gpu alcatel
DESCRIPTION
GPU AlcatelTRANSCRIPT
-
Alcatel BSS
B9 BSS Configuration Rules
BSS Document
Reference Guide
Release B9
3BK 17422 5000 PGZZA Ed.06b
-
Status RELEASED
Short title Configuration Rules
All rights reserved. Passing on and copying of this document, useand communication of its contents not permitted without writtenauthorization from Alcatel/Evolium.
BLANK PAGE BREAK
2 / 162 3BK 17422 5000 PGZZA Ed.06b
-
Contents
ContentsPreface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.1 BSS Equipment Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.2 Supported Hardware Platforms, Restrictions and Retrofits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.3 Platform Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151.4 Release Migration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151.5 BSS Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151.6 New B9 Features and Impacted Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2 BSS Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.1 Transmission Architecture with CS Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202.2 Transmission Architecture with CS and PS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.3 GPRS in the BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.3.1 GPRS Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222.3.2 GPRS General Dimensioning and Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.4 LCS in the BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302.4.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302.4.2 Logical Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302.4.3 Physical Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312.4.4 Functional Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322.4.5 GPS LCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332.4.6 BSS and Cell Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342.4.7 Traffic Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352.4.8 Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.5 HSDS in the BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352.5.1 Definitions and Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352.5.2 Transmission Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392.5.3 Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.6 PLMN Interworking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433 BTS Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.1 BTS Generation Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463.2 Evolium BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.2.1 Evolium BTS Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463.2.2 Evolium BTS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.3 G2 BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503.4 G1 BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503.5 BTS Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503.6 Physical Channel Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.6.1 GSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513.6.2 GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.7 Frequency Band Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.7.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.7.2 Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523.7.3 Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
3.8 Speech Call Traffic Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533.9 Adaptive Multi-rate Speech Codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.9.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543.9.2 Rules and Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
3.10 Data Call Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553.11 OML and RSL Submultiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553.12 Cell Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3.12.1 Cell Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553.12.2 Frequency Hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573.12.3 Shared Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
3BK 17422 5000 PGZZA Ed.06b 3 / 162
-
Contents
3.13 SDCCH Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593.13.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593.13.2 Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
4 BSC Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614.1 A9120 BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
4.1.1 A9120 BSC Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 624.1.2 ABIS TSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674.1.3 ATER TSU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 714.1.4 TSC Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
4.2 A9130 BSC Evolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 734.2.1 A9130 BSC Evolution Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 734.2.2 Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 774.2.3 A9130 Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
4.3 Delta A9130 BSC Evolution versus A9120 BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 815 TC Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.1 G2 TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 855.1.1 Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 855.1.2 Rules and Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
5.2 A9125 Compact TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865.2.1 Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865.2.2 Rules and Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
6 MFS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896.1 A9135 MFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
6.1.1 MFS Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906.1.2 MFS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 926.1.3 MFS Clock Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
6.2 A9130 MFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 946.2.1 MFS Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 946.2.2 MFS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956.2.3 MFS Clock Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.3 Delta A9135MFS versus A9130MFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977 ABIS Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
7.1 Abis Network Topology and Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007.2 Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017.3 Abis Channel Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
7.3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017.3.2 TS0 Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
7.4 Signaling Link on Abis Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027.4.1 RSL and OML . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027.4.2 Qmux Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027.4.3 OML Autodetection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
7.5 Signaling Link Multiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037.5.1 Signaling Link Multiplexing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037.5.2 Signaling Link Multiplexing Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037.5.3 Multiplexed Channel Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
7.6 Mapping Techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1047.6.1 Free Mapping Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1047.6.2 Abis-TS Defragmentation Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1057.6.3 RSL Reshuffling Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1057.6.4 Cross-Connect Use on Abis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067.6.5 SBL Numbering Scheme in A9120 BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1077.6.6 SBLs Mapping on HW Modules in A9130 BSC Evolution versus A9120 BSC 1097.6.7 TCU Allocation Evolution in A9130 BSC Evolution . . . . . . . . . . . . . . . . . . . . . . . . 109
7.7 Abis Link Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1107.8 Abis Satellite Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
4 / 162 3BK 17422 5000 PGZZA Ed.06b
-
Contents
7.9 Two Abis Links per BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1138 Ater Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
8.1 Ater Network Topology and Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188.2 Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188.3 Numbering Scheme on A9120 BSC-Ater/Atermux/TC Ater/A Interface . . . . . . . . . . . . . . . . . 118
8.3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188.3.2 Numbering Scheme on the A9120 BSC Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1198.3.3 Numbering Scheme at G2 TC Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
8.4 Numbering Scheme on A9130 BSC Evolution-Ater/Atermux/TC Ater/A Interface . . . . . . . . 1208.4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1208.4.2 SBLs Mapping on HW Modules in A9130 BSC Evolution versus A9120 BSC 120
8.5 Signaling on Ater/Atermux Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1218.5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1218.5.2 Signaling Link Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1228.5.3 SS7 Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
8.6 GPRS and GSM Traffic on Atermux versus A9120 BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1238.6.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1238.6.2 Hole Management in a G2 TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1248.6.3 Sharing Atermux PCM Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1248.6.4 Ratio of Mixing CS and PS Traffic in Atermux . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
8.7 Ater Satellite Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1279 GB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
9.1 Gb Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1309.2 Gb Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
10 CBC Connection, SMSCB Phase 2+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13310.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13410.2 GSM Cell Broadcast Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13410.3 Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
10.3.1 Solutions in A9120 BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13410.3.2 Solutions in A9130 BSC Evolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
Appendix A : BSS Hardware Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137Appendix B : Cell Radio Channel Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
B.1 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139B.1.1 Cell Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139B.1.2 TRX Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139B.1.3 Hopping Types in a Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141B.1.4 Radio Carrier Hopping Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142B.1.5 Use of the Hopping Types per Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
B.2 Mapping Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144B.2.1 ARFN/CU Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144B.2.2 TCU/RSL & TRX/RSL Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
B.3 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146B.3.1 ARFCN Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146B.3.2 TRX Channel Configuration Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
3BK 17422 5000 PGZZA Ed.06b 5 / 162
-
Figures
FiguresFigure 1: BSS with GPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Figure 2: Transmission Architecture with CS Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Figure 3: Transmission Architecture with CS and PS (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Figure 4: Transmission Architecture with CS and PS (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Figure 5: MFS in the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Figure 6: GPRS NE, Interfaces and Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Figure 7: Example 1 of a Link Configuration: 3/4 GSM& 1/4 GPRS Atermux 4:1 mapping . . . . . . . . . . . . . . 28Figure 8: Example 2 of a Link Configuration: 3/4 GSM& 1/4 GPRS Atermux 4:1 mapping . . . . . . . . . . . . . . 30Figure 9: Generic LCS Logical Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Figure 10: SAGI Physical Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Figure 11: Impact on Hub Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Figure 12: Choice of Modulation Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Figure 13: BTS in the BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Figure 14: BSC in the BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Figure 15: A9120 BSC Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Figure 16: Ater TSU Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72Figure 17: A9130 BSC Evolution HW Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74Figure 18: 600 TRX LIU Shelf connections assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78Figure 19: TC in the BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Figure 20: MFS Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90Figure 21: BSC Connection for Multi-GPU per BSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92Figure 22: A9130 MFS Hardware Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Figure 23: Chain Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100Figure 24: Ring or Loop Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101Figure 25: Example of Cross-Connect Use on Abis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106Figure 26: Gb Link Directly to SGSN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Figure 27: Gb Link through the TC and MSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130Figure 28: Gb Link through the MSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131Figure 29: Gb Logical Context . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132Figure 30: CBC-BSC Interconnection via PSDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135Figure 31: CBC-BSCs Interconnection via the MSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136Figure 32: Maximum Number of Frequencies that can be Encoded in a CBCH Mobile Allocation and a Cell
Allocation (GPRS and of SoLSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151Figure 33: Maximum number of extended measurement frequencies that can be included in the Extended
Measurement Frequency List according to the frequency span. . . . . . . . . . . . . . . . . . . . . . . . . . . 153
6 / 162 3BK 17422 5000 PGZZA Ed.06b
-
Tables
TablesTable 1: BSS Equipment Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Table 2: Supported Hardware Platforms, Restrictions and Retrofits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Table 3: New Features B9 and Impacted Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Table 4: GPRS General Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Table 5: GPRS Coding Schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Table 6: EGPRS Modulation and Coding Schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Table 7: GMSK and 8-PSK Transmission Power Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Table 8: BTS Generation Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Table 9: Evolium BTS Minimum and Maximum Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Table 10: Typical GSM 900 and GSM 1800/1900 Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Table 11: Typical Multiband Configuration G3 BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49Table 12: G2 BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Table 13: BTS Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Table 14: Frequency band configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Table 15: Hardware Transmission Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Table 16: Speech Call Traffic Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Table 17: AMR Codec List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Table 18: Data Call Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Table 19: OML and RSL Submultiplexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Table 20: Cell Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Table 21: Maximum Supported Capacities and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Table 22: A9120 BSC Globally Applicable Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Table 23: BSS Evolution Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Table 24: B9 A9120 BSC Capacity per Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Table 25: TSL / TCU Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Table 26: Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Table 27: DTC Configuration and SBL Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73Table 28: G2 TC/A9125 Compact TC capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Table 29: G2 TC configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Table 30: G2 TC Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86Table 31: MFS Capacity for DS10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Table 32: Maximum MFS Configurations on MX Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96Table 33: Multiplexed Channel Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104Table 34: TS Mapping Table for Corresponding Abis Chain or Ring Configurations . . . . . . . . . . . . . . . . . . . . 107Table 35: SBL Numbering at A9120 BSC Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Table 36: Abis Port - BIUA - TCU SBL Numbering in A9120 BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108Table 37: Number of TS available in one Abis Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110Table 38: Number of Required TS versus TRX Number and Sub-Multiplexing Type . . . . . . . . . . . . . . . . . . . 111Table 39: Example of FR/DR Ratios According to Cell Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
3BK 17422 5000 PGZZA Ed.06b 7 / 162
-
Tables
Table 40: Numbering Scheme on BSC-Ater/Atermux/TC Ater/A Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 41: Numbering Scheme on A9120 BSC Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119Table 42: Numbering Scheme on G2 TC Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120Table 43: SS7, Atermux, DTC and Ater Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123Table 44: GPU Atermux Connections Example Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126Table 45: Ratio of Mixing CS and PS Traffic in Atermux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
8 / 162 3BK 17422 5000 PGZZA Ed.06b
-
Preface
PrefacePurpose This document describes the configuration rules for release B8 of the Alcatel
BSS. It describes the possible BSS configurations supported in release B9, anddescribes the new equipment in this release and the corresponding impact onthe various interfaces. Note that the OMC-R, RNO, NPA and LASER productsare beyond the scope of this document; refer to the appropriate documentationfor more information about these products.
