hand hygiene sink - ipac canadas/2013-06... · 2016-09-28 · 2012-09-24, z8000 compliant...
TRANSCRIPT
2012-09-24,
Z8000 Compliant Antimicrobial Hand Hygiene Sink. 18 gauge (1.2mm) type 304 stainless steel. Left rear waste location to prevent water from splas-hing directly into the waste from both the faucet and during hand washing. Integral 1 1/2” (DN 40) tailpiece is welded to the bottom of the basin. Waste is left open and shaped to prevent the assembly of plugs, strainers and anti-splash fittings which are not allowed by the Z8000 guidelines. High back and side walls contain splashing and protect adjacent surfaces from contamination. Recommended for laminar flow, user temperature controlled deck mounted faucet. Due to the strength and lightness of stainless steel, an in wall carrier is not required and the sink can be carried and installed by one person. A wall hanger bracket is used to mount the sink to the wall. This fixture is coated with SANIGUARD® product protection. SANIGU-ARD® product protection is applied to all exposed surfaces of the sink. This treatment utilizes a silver ion technology to inhibit the growth of bacteria, molds and mildews. Silver ions are only released in the presence of bacteria-laden moisture and disrupt the metabolic and reproductive cycles of the micro-organisms.
TECHNICAL DATA
Material thickness grade 18 gauge (1.2 mm) Surface treatment Saniguard Bowl finish satin finished Gross weight 15 kgType of waste kit integral tailpiece Splash back yes Undercoated no Waste hole position rear left Splash back height 8" (203 mm)Overflow no Certificates and approvals cUPC approval, LEED MR credit 4:
recycled content (1-2 points), post-consumer-recycled 56%, pre-consumer recycled 31%
Franke CS
Franke Commercial Systems [email protected] www.franke-commercial.com
HAND HYGIENE SINKHWS1414P-00
N99© 2012 AS America Inc. Rev. 4/12
ICU SINK SYSTEMWITH SELECTRONIC® ICU FAUCET
WITH EVERCLEAN®
ICU SINK SYSTEM WITH SELECTRONIC® ICU FAUCET
❏ 9118.100 ICU Sink System with AC powered Selectronic® Faucet
❏ 9118.150 ICU Sink System with DC (battery) powered Selectronic® Faucet
❏ 9118.111 ICU Sink (fixture only)
SINK:• Vitreous china• Permanent EverClean® surface inhibits the growth of
stain & odor causing bacteria, mold & mildew• Deep basin & sloped ledges minimize splashing• Sink drain is offset so that the water stream does not
fall directly on the grid drain• Sink is designed with sealed overflow to eliminate
an area for water to pool• Includes removable acrylic shroud (with mounting
hardware) to allow access to the faucet electronics• Includes offset grid drain & P-Trap with
SANIGUARD®** coating **SANIGUARD is a registered trademark of the Component Hardware Group, Inc.
SELECTRONIC® FAUCET:• Hygienic hands-free operation • Rigid gooseneck spout with 5" reach• 1.5 gpm laminar flow restrictor in spout shank - No mix of
air & water• Plain spout end - Nothing on the end of the spout to
collect lime & debris Power Options: • Plug-In - 9118.100 System: Includes universal low
voltage transformer (80-250 VAC, 50-60 Hz) with 6' long cord. One transformer can run up to 15 faucets and/or flush valves in series.
• DC (Battery) - 9118.150 System: Includes CR-P2 Lithium battery. Battery Life - Approx. 200,000 cycles (4 years @ 4,000 cycles per month)
• Fully enclosed, water resistant & hermetically sealed electronic controls
• Vandal-resistant durable brass construction• Integral in-line strainer prevents clogging • Factory-installed 15" long S.S. flex hose with 3/8"
compression connection • Lead Free: Faucet contains ≤ 0.25% total lead content
by weighted average
• Optional thermostatic mixing valve (605XTMV) is available & must be ordered separately
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
Nominal Fixture Dimensions:509 x 432 x 663mm (20" x 17" x 26-1/8")
Fixture Compliance Certifications -Meets or Exceeds the Following Specifications:• ASME A112.19.2-2008 / CSA B45.1-08 for
Vitreous China Fixtures
Valve Listings:• ANSI A117.1• ANSI A112.18.1• CSA B 125• NSF 61/Section 9, Annex G
DISCLAIMER: Faucets with a base diameter greater than 2-1/4" (57 mm) will not fit on this ICU Sink. The Selectronic ICU Faucet was specifically designed to minimize splashing during operation. American Standard will not be liable for any splashing that occurs if faucets other than the American Standard ICU Faucets are used.
