R/C Car

Long Nose Pliers

Nippers

Soft Brush Hex Driver

Screwdrive(Small)

Screwdrive(Large)

BatteryCharger Hex Wrench 4 x AA Batteries Wrench

Transmitter

WHAT’S IN THE BOX TOOLS RECOMMENED(NOT INCLUDED)

7.2V 1200mAh NiMHRechargeableBattery Pack

DIMENSIONSCALE : 1/16HEIGHT : 170mmTYRE : ø79mm x 43mm(width)LENGTH : 336mmWIDTH : 239mmWHEELBASE : 189mm

Visit Us on www.carisma.com.hk

Printed in China MAN-G00486

©2013 Carisma. All Rights Reserved. Product specifications are subject to change. Some models shown are prototypes which may vary slightly from what is inside.

2

SAFETY PRECAUTIONS

11

SAFETY PRECAUTIONSTHIS MODEL IS ONLY SUITABLE FOR PEOPLE 14 YEARS OLD AND UP. THIS RADIO CONTROL MODEL IS NOT A TOY.

Introduction

Safety, Precautions, and Warnings

Beginner should seek advice from experienced person in order to assemble the model or parts correctly and to make best performance. * Assemble this model or parts only in place out of children’s reach, and take safe precautions before operating this model. User is fully responsible for the model assembly and safe operations.

This is a sophisticated hobby product and not a toy. It must be operated with caution and common sense. User also requires some basic mechanical abilities. Fail to operate this product in a safe and responsible manner could result in injury or do damage to the product or other properties. This product is not intended for use by children without direct adult supervision. The product manual contains instructions for safe operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual prior to assembly, setup or use, in order to operate correctly and avoid damage or injury.

As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself and others or result in damage to the product or the property of others.This model is controlled by a radio signal that is subject to interference from many sources outside your control. This interference can cause momentary loss of control so it is necessary to always keep a safe distance in all directions around your model, as this will help to avoid collisions or injury.• Always operate your model in an open area away from cars, traffic, or people.• Avoid operating your model on the street where injury or damage can occur.• Never operate the model out into the street or populated areas for any reason.• Never operate your model with low transmitter batteries.• Carefully follow the directions and warnings for this product and any optional support equipments (chargers, rechargeable battery packs, etc.) that you use.• Keep all chemicals, small parts and anything electrical out of the reach of children.• Moisture causes damage to electronics. Avoid water exposure to all equipments not specifically designed and protected for this purpose.

The associated regulatory agencies of the following countries recognize the noted certifications for this product as authorized for sale and use.

UK

FI

CZ

AT

NL FRDE

EE

SK

IT LU

DK

LV

HUES

MT

BG

LT

RO PT

CY

SE

PL SI IEGR

CE Compliance Information For The European Union

Declaration of Conformity Products: Carisma CTX-2710 2.4GHz Transmitter, MRX2800 ReceiverEquipment Class: 2 The objects of declaration described above are in conformity with the requirements of the specifications listed below.

Manufactured By : Mun Ah Plastic Electronic Toys Company.,Ltd

Statement - This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC ID YDTMTM27HP

Item Name : Carisma CTX-2710 2.4GHz Transmitter and MRX2800 Receiver ETSI EN 300 328 V1.7.1:2006ETSI EN 301 489-1 V1.8.1:2008EN 301 489-17 V2.1.1:2009 EN 50371:2002Directive 1999/5/EC (R&TTE) Article 3.1a Health Article 3.1b EMC Article 3.2 Radio Spectrum

RF Exposure Warning:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.And should be operated with minimum distance of 20 cm between the antenna & your body.

EXPLODED DIAGRAM

Item Name : V6 Type R Electronic Speed ControllerEN 301 489-3 V1.4.1 EN 301 489-1 V1.8.1

Item Name : MS-903GT ServoEN 55 014-1:2006EN 55 014-2:1997 + A1:2001

3

ABOUT THE RADIO SYSTEM

ST.TRIM

TH.TRIM

CTX-2710

Battery Compartment Tray

Steering Trim Dial

Dual Rate Dial

* In general, user will experience under steer when making a wide turn at high speed or over steer when making sharp turn at high speed (easy to spin out). User should practice the throttle and steering approach for different cornering at different speed or road surface.

Battery Installation

SYNC

The following is an overview of the various functions and adjustments found on CTX-2710 radio system for Carisma models. It is important to read and understand about all of these functions and adjustments before driving.

Carisma CTX-2710 2.4GHz FHSS Technology System

Functions

ST.TRIM

TH.TRIM

The Transmitter CTX-2710 Steering Wheel : Control direction (Left / Right) of the RC model. Throttle Trigger : Control speed and direction (Forward/Brake/Backward) of the driving model. Antenna : Transmit signal to the model. Power ON / OFF : Power ON / OFF the transmitter SYNC & Battery Indicator : Top Green LED light indicates synchronization status and/or adequate battery power supply. Power Indicator : Bottom Red LED light indicates power “ON”. Dual Rate Dial : Adjust the same maximum steering angle on both sides when model turns Left / Right ST. Trim Dial : Adjust the neutral position of steering servo when model wheels are straight ahead. TH. Trim Dial : Make sure the model stays still when releasing the throttle trigger. Battery Compartment Tray : Cover and hold the batteries powering the transmitter.

Supplied with 4 x 1.5V AA Batteries, CTX-2710 can be operated a few hours. Installation: Remove the battery compartment cover as shown below.

Install the batteries observing the polarity marked on battery compartment.

Then reinstall the battery compartment cover as the Picture shown below.

