD ACC? YES

<+>=YES <->=NO NEXT

Zone mode Menus


Queuing and announcing call-ins If you select “+” in this display:

You need to select either SINGLE or MULTIPLE tone here:

Also specify a monitor to display the queued calls:


ANNUNCIATION? NO

<+>=YES <->=NO NEXT

CALL TONE TYPE? MULTIPLE

<,>=SELECT NEXT

SPOT MONITOR NUMBER: 0

<0=UNASSIGNED> NEXT

Zone mode Menus


End of menus notification Pressing from the previous menu will cause the

keypad to display this message:

Select or press and hold for 3 seconds to exit the menus

PRESS <SEQ> FOR 3

SECONDS TO EXIT

Zone mode Menus

seq

Remote Programming

KTD-405 keypad (Remote Programming)

To Access Remote Programming: Press and hold the key


User programming password is 9,5,1,

Correct password entry will cause the following display:

Each selection generates a different set of menus

ENTER PROGRAMMING

CODE:

1=SWITCHER/MPLX 2=ALARMS

3=CAMERA/RCVR EXIT

seq


Switcher/Multiplexer Programming Identify the device to be programmed

If you select “1” (440) enter the monitor number to use for programming the switcher

The keypad will display this message

1=440 2=CALIBUR

3=340/348 BACK

ENTER MONITOR NUMBER:

(1-64) BACK

SEE MONITOR FOR MENUS

HOLD SEQ <3 SEC> TO EXIT

Switcher/Mux Menus


Identify the device to be programmed

If you select “2” (CALIBUR) enter the RS-485 address of the unit to be programmed


1=440 2=CALIBUR

3=340/348 BACK

ENTER CALIBUR ADDRESS:

(1-32) BACK



Switcher/Mux Menus


Identify the device to be programmed

If you select “3” (340/348) enter the monitor number to use for programming the switcher


1=440 2=CALIBUR

3=340/348 BACK

ENTER MONITOR NUMBER:

(1-64) BACK



Switcher/Mux Menus


Alarm Programming The keypad will display this message



Alarm Menu


Camera/Receiver Programming (DigiPlex) Identify the device to be programmed

If you select “1” (CYBERDOME) enter the camera address to be programmed


1=CYBERDOME 2=PTZ

3=AUXILIARY BACK

ENTER CYBERDOME SITE

NUMBER BACK



Camera/Receiver Menus


Camera/Receiver Programming (Zone) Identify the device to be programmed, AND Make

sure you have selected the Zone before you enter programming

If you select “1” (CYBERDOME) enter the camera address to be programmed (address must be within the zone)


1=CYBERDOME 2=PTZ

3=AUXILIARY BACK

ENTER ZONE 1 CAMERA

NUMBER__ BACK



Camera/Receiver Menus


PTZ OR Auxiliary Programming If you select “2” or “3” from this menu


1=CYBERDOME 2=PTZ

3=AUXILIARY BACK

NOT IMPLEMENTED

PTZ/Auxiliary Menus

Standard Operation

KTD-405 keypad (Standard Operation)

CAMERA ---

MONITOR 1

Default display after applying power

DigiPlex mode

Zone Mode

ZONE – ZONE TITLE

CAMERA -- MONITOR -


Accessing System Information: Press and hold the key to display the system

information

The keypad will display

Use or to move between these additional system information displays

KEYPAD ADDRESS: 99

KEYPAD 99 NEXT

VERSION 0.1.07

Dec 20 2001 09:32:44

CAM MN MX RC PS QS MO AT

511 64 32 32 63 58 00 W

mon


Accessing Help displays: Press + to display the Help menu

In the help menus:

Pressing any key displays that key’s function

+ “key” displays that key’s shifted function

The help display will cease display after 10 seconds of inactivity

esc

esc

mon


Selecting a monitor: There are two ways:

Enter the monitor number with any preceding zeroes

Example: 1 (systems with less than 10 cameras)

Example: 01 (systems with more than 9 cameras)

Enter the monitor number, then press

Example: 1 +

CAMERA ---

MONITOR 1


Selecting a camera: There are two ways:

Enter the camera number with any preceding zeroes



Example: 003 (systems with more than 99 cameras)

Enter the camera number, then press

Example: 3 +

CAMERA ---

MONITOR 1


Controlling a camera: Select the camera to be controlled

Pan, Tilt and Zoom can be controlled by the joystick

Up/Down for Tilt control

Left/Right for Pan control

Twist the joystick for Zoom or use the key

Use the and keys for these functions

CAMERA 003

MONITOR 1

+zoom-

+iris- +focus-


Setting a preset: Position the camera

Press the Store key

Enter the preset number in one of three ways:

Enter the two-digit number (Ex. 05 or 16)

Use the AUX-1, AUX-2, AUX-3 or AUX-4 keys for 58-61

Use and for presets 62 and 63 (left and right Auto-Pan limits. Presets 62 and 63 can not be set by entering the two-digit numbers. On with these two keys and .

aux 1

store

KTD-405 keypad (Standard Operation)Programming a Groups (salvos) and Tours: Requires a RS-485 connection and zone selected

