growspan series 500 door kits - farmtek › wcsstore › engineering... · 100380 mounting bracket...
TRANSCRIPT
1Revision date: 04.30.19
STK# GS05KDR1SLT (Twin-Wall Polycarbonate)GS05KDR1SLC (Corrugated Polycarbonate)
Diagram shows a sliding door centered and installed in an end wall frame. The door kit includes materials for the door only. All other components shown in the diagram above and other diagrams throughout this guide are not included and require additional purchase.
Finished Grade
Single Sliding Door
©2019 GrowSpanAll Rights Reserved. Reproduction is prohibited without permission.
GrowSpan™ Series 500Door Kits
22 Revision date: 04.30.19
Table of ContentsSINGLE SLIDING DOOR KIT: READ BEFORE YOU BEGIN
The single sliding door kit is designed to attach to any of these end frame kits: GS05KEW20G72, GS05KEW24G72, GS05KEW30G72 and GS05KEW35G72. These instructions and the instructions for the end frame are written to be used together.
Install the end wall framing before you install the door frame. Consider the positions of fans, vents, and other accessories before you install the door frame.
Door must not block or interfere with the operation of building accessories.
If you are installing this door kit in an end frame that is not identified above, use these instructions for critical dimensions and details.
Consult the services of a qualified contractor if needed. It is the responsibility of the owner/contractor to adapt these instructions to safely and competently install this door in an end frame or building that it was not designed for.
Complete these steps to begin and to install the door:
1. Based on the dimensions of the door (or doors), determine where you can position the door in the end frame. Use the diagrams from both this manual and the end wall assembly guide.
2. Secure the door framing to the end wall framing.
3. Assemble 102923 door frame and door and attach assembled door to end wall. NOTE: If you purchased a fabric end panel to cover the end, install the panel before you install the door; then remove the panel material as needed to allow for the installation of the door. If you purchased a poly carbonate end wall package (8 mm twin-wall or corrugated), install those panels after installing door frame and before installing the door. IMPORTANT: Consult the stay roller installation steps before installing end wall polycarbonate panels.
Important Information ..............................................3Bearing Hangers .......................................................5Door Frame Assembly .............................................6Stay Roller Assembly ...............................................7Sliding Door Track Assembly ..................................8Adjust Doors .............................................................11Twin-Wall Single Sliding Door Assembly ...............12Corrugated Single Sliding Door Assembly ............14Shelter Care and Maintenance ................................16Quick Start Guide .....................................................17Door Frame Layout ...................................................18Door Frame Detail Connections ..............................19
33Revision date: 04.30.19
Important Information
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT.
Thank you for purchasing this GrowSpan™ door kit. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the door. Please read these instructions before you begin.
SAFETY PRECAUTIONS
• Wear eye protection.
• Wear head protection.
• Use a portable GFCI (Ground Fault Circuit Interrupter) when working with power tools and cords.
• Do not climb on the framing during or after construction.
• Provide proper ingress and egress to prevent entrapment. WARNING: The individuals assembling this door are responsible for designing and furnishing all temporary bracing, shoring and support needed during the assembly process. For safety reasons, those who are not familiar with recognized construction methods and techniques must seek the help of a qualified contractor.
FASTENERS
Fasteners are included to secure door components to metal frame members. If the building frame and cladding are not metal, purchase the appropriate fasteners locally, or call customer service for suggestions.
REQUIRED TOOLS
The following list identifies the main tools needed to assemble the door. Additional tools and supports may be needed depending on the structure, location, and application.
• Tape measure or measuring device
• Fine point marker to mark the location frame members.
• Variable speed drill (cordless with extra batteries works the best)
• Drill bit set with 7/16" and 1/2" drill
• Wrench set
• Hammers, gloves, and eye protection
• Ladders, work platforms, and other machinery for lifting designed to work safely at the height of the door and door frame.
ATTENTION: Consult the services of a qualified, professional contractor if you are not familiar with the construction of similar frame structures and components.
44 Revision date: 04.30.19
Important Information
PARTS IDENTIFICATION
The following graphics and photos will help identify the different hardware for each door kit. (Some parts are not shown.)
