handbook of lubricants
TRANSCRIPT
S H E L L C A N A D A
Lubricants Handbook 2002
This handbook provides technical information about Shelllubricants and their applications. Information contained in thishandbook is current at the time of publication. Manufacturer’sspecifications and Shell’s product data may change at any time.
We wish to thank the many contributors to this handbook fortheir input and their interest in keeping lubrication informationup to date and as accurate as possible. Our commitments toquality, service and caring enough to make a difference areshared with every user of this manual.
Shell Canada Products also publish “Lubricants Report” technicaldata sheets which may contain more information than has beenincluded in this handbook. The identifying number of the mostrecent Lubricants Report is given after the product name anddescriptor (in the top right corner of the page) for each productentered in this book. For this information and/or furtherapplication information, which may not be contained in thishandbook, we invite you to contact Shell at:
The Shell Helps Centre1-800-661-1600Facsimile (403) 691-3997
InternetShell Canada Homepage: www.shell.ca
E-Mail: [email protected]
For Material Safety Data Sheets (MSDS)Phone (403) 691-2615Facsimile (403) 691-3321
INTRODUCTION
1.1
Shell Lubricants Handbook INTR
OD
UCTIO
N
1.2
INTRODUCTION
1.3
Table of Contents
Page
IntroductionTrademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4ISO Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5Shell Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.6Health, Safety and Sustainable Development. . . . . . . . . 1.7
Product Application Guide . . . . . . . . . . . . . . . 2.1 - 2.7
Automotive Lubricants . . . . . . . . . . . . . . . . . . . 3.1 - 3.29
Aviation Lubricants - AEROSHELL . . . . . . . . . . 4.1 - 4.8
Food Grade Lubricants . . . . . . . . . . . . . . . . . . . 5.1
Greases. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 - 6.33
Industrial Oils . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 - 7.62
Marine and Rail Lubricants . . . . . . . . . . . . . . . 8.1 - 8.8
Process Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 - 9.5
Specialty Lubricants . . . . . . . . . . . . . . . . . . . . . 10.1 - 10.18
Synthetic Lubricants . . . . . . . . . . . . . . . . . . . . . 11.1
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.1 - 12.26
Product Index (Alphabetical by Name) . . . . . 13.1 - 13.3
™ TRADEMARK OF SHELL CANADA LIMITED
ADVANCE SNOW ULTRA,AEROSHELL,ALBIDA,ALEXIA,ALVANIA,ARGINA, CAPRINUS, CARDURA, CASSIDA, CASSIS, CLASSLUBE,CLAVUS, CORENA, CYPRINA, DARINA, DECOL, DELIMA,DENTAX, DIALA, DONAX, DOLIUM, DROMUS, DURSOL,FormulaShell, GADINIA, GARIA, GEARTHERM, MALLEUS,MELINA, MICROGEL, MICROLITH, MORLINA, MYSELLA,NAUTILUS, OMALA, PELLA, RETINAX, ROTELLA, ROTELLA T,ROTELLA ELC, SHELLFLEX, SHELLZONE, SHELL ADVANCE,SHELL FLEET, SHELL INDUSOL, SHELL NATURELLE,SHELL TURBO, SIRIUS, SPIRAX, SRS 2000, STRINGOL, SURSTAY,TELLUS,THERMIA,TIVELA,TONNA,TORCULA, ULTRAGEL,VALVATA,VITREA,VSI, XLA, XTC-50
are trademarks of Shell Canada Limited. Used under license byShell Canada Products.
HYPERIA and OSSAGOL are trademarks of Shell InternationalPetroleum Company. Used under license by Shell CanadaProducts.
In this handbook ‘*’ indicates Trademarks of the followingcompanies:
Dexron is a registered trademark of General Motors Corporation
Freon is a registered trademark of The DuPont Company
Mercon is a registered trademark of Ford Motor Company
Mylar is a registered trademark of The DuPont Company
Neoprene is a registered trademark of The DuPont Company
RAVE is a registered trademark of Bombardier Inc.
Teflon is a registered trademark of The DuPont Company
TC-WII and TC-W3 are registered trademarks of National MarineManufacturers Association
Viton is a registered trademark of DuPont Canada Inc.
INTRODUCTION
1.4
Trademarks
INTRODUCTION
1.5
Shell Guarantee
Shell LubricantsISO 9001 Certified
ISO 9001 is the most comprehensive of the
ISO standards. It requires companies to design,
implement, and maintain quality control processes
throughout their business activities.
Shell Lubricants has been accredited under
ISO 9001 for its manufacturing facilities.
Every manufacturing process that affects
satisfaction of Lubricants customers and
their needs is regularly audited.
Continuous monitoring and improvement are
assured through a series of detailed processes,
the ISO requirements, and by third party audits.
INTRODUCTION
1.6
Shell Guarantee
The Shell Guarantee
We believe Shell lubricants are the
very best available, and we back these
with a no compromise Guarantee:
Shell will restore any piece of equipment to
full specification performance when damaged
due to the failure of our lubricants.
We will guarantee the performance of
our lubricants when used in accordance with
Shell’s recommendations and manufacturer’s
requirements and specifications.
This warranty applies to all original
manufacturer’s equipment.
The Shell guarantee is in addition to
the OEM’s own warranty, and does
not alter nor invalidate it.
In Shell Canada we are committed to:
• pursue the goal of no harm to people,
• protect the environment and pursue the goal ofprevention of pollution,
• use material and energy efficiently to provide ourproducts and services,
• develop energy resources, products and servicesconsistent with these aims,
• publicly report on our performance and engage in stakeholder consultation,
• play a leading role in promoting best practice in our industry,
• manage health, safety and sustainable development as any other critical business activity, and
• promote a culture in which all Shell employees share this commitment.
In this way we strive to achieve a health, safety and sustainabledevelopment performance that we are proud of, to earn theconfidence of customers, shareholders and society at large and tobe a good neighbor. We contribute to sustainable developmentthrough the integration of environmental, social and economicconsiderations in our decision-making process.
INTRODUCTION
1.7
Health, Safety and Sustainable Development
APPLICATION PRODUCT PAGE
Airline Oilers Tellus 22 . . . . . . . . . . . . . . . . . . . . 7.46Torcula . . . . . . . . . . . . . . . . . . . . . 7.56
Allison C-4 Fluids Donax TC . . . . . . . . . . . . . . . . . . . 3.6Donax TD . . . . . . . . . . . . . . . . . . . 3.8Donax TG . . . . . . . . . . . . . . . . . . . 3.10Rotella T (All) . . . . . . . . . . . . 3.18 - 3.25
Antifreeze / Coolant Shellzone . . . . . . . . . . . . . . . . . . . 3.4Rotella ELC Coolant. . . . . . . . . . . . 3.5
Automatic Transmission Fluid
Dexron IIIG/Mercon Donax TG . . . . . . . . . . . . . . . . . . . 3.10Type F Donax TF . . . . . . . . . . . . . . . . . . . 3.9
Aviation LubricantsEngine Oils - Piston AeroShell Oils . . . . . . . . . . . . . . . . 4.3
AeroShell Oil W. . . . . . . . . . . . . . . 4.4AeroShell Oil W 15W-50 . . . . . . . . 4.5AeroShell Oil W 100 Plus. . . . . . . . 4.6
Engine Oils - Turbine AeroShell Turbine Oils . . . . . . . . . . 4.8Greases AeroShell Greases . . . . . . . . . . . . . 6.6Fluids AeroShell Fluids . . . . . . . . . . . . . . 4.7
Ball Mills Malleus GL . . . . . . . . . . . . . . . . . . 6.24
BiodegradableBilge Cleaner Nautilus Biodegr. Bilge Cleaner . . . 10.13Boat Cleaner Nautilus Biodegr. Boat Cleaner . . . 10.14Hydraulic Shell Naturelle HF-M . . . . . . . . . . . 7.33
Shell Naturelle HF-E. . . . . . . . . . . . 7.322 Stroke Engine Oils Nautilus Biogradable Outboard
Motor Oil . . . . . . . . . . . . . . . . . . 10.9
Caterpillar FD-1 Fluids Donax CFD 60 . . . . . . . . . . . . . . . 3.11
Caterpillar TO-4 Fluids Donax TC . . . . . . . . . . . . . . . . . . . 3.6
Chainsaw LubricantsBar and Chain Chain Oils . . . . . . . . . . . . . . . . . . . 10.72 Cycle Engines XTC-50 . . . . . . . . . . . . . . . . . . . . . 10.18
Circulating Oils Corena S . . . . . . . . . . . . . . . . . . . . 7.18Decol H. . . . . . . . . . . . . . . . . . . . . 7.19Morlina . . . . . . . . . . . . . . . . . . . . . 7.30Tellus . . . . . . . . . . . . . . . . . . . . . . 7.46Shell Turbo T . . . . . . . . . . . . . . . . . 7.58VSI 68 . . . . . . . . . . . . . . . . . . . . . . 7.62
Compressor OilsAir - Recip Corena P . . . . . . . . . . . . . . . . . . . . 7.16
Corena DE (Synthetic). . . . . . . . . . 7.12
PRODUCT APPLICATION GUIDE
2.1
APPLIC
ATIO
N G
UID
E
PRODUCT APPLICATION GUIDE
2.2
APPLICATION PRODUCT PAGE
Compressor Oils (continued)
Air - Dry Screw Tellus . . . . . . . . . . . . . . . . . . . . . . 7.46Decol H. . . . . . . . . . . . . . . . . . . . . 7.19Donax TG . . . . . . . . . . . . . . . . . . . 3.10
Air - Flooded Screw Donax TG . . . . . . . . . . . . . . . . . . . 3.10Corena AS (Synthetic) . . . . . . . . . . 7.10Tellus . . . . . . . . . . . . . . . . . . . . . . 7.46Corena S . . . . . . . . . . . . . . . . . . . . 7.18
Air - Vane Corena AS (Synthetic) . . . . . . . . . . 7.10Corena S . . . . . . . . . . . . . . . . . . . . 7.18
Natural Gas/Propane(cylinders & packings only) Corena NG . . . . . . . . . . . . . . . . . . 7.14
Refrigeration Ammonia, CFC (Freons) Clavus . . . . . . . . . . . . . . . . . . . . . . 7.6Ammonia,
CFC (Freons), HCFC Clavus AB (Synthetic) . . . . . . . . . . 7.7HFC (R134A),
CFC (Freons) & blends Clavus HFC 68 (Synthetic). . . . . . . 7.8
Concrete Form Oil Form Oil 46. . . . . . . . . . . . . . . . . . 7.25
Cutting Oils See Metal Working Fluids
Cylinder Oils (Steam) Valvata . . . . . . . . . . . . . . . . . . . . . 7.60
Drilling Lubricants Malleus TC. . . . . . . . . . . . . . . . . . . 6.26Diamond Drill Rod . . . . . . . . . . . . 6.22
Electrical Insulating Oil Diala A . . . . . . . . . . . . . . . . . . . . . 7.22Diala AX . . . . . . . . . . . . . . . . . . . . 7.22
Engine OilsAviation AeroShell Oils (piston) . . . . . . 4.3
AeroShell Oil W (piston) . . . . . 4.4, 4.5AeroShell Oil W 100 Plus. . . . . 4.6AeroShell (turbine) . . . . . . . . . . . . 4.8
Diesel Rotella T Single Grade . . . . . . . . . . 3.18Rotella T with XLA (Multigrade) . . 3.20Rotella T SB . . . . . . . . . . . . . . . . . . 3.22Rotella T Plus. . . . . . . . . . . . . . . . . 3.24Shell Fleet . . . . . . . . . . . . . . . . . . . 3.16
Gasoline FormulaShell (mineral) . . . . . . . . . 3.12FormulaShell (synthetic blend) . . . 3.12FormulaShell (synthetic) . . . . . . . . 3.14FormulaShell SAE 30 & SAE 40 . . . 3.15
Gasoline - 2 Stroke See 2 Stroke Engine OilGasoline - 4 Stroke See Outboard Engine OilsLocomotive (Diesel) Caprinus . . . . . . . . . . . . . . . . . . . . 8.4Marine (Diesel) Alexia Oil 50 . . . . . . . . . . . . . . . . . 8.2
Argina . . . . . . . . . . . . . . . . . . . . . . 8.3Gadinia . . . . . . . . . . . . . . . . . . . . . 8.6Melina . . . . . . . . . . . . . . . . . . . . . . 8.7Sirius FB 30 . . . . . . . . . . . . . . . . . . 8.8
PRODUCT APPLICATION GUIDE
2.3
APPLICATION PRODUCT PAGE
Engine Oils (continued)Natural Gas Mysella . . . . . . . . . . . . . . . . . . . . . 7.31Railway (Diesel) Caprinus . . . . . . . . . . . . . . . . . . . . 8.4
Flushing Oil Cassis A . . . . . . . . . . . . . . . . . . . . . 7.4
Food Grade LubricantsOils Shell Fluid FM 32. . . . . . . . . . . . . . 7.3Greases Shell FM Grease 1.5. . . . . . . . . . . . 6.16
Form OilsConcrete Form Oil 46. . . . . . . . . . . . . . . . . . 7.25
Gear OilsAutomotive Dentax . . . . . . . . . . . . . . . . . . . . . 3.26
Dentax S . . . . . . . . . . . . . . . . . . . . 3.29Spirax HD . . . . . . . . . . . . . . . . . . . 3.26Spirax S. . . . . . . . . . . . . . . . . . . . . 3.28
Industrial - Enclosed Geartherm. . . . . . . . . . . . . . . . . . . 7.27Hyperia S (synthetic). . . . . . . . . . . 7.28Omala . . . . . . . . . . . . . . . . . . . . . . 7.38Omala HD (synthetic) . . . . . . . . . . 7.40Omala RL (synthetic). . . . . . . . . . . 7.41Tellus (non EP) . . . . . . . . . . . . . . . 7.46
Industrial Enclosed (with Back stops) Morlina . . . . . . . . . . . . . . . . . . . . . 7.30Industrial - Open Malleus GL . . . . . . . . . . . . . . . . . . 6.24Specialty Nautilus Marine Gear Oil . . . . . . . . 10.12
Nautilus Synthetic Gear Oil . . . . . . 10.16Worm - Compounded Valvata . . . . . . . . . . . . . . . . . . . . . 7.60Worm - Synthetic Omala RL . . . . . . . . . . . . . . . . . . . 7.41
Tivela . . . . . . . . . . . . . . . . . . . . . . 7.53
GreaseAviation Grease AeroShell Grease . . . . . . . . . . . . . . 6.4Automotive Chassis Darina AX . . . . . . . . . . . . . . . . . . . 6.18
