gettingstarted-3ddesign

8/10/2019 GettingStarted-3DDesign

1/36

Getting Started

Introduction to the Basics

Cadpipe Control Center

The Cadpipe Control Center provides a central location to organize your projects, settings and drawings.

For existing Industrial users, this will replace the Cadpipe Project Manager that you are familiar with.

Only the installed base will appear in the Control Center, so what you see on your screen may differ

slightly from the illustrated screen shots. Here we have all of the Cadpipe products installed.

Selecting the Cadpipe Control Center icon installed on your desktop, will give you something similar to

what you see here.

Highlighting the Cadpipe module that you are working with will give you the projects applicable to that

module. Projects are shared through the Industrial modules. For example, if you create a new project

for Industrial Pipe, that same project will be available for ISO and PID.

The installation will create the default project directory as specified in the installation procedure. That

will be CP_Gen2\cpwork, unless specified otherwise.


2/36

Adding New Projects

Select the New button under the Project Tools as shown.

You will see the following dialog. Enter your Project Name, as you want it to appear in the ControlCenter. You will then want to enter the folder where your drawings will be located, or use the Browse

button to search your system. You can set this folder anywhere accessible to your system. Here we will

simply place all drawings for this new project on your C: drive, but in production, this might be on a

network drive.

Enter, or Browse to, the location of

your project drawing directories.


3/36

In Industrial, the sub-directories, 3DDES, ISO, PID and CNCT will be created under the folder that you

specify.

You can also use this dialog box to set your Spec Folder which will set your database and spec locations

for this particular project. This is very useful if you want to have your specs and database tables located

on a network drive, ensuring that all users are working with the same information, or if you wishdifferent projects or clients to use different specs and database tables. In this instance, we will accept

the default location shown.

(If you do decide to move your specs to another location, you will need to manually copy the cptable (or

cpmtable) folder to that location, from the default installation under CP_Gen2, or from wherever you

have this folder currently.)

In the same fashion, you can add a unique location for the Spool drawings for each project. Selecting

Add Spool, you can enter the path you require. Here for example, we have set the Spools Folder to a

Spools directory under the Client1 directory.

You can add a location for your specs

and databases, or accept the default

as shown here.

You can add a location for your spools

if required.


4/36

Also note that you can add sub-Projects in almost exactly the same way. Check the Add as Subproject

button when adding these, and they will be placed under your highlighted project directory.

The Modify button under your Project Tools will give you the same dialog box, so you can use this to edit

projects that you have already created when necessary. (Right click will also invoke this dialog box for

the highlighted project.)

Hover over any project, and a tooltip will appear, displaying all of the pertinent information for that

project. Similar to what you see above. Right clicking that project will bring up the Modify Project

dialog box, allowing you to edit any of these settings.

Please refer to our website for complete documentation on the Control Center.

Drawings

Right click over the drawing area, and youll see the File Operations dialog. Use this to create a new

drawing file. You will also find this dialog under the Utilities pulldown.


5/36

Selecting Add Desc , or add description, from the dwg utilities dialog box will allow you to enter any

informative text, which will appear in your drawing list.

Here we will create a drawing named Example 1, adding a description to that drawing of Building 4

Area 101.

Enter your required Drawing name

Browse to your required prototype. The

default Cadpipe prototype dwg will be

listed; in this case a blank 3ddes.dwg

located in the cpacadw directory. Using

the Browse Prototypes button, you can

select any drawing file.

See the Available options listed. The Move and

Copy options will open a Browse window.

Here we will select the Create option.


6/36

You should see results similar to these.

Double click the drawing name, or highlight it and select Launch. This will open AutoCad and load

Cadpipe.

You should see the dialog box below, which confirms that Cadpipe is loaded.

Once Cadpipe is loaded, please set up your AutoCAD screen to your preferences. For example, you

may want to dock your toolbars, set your units of preference etc.


7/36

Cadpipe Options

Before you get started, you may want to look at a couple of general settings.

Options

On the first Tab of this dialog box, are some general Current Run Settings. The only one to really

concern yourself with here, is the Default Pipe length. Out of the box, you will see that it is set to 10.

You will most likely want to change that to 20. (6100mm).

This sets the maximum pipe length that you can place without a weld. Longer lengths will be placed in 2

or more pieces

.

