globe nemesis drivetest methodology_v3

HUAWEI TECHNOLOGIES CO., LTD.

February 2012

GLOBE NEMESIS PROJECTDRIVETEST METHODOLOGY

HISILICON SEMICONDUCTORHUAWEI TECHNOLOGIES CO., LTD.

DRIVETEST TEST PROCEDURES


1. OVERVIEW OF GLOBE NEMESIS PROJECT

Based on GLOBE NEMESIS project, Drive Testing shall be conducted as follow:

2G/3G Pre Drive Testing (Cluster Level)

2G/3G SSV (Single Site Verification)

2G/3G Post Drive Testing (Cluster Level)

2G Cluster Acceptance (Cluster Level)

3G Cluster Acceptance (Cluster Level)

Documents Output for Acceptance

Pre Benchmarking Report- Initial

SSV Report

Pre/Post Benchmarking Report

Cluster Acceptance Report


RF Acceptance Process

Page 4

SWAP

• 2G/3G Cluster Pre DT

• SSV DT • Site

Optimization

• 2G/3G Post DT• Cluster Optimization

• 2G Cluster DT• 2G Cluster

Optimization

2G/3G SSV Report

2G/3G LBL Benchmarking

Report

2G Cluster Acceptance Report

3G Cluster Acceptance Report

•100% Cluster Swap

2 week Pre OSS Statistic

1 week Post OSS Statistic

• 3G Cluster DT• 3G Cluster

Optimization

•2G Expansion

•HSPA + Activation

•3G Expansion

•New 3G Collocation

•New 2G Collocation

TRANSPORT DEPENDENCIES

1 Week

1 Week Post OSS Statistic

4 Day

1 Week


4 Day

1 Week


4 Day

•Frequency Re-Farming


2. TOOLS AND MANPOWER REQUIREMENTS

Hardware Description

Laptop Computer 1.6GHz or better CPU speed. At least 768MB RAM and 30GB HDD. One for each team.

GPS Receiver A GPS Receiver is used to provide positioning data for the Drive Test tool. At least one per test vehicle. Each GPS receiver shall have an external antenna.

GSM/UMTS UE's Compatible with TEMS /PROBEData Dongle (2G/3G with HSPA 7.2MB) Used for Data download and Upload (HSPA+/ HSDPA)

AC/DC Portable Converter DC power to the equipment in the RF Kit for each phone. An inverter to supply AC power to the laptop computers.

Drive Test Measurement Tools TEMS Investigation V9 & Above for 2G/3G & V.13 with HSPA/LTE) capabilitiesDT Vehicle Saloon or 4wd

Software Description

Speed Test Software (DU METER) Software or freewareTEMS Investigation with license Dongle TEMS Investigation V9 & Above for 2G/3G & V.13 with HSPA/LTE) capabilities

Mapinfo for coverage plotting purposesTEMS Cell Files HT/Subcon to prepare the cell files before DT activityHUAWEI PROBE Software for MOS quality voice Test

Manpower Description

TEMS Operator Operator must have deep knowledge of operating TEMS & post processing dataDriver Skilled driver with routing knowledge

Others Description

SIM Cards (CS & PS) Test SIM should be a P1 type

FTP Server TBDTest Number Any phone placed inside the Car (same network); Test Number should place Near the DT Engineer

GT Plots Legend Agreed by Both Parties ( GT, NPM, HT)


3. GENERAL DT GUIDELINES

General DT guideline to be adhere during all DT activity

During Pre/Post Cluster level DT, minimum number of calls sample must be achieved but calls shall continue until DT route completed.

The pre and post drive test coverage shall follow the same driven route.

The pre and post drive test should be performed outside the maintenance window and on the same time period (morning on morning,

afternoon on afternoon, evening on evening).

The post drive test samples should be within + or - 5% of the pre drive test samples.

Maximum vehicle speed (<50km/h)

TEMS UE’s to placed on the vehicle dashboard

GPS external antenna shall be placed on the vehicle rooftop

PROBE for voice quality MOS will used during Cluster Acceptance.

Scanner shall be used during cluster acceptance instead of UE’s

Using Actix Post processing tools, “Location binning” should be used in the post processing of drive test log files.

