Thank you for purchasing the ProMediaGear Katana Heavy Duty Gimbal Head.The GK, Katana Gimbal was designed to effectively balance your telephoto lens and camera for horizontal and vertical panning. Our robust design, featuring precision engineering will allow effortless control of your lens. Shoot with confidence.

#GK Specifications:

Length............................................................................ 10.50 inches (267mm)

Width.....................................3 inches (76mm) 4.30 inches (109mm) with knob

Height .................................................................................13 inches (330mm)

Weight............................................................................... 5.58 pounds / 2531g

Load Capacity...................................................................... 150 pounds / 68 kg

Tripod Mount....................................................................................................... 3/8-16

16555 108th Ave, Orland Park, IL 60467 USA1-708-263-4443 • Toll Free: 1-888-413-3332 • www.ProMediaGear.com

#GK, Katana Gimbal Head

Setup:

1. To mount the GK Katana onto a tripod begin by rotating the Base Plate (G) clockwise on the 3/8 inch mounting screw of the tripod. Next, lock the pan knob (F) then using the leverage from the GK Katana, tighten a bit more until snug.2. Open the Arca Compatible Clamp (C) by loosening the Clamp Knob (D) and insert you lens/camera plate onto clamp. Lock Clamp Knob (D) securely.

Balancing Camera/Lens:

3. While holding the camera and lens with a light touch loosen Tilt Lock Knob (A) so the arm is free to swing and also slightly loosening Clamp Knob (D). Now you will be able to slide your camera and lens plate forward or backward in the clamp unitl the lens is perfectly horizontal and not drooping. Once neutral balance is found remember to lock the Clamp Knob (D) securely. You may also set your resistance on Tilt Lock Knob (A) a. If the Lens is pointing DOWN, loosen the Clamp knob (D) and move camera/lens backwards. Set resistance on Tilt Lock Knob (A) when complete. b. If the Lens is pointing UP, slightly loosen the Clamp Knob (D) and move camera/ lens forward. Set resistance on Tilt Lock Knob (A) when complete.4. After balancing your lens you may set the vertical position to allow the lens to stay pointed wherever you aim in a perfect balanced nodal position if desired. Start by loosening the Vertical Arm Clamp Knob (E) and raising the clamp up or down to find the proper balance point. This is typically achieved when the center of the tilt bearing is even with the center of your lens barrell. When done correctly the lens will stay at any position you point it to without drooping and remain properly balanced on your gimbal. Find the position that best fits your shooting style. Happy Shooting!

Instructions

F. Pan Lock Knob

G. Base Plate

A. Tilt Lock Knob

E. Cradle Clamp Knob

D. Clamp Knob

C. Arca Compatible Clamp

B. Arca Compatible Vertical Arm

Features

• Smooth pan and tilt locking mechanism ( separate from assembly mounts )

• Arca compatible lens mount

• CNC Precision Machined from T6061 aluminum

• Sealed Ball Bearings

• Hard anodized scratch resistant finish

• Made in USA

• 5-year warranty

Maintenance

Check before every use for any loose screws/parts and tighten with knob or supplied hardware. The bearings are sealed and require no lubrication. A small amount of oil (WD40 or similar) may be used on the knobs if necessary. Caution should be taken that it is not exposed to potentially corrosive environments. Taking these precautions will greatly extend the life of the product.

34mm and 42mmPro STIX Tripods

#GF2Flash Doubler

Accessories

#GKJr.Katana Gimbal (HD)

#HM1 Monopod Tilt Head

#SS2Quick Release Strap

#BH1 Ball Head

#PX44.5" Lens Balance Plate

#PX66" Lens Balance Plate

#PXC1Arca Rail w/ Clamp

16555 108th Ave, Orland Park, IL 604671-708-263-4443 • Toll Free: 1-888-413-3332 • www.ProMediaGear.com

rev 11/17