You will also want to decide on the layering scheme that you require. The default layering scheme will

place all pipe and fittings on a fittings layer. You can select Layers by Spec, Process, or in this case set

to Layers by Line Number.

Further layer modifications are available in more advanced documentation.

You can find the Cadpipe Options

command on your toolbar as illustrated,

under the 3DDesign pulldown, or on the

CP Pipe ribbon tab.


8/36

Weld settings, as well as your tooltips are also here to be modified to suit. These can be changed at any

time, so it is not necessary to set up prior to starting your drawing.

(Note: If you do decide to show your welds at a later date, you can select the Add Missing button to

show the welds on any previously placed piping.)

Options Manager

The Cadpipe Options Manager allows you to use a floating dialog box to

access often used commands. You will find a toggle for this dialog on the

CP Pipe ribbon tab, the Design Toolbar as shown, or under the 3DDesign

pulldown menu.

Note: The Show Join Point Icon toggle is also here. The Join Point

Indicator makes sure that you always know graphically where your join point

is when Autofit is toggled on.


9/36

Cadpipe Specifications

Specifications

This dialog box shows you all of your current settings. That is, all of the parameters that define the pipe

or fittings that you are going to place. ie Pipe size, schedule, rating etc. It is available on the Design

toolbar as illustrated, under the 3DDesign pulldown menu, or on the CP Pipe ribbon tab.

The first thing that you will want to look at here is the Line Designation. Set your line number to whatever

you like. (P-101 used here) Do not include the pipe size in the line number this will only cause

duplication.

Cadpipe comes equipped with many example piping specifications. Obviously, you would set up your

own, perhaps initially by copying one of our supplied samples and renaming that. For this purpose

though, we will set to C12A which is a supplied, generic 150# CS spec. Further information on

customizing piping specs will be discussed later.


10/36

For now, set your spec to C12A. You will see a spec check button. When that is turned on, you will see

all the settings below become deactivated. The spec controls the schedules, ratings etc. If you want to

change any of these, you can turn spec check off, and it is all activated again.

Set your Spec Alternate button on as well. This will give you options including all items within the spec,rather than the defaults only.

The spec override button disables spec check for one placement, and is also available on the placement

dialog boxes

For example, with C12A, spec on change your pipe size from 1 to 6 (25-150mm), and youll see the

settings in the dialog box change. This spec is SW small bore, and BW 150# large bore.

While it is not required to use piping specs at all, it is recommended. Well use C12A in this example, but

feel free to use another if you prefer. A brief description of our generic supplied specs follows. On

evaluation installations, only the ANSI Plus database is installed, so you will want to limit your selection to

one of those. All listed use the AP database unless otherwise noted.


11/36

For your information....

Summary of Supplied Example Specs : All use the ANSI Plus database unless otherwise noted.

AAA1 300# CS

ABB1 300# CS / THRD Small Bore

C12A 150# CS

C12LJ 150# CS, Lap Joint Flanges

C32A 300# CS

C62A 600# CS

C92A 900# CS

CA2B 1500# CS

CB2B 2500# CS

CL-001 600# Clamped

F-LINED 150# CS Lined

FLGD 150# CS Flanged

FRP1 150# Fibercast (Plastics db)

FRP2 150# FRP Lapped (Plastics db)

PVC 150# PVC (Plastics db)

S11C 150# 304 SS (AP db)

S11D 150# 304L SS (AP db)

S11E 150# 316 SS (AP db)

S11F 150# 316L SS (AP db)

S11LJ 150# 304 SS Lap Joint (SS db)

S31C 300# 304 SS (AP db)

S31D 300# 304L SS (AP db)

S31E 300# 316 SS (AP db)

S31F 300# 316L SS (AP db)

S61C 600# 304 SS (AP db)

S61D 600# 304L SS (AP db)

S61E 600# 316 SS (AP db)

S61F 600# 316L SS (AP db)

Depending on your installation, you may also see supplied example specs from the DIN or BS databases.


12/36

Equipment

Cadpipe supplies a basic equipment generator, where you can create and modify vessels, pumps and

exchangers. The vessel generator will allow you to Build different kinds of equipment.

For example, lets place a pump, then a vessel in your empty drawing. Again, we are assuming that you have

Cadpipe loaded, and your AutoCAD settings to your preferences.

Equipment is available from your pulldowns, under Equip, from the Place toolbar, or on the CP Pipe Ribbon Tab..