Whats New In Edition 06bUpdate made in Extended Cell Configuration (Section 3.2.2.3) due to systemevolution.
In Edition 06Creation from doc version to.xml.Introduction of A9130 MFS in GPRS General Dimensioning and Rules (Section2.3.2), MFS Configuration (Section 6)Introduction of A9130 BSC Evolution in BSC Configuration (Section 4),Impedance (Section 7.2), Overview (Section 7.3.1), Qmux Bus (Section 7.4.2),RSL Reshuffling Algorithm (Section 7.6.3), Cross-Connect Use on Abis (Section7.6.4), Numbering Scheme on A9130 BSC Evolution-Ater/Atermux/TC Ater/AInterface (Section 8.4), SBLs Mapping on HW Modules in A9130 BSC Evolutionversus A9120 BSC (Section 7.6.6), TCU Allocation Evolution in A9130 BSCEvolution (Section 7.6.7), Rules (Section 3.13.2), Solutions (Section 10.3).PS is supported in extended cell. Plus other additional rules regarding theextended cells in Cell Types (Section 3.12.1), Extended Cell Configuration(Section 3.2.2.3)Editorial updates in chapters :New B9 Features and Impacted Sections (Section1.6), GPRS Configurations (Section 2.3.1), GPRS General Dimensioning andRules (Section 2.3.2), Rules (Section 2.5.3), A9130 BSC Evolution BoardConfigurations (Section 4.2.2.1), Centralized Mode (Section 6.1.3.2), MFSArchitecture (Section 6.2.1), MFS Clock Synchronization (Section 6.2.3)Update chapter with BTS number on A9130 BSC type 1A9130 Capabilities(Section 4.2.3)
In Edition 05
3BK 17422 5000 PGZZA Ed.06b 9 / 162
-
Preface
Overall document quality was improved following an editorial review.
In Edition 04A new feature allows the usage of TREs at their real power. More details inCell Types (Section 3.12.1), GMSK Output Power (Section 2.5.2.1), Rules(Section 2.5.3).The secured single Gb details are included in chapters Gb Configuration(Section 9.2) and MFS Clock Synchronization (Section 6.1.3).
In Edition 03Editorial review
In Edition 02Creation from doc version to.xml
Audience This manual is for people requiring an in-depth understanding of theconfiguration rules of the Alcatel BSS:
Network decision makers who require an understanding of the underlyingfunctions and rules of the systemIincluding:
Network plannersTechnical design staffTrainers.
Operations and support staff who need to know how the system operates innormal conditionsIncluding
OperatorsSupport engineersMaintenance staffClient Help Desk personnel.
This document can interest alsothe following teams:
Quality Acceptance First-OffCellular OperationsTechnical Project ManagersValidationMethods.
10 / 162 3BK 17422 5000 PGZZA Ed.06b
-
Preface
Assumed Knowledge The document assumes that the reader has an understanding of:
GSMGPRS
Mobile telecommunications.
3BK 17422 5000 PGZZA Ed.06b 11 / 162
-
Preface
12 / 162 3BK 17422 5000 PGZZA Ed.06b
-
1 Introduction
1 Introduction
Introduction gives a brief mentioning of synonymus of terms and a firstapproach of the Alcatel BSS, its equipments and features.
3BK 17422 5000 PGZZA Ed.06b 13 / 162
-
1 Introduction
1.1 BSS Equipment NamesThe following table lists the Alcatel commercial product names and thecorresponding Alcatel internal names.
Note: The names used in this document are those defined for internal use in Alcatel,and not the commercial product names.
Alcatel Commercial Product Name Alcatel Internal Name
Evolium A9100 G3, G3.5, G3.8, G4.2 BTS
Evolium A9110 M4M
Evolium A9110-E M5M
A9135 MFS AS800, DS10 RC23, DS10 RC40
A1353-RA OMC-3
A9125 A9125 Compact TC
A9120 G2 BSC
A9130 BSC Evolution A9130 BSC Evolution
A9130 MFS Evolution A9130 MFS Evolution
Table 1: BSS Equipment Names
1.2 Supported Hardware Platforms, Restrictions and RetrofitsThe following table lists the Alcatel hardware platforms supported in by theBSS, and corresponding restrictions and retrofits.
Equipment B9 Support Retrofit Required
BSC
A9120 BSC Yes
A9130 BSC Evolution Yes
TC
G2 TC Yes
A9125 Compact TC Yes
BTS Evolium
M4M, M5M Yes
G3, G3.5 Yes
14 / 162 3BK 17422 5000 PGZZA Ed.06b
-
1 Introduction
Equipment B9 Support Retrofit Required
G4 (G3.8, G4.2) YesG2 BTS
G2 Yes *
G1 BTS
G1 Mark II Yes *
MFS
MFS / AS800 Yes
MFS / DS10 ** Yes
MFS / DS10 *** Yes
MFS A9130 Yes
* : For BTS G1 and G2 only DRFU configuration is supported. BTS G1 is not supported at all for A9130 BSC Evolution.** : DS10 with network mirroring disks RC23*** : DS10 with local disks RC40Table 2: Supported Hardware Platforms, Restrictions and Retrofits
1.3 Platform TerminalsThe Alcatel BSS supports the Windows XP and Windows 2000 OperatingSystems (OS).
1.4 Release MigrationMigration from release B8 to release B9 infers the succession of the OMC,MFS and BSC.
1.5 BSS UpdatesNo hardware upgrades are required.
1.6 New B9 Features and Impacted SectionsThe following table lists the new B9 features, and provides links to impactedsections of this document.