Naming of logfile: for Cluster ( Subcon_TeamXX_Area_clustername_Date) ; for SSV (Subcon_TeamXX_Area_sitename_Date).


4. KPI’s COUNTER VS DT TEST

2G Test Item

KPI CS Drivetest Measurement Method Pre-Benchmark SSV Post-Benchmark Cluster Acceptance

2G RxLev (dBm) >= -64 (CBD Metro) Drive test ◎ ◎ ◎ ◎

2G RxQual (Class) <= 4 Drive test ◎ ◎ ◎ ◎

Voice CSSR Drive test ◎ ◎ ◎ ◎

Voice Quality MOS Drive test ◎

Voice DCR Drive test ◎ ◎ ◎ ◎

SMS MO and MT Successful Rate Drive test ◎

Average Ping RTT Drive test ◎

Hard Handover Successful Rate Drive test ◎ ◎ ◎

KPI PS Drivetest Measurement Method Pre-Benchmark SSV Post-Benchmark Cluster Acceptance

Average DL Throughput via DT Drive test ◎ ◎ ◎

Average UL Throughput via DT Drive test ◎

Average DL Throughput measured via Stationary Test per cell Stationary Test ◎ ◎

Average UL Throughput measured via Stationary Test per cell Stationary Test ◎ ◎

4.1. 2G KPI VS. DT TEST


3G Test Item

KPI CS Drivetest Measurement Method Pre-Benchmark SSV Post-Benchmark Cluster Acceptance

3G CPICH RSCP (dBm) >= -75 (CBD Metro) Drive test ◎ ◎ ◎ ◎3G CPICH Ec/No (dB) >= -10 Drive test ◎ ◎ ◎ ◎

Voice CSSR Drive test ◎ ◎ ◎ ◎Voice Quality MOS Drive test ◎

Voice DCR Drive test ◎ ◎ ◎ ◎SMS MO and MT Successful Rate Drive test ◎

Average Ping RTT Drive test ◎Hard Handover Successful Rate Drive test ◎HSDPA Call Setup Success Rate Drive test ◎ ◎ ◎ ◎

HSDPA Call Setup Time Drive test ◎ ◎ ◎ ◎HSDPA Drop Rate Drive test ◎ ◎ ◎ ◎

3G Soft Handover Rate Drive test ◎ ◎ ◎Soft Handover Successful Rate (RT and NRT) Drive test ◎ ◎ ◎ ◎

KPI PS Drivetest Measurement Method Pre-Benchmark SSV Post-Benchmark Cluster Acceptance

Average DL Throughput via DT Drive test ◎ ◎ ◎ ◎Average UL Throughput via DT Drive test ◎

Average DL Throughput measured via Stationary Test per cell Stationary Test ◎ ◎Average DL Throughput measured via Stationary Test per cell Stationary Test ◎ ◎

Dual Mode Drivetest Measurement Method Pre-Benchmark SSV Post-Benchmark Cluster Acceptance

Voice CSSR Drive test ◎ ◎ ◎Voice Quality MOS Drive test ◎

Voice DCR Drive test ◎ ◎ ◎ISHO (3G to 2G) Successful Rate RT Drive test ◎ ◎ ◎

ISHO (3G to 2G) Successful Rate NRT Drive test ◎Time on 3G based on the Voice Call Test Drive test ◎ ◎ ◎

4.2. 3G KPI VS. DT TEST


5.1 PRE DT (CLUSTER LEVEL) Guideline

Guidelines covers both technology Shall cover all sites within swap cluster until 1 layer neighbor at adjacent cluster Test are purely mobility For 3G testing, when 3G handover to 2G, stop the car and terminate the call and data collection. Wait for the test phone perform reselect to camp to 3G again, and then

that the time to start recording again. This scenario is case to case basis, particularly in areas ( in particular in rural areas) with no 3G neighbors or signal is very poor compared to 2G neighbor. Also in areas with no 3G site intended to cover the areas with DT routes.