Select Pump. You will see the following dialog box, with generic pump types. In this case, select Centrifugal.

Youll see the dialog box below, where you can specify different parameters for your pump. Fill in data such as

the base elevation, dimensional data, and suction and discharge nozzle information. In this instance, we will

accept most of the defaults, but do select the End type information as shown to input the nozzle information for

your pump. In this case, set each nozzle to RF, 150# with a 1/8 gasket (3mm).

You can save your pump or other equipment configurations to be used again in this or other drawing files.


13/36


14/36

Next, lets place a vessel. As this is simply an example, you can use the dimensional information below, or select

your own. In this instance, we have just added 2 nozzles to our vertical vessel. Obviously, there will be others,

but we can add those later using the Modify button at the bottom of the vessel generator dialog box.


15/36


16/36

Commands to remember..

Start a Run

Start a run is available on the Design toolbar as shown, under the 3ddesign pulldown, on the CP Pipe ribbon tab,

on the Options manager, or at the bottom of the specifications dialog box. This command allows you to choose a

starting point, line, number, elevation and direction. You will begin placing fittings once you have set this starting

point.

Join To

The Join to command allows you to select an existing fitting, nozzle or other cadpipe item, and resets your

settings to match the fitting chosen. This command moves the start point and placement direction, pipe size, line

designation, etc

Join to is available on the toolbar as shown, under the 3ddesign pulldown, on the CP Pipe ribbon tab, on the

Options Manager, or again at the bottom of the specifications dialog box.

Undo Back

The Cadpipe Undo command will undo the entire last Cadpipe item. Use this rather than AutoCADs Undo when

working with Cadpipe commands.

It is located on the Edit toolbar as illustrated, and also under the 3DDesign pulldown, or under any of the Cadpipe

Ribbon tabs.

Start a run

Join To


17/36

Drawing without a routing line

Start with the drawing with the 2 pieces of equipment that we just created. We should still be set to a line number

of your choice, (P-101) and the c12a spec. Make sure that your spec check is activated.

Join to. Select the nozzle on the vertical vessel. You want to make sure that you digitize the nozzle itself, not

the gasket. This will set your pipe size to 8 (200mm), and your starting elevation.


18/36

If you are asked if you want auto-fit on, accept that. Auto-fit keeps your starting point current in any fitting to fitting

configurations. Toggle auto-fit off, and you will be prompted for each placement location and rotation angle.

Place a flange. Because you have autofit on, and spec check, you do not need to worry about any of the settings

or the insertion point. Flange placement is available on the Fittings toolbar as shown, under the Place >> Flange

pulldown, or on the CP Pipe Ribbon tab.


19/36

AutoRouting

The Auto-Routing feature allows you to easily, dynamically and accurately route your piping, without having to

individually select each fitting. You will find this command on the CP Pipe Ribbon tab, the Design toolbar, or

under the 3DDesign pulldown menu.

A compass will appear, in all views, at your current vertex while you are in the Auto-Route command, and will only

allow you to drag your cursor in a direction that will allow the current fitting type that youve selected. Your current

Ortho mode (F8) will also impact where you can drag the cursor. You will see the fitting type appear in the tooltip

as shown.

At this point, you can digitize your length, by selecting a point or by watching the length as it appears in the tooltip,

or you can simply type in your required length, dragging the cusor in the required direction. You will notice that,

for ease of use, the length increments in the tooltip are 6 (or 50mm if metric). Holding down the Shift key will

decrease those increments to 1 (or 10mm if metric). Lengths are calculated vertex to vertex, or to the corner of

your bend. The actual length of pipe placed will be calculated to accommodate the fitting lengths.

While details on the AutoRoute command are discussed in another document available on the website, for now

just route a pipe length similar to the drawing below.


20/36

Place an additional flange as shown. Again, you do not have to select an insertion point.


21/36

For the next line, you may want to set your line number to something else, or not.

Here, weve set to P-107, but left the spec etc the same as before. (C12A) Join to the suction nozzle of your

pump. Place mating flange there as well.

Then we will place an eccentric reducer against the flange.

Reducers are located on the Fittings toolbar as shown, under the Place >> Fittings pulldown, or under the CP

Pipe Ribbon Tab.


22/36

After selecting the eccentric reducer, youwill be prompted for the outlet size.