Warning : Never disassemble batteries or put the batteries in fire, chemical agents, otherwise they may cause personal injuries or property damages.Battery Disposal : Observe corresponding regulations about wasted battery treatment regulations. 1. After running out of power, dispose of wasted batteries in designated areas far away from water supply, household areas and planted areas.2. Submit the wasted batteries to specific recycling stations.

Battery LED IndicatorThe Green LED indicator located on the front left side of the transmitter indicates the power supply of batteries. The green LED will go solid on indicating that the batteries have sufficient power. When batteries voltage drops below 4 volts, the Green LED will flash, indicating the batteries power is low and should be replaced.

Pre-Run Check

Solid Green : Sufficient Power supply

Flashing : Time to replace batteries

Steering Wheel

Throttle Trigger

Throttle Trim Dial

Antenna

SYNC andBattery

Level Indicator

Power Indicator

PowerON / OFF

Green

Red

SYNC

SYNC Button(Synchronization)

* Always turn on the transmitter first by sliding the switch on the left side from bottom to top. The small red and green lights above the switch should both light up. If not, you need to check for low or incorrectly installed batteries.

1. Steering : Adjust the steering trim to keep the front wheels in straight line when steering wheel remains in NEUTRAL position.

2. Throttle : Adjust the throttle trim to ensure the rear wheels stop rotating when throttle trigger remains in NEUTRAL position.

For Transmitter

Damages or LeakingDo not use any damagedbatteries.

x 4

This product must never be thrown away with other waste. Thus the users are liable for disposingthe wasted model by submitting them to designated collection stations specific for recycling electronic and electric items. Disposing of the wasted model in this way is helpful to conserve natural resources and enable to keep human health and protect the environment. For more information about wasted model disposal and recycling, please contact your local city office, your disposal service or where you purchased the product.

Instructions for Disposal of WEEE by Users in the European Union

Heavy Duty1.5V “AA” Size Batteries

ATTENTION

10

ITEM NO BARCODE PRODUCT NAME PART NO QTYDESCRIPTION

SPARE PARTS LIST

MASM053AMASM1684AMASM1685A

E-RINGFRONT OIL SHOCK SHAFTREAR OIL SHOCK SHAFT

822

SHOCK SHAFT SET489279314805414805

15138 4892793151382 GT16MB VOLKWAGEN BEETLE DESERT EDITON WHEELS & TYRES SET (WHITE) MAT-016-TA-00017BR WHEELS & TYRES SET 2

MAT-016-SA-00017MAT-016-SA-00018

FRONT OIL SHOCK ASSEMBLEDREAR OIL SHOCK ASSEMBLED

22GT14 / 16B / 16MB PLASTIC OIL SHOCK SET489279314922814922

16MBP0302GT14BP0601-01GT14BP0604GT14BP0605

FRONT HING PINFRONT HING PIN BRACEREAR INNER HINGE PIN BRACEREAR OUTER HINGE PIN BRACE

1111

GT16 MONSTER BEETLE HING PIN BRACE SET489279314929714929

14924 4892793149242 GT16 MONSTER BEETLE 370 MOTOR MOUNT 116MBP0401 370 MOTOR MOUNT14926 4892793149266 GT16 MONSTER BEETLE FRONT SHOCK TOWER FRP-G00062 FRONT SHOCK TOWER 1

14928 4892793149280 GT16 MONSTER BEETLE MAIN CHASSIS 1FRP-G00064 MAIN CHASSIS

15140 4892793151405 GT16MB VOLKWAGEN BEETLE DESERT EDITON STICKER SHEET 1DCC-G00289 STICKER SHEET

14927 4892793149273 GT16 MONSTER BEETLE REAR SHOCK TOWER FRP-G00063 REAR SHOCK TOWER 1

112

GT16MBB0101GT16MBB0102MASM1366A

TOP DUST COVERBOTTOM DUST COVERSNAP PIN

GT16 MONSTER BEETLE DUST COVER SET489279314930314930

41212

MASM2158AMASM2156AMASM2157AMASM2155AMASM2160A

BEVEL GEAR 12TBEVEL GEAR 15TBEVEL GEAR 24TBEVEL GEAR 37TPIN

GT14B METAL GEAR AND PINS SET489279314982214982

1114

MAT-016-BA-00013DCC-G00289DCL-G00318MASM090A

GT16MB PAINTED + DECORATED BODYSTICKER SHEETCARISMA LOGO STICKERSNAP PIN

GT16MB VOLKWAGEN BEETLE DESERT EDITONPAINTED + DECORATED BODY489279315139915139

11114

LCB-G00054DCC-G00289DCL-G00969DCL-G00318MASM090A

GT16MB CLEAR BODYSTICKER SHEETGT16MBMASKING SHEETCARISMA LOGO STICKERSNAP PIN

GT16MB VOLKWAGEN BEETLE DESERT EDITON CLEAR BODY SET489279315141215141

21219

MASM033AMASM083AMASM084AMASM270AME031A

BEARING 8x12x3.5mmBEARING 4x7x2.5BEARING 5x9x3mmBEARING 7x11x3mmBEARING 4x8x3mm

GT16MB / GT16MT BEARING SET489279315059015059

GT16MT HARDWARE SET15061 4892793150613

SSW-G00020SSW-G00034SSW-G00035SSW-G00053SSW-G00063SSW-G00066SSW-G00077SSW-G00081SSW-G00088SSW-G00100SSW-G00104SSW-G00144SSW-G00147SSW-G00158SSW-G00175SSW-G00190SSW-G00193SSW-G00228SSW-G00284SSW-G00285SSW-G00331SSW-G00454SSW-G00470SSW-G00659SSW-G00661