New B9 Features Impacted Sections
GCH Statistical Multiplexing Rules (Section 2.5.3)Autonomous Packet ResourceAllocation
GPRS (Section 3.6.2)
3BK 17422 5000 PGZZA Ed.06b 15 / 162
-
1 Introduction
New B9 Features Impacted Sections
HCM Improvements (TRX/RSL andTRE/TCU)
TCU/RSL & TRX/RSL Mapping (Section B.2.2)
Preparation for Complete CellIdentification
PLMN Interworking (Section 2.6)
Up to 64 cell reselection adjacenciesper cell
PLMN Interworking (Section 2.6)
Enhanced Transmission ResourceManagement
Definitions and Prerequisites (Section 2.5.1)
Enhanced support of EGPRS in uplink Definitions and Prerequisites (Section 2.5.1), Rules (Section2.5.3)
Enhanced E-GSM band handling GPRS General Dimensioning and Rules (Section 2.3.2), EvoliumBTS Configuration (Section 3.2.2), G1 BTS (Section 3.4),Frequency Band Configuration (Section 3.7)
Secured single Gb GPRS General Dimensioning and Rules (Section 2.3.2)Unbalancing TRX Output Power perBTS sector
GMSK Output Power (Section 2.5.2.1), Cell Types (Section3.12.1), Rules (Section 2.5.3)
New platform introduction A9130 MFSEvolution
GPRS General Dimensioning and Rules (Section 2.3.2), MFSConfiguration (Section 6)
New platform introduction A9130 BSCEvolution and rack sharing
BSC Configuration (Section 4), Impedance (Section 7.2),Overview (Section 7.3.1), Qmux Bus (Section 7.4.2), RSLReshuffling Algorithm (Section 7.6.3), Cross-Connect Useon Abis (Section 7.6.4), Numbering Scheme on A9130 BSCEvolution-Ater/Atermux/TC Ater/A Interface (Section 8.4), SBLsMapping on HW Modules in A9130 BSC Evolution versus A9120BSC (Section 7.6.6), TCU Allocation Evolution in A9130 BSCEvolution (Section 7.6.7), Rules (Section 3.13.2),Solutions(Section 10.3)
PS in extended cell Cell Types (Section 3.12.1)
Table 3: New Features B9 and Impacted Items
16 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
2 BSS Overview
BSS Overview describes the Alcatel BSS, and corresponding features andfunctions.
The GSM Radio System (GRS) is a set of hardware and software equipmentprovided by Alcatel to support the radio part of the GSM network. The GRScomprises one OMC-R and one or more BSS. The OMC-R supervises oneor more BSS.The BSS provides radio access for Mobile Stations (MS) to the PLMN. Thereare one or more GRS per PLMN.The following figure shows a BSS with GPRS. All BSS operating over thefield are with/without data service.
3BK 17422 5000 PGZZA Ed.06b 17 / 162
-
2 BSS Overview
Figure 1: BSS with GPRS
The different Network Elements (NE) within the BSS are:The Base Station Controller (BSC)The Transcoder (TC)The Base Transceiver Station (BTS)The Multi BSS Fast packet Server (MFS).
The BSS interfaces are:
The Um interface (air or radio interface), between the MS and the BTSThe Abis interface, used to connect the BTS to the BSC
The Atermux interfaceused to connect:
The BSC to the TC and/or the MFSThe MFS to the TC
The A interface, used to connect the TC to the MSC
18 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
The Gb interface, used to connect the MFS to the SGSN (directly, or throughthe TC and the MSC).
Note: The Gs interface, between the MSC and the SGSN, is not described in thisdocument, as it is not considered to be part of the BSS. For more informationabout this interface, refer to the BSS System Description.For specific information about the LCS dedicated interfaces, refer to LCSin the BSS (Section 2.4).Given that the transmission architecture depends on GPRS, there are twopossible transmission architectures:
Transmission architecture with Circuit Switched (CS) onlyTransmission architecture with CS and Packet Switched (PS).
3BK 17422 5000 PGZZA Ed.06b 19 / 162
-
2 BSS Overview
2.1 Transmission Architecture with CS OnlyThis section provides information about static Abis only.The following figure shows the overall transmission architecture with CS only,inside the BSS.
Figure 2: Transmission Architecture with CS Only
The transmission interfaces are:
The Abis interface, between the BIE BTS and the BIE BSC
The Ater interface, between the SM and the DTC inside the BSC, andbetween the SM and the TRCU inside the TC
The Atermux interface, between the BSC-SM and the TC-SM
The A interface, between the TRCU and the MSC.
The Abis, Ater, Atermux and A interfaces are structured in 32 time slots (TS),each of which is composed of 8 bits at 64Kbit/s, resulting in a 2048 Kbit/sE1 digital hierarchy.
20 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
The TS are numbered from TS0 to TS31. Each 64 Kbit/s TS takes place in onebyte, sized of 8 bits numbered from 1 to 8.
Note: Microwave equipment is external to and independent of Alcatel transmissionequipment, however, in some cases, the microwave can be housed in thetransmission equipment rack and in the BTS.
2.2 Transmission Architecture with CS and PSPS is directly linked to GPRS and related MFS platforms.The following figures represent the MFS with its physical interfaces, whenconnected to the network.
Figure 3: Transmission Architecture with CS and PS (1)
Figure 4: Transmission Architecture with CS and PS (2)In addition to the interfaces defined in Transmission Architecture with CS Only(Section 2.1), the following MFS physical interfaces are used:
The MFS-BSC interface, which is the Atermux interface (a 2Mbit/s PCM linkcarrying 32 TS at 64Kbit/s). The Atermux interface can be fully dedicatedto GPRS (only PS conveyed), or mixed CS/GPRS. In this case, the CSchannels (called CICs) coexist with GPRS channels (called GICs) onthe same link.
3BK 17422 5000 PGZZA Ed.06b 21 / 162
-
2 BSS Overview
The MFS-TC interface, which is also a 2Mbit/s PCM link carrying CS only,GPRS only, or mixed CS/GPRS channels. The Gb interface can be routedthrough the TC for SGSN connection. While GSL is used between BSC andMFS for signaling and not for traffic, the GCH is used between the BTS andMFS. There are up to 4 tributaries multiplexed in one Atermux.
The MFS-SGSN interface, which carries the Gb interface when there is adedicated MFS-SGSN link. This interface can cross a Frame Relay networkor not (direct connection MFS-SGSN).The MSC-SGSN interface, which carries the Gb interface to/from the MFSwhen there is no dedicated MFS-SGSN link. This interface can cross aFrame Relay network or not (direct connection MSC-SGSN).The MFS-OMC-R interface, which is a Q3 and FTP interface.
Note: The MFS can be directly connected to the MSC (that is, without crossing theTC) for cabling facilities, however this still results in an MFS-SGSN interface,because the MSC only cross-connects the GPRS traffic.
2.3 GPRS in the BSSThe MFS enables GPRS in the network. The following figure shows the locationof the MFS in the network.
Figure 5: MFS in the Network
2.3.1 GPRS ConfigurationsThe introduction of GPRS into the BSS basically requires the followingmodifications:
The introduction of the Packet Control Unit (PCU). The PCU controls theGPRS activities for one Alcatel BSS.
The introduction of the Gb interface termination function.
22 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
The Alcatel approach for the implementation of GPRS is to group the PCUand Gb termination functions of several BSS into one new NE called theMFS (MFS-A9135).The following figure shows the GPRS NEs, interfaces and channels.
Figure 6: GPRS NE, Interfaces and Channels
Within the Alcatel BSS, two communication planes are used:
The transmission planeThe PCU at the MFS converses with the CCU on the BTS side, via GCH,transparently through the BSC.
The control plane.The following two signaling interfaces are used:
The GPRS Signaling Link (GSL) between the MFS and BSC. This link isused for co-ordination between the BSC and the PCU, mainly for GPRScapacity on demand, and for GPRS paging, access request and accessgrant when the CCCH is used for GPRS.The Radio Signaling Link (RSL) between the BTS and the BSC. TheRSL is mainly used for GPRS paging, access request and access grant,when the CCCH is used for GPRS.
The following configurations are supported:
The Gb interface can be routed via the G2 TC and A9125 Compact TC tothe SGSN across the MSC
The MFS can be connected to one OMC-R only
The MFS and all connected BSS are managed by the same OMC-R. TheBSS connected to the same MFS can be linked to different MSC.