Here we will select 8 (200mm), so place

a 6x8 (150x200)

Then you will be prompted for the

orientation. Here we have chosen FOT

(flat on top)


23/36

Then well place a gate valve. Valves are located on the toolbar as shown, under the Place >> Valves pulldown,

or on the CP Pipe Ribbon Tab.

Selecting this will bring up the Valve placement dialog box, and we will accept the spec defaults. So choose gate,

and place.

Because your spec check is on, modification to the rating, type etc will be inactive. If it is not on, you will want to

ensure that the valve type ie regular pattern and unspecified manufacturer is set.

Immediately following placement, the dialog box for the rotation of the handwheel will appear.

Enter or right click will accept the default, or select the rotation required.

Selecting another command will also accept the default shown.

Insert Fitting.

To use the insert fitting command, you will want to Join to the pipe that we will be inserting into. This ensures that

your settings are correct for the fitting to be placed. It doesnt really matter where on this pipe you select.


24/36

Here we will insert a tee on the main line, aligned with the valve on the pump. The insert fitting command is

located on the Fittings toolbar as shown, under the 3DDesign pulldown, or on the CP Pipe Ribbon Tab.

Select Aligned in the Insertion Justification dialog box

Select Tee as shown.


25/36

You will see the following prompt on the command line.

Pick Pipe/Fitting to Align with:

Digitize the flange on the outlet of the valve at the pump. You will be prompted for the line designation of the

branch of the tee to be placed. Here we have changed the line number to p-107.

You will be asked for the rotation angle of the tee. Select 270

You should now see a tee, placed in your main pipe run, branch down. If you are uncertain as to the rotation

angle to select, watch your drawing, as the tee will be shown in each orientation.

To connect this: Use the Join to command, selecting the branch outlet of the tee (probably in an iso view). Then

choose the AutoRouting command, then J, for Join, selecting the flange on the valve at the pump.

You should see something similar to this.


26/36

Return to Accept this route.

Hover over any of your fittings, and you will see the tooltip, letting you know what this fitting is as shown. You

can modify these tooltips in your Cadpipe Options, as mentioned earlier in this document, to ensure that theinformation that you want to see is listed.

Join to selecting the branch of this tee

AutoRouting, and use the Join option to

connect to this flange.


27/36

You can also use the Cadpipe Query command for details on any of the Cadpipe items. Query will also allow you

to place text on your model etc. Query can be found on the toolbar as shown, under the Tools pulldown, the CP

Pipe Ribbon Tab, Right click menu, or by double clicking the item.

Drawing Pipe with a Routing Line

The Cadpipe Routing line is an intelligent and powerful 3D polyline, and can be used to route the centerline of

your pipe. Normal drawing practices will most likely see you using a combination of with and without the routing

line. The routing line also gives you the ability to use other commands, like auto-elbow, auto-pipe and several

additional editing capabilities. Items placed on this routing line will adopt its intelligence ie the line number and

piping spec. The routing line itself is a non-plotting entity.

You may find it easier to use the routing line command when you have complex piping situations, rolled piping or

offsets, sloping lines, lines where elbows need to be trimmed etc.

The Routing Line command is located on the Design toolbar as shown, under the Place pulldown, or on the CP

Pipe Ribbon Tab.

To start, we will just create a simple routing line to illustrate its use. You can set your line designation on the

command line within the routing line command, or by using the Cadpipe Specifications dialog box.

On the command line you will see options that are similar to those of the AutoCAD 3dpolyline command.

Type Dfor example, to change your line designation. Here we will set that to P-112, and C12A.

Then type Efor elevation. Now we can digitize an elevation, or enter a value. Here for example, select the node

at the face of the gasket on the other nozzle that we placed on our vessel as shown.


28/36

Now you can start to route your pipeline.

Digitize the first point, ie at the node of the nozzle again. Then, dragging the line south 3 (900mm), then enter E

for an elevation drop of 6 (1825mm), type -6, drag east 10(3050mm), then E for another elevation change,

digitizing the existing pipe run to set to that elevation. Continue the line as shown. You can do this all in any view.

You can type a specified elevation or use + or for your elevation change.

As this is just an example, the dimensions given are approximate. Please use whatever you wish. You can type

coordinates, enter specific distances, or digitize anything that you wish to reference. Using AutoCADs osnaps

will make it all easier and more precise.

Much more information regarding the Cadpipe routing line is available in other documentation.