Outputs Original log files to be surrendered to HT per site basis and Cluster Basis Sub con to provide pre DT reports to HT for approval & analysis

Test Methods

UE SET-UP TECHNOLOGY TEST EQUIPMENT TEST TYPE TEST METHOD CALL DURATION(s) IDLE MODE(s) B NUMBER/ FTP SERVER SAMPLE

MS1 2G-SHORTCALL TEMS UE’s CS CALL MOBILITY 45 15 B: Any phone placed inside the car (same network)

50(minimum); must complete the DT route

MS2 2G-LONGCALL TEMS UE's CS MOBILITY 999999 NR B: Any phone placed inside the car (same network) LONG CALL

MS3 2G-IDLE TEMS UE’s IDLE MODE MOBILITY NR NR NR NR

MS4 2G (GPRS/EDGE) TEMS UE's PS-DL MOBILITY DL-3MB 10sec. FTP: NR




MS2 3G/2G DUAL MODE TEMS UE's CS CALL MOBILITY 999999 NR B: Any phone placed inside the car

(same network) LONG CALL

MS3 3G HSDPA DONGLE/DATA CARD PS-DL MOBILITY DL-125M FTP 10sec. FTP: NR

2G

3G

5. DRIVETEST METHODOLOGY


5.2. SSV DT (Site Level)

Guidelines

Guidelines covers both technology after Swap.

Drive test to be conducted immediately after swap (on the same day) to check for possible Swap Sector. When Swap sector detected; immediately informed

concerned Team for swap sector rectification ( HT region In charge).

Need to check the actual parameters based on as defined in SSV report requirements during and after Drive test.

Need to check the Intra cell handover (clockwise & counter clockwise if applicable for road is passable) as defined in SSV report requirements.

DT route should be able to have a HO attempt to the next neighboring site.

DT route should be able to have a Cluster border sites have a HO attempt to the next neighboring site from the next adjacent Cluster( if applicable only).

Shall cover all sector of the tested site.

Test include stationary & mobility.

Need to test 2G-3G idle/PS cell reselection test in 2G SSV. Applicable if there’s 3G neighbor sites. Update as of September 11, 2012

Need to test 3G-2G idle/PS cell reselection test in 3G SSV if applicable. Applicable if there’s 2G neighbor sites. Update as of September 11, 2012

Outputs

Original log files to be surrendered to HT per site basis on a CD/DVD disc Sub con to provide 2G & 3G SSV reports to HT for approval & analysis

5.2.1. SSV TEST-OUTDOOR SITE


STATIONARY TEST

TEST NO. UE SET-UP FUNCTIONALITY TEST TECHNOLOGY TEST EQUIPMENT TEST TYPE SAMPLES COMPLETION

1 MS1-DL DL FILESIZE: 3MB 2G TEMS UE's PS 2(minimum) Screenshot after 1 minute DL

2 MS1-UL UL FILESIZE:1MB 2G TEMS UE's PS 2(minimum) Screenshot after 1 minute UL

Test Method

MOBILITY TEST

UE SET-UP TECHNOLOGY Purpose(s)

TEST EQUIPMEN

TTEST TYPE

CALL DURATION(s

)IDLE MODE(s) B NUMBER SAMPLE

MS1 2G SHORTCALL UNLOCK BCCH

Unlock the BCCH in TEMS’s UE test phone/ TEMS software to check dominant cells during In-call both for G900 & DCS1800 Mobility Coverage checking , Call checking, and Handover checking both for G900 & DCS1800

TEMS UE’s CS 45 15B: Any phone placed inside the car (same

network) 30(minimum)

MS2 2G-IDLE MODE Lock BCCH Lock BCCH in TEMS’s UE test phone /TEMS software of cells of the site need to to test for coverage extend check after swap and for better swap sector checking in Mobility TEMS UE's CS NR NR N/A NR

For Data Testing DL & UL of data should be test with minimum of 2 samples each cell in 1 minute duration. DUMETER will be used in measuring average throughput each test. Screenshots are needed for each samples when time reaches 1 minute in DU meter stopwatch during Download and Upload.

