gpib connector size, and ieee488 pinout and signal names
TRANSCRIPT
11/29/11 GPIB Connector Size, and IEEE488 pinout and Signal Names
1/3www.interfacebus.com/Design_GPIB_Mechanical.html
IEEE-488 Connector Size
Search
This page describes the GPIB connector including a drawing with dimensions. Pins 1 to 12 are located on the bottom row, while pins 13 to 24 are located on the top row as shown [narrow side ofconnector]. The top portion of the drawing depicts a female connector, and the bottom drawing depicts a male GPIB connector. The Female connector provides pin 1 on the bottom left pin, pin 12 on the bottom right, pin 13 is above pin 1, while pin 24.The male connector has the same pinout but it's mirrored. So the male connector has pin 1 on the lower right.A pin out table with signal names for the GPIB connector is provided after the connector drawing.
GPIB Connector [Receptacle to Plug Assembly]
The Mechanical [Physical] Dimensions for the GPIB connector is shown in the graphic above.
In addition to the physical dimensions, the drawing also shows the type of bolts.
Mechanical Engineer Degree Get an Engineering Degree in 24 Hrs based on your work/Life Experience. www.WEVACUniversity.com/UAE
Electronic Connector Serv ECS manufacturers solder and press fit PC and I/O connectors www.ecsconn.com
Plastic Tubing Connectors VP plastic tube fittings and tubing connectors. Shipped today! www.ValuePlastics.com
Data Bus Products Corp. Mfr of 1553 couplers, terminators cable assy, connectors, PL75-47 www.databusproducts.com
Mechanical Engineer Degree Get an Engineering Degree in 24 Hrs based on your work/Life Experience. OULifeExperienceDegrees.com
MIL-C-26500 Connectors Cinch assembled in 48 hours The MIL-C-26500/BACC (Omega) Series www.peigenesis.com/en/cinch
11/29/11 GPIB Connector Size, and IEEE488 pinout and Signal Names
2/3www.interfacebus.com/Design_GPIB_Mechanical.html
In addition to the physical dimensions, the drawing also shows the type of bolts.
The GPIB bus is also called, HPIB bus , or IEEE-488 bus .
IEEE-488 Connector types: (The connector pin-outs differ):
... IEEE488/ANSI MC1.1; 24 pins, accepts a ribbon cable.
... IEC 625-1, MIL-C-24308; 25 pinsConnectors are tested to MIL-STD-202E (Environmental).Maximum cable length is 20 meters, or 2 meters per device - which ever is less. Devices may be connected in either aStar or Linear fashion.Metric threads are Black, English threads are Silver; the two will not mate togetherBack to the main GPIB / HPIB; IEEE-488 page for pin descriptions, timing and a bus description.
ANSI Connector / IEEE488 PinOut
24-Pin GPIB Bus PinOut and Signal Assingments
Pin # Signal Names Signal Description Pin # Signal Names Signal Description
1 DIO1 Data Input/Output Bit 1 13 DIO5 Data Input/Output Bit 5
2 DIO2 Data Input/Output Bit 2 14 DIO6 Data Input/Output Bit 6
3 DIO3 Data Input/Output Bit 3 15 DIO7 Data Input/Output Bit 7
4 DIO4 Data Input/Output Bit 4 16 DIO8 Data Input/Output Bit 8
5 EIO End-Or-Identify 17 REN Remote Enable
6 DAV Data Valid 18 Shield Ground (DAV)
7 NRFD Not Ready For Data 19 Shield Ground (NRFD)
8 NDAC Not Data Accepted 20 Shield Ground (NDAC)
9 IFC Interface Clear 21 Shield Ground (IFC)
10 SRQ Service Request 22 Shield Ground (SRQ)
11 ATN Attention 23 Shield Ground (ATN)
12 Shield Chassis Ground 24 Single GND Single Ground
GPIB Connector Receptacle
Free e-Learning Modules Intuitive Agilent VEE Programming Basics Modules. Get them Now! www.agilent.com/find/learnvee
N Female Connector Pasternack is in Stock 99.4% N Female Connectors Ship Same Day www.pasternack.com
Smart Power Management Working together for a sustainable future - Siemens Energy Efficiency! siemens.ae/energy-efficiency
11/29/11 GPIB Connector Size, and IEEE488 pinout and Signal Names
3/3www.interfacebus.com/Design_GPIB_Mechanical.html
GPIB Connector Receptacle
Military Commercial Item Descriptions;GPIB connectors, by CID document number
Home
Distributors Components Equipment Software Standards Buses Design Reference
Modified 9/4/11Copyright © 1998 - 2011 All rights reserved Leroy Davis