gearbox manual dg350 2017 - drenth gearboxes · gearbox manual dg350 – revision: 006 pole...

Gearbox Manual DG350

2017

2

Gearbox Manual DG350 – Revision: 006

Pole Position

In Gearboxes

Warning Please be aware that information in this manual may be inaccurate, incomplete or contain typographical errors. The content of this manual is subject to

change without notice and should, therefore, be used for informational purposes only. Consequently, replacement parts must always by ordered according

to the part number engraved on the part.

If you find information in this manual that is incorrect or incomplete, we would appreciate your comments and suggestions.

3


Pole Position

In Gearboxes

Contents Warning ............................................................................................................................................................................................................................................. 2

Contents ............................................................................................................................................................................................................................................ 3

1. Technical Specifications................................................................................................................................................................................................................. 5

1.1. General Specifications ............................................................................................................................................................................................................ 6

1.2. General Dimensions ................................................................................................................................................................................................................ 7

1.2.1. Ford T9 – Short Version.................................................................................................................................................................................................... 7

1.2.2. Toyota GT86 ..................................................................................................................................................................................................................... 8

1.2.3. Ford T9 - Direct Replacement .......................................................................................................................................................................................... 9

1.2.4. BMW .............................................................................................................................................................................................................................. 10

1.3. Oil System ............................................................................................................................................................................................................................. 11

2. Gearbox Assembly ....................................................................................................................................................................................................................... 12

2.1. General Instruction Notes..................................................................................................................................................................................................... 13

2.2. Bearing Assembly .................................................................................................................................................................................................................. 14

2.3. Gearbox Assembly Ford T9 ................................................................................................................................................................................................... 16

2.4. Gearbox Assembly Toyota GT86 ........................................................................................................................................................................................... 56

2.5. Gearbox Assembly BMW E30 (Old Type) .............................................................................................................................................................................. 60

2.6. Gearbox Assembly BMW E30 (New Type) ............................................................................................................................................................................ 62

2.7. Gearbox Assembly Opel ........................................................................................................................................................................................................ 64

2.8. Rotary Sensor ........................................................................................................................................................................................................................ 68

3. Gear Ratio List ............................................................................................................................................................................................................................. 70

4. Accessories .................................................................................................................................................................................................................................. 72

4.1. Bellhousings / Adaptor Plates ............................................................................................................................................................................................... 73

4


Pole Position

In Gearboxes

4.2. Gearbox Brackets .................................................................................................................................................................................................................. 75

4.3. Gear Lever ............................................................................................................................................................................................................................. 76

4.4. DMS Gear Lever .................................................................................................................................................................................................................... 79

4.5. Gear lever Brackets ............................................................................................................................................................................................................... 81

4.6. Gear Indicator ....................................................................................................................................................................................................................... 82

4.7. Display Unit ........................................................................................................................................................................................................................... 83

4.8. Switchbox .............................................................................................................................................................................................................................. 84

4.9. Oil Breather Catchtank ......................................................................................................................................................................................................... 85

5. Assembly Tooling ......................................................................................................................................................................................................................... 86

6. Contact Information .................................................................................................................................................................................................................... 89

6.1. Contact Details ...................................................................................................................................................................................................................... 90

Appendix A: Technical Bulletin ........................................................................................................................................................................................................ 91

Appendix B: Amendments ............................................................................................................................................................................................................... 93

5


Pole Position

In Gearboxes

1. Technical Specifications

6


Pole Position

In Gearboxes

1.1. General Specifications

DG350

Application Circuit, Hill Climb & Rally

Type 6-Speed Sequential

Torque rating 350 Nm

Weight (dry weight) 27.5 kg

7


Pole Position

In Gearboxes

1.2. General Dimensions

1.2.1. Ford T9 – Short Version

8


Pole Position

In Gearboxes

1.2.2. Toyota GT86

9


Pole Position

In Gearboxes

1.2.3. Ford T9 - Direct Replacement

10


Pole Position

In Gearboxes

1.2.4. BMW

11


Pole Position

In Gearboxes

1.3. Oil System A gerotor internal-gear pump is standard in the DG350. The oil pump is used to feed oil to the bearings, gears, dog rings and drop gears. The oil can be fed

to an external oil cooler from the oil-out port and returned to the gearbox using the oil-in port. On the right and left side of the main housing an M12x1.50

thread is provided to mount oil temperature and pressure sensors. On top of the gearbox a D-06 adaptor is mounted which needs to be connected to an oil

catch tank or has to be replaced with a breather.