2G

MOBILITY TEST – 2G-3G idle/PS cell reselection test. Update September 11, 2012

UE SET-UP TECHNOLOGY PURPOSE(s) TEST EQUIPMENT TEST TYPE SAMPLE(s)

MS1 2G-IDLE MODE Cell Reselection test 2G-3G idle/PS. Each sector shall perform cell reselection test to its neighboring 3G site after swap. TEMS UE's Idle/PS Cell reselection NR


MOBILITY

UE SET-UP TECHNOLOGY Purpose(s)

TEST EQUIPMEN

TTEST TYPE

CALL DURATION(s)/ DOWNLOAD

SIZEIDLE MODE(s) B NUMBER/ FTP

DL SAMPLE

MS13G SHORTCALL UNLOCK

Scrambling Code Unlock the Scrambling Code in TEMS’s UE test phone/TEMS software to check dominant cells during In-call in 3G Mobility Coverage checking , Call checking, and Handover checking in 3G in Mobility

TEMS UE’s CS 45 15 B: 30(minimum)

MS2 3G-DEDICATED LOCK Scrambling Code

Lock the Scrambling Code in TEMS’s UE test phone/TEMS software of all cells of the site need to test for coverage extend check after swap and for better swap sector checking TEMS UE's CS 99999 NR B: NR

MS3 3G (HSDPA) HSDPA Download speed checking and measurement of the site after swap in Mobility DONGLE/TEMS UE’s PS 125MB 10 FTP : NR

STATIONARY TEST

TEST NO. UE SET-UP FUNCTIONALITY TEST TECHNOLOGY TEST EQUIPMENT TEST TYPE TEST METHOD SAMPLES COMPLETION

1 MS1-DL HSDPA-125MB 3G DONGLE PS STATIONARY 2(minimum) 1 min Download each samples

2 MS1-UL HSDPA-50MB 3G DONGLE PS STATIONARY 2(minimum) 1 min Download each samples

3G

MOBILITY TEST – 3G-2G idle/PS cell reselection test. Update September 11, 2012

UE SET-UP TECHNOLOGY PURPOSE(s) TEST EQUIPMENT TEST TYPE SAMPLE(s)

MS1 3G-IDLE MODE Cell Reselection test 3G-2G idle/PS. Each sector shall perform cell reselection test to its neighboring 2G site after swap. TEMS UE's Idle/PS Cell reselection NR


5.2.1. SSV TEST-IBS SITE

TEST NO. UE SET-UP FUNCTIONALITY TEST TEST EQUIPMENT TEST TYPE TEST METHOD SAMPLES COMPLETION

1 MS1-MO VOICE CALL MO & MT TEMS UE's CS STATIONARY Minimum of 2 samples 100%

2 MS1-MO MMS MO & MT TEMS UE's PS STATIONARY Minimum of 2 samples 100%

3 MS1-MO SMS MO & MT TEMS UE's PS STATIONARY Minimum of 2 samples 100%

4 MS1-DL 2G E(GPRS) FTP 3MB DL TEMS UE's PS STATIONARY Minimum of 2

samples -

5 MS1-UL 2G E(GPRS) FTP 1MB UL TEMS UE's PS STATIONARY Minimum of 2

samples -

TEST1. Stationary Test/ Functionality Test SSV needs to be conducted 2 points (wherever accessible) below 2 different antenna points and 1 point (wherever accessible) 10 meters from the

antenna point, to verify there is no coverage or performance degradation after swap and execute all other SSV tests. Monitor the Signal Strength from all points of test.

In Test no. 1, 2, & 3 Mobile Terminating (MT), any phone can used capable for receiving files or test type from Mobile Originating and located near the testing area.

Test no. 4 & 5 are for Data Testing. DL & UL of data should be test with minimum of 2 samples each Test point in 1 minute duration. DUMETER will be used in measuring average throughput each test. Screenshots are needed for each samples when time reaches 1 minute in DU meter stopwatch during Download and Upload.

TEST NO. UE SET-UP FUNCTIONALITY TEST TEST EQUIPMENT TEST TYPE TEST

METHOD SAMPLES COMPLETION

1 MS1-MO VOICE CALL MO & MT TEMS UE's CS STATIONARY Minimum of 2 samples 100%

2 MS1-MO MMS MO & MT TEMS UE's PS STATIONARY Minimum of 2 samples 100%

3 MS1-MO SMS MO & MT TEMS UE's PS STATIONARY Minimum of 2 samples 100%

5 MS1-DL HSDPA -125MB DONGLE PS STATIONARY Minimum of 2 samples -

6 MS1-UL HSDPA – 50MB DONGLE PS STATIONARY Minimum of 2 samples -

2G TEST 3G TEST


Test2. WALK Test-Handover Test. For 2G & 3G

TEST METHOD. Test will be used for Handover test from Indoor cell coverage to outdoor cell coverage and outdoor cell coverage to Indoor Cell coverage. All Entrance and Exit of building with IBS and Basement Car park/building Car park ( if applicable) should perform Handover Testing.