3BK 17422 5000 PGZZA Ed.06b 23 / 162
-
2 BSS Overview
2.3.2 GPRS General Dimensioning and Rules
O:OperatorChoiceS:SystemCheck
Maximum Quantity (No MultipleGPU)
Maximum Quantity (MultipleGPU*)
BSS per A9135MFS
O, S 22 22
BSS per A9130MFS
O, S 21 21
BSS per GPU S 1 1
GPU per BSS O, S (onmaximumvalue)
1 6 GPU per BSS (committed value)
GPU per A9135MFS
O, S 24=2(11+1) 32=2*(15+1) (DS10)24=2*(11+1)(AS800)
GPU perA9130MFS 1 shelf
O, S 9+1/8+1 9+1/8+1
GPU perA9130MFS 2shelfs
O, S 21+1 21+1
Number of GCHsimultaneouslyallocated per GPU
S 240 240
Number of GCHsimultaneouslyallocated per GP
S 1560 1560
Number of PDCHreached on GP
S 960 PDCH CS-2912 PDCH MCS-1784 PDCH CS-4/MCS-5520 PDCH MCS-6390 PDCH MCS-7312 PDCH MCS-9
960 PDCH CS-2912 PDCH MCS-1784 PDCH CS-4/MCS-5520 PDCH MCS-6390 PDCH MCS-7312 PDCH MCS-9
Atermux A9120BSS-A9135MFS
O 8 17 (minimum (ater Mux-1,nb.GPU*8))
Atermux A9120BSS-A9130MFS
O 6 17 (minimum (ater Mux-1,nb.GPU*6))
Cells / GPU S 264 264
24 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
O:OperatorChoiceS:SystemCheck
Maximum Quantity (No MultipleGPU)
Maximum Quantity (MultipleGPU*)
Cells / MFS S 2000 2000
Frame Relay BC /GPU
O, S 120 120
BVC per GPU S 264 264
TRX with PDCHper Cell
O,S 16 16
Allocated PDCHper TRX
S 8 8
NSE per A9135MFS
O, S 22=2*(11) 30=2*(15)(DS10)22=2*(11)(AS800)
NSE perA9130MFS
O, S 21 21
GSL per BSC O 4GSL/GPU 4 GSL/GPU: up to 12 GSL/BSCminimum (12, 4*nb.GPU)
Allocated GICs perBSC
480=4*120 2000
BVC-PTP 240 240
NS-VC per NSE O, S 120 120
Bearer Channelper MFS
O, S 300 300
Bearer ChannelPer PCM
O, S 31 31
PVC per BC S 1 1
* : GPU concerns the logical unit, and GP is expressed for A9130 MFS.Table 4: GPRS General Dimensioning
The following rules and recommendations apply:
CS traffic going through the MFS is transparently connected. Thecross-connection capacity in the MFS is at the 64k TS level.
Gb traffic going to the TC is routed transparently at the TC site
3BK 17422 5000 PGZZA Ed.06b 25 / 162
-
2 BSS Overview
There is no GPRS traffic directly on the BSC-TC Atermux, as there is noway to connect GPRS TS between the BSC and the MFS through the TC
Maximum 1 GSL per Atermux. The GSL is located on TS28 of the 2ndtributary
To avoid complexity, the capacity to drop 64 Kbit/s TS in the TC (e.g. for theX.25 OMC-R link) is not used to drop Gb trafficWhen frame relay (Gb) is supported on a PCM, bearer channels on thisPCM are organizedas follows:
64 Kbit/s TS (up to 31 independent TS)Nx64 Kbit/s or bundles of TS (a bundle of TS is a list of contiguous PCMTS belonging to the same PCM). One exception that can break the TScontiguity is the TS16 for SS7).Whole 2Mbit/s PCM for the MFS/SGSN interface only.
To maximize the TS bundle for the Gb, Atermux TS routed transparently atTC site are supported by a single tributary at A interface
CS traffic coming from different Atermux (of a same BSC) cannot be mergedat the MFS site to go to the TC
The GPRS Preference Mark (GPM) is removed after migration in release B8(it no longer exists in release B8). The value "0" of TRX Preference Mark(TPM) in release B8 means that the concerned TRX is PS capable.GPRS is not supported by the G1 band TRXs, nor by the inner zone TRXsof a concentric or a multiband cell
GPRS is not supported on extended cells
A dynamic SDCCH TS cannot be used to carry GPRS traffic
The setting of a new parameter (i.e. EN_FAST_INITIAL_GPRS_ACCESS) must interact with the MIN_PDCH parameter and the number of themaster channels in the cell. It must fulfill the following rule: MIN_PDCH -Nb_TS_MPDCH > 0 if EN_FAST_INITIAL_GPRS_ACCESS = enabled.
If there are several FHS, all PS TRX have the same FHS
In BBH, the FHS for PS TRX contains the BCCH TRX, if there is a masterchannel.
The AS800/DS10 MFS supports only 8 BSC/MFS links (and 32 gicGroupinstances per GPU). The A9130 MFS supports up to 13 BSC/A9130 MFSlinks (and up to 52 gicGroups instances per GP).In case of A9130 BSC Evolution mono GPU do not configured more than448 TRX on this GPU.
The following figures show an example link configuration (3/4 GSM& 1/4GPRS Atermux 4:1 mapping).
26 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
MFS-TC Atermux Interface 16 Kbit/s Ater Interface Trib. 1,2,3,4 A InterfaceTrib. 1,2,3,4
3BK 17422 5000 PGZZA Ed.06b 27 / 162
-
2 BSS Overview
Figure 7: Example 1 of a Link Configuration: 3/4 GSM& 1/4 GPRS Atermux 4:1 mapping
28 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
3BK 17422 5000 PGZZA Ed.06b 29 / 162
-
2 BSS Overview
Figure 8: Example 2 of a Link Configuration: 3/4 GSM& 1/4 GPRS Atermux 4:1 mapping
2.4 LCS in the BSS
2.4.1 PrerequisitesLocation Services (LCS) are new end-user services which provide thegeographical location of an MS (i.e. longitude, latitude and optionally altitude).LCS are applicable to any target MS, whether or not the MS supports LCS, butwith restrictions concerning the choice of positioning method when LCS orindividual positioning methods are not supported by the MS.The LCS client resides in an entity (including the MS) within the PLMN, orin an entity external to the PLMN.LCS provides the position of the target MS. Depending on the positioningtechniques, some LCS functions reside in the MS.
2.4.2 Logical ArchitectureLCS support requires new functions in the network sub-system, and optionally,on the radio side, depending on the positioning technique and on the networksynchronization.These new functions are respectively:
The Gateway Mobile Location Center (GMLC)The Serving Mobile Location Center (SMLC).
The following figure shows the generic LCS logical architecture.
30 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
Figure 9: Generic LCS Logical Architecture
As shown above:
The GMLC is the first NE serving external Location Application (LA) accessin a GSM PLMN. The GMLC requests routing information from the HomeLocation Register (HLR) via the Lh interface. After performing registrationauthorization, it sends positioning requests to the MSC and receives finallocation estimates from the MSC or the SGSN via the Lg interface.
The SMLC is the NE which serves the client. The SMLC manages theoverall coordination and scheduling of the resources required to performingMS positioning. The SMLC calculates the final location estimate andaccuracy, and controls a number of LMUs to obtain the radio interfacemeasurements required to locate the MS in the area it serves. The SMLCis connected to the BSS (via the Lb interface).
2.4.3 Physical ImplementationThe following physical implementation rules apply:
For hardware, the existing GPU boards support the SMLC function. AnA-GPS server is required for some LCS positioning method implementation.
For software, the GPU software supports both GPRS functions and SMLCfunctions, and is handled as a whole (there is no dedicated software for eachfunction), in that the LCS software is a module on top of the GPRS software.
3BK 17422 5000 PGZZA Ed.06b 31 / 162
-
2 BSS Overview
For a BSC connected to several GPUs, the SMLC function for the whole BSSis supported by the current pilot GPU and only by this GPU (the pilot GPUbeing the GPU handling procedures at the BSS level). When the pilot GPU isre-elected (e.g. following the loss of all GSLs on the current pilot GPU), theSMLC function restarts on the new pilot GPU.
