goodtool brake service tools and supplies quick chuck

GoodtoolBrake Service Tools and Supplies

Quick ChuckQuick Chuck

Goodtool Brake Supplies 1-800-880-7121 Phone: 507 454-1454 www.goodtool-online.com 2

Quick Chuck Self centering system• Will mount on any Brake Lathe with a 1” arbor• Eliminates mounting problems with the unique self

centering system• No use of cones or bell clamps• Fits hubless rotors and drums, and composite rotors and

drums• Fits most foreign and domestic rotors, drums and

flywheels including light trucks with a centering hole ranging from 2-1/8” to 5 -3/4” in diameter

• 25% less set up time, accurate microfinish and reduces chatter.

• Fits on small automotive to large truck rotors

• Will mount on any Brake Lathe with a 1” arbor• Eliminates mounting problems with the unique self

centering system• No use of cones or bell clamps• Fits hubless rotors and drums, and composite rotors and

drums• Fits most foreign and domestic rotors, drums and

flywheels including light trucks with a centering hole ranging from 2-1/8” to 5 -3/4” in diameter

• 25% less set up time, accurate microfinish and reduces chatter.

• Fits on small automotive to large truck rotors


Go From all this…

To just this…


Step One

• Thoroughly clean the surface of the rotor or drum that will be mounted on the Quick Chuck. ( Step 1A & 1B)

• Thoroughly clean the surface of the rotor or drum that will be mounted on the Quick Chuck. ( Step 1A & 1B)

Step 1AStep 1B


Step 2 • Place the hubless rotor

or hubless drum on a clean, flat surface. Attach your hubless rotor or drum to the Quick Chuck by positioning the Quick Chuck with the jaws in the center hole.

• Place the hubless rotor or hubless drum on a clean, flat surface. Attach your hubless rotor or drum to the Quick Chuck by positioning the Quick Chuck with the jaws in the center hole.


Step 2B• Tighten the jaws by inserting

the key into one of the key slots in the side of the chuck, turning counterclockwise. The Quick Chuck will automatically self-center the rotor or drum. Make sure that the chuck jaws are tight. DO NOT leave the key in the key slot when starting the brake lathe.

• Tighten the jaws by inserting the key into one of the key slots in the side of the chuck, turning counterclockwise. The Quick Chuck will automatically self-center the rotor or drum. Make sure that the chuck jaws are tight. DO NOT leave the key in the key slot when starting the brake lathe.


Step 3A • Install the backing plate onto the brake lathe arbor

with offset backing outward. • Install the backing plate onto the brake lathe arbor

with offset backing outward.


Step 3B

• Mount the Quick Chuck with drum or rotor installed onto the 1" arbor

• Mount the Quick Chuck with drum or rotor installed onto the 1" arbor


Step 3C• Using the spacers supplied with the brake lathe, add as

many as needed to reach the arbor threads• Using the spacers supplied with the brake lathe, add as

many as needed to reach the arbor threads


Step 3D

• Using the adjusting nut supplied with the machine, tighten the nut against the spacers. After tightening the Quick Chuck, turn on the brake lathe to check for run-out of the rotor or drum. Run-out spec. is .001” You are now ready to resurface the rotor or drum.

• Using the adjusting nut supplied with the machine, tighten the nut against the spacers. After tightening the Quick Chuck, turn on the brake lathe to check for run-out of the rotor or drum. Run-out spec. is .001” You are now ready to resurface the rotor or drum.


• This job can be done quickly and will eliminate customer’s complaints of rotors or drums saving you time and making you money.

• This job can be done quickly and will eliminate customer’s complaints of rotors or drums saving you time and making you money.


• SPECIAL NOTE: The Quick Chuck will allow the turning of hubless rotors and drums to be performed on any brake lathe with an 1” arbor.

• SPECIAL NOTE: The Quick Chuck will allow the turning of hubless rotors and drums to be performed on any brake lathe with an 1” arbor.

Ammco Twin Cutters

Ammco HD

Accu-Turn

BeanBear

FMC

Hoffman

RJ West

Horvath

Hunter Kwik-Way

Performance

Pro-Cut RTI Snap-On

StarVan Norman

Rels

VBG


• Important – Please note ALWAYS use the largest possible backing plate. This will help eliminate the rotor or drum vibration while being turned. On some brake lathes, a small spacer may be needed before the installation of the backing plate.

• Important – Please note ALWAYS use the largest possible backing plate. This will help eliminate the rotor or drum vibration while being turned. On some brake lathes, a small spacer may be needed before the installation of the backing plate.


• *Do not use air tools on the unit at any time.• *Do not use air tools on the unit at any time.