102921B & FA4484BTek Screws and neo-bonded washers
104213Aluminum U-Channel Profile(Twin-Wall Only)
104548End cap profile
100380Mounting bracket
ASSEMBLY PROCEDURE
Following the instructions as presented will help ensure the proper installation of the end frame and door. The steps outlining the assembly process are as follows:
1. Verify that all parts are included in the shipment. Notify Customer Service for questions or concerns.
2. Read these instructions and all additional documentation included with the shipment before you begin.
3. Gather the tools, bracing, ladders (and lifts), and assistance needed to install the door and door frame.
4. Read the care and maintenance information at the end of these instructions.
5. Complete and return all warranty information as instructed (if included).
UNPACK AND IDENTIFY PARTS
The following steps will ensure that you have all the necessary parts before you begin.
1. Unpack the contents of the shipment and place where you can easily inventory the parts. Refer to the Bill of Materials/Spec Sheets.
2. Verify that all parts listed on the Bill of Materials/Spec Sheets are present. If anything is missing or you have questions, consult the parts guide and all diagrams for clarification, or contact customer service. NOTE: At this time, you do not need to open the plastic bags containing smaller parts such as fasteners and clamps (if equipped).
QUICK START DIAGRAMS
For a quick overview of the end wall, door, and components, consult the diagrams located at the back of these instructions.
104709Horizontal closure strip
(Corrugated Only)
116391Bearing Hanger
100356Stay roller
55Revision date: 04.30.19
Bearing HangersASSEMBLE AND INSTALL SLIDING DOORS — OVERVIEW
The general steps to install the sliding door are as follows:
1. Assemble the 102923 door frame.
2. Attach bearing hangers to the door frame.
3. Construct the rough opening in end wall frame.
4. Attach stay roller and the sliding door track to the end wall.
5. Hang the sliding door in the door track and adjust sliding door as needed.
6. Attach polycarbonate panel to door frame.
7. Install 115581 screws through track to prevent door(s) from sliding out of the track.
8. Attach door handle and reinstall door (if removed to install cladding).
ATTACH ROLLER ASSEMBLIES TO DOOR FRAME
Complete the following steps to attach bearing hangers to the door frame.
1. Assemble 102923 door frame.
2. Locate and unpack the 116391 bearing hangers. The door requires two bearing hangers.
3. Insert mounting bolt through top of roller bearing and add one adjusting locknut.
4. Insert end of mounting bolt through mounting hole in top of door frame and add the remaining adjusting locknut. NOTE: Use 1/2" drill bit and drill to enlarge hole if bearing hanger bolt does not fit.
5. Continue with next procedure.
Door Frame Tube
Adjusting Locknut
Adjusting Locknut
Mounting Adjusting Bolt
Bearing Hanger
ATTENTION: Use 1/2" drill bit and drill to enlarge hole if bearing hanger bolt does not fit.
66 Revision date: 04.30.19
Door Frame Assembly
S15P118 Header (cut to length)
90"
45"
Concrete Concrete
Finished Grade
(inside-to-inside)
Bottom of header to top of finished grade.
Door jamb anchored in concrete.
FinishedGrade
*Not shown to scale.
NOTE: End frame and rafter are not included with any door kit.
Tek screws
QH1330
ASSEMBLING THE DOOR FRAME COMPONENTS
Consult the diagrams at the back of these instructions before you begin. Assistance is required to assemble the door frame and door. The following steps describe one way to assemble the door frame and door.
1. Using the dimensions on the Door Frame Layout diagram (Quick Start Section), determine the positions of the doorjambs.
2. Dig 8"-10" diameter holes at the locations found in previous step to a depth that is below the geographic frost line. Minimum depth: 24".
3. Using the rough door opening dimensions and the door frame components, assemble and install the door frame. See diagram below.
4. Square door frame and secure doorjambs in holes using concrete. Verify door frame dimensions before you secure jambs in concrete. Doorjambs must be plumb for proper door operation.
5. Once door frame is attached to end wall framing, assemble the door. Consult the procedures on the next few pages for your door (twin wall or corrugated polycarbonate).
77Revision date: 04.30.19
Finished GradeFinished Grade
Position the stay roller at this corner when the door slides open in this direction.
Dashed line shows the approximate position of the sliding door track.