Darina XL . . . . . . . . . . . . . . . . . . . 6.20Albida LC . . . . . . . . . . . . . . . . . . . 6.8SRS 2000 . . . . . . . . . . . . . . . . . . . . 6.30
Drill Rod Diamond Drill Rod . . . . . . . . . . . . 6.22Electric Motors Cyprina RA . . . . . . . . . . . . . . . . . . 6.17
Alvania 2 . . . . . . . . . . . . . . . . . . . . 6.14Enclosed Gear Boxes Malleus GL . . . . . . . . . . . . . . . . . . 6.24
Surstay 000 . . . . . . . . . . . . . . . . . . 6.32Retinax TL 00 . . . . . . . . . . . . . . . . 6.28
Fifth Wheel Darina XL 102 Moly . . . . . . . . . . . 6.20SRS Moly . . . . . . . . . . . . . . . . . . . . 6.30
Food Grade Shell FM Grease 1.5. . . . . . . . . . . . 6.16Extreme High Temperature Ultragel . . . . . . . . . . . . . . . . . . . . . 6.33
APPLICATION PRODUCT PAGE
Grease (continued)Moly Alvania EP . . . . . . . . . . . . . . . . . . . 6.12
Darina 102M . . . . . . . . . . . . . . . . . 6.20Darina XL EP2 Moly. . . . . . . . . . . . 6.20Ossagol C Moly . . . . . . . . . . . . . . . 6.27SRS 2000 . . . . . . . . . . . . . . . . . . . . 6.30Advance Snow Ultra . . . . . . . . . . . 6.4
Multi-Purpose Albida LC . . . . . . . . . . . . . . . . . . . 6.8Alvania EP . . . . . . . . . . . . . . . . . . . 6.12Darina XL . . . . . . . . . . . . . . . . . . . 6.20SRS 2000 . . . . . . . . . . . . . . . . . . . . 6.30
Natural Gas Valves Dursol K1 . . . . . . . . . . . . . . . . . . . 6.23Open Gear Malleus GL . . . . . . . . . . . . . . . . . . 6.24Outdoor Mobile Darina XL 102 Moly. . . . . . . . . . . . 6.20
Alvania MS . . . . . . . . . . . . . . . . . . 6.12Darina XL MS . . . . . . . . . . . . . . . . 6.20SRS Winter . . . . . . . . . . . . . . . . . . 6.30
Railway Journal Roller Bearing Alvania EP D . . . . . . . . . . . . . . . . . 6.10
Railway Traction Motors Cyprina RA . . . . . . . . . . . . . . . . . . 6.17Rail Lubricant Ossagol C Moly . . . . . . . . . . . . . . . 6.27
Cardura . . . . . . . . . . . . . . . . . . . . . 6.15Semi-Fluid Ossagol C Moly . . . . . . . . . . . . . . . 6.27
Surstay EP 000. . . . . . . . . . . . . . . . 6.32Retinax TL 00 . . . . . . . . . . . . . . . . 6.28
Steel Mill Albida LC . . . . . . . . . . . . . . . . . . . 6.8Alvania EP . . . . . . . . . . . . . . . . . . . 6.12
Synthetic Darina XL 102 . . . . . . . . . . . . . . . . 6.20Advance Snow Ultra Grease. . . . . . 6.4Retinax TL 00 . . . . . . . . . . . . . . . . 6.28SRS 2000 (Partial Syn.) . . . . . . . . . 6.30AeroShell Greases 7, 22 and 33 . . . 6.6
Thread Compound Malleus TC. . . . . . . . . . . . . . . . . . . 6.26Water Resistant SRS 2000 (Partial Syn.) . . . . . . . . . 6.30Wheel Bearing Albida LC . . . . . . . . . . . . . . . . . . . 6.8
Darina XL EP2 . . . . . . . . . . . . . . . . 6.20
Heat Transfer Oil Thermia C . . . . . . . . . . . . . . . . . . . 7.52
Hydraulic OilsAll Weather Tellus T . . . . . . . . . . . . . . . . . . . . . 7.50
Tellus HD (Synthetic) . . . . . . . . . . 7.48Biodegradable Shell Naturelle HF-E. . . . . . . . . . . . 7.32
Shell Naturelle HF-M . . . . . . . . . . . 7.33Cold Temperature Tellus HD . . . . . . . . . . . . . . . . . . . 7.48
AeroShell Fluid 4 . . . . . . . . . . . . . 4.7Fire Resistant No Fire (WG 200R) . . . . . . . . . . . . 7.36
PRODUCT APPLICATION GUIDE
2.4
PRODUCT APPLICATION GUIDE
2.5
APPLICATION PRODUCT PAGE
Hydraulic Oils (continued)Indoor Tellus . . . . . . . . . . . . . . . . . . . . . . 7.46
Decol H. . . . . . . . . . . . . . . . . . . . . 7.19Corena S (R&O) . . . . . . . . . . . . . . 7.18
Less Flammable Shell FR-N . . . . . . . . . . . . . . . . . . . 7.34
Lapping Oil Pella A . . . . . . . . . . . . . . . . . . . . . . 7.42
Locomotive Engine Oils See Engine Oils, Locomotive Diesel
Machine Tool Tonna V. . . . . . . . . . . . . . . . . . . . . . . 7.54
Marine LubricantsEngine Oils See Engine Oils, Marine DieselTurbines See Turbine Oils
Metal Working FluidsBroaching Garia D . . . . . . . . . . . . . . . . . . . . . 7.26
Garia T . . . . . . . . . . . . . . . . . . . . . 7.26Cutting Oil (Neat) Garia D . . . . . . . . . . . . . . . . . . . . . 7.26
Garia T . . . . . . . . . . . . . . . . . . . . . 7.26Grinding Garia D . . . . . . . . . . . . . . . . . . . . . 7.26Lapping Pella A . . . . . . . . . . . . . . . . . . . . . . 7.42Quenching Dromus B . . . . . . . . . . . . . . . . . . . 7.24Rolling Pella A . . . . . . . . . . . . . . . . . . . . . 7.42Soluble Cutting Oil Dromus B . . . . . . . . . . . . . . . . . . . 7.24Tapping & Threading Garia D . . . . . . . . . . . . . . . . . . . . . 7.26
Mineral Oils Pella A . . . . . . . . . . . . . . . . . . . . . . 7.42Shellflex . . . . . . . . . . . . . . . . . 9.2 - 9.5Vitrea . . . . . . . . . . . . . . . . . . . . . . 7.61
Non Drip Oils Chain Oils . . . . . . . . . . . . . . . . . . . 10.4Stringol . . . . . . . . . . . . . . . . . . . . . 7.44Tonna V. . . . . . . . . . . . . . . . . . . . . 7.54Torcula . . . . . . . . . . . . . . . . . . . . . 7.56
Natural GasCompressor Oils See Compressor Oils, Natural GasEngine Oils See Engine Oils, Natural Gas
Open Gear Lubricants Malleus GL . . . . . . . . . . . . . . . . . . 6.24
Outboard Engine Oils Nautilus Premium Outboard Motor Oil . . . . . . . . . . . . . . . . . . 10.8
Nautilus Biodegr. Outboard Motor Oil . . . . . . . . . . . . . . . . . . 10.9
Nautilus 4 Stroke Engine Oil . . . . . 10.10Nautilus Personal Watercraft Oil (synthetic) . . . . . . 10.17
Paper Machine Delima . . . . . . . . . . . . . . . . . . . . 7.20Delima R . . . . . . . . . . . . . . . . . . . 7.21
Plunger Pump Packing Oil Torcula . . . . . . . . . . . . . . . . . . . . 7.56
APPLICATION PRODUCT PAGE
Pneumatic Oil See Airline OilersPower Saw Lubricants
Bar and Chain Chain Oils . . . . . . . . . . . . . . . . . . 10.7Engine XTC-50 . . . . . . . . . . . . . . . . . . . . 10.18
Process Oils Shellflex . . . . . . . . . . . . . . . . . . 9.2, 9.4
Pump Oils Nautilus Jet Pump Oil . . . . . . . . . 10.15
Quenching Oils See Metal Working Fluids
Railway LubricantsJournal Roller
Bearing Grease Alvania EP D . . . . . . . . . . . . . . . . 6.10
Rail Lubricant Cardura . . . . . . . . . . . . . . . . . . . 6.15Ossagol C Moly . . . . . . . . . . . . . . 6.27
Traction Motor Grease Cyprina RA . . . . . . . . . . . . . . . . . 6.17
Engine Oils See Engine Oils - Locomotive (Diesel)
Refrigeration Oils See Compressor Oils, Refrigeration
Rockdrill Oil Torcula . . . . . . . . . . . . . . . . . . . . 7.56
Rust Inhibitors VSI 68 . . . . . . . . . . . . . . . . . . . . . 7.62
Saw Guide Oil Sawguide Oil . . . . . . . . . . . . . . . . 7.43Stringol . . . . . . . . . . . . . . . . . . . . 7.44Tonna V. . . . . . . . . . . . . . . . . . . . 7.54Torcula . . . . . . . . . . . . . . . . . . . . 7.56
Slide Way Lubricant Tonna V. . . . . . . . . . . . . . . . . . . . 7.54
Soluble Oil Dromus B . . . . . . . . . . . . . . . . . . 7.24
Solvents Shell Indusol . . . . . . . . . . . . . . . . 7.29
Spindle Oil Tellus 10 . . . . . . . . . . . . . . . . . . . 7.45
Snowmobile Lubricants Shell Advance Premium Snowmobile Oil . . . . . . . . . . . . 10.3
Advance Snow Ultra . . . . . . . . . . 10.4Advance Snow Ultra Grease . . . . 6.4Advance 100% Synthetic
Chain Case Oil . . . . . . . . . . . . . 10.6
Steam Cylinder Oil Valvata . . . . . . . . . . . . . . . . . . . . 7.60
Steam Turbine Oil Shell Turbo T . . . . . . . . . . . . . . . . 7.58
Synthetic LubricantsChain Case Oils Advance 100% Synthetic
Chain Case Oil . . . . . . . . . . . . . 10.6
Compressor Oils Clavus AB . . . . . . . . . . . . . . . . . . 7.7Clavus HFC 68 . . . . . . . . . . . . . . 7.8Corena AS . . . . . . . . . . . . . . . . . . 7.10Corena DE . . . . . . . . . . . . . . . . . 7.12Corena NG (Partial Syn) . . . . . . . 7.14
Engine Oils Advance Snow Ultra . . . . . . . . . . 10.4FormulaShell (Partial Syn) . . . . . . 3.12FormulaShell . . . . . . . . . . . . . . . 3.14
PRODUCT APPLICATION GUIDE
2.6
APPLICATION PRODUCT PAGE
Synthetic Lubricants Engine Oils (continued) Rotella T SB (Partial Syn) . . . . . . 3.22
Nautilus Personal Watercraft . . . . 10.17
Gear Oils Dentax S 50 . . . . . . . . . . . . . . . . 3.29Hyperia S 220 . . . . . . . . . . . . . . . 7.28Omala HD . . . . . . . . . . . . . . . . . 7.40Omala RL (non EP) . . . . . . . . . . . 7.41Spirax HD 75W-90 (Partial Syn) . 3.26Spirax S 75W-90 . . . . . . . . . . . . . 3.28Tivela . . . . . . . . . . . . . . . . . . . . . 7.53
Greases Advance Snow Ultra . . . . . . . . . . 10.4Darina XL 102 . . . . . . . . . . . . . . 6.20Retinax TL 00 . . . . . . . . . . . . . . . 6.28SRS 2000 (Partial Syn.) . . . . . . . . 6.30Ultragel . . . . . . . . . . . . . . . . . . . 6.33
Hydraulic Oils Tellus HD . . . . . . . . . . . . . . . . . . 7.48
Textile Oils Tellus 10 . . . . . . . . . . . . . . . . . . . . 7.45
Transformer Oil Diala A. . . . . . . . . . . . . . . . . . . . . 7.22Diala AX . . . . . . . . . . . . . . . . . . . 7.22
Transmission Fluids
Caterpillar TO-4 Donax TC . . . . . . . . . . . . . . . . . . 3.6
Dexron IIIG/Mercon Donax TG . . . . . . . . . . . . . . . . . . 3.10
Heavy Duty Dentax . . . . . . . . . . . . . . . . . . . . 3.26Dentax S . . . . . . . . . . . . . . . . . . . 3.29
Type F Donax TF . . . . . . . . . . . . . . . . . . 3.9
Universal Tractor Donax TD / TDL . . . . . . . . . . . . . 3.8
2 Stroke Engine Oils Shell Advance Premium Snowmobile Oil . . . . . . . . . . . . 10.3
Advance Snow Ultra . . . . . . . . . . 10.4Nautilus Premium Outboard
Motor Oil . . . . . . . . . . . . . . . . . 10.8Nautilus Biodegradable
Outboard Motor Oil . . . . . . . . . 10.9Nautilus Personal Watercraft Oil . 10.17XTC-50 . . . . . . . . . . . . . . . . . . . . 10.18
Turbine Oils
Gas AeroShell Turbine Oils (synthetic) . . 4.8Shell Turbo T (mineral) . . . . . . . . 7.58
Steam Shell Turbo T . . . . . . . . . . . . . . . . 7.58
White Oil Shell Fluid FM 32 . . . . . . . . . . . . 7.3
Wire Rope Lubricants Classlube. . . . . . . . . . . . . . . . . . . 7.5
PRODUCT APPLICATION GUIDE
2.7
3.2
Page
General Application GuideShell Engine Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3
Antifreeze / CoolantShellzone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4Rotella ELC Extended Life Coolant . . . . . . . . . . . . . . . . 3.5
Engine OilsRotella T with XLA (Multigrade) . . . . . . . . . . . . . . . . . . 3.20Rotella T Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.24Rotella T SB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.22Rotella T Single Grade . . . . . . . . . . . . . . . . . . . . . . . . . 3.18Shell Fleet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16FormulaShell Engine Oils
Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14Mineral and synthetic blend . . . . . . . . . . . . . . . . . . 3.12SAE 30 and SAE 40 . . . . . . . . . . . . . . . . . . . . . . . . . 3.15
Gear OilsDentax Automotive Gear Oils . . . . . . . . . . . . . . . . . . . 3.26Spirax HD Gear Oils . . . . . . . . . . . . . . . . . . . . . . . . . . 3.27Dentax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.28Spirax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.29
GreasesDarina XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20Albida LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30Darina AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.18
Transmission FluidsDonax CFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11Donax TG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10Donax TD and TDL . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8Donax TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6Donax TF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9
AUTOMOTIVE LUBRICANTS
3.1
Table of Contents
AU
TOM
OTIV
E
3.2
AUTOMOTIVE LUBRICANTS
3.3
General Application Guide for Shell Engine Oils
For Lightand Heavy
DutyGasolinePoweredEngines
Yes
YesYes
Yes Yes
Yes
YesYes
YesYes
Yes*YesYesYes
YesYesYesYes Yes
Product
Rotella T Plus15W-40
Rotella T with XLA10W-3015W-40
Rotella T10W
20W-20304050
Rotella T SBSyn. Blend 10W-40Syn. Blend 0W-30Syn. Blend 5W-30100% Syn. 0W-40
Shell Fleet10W-3015W-40
10W30
FormulaShell 100% Synthetic
5W-3010W-30
FormulaShell Synthetic Blend
5W-205W-3010W-3020W-50
FormulaShell 5W-3010W-3010W-40
3040
ForHeavyDutyDiesel
PoweredEngines
Yes
YesYes
YesYes
Yes
YesYes
For LightDutyDiesel
PoweredEngines
Yes
YesYes
Yes Yes Yes Yes Yes
YesYes Yes Yes
YesYesYes Yes
YesYes
For DetroitDiesel 2-CycleDiesel
PoweredEngines
Yes Yes Yes
.