Oil Type Motul 75W140 Gear Competition

Oil Quantity 1.1 litres (excluding external oil lines & oil cooler)

12


Pole Position

In Gearboxes

2. Gearbox Assembly

13


Pole Position

In Gearboxes

2.1. General Instruction Notes The following information is intended for mechanics to (dis)assemble the gearbox. This is illustrated using exploded views including the corresponding Bill Of

Materials (BOM). Specific notes related to the (dis)assembly of a part are shown in the notes column of the BOM. For more details on the bearing

installation see §2.2 Bearing Assembly.

Please read the manual and make sure all parts are present before starting to assemble. Also ensure that all parts are clean and undamaged. It is

recommended to replace nuts, seals and circlips after removal. Only genuine Drenth Gearboxes parts should be used when overhauling the gearbox.

14


Pole Position

In Gearboxes

2.2. Bearing Assembly To reduce the risk of bearing or casing damage, heat mounting is used to install or remove bearings. Drenth Gearboxes highly recommend to use an oven to

ensure an even heat distribution. Casings should not be heated above 130°C. Fit the bearings promptly after removing the casing from the oven to avoid

extra heating cycles being required.

15


Pole Position

In Gearboxes

16


Pole Position

In Gearboxes

2.3. Gearbox Assembly Ford T9

17


Pole Position

In Gearboxes

18


Pole Position

In Gearboxes

19


Pole Position

In Gearboxes

20


Pole Position

In Gearboxes

21


Pole Position

In Gearboxes

22


Pole Position

In Gearboxes

23


Pole Position

In Gearboxes

24


Pole Position

In Gearboxes

25


Pole Position

In Gearboxes

26


Pole Position

In Gearboxes

27


Pole Position

In Gearboxes

28


Pole Position

In Gearboxes

29


Pole Position

In Gearboxes

30


Pole Position

In Gearboxes

31


Pole Position

In Gearboxes

32


Pole Position

In Gearboxes

33


Pole Position

In Gearboxes

34


Pole Position

In Gearboxes

35


Pole Position

In Gearboxes

36


Pole Position

In Gearboxes

37


Pole Position

In Gearboxes

38


Pole Position

In Gearboxes

39


Pole Position

In Gearboxes

40


Pole Position

In Gearboxes

41


Pole Position

In Gearboxes

42


Pole Position

In Gearboxes

43


Pole Position

In Gearboxes

44


Pole Position

In Gearboxes

45


Pole Position

In Gearboxes

46


Pole Position

In Gearboxes

47


Pole Position

In Gearboxes

48


Pole Position

In Gearboxes

49


Pole Position

In Gearboxes

50


Pole Position

In Gearboxes

51


Pole Position

In Gearboxes

52


Pole Position

In Gearboxes

53


Pole Position

In Gearboxes

54


Pole Position

In Gearboxes

55


Pole Position

In Gearboxes

56


Pole Position

In Gearboxes

2.4. Gearbox Assembly Toyota GT86

57


Pole Position

In Gearboxes

58


Pole Position

In Gearboxes

59


Pole Position

In Gearboxes

60


Pole Position

In Gearboxes

2.5. Gearbox Assembly BMW E30 (Old Type)

61


Pole Position

In Gearboxes

62


Pole Position

In Gearboxes

2.6. Gearbox Assembly BMW E30 (New Type)

63


Pole Position

In Gearboxes

64


Pole Position

In Gearboxes

2.7. Gearbox Assembly Opel

65


Pole Position

In Gearboxes

66


Pole Position

In Gearboxes

67


Pole Position

In Gearboxes

68


Pole Position

In Gearboxes

2.8. Rotary Sensor

The gearboxes come with a Penny & Giles SRH280DP rotary sensor. The rotary sensor signal is used to show the engaged gear on the Drenth Display Unit /