SCREW 2.6x10KBSCREW 2.6x12KBSCREW 2.6x12PBSCREW 2.6x6KB SCREW 2.6x6PBSCREW 2.6x6PWBSCREW 2.6x8KB SCREW 2.6x8PBSCREW 2.6x8PWMSCREW 2x6PWB D4.5SCREW 2x10PBSCREW 2x6PBSCREW 2x6KB SCREW 2x8PBSCREW 2.6x10PBSCREW 3x10KMSCREW 3x10PMSCREW 3x18BMSCREW 3x8PB SCREW 3x8PBSCREW M2x8KBSCREW 2.6x10cmSCREW 2x6KMSCREW 1.4x8KB D2.5SCREW 1.4x6KM D2.5

442113481424466485441424142

111111111151544422

GT16BEETLEP0601GT16BEETLEP0303GT16BEETLEP0602GT16BEETLEP0603GT16BEETLEP0604GT16BEETLEP0408GT16BEETLEP0409GT16BEETLEP060516MBP0303GT16BEETLEP0606SSW-G00190GT16BEETLEP0607MASM727ASSW-G00144SSW-G00104SSW-G00077SSW-G00035SSW-G00175

GT16 BEETLE FRONT BUMPERGT16 BEETLE TAIL PIPEGT16 BEETLE EXHAUST PIPE - AGT16 BEETLE EXHAUST PIPE - BGT16 BEETLE REAR BUMPERGT16 BEETLE EXHAUST PIPE MOUNT - LEFTGT16 BEETLE EXHAUST PIPE MOUNT - RIGHTGT16 BEETLE REAR CRASHGUARDGT16 MONSTER BEETLE REAR BUMPER EXTENSIONGT16 BEETLE FRONT BUMPER MOUNTSCREW 3x10KMGT16 BEETLE REAR BUMPER MOUNTM3 NUT (BLACK OXIDE)SCREW 2x6PB BLACK OXIDE (D=3.5)SCREW 2x10PBSCREW 2.6x8KB BLACK OXIDE(D=4.8)SCREW 2.6x12PBSCREW 2.6x10PB BLACK OXIDE (D=4.2)

GT16 MONSTER BEETLE BUMPER SET (UN-PAINTED)489279314919814919

4892793150026 M40B/M40DT LOCKNUT SET15002 M3 LOCKNUTM4 LOCKNUT

64

MASM1168AMASM1011A

4892793150095 CTX-2710 TRANSMITTER15009 CTX-2710 TRANSMITTER ASSEMBLY 1MAT-TXG-MB-00003

4892793152242 BODY CLIP SET (S/M/L)15224BODY CLIP LBODY CLIP MBODY CLIP S

444

MASM1366AMASM032AMASM090A

4892793152211 SET SCREW SET (M3x3 AND #5-40x1/8”)15221 M3 SET SCREW#5-40x1/8 SET SCREW

44

MASM038AMASM969A

4892793152334 FOAM WASHERS SET15233 FOAM WASHERS 4EVA-G00002

4892793148726 GT14 MK3 SLIPPER SPRING AND WASHER SET14872 1.2XID4.2XL5.9X 3.5TURN SLIPPER SPRINGSLIPPER WASHER

12

MASM1758AMASM1961A

4892793149129 GT14B INPUT PINION GEAR SHAFT14912 INPUT PINION GEAR SHAFTSCREW 2X6KM (D=3.5)

11

MASM2080ASSW-G00145

4892793149143 GT14B WHEEL LOCK PIN 1.5X7L14914 PIN 1.5X7L 8MASM245A

4892793149815 GT14B METAL GEAR DIFF SEAL SET14981 SLIPPER 19 x 14.1 x 0.5mm 2 SPC-G00007

4892793150491 GT10DT BALL STUD SET15049BALL STUD4.3 BALL 3.9 BALL

412 2

MASM1632AMASM1803AME017A

4892793150569 GT10DT OUTDRIVE CUP (PAIR)15056 OUTDRIVE CUP 2MASM2159A

4892793151740 GT16MT/ GT16MB / GT10DT DOG BONE SET15174 DOG BONE 4MASM2327A

4892793150460 GT10DT LOCKNUT SET15046LOCKNUT_M4_BLACK ZINCSERVO SAVER ADJUSTORM3.0 FLANGED LOCKNUT

114

MASM1011AMASM2006AMASM733A

4892793149792 GT14B METAL GEAR DIFF SET14979

SCREW 1.4X6KM_D2.5SCREW M1.4X8KB(D=2.5 )SLIPPER 19 x 14.1 x 0.5MMDIFF GEAR ADAPTOROUTDRIVE CUPDIFF GEAR 12TDIFF GEAR 24TDIFF GEAR 15TDIFF GEAR 37TDIFF GEAR 37TDIFF GEAR BOX