Yes
ForHydraulics
andAncillaries
Yes
. Yes Yes Yes
Yes
*YOU MUST CONSULT OWNERS’ MANUAL FOR APPLICATION OF THIS PRODUCT.
Recommended Applications:• All-purpose coolant for both heavy-duty and gasoline-
powered, liquid-cooled engines
Advantages:• Low silicate• Low dissolved solids• Excellent aluminum corrosion protection• Excellent heat transfer properties• Superior anti-foam properties
Approvals:• GM 1825M• GM 1899M• ASTM D 3306• ASTM D 4985
Properties SHELLZONE
Product Code 482-011
Specific Gravity, 15.0/15.0 °C 1.13
pH 33% solution 10.4
Reserve Alkalinity (ml) 11.3
Freeze Point, 50% solution, °C -37
Colour Green
AUTOMOTIVE LUBRICANTS
Shellzone — Universal Antifreeze / Coolant 5.10.05
3.4
AUTOMOTIVE LUBRICANTS
3.5
Rotella ELC Extended Life Coolant 5.14.04
Recommended Applications:• Heavy-duty diesel engine coolant capable of long life usage• Gasoline-powered, liquid-cooled engines
Advantages:• 1,000,000 kms or 12,000 hours of service• One time use of Rotella ELC Extender at 500,000 kms
or 6,000 hours• No SCA testing required• No SCA containing filters required• Reduced volume of used coolant for disposal• Rotella ELC / pre-diluted protection to -50°C
Approved for/meets requirements of:• Caterpillar EC-1, Detroit Diesel, Cummins, Navistar,
TMC RP329,ASTM 3306 and ASTM D4985
Product Codes Product
482-005 Rotella ELC Extended Life Coolant / Concentrate
482-006 Rotella ELC Extended Life Coolant / Pre-diluted
482-007 Rotella ELC Extender
A series of premium Caterpillar TO-4 approved fluids.
Recommended Applications:• Cat Powershift transmissions with Variable Capacity Torque
Convertors (VCTC)• Cat hydrostatic transmissions• Cat torque convertors, hoists brakes and hydraulic systems• Cat final drives• Also suitable for use in older Cat equipment• NOT to be used as an engine oil
Advantages:• Contains an additive system specifically designed for newer
Caterpillar transmissions and other drive line components• Improved transmission life• Superior frictional characteristics and efficiency• Suitable for use in older Cat equipment• Three single grades (10W, 30, 50) for seasonal flexibility• One multigrade (Lowtemp) for all-season use in
some components• “Lowtemp” is not fully approved for Cat TO-4, though it uses
the same performance additives approved for the TG-4 fluid• Formulated for superior antiwear, antifoaming and
oxidation stability
Approvals:• Single grades are Cat TO-4,TO-2 approved• Allison C-3, C-4
AUTOMOTIVE LUBRICANTS
3.6
Donax TC - Caterpillar TO-4 Fluid 1.31.06
AUTOMOTIVE LUBRICANTS
3.7
Donax TC — Caterpillar TO-4 Fluid 1.31.06
Prop
ertie
s D
ON
AX
TC
Gra
des
LOW
TEM
P10
W30
50
Prod
uct C
ode
436-
115
436-
110
436-
111
436-
112
Visc
osity
, cSt
40°C
35.5
38.3
108
229.
3
100°
C7.
66.
211
.719
.3
Visc
osity
Inde
x19
010
897
95
Broo
kfie
ld V
isco
sity
, cP
-15°
C-
--
--
-31
,650
-26°
C-
--
-73
,786
- -
-35°
C-
-86
,160
- -- -
-40°
C7,
881
- -
- -
- -
HTH
S Vi
sc @
150
°C, c
P2.
322.
103.
505.
22
Pour
Poi
nt, °
C-5
7-3
3-3
0-2
1
AUTOMOTIVE LUBRICANTS
3.8
Mineral based, heavy duty transmission and hydraulic fluidprimarily for use where one oil system supplies the hydraulics,transmission, differential, power takeoff, wet brakes and steering.
Recommended Applications:• Off highway farm, construction and forestry equipment• Gears, differentials, final drives, transmissions• Hydraulic systems• Bearings• Wet brakes, PTO (power takeoff) clutches
Advantages:• TDL is a lighter, low temperature, winter version of Donax TD• Improved EP and antiwear for gears and hydraulic pumps• Frictional characteristics designed to improve braking, reduce
chatter and noise in brakes and provide positive clutchengagement
• Rust and corrosion protection
Approvals:• John Deere J20C (Donax TD), John Deers J20D (Donax TDL)• Ford New Holland M2C134D• Allison C-4• Recommended for John Deere, Case-International, Ford New
Holland, Massey Ferguson,Allis Chalmers, Oliver-White,Kubota,Versatile, Minneapolis-Moline, Deutz-Allis,Agco
Properties DONAX
Products / Grades TD TDL
Product Code 436-104 436-103
Viscosity, cSt40°C 52.4 34.2100°C 9.5 7.1
Viscosity Index 150 189
Brookfield Viscosity, cP@ -20°C 1,700 - -@ -25°C - - 2,465@ -35°C 59,300 9,710@ -40°C - - 20,000
Pour Point, °C -42 -48
Flash Point, °C 228 190
Donax TD and TDL - Universal Tractor Fluids 1.20.02
AUTOMOTIVE LUBRICANTS
3.9
Automatic transmission fluid meeting Ford’s EWSM2C33-F(Type F) Fluid
Recommended Applications:• Automatic transmissions of some 1977 and earlier Ford cars
and trucks where Type F is specified• Other applications where Type F is specified• Saab 900 3-speed transmissions• Jaguar (1990/92 Borg-Warner automatic transmissions)
Advantages:• Dyed red for identification
Approvals:• Ford EWSM2C33-F (Type F)
Properties DONAX TF
Grades TF
Product Code 436-107
Colour Red
Viscosity, cSt100°C 7.2
Brookfield Viscosity, cSt-18°C 1,290-40°C 34,500
Pour Point, °C -46
Phosphorous, % mass 0.022
Donax TF - Automatic Transmission Fluid (Type F)
Premium, GM Dexron* and Ford Mercon* automatic transmission fluid.
Recommended Applications:• GM passenger car and light duty truck automatic transmissions• Where Ford Mercon*,Type CJ and Type H fluids are recommended• Heavy duty truck transmissions requiring Allison C-4 or Cat TO-2• Hydrostatic drives in construction equipment• Allison V-730 transmissions• Hydraulic systems requiring an ISO 32 grade oil where water
demulsification is not required• Oil flooded rotary screw and vane compressors requiring an ISO 32
Advantages:• Outstanding low temperature performance• Frictional characteristics designed to optimize transmission
performance• Oxidation and corrosion protection• Antiwear protection for transmissions and hydraulic systems• Detergents and dispersants to improve system cleanliness• Compatible with most seal materials and other mineral oils
Approvals:• GM Dexron* IIIG• Ford Mercon*, ESP 138-CJ, M2C 166-H • Allison C-4, Cat TO-2• Spicer transmissions• Voith DIWA transmission• Meets Vickers 35VQ25 hydraulic pump test• Meets Denison HF-1 and HF-2 requirements for
hydraulic vane and piston pump• Sundstrand hydraulics• See our “Lubricants Report for a more complete list
Properties DONAX TG
Product Code 436-106
Colour Red
Viscosity, cSt @ 40°C 36@ 100°C 7.5
Viscosity Index 200
Brookfield Viscosity, cP @-20°C 1,290
Pour Point, °C -45
Flash Point, °C 175
Donax TG - Automatic Transmission Fluid (ATF) 1.07.14
AUTOMOTIVE LUBRICANTS
3.10
3.11
Specifically designed and approved for modern Caterpillar finaldrives and axles that do not contain friction materials.
Recommended Applications:• Provides greater protection and lubrication of severely loaded
gears in Caterpillar final drives and axles compared toconventional TO-4 fluids.
• For applications where friction materials are present DonaxTC TO-4 approved lubricants are recommended.
• NOT recommended for engines, transmissions, hydraulicsystems, or final drives and axles that contain frictionmaterials and/or wet brakes.
Advantages:• Specifically designed for equipment operating under severe
heavy loads.• Provides extended life and reduced wear of final drives and
axles.• Excellent Timken and FZG wear performance• Superior oxidation stability and anti-corrosion properties• Compatible with Caterpillar seals and Cat.TO-4 lubricants
Approvals:• Approved for Caterpillar final drive and axle lubricant
specification FD-1
Properties Donax CFD 60
Product Code 436-117
ViscositycSt (mm2/s) at 40°C 335cSt (mm2/s) at 100°C 25.6
Viscosity Index 98
Density at 15°, kg/m 3,897
Pour Point, ° C -15
Flash Point, ° C 253
AUTOMOTIVE LUBRICANTS
Donax CFD 60 - Premier Gear Lubricant for Caterpillar Final Drives/Axles 1.22.01
Mineral and synthetic blend engine oils.
Recommended Applications:• Domestic and imported gasoline powered passenger cars and
light duty trucks• Recommended for Liquified Propane Gas (LPG) and
Compressed Natural Gas (CNG) fuelled engines• 4-cycle motorcycles in the appropriate viscosity grade
Advantages:• All-season performance• Synthetic blends provide improved low temperature fast flow
characteristics• Superior wear protection• Maintains excellent engine cleanliness• Energy conserving 5W-20, 5W-30 and 10W-30 formulations• Special base stocks to provide low oil consumption
Approvals:• API SL, SJ (also older SH)• 5W-20, 5W-30 and 10W-30 grades exceed ILSAC GF-3
(also ILSAC GF-2)• JASO T903 MA Quality
AUTOMOTIVE LUBRICANTS
3.12
FormulaShell - Engine Oils 1.36.06
Prop
ertie
sFo
rmul
aShe
ll En
gine
Oils
Gra
des
Synt
hetic
Ble
ndSy
nthe
tic B
lend
Synt
hetic
Ble
ndSy
nthe
tic B
lend
5W-2
05W
-30
10W
-30
20W
-50
5W-3
010
W-3
010
W-4
0
Prod
uct C
ode
425-
361
425-
366
425-
367
425-
368
425-
380
425-
385
425-
386
Visc
osity
, cSt
40°C
47.1
64.3
67.3
157.
064
.768
.397
.010
0°C
8.5
11.1
10.5
17.7
11.1
10.5
14.5
Visc
osity
Inde
x15
716
614
412
416
514
215
4
CC
S (c
rank
ing)
, cP
@ -
10°C
---
--
-7,
181
- -
- -
- -
@ -
20°C
---
-4,
995
- -
- -
5,57
85,
973
@ -
25°C
4,07
25,
223
- -
- -
5,56
5-
--
-
Bord
erlin
e Pu
mpi
ngTe
mp.
(MRV
), °C
-4
6.8
-40.
4-3
6.8
-26.
2-3
9.3
-36.
0-3
3.8
Pour
Poi
nt, °
C-4
5-4
2-3
9-3
3-4
2-3
9-3
6Fl
ash
Poin
t, °C
190
225
237
231
225
235
239
3.13
FormulaShell - Engine Oils 1.36.06
AUTOMOTIVE LUBRICANTS
Premium full synthetic engine oils
Recommended Applications:• Domestic, Japanese and European gasoline powered passenger
cars and light duty trucks• Including high performance and turbocharged gasoline
engines• Light duty diesel engines requiring a CF engine oil• Recommended for Liquified Propane Gas (LPG) and
Compressed Natural Gas (CNG) fuelled engines• Recommended for Corvette engines
Advantages:• All-season use• Superior wear protection• Excellent engine cleanliness• Outstanding high temperature performance• Superior low temperature performance• Energy conserving• Synthetic base oils provide even lower oil consumption
Approvals:• API SL (also older SJ)• ILSAC GF-3• GM 4718M (Corvette engines)• API CF
Properties FormulaShell 100% Synthetic Engine Oils
Grades 5W-30 10W-30
Product Code 425-378 425-379
Viscosity, cSt40°C 58 60100°C 10.5 10.1
Viscosity Index 165 150
CCS (cranking),cP@ -25°C - - 3,731@ -30°C 3,827 - -
Borderline Pumping Temp. (MRV), cP@ -30°C - - 9,500@ -35°C 12,900 - -
Pour Point, °C -48 -45
Flash Point, °C 227 235
AUTOMOTIVE LUBRICANTS
3.14
FormulaShell - 100% Synthetic Engine Oils 1.37.02
Recommended Applications:• Gasoline-powered engines where single grades are specified• Small construction equipment• 4 stroke lawnmowers• Older farm equipment
Advantages:• Superior wear protection• Maintains excellent engine cleanliness• Outstanding high temperature performance• Low oil consumption
Approvals:• API SL• API CD (obsolete)
Properties FormulaShell
SAE Grade 30 40
Product Code 425-380 425-384
Viscosity, cSt@ 40°C 96.4 140,7@ 100°C 11.5 14.6
Viscosity Index 107 102
Pour Point, °C -33 -27
AUTOMOTIVE LUBRICANTS
3.15
FormulaShell SAE 30 and SAE 40 1.38.02
Premium engine oils for severe diesel and gasoline service.