N100© 2012 AS America Inc. Rev. 4/12
ICU SINK SYSTEMWITH SELECTRONIC® ICU FAUCET
WITH EVERCLEAN®
14-3/4"(375mm)
17"(432mm)
4-3/4"(121mm)
5/8"(14mm)
1-5/8"(41mm)
20"(509mm)
4-3/4"(120mm)
8" (203mm)
1/2" DIA.(13mm)
FINISHED WALL
BASE MOUNTDETAIL
FINISHEDFLOOR
FINISHEDFLOOR
FINISHEDFLOOR
26-1/8"(663mm)
36"(914mm)
36-1/2"(927mm)
36-1/2"(927mm)
40-1/8"(1020mm)
2-3/4"(70mm)
9/16" DIA.(14mm)
2-3/4"(70mm)
4"(102mm)4"
(102mm)
MOUNTINGSTUDS
*FAUCET PERCH2-1/2" DIA. (65mm)
*FAUCET PERCH2-1/2" DIA. (65mm)
8"(203mm) BETWEENMOUNTING HOLES
114mm(4-1/2)
500mm(20") 1524mm
(60)
413mm(16-1/4)
3/8" COMP.
32mm(1-1/4) DIA.
125mm(4-7/8)
81mm(3-3/16)
60mm(2-3/8) MAX.
MOUNTINGSURFACE
(243mm)9-9/16"
(127mm)5"
(133mm)5-1/4"
(53mm)2-1/8" DIA.
RECOMMENDED CARRIERS:
JAY R. SMITH MFG. CO.MODEL SQ-0-4437 FLOOR MOUNTED SINK SUPPORT
WATTS CA-311 FLOOR MOUNTED URINAL CARRIER
MEDIC
HANSAMIX-S Electronic faucet, solar with battery support
Sensory operation (infrared)Robinet électronique avec cellule photovoltaïque et pile en support
Déclenchement optoélectronique (infrarouge)
Specifications:
Flow rate: 6 l/min, at 45 psi hydraulic pressureBody: DR brass Laminar stream nozzle Solenoid valve Sensor sensitivity: permanently self-adjusting Water flow duration: 0,5-0,4 seconds (pre-set: 1,6 seconds) Adjustable mixed water temperature with lateral handle (fixed setting possible)Rapid installation system Two flexible connection hoses and dirt-collecting filtersNon-return valves integrated into the faucet’s bodyProjection: 4 3/8” (111 mm)Solar cell and 6V Lithium DL 223AApproximate durability of battery: 5 years Resistant to 80°C temperature for thermal shock disinfection
Spécifications :
Débit : 6 l/min, mesuré à une pression d’écoulement de 45 psiCorps de robinet : laiton résistant à la dézincificationBrise-jet laminaireÉlectrovanneSensibilité des capteurs : réglage automatique et permanentDurée d’écoulement : 0,5-4 secondes (préréglage : 1,6 secondes)Température d’eau mitigée réglable avec manette latérale (réglage fixe possible)Kit de fixation expressDeux flexibles de raccordement armés et filtres anti-impuretésClapets anti-retour intégrés dans le corps du robinetSaillie : 4 3/8 po (111 mm)Cellule photovoltaïque et pile 6V Lithium DL 223ADurée de vie approximative de la pile : 5 ansRésistant à une température de 80°C pour désinfectionpar choc thermique
HANSAMEDIC 21
HANSA
Approbation
Optional accessories / Accessoires optionnels
Plate / Plaque 6”Model / Modèle 906215
Plate / Plaque 8”Model / Modèle AL800
Model Modèle Finish Fini
5077 2220Chrome Chromé
HANSA
Ordering Code:
www.wattscanada.ca Ph 888-208-8927 Fax 888-479-2887 Revision A 08/27/04
P4008P-Trap Adjustable 1-1/2" Plated
P4008 Specification: Commercial grade cast brass 1-1/2" (38
mm) adjustable p-trap. Assembly includes a resilient polished
chrome plated finish, deep wall flange and cleanout.
