gobo light manual - event decor direct86-90 chase 1 91-95 chase 2 96-100 chase 3 101-255 reserved -...
TRANSCRIPT
GOBO LED Light
DS-1404AUSER MANUAL
�21. IntroductionThank you for purchasing our GOBO LED light. Please read these instructions carefully before operating to avoid any possible damage and accidents caused by misuse.
The GOBO LED light has a hydrodynamic aluminum shell. One 10W white LED is used to create a bright light output. It draws low power and is low weight.
Packing List
- LED GOBO Light- User manual- Power cord
2. Safety Information
- Please consult skilled service technicians for any repairs required- Always disconnect from the power source before setting up, moving and
servicing- Avoid direct eye contact to the light when in operation- Make sure the power supply voltage is compatible with this light- Before installation, please check the light’s fasteners and mechanical
structure is in good condition and not damaged- The light is designed for indoor use, below 40 degrees celsius- The fixture may be mounted in any position provided there is adequate
room for ventilation. Make sure there are no flammable and explosive items within 0.5 meters.
- Please ensure the ground is always connected
�3
3. Dimensions and SpecificationsVoltage: AC100V/264 VACFrequency: 47-63 HzPower Consumption: 25 W
Lamp: 10W white LEDBeam Angle: 13 degreesNet Weight: 2 KgIP Rating: IP20
Dimensions:
�
www.EddyLight.com 1-800-914-3538
�44. GOBO Installation
Unscrew the 2 knobs on the top of the projector and remove the piece from inside
Place the GOBO in the center hole. Squeeze the ring and place it on top of the GOBO to ensure the GOBO stays in place.
After the GOBO is placed in the correct orientation, place the GOBO holder back into the projector and screw it on.
�5
5. Operation
The easiest way to operate your projector is through the remote control. You can also use the buttons on the projector to go through the options.
All of the options are set using a scale of 0-255. To set it to the number you desire, move UP or DOWN to that number and press ENTER. The light will turn off, then press ENTER again.
R - Red light intensity (0 off, 1 dimmest, 255 brightest)
G - Green light intensity (0 off, 1 dimmest, 255 brightest)
B - Blue light intensity (0 off, 1 dimmest, 255 brightest)
W - White light intensity (0 off, 1 dimmest, 255 brightest)
SHUT - Strobe effect. 0 = no strobe effect. 1-255 different strobe pattern and speed
GOBO - Rotation feature. 000 = off1-100 = different positions101-170 = different speeds of counterclockwise rotation185 - 250 = different speeds of clockwise rotation
NOTE: R, G, B options are only for color projector. You can mix different values of red, green and blue to create any color.
www.EddyLight.com 1-800-914-3538
x
x
x
x
x
x
x
x
0 0 0 0 M
ENU
UP
DO
WN
ENTER
x
MADE IN CHINA
IR
RoHS
To focus the projector, rotate the lens. Every time you adjust the distance of the projector to the projection surface, you will need to adjust the focus
Focus
�66. DMX Control Function
3CH 5CH VALUE FUNCTION
CH1 CH1 0-255 Intensity
CH2
0-5 No strobe
6-20 Random burst strobe(slow to fast)
21-60 Normal strobe(slow to fast)
61-100 Electronic Sinewave(slow to fast)
101-140 Random Strobe(slow to fast)
141-180 Opening pulse(slow to fast)
181-220 Closing pulse(slow to fast)
221-255 Electronic Squarewave(slow to fast)
CH3 CH3
0-100 0-360°
101-170 CW(slow to fast)
171-180 Stop
181-250 CCW(slow to fast)
251-255 Stop
- CH4
0-70 No effect
71-75 AUTO 1(W + GOBO CW)
76-80 AUTO 2(W↑,W↓ + GOBO CW)81-85 AUTO 3(W + GOBO CCW)
86-90 CHASE 1
91-95 CHASE 2
96-100 CHASE 3
101-255 Reserved
- CH5
0-10 Use the dimmer mode which menu has set up
11-20 Dimmer off
21-30 Dimmer 1
31-40 Dimmer 2
41-50 Dimmer 3
51-60 Dimmer 4
61-254 Use the dimmer mode which menu has set up
�7
7. Display Operation Instruction
Instructions:Master mode sends a DMX signal to all other LED light units connected via DMX.
Slave mode receives the incoming DMX signal from the Master, using the values set by the Master unit.This allows for a large group of lights to be connected and controlled by only one light.
For Master mode, press ENTER on the unit to display “*” on the LED display.
When there is no “*” being displayed on the LED display, the light is set to Slave by default.
MENU access the menu or return to a previous menu option
ENTER select the current menu option
UP menu selection or parameter increments
DOWN menu selection or parameters decrease
www.EddyLight.com 1-800-914-3538
�8Tab Level 1 Level 2 Level 3 Level 4
ADDR(Address) 001-512
STAT(Static control) W 0-255*
SHUT 0-255*
GOBO 0-255*
SET(Set) CHMD(Channel mode) 5CH
3CH
DIM(Dimming mode) OFF
DIM1
DIM2
DIM3
DIM4
DISY(Display set)
ON(Permanent on)
2MIN (2 minutes off)
CALP(Calibrate position) 0-255
AUTO(Auto) AT01 RUN..*
AT02 RUN..*
AT03 RUN..*
CHS1 RUN..*
CHS2 RUN..*
CHS3 RUN..*
PROG(Program)CHS1(Chase 1)
SC01(Scene 1) W 0-255
. . SHUT 0-255 . . GOBO 0-255 . . TIME 0-255(S) . . WAIT 0-25.5(S) . . USE YES/NO
. SC20(Scene 20)
CHS3(Chase 3)
INFO(Information)
SOFT(Software version) Vx.x
POW(Power reduction)
100%/80%/50%
LOAD(Load) ST L(Setting load) YES/NO
PR L(Program load)
YES/NO
SEND(Send) YES/NO
�9
6.1 DMX Address Setting1. Select the ADDR Menu by navigating to it and pressing ENTER. 2. Press the UP/DOWN buttons to navigate between channels 1 - 512.