Recommended Applications:• Moderate and severe service gasoline and diesel mixed fleets• On-highway and off-highway, construction, farm, woodland,
marine or stationary power plants• Naturally aspirated and high output turbocharged and after-
cooled diesel engines including the latest low-emissiondesigns
• High output Cummins, Caterpillar, Detroit Diesel, Navistar andMack.
• Transmissions requiring an Allison C-3 / C-4 or Cat CD / TO-2transmission fluid including Allison Powershift transmissions
• Hydraulics where water separation is not an issue• Ford, GM, Chrysler and other engine builders
Advantages:• Soot control -suited for low emission engines where soot
related oil thickening is an issue• Oxidation / thermal stability control deposits and engine
cleanliness• Wear protection• Base retention neutralizes acids and protects against corrosion• Viscosity retention• Filterability maintained over the life of the oil• Foam control
Approvals:• API CH-4, CG-4, CF-4, CF/SJ (15W-40)• API CH-4, CG-4, CF-4, CF/SH (10W-30)• SAE 30 grade meets CF-2,CF• Meets Mack EO-M Plus (15W-40 and 10W-30)• Meets Caterpillar SEBU 6385-02, 6251-05, 6250-04• Meets Cummins CES 20076 (15W-40 and 10W-30)• Meets Detroit Diesel Bulletin 7SE270 latest version• Volvo VDS (15W-40)
AUTOMOTIVE LUBRICANTS
3.16
Shell Fleet - Heavy Duty Engine Oils 1.12.11
Properties SHELL FLEET
Grades 15W-40 10W-30 10W 30
Product Code 431-454 431-452 431-451 431-453
Viscosity, cSt40°C 112.1 72.1 38.5 97.7100°C 15.2 11.1 6.3 11.5
Viscosity Index 142 145 113 106
Pour Point, °C -33 -36 -39 -30
CCS Viscosity, cP-20° C 6,229 - - - - - --25° C - - 5,814 5,328 - -
Borderline Pumping
Temperature, °C -31 -34 -33 - -
TBN-E 10 10 6 6
Sulphated Ash, %wt 1.25 1.25 0.75 0.75
AUTOMOTIVE LUBRICANTS
3.17
Shell Fleet - Heavy Duty Engine Oils 1.12.11
Premium mineral oil, single grade diesel engine oils
Recommended Applications:• Heavy-duty 4 stroke diesel engines• In appropriate grade, Detroit Diesel 2 stroke diesel engines• HD transmissions
Advantages:• High temperature piston cleanliness• Freedom from turbo-charger deposits• Resistance to cylinder bore and ring wear• Prevention of low temperature sludge formation
Approvals:• API CF (10W and 20W-20 grades)• API CF-2, CF (30, 40 and 50 grades)• API CC, CD (obsolete)• Allison C-4
AUTOMOTIVE LUBRICANTS
3.18
Rotella T Single Grade Diesel Engine Oils 1.21.02
AUTOMOTIVE LUBRICANTS
3.19
Rotella T Single Grade Diesel Engine Oils 1.21.02Pr
oper
ties
ROTE
LLA
T S
ING
LE G
RAD
E
Gra
des
10W
20W
-20
3040
50
Prod
uct C
ode
431-
401
431-
402
431-
403
431-
406
431-
407
Visc
osity
, cSt
40°
C38
.561
.797
.714
2.1
216.
510
0°C
6.3
8.6
11.5
14.6
19.1
Visc
osity
Inde
x11
311
010
610
199
Col
d C
rank
Sim
ulat
or
@-1
5°C
- -
3,14
5-
--
--
-@
-25°
C5,
328
- -
- -
- -
- -
TBN
- E6.
06.
06.
06.
06.
0
Sulp
hate
d A
sh, %
wt
.75
.75
.75
.75
.75
App
aren
t Vis
cosi
ty (M
RV) c
P
@-3
0°C
13,6
00-
--
--
--
-@
-20°
C-
-6,
825
- -
- -
- -
Shell’s top-of-the-line engine oil for heavy duty diesel and mixedfleets of diesel and gasoline engines
Recommended Applications:• Heavy duty 4 stroke diesel engines• Gasoline engines• HD Transmissions• See Rotella T Single Grade Diesel Engine Oils for most
Detroit Diesel 2 stroke engine applications• Hydraulic systems where water separation is not needed• Pump and compressor crankcases where product
rationalization is important
Advantages:• Rotella T with XLA has exclusive advanced additive
technology with proven “Million Mile Oil” durability• Excellent deposit control• Suitable for use in multiple applications to reduce oil
inventories• Excellent antiwear properties in hydraulic systems
Approvals:• API CH-4, CG-4, CF-4,CF• API SJ (15W-40)• API SH (10W-30)• Mack EO-M Plus, EO-M, EO-L Plus• Cummins CES 20076, CES 20071• Volvo VDS-2 (15W-40)• Allison C-4
AUTOMOTIVE LUBRICANTS
3.20
Rotella T with XLA - Premium Engine Oils 1.10.31
Properties ROTELLA T with XLA
Grades 15W-40 10W-30
Product Code 431-405 431-404
Viscosity, cSt40° C 100.5 76.7100° C 14.0 11.8
Viscosity Index 155 149
CCS (cranking), cP@ -20° C 6,136 - -@ -25° C - - 5,982
Borderline Pumping, °C -33 -35
Pour Point, °C -36 -39
Sulphated Residue, % 1.2 1.3
TBN-E 9.0 10.3
AUTOMOTIVE LUBRICANTS
3.21
Rotella T with XLA - Premium Engine Oils 1.10.31
Synthetic blend versions of Shell’s top-of-the-line engine oil forheavy duty diesel and mixed fleets of diesel and gasolineengines.
Recommended Applications:• Heavy duty 4 stroke diesel and gasoline engines• HD transmissions requiring C-4 fluid• Hydraulic systems where water separation is not needed• Pump and compressor crankcases where product
rationalization is important
Advantages:• Improved soot control• Excellent low temperature properties• Potential fuel economy benefits
Approvals:• SB 0W-30:API CH-4, CG-4, CF-4, CF/SJ, Mack E0-M Plus,
Cummins CES 20071,Allison C-4• SB 5W-30:API CF,Allison C-4• SB 100% 0W-40:API CG-4, CF-4, CF/SJ,Allison C-4• SB 10W-40:API CH-4, CG-4, CF-4, CF/SJ, Mack EO-M Plus,
Cummins CES 20076,Volvo VDS-2,Allison C-4
AUTOMOTIVE LUBRICANTS
3.22
Rotella T SB - Premium Engine Oils 1.15.08
Properties ROTELLA T SB
Grades 10W-40 5W-30 0W-30 0W-40100% Syn.
Product Code 431-640 431-635 431-630 431-634
Viscosity, cSt40° C 91 67.8 63.8 86.2100° C 14.9 11.5 11.5 14.9
Viscosity Index 172 165 177 182
CCS (cranking), cP@ -25° C 6,200 -- -- --@ -30° C -- 5,890 -- --@ -35° C -- -- 5,101 4,911
Pour Point, °C -42 -45 -54 -48
Sulphated Residue, % 1.2 1.2 1.0 1.2
MRV TP-1@ -30° C 19,444 -- -- --@ -35° C -- 18,881 -- --@ -40° C -- -- 14,979 15,076
AUTOMOTIVE LUBRICANTS
3.23
Rotella T SB - Premium Engine Oils 1.15.08
All the benefits of Rotella T with XLA plus extended servicecapability. Shell’s top-of-the-line engine oil for heavy duty dieseland mixed fleets of diesel and gasoline engines
Recommended Applications:• Heavy duty 4 stroke diesel engines• Gasoline engines• HD Transmissions
Advantages:• All the benefits of Rotella T with XLA, as well as:
• Improved soot handling capability• Improved valve train wear• Better oxidation stability• Higher base number (TBN) for control of crankcase acids• Better base number retention• Extended Service capability
Approvals:• API CH-4, CG-4, CF-4, CF/SJ• Mack EO-M Plus, EO-M• Cummins CES 20076, CES 20071• Volvo VDS-2• Allison C-4
AUTOMOTIVE LUBRICANTS
3.24
Rotella T Plus - Premium Engine Oils 1.11.09
Properties ROTELLA T PLUS
Grades 15W-40
Product Code 431-410
Viscosity, cSt40° C 100.1100° C 14.0
Viscosity Index 142
CCS (cranking), cP@ -20° C 5,720
Borderline Pumping (MRV), °C(based on 60,000 cP max.) -32
Pour Point, °C -36
Sulphated Residue, % 1.4
TBN-E 10
Flash Point, °C 216
AUTOMOTIVE LUBRICANTS
3.25
Rotella T Plus - Premium Engine Oils 1.11.09
Dentax 80W-90 and 140 are premium, non-EP automotive gearoils designed for manual transmissions specifying “straightmineral” gear oils meeting API GL-1.
Recommended Applications:• Dentax 80W-90 and 140 are straight mineral gear oils
designed for use where EP additives are not recommended• Usually recommended for non-ferrous gears including spiral
bevel, helical and straight gear applications• Recommended for tractor transmissions and final drives
calling for API GL-1 lubricants• Recommended for some manual transmissions, such as Meritor
Advantages:• Good oil film strength to protect gears• Contains rust and oxidation inhibitors• Contains viscosity modifiers to improve low temperature flow
characteristics
Approvals:• Dentax 80W-90 and 85W-140 meet API GL-1
Properties DENTAX OILS
Grades 80W-90 140
Product Code 436-005 436-004
Viscosity, cSt100°C 14.5 31.6
Viscosity Index 95 92
Brookfield Viscosity, cP@ -12°C -- 112,000@ -26°C 100,000 --@ -40°C -- --
Pour Point, °C -24 10
Flash Point, °C 235 288
AUTOMOTIVE LUBRICANTS
3.26
Dentax Automotive Gear Oils 1.27
AUTOMOTIVE LUBRICANTS
3.27
Spirax HD oils are premium extreme pressure automotivehypoid gear oils.
Recommended Applications:• Spirax HD oils are approved for drive-train gears in heavily
loaded equipment and passenger cars• Including hypoid, spur, helical, spiral-bevel and worm gears in
differentials, manual transmissions, final drives, transfer casesand steering mechanisms
• Spirax HD 85W-140 is typically used in off-highwayapplications
• See Shell Spriax “S”75W-90 for extended warranty applications
Advantages:• Spirax HD oils contain EP additives for superior load carrying
capacity in heavy duty applications• Superior thermal and oxidation stability • Spirax HD 75W-90 is a semi-synthetic oil for improved low
temperature performance and reduced frictional losses forimproved fuel economy
Approvals:• Spirax HD 80W-90 and 85W-140 meet API GL-4, GL-5,
API MT-1, MIL-L-2105D and MIL-PRF-2105E• Spirax HD 80W-90 and HD 85W-140 are Mack GO-H and
GO-J approved• Spirax 75W-90 meets API GL-5
Properties SPIRAX HD GEAR OILS
Grades 75W-90 80W-90 85W-140
Product Code 437-010 437-006 437-007
Viscosity, cSt40°C 109 139 411100°C 19.2 14.8 29.7
Viscosity Index 195 110 103
Brookfield Viscosity, cP@ -12°C -- -- 78,800@ -26°C -- 136,000 --@ -40°C 123,000 -- --
Channel Point, °C < -45 < -35 < -20
Pour Point, °C -42 -27 -12
Flash Point, °C 195 218 200
Spriax HD Automotive Gear Oils 1.08.13
A premium, 100% synthetic, non EP, manual transmission fluidfor extended oil drain warranty programs
Recommended Applications:• Manual transmissions and transfer cases of trucks, farm and
construction equipment requiring a GL-1 type lubricant• Severe service
Advantages:• Extended drain / warranty programs• All-season operation• Outstanding low temperature performance• Outstanding winter fuel economy
Approvals:• Meets API GL-1 requirements• Meets API MT-1 test requirements• Eaton-Fuller PS-081 extended warranty program (E250)• Eaton-Fuller PS-164 extended warranty program (E500)• Meritor 0-81-E extended warranty program
Properties DENTAX S
Grades SAE 50
Product Code 436-007
Viscosity, cSt40°C 127100°C 18.2
Viscosity Index 151
Pour Point, °C -40
Brookfield Viscosity, cP-30°C 38,000
Dentax S - 100% Synthetic Heavy Duty Transmission Fluid 1.29.02
AUTOMOTIVE LUBRICANTS
3.28
AUTOMOTIVE LUBRICANTS
3.29
Spirax S is a premium, 100% synthetic, extreme pressureautomotive gear oil, approved for Eaton-Fuller and Meritorextended warranty programs.
Recommended Applications:• Severe service automotive gear applications• Differentials, heavy duty axles, transfer cases, manual
transmissions of trucks, farm equipment, automobiles andheavy construction equipment
• Some industrial gear applications requiring wide temperaturecapabilities in an ISO 100 or 150 grade
Advantages:• Extended drain warranty program approved• Full synthetic base oil• Excellent wear protection -full automotive EP additive system• Outstanding flow at low temperatures• All season operation• Improved winter fuel economy
Approvals:• API GL-5, MT-1• Meritor 0-76-E, 0-76-N• Eaton Fuller PS-037 (E250), PS-163 (E500)• Mack Truck GO-J, GO-J Plus• Dana Corporation,Axle Division• MIL-L-2105D• MIL-PRF-2105E
Properties SPIRAX S
Grades 75W-90
Product Code 437-013
Viscosity, cSt40°C 122100°C 16.6
Viscosity Index 147
Channel Point @ -51°C Pass
Pour Point, °C -45
Spirax S - 100% Synthetic Heavy DutyAutomotive Gear Oil 1.28.10
Page
FluidsAeroShell Fluid 2F . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7AeroShell Fluid 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7AeroShell Fluid 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7Shell LGF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
GreasesAeroShell Grease 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6AeroShell Grease 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6AeroShell Grease 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6AeroShell Grease 14. . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6AeroShell Grease 22. . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6AeroShell Grease 33. . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6
Piston Engine OilsAeroShell Oil W 15W-50 (semi-synthetic) . . . . . . . . . . . 4.5AeroShell Oil W (dispersant) . . . . . . . . . . . . . . . . . . . . 4.4 AeroShell Oil W 100 Plus (dispersant) . . . . . . . . . . . . . 4.6AeroShell Oil (non-dispersant) . . . . . . . . . . . . . . . . . . . 4.3
Turbine Engine OilsAeroShell 560 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8AeroShell 555 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8AeroShell 500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
AVIATION LUBRICANTS
4.1
Table of Contents
AV
IATIO
N
AVIATION LUBRICANTS
4.2
AVIATION LUBRICANTS
4.3
AeroShell - Piston Engine Oils 5.01.01
AeroShell (non dispersant) aviation piston engine oils.