P4008 Model Shown
P4008
Minimum Flow Rate ...................................... 9.4 GPM (36 L/Min)
Shipping Weight ................................................... 2.5 Lbs (1.1 Kg)
INLET FOR 1-1/2 (38) DIA. TUBE
2" SLIDING ADJUSTMENT
9 (228)
4-3/16 (107)
2-1/2 (64)
3 (76) DIA
1-1/2 (38) DIA.
Dimensions shown in inches (mm) are for reference only and are subject to change.
282 www.wattscanada.ca Ph 888-208-8927 Fax 888-479-2887 Revision A 08/27/04
Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation.Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability.
Refer to www.specselect.com for individual models. Note: Use this page front and back as a product submittal sheet.
Approvals:• CSAcertified• CompliestoASMEA112.18.1(ContactDeltaRepresentativeforStateand/orLocalApprovals.)
Specification: (example)o 47T2312
Pair of heavy pattern, chrome plated finish, angle lavatory supplies, oval handle, stuffing box cartridge, 3/8” IPS brass inlet supply nipple, 9.5mm (3/8") OD x 305mm (12") long flexible riser tube, stainless steel wall flange.
o 47T2312SD Pair of heavy pattern, chrome plated finish, angle lavatory supplies, lockshield, screwdriver slot, stuffing box cartridge, 3/8" IPS brass inlet supply nipple, 9.5mm (3/8") OD x 305mm (12") long flexible riser tube, stainless steel wallflange.(Forstopvalveonly,seeBackPage,060853A)
Specification: (example)o 47T2512
Pair of heavy pattern, chrome plated finish, angle lavatory supplies, oval handle, stuffing box cartridge, 3/8" IPS brass inlet supply nipple, 9.5mm (3/8") OD x 305mm (12") long flexible braided stainless steel riser, stainless steel wall flange.
o 47T2512SD Pair of heavy pattern, chrome plated finish, angle lavatory supplies, lockshield, screwdriver slot, stuffing box cartridge, 3/8" IPS brass inlet supply nipple, 9.5mm (3/8") OD x 305mm (12") long flexible braided stainless steel riser, stainless steel wall flange. (For stop valve only, see BackPage,060853A)
o 47T2512SD-LR (Same as 47T2512SD, but less riser)
Specification: (example)o 47T2622
Pair of heavy pattern, chrome plated finish, angle lavatory supplies, oval handle, stuffing box cartridge, 1/2" IPS inlet, 12.7mm (1/2") OD x 305mm (12") long flexible riser, stainless steel wall flange. (No inlet supply nipple)
o 47T2622SD Pair of heavy pattern, chrome plated finish, angle lavatory supplies, lockshield, screwdriver slot, stuffing box cartridge, 1/2" IPS inlet, 12.7mm (1/2") OD x 305mm (12") long flexible riser, stainless steel wall flange. (No inlet supply nipple)
Specification: (example)o 47T2712SD
Pair of heavy pattern, chrome plated finish, angle lavatory supplies, lockshield, screwdriver slot, stuffing box cartridge, 1/2" nominal (5/8" OD) copper compression inlet, 9.5mm (3/8") OD x 305mm (12") long flexible riser tube, stainless steel wall flange. (No inlet supply nipple)
47T2312
47T2512
47T2312SD
47T2512SD
47T2622
47T2622SD
47T2712SD
®
Engineer/Architect Approval
Model Specified:
Approval: Date:
DSP–47T Rev. B Page 8.C.3
Note: Measurements may vary ± 6mm (0.25")
Lavatory Supplies
DSP–47T Rev. B
Refer to www.specselect.com for individual models. Note: Use this page front and back as a product submittal sheet.
Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation.Dimensions are for reference only. See current full-line price book or www.specselect.com for finish options and product availability.
Specification: (example)o 47T1316
Heavy pattern, chrome plated finish, angle closet supply, oval handle, stuffing box cartridge, 3/8" IPS brass inlet supply nipple, 9.5mm (3/8") OD x 305mm (12") long flexible riser, stainless steel wall flange.
o 47T1316SD Heavy pattern, chrome plated finish, angle closet supply, lockshield, screwdriver slot, stuffing box cartridge, 3/8" IPS brass inlet supply nipple, 9.5mm (3/8") OD x 305mm (12") long flexible riser, stainless steel wall flange.
o 060853A One only angle stop valve for 47T1316SD and 47T2312SD complete with 3/8" compression nut and sleeve.
