gears heat treatment

17
Heat Treatment Processes In Gear Design Prepared By: NATALINO FONSECA natalinofonseca81@gmail.com

Upload: natalino-fonseca

Post on 09-Jan-2017

370 views

Category:

Documents


6 download

TRANSCRIPT

Page 1: GEARS HEAT TREATMENT

Heat Treatment Processes In Gear Design

Prepared By: NATALINO FONSECA

[email protected]

Page 2: GEARS HEAT TREATMENT

Heat Treatment Processes It is a process of heating cycles where the

metal is subjected to controlled temperature changes in solid state. Heating process can change the size and shape of grain structure and can also change the constituents and hence the properties of steel.

Page 3: GEARS HEAT TREATMENT

Fe-C equilibrium diagram showing temperature ranges for various heat treatment processes.

Page 4: GEARS HEAT TREATMENT

Types of Heat Treatment1.Annealing2. Normalizing3. Quenching or Hardening4. Tempering5. Surface Hardening6. Case Hardening7. Austempering8. Marquenching9. Ausforming

Page 5: GEARS HEAT TREATMENT

Hardening Processes for Gears There are mainly following 3 processes

which are used for hardening the gears(1) Through Hardening(2) Case Hardening: (a) Carburizing, (b) Nitriding, (c) Carbo-Nitriding.(3) Surface Hardening: (a) Induction Hardening, (b) Flame Hardening.

Page 6: GEARS HEAT TREATMENT
Page 7: GEARS HEAT TREATMENT

Case Hardening Case Hardening produces a hard, wear resistance case or surface layer on the top of a ductile, shock resistance interior or core. The idea behind the case hardening is to keep the core of the gear tooth at a level around 30 to 40 HRC to avoid tooth breakage while hardening the outer surface to increase the pitting resistance Case hardening consists of three processes: (a) Carburizing; (b)Nitriding; (c) Carbo-Nitriding.

Page 8: GEARS HEAT TREATMENT

CarburizingCarburizing is a heat treatment process in which iron or steel is heated in the presence of another material which liberates carbon as it decomposes, at temperature between 850 and 950°C, at which austenite, with its high solubility for carbon, is the stable crystal structure. Hardening is accomplished when the high-carbon surface layer is quenched to form Martensite so that a high-carbon martensitic case with good wear and fatigue resistance is superimposed on a tough, low-carbon steel core.

Gears are almost always oil quenched because distortion must be held to the lowest possible level.

After case hardening, the hardness obtained lies in the range HRC 58 to 62 but in heavily loaded gears a minimum of HRC 60 is required.

Page 9: GEARS HEAT TREATMENT

Nitriding Nitriding is a surface-hardening heat treatment that introduces nitrogen into the surface of steel at a temperature range of 500 to 550°C, while it is in the ferrite condition.Because nitriding does not involve heating into the austenite phase field and a subsequent quench to form martensite, nitriding can be accomplished with a minimum of distortion and with excellent dimensional control. Nitriding is done to to obtain high surface hardness, increase wear resistance, improve fatigue life, improve corrosion resistance (except for stainless steels), obtain a surface that is resistant to the softening effect of heat at temperatures up to the nitriding temperature.

Page 10: GEARS HEAT TREATMENT

Carbo-Nitriding Carbonitriding is one of most common type of case hardening

processes for gears Carbonitriding is essentially a modified version of gas carburizing. The modification consists of bringing in ammonia into the gas

carburizing atmosphere. This adds nitrogen to the carburized case. The nitrogen gets diffused simultaneously into the steel along with

carbon. Generally a carbonitriding process is done at a lower temperature

and for a quicker span of time than that of gas carburizing. It has been found that after Carbo-Nitriding of Gears there has

been considerable improvement in useful life for many of the gears. Advantages for gears include temper resistance, heightened lubricity during cold start, better strength of the base metal in terms of tensile, yield and fatigue, an increase in throughput, also elimination of problems like quench cracking.

Page 11: GEARS HEAT TREATMENT

Surface Hardening This is a special hardening process in

which a particular surface of steel is made hard without altering the hardness of any other portion.

There are two types of surface hardening processes

1. Induction Hardening2. Flame Hardening

Page 12: GEARS HEAT TREATMENT

Induction Hardening Induction hardening is a heat treating technique that can be used to

selectively harden portions of a gear, such as the flanks, roots and tips of teeth, providing improved hardness, wear resistance, and contact fatigue strength without affecting the metallurgy of the core and other parts of the component that don’t require change.

Induction hardening does not require heating the whole gear. With induction, heating can be localized to only those areas in which metallurgical changes are required. For example, the flanks, roots and tips of gear teeth can be selectively hardened.

A major goal of induction gear hardening is to provide a finegrain martensitic layer on specific areas of the part.

External spur and helical gears, worm gears and internal gears, bevel gears, racks and sprockets are among the parts that are typically induction hardened.

Page 13: GEARS HEAT TREATMENT

Induction Hardening Machine

Laboratory Tribology UNDIP Semarang 2016

Page 14: GEARS HEAT TREATMENT

Induction Hardening Of Gears

Page 15: GEARS HEAT TREATMENT

Flame Hardening The flame hardening of gear teeth is a sound investment since it increases the life

of the gear by about 5 times. Flame hardening decreases both rolling friction and deformation.Generally there

are two methods of flame hardening gear teeth - spin hardening or progressive hardening.

With spin hardening all the teeth are heated & then quenched.  With progressive hardening individual tooth flanks are heated & quenched.

Flame hardening applies to most gear types - spur, helical, bevel, spiral bevel, herringbone and racks.

A wide variety of materials may be flame hardened including carbon and alloy steels, martensitic stainless steels and SG cast irons.  Generally steels with approximately 0.35-0.55 percent carbon are suitable for flame hardening.  Cast irons, higher carbon and higher alloy steels are susceptible to cracking & extra care should be taken to reduce this risk.

Page 16: GEARS HEAT TREATMENT

Flame Hardening In Gears

Flame hardening process in Gears

Page 17: GEARS HEAT TREATMENT