24122421121

SSW-G00661SSW-G00659SPC-G00007MASM2160AMASM2159AMASM2158AMASM2157AMASM2156AMASM2155AMASM033AGT14BPROP0701-01

4892793151092 M10DT LOCKNUT SET15109M3 SCREW NUT SCREW NUT M4 LOCKNUT

1225

MASM727AMASM313AMASM1932A

GTBP0201-01GTBP0202-01

ROD BALL CAPGTB ANTI ROLL BAR LINK

62GTB BALL CUP SET489279314939614939

4 9

22

GT14BP0401-02GT14BP0402-02

FRONT ARMSREAR ARMSGT14B SUSPENSION ARMS489279314729314729

11

SLIPPER PLATE ASLIPPER PLATE B

GT14BP0509GT14BP0510GT14B SLIPPER PLATE489279314733014733

111

GT14BP0701-01GT14BP0702-01GT14BP0703-01

SERVO SAVER CAPSERVO SAVER HORNSERVO SAVER ADAPTER

GT14B SERVO SAVER SET489279314736114736

14743 4892793147439 GT14B WHEEL SHAFT (PAIR) MASM1624A WHEEL SHAFT 2

14745 4892793147453 GT14B SLIPPER SHAFT MASM1626A SLIPPER SHAFT 122448

MASM1627AMASM1628AMASM2017AMASM1632AMASM269A

REAR HUB PINFRONT HUB PINARM PINARM PIN BALL HEADE-RING

GT14B HINGE PIN SET489279314746014746

MASM650ASSW-G00595

SERVO SCREW RODTIE ROD

16GT14B TIE ROD489279314755214755

14775 4892793147750 GT14B SPUR GEAR 66T 1GT14BP0704-01 SPUR GEAR 66T

2MASM1625A CENTER DRIVE CUPGT14B CENTER DRIVE CUP489279314744614744

RBP-G00010RBP-G00014RBP-G00012

SHOCK DIAPHRAGMO-RING 2.9x1.78mmO-RING

484

SHOCK O-RING SET14804 4892793148047

SPARE PARTS LISTITEM NO BARCODE PRODUCT NAME PART NO QTYDESCRIPTION

4892793147286 GT14B FRONT AND REAR HUB SET14728

LEFT REAR HUBLEFT SPINDLERIGHT REAR HUBRIGHT SPINDLESPINDLE CARRIER LEFTSPINDLE CARRIER RIGHT

111111

GT14BP0301-01GT14BP0302-01GT14BP0303-01GT14BP0304-01GT14BP0305-01GT14BP0306-01

Top Control Panel

Steering Reverse Switch

Dual Rate Dial

Throttle Reverse Switch

ReversingReversing is used to change the response direction of steering wheel and throttle trigger. CTX-2710 Transmitter features 2 reversing functions: Steering Reverse and Throttle Reverse.Steering Reverse: Reverse the response direction when operating steering wheel. Turning left steering wheel, the model turns right while turning right the model turns left.Throttle Reverse: Reverse the response direction when operating throttle trigger. Pushing forward throttle trigger the model moves backward while pulling back, the model moves forward. If necessary you can just use a small screwdriver to adjust the orresponding switches.

CTX-2710 features two trimming functions:Steering Trim and Throttle Trim.Steering Trim Dial : Adjust the neutral position of steering servo when the wheels are straight ahead. Normally steering trim is adjusted until the model can keep straight tracks.Throttle Trim Dial : Adjust neutral position of throttle servo. Make sure the model stays still when releasing the throttle trigger.

Trimming Dual Rate Dial enables to adjust the same maximum steering angle of servo on both sides (Left and Right) when model makes steering. The Dual Rate Dial affects the sensitivity of servo. Reducing dual rate value can lower the sensitivity of servo and reduce the same maximum steering angle on both sides. Remember to adjust the dual rate value within the adjustment range.

Dual Rate Dial

ST.TRIM

TH.TRIM

SYNC

1. Prior to any operation make sure the transmitter and receiver are both turned off.2. Press and hold the setup button on the receiver while power on the receiver.3. Release the setup button till green LED flashes.4. Press the setup button to select the frame rate with green LED flashing. Faster Flashing = High frame rate (7ms) for digital servo Slower Flashing = Low frame rate (15ms)for analogue servo5. Power on the transmitter. With the transmitter steering wheel and throttle trigger in neutral position (full stop and straight steering), press the SYNC button of the transmitter. 6. When synchronization is done, the green LED on both receiver and transmitter will turn solid on.

Synchronization & Frame Rate Adjust

Setup Key of Receiver

Carisma 2.4GHz Receiver MRX2800

Remarks : The mounting positions of receiver and antenna cable greatly affect the operating range.

Install the antenna vertically to the ground.

Auxiliary Port (Reserved)Steering Port : Where to plug in the servo. Throttle Port : Where to plug in the Electronic Speed Controller (ESC).Setup button : Synchronize transmitter and receiver. Select frame rate.

Steering Port

Throttle Port

Auxiliary Port (Reserved)

Warning : • Never bend the metal pins on the PCB of receiver.• Never cut the antenna cable.• Install the antenna vertically as shown in the figure.• Keep the antenna as far away from the motor, ESC and other noise sources as you possibly can.

Setup Button

Antenna Cable

MRX2800

Tips :• Wrap the receiver with something soft, such as foam rubber, to avoid vibration. If there is a chance of getting wet, put the receiver in a waterproof bag or balloon.

Synchronization Button

ABOUT THE RADIO SYSTEM

RECEIVER CONNECTION AND INSTALLATION

SYNC

Synchronization Button

4892793147309 GT14B BATTERY HOLD DOWN PART/ REAR WING MOUNT14730BATTERY HOLD DOWNREAR WING MOUNT FOR GT14B ONLYBATTERY HOLD POST

224

GT14BP0403-01GT14BP0404-01GT14BP0405-02

112

GT14BP0501GT14BP0505GT14BP0512

CENTER DRAG LINKSTEERING MOUNTSTEERING ARM

GT14B STEERING RACK489279314731614731

111211

GT14BP0503GT14BP0504GT14BP0506GT14BP0508GT14BP0511GT14BP0514

REAR CENTER MOUNTREAR SUPPORTSWAYBAR MOUNT CAP FOR GT14B ONLYWING BUTTON FOR GT14B ONLYANTI ROLL BAR MOUNT R FOR GT14B ONLYANTENNA HOLDER FOR GT14B ONLY