Specification: (example)o 47T1326SD
Heavy pattern, chrome plated finish, angle closet supply, lockshield, screwdriver slot, stuffing box cartridge, 1/2" IPS inlet, 12.7mm (1/2") OD x 305mm (12") long flexible riser, stainless steel wall flange. (No inlet supply nipple)
Approvals:• CSAcertified• CompliestoASMEA112.18.1(ContactDeltaRepresentativeforStateand/orLocalApprovals.)
47T1316SD
47T1316
47T1326SD®
Engineer/Architect Approval
Model Specified:
Approval: Date:
Note: Measurements may vary ± 6mm (0.25")
Closet Supplies
Page 8.C.4 DSP–47T Rev. BDSP–47T Rev. B
ES-WD-CA-311,321 CANADA 0403 (Dimension) Denotes Millimeters
CA-311, 321
CA-311
Urinal Carriers
Job Name
Job Location
Engineer
Contractor
Contractor's P.O. No.
Representative
Tag:
SPECIFICATION: Watts Drainage Products CA-311 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet, universal steel hanger support plate, and plated hardware.
CA-321 SPECIFICATION: Watts Drainage Products CA-321 floor mounted urinal carrier with heavy gauge steel uprights with integral welded feet, universal steel hanger support plate and bottom bearing plate, and plated hardware.
42"(1067)
20-1/2"(521)
4-1/2"(114)
3-1/4"(83)
FIXTURE HANGERSUPPORT PLATECA-311 ASSEMBLYWHEN USED WITHOUTLOWER PLATE.CA-321 ASSEMBLYWHEN USED WITH LOWER PLATE
TO SUITFIXTURE
ROUGH-IN
LOWERBEARING PLATE
BACK OFSUPPORTBRACKET
FRONT OFSUPPORTINGPLATE
RECTANGULARSTEEL STRUCTURALUPRIGHTS
HEAVY DUTYSTEEL FOOT SUPPORTS
FIXTUREHANGERSUPPORTINGSTUDS
BEARING STUDSNOT ATTACHEDTO FIXTURE
1" x 2"(25 x 51)
NOTE: FOOT SUPPORTS SHOULD BESECURELY ANCHORED TO FLOORWITH 1/2" BOLTS AND ANCHORSBY OTHERS.
NOTE: Recommended for support of wall-hung urinals independent of wall.
WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and modifications to productspreviously or subsequently sold. See your WATTS Drainage representative for any clarification. Dimensions are subject to manufacturing tolerances.
© Watts Drainage 2003
CANADA
CANADA: 5435 North Service Road, Burlington, ON, L7L 5H7 TEL: 905-332-6718 TOLL-FREE: 1-888-208-8927 Website: www.wattsdrainage.ca
Order Code:CA-321-
Ex. CA-311-M51
Options (Select One or More)Suffix Description
Wall Thickness over 5", per add inch (single)
-M51
Wall Thickness over 12", per inch(Back to Back)
-M52
Vandal Proof Trim, Single-M53Floor to Ceiling Adaptor, Single-M59Valve Supporting Plate, Single-M60Valve Supporting Bar, Single-M61Flush Valve Piping Support, Single-M62
CA-311-OR
272
CANADA
1 7301793-100 Rev. B
Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.
Channel Lock PliersRegular Screwdriver
Recommended Tools & Materials
Rough-InDimensions
RECOMMENDED CARRIER
Phillips Screwdriver
Pipe Wrench
Drill
Plumbers' Putty or Caulking
Tubing Cutter
TapeMeasure
Hacksaw
Pencil
Torch
Level
SA
VE
F
OR
F
UT
UR
E
US
E
CAUTION: PRODUCT IS FRAGILE. TO AVOID DAMAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
ICU Sink SystemModels: 9118.111, 9118.100 & 9118.150
INSTALLATION INSTRUCTIONS
!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .© A S A m e r i c a , I n c . 2 01 2
14-3/4"(375mm)
17"(432mm)
4-3/4"(121mm)
5/8"(14mm)
1-5/8"(41mm)
20"(509mm)
4-3/4"(120mm)
8" (203mm)
1/2" DIA.(13mm)
FINISHED WALL
BASE MOUNTDETAIL
FINISHEDFLOOR
FINISHEDFLOOR
FINISHEDFLOOR
26-1/8"(663mm)
36"(914mm)
36-1/2"(927mm)
36-1/2"(927mm)
40-1/8"(1020mm)
2-3/4"(70mm)
9/16" DIA.(14mm)
2-3/4"(70mm)
4"(102mm)4"
(102mm)
JAY-RSMITH MFG. CO.SQ-0-4437 FLOOR MOUNTEDSINK SUPPORT
MOUNTINGSTUDS
Adjustable Wrench
*FAUCET PERCH2-1/2" DIA. (65mm)
*FAUCET PERCH2-1/2" DIA. (65mm)
*DISCLAIMER: Faucets with a base diameter greater than 2-1/4" (57 mm) will not fit on this ICU Sink. The Selectronic ICU Faucet was specifically designed to minimize splashing during operation. American Standard will not be liable for any splashing that occurs if faucets other than the American Standard ICU Faucets are used.