Stay Roller AssemblyASSEMBLE AND ATTACH STAY ROLLERS
1. Locate the 100356 stay roller and remove the roller, bushings, bolt, and nuts.
2. Secure the angle bracket in the lower-right corner of the assembled door frame as shown below. Allow clearance under bracket to attach stay roller.
Reattach the stay roller and related parts to the angled bracket attached to the end wall frame.
NOTE: Do not tighten the stay roller at this time. It is adjusted and tightened when the door is installed.
ATTENTION: Stay roller assembly is attached to the door jamb on the same side the door is on when in the open position. For illustration purposes, the following diagrams show the stay roller attached to the right side.
ATTENTION: After installing the stay roller, install the end wall cladding (polycarbonate panels or fabric panel). The polycarbonate panels of any end wall PC package must be installed before you install the sliding door assembly. Complete the installation of all polycarbonate panels at this time for these kits: GS05KCC2072 and GS05KCT2072, GS05KCC2472 and GS05KCT2472, GS05KCC3072 and GS05KCT3072, and GS05KCC3572 and GS05KCT3572.
NOTE: Secure using 115581 pancake head screws if screws are not included with roller. Do not use the holes marked with an X in the diagram.
Doo
rjam
b
DoorOpening
Outside of Building
Doo
rjam
b
Finished Grade
Assemble with the two brass bushing on the underside of the roller.
X
X
Door Opening
Finished Grade
88 Revision date: 04.30.19
Sliding Door Track AssemblyATTACH DOOR TRACK Gather the parts:
• FAK26 3/8" threaded rod, FALB04B 3/8" nuts, FAME18B 3/8" SS flat washers, FAMA38B lock washers, and FAME52B 3/8" flat washers
• FA4484B Tek screws and 102921B neo-bonded washers
• 100377 door track and 100380 hanger bracket for door track
Complete these steps to install the slider door track (100377). Complete only those steps that apply to the type of end wall polycarbonate (8mm twin-wall or corrugated) that covers the end frame.
1. Review diagram below for the slider track position. Track typically extends 1"-2" past the outer edge of the doorjamb. Space the three (3) track hanger brackets (100380) evenly along the slider track. ATTENTION: Install hangers in a position so the mounted track is above the top of the door header. Add another end wall horizontal tube if needed to correctly mount the slider track. Door opening is smaller than the actual sliding door frame to prevent door from pushing into the opening. The position of the sliding door frame when installed and closed will align with the header and doorjambs of the end wall door frame.
Position of slider track above door opening.
Edge of Doorjamb
100380 Bracket
STEP 1
Door slides this way to open.
slider track
Header
Doo
rjam
b
Doo
rjam
b
Finished Grade
STEP 1: Dashed lines identify the outer edge of each doorjamb. Sliding door is closed.
99Revision date: 04.30.19
Twin-Wall Polycarbonate End Wall Panel
Outside Building
FAME18B Flat WasherEnd Wall
Frame Tube
Inside Building
FALB04B Nut
FAME18B Flat Washer
FAMA38B Lock Washer
FAK26 Rod
FALB04B Nut
Sliding Door Track Assembly
2. Mark bracket positions on end wall cladding. Space brackets evenly along the length of slider track. For corrugated panels, drill 7/16" mounting holes in the valleys of the panels. Shift brackets left or right as needed. Drill one 7/16" hole through the end wall cladding and steel tube framing for each bracket. Drill holes level and straight through the tube to mount the brackets and track properly. See diagrams below and on the next page. For twin-wall polycarbonate panels, first drill a 1" hole through the twin-wall panel only at bracket mount position, then drill the 7/16" mounting hole through the end wall frame tube. This allows the mounting nuts and washers to directly contact end wall frame without crushing the twin-wall polycarbonate panels. See diagrams below and on the next page. Before you install track bracket, fill hole in polycarbonate panel using customer-supplied sealant.
ATTACH DOOR TRACK (continued)
3. Install the FAK26 rod as shown above.
4. Repeat to install and secure the remaining FAK26 threaded 3/8" rods.
Corrugated Polycarbonate End Wall Panel
Outside Building
FAME18B Flat Washer
End Wall Frame Tube
Inside Building
FALB04B Nut
FAME18B Flat Washer
FAMA38B Lock Washer
FAK26 Rod
FALB04B Nut
NOTE: Fill hole in panel with customer-supplied silicone sealant after nut is tightened.