TEST NO UE SET-UP TECHNOLOGY TEST EQUIPMENT

TEST TYPE

TEST METHOD

CALL DURATION(s)

IDLE MODE(s) B NUMBER

1 MS1 2G-LONG CALL TEMS UE's CS MOBILITY 999999 NR

B. : Any phone number (same

network) located near the Mobile

Originating Phone area of test

TEST NO UE SET-UP TECHNOLOGY TEST EQUIPMENT

TEST TYPE

TEST METHOD

CALL DURATION(s)

IDLE MODE(s) B NUMBER





2G TEST 3G TEST

FOR 2G. 2G-3G idle/PS cell reselection test. Update September 11, 2012

UE SET-UP TECHNOLOGY Purpose(s) TEST

EQUIPMENT TEST TYPE CALL DURATION(s) IDLE MODE(s) B NUMBER SAMPLE

MS1 2G-IDLE MODE Cell Reselection test 2G-3G idle/PS. Each sector shall perform cell reselection test to its neighboring 3G site after swap. If applicable. TEMS UE's PS Cell

reselection NR NR N/A NR

Test3. WALK Test-Cell reselection Test. For 2G & 3G

FOR 3G. 3G-2G idle/PS cell reselection test. Update September 11, 2012

UE SET-UP TECHNOLOGY Purpose(s) TEST

EQUIPMENT TEST TYPE CALL DURATION(s) IDLE MODE(s) B NUMBER SAMPLE

MS1 3G-IDLE MODE Cell Reselection test 3G-2G idle/PS. Each sector shall perform cell reselection test to its neighboring 2G site after swap. If applicable. TEMS UE's PS Cell

reselection NR NR N/A NR

TEST METHOD. PS cell reselection Test shall perform for each cells after swap to its neighboring cells/site. For 2G, test 2G-3G cell reselection and for 3G, test 3G-2G PS cell reselection.


TEST METHOD. Test Signal Strength Spillage of IBS 5 meters distance from the fringe of building and/or along the nearest major street around the building’s perimeter. Signal should be limited to < -85 dBm at a 5 meter distance from the fringe of the building and/or along the nearest major street around the building’s perimeter.

Note: Lock all available BCCH-2G or Scrambling Code-3G of IBS site need to test before performing the Spillage Test.

TEST NO UE SET-UP

TECHNOLOGY

TEST EQUIPMENT TEST TYPE TEST

METHODCALL

DURATION(s)

IDLE MODE(s

)B NUMBER SAMPLE




Originating Phone area of

test

NR

TEST NO UE SET-UP

TECHNOLOGY

TEST EQUIPMENT TEST TYPE TEST

METHODCALL

DURATION(s)

IDLE MODE(s) B NUMBER SAMPLE





NR


Test Method

Outputs Original log files to be surrendered to HT per site basis on a CD/DVD disc Sub con to provide 2G & 3G pre/post benchmarking report to HT for approval & analysis




MS2 2G-LONGCALL TEMS UE's CS MOBILITY 999999 NR B: Any phone placed inside the car (same network) LONG CALL

MS3 2G-IDLE TEMS UE’s IDLE MODE MOBILITY NR NR NR NR

MS4 2G (GPRS/EDGE) TEMS UE's PS-DL MOBILITY DL-3MB 10sec. FTP: NR




MS2 3G/2G DUAL MODE TEMS UE's CS CALL MOBILITY 999999 NR B: Any phone placed inside the car

(same network) LONG CALL

MS3 3G HSDPA DONGLE/DATA CARD PS-DL MOBILITY DL-125M FTP 10sec. FTP: NR

2G

3G

5.3. POST DT (CLUSTER LEVEL) Guideline Guidelines covers both technology To be conducted upon 100% full cluster integration with SWAP configuration Shall cover all sites within swap cluster until 1 layer neighbor at adjacent cluster Test are purely mobility For 3G testing, when 3G handover to 2G, stop the car and terminate the call and data collection. Wait for the test phone perform reselect to camp to 3G again, and

then that the time to start recording again. This scenario is case to case basis, particularly in areas ( in particular in rural areas) with no 3G neighbors or signal is very poor compared to 2G neighbor. Also in areas with no 3G site intended to cover the areas with DT routes.