GT14B PLASTIC PARTS SET489279314732314732

1FRP-G00030 UPPER DECKGT14B UPPER DECK489279314750714750

123456789

101112131415

PART NUMBER DESCRIPTION QTYFRP-G00030GT14BP0501GT14BP0505GT14BP0512GT14BP0514GT14BP0603GT16MB VB-002GT16MB VB-002MASM1803AMASM480AMASM481AMASM623ASSW-G00063SSW-G00175SSW-G00331

FRP TOP PLATECENTER DRAG LINKSTEERING MOUNTSTEERING ARMANTENNA HOLDERFRONT SHOCK BRACEMIDDLE TURNBUCKLESERVO TURNBUCKLE4.3 BALL L=10.8KING PIN SHEX LONG KING PIN PRTBUSH2.6x6PB2.6x10PB M2x8KB

111211212226121

1212

4

10

1114

13

5

1

1212 9

158

3

7

2

9

6

11

14

14756

14750

14756

14756

14756

14735

14757

14757

14757

14731

14731

14731

14731

14732

1475715049

15049

10

4

7

UPPER DECK & STEERING POST ASSEMBLY

ASSEMBLEDGT16MB VB-009

15061

1506115061

15061

4892793143530 GT14 BALL STUD SET143534.3 BALL STUD4.3 BALL STUD3.9 BALL STUD

16 4 2

MASM487AMASM615AME017A

4892793146876 GT14B - TELFON SLIPPER PAD14687 SLIPPER SHEET 2SPC-G00005

4892793147347 GT14B - WHEEL HEX14734 WHEEL HEXWHEEL HEX B

42

GT14BP0507GT14BP0516

4892793147354 GT14B - HINGE PIN BRACE /SHOCK TOWER SUPPORT14735

GT16 MONSTER BAJA FRONT HING PIN BRACEFRONT OUTER HINGE PIN BRACEFRONT SHOCK TOWER SUPPORTREAR INNER HINGE PIN BRACEREAR OUTER HINGE PIN BRACEREAR SHOCK TOWER SUPPORTSERVO BRACESHOCK MOUNT SPACE

11111114

GT14BP0601-01GT14BP0602GT14BP0603GT14BP0604GT14BP0605GT14BP0606GT14BP0607GT14BP0515

4892793147408 GT14B - FRONT & REAR DIFFERENTIAL HOUSING14740 DIFF GEAR BOX LOWER HOUSING GEARDIFF GEAR BOX UPPER HOUSING GEAR

22

R14P1101-01R14P1102

4892793147415 GT14B - CENTER DOGBONE SET14741 CENTER DOGBONE (FRONT)CENTER DOGBONE (REAR)

11

MASM1621AMASM1623A

4892793147477 GT14B - STEERING BUSHING14747 STEERING BUSHING 4MASM1631A

4892793147521 GT14B - DIFF OUTDRIVE FOAM STUD14752 DIFF OUTDRIVE FOAM STUD 8EVA-G000034892793147545 GT14B - SERVO SPRING14754 SERVO SPRING �1.0X7.0X10LX4N 1MASM693A

4892793147484 GT14B - BALL DIFFERENTIAL GEAR SET14748

BEARING_8X12X3.5MMBEARING_4X7X2.5MMTHRUST BEARING F2-6(2X6X3)BALL DIFF SPRINGWASHER 8X10X0.2BALL DIFF WASHER3MM BALLDIFF OUTDRIVE FOAM STUDHM2X22 ZINK BLACKADJUST LOCK PART37T RING BEVEL GEAR(BALL DIFF)CENTRE DRIVE BEVEL PINION GEAR 19TBALL DIFF OUTDIVE ABALL DIFF OUTDRIVE B

2 2 1 1 2 210 2 1 1 1 1 1 1

MASM033AMASM083AMASM745AMASM2069AMASM1833AMASM1836AMASM1858AEVA-G00003SSW-G00370R14P0914GT14BP0902GT14BP0907MASM1845AMASM1846A

4892793147569 GT14B - KING PIN SET14756KING PIN SHEX LONG KING PIN

22

MASM480AMASM481A

4892793147576 GT14B - BUSHING14757 BUSHING 6MASM623A

4892793147712 GT14B - PINION GEAR 14T14771 14T PINION GEAR M3x3 SET SCREW

11

MASM671AMASM038A

4892793147989 4500KV BRUSHLESS MOTOR14798 4500KV BRUSHLESS MOTOR 1MOT-G000924892793147996 GT14B - MS903GT SERVO14799 MS903GT SERVO ASSEMBLY 1MAT-SVO-AS-000054892793148016 V6 TYPE R BRUSHLESS ESC14801 V6 TYPE R ASSEMBLY 1MAT-ESC-AS-00002

8 5

BRUSHLESS ESC V6 TYPE R FEATURES

Brus

hles

sM

otor

BrushlessElectronic

Speed ControllerV6 Type R

Power Switch

Battery PlugConnector

Bullet Connector

Setup Button

Steering Port

Throttle Port

Auxiliary Port(Reserved)

2.4GHz ReceiverMRX2800

Servo MS-903GT

• Auto Detect Brushed or Brushless Motor (Details see Select Motor Type)• One Touch End Points calibration• Battery Selection: - 7.4V 2 cells LiPo - 7.2V NiMH• Two ESC profile: - Forward / Reverse with Smart Brake - Forward Only• Battery Over Voltage Protection (Max Input voltage = 13V)• Thermal Protection• Motor Stall Protection

ESC Features:

• After Power On: Just after power on the ESC, the LED will display the currently selected Battery Type for 2 sec: - RED, GREEN LED are used to display Currently Selected Battery Type: RED LED Flashing = LiPo is selected GREEN LED Flashing = NiHM is selected• Battery Type Programming: During the battery type displaying 2 second as mentioned above, user can press the key to select other battery type. Cut-off voltage will be automatically adjusted according to the battery type selected: - For LiPo Battery: ESC will cut-off at 6V - For NiHM: ESC will cut-off at 4.3V

LED Indicator:

• LED Display during “Normal Operation”

ConditionStop GREENPartial Forward OFF

Partial Reverse OFFMax Forward RED

Max Reverse REDBrake RED + GREEN

LED

Step 1 - Turn on the Transmitter, Throttle at Stop position.