SIDE VIEW
SIDE VIEW
1010 Revision date: 04.30.19
Sliding Door Track Assembly
5. Install the mounting brackets and door track. See diagrams below. NOTE: For polycarbonte panels, install as many FAME52B washers as needed to prevent the track bracket from touching the panel when installed, then secure with the nut, lock washer and flat washer. See diagrams below.
6. Position track as needed in the brackets to allow door to fully close and open when operated. See diagrams below.
ATTACH DOOR TRACK (continued)
7. Add FAME18B flat washer, FAMA38B lock washer, and FALB04B nut to each threaded rod. Tighten the nuts to secure mounting brackets to the frame. Cut the threaded rods to the desired length.
8. Continue with next procedure.
TOP VIEW SHOWING TRACK BRACKET
Track bracket with track installed.
Track bracket with track installed.
FAME52B Flat Washers
FAME52B Flat Washers
100380 Bracket
100380 Bracket
1111Revision date: 04.30.19
Adjust Doors
Adjusting Locknut
Adjusting Locknut
INSTALL AND ADJUST SLIDING DOOR
Complete these steps:
1. With assistance, carefully lift door into position and slide bearing hangers into the end of the door track.
2. Slide door to its closed position.
3. Adjust the nuts on each bearing hanger to achieve the desired fit.
ATTENTION: Door will hang level and square with door frame in end wall when properly adjusted. Door should glide freely through the stay roller. Adjust as needed.
4. Tighten nuts to secure bearing hanger adjustment.
5. Loosen the stay roller as needed to adjust later.
NOTE: Allow clearance for door cladding, which is installed later. Actual positions of components may differ from diagram.
6. Continue with the next procedure.
Space below is reserved for customer notes.
Door Jamb
End Frame Base Tube
Inside Building
Outside Building
Slid
ing
Doo
r Fra
me
Ground LevelAdjust and Tighten
Door panel installed later.
1212 Revision date: 04.30.19
Twin-Wall Single Sliding Door AssemblyTWIN-WALL DOOR ASSEMBLY
If your door kit includes a corrugated polycarbonate panel, skip this section and continue with the assembly steps for that door. The materials and parts needed to assemble the door include:
• Assembled door frame with bearing hangers
• 8 mm panel (116049)
• Door handle (100362)
• Pancake head screws (115581)
• Neo-bonded washers (102921B)
• Aluminum profile (104213)
Assemble and Attach Door
NOTE: Attach polycarbonate panel with UV-protected side toward the outside/sun.
1. Remove door frame with bearing hangers from door track and place on a flat surface.
2. Take polycarbonate panel and trim so length is one-quarter inch (1/4") shorter than length of door frame.
NOTE: Attach panel in locations shown in photo to hold in place while attaching aluminum profile to perimeter of panel.
6. Install aluminum U-channel profile to all edges of polycarbonate panel. The 104213 sections at top and bottom of panel run to panel edges to seal cells.
5. Using 115581 pancake head screws and galvanized neo-bonded washers, attach panel to horizontal cross tube of door frame. Evenly space screws and washers every 12".
3. Trim width of panel (if needed) so that it is one-quarter inch (1/4") narrower than width of door frame. NOTE: Trimming panels as instructed will keep panel flush with edges of the door frame once the aluminum profile (104213) is installed.
4. Center panel on door frame.
Mark UV Side X
Install this edge to the underside of the panel against the door frame.
Photo shows the polycarbonate panel attached to the outside of the door frame and finished with the aluminum (104213) U-channel profile.
45° Angle
1313Revision date: 04.30.19
Twin-Wall Single Sliding Door Assembly
TWIN-WALL DOOR ASSEMBLY (continued)
7. Take the 115581 screws and, using the 100448 bit and drill driver, secure trim to door. Carefully install each screw. DO NOT OVERTIGHTEN! Doing so will dent the aluminum trim pieces.
10. After adjustments are made, slide door to its open position and install two Tek screws through the front of the door track at both ends to prevent the door from sliding out of the track.
11. Install the door handle in the desired location, using 115581 pancake head screws through the panel and into the door frame. Handles can be installed vertically or horizontally.