2.4.4 Functional RequirementsThe Alcatel BSS supports the LCS feature, which implies:
The SMLC, a new functional NE in the BSS, is integrated into the MFS andconfigured by the OMC-R. (MFS - GPRS services - several BSCs SMLC - LCS services - same BSCs).A new Alcatel proprietary interface (BSCLP, or Lb) for LCS signalingprotocols between the BSC and the SMLC (i.e. the MFS)Support of the followingpositioning methods:
The Timing Advance (TA) positioning method, which implies the deliveryof Cell Id and TA. The TA positioning method regroups several distinctmethods (Cell Id only (CI), Cell Id + TA (CI+TA)). The TA positioningmethod is the only method applicable to all the MS (regardless ofwhether they support LCS or not).The conventional GPS positioning method, based on the GPS locationestimation performed in the MS itself and provided to the SMLCThe Assisted GPS (A-GPS) positioning method, which is split into MSAssisted A-GPS and MS Based A-GPS positioning methods, dependingwhere the location calculation is processed (in the network or in the MS):
MS Assisted A-GPSThe MS receives GPS Assistance Data from the SMLC (which hasreceived the data previously from the external GPS server), performsGPS measurements, and returns the resulting GPS measurements tothe SMLC. The SMLC provides these GPS measurements to theexternal GPS server, which computes the MS location estimate.
MS Based A-GPSThe MS receives GPS Assistance Data from the SMLC (which hasreceived the data previously from the external GPS server), performsGPS measurements and location calculation, and returns its locationestimation to the SMLC.For the last two positioning methods, a GPS-capable MS is required.
New signaling messages on the A interface for LCS, as location requestsare received from the core network
New signaling messages on the radio interface, in the case of ConventionalGPS and A-GPS positioning methods
A new Alcatel proprietary interface (SAGI) between the SMLC (i.e. the MFS)and an external GPS server in the case of A-GPS positioning methods.
32 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
2.4.5 GPS LCSIf a high accuracy is required, GPS positioning method(s) are preferred, whenpossible.The following figure shows the interface towards the external A-GPS server.
Figure 10: SAGI Physical Architecture
The communication between a pilot GPU supporting the SMLC function of agiven BSS and the external GPS server is supported by:
An Ethernet LAN within the MFS (which already exists, except that 2additional Ethernet cables must be added to connect the hubs to theexternal router)The customer network, the adaptation of the IP traffic (TCP/IP over Ethernet)to the format of the customer network being under the responsibility of anexternal router ( Alcatel OmniAccess 512 which is NOT capable of allowingthe MFS to present only one IP address to the A-GPS Server).
A router is used, regardless of whether the server and the MFS are collocatedor not collocated.The following figure shows the impact on hub connectivity.
3BK 17422 5000 PGZZA Ed.06b 33 / 162
-
2 BSS Overview
Figure 11: Impact on Hub Connectivity
Each hub has 24 slots to plug in the Ethernet cables.If the MFS is equipped with only one telecom subrack on a given hub, up to 22slots (15 GPU + 1 spare GPU + 2 JBETI + 2 control stations + 1 PC + 1 router)can be used, which means 2 free slots on this hub.If the MFS is equipped with two telecom subracks on a given hub, up to 23 slots(15 GPU + 1 spare GPU + 2 JBETI + 2 control stations + 1 PC + 1 HUB + 1router) can be used, which means one free slot on this hub.
2.4.6 BSS and Cell ConfigurationLCS is an optional feature in the Alcatel BSS. This feature can be blocked bythe manufacturer. When provided to the customer, LCS can be enabled ordisabled by the operator at cell level.To have LCS support for a cell, the operator must:
Attach the BSC to an MFS in order to declare the BSC in the MFS. Thisleads to the download of the BSS configuration (GPRS and LCS-relatedattributes of the BSS, even if GPRS or LCS is not supported) in the MFSProvide the geographical coordinates of the cell
Activate GPRS for the cell (i.e. set the MAX_PDCH to > 0, so that the cell islocked for GPRS if the operator does not want to have GPRS running onthis cell)Configure all the required transmission resources (Ater and Gb resources)on the GPU(s) connected to the BSCActivate LCS (by setting the EN_LCS flag, the common BSC/MFSparameter, to true ) on the BSS handling the cellEnable at least one of the following flags: EN_CONV_GPS,EN_MS_ASSISTED_AGPS, EN_MS_BASED_AGPS
Enable the EN_SAGI flag, to indicate whether the SAGI interface isconfigured for the BSS (physical and transport level configuration) forGPS LCS only.
34 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
Ater resources are required (GSL, Gb).The OMC-R provides centralized management of the LCS.
2.4.7 Traffic ModelLCS traffic support is provided for as a short-term requirement that will bemet in release B8, and as a long-term objective that the initial B8 systemarchitecture support, as follows:
Long-term objective:38 location requests/s per 6 BSC configuration (the BSC can handle up to1900 Erlang) and 680 location requests/s per MFS. This traffic is basedon the assumption of one location request per call (mean call duration =80 s). This traffic requirement will remain unchanged when replacing CStraffic by PS traffic.
Note: With regard to the long-term objective:The consensus is to accept one location request per CS call, whichleads to 38 location requests/s for a 1900 Erlang (448 TRX) BSC and acall duration of 50 s.
The capacity of an MFS being limited to 8000 TRX, the total number oflocation requests/s to be processed is limited to 680.
Short term requirement:3.8 location requests/s per configuration 6 BSC, i.e. 68 location requests/sper MFS.
2.4.8 RulesThe following rules apply:
LCS is not supported in the PS domain
Network Measurement Results (NMR) are not supported with LCSA-GPS positioning methods can be used only if the new SAGI interfacehas been installed
LCS is supported on extended cells if it is in the GPRS locked administrativestate
An MFS with a router in front presents only one IP address to the GPSserver. Reciprocally, the GPS server presents only one IP address to arouter in front of the MFS
The router is external to the MFS, which implies that it is not supervised bythe MFS. The declaration of SAGI interface is supported by a EN_SAGIflag defined on a per BSS basis.
2.5 HSDS in the BSS
2.5.1 Definitions and PrerequisitesThe High Speed Data Service (HSDS) consists of:
3BK 17422 5000 PGZZA Ed.06b 35 / 162
-
2 BSS Overview
A basic service to offer CS3 and CS4 for GPRS and MCS1 to MCS9for EGPRS (two optional features)Additional functionssuch as:
Adapting radio resource allocation in order to take into account E-GPRSMSThe ability to avoid Ater blocking.
EDGE consists of two concepts defined by ETSI:
ECSD
E-GPRS.
EGPRS is 2.5 to 3 times more efficient than GPRS, regardless of the frequencyband, the environment and the mobile velocity.EDGE is available in Evolium BSS with minimum impact on the network.There is no hardware impact on the MFS and the BSC, and the Evolium BTSis EDGE- ready simply by plugging in the EDGE-capable TRX where andwhen it is needed.
2.5.1.1 GPRS Coding SchemesTwo new coding schemes are proposed for GPRS in release B9:
CS-3
CS-4.
The following table lists the coding schemes and the corresponding modulationtypes and maximum transmission rates.
Scheme Modulation Maximum Rate [Kbps] perRadio TS
CS-4 GMSK 20
CS-3 GMSK 14.4
CS-2 GMSK 12
CS-1 GMSK 8
Table 5: GPRS Coding Schemes
2.5.1.2 E-GPRS Modulation and Coding SchemesE-GPRS enables the support of data transmission at a bit rate which exceedsthe capabilities of GPRS.E-GPRS relies on new modulation and coding schemes on the air interface,allowing a data throughput which is optimized with respect to radio propagationconditions (referred to as link adaptation).The basic principle of link adaptation is to change the Modulation and CodingSchemes (MCS) according to the radio conditions. When the radio conditions
36 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
worsen, a more protected MCS (more redundancy) is chosen for a lowerthroughput. When the radio conditions become better, a less protected MCS(less redundancy) is chosen for a higher throughput.Nine modulation and coding schemes are proposed for enhanced packet datacommunications (E-GPRS), providing raw RLC data rates ranging from 8.8kbit/s (the minimum value under the worst radio propagation conditions perTS) up to 59.2 kbit/s (the maximum value achievable per TS under the bestradio propagation conditions). Data rates above 17.6 kbit/s require that 8-PSKmodulation is used on the air interface, instead of the regular GMSK.The following table lists the coding schemes and the corresponding modulationtypes and maximum transmission rates.