8"(203mm) BETWEENMOUNTING HOLES
2 37301793-100 Rev. B 7301793-100 Rev. B
4 5
6
INSTALL ICU SINK1. Mount SINK onto the two HANGER STUDS. Hold SINK in place and temporarily install NYLOCK NUT & WASHER on one of the HANGER STUDS to retain SINK.
MOUNT ELECTRONICS BOX COMPLETE WASTE OUTLET CONNECTIONNOTE: Installation with ELECTRONIC BOX only is for cold or tempered water. Use optional MIXING VALVE with ELECTRONIC BOX when Hot and Cold supplies are roughed-in. See illustration below.
8
INSTALL ELECTRONICS HANGER BRACKET
1. Install the ELECTRONICS HANGER BRACKET onto remaining HANGER STUD. Install NYLOCK NUT & WASHER but do not tighten fully.
2. Remove NYLOCK NUT & WASHER from first HANGER STUD and install other end of ELECTRONICS HANGER BRACKET. Replace NYLOCK NUT & WASHER, tighten both ends. Do not over tighten, chinaware could become damaged.
NYLOCK NUTAND WASHER
HANGER STUD
COLD WATER ORTEMPERED WATER(3/8" SUPPLY)
HOT
MIXING VALVE
MIXING VALVE
SCREWS
MOUNTING PLATE
ELECTRONICBOX
ELECTRONIC BOX
COLD
1
2
1. Connect SUPPLY NUT (1) from SPOUT assembly to nipple on top of ENCLOSURE (2). Tighten with adjustable wrench to make a water tight connection.
CONNECT SPOUT HOSE TO ENCLOSURE
ELECTRONICBOX
1. Install “P” TRAP. Connect OFFSET TAILPIECE to “P” TRAP. TAILPIECE may have to be cut to fit installation. Use tubing cutter to cut TAILPIECE.
P-TRAP
TAILPIECE
1-1/4" OD
1-1/4" or 1-1/2" ODWASTE OUTLET
ELECTRONICSHANGER BRACKET
7
1. Remove COVER from ELECTRONICS BOX.
2. Place ELECTRONICS BOX onto MOUNTING PLATE. Align BOX with mounting holes. Attach with SCREWS provided.
3. Hang MOUNTING PLATE with ELECTRICAL BOX on HANGER BRACKET.
NOTE: For ease of installation and accessibility, it isrecommended that straight stops with flex supply tubes beused. As an alternative, if rigid supply risers are used, it issuggested to use angle stops in place of the straight stops.
NOTE: For more detailed information, see the installationinstructions supplied with the ICU FAUCET. #(M965119)
3
21
36-1/2"(927mm)
18"(457mm)
SQ-0-4437 FLOORMOUNTED SINKSUPPORT
1-5/8"(41mm)
FINISHED WALL
MOUNTINGSTUDS
8" (203mm)
FINISHEDFLOOR
INSTALL FAUCETROUGH-IN SUPPLIES AND WASTE OUTLET
INSTALL GRID DRAIN AND OFFSET TAILPIECE
1. Insert WIRES (1), FLEX HOSE (2) and SPOUT SHANK (3) through center hole of mounting surface.
2. Assemble "C" WASHER (4), STAR WASHER (5) and LOCKNUT (6) onto threads of SPOUT SHANK (3) from underside of mounting surface.