Drenth Gear Indicator or any other display. For correct gear indication, it is necessary that rotary sensor is properly connected and calibrated. Information

related to the wiring of the sensor is shown in the table below.

Cable Colour Description

Red + 5 V Supply

Yellow Output 1

White Output 2

Black 0 V Supply (GND)

Depending on the type of gearbox, Output 1 or Output 2 is used. The table below shows which output is used for the different types of gearboxes:

Gearbox Type Output Cable Colour

DG350 Output 2 White

DG350 Direct Replacement Output 1 Yellow




DGT250 Output 2 White

DGT350 Output 2 White

Mitsubishi Lancer Evolution VI-IX Output 1 Yellow

Mitsubishi Lancer Evolution X Output 1 Yellow

MPG Output 1 White

69


Pole Position

In Gearboxes

The connection diagrams when using output 1 or output 2 are shown below:

Please note that the above information does not apply to other sensors!

70


Pole Position

In Gearboxes

3. Gear Ratio List

71


Pole Position

In Gearboxes

The available gear ratios for the DG350 are shown in the table below. In addition, customer specific gear ratios can be developed, produced and supplied.

Layshaft Ratios Gear Ratios Constant Gear

Ratio

1st 2nd, 3rd, 4th, 5th & 6th

2.615 2.133 1.824 1.556 1.250 1.042 1.042

2.500 2.067 1.765 1.474 1.182 1.0001

2.286 2.063 1.722 1.412 1.136 0.889

1.933 1.667 1.350 1.107 0.857

1.875 1.611 1.300 1.091 0.828

1 Prise-direct

72


Pole Position

In Gearboxes

4. Accessories

73


Pole Position

In Gearboxes

4.1. Bellhousings / Adaptor Plates Drenth Gearboxes offers a variety of removable bellhousings and adaptor plates to mount the DG400 into different vehicles. In addition, bellhousings and

adaptor plates for customer specific applications can be developed, produced and supplied

74


Pole Position

In Gearboxes

75


Pole Position

In Gearboxes

4.2. Gearbox Brackets The Drenth gearbox brackets are designed to mount the DG400 using the existing chassis mounting points of the specific vehicle. Please note that these

brackets can only be used in vehicles where the chassis mounting points and/or the position of the engine have not been modified.

76


Pole Position

In Gearboxes

4.3. Gear Lever Drenth Gearboxes offers a one-piece aluminium gear lever which, in combination with shift rods or a push/pull cable, can be used on any Drenth sequential

gearbox to change gear. Several gearbox and chassis mounted brackets are available for mounting the gear lever at the desired position.

In order to suit a variety of applications, the gear lever comes in two different lengths:

• 260 mm • 360 mm

77


Pole Position

In Gearboxes

78


Pole Position

In Gearboxes

79


Pole Position

In Gearboxes

4.4. DMS Gear Lever Drenth Gearboxes offers a one-piece DMS aluminium gear lever with integrated electronics which, in combination with shift rods or a push/pull cable, can

be used on any Drenth sequential gearbox to change gear. The analogue output signal of the gear lever electronics can be used to configure the ignition cut

enabling flat-shifting. An optional Switchbox is used to convert the analogue signal when a digital output signal for programming the ignition cut is required.

The DMS gear lever can also be used to program down shift throttle blip if the car is equipped with drive-by-wire. In addition, several gearbox and chassis

mounted brackets are available for mounting the gear lever at the desired position.