Scheme Modulation Maximum Rate [Kbps] perRadio TS
MCS-9 8-PSK 59.2
MCS-8 8-PSK 54.4
MCS-7 8-PSK 44.8
MCS-6 8-PSK 29.6 A/27.2 A padding
MCS-5 8-PSK 22.4
MCS-4 GMSK 17.6
MCS-3 GMSK 14.8 A/13.6 A padding
MCS-2 GMSK 11.2
MCS-1 GMSK 8.8
Table 6: EGPRS Modulation and Coding Schemes
2.5.1.3 HSDSHSDS provides support for GPRS with CS1 to CS4, and for E-GPRS withMCS1 to MCS9.There are 3 families of modulation and coding schemes:
Family A: MCS3, MCS6, MCS8 and MCS9
Family B: MCS2, MCS5 and MCS7
Family C: MCS1 and MCS4.
Each family has a different unit of payload:
37 bytes: family A
34 bytes: family A padding (MCS3, MCS6 and MCS8)28 bytes: family B
22 bytes: family C.
3BK 17422 5000 PGZZA Ed.06b 37 / 162
-
2 BSS Overview
The different code rates within a family are achieved by transmitting a differentnumber of payload units within one radio block.When 4 payload units are transmitted, these are split into 2 separate RLCblocks (i.e. with separate sequence numbers).When a block has been retransmitted with a given MCS, it can be retransmitted(if needed) via ARQ with a more robust MCS of the same family.The following figure shows the choice of modulation schemes.
Figure 12: Choice of Modulation Scheme
The choice of modulation schemes is based on the measurement of thebit error probability (BEP).The coding scheme and the radio modulation rates are modified to increase thedata traffic throughput of a given radio TS. This implies that the increase ofthroughput is handled on the Abis and Ater interfaces (previously, for each radioTS in use, only a 16kb/s nibble was allocated on both interfaces).
2.5.1.4 Ater interfaceIn order to handle a throughput higher than 16Kb/s on the Ater interface,several Ater nibbles are dynamically allocated by MFS Telecom.
2.5.1.5 Abis InterfaceOn the Abis interface, to handle a throughput higher than 16Kb/s, severalAbis nibbles are also used. The configuration is dynamic for TRX insidethe same BTS.A number of 64k EXTS (Extra TS) are defined for each BTS by O&M. Thisgroup of TS replaces the number of transmission pool types used previously.
38 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
Due to the increase in Abis resource requirements, a single Abis link may notbe enough to introduce HSDS into a large BTS configuration. In this case, asecond Abis link is required (see Two Abis Links per BTS (Section 7.9) ).
2.5.1.6 M-EGCHThis term is used to refer to a link established between the MFS and the BTS.One M-EGCH is defined per TRX.
2.5.1.7 Enhanced Transmission Resource ManagementA dedicated manager sequences the GCH establishment, release, redistributionor pre-emption procedures.The transmission resource manager is on the MFS/GPU level. It handles bothAbis and Ater resources (GCH level).It is in charge of:
Creating and removing the M-EGCH links
Selecting, adding, removing, and redistributing GCHs over the M-EGCHlinks
Managing transmission resource preemptions
Managing Abis and/or Ater congestion states
Optionally, monitoring M-EGCH links usage, depending on the (M)CS oftheir supported TBFs (UL and DL).
2.5.1.8 Abis Nibble Sharing RulesTo ensure that each cell of a given BTS is able to support PS traffic at all times,there must be a minimal number of Abis nibbles for every cell in the BTS.
2.5.1.9 Ater Nibble Sharing RulesA given amount of Ater transmission resource is allocated per GPU. Afterwards,this Ater transmission resource is shared among the 4 DSPs of the GPU,via the GPU on-board Ater switch.Only 64K Ater TS are handled at GPU level between the DSPs. Therefore,a 64K Ater TS is moved from one DSP to another if, and only if, all of itsfour 16K Ater nibbles are free. This is the unique restriction concerning Aternibble sharing at GPU level.
2.5.2 Transmission Power
2.5.2.1 GMSK Output PowerGMSK is a constant amplitude modulation.
2.5.2.2 8-PSK Output PowerFor one given TRE, the maximum output power is lower in 8-PSK than in GMSKbecause of the 8-PSK modulation envelope which requires a quasi-linearamplification.The TRE transmit power in 8-PSK does not exceed the GMSK transmit powerin the sector and in the band.8-PSK is a varied digital phase modulation.Leveling of 8-PSK Output Transmission Power is new in release B8.
3BK 17422 5000 PGZZA Ed.06b 39 / 162
-
2 BSS Overview
For a TRE, there is a major difference in the output transmission power betweenthe GMSK and the 8-PSK modulation. This is shown in the following table.
G4 TRE Medium Power G4 TRE High Power
GMSK (CS1-CS2/MCS1-MCS4) 46.5 dBm 47.8 dBm
8-PSK (MCS5-MC9) 41.8 dBm 44.0 dBm
Table 7: GMSK and 8-PSK Transmission Power Differences
Note that the operator is allowed to allocate the E-GPRS TBF on the BCCHTRX, and the BCCH frequency must have a quite stable radio transmissionpower.Due to this constraint, the 8-PSK output transmission power is not leveled persector, in order to effectively exploit the TRE capability, and the E-GPRS TRXsare preferably mapped to a TRE with the best 8-PSK capability.The Modulation Delta Power is the difference between the GMSK output powerof the sector for the TRE band, and the 8-PSK output power of the TRE.According to the 8-PSK delta power value, a TRE is called "High Power" or"Medium Power". 8-PSK High Power Capability is true if Modulation DeltaPower is less than 3 dB.
2.5.3 RulesThe following rules apply:
TCU Allocation:Extra Abis TS are allocated only on the FR TCURSL, OML and TCH are mapped on a TCU, regardless of extra Abis TSExtra Abis TS are moved automatically from one TCU to another.
Allocation priorities (from highest to lowest)PS TRX/TRE are ordered according to the following rules:
PS allocation is preferred on the BCCH TRXThe TRE hardware capabilityThe DR TRE configurationThe maximum PDCH group criterionThe TRX Identifier.
TRX TRE mapping:G4 TRE or M5M is preferentially used for PS allocationTRE with 8-PSK HP capability is preferentially used for PS allocationPS traffic is allocatedin priority to:
G4 TRE with 8-PSK HP capability
G4 TRE without 8-PSK HP capability
40 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
G3 TRE.
DR TRE is preferentially used for CS allocations. DR is reserved forCS trafficThe DR must be assignedin priority of:
G3 TRE
G4 TRE without 8-PSK HP capability
G4 TRE with 8-PSK HP capability.
TRE and TRX are classifiedaccording their characteristics:
Full-rate, high power, E-GPRS capable TRE
Dual-rate, high power, E-GPRS capable TRE
Full-rate, medium power, E-GPRS capable TRE
Dual-rate, medium power, E-GPRS capable TRE
Full-rate, non-E-GPRS capable TRE
Dual-rate, non-E-GPRS capable TRE
When PS_Pref_BCCH_TRX = True, then the TRX supporting theBCCH is mapped on the best TRE
3BK 17422 5000 PGZZA Ed.06b 41 / 162
-
2 BSS Overview
The TRE of the preferred class must be mapped to a TRX of thepreferred classIn the case where HSDS is not activated, only a reduced adjust isperformed, as shown below:
TRX ranking:PS capable TRXs are ranked according to the following criteria, forPS traffic
TRX supporting the BCCH, if PS_Pref_BCCH_TRX = True
TRX capability (E-GPRS capable, high power, then E-GPRS capable,medium power and finally, non-E-GPRS capable)Dual-rate capability (FR, then DR)Size of the PDCH group.
This ranking will be used in the reverse order for CS traffic
BTSA mix of the G4 TRE medium power and G4 TRE high power (that offersa higher output power useful for 8-PSK modulation) in the same EvoliumBTS is allowed.
PS Capability of BTSsOnly Evolium BTS (including Evolium Micro-BTS) support the HSDS, butthe PS capability is function of the TRE generation. This is shown inthe following table.