3. Align FAUCET and tighten LOCKNUT (6).
1. Apply plumber’s putty to the underside of flange. Install GRID DRAIN into drain outlet. 2. From the underside of SINK install RUBBER GASKET (flat side up) and FRICTION GASKET onto GRID DRAIN threads. Apply sealent to threads of GRID DRAIN. 3. Apply sealent to threads of OFFSET TAILPIECE and thread into DRAIN ELL.
4. Thread DRAIN ELL onto GRID DRAIN, tighten and align as shown.
1. Rough-in 3/8" supplies and waste outlet connections.
1
2 3 4
5
6
6
5
4
3
3/8" (10mm)SUPPLIES
4"(102mm)
*1-1/4" (32mm)OR 1-1/2" (38mm)WASTE OUTLET
*CHECK LOCAL CODES
PLUMBER’SPUTTY
RUBBERGASKET
FRICTIONGASKET
APPLYSEALANT
APPLY SEALANTTO THREADS
DRAIN ELL
OFFSET TAILPIECE
DRAIN ELL
GRID DRAIN
GRID DRAIN
1 2
3
4
4 57301793-100 Rev. B 7301793-100 Rev. B
WIRE HANGER EYEBOLT
REMOVE THUMB NUTFROM EYE BOLT
4. WIRE HANGER is positioned behind ELECTRONIC BOX and in front of DRAIN.
5. Remove THUMB NUT from EYEBOLT.
13
15
CHECK ALL ELECTRICAL ANDPLUMBING CONNECTIONS
14 TEST INSTALLED FAUCET
INSTALL WIRE HANGER
1.Turn on water supplies and check for leaks. Tighten any connections if necessary.
2. Check FAUCET operation, if adjustment is required refer to the installation instructions shown at right supplied with the ICU FAUCET. No. M965119.
1. Install EYEBOLT onto WIRE HANGER if not installed.
2. Place WIRE end in left SIDE HOLE.
3. Place WIRE end in right SIDE HOLE near DRAIN.
NOTE: If not enough tension, remove WIRE and spread ends approx. 1" additional and re-attach.
6. EYEBOLT for SINK APRON.
No. M965119 Ins
tall
ati
on
In
str
uc
tio
ns
(In Toronto Area only: 1-905-3061093)
SELECTRONIC™Proximity ICU Faucet
Certified to comply with ASME A112.18.1M
© 2011 American Standard
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.customer's e-mail us at: [email protected] Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
M965119
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
6055.1936056.193
MODEL NUMBERS
6055 / 6056 ICU Faucet shown Installed onAmerican Standard 9118.111 ICU Sink
WIRE
WIRE
WIRE HANGER
EYEBOLT
TO ENSURE A LAMINAR WATER FLOW the air must be slowly purged from the spout. To do so, cover the SENSOR (1) while slowly opening the water supply valves. When the water flows as a solid, smooth, steady stream, uncover the SENSOR (1) and fully open the water supply valve.
DETECTION
ZONE
1
INSTALL AND CONNECT MIXING VALVE(MIXING VALVE IS OPTIONAL)
CONNECT MIXING VALVE TO WATER SUPPLIES
11
10
12
ELECTRICAL HOOK-UP AND INSTALLATION
COLD WATEROR TEMPEREDWALL SUPPLY
ELECTRONICBOX
12 4
33
Ins
tall
ati
on
In
str
uc
tio
ns
(In Toronto Area only: 1-905-3061093)
SELECTRONIC™Proximity ICU Faucet
Certified to comply with ASME A112.18.1M
© 2011 American Standard
To learn more about American Standard Faucets visit our website at: www.americanstandard.comor U.S. customer's e-mail us at: [email protected] Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-306-1093)
M965119
Product No.'s & Options
Specifications
How to Install
Electrical Hook-up
Maintenance
FAQ,s
Replacement Parts
1
2
2-3
4-6
7-8
9
10
6055.1936056.193
MODEL NUMBERS
6055 / 6056 ICU Faucet shown Installed onAmerican Standard 9118.111 ICU Sink
1. Insert FIBER WASHER (4) into SUPPLY NUT (1) on ENCLOSURE (2).
2. Connect SUPPLY NUT (1) on ENCLOSURE (2) to FLEXIBLE SUPPLY HOSE (3). Tighten to make a water tight connection. Use two wrenches to tighten if necessary.