Step 2 - Hold the ESC setup key and then power on the ESC.

Step 3 - RED and GREEN LED will turn on, then release the setup key.

Step 4 - GREEN LED flashing, then hold Throttle at Full Throttle position until

GREEN LED become Solid ON.

Step 5 - Then RED LED will flashing.

Step 6 - Next hold Throttle at Max Reverse position until RED LED become

Solid ON.

Step 7 - Release Throttle to Stop position, programming done.

One Touch End-Points Calibration Programming:

LED Display For “Error”• Battery Voltage too high (over 13V) - RED LED solid on and GREEN LED flashing slowly (Can only happen during Power ON).• Overheat - Alternatively Flashing Red and Green• Motor Failure, eg. Motor wire broken, Bad motor, or Motor Jammed - RED LED flashing quickly 3 times, turn off and then repeat• Battery Low - GREEN LED solid on and RED LED flashing slowly

1234567891011121314151617181920

PART NUMBER DESCRIPTION QTY16MBP0301EVA-G00002FRP-G00063GT14BP0507GT14BP0515GT14BP0606GT16BEETLEP0301GT16MB VB-002GT16MB VB-003GT16MB VB-007GT16MB VB-008MASM090AMASM245AMASM313AMASM727ASSW-G00081SSW-G00175SSW-G00285SSW-G00193SSW-G00228

REAR SHOCK TOWER MOUNTEVA WASHERREAR SHOCK TOWERWHEEL HEXSHOCK MOUNT SPACERREAR SHOCK TOWER SUPPORTBODY POSTSREAR TURNBUCKLEREAR OIL SHOCK ASSEMBLYREAR SUSPENSION ARMS ASSEMBLYGEAR DIFFERENTIAL ASSEMBLY SNAP PINPINM3 LOCKNUT BLUE ZING PLATED M3 NUT(BLACK OXIDE)2.6x8PB 2.6x10PB 3x8PB 3x10PM 3x18BM

12122122211422232222

515

3

134

11

19

18

116

145

998

4

1013

6

19

8

7

2

7

18

20

1215

12

17

REAR GEAR BOX & OIL SHOCK ASSEMBLY

BATTERY PACK & CHARGER MANUAL

123456789

PART NUMBER DESCRIPTION QTYGT16MB VB-002GT16MB VB-003GT16MB VB-006GT16MB VB-008EVA-G00002FRP-G00062GT14BP0507GT14BP0511GT14BP0515

FRONT TURNBUCKLEFRONT OIL SHOCK ASSEMBLYFRONT SUSPENSION ARMS ASSEMBLYGEAR DIFFERENTIAL ASSEMBLYEVA WASHERFRONT SHOCK TOWERWHEEL HEXANTI ROLL BAR MOUNT RSHOCK MOUNT SPACER

221121212

10111213141516171819

PART NUMBER DESCRIPTION QTYGT16BEETLEP0301MASM090AMASM245AMASM313AMASM727ASSW-G00081SSW-G00175SSW-G00285SSW-G00193SSW-G00228

BODY POSTSNAP PINPINM3 LOCKNUT BLUE ZINC PLATEDM3 NUT(BLACK OXIDE)2.6x8PB2.6x10PB3x8PB3x10PM3x18BM

2422232222

7

2

1

14

9

10

5

18

2

7

3

10

11

1216

1218

1

6

13 15 174

8

19

11

1234567891011121314

PART NUMBER DESCRIPTION QTYEVA-G00003GT14BP0301-01GT14BP0303-01GT14BP0402-02GT14BP0604GT14BP0605MASM2327AMASM1624AMASM1627AMASM1632AMASM1803AMASM2017AMASM269AME031A

DIFF OUTDRIVE FOAM STUDLEFT REAR HUBRIGHT REAR HUBREAR ARMREAR SUSPENSION INNER BRACE REAR SUSPENSION BRACEDOG BONEWHEEL SHAFTHINGE PIN 27.2mmHINGE PIN BALL4.3 BALL L=10.8SUSPENSION HINGE PINM1.5 E-RING BLACK OXIDE BEARING 4x8x3mm

21121122242244

14

11

21

74

6

141114

8

13

8139

10

1210

1013

54

109

3

12

1

137

14

FRONT GEAR BOX & OIL SHOCK ASSEMBLY

REAR SUSPENSION ARMS ASSEMBLY

ASSEMBLEDGT16MB VB-011

ASSEMBLEDGT16MB VB-007

ASSEMBLEDGT16MB VB-012

15109

15224

15049

15047

15047

15047

15047

1505914743

15174

1472814752

14746

14729 1492915049

15223

15224

1522415109

15109

15019

14927

14735

14735

14735

14734

14914

1473414914

15049

14929

15049 1472915147

1475215049

14728

15059

15059

1474314746

1504914746

14746

15059

14914

15224

15233

14734

14734

14732

14926

14735

15061 15061

15061

15061

15061

Operation• Completely discharge a Nickel - Metal Hydride (NiMH) battery pack before you charge it. Frequent charging a Nickel - Metal Hydride battery pack that is not fully discharged can shorten its battery life.• The battery pack cannot be fully charged when it in low temperate environment.• To charge a very hot after use battery pack can permanently lose its ability to charge.• Unplug the charger from the mains outlet before attempting any maintenance or cleaning.