TRE generation PS Capability
G3 TRE and M4M CS1 to CS4
G4 TRE and M5M CS1 to CS4 and MCS1 to MCS9
To support MCS1 to MCS9, an Evolium BTS must be upgraded withsome G4 TRE
42 / 162 3BK 17422 5000 PGZZA Ed.06b
-
2 BSS Overview
A mix of G3 and G4 TRE in the same Evolium BTS is allowed. From asoftware point of view, there are no specific rules that define the positionof G3 and G4 TRE: their position in the BTS rack is free
MFS capacity:The MFS capacity is defined by the maximum throughput of the GPUThe maximum throughput of the GPU isthe minimum of:
PPC maximum throughput
4 x DSP maximum throughput.
For example, for A9135 MFS, the maximum throughput for a DSP, in onedirection, is about 800 kbit/s for pure GPRS and 1 Mbit/s with E-GPRS(with some assumptions regarding MCS and CS distribution)
The support of 8PSK in UL is optional for the MS.
2.6 PLMN InterworkingA foreign PLMN is a PLMN other than the PLMN to which OMC-R internal cellsbelong. Only cells external to the OMC-R can belong to a foreign PLMN. Allinternal cells must belong to their own PLMN. Both OMC-R owned cells andcells which are external to the OMC-R can belong to the primary PLMN.The Alcatel BSS supports:
Incoming inter-PLMN 2G to 2G handovers
Outgoing inter-PLMN 2G to 2G handovers, as an optional featureThe operator can define handover adjacency links towards external cellsbelonging to a foreign PLMN, (i.e. handovers from a serving cell belongingto the primary PLMN towards a target cell belonging to a foreign PLMN).Inter-PLMN 2G to 2G cell reselectionsThe Alcatel BSS allows the operator to define cell reselection adjacencybetween two cells belonging to different primary PLMN (which musttherefore be owned by two different BSC).Multi-PLMN, as an optional featureThe Multi-PLMN feature allows operators to define several primary PLMN,in order to support network sharing (Tool Chain, OMC-R, MFS, Abistransmissions, and also BTS, via rack sharing). Inter-PLMN handovers andcell reselections between two different primary PLMN are supported.The BSC itself cannot be shared and therefore remains mono-PLMN (i.e. allBSC owned cells belong to the same primary PLMN).The Alcatel BSS supports several primary PLMN (at least one, up to four).An OMC-R therefore manages at least one (primary) PLMN and up to eightPLMN (four primary and four foreign). Both cell reselections and handoversare allowed between two cells which belong to different primary PLMN.The operator can define handover adjacency between two cells belonging todifferent primary PLMN (which must therefore be owned by two differentBSC).
3BK 17422 5000 PGZZA Ed.06b 43 / 162
-
2 BSS Overview
The OMC-R (and the Tool Chain) is by definition of the feature itself alwaysshared between the different primary PLMN. On the other hand:
The MFS can be shared
The BSC cannot be shared
The BTS can be shared up to the rack sharing level (no radio part sharing)The Abis transmission part can be shared
The transcoder part can be shared.
The outgoing inter PLMN handovers feature is a prerequisite for the multi-PLMNfeature.It is not allowed to modify the "PLMN friendly name" of a cell, even if the"Multi-PLMN" feature is active and several PLMN have been defined on theOMC-R side.The primary PLMN cannot be added, removed or modified online.Customers no longer need to ensure CI (or LAC/CI) unicity over all PLMNinvolved in their network.With regard to clock synchronization, the only constraint is that when theMFS is connected to different SGSN, these SGSN are not synchronizedtogether, therefore, central clocking and cascade clocking cannot be used onthe MFS side.
44 / 162 3BK 17422 5000 PGZZA Ed.06b
-
3 BTS Configurations
3 BTS Configurations
BSS Overview describes the Alcatel BSS, and corresponding features andfunctions.
The following figure shows the location of the BTS inside the BSS.
Figure 13: BTS in the BSS
3BK 17422 5000 PGZZA Ed.06b 45 / 162
-
3 BTS Configurations
3.1 BTS Generation SummaryThe following table lists the successive BTS generations, along with thecorresponding commercial name.
G1 BTS G2 BTS Evolium BTS Evolium Evolution
G1 BTS G2 BTS G3 BTS G4 BTS (*)
MK2 Mini Std G3 M4M G3.5 G3.8 G4.2 M5M MBS
* : Note that G3.8 and G4.2 are the TD used names for respectively Evolium Evolution Step 1 and Evolium EvolutionStep 2.
Table 8: BTS Generation Summary
The BTS are grouped into the following families:
A9110 BTS, which include the micro BTS M4M, and the A9110-E forM5M micro BTS
A9100 BTS, which include all Evolium BTS, but not the micro BTS.
3.2 Evolium BTS
3.2.1 Evolium BTS ArchitectureThe Evolium BTS is designed with the following three levels of modules tocover many cell configuration possibilities, including omni or sectored cellsconfigurations:
The antenna coupling level, which consists of ANX, ANY and ANC
The TRX, which is implemented as a TRE, and handles the GSM radioaccess
The BCF level implemented in the SUM, which terminates the Abis interface.
Note: The above-mentioned architecture does not include micro BTS.
3.2.2 Evolium BTS ConfigurationThe Evolium BTS family began with the G3 BTS, whose architecture isdescribed in Evolium BTS Architecture (Section 3.2.1).Further evolutions were introduced, with the G3.5 and G4 variants:
G3.5 BTS, which is a G3 BTS with new power supply modules
G4 BTS Step 1 (also referred to within TD as the G3.8), which is a G3.5BTS in whichthe following modules have been redesigned:
SUMA, which is the new SUM boardANC, which is a new antenna network combining a duplexer anda wide band combiner
46 / 162 3BK 17422 5000 PGZZA Ed.06b
-
3 BTS Configurations
New power supply modules which are compatible with BTS subracks.
G4 BTS Step 2 (also referred to within TD as the G4.2) introduces a newTRE with EDGE hardware capability,including:
CBO, which is the compact outdoor BTSMBS, which is provides multistandard cabinets withthe following G4.2 modules:
MBI3, MBI5 for Indoor
MBO1, MBO2 for Outdoor
The Evolium BTS family also includesthe two following micro BTS:
M4M
M5M.
3.2.2.1 Product PresentationThere are different types of Evolium cabinets:
The indoor cabinet, which exists in different sizes: Mini, Medi, MBI3 andMBI5
The outdoor cabinet, which exists in different sizes and packaging: Mini,Medi, CPT2, CBO, MBO1 and MBO2
3.2.2.2 Evolium BTS Rules and DimensioningThe following table lists the extension and reduction capacity rules for theEvolium BTS.
Extension / ReductionConfiguration
Physical Logical
Minimum Maximum Minimum
Evolium BTS 1 TRE Up to 12TRE1 to 6Sectors
1 TRE 1 TRE
3BK 17422 5000 PGZZA Ed.06b 47 / 162
-
3 BTS Configurations
Extension / ReductionConfiguration
Physical Logical
Minimum Maximum Minimum
M4MMicro-BTS
2 TRE Up to 6 TRE1to 6 Sectors
2 TRE 1 TRE
M5MMicro-BTS
2 TRE Up to 12TRE1 to 6Sectors
2 TRE 1 TRE
Table 9: Evolium BTS Minimum and Maximum Capacity
The following table summarizes the typical GSM 900, GSM 1800 and GSM1900 configurations.These configurations constitute only a subset of the possible configurations.
Network GSM 900 MHz GSM 1800 MHz, GSM 1900 MHz
Indoor /Outdoor
Indoor Outdoor Indoor Outdoor
Cabinetsize
Mini Medi Mini Medi Mini Medi Mini Medi
Numberof TRE1sector
1x2 to1x4
1x2 to1x12
1x2 to1x4
1x2 to1x12
1x2 to1x4
1x2 to1x12
1x2 to1x4
1x2 to1x12
2 sectors 2x1 to2x2
2x2 to2x6
2x1 to2x2
2x2 to2x6
2x1 to2x2
2x2 to2x6
2x1 to2x2
2x2 to2x6
3 sectors 3x1 3x1 to3x4
3x1 to3x2
3x1 to3x4
3x1 3x1 to3x4
3x1 to3x2
3x1 to3x4
Table 10: Typical GSM 900 and GSM 1800/1900 Configurations
The following table summarizes the typical Multiband 900/1800 BTSconfigurations.These configurations constitute only a subset of the possible configurations.