3. Connect FLEXIBLE SUPPLY (3) directly to wall supply. Connection on FLEXIBLE SUPPLY (3) is 3/8" compression. Use adjustable wrench to tighten connection. Do not over tighten.
Note: FLEXIBLE SUPPLY (3) measures 20" from the bottom of the ENCLOSURE (1) base. If additional supply length is required, installer must purchase parts separately. Important: If FLEXIBLE SUPPLY (3) is too long, loop to avoid kinking.
9 CONNECT WATER SUPPLY TO ENCLOSUREAND TO COLD OR TEMPERED WALL SUPPLY
1. Remove COVER from MIXING VALVE.
2. Install FIBER SEAL WASHER (4) on MIXING VALVENIPPLE (3). Hold MIXING VALVE (1) in place with one hand and with your other hand thread SWIVEL NUT (2) onto MIXING VALVE NIPPLE (3). Use an adjustable wrench to tighten SWIVEL NUT (2).
3. Place MIXING VALVE BOX onto MOUNTING PLATE. Align BOX with mounting holes. Attach with SCREWS provided. 4. Replace COVER and tighten securely.
NOTE: For complete detailed installation and operating instructions see installations instructions supplied with mixing valve. No. M968808
For complete detailed installation and operating instructions see installations instructions supplied with ICU FAUCET. No. M965119
1
2
1 2
3
42
ADJUSTABLE WRENCH
HOT
MIXING VALVEELECTRONIC
BOX
COLD
1. Turn off Hot and Cold water supplies before beginning.
2. Connect FLEXIBLE SUPPLIES directly to wall supplies. Connections on MIXER supplies are 3/8" compression. Connect left supply to Hot and right supply to Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.
3. Faucet supplies measure 20" from the bottom of the ENCLOSURE (3) base.
Note: If additional supply length is required, installer must purchase parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop as to avoid kinking.
Ins
tall
ati
on
In
str
uc
tio
ns
(In Toronto Area only: 1-905-3061093)
SELECTRONIC™Thermostatic Mixing Valve
Certified to comply with ASME A112.18.1M
© 2005 American Standard
M968808
To learn more about American Standard Faucets visit our website at: www.us.amstd.com or U.S.customer's e-mail us at: [email protected] Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
NOTE TO INSTALLER: Please give this manual to the customer after installation.
(In Toronto Area only: 1-905-3061093)
605XTMV
Speci�cations
Installation
Adjust Temperature
Service
Replacement Parts
1
2
3
3
4
No. M968808
No. M965119
6 77301793-100 Rev. B 7301793-100 Rev. B
Repair PartsICU Sink SystemModels: 9118.111,
9118.100 & 9118.150
7381259-401.0200AICU Sink Shroud Kit
7381243-251.0020AO�set Drain
7381242-0500AP-Trap Assembly
7381266-200.0070ABracket Assembly
16 INSTALL SINK APRON
1. Hold APRON up against SINK and flush against finished wall.
2. Mark a line with a pencil on the wall about 6" long as shown on both sides of the APRON..
3. Remove the APRON. Clean the wall where the APRON BRACKETS supplied with SINK are to be applied. Peel off the protective strip from the back of the APRON BRACKETS. Apply the two APRON BRACKETS to the finished wall parallel to the pencil marks as shown in the illustration below.
OPTIONAL MOUNTING. (SCREWS AND ANCHORS NOT SUPPLIED) Use Brackets to mark pilot holes on wall. Drill holes for ANCHORS. Peel off the protective strip from the back of the APRON BRACKETS. Apply the two APRON BRACKETS to the finished wall parallel to the pencil marks as shown and aligned with the mounting holes. See illustration below. Install SCREWS and tighten.
4. Clean off the pencil marks from wall.
6"(152mm)
APRON
SINK
6. Retain APRON with THUMB NUT. Finger tight only.5. Position APRON under SINK and against finished wall alinging EYEBOLT with hole in APRON.
THUMB NUT
EYEBOLT
APRON
APRON
IMPORTANT: SAVE ALL INSTALLATION INSTRUCTIONS FOR FUTURE USE
1/2"(13mm)
PENCIL MARK
APRON
CLEAN WALL
PROTECTIVESTRIP
87301793-100 Rev. B
THIS WARRANTY IS NOT TRANSFERABLE FROM ORIGINAL CONSUMER PURCHASER.