3. Press ENTER to select your desired channel.
6.2 Static Setting 1. Select the STAT menu by navigating to it and pressing ENTER2. Press the UP/DOWN buttons to select WHITE, SHUT, or GOBO.
3. Press the UP/DOWN buttons to set up the【0-255】numerical value.
4. Press the ENTER button to escape and save.
6.3 Channel Mode Setting1. Select the SET menu by navigating to it and pressing ENTER2. Select the CHMD menu by pressing ENTER3. Press the UP/DOWN buttons to select 3CH or 5CH
4. Press the ENTER button to escape and save.
6.4 Dimming Mode Setting1. Select the SET menu by navigating to it and pressing ENTER2. Select the DIM menu by pressing ENTER3. Press the UP/DOWN buttons to select OFF, DIM1, DIM2, DIM, 3 or
DIM4 4. Press the ENTER button to escape and save.
When off is selected there will be no delay dimming effectDIM1 is the slowest. DIM4 is the fastest.
www.EddyLight.com 1-800-914-3538
�10
6.5 Display Setting1. Select the SET menu by navigating to it and pressing ENTER2. Select the DISY menu by pressing ENTER3. Press the UP/DOWN buttons to select ON, 2MIN.
4. Press the ENTER button to escape and save.
6.6 Calibrating the GOBO to Original Position1. Select the SET menu by navigating to it and pressing ENTER2. Select the CALP menu by pressing ENTER3. Press the UP/DOWN buttons to set up the 0-255 numerical value.
4. Press the ENTER button to escape and save.
6.7 Auto Run, Self-Program1. Select the AUTO menu by navigating to it and pressing ENTER2. Press the UP/DOWN buttons to select AT01, AT02,AT03, CHS1,
CHS2, CHS33. Press the ENTER button to escape and save.
�11
6.8 Edit Self-Program1. Select the PROG menu by navigating to it and pressing ENTER2. Press the UP/DOWN buttons to select CHS1, CHS2, or CHS3
3. Press the ENTER button for confirmation and enter to the next menu.
4. Press the UP/DOWN buttons to select from SC1-SC20
5. Press the ENTER button for confirmation and enter to the next menu.
6. Press the UP/DOWN buttons to select W, GOBO, TIME, WAIT, USE,
or SHUT 7. Press the UP/DOWN buttons to set the parameter which are needed.
8. Press the ENTER button to escape and save.
When USE is set to NO,or the parameter of TIME is 0, it will not run
this scene.When WAIT is set to be FADE time, the running process is as the following chart showing.
6.9 Checking Lighting Information1. Select the INFO menu by navigating to it and pressing ENTER2. SOFT is for software version information.3. POW is for the current information of power reduction.
100% is the normal output. Projector will reduce to 80% or 50% output to protect from over-heating.
www.EddyLight.com 1-800-914-3538
�126.10 Lighting Setting Parameter Reset1. Select the LOAD menu by navigating to it and pressing ENTER 2. Select the ST L menu by navigating to it and pressing ENTER 3. Press the UP/DOWN buttons to select YES or NO.
4. Press the ENTER button to escape and save.
ADDR, CALP and “PROG” are not reset, the others reset to the underlined value of the word.
6.11 PROG: SELF-PROGRAMMING PARAMETER RESET1. Select the LOAD menu by navigating to it and pressing ENTER 2. Select the PR L menu by navigating to it and pressing ENTER3. Press the UP/DOWN buttons to select YES or NO.
4. Press the ENTER button to escape and save.
6.11 Lighting ParameterDownload Via DMX Cable1. Select the SEND menu by navigating to it and pressing ENTER2. Press the UP/DOWN buttons to select YES or NO.
3. Press the ENTER button to escape and save.
Please disconnect the connection of projector and DMX console before sending the parameter.
ADDR and CALP information can’t be sent or downloaded
There will be an automatic reset of the other projectors after receiving parameter correctly
�13
7. Remote Control
MENU, UP, DOWN, ENTER are the same as the corresponding buttons on the projectorR - Red, G - Green, B - Blue, W - White, SHUT - Strobe, GOBO - Rotation
AT01, AT02, AT03, CHS01, CHS02, CHS03 are shortcuts of AUTO
www.EddyLight.com 1-800-914-3538
�148. Operating Control Instruction
Master/SlaveWhen the device is in MASTER mode it will automatically send out the signal to its slave.
To avoid the host and DMX512 signals from interfering with each other, DMX512 signals should be shut off.
If signal lines are longer than 60 meters or 20 lamps, you should use a single amplifier.
9. XLR Connection
In order to avoid failures and interference, connect a resistance 120Ω (1/4W) at the end of the DMC connection.
�15
If the output cable of the DMX512 controller is 5PIN, use 5PIN to 3PIN cable
www.EddyLight.com 1-800-914-3538
�16