Network Multiband BTS or Multiband Cell
Cabinet size Medi
Number of TRE4 sectors 2x2 GSM 900 & 2x4 GSM 18002x4 GSM 900 & 2x2 GSM 1800
48 / 162 3BK 17422 5000 PGZZA Ed.06b
-
3 BTS Configurations
Network Multiband BTS or Multiband Cell
6 sectors 3x2 GSM 900 & 3x2 GSM 1800 (outdoor only)Diversity 4 sectors : Yes
6 sectors : Yes
Table 11: Typical Multiband Configuration G3 BTS
3.2.2.3 Extended Cell ConfigurationUp to 12 TRX CS+PS capable, including the BCCH TRX can be offered in eachcell (inner + outer).M4M and M5M do not support extended cell configurations.Only one extended cell per BTS is possible.Extended cell is not supported by SUMP.
3.2.2.4 Mixture of M5M and M4M BTSThe following 4 configurations rules are defined for pure M5M and M4M/M5Mmixed configurations:
A maximum of 3 hierarchic levels ( master, upper and lower slave ) areallowed
Each M4M upper slave terminates the master-slave link, which is theInter Entity Bus (IEB)M4M is not allowed in the lower slave position
M5M must be set as master in M4M/M5M mixed configurations.
3BK 17422 5000 PGZZA Ed.06b 49 / 162
-
3 BTS Configurations
3.2.2.5 Mixed configuration G3 and G4In case of mixed hardware configuration in a cell with both G3 and G4 TREsin the same cell, it is recommended to map to E-GSM TRX on G4 TRE andP-GSM TRX on G3 TRX.Under some conditions, the BSC does not guarantee that the PS TRXs havingthe highest priority for PS allocations are mapped on the G4 TREs.
3.3 G2 BTSThe following rules apply:
Only G2 BTS with DRFU are supported in release B8
The FUMO in G2 BTS must be replaced by the DRFU, before migration torelease B7/B8 BSS
G2 BTS release B7.2 functions are unchanged.
The following table lists the maximum and minimum capacity for G2 BTS..
Extension / ReductionConfiguration
Physical Logical
BTS Minimum Maximum Minimum
G2 1 TRE 1 Sector:8 TRE 1 TRE 1 TRE
Table 12: G2 BTS
3.4 G1 BTSOnly MKII G1 BTS with DRFU and DRFE are supported in release B9, andrelease B7.2 functions are unchanged.G1 BTS are allowed to have channel combinations other than TCH.G1 BTS can support GPRS, unless they belong to the inner zone.
3.5 BTS SynchronizationIn terms of dimensioning, from a software point of view, there can but up to3 BTS slaves.Depending on the hardware configuration, the number of BTS slaves canbe reduced to 2 or 1 BTS.The following table lists the type of slave BTS which can be synchronized to themaster and the number of BTS slaves, for each BTS master.
Master Slaves Hardware Limitation Software Limitation
G2 standard G2 5 3
G2 standard Evolium 5 3
50 / 162 3BK 17422 5000 PGZZA Ed.06b
-
3 BTS Configurations
Master Slaves Hardware Limitation Software Limitation
G2 mini G2 2 3
G2 mini Evolium 2 3
Evolium medi/mini G2 1 3
Evolium medi/mini Evolium 3 BTS slaves maximumin a chain configuration
3
Table 13: BTS Synchronization
3.6 Physical Channel Types
3.6.1 GSMIn terms of TS content, there are several possible configurations, the mostrelevant of which are:
Traffic channels (TCH)Signaling channels:
BCC = FCCH + SCH + BCCH + CCCHCBC = FCCH + SCH + BCCH + CCCH + SDCCH/4 + SACCH/4SDC = SDCCH/8 + SACCH/8.
Note: Two CBCH channels can be defined for cells used for SMS-CB:
The basic CBCH channel
The extended CBCH channel.
If the basic CBCH channel is configured, the extended CBCH channel can beoptionally configured. The extended CBCH channel is managed in the samemanner as the basic CBCH channel (2 instances of scheduling per cell).When the initial SDCCH number in a cell is small, a reduction in the numberof SDCCH due to the configuration of the CBCH can increase the SDCCHaverage load. In such a case, the operator may need to add one SDCCH TS.
3.6.2 GPRSWhen the TRX_PREF_MARK parameter is set to 0, GPRS service is available.If it is set to 1, GPRS is not supported in the cell.GPRS radio time-slots (PDCH) are dynamically allocated according to thefollowing, customer-defined parameters:
MIN_PDCH defines the minimum number of PDCH TS per cell
MAX_PDCH defines the maximum number of PDCH TS per cell
MAX_PDCH_HIGH_LOAD defines the maximum number of PDCH TS per cellin the case of CS traffic overload.
3BK 17422 5000 PGZZA Ed.06b 51 / 162
-
3 BTS Configurations
Those parameters allow the operator to prioritize CS traffic versus GPRS trafficin order, for example, to avoid a QoS drop while introducing GPRS.The following quality parameters can also be used:
N_TBF_PER_SPDCH defines the number of MS that can share the same PDCH
The number of Temporary Block Flow (TBF) allocated on one or morePDCHs.
3.7 Frequency Band Configuration
3.7.1 OverviewE-GSM is used for the whole GSM-900 frequency band, i.e. the primary band(890-915 MHz / 935-960MHz) plus the extension band (880-890 MHz/925-935MHz), this corresponds to 174 addressable carrier frequencies and leads to anincrease of 40 % against the 124 frequencies in the primary band.
Frequency span (U)ARFCNs Uplink frequencies Downlink frequencies
P-GSM band 1.. 124 890.2 to 915.0 MHz 935.2 to 960.0 MHz
G1 band 975.. 1023, 0 880.2 to 890.0 MHz 925.2 to 935.0 MHz
GSM850 band 128... 251 824.2 MHz to 848.8 MHz 869.2 MHz to 893.8 MHz
DCS1800 band 512.. 885 1710.2 to 1784.8 MHz 1805.2 to 1879.8 MHz
DCS1900 band 512.. 810 1850.2 to 1909.8 MHz 1930.2 to 1989.8 MHz
3.7.2 CompatibilityThe following table shows BTS generation equipment versus radio band.
Multiband (BTS or Cell)Yes = a GSM 850 GSM 900 GSM
1800GSM1900
850/1800 850/1900 900/1800 900/1900
G3/G4BTS
a
(*)E-GSM a a a a a a
M5MBTS
a E-GSM a a a a a a
M4MBTS
N.A a a N.A N.A N.A a N.A
G2 BTS N.A E-GSM a a N.A N.A N.A N.A
G1 MKIIBTS
N.A a N.A N.A N.A N.A N.A N.A
52 / 162 3BK 17422 5000 PGZZA Ed.06b
-
3 BTS Configurations
* : The BTS can be a G3 BTS, but the TRE is a G4.2 TRE.Table 14: Frequency band configuration
3.7.3 RulesFrom functional point of view, two types for the multiband behavior:Multiband BTS: The frequency bands (850/1800, or 850/1900, or 900/1800) areused in different sectors of the BTS. There are 2 BCCH carriers, one in thesector with frequency band 1, one in sector with frequency band 2.Multiband cell: The sector (cell) is configured with TRX in band 1, and TRX inband 2. Only one BCCH carrier is configured for the sector.
3.8 Speech Call Traffic RatesThere are no compatibility limitations between BTS and TC generations.The following table shows the hardware transmission compatibility.
Yes =a A9125 TC ( MT120) G2 TC(DT16/MT120)Evolium, M4M, M5M a a
G2 + DRFU a a
G1 MKII + DRFU a a
Table 15: Hardware Transmission Compatibility
The following table shows the different rates available over different generationsof equipment.
BTS Traffic Rate
Evolium, M4M, M5M
G2 + DRFU
G1 MKII + DRFU
FR,DR,EFR,AMR
Table 16: Speech Call Traffic Rates
Dua