hacking minecraft on the raspberry pi using python lesson 5 1
TRANSCRIPT
Hacking Minecraft on the Raspberry Pi using Python
Lesson 5
1
Starter• Switch on your Raspberry Pi. • Open Minecraft• Open Idle (not Idle 3)• Click on File>New File• This opens up the Idle editor where you can
write and edit your Python code• Open Minecraft>Create New World (Minecraft
must be open for you to hack it)
2
3
Objective of the lessonUse Python to control a game called Minecraft
• All of you will:– Use Python to freeze water when you walk on it
• Most of you will:– Use a Pibrella to make a light and buzzer sound when you freeze the
water– Change the block types changed
• Some of you will:– Change the block from sand to grass only when the Pibrella
moisture sensor is in water
Type the following into the editorYou always use these lines first in your Minecraft code
This connects your code to Minecraft so that you can hack it. Careful, Python code is case sensitive
Remember to have Minecraft open)
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()
You need to add a loop which keeps checking to see if you are stood on water
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()
Did you get it correct? Did you remember the capital T and the :
We need to declare the water (Block ID 9) and ice (Block ID 79)
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True:
Did you get it correct?Did you remember to indent after a line of code
ending in :
We can now use the words water and ice to represent these blocks
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79
We now need to get the players position. We will declare it as pos
We can now declare the player’s pos.x, pos.y and pos.z as just x,y and z to make our coding easier
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79 pos = mc.player.getPos()
Did you get it correct?
Our current coordinates are x,y,zWhat are the coordinates of the block one below our feet?
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x
Did you get it correct?the coordinates of the block one below our feet is
(x,y-1,z)
We can get this block ID by using the line of codeblock = mc.getBlock(x,y-1,z)
We have now declared it as ‘block’
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z)
We will now need to add a line of code using ‘if’ to see if the block under our feet, now declared as ‘block’ is the same as == to the water block ID
now declared as ‘water’
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z)
Did you get it correct?
Did you remember to indent it?Did you remember the : at the end of an if line of code
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == water:
Now add a line of code to set down an ice block in place of the water
Can you explain this line of code?
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == water: mc.setBlock(x,y-1,z,ice)
Press F5 to save and run the programWhen you walk over water it should now change
to ice
What you have learnedgetBlock() The getBlock() function finds the type of a block at certain
co-ordinates. The co-ordinates are given as x, y andz variables. The function returns the block
type at those co-ordinates.if statement An if statement will only run a section of code when a
condition is True. When the condition is False, the section ofcode will not run. For example in our program the block below
the player will only turn to ice if it is water.Equal to (==) The equal to operator checks whether one value is the
same as the other. In our program we usean equal to operator with an if statement to check whether
the block below the player is water.
Challenge 1We will now get a Pibrella green light to come on if a water block is changed to ice. The green light must go off again 0.1 seconds
later
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == water: mc.setBlock(x,y-1,z,ice)
Challenge 1Did you get it correct?
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()import timewhile True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == water: mc.setBlock(x,y-1,z,ice) pibrella.light.green.on() time.sleep(0.1) pibrella.light.green.off()
Challenge 1Now make the buzzer sound at the same time with a frequency of
1000 to represent water freezing and then go off
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()import time while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == water: mc.setBlock(x,y-1,z,ice) pibrella.light.green.on() time.sleep(0.1) pibrella.light.green.off()
Challenge 1Did you get it correct?
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()import time while True: water = 9 ice = 79 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == water: mc.setBlock(x,y-1,z,ice) pibrella.light.green.on() minecraft.buzzer.buzz(1000) time.sleep(0.1) pibrella.light.green.off() pibrella.buzzer.off()
Challenge 2Can you change the code so that when you stand on sand (Block
ID 12) it changes to grass (Block ID 2)
Challenge 2Did you get it correct?
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()import timewhile True: sand = 12 grass = 2 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == sand: mc.setBlock(x,y-1,z,grass) pibrella.light.green.on() minecraft.buzzer.buzz(1000) time.sleep(0.1) pibrella.light.green.off() pibrella.buzzer.off()
Challenge 3You need the moisture sensor to change sand to grass. Add a
moisture sensor to the Pibrella on input A. Change the code so that the sand only changes to grass if the
moisture sensor is in water
Challenge 3Did you get it correct? Did you remember the : and indent correctly
import mcpi.minecraft as minecraftmc = minecraft.Minecraft.create()import time while True: if pibrella.input.a.read() : sand = 12 grass = 2 pos = mc.player.getPos() x = pos.x y = pos.y z = pos.x block = mc.getBlock(x,y-1,z) if block == sand: mc.setBlock(x,y-1,z,grass) pibrella.light.green.on() minecraft.buzzer.buzz(1000) time.sleep(0.1) pibrella.light.green.off() pibrella.buzzer.off()