12. Install the 104548 profile along the end wall door frame as shown in the following photos.
ATTENTION: The installation of the 104548 profile is an optional step for those who want to cap the end of the end panels at the door opening. Use Tek screws to secure the profile to the end wall framing. View is from the inside of the frame looking at the point where the door meets the door frame of the end wall.
13. Check the door operation and verify that door slides smoothly in the door track. Adjust as needed.
14. Continue by reading the care and maintenance information.
Stay Roller
SIDE VIEW
Adjust Stay Roller as needed.
Door w/Panel Attached
Door Frame w/Panel Attached
Door Door Frame
Step 10
Door Handle
115581 Screws
ATTENTION: Do not use an impact driver to install screws. Use a variable speed drill and the 100448 nut setter. Install screws at 16" on-center.
8. With assistants, lift door up and into place with the panel facing out and insert the rollers into the track.
9. Slide door to the closed position and adjust the stay roller at bottom corner as needed and tighten.
Stay Roller
Door w/Panel Attached
Door Opening
Slide to
Close
1414 Revision date: 04.30.19
CORRUGATED DOOR ASSEMBLY
The materials and parts needed to assemble the door include:
• Door frame (102923) and corrugated panel (104620)
• Tek screws (FA4484B)
• Neo-bonded washers (102921B)
• Horizontal closure strip (104709)
Attach Panel to Door Frame
1. Take door frame with attached bearing hangers and place it on a flat surface.
2. Select one (1) corrugated panel—this will be one 50" x 8' 2" panel—and trim it so that the length is one-quarter inch (1/4") shorter than the length of the door frame. Pay attention of where the valleys of the panel end.
3. Install sections of the horizontal closure strips under the panel (see Detail A) and before attaching the panel to the horizontal cross tube. Trim one (1) closure strip as needed for each of the three (3) locations.
4. Install Tek screws and washers through the panel, closure strip, and into the horizontal cross tube every 6" or so. Always install Tek screws and washers in the valleys of the panel. Do not overtighten screws.
5. Attach the panel in the locations shown below to hold the panel in place.
6. Secure the sides of the polycarbonate panel to the door frame using Tek screws only every 16" (see Detail B).
Corrugated Panel
Valley
NOTE: Verify that the horizontal closure strip under the panel is in place before attaching the panel to the door frame.
Corrugated Single Sliding Door Assembly
DDEETTAAIILL AA
4488""
9922""DDEETTAAIILL AA
DDEETTAAIILL BB
DDEETTAAIILL BB
Closure Strip
Step 3
Closure Strip
Closure Strip
Closure Strip Tek Screw and Washer
ValleyDashed lines identify the positions of the foam closure strip (104709).
1515Revision date: 04.30.19
Corrugated Single Sliding Door Assembly
CORRUGATED DOOR ASSEMBLY (continued)7. With assistants, lift door up and into place with the
panel facing out and insert the hangers into the track.
8. Slide door to the closed position and adjust the stay roller as needed and tighten.
9. After adjustments are made, slide door to its open position and install two Tek screws through the front of the door track at both ends to prevent the door from sliding out of the track.
11. Install the 104548 profile along the end wall door frame as shown in the following photos. ATTENTION: Installation of the 104548 profile is an optional step for those who want to cap the end of the corrugated end panels at the door opening. Use Tek screws to secure the profile to the end wall framing.
Photo above shows end wall without installed profile. Dashed line shows where to install profile to cover the valleys of corrugated end panels. View is from the inside of the frame looking at the point where the door meets the door frame of the end wall. See diagram below for top view. See page 13 for installed view.
Stay Roller
SIDE VIEW
Adjust Stay Roller as needed.
Door w/Panel Attached
Door Frame w/Panel Attached
Door
Door Frame
NOTE: Photo shows panels running horizontally. Actual frame will have vertically running panels. Photo is for illustration purposes.
Step 9
Door Handle
10. Install the door handle in the desired location, using Tek screws through the panel and into the door frame.
12. Check the door operation and verify that door slides smoothly in the door track. Adjust as needed.
13. Continue by reading the care and maintenance information.
Stay Roller
Door w/Panel Attached
Door Jamb w/ End Panel Attached
Door Opening
Slide to
Close
Outside Inside
104548 Aluminum Profile
TOP VIEWSlide Door to Open
Doo
r Fra
me
Door Jamb
End Wall Horizontal Support
Cor
ruga
ted
Pane
l
Corrugated Panel – End Wall
1616 Revision date: 04.30.19
Space below is reserved for customer notes.
