Handles loads up to 750oF (400oC)

Superior Abrasion Resistance

Lower Cost-Per-Tonnage

Reliable Vulcanized Splices

Manufactured to Width

Run hotter loads longer

Hamaheat High Heat BeltsFor decades plants like yours have been forced to cope with conveyor belts that quickly crack and blister under high heat conditions. The resulting carry-back, clean-up and maintenance costs have been a constant problem.

Finally, a new breed of belt is changing all that.

Over half a century of research and development has produced a belt with advanced construction, providing durability under extreme material temperatures as high as 750oF (400oC). The Hamaheat Belt gives you superior abrasion resistance in severe conditions, the lowest cost-per-tonnage and the best ROI in the business.

Breakthroughs in heat tolerance, abrasion resistance and splice adhesion properties have been industry-proven throughout the world in cement plants, lime kilns, potash manufacturing, foundries, coke oven plants, iron ore pelletizing and other high heat applications. Shouldnt you be getting this kind of performance, durability and results from your belt?

Advanced construction withstands heat up to 750oF (400oC)Hamaheat belts resist hardening and cracking while carrying fine or coarse loads up to 750oF (400oC)*. Laboratory tests show that in high-heat conditions Hamaheat belts maintain cover tensile strength almost five times greater than the two leading brands. Improved cover performance under extreme heat extends the life of your belt while minimizing material carry-back. Clean-up and maintenance costs associated with premature cracking & blistering are greatly diminished.

Hamaheat belts resist the cupping and/or curling tendency of typical high-temp belts allowing for better belt tracking and reduced edge damage. All while enhancing the overall safety of your operation.

*Maintaining a belt surface temperature under 400oF will maximize belt life.

50 Years of research gets you 750oF of performance.

Proprietary polymer and

adhesion technology

allows you to run

hotter loads for longer

time periods.

From less downtime and dramatically longer belt life to reliable splices and reduced maintenance hours spent, Hamaheat belts have allowed us to use our resources more efficiently for over five years now. To say that Hamaheat has made a big improvement to our operation would be an understatement.

~ Ken Upchurch, Maintenance Supervisor TXI Midlothian Cement

Index = 100

LEADINGBRAND A

LEADINGBRAND B

HAMAHEATS-100

0 25 50 75 100 125 150

100

88

45

Superior abrasion resistance under extreme conditionsIn comparison with conventional leading brand high-heat EPDM belts, Hamaheat belts show significantly less cover loss in abrasion tests (DIN 53516). (See top graph.)

Lowest cost-per-tonnage and best ROIIn side-by-side tests with conventional EPDM high-heat belts, Hamaheat belts lasted significantly longer carrying a wide variety of high-heat materials. The Hamaheat advantage gives you greater peace-of-mind and optimum ROI.

Vulcanized splices remain intact for the life of your beltHamaheat adhesion values actually increase with heat so you can count on splices to last the life of your belt when properly vulcanized. Hamaheat belts eliminate the need for mechanical splices, allowing you to take advantage of belt cleaners and further reduce the cost cycle associated with carry-back material and clean-up.

Run true with molded edges manufactured to widthConventional high-heat belts are often slit from wider rolls. Thats why its not uncommon for belts to have some camber, requiring more time to train initially. In contrast, Hamaheat belts are manufactured to width with molded edges so you never get a hooked belt. Theyre good to go from the moment theyre installed. And they continue to perform like no other belt on the market.

Extreme-heat carcass design Hamaheats extreme heat technology strength starts at the core. The carcass is made from a proprietary fabric and dipping process that resists delamination and flexural fatigue.

Contact us for a thorough consultation to match the right belt for your operation.

Top cover DIN abrasion test:less is better Measures volume loss of cover rubber. Higher number (more volume loss) = less abrasion resistance.Test methods: 365oF (180oC) after 168 hours operation.

HAMAHEAT by Yokohama

50 Years of research gets you 750oF of performance.

Side-by-side comparison

0 100 200 300 400 500 600 700

100

172

640

Top cover % elongation at break: Elongation/elasticity of cover rubber is important to belt performance and service life. Competitors EPDM belts rapidly deteriorate under high temps. Hamaheats cover rubbers retain elasticity. Result: maximum performance and service life.Test methods: 365oF (180oC) after 168 hours operation.

0 100 200 300 400 500

100

92

420

Top cover tensile strength: Maintaining tensile strength of cover rubber is important to a belts performance and service life. Competitors EPDM belts quickly weaken under high temps. Not Hamaheat cover rubbers.Test methods: 365oF (180oC) after 168 hours operation.

Top cover to ply adhesion: Adhesion from cover to ply and from ply to ply is critical to extending belt life and performance. High adhesion ensures splice integrity and resistance to flexural fatigue. Hamaheat outperforms.Test methods: 302oF (150oC) after 168 hours operation.0 100 200 300 400 500 600 700

100

333

633

Index = 100

LEADINGBRAND A

LEADINGBRAND B

HAMAHEATS-100

0 25 50 75 100 125 150

100

88

45

NOTICE: Yokohama Rubber Company (YRC) supplies data, specifications and test results, both verbal and written, as a service to our customers. As operating conditions and conveyor designs vary from system to system, no representation or warranty is made by YRC that the representative data, specifications or test data provided herein are applicable to any specific or individual system.

Hamaheat is a registered trademark of the Yokohama Rubber Co. Ltd.

Head Office1638 Fosters Way, Delta, BC V3M 6S6Tel: 604.540.1950 Email: info@belterra.ca

On our most extreme high-heat clinker belts we simply havent had anything last as long and perform as good as Hamaheat belts.

~ Dennis Davis, Maintenance Planner, CEMEX

Vulcanized splices that last the life of the belt, less wear and tear on the system from carry-back, increased belt life, and savings on maintenance man-hours are the main benefits we have realized using Hamaheat belts.

~ Tony Guettner, Maintenance Superintendent, Capitol Cement

From our customers

Nanaimo

1945B Bollinger Road Nanaimo, BC, V9S 5W9 Tel: 250.741.0094

Prince George

2247 South Quinn Street Prince George, BC, V2N 2X4 Tel: 250.562.1245

Kamloops

1180 Ord Road Kamloops, BC, V2B 7V4 Tel: 250.376.1125

Kelowna

155 Cambro Road Kelowna, BC, V1X 7T2 Tel: 250.765.6300

Edmonton

9741 49th Street Edmonton, AB, T6B 2L8 Tel: 780.462.3245

Calgary

#20, 700 58th Avenue S.E. Calgary, AB, T2H 2E2 Tel: 403.253.9333

Grande Prairie

9515 116th Street Grande Prairie, AB, T8V 5W3 Tel: 780.539.0478

Leduc Project Division

#103 8009 39th Street Leduc, AB, T9E 0B3 Tel: 780.980.2845

Regina

157 Leonard Street North Regina, SK, S4N 5X5 Tel: 306.546.2400

Saskatoon

302-50th Street East Saskatoon, SK, S7K 6X2 Tel: 306.244.2400

Winnipeg

1525 Dublin Avenue Winnipeg, MB, R3E 3N2 Tel: 204.694.3322

Thunder Bay

1040 Gorham Street Thunder Bay, ON, P7B 5X5 Tel: 807.623.4990