7.2V 1200mAhNiMH Rechargeable

Battery Pack

7.2V BatteryCharger

WARNINGTo reduce the risk of fire, electric shock or injury, carefully follw these instructions.

This manual contains important safety and operating instructions for your charger. Before using the battery charger, read all the following in this instructions manual on the battery chargers and the rechargeable batteries to be charged, and on the products that use the rechargeable batteries.

Plug supplied charger into mains outlet socket. Connect the 7.2V rechargeable battery pack to the charger. The charger’s connector fits only one way. Don’t force it! If the connectors do not fit together easily, be sure that you have positioned them properly. Average recharging time is approximately 2 to 3 hours maximum. When recharging is over, remove the charger from the household outlet. After recharging is completed, disconnect the battery pack from the battery charger.

The 7.2V battery pack is not supplied pre-charged and you must charge it before connecting the R/C car. The 7.2V battery pack and charger will get hot while charging. This is normal. Do not charge on, or near to, a material / surface that is flammable or can be damaged by heat. When the 7.2V battery pack out of power (dead battery), it should be replaced. Do not dispose in the household garbage but to the collection stations or at a special garbage depot.

CAUTION• The battery charger is not a toy.• Charger only Ni-MH type rechargeable batteries. Other types of batteries may explode and cause serious personally injury or damages.• Never let the charger or battery pack get wet or damp.• Overcharging can damage the battery pack. Follow the indicated recharging time.• Check the batteries regularly for leakage.• Non-rechargeable batteries are not to be recharged.• Do not disassemble the charger. Take it to a qualified service technician when service or repair is required. Improper reassembly may result in a risk of fire, electric shock, or injury to persons.• Do not recharge the battery pack while it is still hot after use. Wait until it has cooled down before recharge.• Use only the recommended batteries or batteries of equal quality.• Do not short circuit - all cables should be insulated. If necessary, use vinyl tape for insulation (NOT INCLUDED).• Do not leave battery pack charger unattended when charging.• The supply terminals are not to be short-circuited.• Packing has to be kept since it contains important information.• Do not expose the charger to rain or excessive moisture.• Do not operate the charger if it has received a sharp blow, or been dropped or damaged in any way. Take it to qualified service technician to repair.• To reduce the risk of damage to the AC plug and cord, disconnect the charger by pulling plug rather than the cord.• Do not use an extension cord. It could result in fire or electric shock.• Do not operate the charge if the cord or plug is damaged. Repair the charger. Never alter the provided AC cord or plug. If does not fit in the AC outlet, have a qualified service technician install the appropriate connector plug. Improper connection can result in an electrical shock. Never use the charger as a DC power source for any other electrical equipments.• Rechargeable battery pack can explode if under incorrectly or non stop charging.• Always observe the polarity to correctly connect : Positive (+) to Positive (+) Negative (-) to Negative (-).

150611506115061

15061

15061

15061

15061

14914

6 7

123456789

PART NUMBER DESCRIPTION QTYGT14BP1001GT14BP1002-01GT14BP1101-01GT14BP1102-01GT14BP1103-01GT14BP1104GT14BP1105-01GT14BP1108GT14BP1110

SHOCK TOP CAPOIL SHOCK BOTTOM CAPREAR SHOCK BODYFRONT SHOCK BODYSPRING CUPSHOCK ENDOIL SHOCK ADJUSTERSHOCK ADJUSTMENT CLIP SET 2mmSHOCK ADJUSTMENT CLIP SET 0.5mm

221122211

101112131415161718

PART NUMBER DESCRIPTION QTYGT14BPROP0101MASM053AMASM1684AMASM1685AMASM2151AMASM204AMASM1736ARBP-G00010RBP-G00014

SHOCK PISTON 1.3mmE-RING ID2.3 BLACK OXIDEFRONT SHOCK SHAFTREAR SHOCK SHAFTREAR DAMPER SPRING5.8 THROUGH BALL(5.79x4.6L)FRONT SHOCK SPRINGSHOCK DIAPHRAMO-RING ID2.9x1.78mm

241114124

65142

78

97

2 16 5

18

123456789

PART NUMBER DESCRIPTION QTY16MBP0302GT14BP0302-01GT14BP0304-01GT14BP0305-01GT14BP0306-01GT14BP0401-02GT14BP0601-01MASM2327AMASM1624A

FRONT SUSPENSION BRACE LEFT SPINDLERIGHT SPINDLESPINDLE CARRIER LEFTSPINDLE CARRIER RIGHTFRONT ARMFRONT SUSPENSION INNER BRACE DOG BONEWHEEL SHAFT

111112122

1011121314151617

PART NUMBER DESCRIPTION QTYMASM1628AMASM1631AMASM1803AMASM2017AMASM269AME031ASSW-G00454EVA-G00003

HINGE PIN 30.2mmSTEERING BUSHING4.3 BALL L=10.8SUSPENSION HINGE PIN M1.5 E-RING BLACK OXIDE BEARING 4x8x3mm2.6x10cmDIFF OUTDRIVE FOAM STUD

24424442

16

12

17

814

13

1

13

78

12

12

15

1116

59

16

15

2

114

15

11

9

66

17

12 12

1014

14

14

10

15

3

16

11

66.

5 ±0

.3

70.