Recommended Applications:• All grades are for use in 4 stroke certified aircraft
reciprocating piston engines and aircraft radial engines whichdo not require a dispersant additive (AD type) containing oil
Advantages:• AeroShell Oils are oxidation inhibited high quality mineral oils
Approvals:• SAE J-1966 (formerly MIL-L-22851D)
Properties AEROSHELL OIL
Grades 80 100 120
SAE Viscosity Grade 40 50 60
Product Code 420-010 420-015 420-020
Viscosity, cSt40°C 143 232 318100°C 14.6 19.9 25.0
Pour Point, °C -30 -21 -15
Flash Point, °C 282 292 304
Ash Content, % m 0.001 0.002 0.001
AeroShell Oil W (dispersant) monograde aviation piston engineoils.
Recommended Applications:• AeroShell Oil W grades are for use in 4 stroke certified
reciprocating piston engines, including fuel-injected andturbocharged engines. NOT recommended for automotiveengines converted for use in aircraft
• For multigrade aviation piston engine oil see AeroShell Oil W 15W-50 oil
Advantages:• AeroShell Oil W oils promote engine cleanliness, eliminate
sludge, reduce oil consumption and protect against scuffingand wear
Approvals:• SAE J-1899 (formerly MIL-L-22851D)
Properties AEROSHELL OIL W (PISTON ENGINE OILS)
Grades W80 W100 W120
SAE Viscosity Grade 40 50 60
Product Code 420-030 420-035 420-040
Viscosity, cSt40°C 118 199 278100°C 14.1 19.7 24.6
Viscosity Index 118 113 112
Pour Point, °C -33 -30 -18
Flash Point, °C 264 288 284
Ash, % m 0.003 0.003 0.003
AVIATION LUBRICANTS
4.4
AeroShell Oil W - Piston Engine Oils 5.02.01
AVIATION LUBRICANTS
4.5
A premium quality, synthetic blend, ashless dispersant,multigrade aviation piston engine oil.
Recommended Applications:• 4 stroke cycle aircraft piston engines• All season service• Used where a dispersant type aviation grade 100 (SAE 50) oil
is specified
Advantages:• Synthetic blend, antiwear, ashless dispersant formulation• Designed specifically to improve the low temperature flow
characteristics and provide superior lubrication at higherengine operating temperatures
• Significantly reduced flow time to the oil gallery versus 20W-50 and 65 grades at low temperatures
• Excellent wear and corrosion protection• No need to add Lycoming LW16702, as this oil contains an
approved equivalent
Approvals:• Textron-Lycoming (Service No. 1409A, 1014K and Bulletin
446C)• Teledyne Continental spec MHS-24 (Service Bulletin M81-11)• Pratt & Whitney (all radial engines, Service Bulletin 1183 Rev T.)• SAE J1899 (formerly MIL-22851D)• Bell Helicopters Model 47 transmission (Tech Bulletin 47-81-4)
Properties AEROSHELL OIL W 15W-50
Grades 15W-50
Product Code 420-060
Viscosity, cSt40°C 110100°C 19.4
Viscosity Index 170
CCS (cranking) Viscosity, cP -15°C 3,100
Pour Point, °C -42
Flash Point, °C 258
AeroShell Oil W 15W-50 - Piston Engine Oil 5.09.09
AVIATION LUBRICANTS
4.6
A premium quality, ashless dispersant type aviation pistonengine oil with improved corrosion resistance, enhanced anti-wear properties, and includes approved equivalient of LW 16702additive.
Recommended Applications:• 4 cycle aircraft piston engines• All types of service• Used where a dispersant type aviation oil grade 100 is required• Used where LW 16702 is specified as an approved equivalent
additive is included in the formulation• NOT recommended for helicopters with a common sump for
engine and transmission oil
Advantages:• Antiwear, ashless dispersant formulation• Excellent wear and corrosion protection• Excellent oxidation stability and heat dissipation• No need to estimate the amount of LW 16702 additive because
it is already included in AeroShell Oil W 100 Plus
Approvals:• Textron-Lycoming (Service No. 1409A, 1014K and Bulletins
446B, 446C and 446D)• Teledyne Continental spec MHS-24 (Service Bulletin M81-11)• Pratt & Whitney (all radial engines, Service Bulletin 1183 Rev T.)• SAE J1899 (formerly MIL-22851D)• FAA AD 80-04-03 R2
Properties AEROSHELL OIL W 100 PLUS
Grades 100
Product Code 420-065
Viscosity, cSt40°C 213100°C 20.2
Viscosity Index 110
Pour Point, °C -20
Flash Point, °C 260
AeroShell Oil W 100 Plus - Piston Engine Oil 5.15.01
Four premium products for various aviation applications
Recommended Applications:• AeroShell Fluid 2F is a corrosion inhibiting oil intended
for preserving internal engine parts during storage• AeroShell Fluid 4 is a mineral oil based aviation
hydraulic fluid • AeroShell Fluid 41 is a “super clean” hydraulic fluid• Shell LGF is used in landing gear strut mechanisms
Advantages:• Fluid 2F has an anti-corrosion additive package and may
be used as a “flyaway” oil for up to 50 hours after storage• Fluid 4 and 41 are mineral hydraulic oils that provide
excellent low temperature fluidity
Approvals:• Fluid 2F is a P-10 preservative under MIL-C-6529C• Fluid 4 is approved for MIL-H-5606A (obsolete)• Fluid 41 is approved for MIL-H-5606G for “super clean” fluids• Shell LGF is approved for many commercial aircraft• See our “Lubricants Report” for more details
Properties AEROSHELL FLUIDS
Products Fluid 2F Fluid 4 Fluid 41 Shell LGF
Product Code 421-035 421-150 421-141 421-152
Colour Dk Amber Red Red Yellow
Viscosity, cSt40°C - - 13.5 13.6 13.7100°C 20.0 5.1 5.1 5.0- 40°C - - 480 380 390
TANE - - 0.03 0.07 5.0
Ash, % mass 0.004 - - - - - -
Pour Point, °C -10 -60 -60 -60
Flash Point, °C 210 88 88 10
AVIATION LUBRICANTS
4.7
AeroShell Fluids
AVIATION LUBRICANTS
4.8
100% synthetic gas turbine engine oils.
Recommended Applications:• AeroShell Turbine Oil 500 is approved for use in aviation
turbines and industrial gas turbine engines• AeroShell Turbine Oil 555 is approved for use in aviation
turbines and helicopter transmissions• AeroShell Turbine Oil 560 is approved for aviation turbines
and industrial gas turbine engines
Advantages:• AeroShell Turbine Oil 560 is a third generation “low coking”
oil designed for newer high bypass engines• Improved thermal and oxidation stability
Approvals:• AeroShell Turbine Oil 500 is MIL-PRF-23699F Grade STD
approved• AeroShell Turbine Oil 555 is DOD-L-85734 approved and also
meets MIL-PRF-23699F standards• AeroShell Turbine Oil 560 is MIL-PRF-23699F Grade HTS
approved for newer generation engines• Please refer to our “Lubricants Report” for a complete listing
of engine manufacturer and model approvals.
Properties AEROSHELL TURBINE OILS
Products 500 555 560
Product Code 420-120 420-121 420-130
Viscosity, cSt40°C 25.3 29.0 28.3
100°C 5.2 5.4 5.3- 40°C 10,025 10,775 10,775
Pour Point, °C max -54 -54 < -54
Flash Point, °C min 246 246 260
TANE 0.11 0.14 0.14
Ryder Gear Test, %Hercolube A, 102 min. 117 > 145 126
AeroShell Turbine Engine Oils 5.13.01
The following Shell lubricants satisfy the requirements for foodcontact:
US FDA CFIA
Product Satisfies Approved Page
GREASES
Alvania EP n1 6.12
Shell FM Grease H1 6.16Darina XL – EP2, Moly, MS, 102 Moly n1 6.20
SRS 2000 n1 6.30
OILS
Shell Fluid FM 32 H1 n3 7.3
Corena AS n1 7.10
Diala AX n1 7.22
Dromus B n1 7.24
Morlina n1 7.30
Omala 68, 100, 150, 220, 320, 460, 680, 1000 n1 7.38
Omala HD n1 7.40
Omala RL n1 7.41
Tellus n2 7.46
Tellus T n2 7.50
Shell Turbo T n1 7.58
Federal departments (Drug Administration,Agriculture, etc.)monitor the use of lubricants used in food processing plants.
US FDA Designations:H1: Satisfactory for incidental contact with food.
CFIA (Canadian Food Inspection Agency) Designations:n1: For general use; avoid food contamination during
application and storage.n2: Hydraulic oil; avoid food contamination during application
and storage.n3: Protective coating oils.
FOOD GRADE LUBRICANTS
5.1
Designations and Table of Contents
FOO
D G
RA
DE
Page
Grease Reference Chart . . . . . . . . . . . . . . . . . . . . . . . 6.3
Automotive Chassis / Wheel BearingDarina XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20Albida LC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30Darina AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.18
AviationAeroShell Greases . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6
Drill RodDiamond Drill Rod. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.22
Electric Motor Cyprina RA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.17Alvania 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.14
Food Machinery Shell FM Grease 1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.16
High Temperature (Extreme)Ultragel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.33
MolyDarina XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20Alvania EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30
Multi-PurposeDarina XL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20Albida LC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30Alvania EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12
Non-EP BearingAlvania 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.14
GREASES
6.1
Table of Contents
GREA
SES
GREASES
6.2
Page
Open GearMalleus GL Multilube . . . . . . . . . . . . . . . . . . . . . . . . . . 6.24
RailwayCardura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.15Alvania EP D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.10Cyprina RA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.17
Semi-FluidSurstay EP 000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.32Retinax TL 00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.28Ossagol C Moly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.27Alvania EP Arctic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12Alvania EP Arctic Moly . . . . . . . . . . . . . . . . . . . . . . . . . 6.12
SnowmobileAdvance Snow Ultra. . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4
Synthetic Darina XL 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20Retinax TL 00. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.28SRS 2000 (Partial Synthetic) . . . . . . . . . . . . . . . . . . . . . 6.30AeroShell Greases . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6
Thread Compound Malleus TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.26
Valve (Sour Gas) Dursol K1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.23
Water Resistant SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30
Table of Contents (continued)
1=Excellent; 2=Very Good; 3=Good; X=Not Suitable (M)=Moly Grades
Application/Characteristic
High Temp
Low Temp
MechanicalStability
Water Resistance
Anti Rust
Extreme Pressure (EP)
Farming
Construction
Trucking
Manufacturing
Marine-Leisure
Logging
Wheel Bearings
Other Bearings
Pillow Blocks
General ChassisComponents
King Pins, Cupsand Saucers
Universal Joints
Slack Adjusters
Pins and Bushings
5th Wheels
Splines, Yokes
Couplings
Car Washes
Boat Trailers
ATVs
Irrigation
GREASES
6.3
Grease Reference Chart
Darina XL
102M
1
1
1
3
2
1
2
1
2
1
1
1
1
2
1
1
2
3
2
1
1
2
3
3
3
2
3
EP-2 (M)
2
3
2
2
2
2
1
2
2
1
2
2
1
2
2
2
3
3
3
2
2
3
3
2
2
2
2
SRS 2000
S
3
X
1
1
1
2
2
2
1
1
2
2
3
3
X
2
1
1
2
1
1
2
1
1
1
2
1
W
X
2
2
2
2
2
3
3
2
3
1
3
X
3
3
3
3
3
2
3
2
3
3
2
2
2
3
Albida
EP-1&2
2
3
2
2
2
2
2
2
1
1
2
2
1
2
1
2
2
2
2
2
2
1
2
2
2
2
2
Alvania EP
EP-1&2
3
3
2
2
2
2
2
2
2
2
2
2
3
1
2
2
2
2
2
2
2
2
2
2
2
2
2
MS (M)
X
2
2
3
3
2
3
3
3
3
3
3
X
3
3
3
3
3
3
3
3
3
3
3
3
3
3
GREASES
6.4
A fully synthetic, extreme pressure (moly) grease.
Recommended Applications:• All snowmobile grease applications including recreational,
competitive racing and long endurance conditions• Chassis points, pins and bushings, plain and rolling element
bearings
Advantages:• Synthetic base oils provide better performance over a wider
temperature range• Excellent load carrying / shock loading ability to minimize
bearing and suspension wear• Contains a fine dispersion of moly extreme pressure additive• Superior low temperature mobility and dispensability• Excellent lubrication as low as -40°C• Excellent resistance to water washout• Excellent adhesive qualities• Superior mechanical stability• Prevents corrosion
Approvals:• Meets NLGI GC-LB wheel bearing and chassis requirements
Properties ADVANCE SNOW ULTRA GREASE
NLGI Grades 1
Product Code 504-593
Colour Grey
Thickener type Microgel
Dropping Point, °C 260 +
Base Oil Viscosity, cSt 40°C 100
4 Ball Wear, mm 0.6
4 Ball EP, Load Wear Index 70
Est. Operating Range, °C -45 to 170
Min. Dispensing Temp, °C (may vary with grease gun or application technique) -40
Advance Snow Ultra - Synthetic Snowmobile Grease
GREASES
6.5
GREASES
6.6
Six premium greases designed for aviation applications andspecifications, utilizing various thickeners and both mineral andsynthetic base oils.
Recommended Applications:• AeroShell Grease 5: wheel bearings, high speed accessories
such as starters• AeroShell Grease 6: multi-purpose, anti-friction and plain
bearings• AeroShell Grease 7: heavily loaded gears, actuators, propellers,
screws • AeroShell Grease 14: helicopter main and tail rotor bearings• AeroShell Grease 17: heavily loaded boggie pins on landing
gear assemblies• AeroShell Grease 22: high speed, heavily loaded applications
over wide temperature ranges• AeroShell Grease 33: multi-purpose airframe grease developed
for Boeing 3-33A
Please Note:AeroShell greases are not necessarily compatiblewith other greases. Always be sure to clean and completelyremove all old greases before installing the new AeroShellgreases.