Join to the nozzle, and place a gate valve. Notice that with AutoFit on, the insertion point of the valve, as well as

the configuration, is set correctly with 1 flange, and the insertion at the valve face.


29/36

Auto Elbow

You will find the AutoElbow command on the CP Pipe Ribbon tab, under the 3DDesign pulldown, or on the

Design toolbar as shown.

You will be shown a dialog box to select your elbow type here we select LR.

You can select the routing line at any location and return for the entire line. (Or you could select a start and end

point to only place elbows on a section of your line.)


30/36

Place Fittings

Lets just place a straight tee on the lower section as shown. As AutoFit is off, you will see that the nearest osnap

is active. Use that in this instance, and digitize on the routing line. You will be prompted for the angle of

placement, branch, and branch line designation. We will leave the branch line number the same as your main

run. You again can simply drag the rotation angle into place.

Then we will place an 8x6 concentric reducer as illustrated. Notice on your status line, that your current pipe size

has changed to 6.

Place a 6flange at the end of your routing line. Have your insertion point set to the face of the flange.


31/36

AutoPipe

The AutoPipe command can be found on the 3DDesign pulldown, on the CP Pipe Ribbon Tab, or on the Design

toolbar as shown.

Selecting anywhere on the routing line, then return, will complete this line. (Again, you can select only a start and

end point to pipe if required.)

Notice that the pipe size changes as required.

Then, just to finish off this line, Join to the branch outlet of the straight tee. Place a flange, then a blind flange.

When prompted for AutoFit On, accept.

Please, work in any view that you are comfortable in.


32/36

You should end up with something similar to the screen shot below.


33/36

Automat ic BOM

Cadpipes Bill of Materials can extract your material list into several different formats, depending on your specific

requirements. (ie: excel, access, ascii, display, to printer, or to the drawing.) You can extract material

information from a single drawing file, or from an entire project.

Material descriptions and user codes or part numbers are read in from your piping specifications, so can be as

simple or detailed as you require. More information on this is included in the documentation on Cadpipe Specs.

The Auto BOM command is found on the Cadpipe Tools pulldown, on the CPTools ribbon tab, or on the Reporting

toolbar as shown.

Selecting the AutoBOM icon, will bring up the dialog box above.

If you did want to place the material listing on your drawing, notice that the Drawing BOM Sort Order options

become available in this dialog. A BOM formatting Utility is available on your menu to customize the BOM on the

drawing. You will find more information on the formatting utility in subsequent documentation.

Use the CDF option to export the bom report into excel.

As here we will simply run a report to our display, select Process BOM in the above dialog box.


34/36

As we selected the report, you should see an additional dialog box with reporting options. (sorting, output etc)

Also note that you can include or exclude Revision information, Long descriptions or weight. Here, check Include

Long Desc., then OK

In this instance, you bom will appear on your screen, complete with the material descriptions from your piping

specifications.


35/36

UDE Out

Universal Data Exchange files (UDE), is the format that Cadpipe Industrial Piping uses to import or export lines

into the 3D or the Iso module for fabrication isometrics, stress isos etc. The UDE Out command is located underthe 3DDesign pulldown, on the Utilities toolbar as shown, or on the CP Tools Ribbon Tab.

These files can be created by line number, runs, or by selecting the fittings directly.

Here we will choose the Selected Runs options. Choose Add, then select the run, enter, then save. You should

see the selected run highlight, which lets you know what has been chosen. Notice that using the Selected Runs

Option does include branches, regardless of their actual line designation.

Save each run individually, for separate isometrics. The line number of the selected item will be the default udefile name which in turn will be the default name of your generated isometric. Obviously, you can modify those

as required, but you would likely want to do that during this process.

The iso module will expect the line to be continuous.


36/36

We will then repeat this process, selecting the other line.

Here you will most likely end up with 2 ude files P-101-1, and P-112-1.

See the Cadpipe Iso Getting Started document for isometric generation.

Potential Issues

Note: If, for some reason you do not see this dialog box when you first enter the drawing, it is most likely that the

Cadpipe module is not loaded. In this case, please confirm that the cp_gen2_3\cpacadw directory is included in

your support file search path within the AutoCAD options command. There are some AutoCAD installations that

are not automatically reading the Autodesk switches particularly if you are using any of the Autodesk

Mechanical installations.

Note: If you wish to use the pulldowns and they do not appear set menubar to 1 at the command line

gettingstarted-3ddesign

Documents