5 ±0

.3

FRONTOIL SHOCK

REAROIL SHOCK

REAROIL SHOCK

FRONTOIL SHOCK

15

156

123456789

101112131415161718192021

PART NUMBER DESCRIPTION QTYSSW-G00661SSW-G00659SSW-G00147SSW-G00063SPC-G00007R14P1102R14P1101-01MASM2160AMASM2159AMASM2158AMASM2157AMASM2155AMASM1803AMASM033AGT14BPROP0701MASM2080AMASM084AMASM1625AMASM038ASSW-G00470MASM2156A

1.4x6KM D2.51.4x8KB D2.5 2x6KB 2.6x6PBGEAR DIFF. SEAL SHEETUPPER DIFF. HOUSING CASE LOWER DIFF. HOUSING CASE PINOUTDRIVE CUPBEVEL PINION 12TBEVEL PINION 24T37T GEAR4.3 BALL L=10.8BEARING 8x12x3.5mmDIFFERENTIAL GEAR BOXINPUT SHAFTBEARING 5x9x3mmCENTER DRIVE CUPM3x3 SCREW2x6KM BEVEL PINION 15T

242211122421221121111

134

4

8

8

9

7

10

11 15

14

3

6

13

10

1

1

11

21

5

16

12

19 17

20

18

14

9

2

2

1234567891011121314151617181920

PART NUMBER DESCRIPTION QTYFRP-G00064GT14BP0403-01GT14BP0405-02GT14BP0502GT14BP0503GT14BP0504GT14BP0607GT16MB VB-004GT16MB VB-005MASM090AMASM671AMOT-G00092SSW-G00053SSW-G00077SSW-G00088SSW-G00147 16MBP0401MASM038AMRX2800DCL-G00233

FRP CHASSIS PLATEBATTERY HOLD DOWNBATTERY HOLD POSTREAR CENTER BEARING BRACE REAR CENTER MOUNTREAR SUPPORTSERVO BRACEMAIN DRIVE SHAFT/SLIPPER UNITSERVOSNAP PINMOTOR GEAR 14T370 BRUSHLESS MOTOR2.6x6KB 2.6x8KB 2.6x8PWM 2x6KB 370 MOTOR MOUNTM3x3 SCREW2.4GHz RECEIVERDOUBLE SIDE STICKER

12411111141174241111

1413

12

7

9

1

10

16

3

1715

8 5 4

2

6

2

318

14

13

13

10

11

3

2019

MAIN CHASSIS ASSEMBLY

FRONT SUSPENSION ARMS ASSEMBLY

DIFFERENTIAL GEAR BOX ASSEMBLY

FRONT AND REAR OIL SHOCK ASSEMBLY

3

4

13

12

11

10

10

17

17

115

1

15

12345

PART NUMBER DESCRIPTION QTYGT14BP0807-01GTBP0201-01MASM650AME017ASSW-G00595

BALL CAPROD BALL CAPM2xL20mm3.9 BALLTURNBUCKLE (M3x38mm)

26123

1234567

PART NUMBER DESCRIPTION QTYGT14BP0509GT14BP0510GT14BP0704-01MASM038AMASM083AMASM1011AMASM1625A

SLIPPER PLATE ASLIPPER PLATE BSPUR GEAR 66TM3x3 SCREWBEARING 4x7x2.5mmLOCKNUT M4 BLACK ZING CENTER DRIVE CUP

1112112

891011121314

PART NUMBER DESCRIPTION QTYMASM1626AMASM1961AMASM270AMASM716AME014AME031ASPC-G00005

SLIPPER SHAFTSLIPPER WASHERBEARING 7x11x3mmSPRING WASHERPIN 1.5x6.0LBEARING 4x8x3mmSLIPPER SHEET

1211212

7

411

6

2

3141

8

4

7

12

513

14 10

9

23.2

±0.2

24±0

.2

11.7

±0.123

.2±0

.2

2

5 14755

1473914739

2 14739

14739

14755

14353

14736

15061

14754 14736 14736

15059 1505915221

1477414745

14733 1468714775

14687 14733 15059

14696

15002 14744

15221 1492214922

14922 1492214922

14922

15056

15049

15049

14740

1498214982

14982

14982

14982

14740

14979

15059

15056

14982

15221

14744

15059

1498114982

1491214982

15059

14922 1492214922

1492214922

149221492214922149221492214922

14922149221492214922

1492214922

14922 14922

149221492214922

1473214732

14730

14730

14730

14924

1477114771 14730

14732

15224

15049

1505914728

1474714743

14728

14746

14746

14929

14746

14729

1492914728

15049

1474315049

1475214747

15059

14728 14747

15059

14729 14746

1475215059

1504914747

15174

15174

15047

15047

15047

1504714928

14799

14735

15224

14798

14799

14739

147555 5

2

147392

1

3

4

1

324

1

6

5

123456

PART NUMBER DESCRIPTION QTYGT14BP0701-01GT14BP0702-01GT14BP0703-01MASM693AMS-903GTSSW-G00284

SERVO SAVER CAPSERVO SAVER HORNSERVO SAVER ADAPTER(JR)SERVO SPRINGSERVO3x8 PB

111111

TURNBUCKLE ASSEMBLY

MAIN DRIVE SHAFT/SLIPPER UNIT ASSEMBLY

SERVO SAVER EXPLODED DIAGRAM

ASSEMBLED GT16MB VB-013

ASSEMBLEDGT16MB VB-004

ASSEMBLEDGT16MB VB-005

ASSEMBLEDGT16MB VB-013

ASSEMBLEDGT16MB VB-008

ASSEMBLEDGT16MB VB-006

Front Turnbuckle

MiddleTurnbuckle

RearTurnbuckle

ServoTurnbuckle

14730

15061

15061

15061

15061

15061

15061

1506115061

15061

15061

15061

15061

15061

15061

15061

1506115061

15061