Advantages:• AeroShell greases are designed to resist oxidation and thermal
breakdown, resist water washout, and prevent corrosion• Provide high load carrying capabilities in the intended
applications• Perform over a wide range of temperatures
AeroShell Greases
Prop
ertie
sA
ERO
SHEL
L G
REA
SES
Gra
des
Gre
ase
5G
reas
e 6
Gre
ase
7G
reas
e 14
Gre
ase
17G
reas
e 22
Gre
ase
33
Prod
uct C
ode
519-
005
519-
006
519-
010
519-
015
519-
025
519-
035
519-
033
Col
our
Am
ber
Brow
nBu
ffTa
nD
ark
Gra
yTa
nG
reen
Thic
kene
r M
icro
gel
Mic
roge
lM
icro
gel
Cal
cium
Mic
roge
lM
icro
gel
Lith
ium
Base
Oil
Min
eral
Min
eral
Synt
hetic
Min
eral
Synt
hetic
Synt
hetic
Synt
hetic
Dro
ppin
g Pt
, °C
+215
+215
+260
+148
+260
+260
+250
Oil
Visc
osity
, @ 9
8.9°
C31
.85.
53.
13.
13.
15.
83.
4
Pene
tratio
n @
25°
CU
nwor
ked
281
287
283
267
287
271
290
Wor
ked
284
300
296
273
295
275
297
Ope
ratin
g Te
mp
Rang
e, °
C-2
3 to
+17
7-4
0 to
+12
1-7
3 to
+14
9-5
4 to
+93
-73
to +
149
-65
to +
204
-73
to +
121
US
Mili
tary
App
rova
ls M
IL-G
-354
5M
IL-G
-241
39M
IL-PR
F-23
827
MIL-
G-2
5537
MIL-
G-2
1164
MIL-
G-8
1322
MIL-
PRF-
2382
7(o
bsol
ete)
Gra
de A
BMS
3-33
A
GREASES
6.7
AeroShell Greases
A premium, multi-purpose, high temperature, extreme pressurelithium complex grease.
Recommended Applications:• General multi-purpose, heavy duty applications• Including mining and smelting, steel, pulp and paper, and
cement industries• Pins and bushings, plain and rolling element bearings
Advantages:• Compatible with most other greases• Outstanding mechanical stability• Temperature range from -40 to 160°C • Excellent load carrying ability• Superior low temperature mobility and dispensability• Resistant to water washout• Excellent rust protection• Coloured green for identification
Approvals:• EP-1 and EP-2 meet NLGI GC-LB wheel bearing and
chassis requirements
GREASES
6.8
Albida LC - Premium Multi-Purpose Grease 3.74.06
GREASES
6.9
Prop
ertie
sA
LBID
A L
C
Prod
uct
EP-2
EP-2
Mol
yEP
-1EP
-MS
Prod
uct C
ode
504-
700
504-
701
504-
703
504-
702
NLG
I Gra
de2
21
1
Col
our
Gre
enG
rey
Gre
enG
reen
Thic
kene
r Ty
peLi
thiu
m c
ompl
exLi
thiu
m c
ompl
exLi
thiu
m c
ompl
exLi
thiu
m c
ompl
ex
Wor
ked
Pene
tratio
n 60
stro
kes
at 2
5°C
280
280
325
325
Est.
Ope
ratin
g Ra
nge,
°C
-20
to +
160
-20
to +
160
-30
to +
160
-40
to +
80
Min
dis
pens
ing
tem
p °C
(m
ay v
ary
with
gre
ase
gun
or
appl
icat
ion
tech
niqu
e)-1
5-1
5-2
5-3
5
Dro
ppin
g Pt
, °C
299
280
293
271
Base
Oil
Visc
osity
, cSt
@ 4
0°C
220
220
160
20.8
4 Ba
ll W
ear,
mm
0.5
0.5
0.5
0.5
EP T
ests
4 Ba
ll, L
oad
Wea
r In
dex
5475
5445
4 Ba
ll, W
eld
Load
400
400
400
315
Albida LC - Premium Multi-Purpose Grease 3.74.06
GREASES
6.10
A premium EP long life railroad journal roller bearing grease.
Recommended Applications:• Heavily loaded locomotive and rolling stock wheel bearings
Advantages:• Excellent rust and oxidation resistance• Outstanding oxidation stability and high wear resistance in
heavily loaded applications• Extended trouble free service and long shelf life
Approvals:• Association of American Railroads (AAR) Specification M-942-98
Properties ALVANIA EP D
NLGI Grades 1.5
Product Code 504-534
Colour Brown
Dropping Point, °C 180
Thickener Lithium/Calcium Soap
Base Oil Viscosity, cSt 40°C 173
4 Ball EP, Weld Load 250
Alvania EP D Grease - Railroad Bearing Grease 3.61.03
GREASES
6.11
“New and improved”, premium multi-purpose, extreme pressure(EP), lithium soap based greases.
Recommended Applications:• Multi-purpose, heavy duty automotive, industrial and marine
applications• Pins and bushings, plain and rolling element bearings• Including chassis points, universal joints, water pumps, track
rollers, clutches and wheel bearings• -50°C to 130°C temperature range• Arctic grades are designed for low temperature central
systems• MS (Multi-Season) grades for low temperature grease gun
applications• Moly versions should be used for sliding applications such as
steering gears, king pins, front suspensions, fifth wheels, guideways and booms; EP Arctic Moly for trailer central lubesystems
Advantages:• Improved oxidation stability• Improved mechanical stability• EP for excellent load carrying ability• Compatible with most other greases• Excellent rust protection• Resists water washout
Approvals:• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
GREASES
6.12
Alvania EP - Premium Multi-Purpose Grease 3.14.14
GREASES
6.13
Prop
ertie
sA
LVA
NIA
EP
Prod
uct
EP 2
EP M
oly
EP 1
EP A
rctic
EP A
rctic
Mol
yEP
MS
EP M
S M
oly
NLG
I Gra
de2
21
00
11
Prod
uct C
ode
504-
532
504-
518
504-
531
504-
509
504-
514
504-
513
504-
511
Col
our
Brow
nG
rey
Brow
nBr
own
Gre
yBr
own
Gre
y
Thic
kene
r Ty
peLi
thiu
m s
oap
Lith
ium
soa
pLi
thiu
m s
oap
Lith
ium
soa
pLi
thiu
m s
oap
Lith
ium
soa
pLi
thiu
m s
oap
Dro
ppin
g Po
int,
°C20
020
020
019
019
019
519
5
Base
Oil
Visc
osity
, cSt
40
°C15
015
015
020
2027
27
Tim
ken
OK
Load
, kg
18.2
18.2
18.2
18.2
18.2
18.2
18.2
4 Ba
ll W
ear,
mm
0.5
0.5
0.5
0.6
0.6
0.6
0.6
4 Ba
ll EP
, Wel
d Lo
ad, k
g25
025
025
020
025
025
025
0
Est.
Ope
ratin
g Ra
nge,
°C
-25
to 1
35-2
5 to
135
-30
to 1
35-5
0 to
80
-50
to 8
0-4
0 to
80
-40
to 8
0
Min
. Dis
pens
ing
Tem
p, °
C(m
ay v
ary
with
dis
pens
ing
-20
-20
-25
-45
-45
-35
-35
syste
m)
Alvania EP - Premium Multi-Purpose Grease 3.14.14
GREASES
6.14
A premium non-EP version of the lithium soap based Alvaniagrease line.
Recommended Applications:• Plain and rolling bearings where extreme pressure additives
are not required.• Where low noise performance is required
Advantages:• Excellent rust and oxidation resistance• Additives selected to ensure low noise in rolling element
bearings
Properties ALVANIA GREASE 2
NLGI Grade 2
Product Code 504-522
Colour Amber
Thickener Type Lithium soap
Dropping Point, °C 200
Base Oil Viscosity, cSt40°C 48
Base Oil Viscosity Index 97
Est. Operating Range, °C -25 to 130
Alvania Grease 2 - Non-EP Grease 3.78.02
GREASES
6.15
Two year-round rail-curve greases.
Recommended Applications:• Curved sections of railway track serviced by track-side rail
lubricators• Cardura Plus for steep grades and high curvature applications
which may generate higher wheel temperatures
Advantages:• Retention on tracks• Pumpability / mobility to ensure application at low
temperatures• All-season performance, proven at temperatures from -40°C to
+ 40°C• Reduced rail / wheel wear and maintenance• Potential for improved fuel economy• Excellent track coverage - over 5 km with “WS”,
10 km with “Plus”
Note: Please consult your Shell Product Specialist to determineproper lubricator design
Properties CARDURA
Product WS PLUS
NLGI Grade 1 1
Product Code 504-506 504-508
Colour Black Black
Solid Additives Graphite / Moly Graphite
Thickener Type Calcium Microgel
Dropping Point, °C 142 260+
Base Oil Viscosity, cSt40°C 17.4 22.0
Est. Operating Range, °C -40 to +80 -35 to +80
Low Temp. Pumpability‡ ,Pressure Drop, kPa /m (psi /ft)
@ 0°C 460 (20) - -@ -10°C 650 (29) - -@ -20°C 770 (34) - -@ -30°C 1,100 (49) 1,850 (88)@ -40°C 1,800 (80) 3,800 (168)
‡ Pressure drop in 3/16 inch OD tubing @ shear rate of 1 sec-1.
Cardura - Rail Curve Lubricants 3.81.03
Multi-purpose “food approved” grease.
Recommended Applications:• Lubrication of machinery in food processing and canning
industries where the grease which is used can contaminatethe food being processed
• For use in canneries, beverage bottling plants, candy plants,meat and fish packing plants etc.
• Suitable for year-round and refrigeration applications• For a food grade lubricating oil, see Shell FM Grease 1.5
Advantages:• Multi-purpose• Non-toxic• Excellent resistance to water washout• Protects equipment against water, juices, acids and other
process fluids• Rust and oxidation inhibited• Superior wear and load carrying capacity• Excellent high temperature performance• 1.5 grade for maximum dispensability in indoor centralized
systems
Approvals:• Satisfies the requirements of U.S. Department of Agriculture
(USDA), FDA,Type H1 (incidental food contact)
Properties SHELL FM GREASE 1.5
NLGI Grade 1.5
Product Code 504-811
Colour White
Thickener Type Aluminum complex
Dropping Point, °C 246
Base Oil Viscosity, cSt@ 40°C 67.0
Viscosity Index 85
4 Ball EP, Weld Load, kg 250
Water Washout, % loss @ 38°C 2
GREASES
6.16
Shell FM Grease 1.5 - Food Grade Grease 3.48.04
A premium, non-EP, lithium soap based grease.
Recommended Applications:• Rolling bearings in traction motors of GM Electromotive
Diesels (EMD) and GE Electric locomotives• Conventional electric motor bearings including “lifetime” seal-
for-life units• Suitable for temperatures up to 135°C
Advantages:• Superior mechanical stability for long life• Long oxidation life• Grease hardness suitable for electric motor bearings
Approvals:• Recommended for EMD and GE locomotive electric motor
bearings• Recommended for Westinghouse electric motor bearings
Properties CYPRINA RA GREASE
NLGI Grade 3
Product Code 504-538
Colour Amber
Thickener Type Lithium Soap
Dropping Point, C 195
Est. Operating Range, °C -30 to 135
Base Oil Viscosity @ 40°C 93
GREASES
6.17
Cyprina RA - Electric Motor Bearing Grease 3.57.08
GREASES
6.18
A premium, non EP, multi-purpose automotive wheel bearinggrease.
Recommended Applications:• Automotive chassis parts• Wheel bearings
Advantages:• High temperature protection, dropping point above 250°C• Long life• Rust and corrosion inhibited• Resistance to water washout• High mechanical stability
Approvals:• Meets the requirements of NLGI GB-LB
Properties DARINA AX
NLGI Grade 1.5
Product Code 510-032
Colour Tan
Thickener Type Microgel
Dropping Point, °C None (+250°C)
Base Oil Viscosity, cSt40°C 171
Base Oil Viscosity Index 92
Est. Operating Range, °C -30 to 150
Darina AX - General Purpose Wheel Bearing Grease 1.13.05
GREASES
6.19
Premium multi-purpose, extreme pressure (EP), non-lead,microgel based greases. Includes synthetic base oil, moly andmulti-season versions.
Recommended Applications:• Multi-purpose industrial and automotive• Where extreme temperatures and shock loading are
encountered• Including conveyors and pug mills of asphalt plants, ball mills
of ore crushing• Wheel bearings and chassis points
Advantages:• Synthetic XL 102M provides year round protection even at
extremely low and high temperatures• “ColourSense” indicator - grease changes colour from its
original blue as the temperature rises above 120°C. Colourchanges thru green , then to brown and finally to orange asthe temperature of the application rises. Useful to indicatepossible faulty equipment, excessively high temperatures anda need for more frequent regreasing.
• Superior high temperature performance and oxidationresistance
• Excellent load carrying ability• Excellent low temperature dispensability from the entire XL
family of greases• Compatibility with most other types of greases (thickeners)• Outstanding water resistance• Temperature range from -45 to 170°C
Approvals:• Darina XL greases meet NLGI GC/LB wheel bearing and
chassis requirements• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
GREASES
6.20
Darina XL - Premium Multipurpose Greases 3.75.11
GREASES
6.21
Prop
ertie
sD
ARI
NA
XL
GRE
ASE
S
Prod
ucts
102M
(Mol
y)EP
2EP
Mol
yM
ulti-
Seas
on
NLG
I Gra
de1
22
1
Prod
uct C
ode
504-
574
504-
554
504-
555
504-
556
Col
our
Gre
yBl
ueG
rey
Blue
Thic
kene
r Ty
peM
icro
gel
Mic
roge
lM
icro
gel
Mic
roge
l
Dro
ppin
g Po
int,
°C26
0+26
0+26
0+26
0+
Base
Oil
Type
Synt
hetic
Min
eral
Min
eral
Min
eral
Base
Oil
Visc
osity
, cSt
40°C
100
170
170
21
4 Ba
ll W
ear
Scar
, mm
0.6
0.5
0.5
0.5
4 Ba
ll EP
, Loa
d W
ear
Inde
x70
6060
55
Est.
Ope
ratin
g Ra
nge,
°C
-45
to 1
70-2
0 to
160
-20
to 1
60-4
0 to
80
Min
. Dis
pens
ing
Tem
p, °
C(m
ay v
ary
with
dis
pens
ing
syste
m)
-40
-10
-10
-35
Darina XL - Premium Multipurpose Greases 3.75.11
A grease for reducing rotating friction between drill rods andcasings.