5.4. Cluster Level Acceptance DT

Guideline Guidelines covers both technology To be conducted upon 100% full cluster integration + expansion (as forecast) Shall cover all sites within swap cluster until 1 layer neighbor at adjacent cluster Shall perform after the Acceptance of Site in a Cluster Test covers Mobility and Stationary Drive test call samples should be >400 calls for each technology ( case to case basis especially for cluster with small number of sites <10 sites). For Stationary, Testing covers PS download and Upload in per cell level both 2G & 3G technology ( (EDGE, R99, HSDPA, HSPA+). VOICE QUALITY MOS will perform after all DT KPI passed.

Test1. CS & PS. Mobility1

MOBILITY TEST 1- LAPTOP 1

UE SET-UP TECHNOLOGY TEST

EQUIPMENT TEST TYPE CALL DURATION(s)

IDLE MODE(s) B NUMBER/ FTP SERVER SAMPLE

MS1 2G-SHORTCALL TEMS UE’s CS CALL 45 15

B: Any phone placed inside the car (same network)

400(minimum)

MS2 2G-LONGCALL TEMS UE's CS 999999 NR B: Any phone placed inside the car (same network)

NR

MS3 2G SCANNER CS NR NR NR NR

MS4 2G (GPRS/EDGE) Dongle PS-DL DL-3MB NR FTP:

MOBILITY TEST 1- LAPTOP 1

UE SET-UP TECHNOLOGY TEST

EQUIPMENT TEST TYPE CALL DURATION(s)

IDLE MODE(s) B NUMBER/ DL/UL Server SAMPLE

MS1 3G TEMS UE’s CS CALL 45 15 B: Any phone placed inside the car (same network) 400(minimum)

MS2 2G/ 3G (DUAL MODE) TEMS UE's CS 999999 NR B: Any phone placed inside

the car (same network) NR

MS3 3G SCANNER CS NR NR NR NR

MS43G

(HSDPA/HSPA) DL

Dongle PS-DL DL – 125MB NR FTP: ?

2G 3G


MOBILITY 1 – LAPTOP 2

UE SET-UP TECHNOLOGY TEST EQUIPMENT TEST TYPE CALL DURATION(s) IDLE

MODE(s)B NUMBER/

DL/UL Server

SAMPLE

MS1 2G TEMS UE’s SMSPING

SMSPING - SMS : A TO A Minimum of 10

samples

MS2 2G (GPRS/EDGE) TEMS UE’s PS-UL UL-1MB NR FTP:

MOBILITY TEST 1 – LAPTOP2

UE SET-UP TECHNOLOGY TEST EQUIPMENT TEST TYPE CALL

DURATION(s) IDLE MODE(s) B NUMBER/ DL/UL Server SAMPLE

MS1 2G TEMS UE’s SMSPING

SMSPING - SMS : A TO A Minimum of 10

samples

MS23G

(HSDPA/HSPA) UL

Dongle PS-UL UL – 50MB NR FTP:

2G 3G

MOBILITY 1 – TEST3

UE SET-UP TECHNOLOGY TEST EQUIPMENT TEST TYPE SAMPLE

MS1 2G PROBE VOICE QUALITY MOS -

Test 2. MOS test. Mobility2

MOBILITY 1 – TEST3

UE SET-UP TECHNOLOGY TEST EQUIPMENT TEST TYPE SAMPLE

MS1 3G PROBE VOICE QUALITY MOS -

2G 3G


STATIONARY TEST

TEST NO. UE SET-UP TECHNOLOGY TEST EQUIPMENT

TEST TYPE

TEST METHOD

DL/UL SERVER SAMPLE(s)

1 MS1-DL 2G TEMS UE's PS STATIONARY FTP:

2(Must

complete DL

session)