• NOTE: THE CLEANING OF THE CHUCK. When the jaws have been removed it allows for cleaning of the Chuck (the jaws are numbered on the side as 1, 2, 3) it is VERY IMPORTANT that they be reinstalled in the same manner that they were removed. Reinstall in the order of 1-2-3 (counterclockwise). A slight amount of pressure may be required on each of the jaws to allow them to be reinstalled evenly and correctly. (Figure 1 & 2 below)

• NOTE: THE CLEANING OF THE CHUCK. When the jaws have been removed it allows for cleaning of the Chuck (the jaws are numbered on the side as 1, 2, 3) it is VERY IMPORTANT that they be reinstalled in the same manner that they were removed. Reinstall in the order of 1-2-3 (counterclockwise). A slight amount of pressure may be required on each of the jaws to allow them to be reinstalled evenly and correctly. (Figure 1 & 2 below)

1 294


Automotive Quick Chuck PartsGT-70040 -- Automotive Chuck Adaptor KitKit includes • Quick Chuck Adaptor• Automotive Jaws Range of 2-1/8” to 3-3/4”• Standard Backing Plate 5.2” OD• Chuck Key

Replacement parts GT-70042 -- Quick Chuck Adaptor w/ JawsGT-70045 -- Replacement Automotive Jaws 2-1/8” to 3-3/4”GT-70043 -- Standard Backing Plate 5.2” ODGT-70044 -- Chuck Key

GT-70040 -- Automotive Chuck Adaptor KitKit includes • Quick Chuck Adaptor• Automotive Jaws Range of 2-1/8” to 3-3/4”• Standard Backing Plate 5.2” OD• Chuck Key

Replacement parts GT-70042 -- Quick Chuck Adaptor w/ JawsGT-70045 -- Replacement Automotive Jaws 2-1/8” to 3-3/4”GT-70043 -- Standard Backing Plate 5.2” ODGT-70044 -- Chuck Key

Fits 1” Arbors


Truck Quick Chuck PartsGT-70040 -- Truck Chuck Adaptor Kit (can be used for automotive applications)Kit includes • Quick Chuck Adaptor• Automotive Jaws Range of 2-1/8” to 3- 3/4”• Truck Jaws Range of 3-3/4” to 5-3/4”• Truck Backing Plate 7-1/4” OD• Standard Backing Plate 5.2” OD• Chuck Key

Replacement parts GT-70042 -- Quick Chuck Adaptor w/ JawsGT-70045 -- Replacement Automotive Jaws range of 2-1/8”to 3-3/4”GT-70041 -- Large Jaw Set range of 3-3/4 “ to 5-3/4”GT-70046 -- Truck Backing Plate 7-1/4 “ ODGT-70043 -- Standard Backing Plate 5.2” ODGT-70044 -- Chuck Key

GT-70040 -- Truck Chuck Adaptor Kit (can be used for automotive applications)Kit includes • Quick Chuck Adaptor• Automotive Jaws Range of 2-1/8” to 3- 3/4”• Truck Jaws Range of 3-3/4” to 5-3/4”• Truck Backing Plate 7-1/4” OD• Standard Backing Plate 5.2” OD• Chuck Key

Replacement parts GT-70042 -- Quick Chuck Adaptor w/ JawsGT-70045 -- Replacement Automotive Jaws range of 2-1/8”to 3-3/4”GT-70041 -- Large Jaw Set range of 3-3/4 “ to 5-3/4”GT-70046 -- Truck Backing Plate 7-1/4 “ ODGT-70043 -- Standard Backing Plate 5.2” ODGT-70044 -- Chuck Key

Fits 1”Arbors


Other Optional Parts GT-70047 -- Small Automotive Backing Plate Plate 4-1/4” ODGT-70054 -- Toyota Backing Plate 6-1/4” OD(Each sold separately not included in any kits)

GT-70047 -- Small Automotive Backing Plate Plate 4-1/4” ODGT-70054 -- Toyota Backing Plate 6-1/4” OD(Each sold separately not included in any kits)


GoodtoolBrake Service Tools and Supplies

•Quick Chuck• Any questions on the Quick Chuck : please

contact us• Toll Free: 1-800-880-7121

• Phone: 507-454-1454• Fax: 507-454-1471

• www.goodtool-online.com.com

•Quick Chuck• Any questions on the Quick Chuck : please

contact us• Toll Free: 1-800-880-7121

• Phone: 507-454-1454• Fax: 507-454-1471

• www.goodtool-online.com.com

goodtool brake service tools and supplies quick chuck

Documents

goodtool brake supplies

quick chuck slide

hubless rotors

brake lathe arbor

chuck jaws

b slide

composite rotors

domestic rotors