Recommended Applications:• Outside of drilling rods, prior to insertion into the hole
Advantages:• Reduces friction and horsepower requirements• Increases drilling efficiency • Contains a germicidal agent to prevent infection of cuts
which may occur during handling of the drill rods
Properties DIAMOND DRILL ROD
NLGI Grade 3
Product Code 504-971
Colour Amber
Thickener Type Barium Sodium Complex
Base Oil Viscosity, cSt40°C 118
Dropping Point, °C 196
4 Ball EP, Load Wear Index 42
Est. Operating Range, °C -20 to + 120
GREASES
6.22
Diamond Drill Rod Grease - Drill Rod Lubricant
GREASES
6.23
Dursol K1 grease is designed to lubricate and protect valves inthe oil and gas resources industry which are exposed tocorrosive sour natural gas and oil.
Recommended Applications:• Valve bodies and stems of valves in sour (H2S containing)
natural gas pipeline and gas plant service
Advantages:• H2S corrosion protection• Base oils selected for year round low temperature valve
operation
Properties DURSOL K1 GREASE
NLGI Grade 1
Product Code 504-630
Colour Light green
Thickener Type Microgel
Dropping Point, C 260+
Base Oil Viscosity, cSt40°C 20
Est. Operating Range, °C -30 to 120
Dursol K1 - Sour Gas Valve Grease 3.60.02
A non-asphaltic, lead-free open gear lubricant which does notcontain any environmentally offensive solvents.
Recommended Applications:• Open gears as primarily found on mining shovels, draglines
and grinding mills• Malleus GL 25 may be used in certain enclosed gear cases -
propel transmissions, final drive gear boxes and hoist gearcases on mining shovels
• Plain and anti-friction bearings, pins and bushings on shovelcrawlers and boom assemblies
• Shovel sticks, swing gears, crowd pinions and racks, rollerpaths
• Malleus GL-95 is also available in an aerosol spray can
Advantages:• Synthetic and paraffinic base oils utilized to optimize
performance• Lead free• May be applied manually or via an automatic lube system• Malleus GL improves equipment availability and saves on
maintenance costs because it:• Stays soft and pliable to eliminate root build-up• Is fortified with molybdenum disulphide (Moly) and other
solid lubricants for a proper film structure with goodantiwear, EP, load carrying and shock loading protection
• Passes FZG +13 load stages• Minimizes cold metal contact welding• Resists contamination from other oils• Alleviates “stick slip” vibrations• Reduces consumption rates
Approvals:• Recognized for use by B.E., Marion, P&H,Allis Chalmers• Qualifies as P&H Multi-Service Mining Lubricant
GREASES
6.24
Malleus GL - Heavy Duty Open Gear Lubricant 3.84.04
GREASES
6.25
Prop
ertie
sM
ALL
EUS
GL
Gra
des
2565
95*
205
300
400
Prod
uct C
ode
504-
672
504-
676
504-
680
504-
684
504-
685
504-
669
Den
sity
@ 1
5.6∞
C1.
003
1.07
01.
076
1.08
01.
090
1.09
0
App
rox.
NLG
I gra
de00
\ 0
0000
\ 0
0000
\ 0
0000
\ 0
0000
0
Wor
ked
Pene
tratio
n @
25°
C (6
0x)
420+
420+
420+
420+
418
370
App
aren
t Vis
cosi
ty, c
P40
°C1,
675
2,25
06,
125
7,30
07,
060
36,7
5010
0°C
550
1,32
54,
000
6,10
01,
375
3,82
5
App
aren
t Vis
cosi
ty, c
P-1
°C-
--
--
--
-7,
900
- -
-18°
C2,
400
6,60
09,
400
20,5
0016
,000
12,5
00-4
0°C
13,7
5039
,000
- -
- -
- -
- -
4 Ba
ll W
ear
Scar
Dia
met
er, m
m0.
50.
60.
70.
70.
70.
7
4 Ba
ll EP
Wel
d Lo
ad, k
g50
062
080
080
080
080
0Lo
ad W
ear
Inde
x75
8511
012
013
116
6
Fale
x C
ontin
uous
Loa
d Fa
ilure
, kg
+ 20
45+2
045
+204
5+2
045
+204
5+2
045
Est.
Low
Tem
p. D
ispe
nsin
g, °
C-4
0-3
0-1
00
+7+1
0
Malleus GL - Heavy Duty Open Gear Lubricant 3.84.04
* A
vaila
ble
in a
eros
ol s
pray
can
, Pro
duct
Cod
e 50
4-68
8.
Lead free high pressure thread compound to aid in joining andseparating threaded connections.
Recommended Applications:• Casing and tubing connections in the oil and gas industry• Metallic tubulars with A.P.I. 8 Round, LTC and EUE thread
profiles• Other general threading applications
Advantages:• Lead free for health and safety protection• Superior H2S corrosion inhibitors• Protects against seizures or galling (adhesion) of the threaded
contact surfaces• Thread sealing pressure tested to 7,500 PSI• Ease of application for year round usage
Approvals:• Meets or exceeds A.P.I. Bulletin 5A2
Properties MALLEUS TC
Product Code 504-598
Colour Silver \ Grey
Specific Gravity 1.629
Composition 55 % solids
Penetration @ 25°C 312 - 332
NLGI grade 1
Dropping Point of Base, °C 299
API Brushing AbilityApplicable at, °C -23
Torque Correction Factor 0.95
GREASES
6.26
Malleus TC - High Pressure Thread Compound 3.63.04
GREASES
6.27
A semi-fluid, non EP, Moly grease for centralized lubricationsystems.
Recommended Applications:• Railway locomotive wheel flange and rail lubrication via on-
board lubricators• Lightly loaded gear boxes requiring a semi-fluid grease. Also
see Shell Surstay EP 000• Centralized lubrication systems operating at low temperatures• Including trucks, buses, manufacturing machinery
Advantages:• Rust and oxidation inhibited• Excellent low temperature pumpability / mobility• Water resistant• Carries well along railway rails
Approvals:• Meets the requirements of Canadian National Railways,Willy
Vogel
Properties OSSAGOL C MOLY
NLGI Grade 00
Product Code 504-512
Colour Grey
Thickener Type Calcium Soap
Dropping Point, °C 137
Base Oil Viscosity, cSt40°C 27
Est. Operating Range, °C(may vary with dispensing system) -40 to 80
Mobility @ -30°C, g/min 114
Ossagol C Moly - Semi Fluid Grease 3.49.07
GREASES
6.28
A premium, synthetic, semi-fluid, EP grease for truck wheel hubs.
Recommended Applications:• Truck wheel hubs / trailer wheel bearings• Leaky gearboxes or gear units that are difficult to service.
Verify that the base oil viscosity is appropriate.• Guidelines for use in wheel hubs can be found in The
Maintenance Council (TMC) practice RP 631
Advantages:• Synthetic base oil provides good low temperature pumping in
centralized systems, compared to mineral oil of similarviscosity
• Significantly reduces leakage relative to gear oil• Heavy base oil viscosity and EP additives provide wear and
shock loading protection• Provides rust protection and excellent oxidation stability• Natural tacky nature toward metal surfaces
Properties RETINAX TL 00
NLGI Grade 0 / 00
Product Code 504-820
Appearance Red
Thickener Type Lithium Complex
Base Oil Viscosity, cSt40°C 460100°C 41.5
Timken OK Load, kg 22.7
4 Ball EPWeld Load, kg 250Load Wear Index, kg 46
Est. Operating Range, °C -40 to 170Short Exposure, Max., °C 230
Retinax TL 00 - Trailer Wheel and Hub Lubricant
GREASES
6.29
Our most water resistant, multi-purpose grease for use in heavyduty applications.
Recommended Applications:• Heavy duty on and off highway equipment• Logging, construction, agricultural and forestry equipment• Car washes• Marine applications• Fifth wheels, pins, bushings, slack adjusters, chassis points,
pulley bearings, couplings,“cups and saucers”
Advantages:• Outstanding heavy duty water resistant protection• Synthetic and other high performance components• Moly and low temperature winter versions• Protects against vibration and shock loading• Outstanding mechanical stability• Excellent adhesion (tackiness)• Superior oxidation resistance provides long performance life
Approvals:• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
GREASES
6.30
SRS 2000 - Water Resistant Grease
GREASES
6.31
Prop
ertie
sSR
S 20
00
Prod
uct
Sum
mer
Mol
y (5
%)
Sum
mer
Win
ter
Win
ter
Mol
y (5
%)
NLG
I Gra
de2
1.5
11
Prod
uct C
ode
510-
333
510-
332
510-
334
510-
335
App
eara
nce
/ C
olou
rTa
cky
/ G
rey
Tack
y /
Red
Tack
y /
Red
Tack
y /
Gre
y
Thic
kene
rLi
thiu
m/C
alci
umLi
thiu
m/C
alci
umLi
thiu
m/C
alci
umLi
thiu
m/C
alci
um
Dro
ppin
g Po
int,
°C18
318
317
817
8
Base
Oil
Visc
osity
, cSt
40°C
Ble
nded
171
171
2929
40°C
Ext
ract
ed40
060
035
3510
0°C
Ext
ract
ed27
.737
.25.
45.
4
Tim
ken
OK
Load
, kg
36.4
18.2
18.2
22.7
4 Ba
ll W
ear,
mm
0.4
0.5
0.5
0.4
4 Ba
ll EP
, Wel
d Lo
ad, k
g40
031
531
540
0
Est.
Ope
ratin
g Ra
nge,
°C
(m
ay v
ary
with
dis
pens
ing
syste
m)
-15
to 1
35-1
5 to
135
-40
to 8
0-4
0 to
80
Min
Dis
pens
ing
Tem
p, °
C0
0-3
5-3
5
Wat
er W
asho
ut T
est,
% w
t los
s3
510
10
SRS 2000 - Water Resistant Grease
A semi-fluid, EP grease for enclosed heavy-duty gear boxapplications.
Recommended Applications:• Rotor drive gear boxes of Marietta Miners in potash mining• Drive gear boxes of conveyor systems• Gear boxes where leaking bearing seals make the use of a
thickened oil desirable• NOT recommended for centralized lubrication pumping
systems. In these applications, Ossagol *C Moly or Alvania EPArctic are recommended.
Advantages:• Extreme pressure, antiwear and shock loading protection• Excellent stability - maintains thickness without thinning or
thickening• Tenaciously adheres to gear and bearing surfaces to prevent
dry start-up• Excellent seal compatibility
Properties SURSTAY EP 000
NLGI Grade 000
Product Code 504-988
Colour Brown
Thickener Type Microgel
Dropping Point, °C 260+
Base Oil Viscosity, cSt40°C 184
4 Ball Wear, mm 0.5
4 Ball EP,Weld Load, kg 250Load Wear Index 47
Est. Operating Range, °C -10 to 130
GREASES
6.32
Surstay EP - Semi Fluid Grease 3.67.02
A synthetic grease for extremely high temperatures.
Recommended Applications:• Plain and rolling element bearings• Run-out table rolling bearings in steel mills• In mines, mills, boiler plants• In pulp and paper, saw mills• In cement and lime plants• NOT suitable for high speed or low temperature applications
due to the high viscosity base oil used• Prior to use, bearings should be thoroughly cleaned of
conventional greases
Advantages:• Outstanding high temperature resistance• Suitable up to 250°C with frequent relubrication• Superior mechanical stability against high shears and
pressures
Properties ULTRAGEL
NLGI Grade 2
Product Code 504-560
Appearance / Colour Very Tacky/Amber (clear)
Thickener Type Inorganic
Dropping Point, °C +343
Base Oil Viscosity, cSt40°C 7,500
Timken OK Load, kg 27.2
Max. Operating Temperature, °C 250
Min. Dispensing Temp, °C(may vary with dispensing system) +20
GREASES
6.33
Ultragel - High Temperature Grease 3.58.04
6.34
Page
Biodegradable (Hydraulic Oils)Shell Naturelle HF-E . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.32Shell Naturelle HF-M . . . . . . . . . . . . . . . . . . . . . . . . . . 7.33
CompoundedValvata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.60
CompressorAir: Corena P . . . . . . . . . . . . . . . . . . . . . . 7.16
Corena DE . . . . . . . . . . . . . . . . . . . . . 7.12Corena AS . . . . . . . . . . . . . . . . . . . . . . 7.10Corena S. . . . . . . . . . . . . . . . . . . . . . . 7.18
Natural Gas: Corena NG . . . . . . . . . . . . . . . . . . . . . 7.14Refrigeration: Clavus . . . . . . . . . . . . . . . . . . . . . . . . 7.6
Clavus AB . . . . . . . . . . . . . . . . . . . . . . 7.7Clavus HFC 68 . . . . . . . . . . . . . . . . . . 7.8
ElectricalDiala . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.22
Food GradeShell Fluid FM 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3
Form (Concrete)Form Oil 46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.25
FlushingCassis A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4
GearOmala . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.38Geartherm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.27Omala HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.40Omala RL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.41Tivela. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.53Hyperia S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.28
Heat TransferThermia C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.52
Hydraulic / CirculatingTellus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.46Tellus T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.50Tellus HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.48Tellus 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.45Decol H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.19Morlina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.30No Fire WG 200R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.36Shell FR-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.34VSI 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.62
INDUSTRIAL OILS
7.1
Table of Contents
IND
USTR
IAL O
ILS
Page
Machine ToolTonna V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.54
Metalworking / Cutting OilsDromus B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.24Garia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.26
Mineral OilsVitrea 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.61Pella A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.42Shellflex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2, 9.4
Natural Gas EngineMysella . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.31
Non-DripStringol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.44
Paper MachineDelima. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.20Delima R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.21
Refrigeration - see Compressor
Rock DrillTorcula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.56
Rust PreventativeVSI 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.62
SawguideSawguide Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.43
SolventShell Indusol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.29
SpindleTellus 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.45
TurbineShell Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.58
White Oil - see Food Grade
Wire RopeClasslube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5
INDUSTRIAL OILS
7.2
Table of Contents, continued
INDUSTRIAL OILS
7.3
A mineral based white oil for use in food processing equipment.
Recommended Applications:• Mold release oil in bakery applications• Carrier in cosmetics and medicinal products• Food essences and flavouring substitutes• General purpose lubricant for applications where the
lubricant may directly contact food being processed
Advantages:• Multi-purpose - a white oil suitable as a lubricant as well as a
food and cosmetic ingredient
Approvals:• Satisfies the requirements of U.S. Department of Agriculture
(USDA), FDA,Type H1 (incidental food contact)• Pass United States Pharmacopoeia (USP) specification• Approved for the requirements of the Canadian Food
Inspection Agency (CFIA),Type n3 (protective coating oils),for registered meat packaging plants
• 3-GP-46A• 3-GP-46M
Properties SHELL FLUID FM
Grades 32
Product Code 407-961
Colour, Saybolt +30
Viscosity, cSt40°C 37
Pour Point, °C -6
Flash Point, °C 188
Aniline Point, °C 105
Shell Fluid FM 32 - Food Grade White Oil 3.25.09
A mineral oil-based product for flushing / cleaning the internalcomponents of equipment and machinery.