2 MS1-UL 2G TEMS UE's PS STATIONARY FTP:

2(Must

complete UL

session)

STATIOANRY TEST

TEST NO. UE SET-UP TEST DESCRIPTION TECHNOLOGY TEST

EQUIPMENTTEST TYPE

TEST METHOD

DL/UL SERVER SAMPLE(s)

1 MS1-DL

CONTINUE DOWNLOADING BIG FTP FILE 3G : 2.0MBHSDPA : 22.0MBHSPA+ : 38.0MB

3G ( R99/HSDPA/HSPA+)

TEMS UE's/DONGLE PS STATIONARY FTP:

2(Must

complete DL session)

2 MS1-UL

CONTINUE DOWNLOADING BIG FTP FILE 3G : 0.50MBHSDPA : 7.20MBHSPA+ : 11.0MB

3G ( R99/HSDPA/HSPA+)

TEMS UE's/DONGLE PS STATIONARY FTP:

2(Must

complete UL session)

2G 3G

Outputs Original log files to be surrendered to HT per site basis on a CD/DVD disc Sub con to provide 2G & 3G cluster acceptance report to HT for approval & analysis

Minimum of 2 samples needed per cell. Meaning; 2 samples for download and 2 samples for upload each cell.

Each Sample must finish the download session with required/agreed file size. Throughput measurement should be from 30% to 90% of file size. The value of throughput will be get from “Application Throughput” and exported from TEMS or Actix post

Test 3. DL & UL test. Stationary


DT SUMMARY TOOLS


Drivetest Summary & Report Processing tools

2G Rx Lev dbm Below -95 >= -95 to <-85 >= -85 to <-80 >= -80 to <-75 >= -75 to <-70 >= -70 to <-64 >= -64

2G RxQual

<=4

> 4 to < 5

>=5 to < 8

2G DL THROUGHPUT Kbps

Below 50

>= 50 to < 70

>= 70 to < 80

>= 80 to < 90

>= 90

2G UL THROUGHPUT Kbps

Below 10

>= 10 to < 24

>= 24 to < 40

>= 40 to < 45

>= 45

1. 2G LEGENDS

2. 3G LEGENDS

3G RSCP dbm

Below -95

>= -95 to <-85

>= -85 to <-80

>= -80 to <-75

>= -75

3G Ec/No

>= -10

< -10 to -14

< -14

3G DL THROUGHPUT Kbps

Below 1000

>= 1000 to < 2000

>= 2000 to < 3300

>= 3300 to < 4000

>= 4000

3G UL THROUGHPUT Kbps

Below 500

>= 500 to < 1000

>= 1000 to < 1200

>= 1200 to < 2000

>= 2000

Signal strength Legend Signal quality Legend Download throughput Legend Upload throughput Legend

Signal strength Legend Signal quality Legend Download throughput Legend Upload throughput Legend


3. DL & UL FILESIZE. MOBILITY & STATIONARY

TEST TYPE FILESIZE TO DL/UL

2G DL 0.70 MB2G UL 0.35 MB3G DL 2.0 MB3G UL 0.50 MBHSDPA DL 22.0 MBHSDPA UL 7.20 MBHSPA+ DL 38.0 MBHSPA+ UL 11.0 MB

TEST TYPE FILESIZE TO DL/UL

2G DL 3.0 MB

2G UL 1.0 MB

3G DL 125.0 MB

3G UL 50.0 MB

3. POST PROCESSINGTOOLS. Actix Setting

Set Location under Binning mode

Set Projection to World Geodetic System 1984 (GPS)

Set X: 005 & Y : .005

Set to Arcseconds

Thank youwww.huawei.com

Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved.The information in this document may contain predictive statements including, without limitation, statements regarding the future financial and operating results, future product portfolio, new technology, etc. There are a number of factors that could cause actual results and developments to differ materially from those expressed or implied in the predictive statements. Therefore, such information is provided for reference purpose only and constitutes neither an offer nor an acceptance. Huawei may change the information at any time without notice.

globe nemesis drivetest methodology_v3

Documents

nearest major

measuring

outputsoriginal

indoor cell

outdoor cell

ssv report

sms mo amp

mms mo amp