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
If inspection of this AS America, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof of purchase will be required—save sales receipt.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation.
This limited warranty is void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.
American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal or installation. IN NO EVENT WILL AMERICAN STANDARD BE LIABLE FOR THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION MATERIALS, INCLUDING BUT NOT LIMITED TO, TILES, MARBLE, ETC. American Standard will not be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this limited warranty. This limited warranty does not cover any liability for consequential or incidental damages, all of which are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including those of merchantability or fitness for an intended purpose. (Some states or provinces do not allow the exclusion or limitation of implied limited warranties, so this exclusion may not apply to you.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this limited warranty does not affect such statutory rights.
In the United States:American Standard Brands
P.O. Box 6820Piscataway, New Jersey 08855
Attention: Director of Customer CareFor residents of the United States, warranty information may also be obtained by calling
the following toll free number: (800) 442-1902www.americanstandard.com
In Canada:AS Canada, ULC
5900 Avebury Rd. Mississauga, Ontario
Canada L5R 3M3Toll Free: (800) 387-0369www.americanstandard.ca
In Mexico:American Standard B&K Mexico
S. de R.L. de C.V.Via Morelos #330Col. Santa Clara
Ecatepec 55540 Edo. MexicoToll Free: 01-800-839-1200
www.americanstandard.com.mx
Kind
red
Com
mer
cial
Prin
ted
inCa
nada
PROJECT INFORMATION
Project Name:
Item Reference:
Location:
Quote #:
Faucet Model #:
Drillings Required:
Notes:Kind
red
Com
mer
cial
Prin
ted
inCa
nada
21561562 0311
Franke Kindred Canada Limited1000 Franke Kindred Road, Midland, Ontario, Canada L4R 4K9web www.kindred-commercial.com email [email protected] 1-866-687-7465 Fax 1-800-361-8408
HWS1420P-00Wash Basins & Troughs
Specification:18 gauge, type 304, 18-10 stainless steel medical hand wash basin.Polished to a #4 satin finish. Fixture bowl is constructed with radius covedcorners. Integral side splashes help prevent splashing and contamination ofnearby surfaces. Waste location left rear.
This fixture is coated with SANIGUARD® product protection.SANIGUARD® product protection is applied to all exposed surfaces of thesink. This treatment utilizes a silver ion technology to inhibit the growth ofbacteria, molds and mildews. Silver ions are only released in the presenceof bacteria-laden moisture and disrupt the metabolic and reproductivecycles of the micro-organisms.
Compartment Size: 14" x 20" x 10" (35cm x 51cm x 25cm)
Overall Size: 18 3/4" x 21" x 37" (48cm x 53cm x 94cm)
Backsplash: 26 1/2" (67cm)
Notes:• Separate sink carrier is not required• Electronic specifications, reference www.kindred-commercial.com• SANIGUARD® product protection is designed to protect the product
itself and will not protect the user or others from food-borne illness ordisease. Always follow proper hygienic and cleaning procedures whenusing this product.
18 3/4” [48cm]
37”[94cm]
26 1/2”[67cm]
10”[25cm]
21” [53cm]
Integrally welded 1.5"tailpiece
3”[8 cm]
4 1/2”[11 cm]
14”[36 cm]
Complies with:
CSA Z8000 Standard
CHICA Positioning Statement
HAND HYGIENE SINKMODEL IC07DM
Material
• DuPont™ Corian®
• Non-porous
• Renewable
• Easy to Clean with h o s p i t a l a p p r o v e d c l e a n e r s a n d disinfectants
Infection Control Features
• Deep bowl sufficient to prevent recontamination
• Drain is offset from faucet to minimize splashing
• Thin rim sloped back to bowl
• Faucet deck sloped back to bowl
• Integrated coved backsplash
• Solid underside
Dimensions
• 9” Deep Bowl
• Bowl & Backsplash
23.5”Wx22”Hx18”D
• 18” high backsplash
• Plumbing Shroud
7.5”Wx11”Hx9”D
Additional Features
• Steel bracket for easy installation
• Custom sizes available for backsplash
• Wall mount faucet model also available
• Easily removable plumbing hardware shroud
Manufacturer:
RJW Enterprises Inc.
Specializing in Healthcare sinks since 1995
Ontario, Canada
1-888-279-7841 [email protected]