Requires Switcher monitor groups to be previously programmed

Press Store + Sequence

This menu will display:

Enter a number from 1 to 64 calls that group of cameras on the monitors

If you press the Tour key the following menu is displayed:

Enter a number from 1 to 12 TO START that group sequence on the monitors

DigiPlex Mode

ENTER MONITOR GROUP

(1-64)-- OR <TOUR>

store seq

ENTER GROUP SEQUENCE

(1-12)--

tour

KTD-405 keypad (Standard Operation)Controlling a recording device: Requires a KTD-93 interface (RS-422 to RS-232)

Key Function DSR/VCR Function DVMRe

Starts recording Starts recording

Stops record or playback Stops record or playback

Starts playback Starts playback

Pauses playback Pauses playback or live mode

Fast Forward Fast Forward

Fast Reverse (rewind) Fast Reverse (rewind)

Frame advance

Depends on device (DSR/VCR)

Play forward (from reverse play)

Frame advance (in pause mode)

Frame reverse


Play reverse (from forward play)

Frame reverse (in pause mode

n/a 2X digital zoom toggle

n/aActivates play and displays search menu

Digiplex Mode


Key Function DSR/VCR Function DVMRe

Joystick

functions

↻ Twist right = variable rate forward

↺ Twist left = variable rate reverse

In Play or Pause modes:



Skip forward 2MB (about 15 sec.)

Skip backward 2MB (about 15 sec.)

Fast Forward

Fast Reverse (rewind)

Return to center position resumes pause mode

In 2X Zoom mode:

Tilt up

Tile down

Pan right

Pan left

Digiplex Mode

KTD-405 keypad (Standard Operation)Controlling a multiplexer: Requires RS-485 connection

Key Function Multiplexer Function VCR/DSR

Starts recording Starts recording

Stops record or playback Stops record or playback

Starts playback Starts playback

Pauses playback Pauses playback or live mode

Fast Forward Fast Forward

Fast Reverse (rewind) Fast Reverse (rewind)

Frame advanceFrame advance (in pause mode)

Frame reverseFrame reverse (in pause mode

2X digital zoom toggle n/a

Activates play and displays search menu

n/a

Zone Mode

Multiplexer must support sub-macro VCR interface

KTD-405 keypad (Standard Operation)Controlling a multiplexer: Requires a RS-485 connection

Key Function Multiplexer Function DSR/VCR

Joystick

functions

n/a

In Play or Pause modes:



In 2X Zoom mode:

Tilt up

Tile down

Pan right

Pan left

Zone Mode

Multiplexer must support sub-macro VCR interface

KTD-405 keypad (Standard Operation)Programming a multiplexer AutoList sequence: Requires a RS-485 connection and zone selected

Press Store

Press Sequence

This menu will display:

Enter the first camera number in the sequence

Wait the desire amount of time you want this camera displayed

Enter the next camera number in the sequence

Wait the desire amount of time you want this camera displayed

Repeat procedure until all cameras have been entered in the sequence

Press to cancel or to exit and save the sequence and exit

Zone Mode

ENTER SEQUENCE CAMERA

CANCEL DONE

store

seq


Key Function DSR/VCR

Starts recording

Stops record or playback

Starts playback

Pauses playback

Fast Forward

Fast Reverse (rewind)

Frame advance


Frame reverse


Joystick↻ Twist right = variable rate forward


Zone Mode

KTD-405 keypad (Standard Operation)Programming a Calibur™ multiplexer: Requires RS-485 connection

Enter programming via the Remote Programming code 9,5,1,

Select 1 for switcher/multiplexer

Select 2 for Calibur

Enter the Calibur RS-485 address

Press (ENTER)

Enter the Calibur password for the device

Zone Mode

seq

KTD-405 keypad (Standard Operation)Programming a Calibur™ multiplexer: Navigate the Calibur multiplexer menus with these keys:

Key Function

Joystick moves left, right, up, down in menus

Makes selections

Backspaces out of selections or exits programming from the main menu

Move up in menus

Move down in menus

Move right in menus

Move left in menus

Same as

Same as

Zone Mode

esc

KTD-405 keypad (Standard Operation)Keys with special functions: These keys have some special applications:

Key Function

Programmable two ways:

Use with number keys to display mult-image views (if supported)

Used to sequence through multi-display image views (if supported)

OPEN or Preset 58

CLOSE or Preset 59

STOP or Preset 60

TALK or Preset 61

Used for activating tours or Auto-Pan mode

Used to send the selected camera to a preset (if camera is capable)

Clears numerical menu entries (future function clears alarms)

Places selected CyberDome in auto-focus

Addresses remote recording device

view

aux 1

aux 2

aux 3

aux 4

tour

find

dsr/vcr

autofocus

esc

KTD-405 keypad (Standard Operation)Keys with special functions: These keys have not been implemented yet:

Key Function

Alarm key

1st (First) key

alarm

1st

PYTANIA

ge interlogix kalatel division product update ktd-405 programming & standard operations

Documents

keypad programmingktd

keypad supervisor programming1

keypad programmingnavigating

keypad addressthe address

supervisor programmingktd

menukeypad address

digit numberthe address

default display