Shelter Care and MaintenanceSHELTER CARE AND MAINTENANCE
Proper care and maintenance of the door are important. Check the following items periodically to properly maintain the door and door frame:
• Regularly check polycarbonate panels to see that they remain secure and in good condition. Replace damaged panel if needed.
• Check connections and all fasteners to verify that they remain tight.
• Check shelter contents to verify that nothing is touching the polycarbonate panels that could cause damage or interfere with the door operation.
• For safety, door must remain fully opened or fully closed. Do not leave door ajar.
• Check all slider mounting bolts regularly and tighten as needed.
• Replace damaged or broken parts immediately.
• Lubricate bearing hangers and stay rollers as needed to keep them operating smoothly.
• For replacement or missing parts, contact you sales representative for assistance.
1717Revision date: 04.30.19
QUICK START GUIDE
Single Sliding Door Kit (GS05KDR1SLT and GS05KDR1SLC)
Quick Start Guide
Corrugated Door SampleGS05KDR1SLC
Ground Level
Twin-Wall Door SampleGS05KDR1SLT
Ground Level
ATTENTION: End frame and end rafter are not included with any door kit. Actual width of the building end wall may differ.
18 Revision date: 04.30.19
Doo
r Fr
ame
Layo
ut
2'-0
"E
MB
ED
ME
NT
90"
R.O
.
VIEW
1H
EA
DE
R T
O E
ND
WA
LL C
OLU
MN
CO
NN
EC
TIO
N
(S15
P020
)(C
UT
TO F
IT IF
NE
ED
ED
)1.
5" X
1.5
" SQ
UA
RE
TU
BE
1.5"
X 1
.5" S
QU
AR
E T
UB
E (S
15P1
18)
(CU
T TO
FIT
IF N
EE
DE
D)
1.5"
X 1
.5" S
QU
AR
E T
UB
E (S
15P0
20)
(CU
T TO
FIT
IF N
EE
DE
D)
)
(QH
1330
)
DO
OR
JA
MB
TO
HE
AD
ER
CO
NN
EC
TIO
NVI
EW 3
1.5"
X 1
.5" S
QU
AR
E T
UB
E (1
0289
710
2897
)
GR
OU
ND
LE
VE
L
AN
GLE
BR
AC
KE
T (Q
H13
30)
AN
GLE
BR
AC
KE
T (Q
H13
30)
AN
GLE
BR
AC
KE
T
(QH
1330
)
1.5"
X 1
.5" S
QU
AR
E T
UB
E (
AN
GLE
BR
AC
KE
T
VIEW
21.
5" X
1.5
" SQ
UA
RE
TU
BE
CO
NN
EC
TIO
N
45"
R.O
.
ATTE
NTI
ON
: Squ
are
the
door
ope
ning
an
d m
easu
re th
e do
or b
efor
e an
chor
ing
the
door
jam
bs in
con
cret
e.
19Revision date: 04.30.19
Doo
r Fr
ame
Det
ail C
onne
ctio
ns
DO
OR
HE
AD
ER
DO
OR
JA
MB
A
NG
LE B
RA
CK
ET
(QH
1330
)- (
4X) #
14 X
1" T
EK
SC
RE
W
VIEW
21.
5" X
1.5
" SQ
UA
RE
TU
BE
CO
NN
EC
TIO
NH
EA
DE
R T
O E
ND
WA
LL C
OLU
MN
CO
NN
EC
TIO
NVI
EW 1
VIEW
3D
OO
R J
AM
B T
O H
EA
DE
R C
ON
NE
CTI
ON
1.5"
X 1
.5" S
QU
AR
E T
UB
E
- (2X
) #14
X 1
" TE
K S
CR
EW
EN
DW
ALL
CO
LUM
N
DO
OR
HE
AD
ER
A
NG
LE B
RA
CK
ET
(QH
1330
)- (
4X) #
14 X
1" T
EK
SC
RE
W
ATTE
NTI
ON
: Ins
tall
scre
ws
in a
loca
tion
that
w
ill no
t int
erfe
re w
ith th
e in
stal
latio
n of
the
door
as
sem
bly.