In order to suit a variety of applications, the gear lever comes in two different lengths:

• 260 mm • 360 mm

80


Pole Position

In Gearboxes

81


Pole Position

In Gearboxes

4.5. Gear lever Brackets Drenth Gearboxes offers various types of gear lever brackets for mounting the (DMS) gear lever in the car. There can be chosen between two types of

brackets, namely gearbox mounted gear lever brackets and tunnel mounted gear lever brackets.

82


Pole Position

In Gearboxes

4.6. Gear Indicator Designed to work seamlessly with every Drenth sequential gearbox, the gear indicator uses the rotary sensor signal to show the selected gear. Using the

supplied software, it is possible to show up to 8 forward gears as well as neutral and reverse on the display with integrated light sensor. In addition, the gear

indicator features an option to control the reversing light.

Features:

- Gear indication

- Reverse light

- Automatic calibration

83


Pole Position

In Gearboxes

4.7. Display Unit Designed to work seamlessly with every Drenth sequential gearbox, the display unit uses the rotary sensor signal to show the selected gear. Using the

supplied software, it is possible to show up to 8 forward gears as well as neutral and reverse on the display with integrated light sensor. In addition, the

display unit features an adjustable shift light and an option to control throttle blip or the reversing light. In combination with the DMS gear lever, the display

unit can be used for flat-shifting which allows the user to set the cut time for each gear separately. This is also possible when using any other load cell,

Switchbox or switch.

Features:

• Gear indication • Shift light • Flat-shifting • Down shift throttle blip / Reverse light • Automatic calibration • DMS Gear Lever calibration

84


Pole Position

In Gearboxes

4.8. Switchbox The Drenth Gearboxes Switchbox is an analog-to-digital converter which is used in combination with the Drenth Display Unit or a programmable ECU to

enable flat-shifting. When a digital output signal is required for setting the ignition cut the Switchbox is used to convert the analogue signal. Because the

Switchbox is equipped with two potentiometers, the upshift and downshift threshold levels can be adjusted as desired.

Features:

• Adjustable downshift threshold voltage

• Adjustable upshift threshold voltage

85


Pole Position

In Gearboxes

4.9. Oil Breather Catchtank Drenth Gearboxes recommends the use of an Oil Breather Catch Tank for breathing the gearbox. Therefore Drenth Gearboxes offers a universal catch tank

which can be used with any gearbox. The set includes the breather catch tank, oil hose and the necessary adaptors.

86


Pole Position

In Gearboxes

5. Assembly Tooling

87


Pole Position

In Gearboxes

Optionally, Drenth Gearboxes provide tools which are used for assembling and disassembling the DG350. The tools listed below make it possible to perform

maintenance on the DG350:

88


Pole Position

In Gearboxes

89


Pole Position

In Gearboxes

6. Contact Information

90


Pole Position

In Gearboxes

6.1. Contact Details Drenth Motorsport Gearboxes

Fleuweweg 10

7468 AG Enter

The Netherlands

www.drenth-gearboxes.com

Spare Parts: +31 (0)547 38 26 96 [email protected]

91


Pole Position

In Gearboxes

Appendix A: Technical Bulletin

92


Pole Position

In Gearboxes

93


Pole Position

In Gearboxes

Appendix B: Amendments

94


Pole Position

In Gearboxes

Date Page Modification 18-10-2017 1st Issue of completely revised manual

26-06-2018 70 Added chapter 4.1 Bellhousings

28-06-2018 71 Added Adaptor Plates to chapter 4.1

18-07-2018 10 Changed oil type to Motul 75W140 Gear Competition

16-10-2018 61 & 62 Added BMW E30 New Type

22-10-2018 80 Added Assembly Bracket Gearlever Universal

07-02-2019 10 Added dimension drawing BMW

T +31 (0)547 38 26 96 E [email protected] W www.drenth-gearboxes.com

gearbox manual dg350 2017 - drenth gearboxes · gearbox manual dg350 – revision: 006 pole...

Documents