Recommended Applications:• Flushing circulation systems, gearboxes and other equipment
to remove rust preventatives, dirt, construction debris andwater prior to service or in older equipment which simplyrequires cleaning
• Including paper machines, marine, and manufacturing plants• Cassis A should be properly disposed after the flushing
procedure• Caution - Cassis A will attack and/or remove some paints
Advantages:• Select base oils and solvents• Rust inhibited• Highly solvent flushing oil• Penetrating action• Safe at elevated temperatures (60 - 70°C) used for best
flushing
Approvals:• Meets MIL-C-15348A Amendment 2• Meets 3-GP-354A
Properties CASSIS A
Grades 32
Product Code 407-950
Viscosity, cSt40°C 28.0100°C 4.6
Pour Point, °C -33
Flash Point, °C 132
TAN - C 0.2
INDUSTRIAL OILS
7.4
Cassis Oil A - Flushing Oil 3.24.07
Shell Classlubes are free flowing oils, fully blended to inhibitrust, oxidation and wear.
Recommended Applications:• Wire Rope Lubricants on friction hoist ropes• Any type of conveyor, chain drives• Applications where ‘tacky’ oils are required
Advantages:• Free flowing oils blended from HVI base stocks• Formulated to inhibit oxidation and wear• Unique dual anti-rust additive system provides extra rust
protection under corrosive conditions• Fortified with a tackifier to provide adhesion of the lubricant
to wire ropes, chains, conveyors• ISO 32 grade available in aerosol cans for ease of application• Dyed red for easy identification
Properties CLASSLUBE
Grades 32 320
Product Code 407-201 407-203
Appearance Tacky Tacky
Colour Red Red
Viscosity, mm2/s40°C 32 315100°C 5.8 25
Viscosity Index 124 102
Pour Point, °C max. -27 -15
Rust (Syn. Sea Water) Pass Pass
4-Ball Wear TestScar diameter, mm 0.50 0.41
INDUSTRIAL OILS
7.5
Classlube - Cable and Wire Rope Lubricant
Mineral oil based refrigeration compressor oil.
Recommended Applications:• Refrigeration compressor oil• Suitable for, and compatible with CFC (Freon* 12,
Freon* 22 etc.) and ammonia refrigerant gases withevaporator temperatures down to -45°C
• NOT recommended for use with newer HFC gases such as R-134A and R-23
Advantages:• Wax free, naphthenic base oils (low floc point)
provide outstanding low temperature performance• Oxidation stability at high temperatures resists
deposit formation• Excellent chemical stability and compatibility
Approvals:• Meets or exceeds the requirements of most
compressor builders
Properties CLAVUS OIL
Grades 68
Product Code 407-942
Viscosity, cSt40°C 55.0100°C 5.88
Pour Point, °C max -35
Floc Point, °C -45
Flash Point, °C 179
Aniline Point, °C 88
Dielectric Strength, KV 30
INDUSTRIAL OILS
7.6
Clavus Oil - Refrigeration Compressor Oil 3.95.01
INDUSTRIAL OILS
7.7
Synthetic refrigeration compressor oils for conventional lowtemperature refrigerants.
Recommended Applications:• All refrigeration compressor types including reciprocating,
centrifugal and rotary• Compatible with ammonia, CFC and HCFC refrigerant gases
with evaporator temperatures below -45°C• Including R12, R13, R22, R114, R123, R124, R401A, R401B,
R401C, R402A, R402B, R403, R500, R502, R503 refrigerants inboth industrial and marine applications
• NOT recommended with HFC gas R-134A. See Shell ClavusHFC 68.
Advantages:• Special alkylated synthetic base stocks• Extended service life and longer drain intervals• Outstanding low temperature properties - no deposit
formation• Excellent high temperature stability• Eliminates degradation and sludging• Prevents fouling of heat transfer surfaces, evaporators and
valves• Improved wear protection• Compatible with conventional mineral oils and materials such
as Mylar*, polypropylene,Viton*, Buna-N, Neoprene*, and nylonelastomers
• Improved compressor efficiency• High degree of chemical stability• Improved resistance to foaming
Properties CLAVUS AB OILS
Grades 32 68
Product Code 407-681 407-682
Viscosity, cSt40°C 33 65100°C 4.1 5.6
Pour Point, °C -45 -35
Floc Point, °C -65 -55
Flash Point, °C 150 165
Dielectric Strength, KV 30 30
Clavus AB - Synthetic Refrigeration Compressor Oils 3.96.03
7.8
Synthetic refrigeration compressor oils for newer HFC (chlorinefree, environmentally friendly) refrigerants such as R-134A, aswell as for conventional CFC or Freon* based refrigerants.
Recommended Applications:• Automotive air conditioning and industrial and mobile
refrigeration units with compressors that are designed for, orhave been converted to using R-134A, HFC refrigerants
• Compressors using CFC or Freon* refrigerants as well asblended HFC refrigerants
Advantages:• No miscibility problems with R134A refrigerants• Suitable for plants with both new and older refrigerants in use
and wishing to consolidate lubricants• Compatible with mineral oils, although mixing will adversely
affect performance• Compatible with elastomers of Buna-N, NBR-Acrylonitrile-
Butadiene, HNBR-Hydrogenated Acrylonitrile-Butadiene(Nitrile content >32%),Viton* and Teflon*
• Suitable over a wide temperature range, -57°C to +66°C• Improved lubricity• Excellent stability• Reduced compressor wear• Increased hydrolytic stability in the presence of water
Properties CLAVUS HFC 68
Grades 68
Product Code 407-683
Viscosity, cSt40°C 68100°C 8.6
Pour Point, °C -54
Flash Point, °C 248
TAN 0.02
Critical Solution Temp, °CR-12 < -56.7R-22 < -56.7R134A < -56.7R404A < -56.7
Clavus HFC 68 - Synthetic Refrigeration Compressor Oils 3.97.02
INDUSTRIAL OILS
INDUSTRIAL OILS
7.9
INDUSTRIAL OILS
7.10
A high performance synthetic lubricant for oil-flooded vane andscrew air compressors.
Recommended Applications:• Rotary oil-flooded vane and screw type air compressors• Heavy duty, single or multi-stage equipment operating with
high discharge temperatures operating at high or low ambienttemperatures
• Reciprocating air compressors should use Shell Corena DE(synthetic) or Shell Corena P (mineral oil)
Restrictions in Use:• Shell Corena AS should not be used in reciprocating
compressors, or in drip-feed rotary compressors which havedifferent lubrication requirements and compressors used forbreathing air.
Advantages:• Will reduce maintenance costs over operation on
conventional mineral oils• Utilizes synthetic PAO (poly-alpha-olefin / synthetic
hydrocarbon) base oils• Long oil life - up to eight times that of mineral oils• Ultimate performance beyond the scope of mineral based oils• Low volatility - less oil consumption and make-up required• Resistance to oxidation and the deposits it creates• Good low temperature performance• Excellent demulsibility• Compatible with mineral oils and common oil seal materials
Approvals:• Approved for the requirements of the CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
Corena AS - Synthetic Air Compressor Oil 3.98.01
Properties CORENA AS
Grades 46 68
Product Code 407-943 407-944
Viscosity, cSt40°C 42.3 69.5100°C 7.3 12.4
Viscosity Index 136 180
Low Temp. Viscosity, cSt-18°C 1,470 2,200-29°C 4,500 6,500
Pour Point, °C -54 -45
Flash Point, °C 277 260
Fire Point, °C 307 277
Autoignition Point, °C 400 400
CCR residue, % < 0.01 <0.01
INDUSTRIAL OILS
7.11
Corena AS - Synthetic Air Compressor Oil 3.98.01
Formerly Corena AP oils.A high performance diester syntheticoil for reciprocating air compressors.
Recommended Applications:• Stationary or mobile reciprocating air compressors• Heavy duty, single or multi-stage equipment operating with
high discharge pressures (over 30 bar, 435 psi) and highdischarge temperatures (over 180°C)
• Compressors operating at high or low ambient temperatures• May be used to compress air for breathing purposes provided
strict conditions are adhered to - including proper subsidiaryair clean-up apparatus downstream of compressor*
• New equipment run-in (first 1,000 hours) should use ShellCorena P Oils
• Rotary air compressors should use Shell Corena AS (synthetic)or Shell Tellus Oil (mineral)
*Restrictions in Use:• This product should not be used in non-diaphragm
compressors that produce breathing air unless the outlet air ismonitored continuously for CO.These lubricants can produceCO when subjected to high temperatures.
Advantages:• Safety - greatly reduces the danger of fires and explosions
which can occur from deposits caused by mineral based oils• Ultimate performance beyond the scope of mineral based oils• Resistance to oxidation and the deposits it creates• Will reduce maintenance costs over conventional mineral oils,
extending valve maintenance intervals 4 - 8 times• Low volatility - less oil consumption and make-up required• Good low temperature performance• Good demulsibility• Compatible with Viton*, fluorosilicone, polysulfide and high
nitrile Buna-N elastomers• Not compatible with Neoprene*, natural rubber, SBR styrene-
butadiene rubber (Buna-S) or low nitrile Buna-N seals,polycarbonate filter bowls, some paint
INDUSTRIAL OILS
7.12
Corena DE - Synthetic Air Compressor Oil 3.99.01
Properties CORENA DE
Grades 68 100
Product Code 407-684 407-680
Viscosity, cSt40°C 68.3 98.8100°C 8.9 9.7
Low Temp. Viscosity, cSt-18°C 9,085 32,530
Pour Point, °C -42 -33
Flash Point, °C 266 266
Fire Point, °C 288 288
Autoignition Point, °C 410 410
CCR residue, % 0.04 0.01
INDUSTRIAL OILS
7.13
Corena DE - Synthetic Air Compressor Oil 3.99.01
INDUSTRIAL OILS
7.14
Premium, partially synthetic, cylinder and packing oil primarilyfor sour and/or wet natural gas reciprocating compressors.
Recommended Applications:• Applied via oil injection systems into cylinders and packings
of reciprocating compressors in sour (H2S) and wet (water orhydrocarbon) service
• 220 grade provides protection in cylinders with dischargepressures up to 14,000 kPa (2,000 PSI)
• 460 grade provides protection in cylinders with dischargepressures up to and beyond 28,000 kPa (4,000 PSI)
• Propane compression with suction temperatures down to -30°C• Compressing chemical gases such as aldehydes and keytones• For compressor crankcases of this type use Shell Mysella Oils
Advantages:• Non-fatty formulation eliminates deposits in the injection
system• Not sensitive to freezing• Superior low temperature flow properties• Resistant to wash-off from cylinder walls in wet service• Excellent oxidation resistance and valve/rod cleanliness• Corrosion protection against H2S and rusting from water
Approvals:• Meets requirements of Dresser Rand, Cooper Energy Services
and others
Properties CORENA NG
Grades 220 460
Product Code 407-238 407-239
Viscosity, cSt40°C 211 422100°C 17.9 28.4
Pour Point, °C -24 -18
Brookfield Viscosity, cP0°C 4,300 12,000-10°C 13,800 - --15°C 27,400 - -
Est. Lowest Suction Temp, °C -30 -15
Flash Point, °C 268 282
Corena NG - Reciprocating Compressor Cylinder and Packing Oil 3.71.04
INDUSTRIAL OILS
7.15
INDUSTRIAL OILS
7.16
Mineral oil based air compressor oils for reciprocating compressors
Recommended Applications:• Industrial and marine reciprocating air compressors• Including single and multistage units with trunk or crosshead
piston designs• Including crankcases of oil-free designs• Including cylinder oils for machines with separate oil
injection systems• Suitable for discharge temperatures of 160°C and up to 200°C• Corena P oils should never be used in equipment
compressing pure oxygen
Restrictions in Use:• This product should not be used in non-diaphragm
compressors that produce breathing air unless the outlet air ismonitored continuously for CO.These lubricants can produceCO when subjected to high temperatures.
Advantages:• Selected base stocks for exceptional resistance to deposit
formation• Safety from fires and explosions caused by deposit formation• Reduced equipment maintenance• 122 grade replaces both ISO 100 and 150• Compatibility with seals, other mineral based oils and some
synthetics• Rust and corrosion protection• Anti-wear protection• Good demulsibility from water• Performance rivals synthetic oils in all but the most severe
applications without the problems of seal compatibility, cylinderwear, corrosion and odour associated with some synthetics
Approvals:• Meets ISO-L-DAB (medium duty service at temperatures
between 140°C and 160°C)• Recommended for Atlas Copco, Compair, Broomwade and
Reavell, Ingersol Rand and others
Corena P - Air Compressor Lubricants 3.79.03
Properties CORENA P
Grades 68 122 220
Product Code 407-226 407-240 407-230
Viscosity, cSt40°C 69 123 220100°C 8.2 11.7 18.2
Viscosity Index 83 80 91
Pour Point, °C -33 -27 -15
Flash Point, °C 228 230 292
Fire Point, °C 262 278 318
INDUSTRIAL OILS
7.17
Corena P - Air Compressor Lubricants 3.79.03
Corena S is a mineral oil based, rust and oxidation (R&O)inhibited oil.
Recommended Applications:• Rotary screw and vane compressors requiring a rust and
oxidation inhibited oil in an ISO 32 grade• Circulating systems requiring an R&O oil• Hydraulic systems requiring an R&O type oil (low pressure)• Plain and rolling element bearings in pump crankcases• For heavier viscosity grades see Shell Morlina Oils
Advantages:• Outstanding oxidation resistance• Specially processed and handled to enhance water separation
and air release• Excellent rust protection
Approvals:• Meets Cincinnati Milacron P-38 specification for “Rust and
Oxidation Inhibited Hydraulic Oils”
Properties CORENA S
Grades 32
Product Code 407-225
Viscosity, cSt40°C 32100°C 5.4
Viscosity Index 102
Pour Point, °C -30
INDUSTRIAL OILS
7.18
Corena S - Premium R & O Compressor Oil
General purpose anti-wear hydraulic oils.
Recommended Applications:• Industrial and mobile hydraulics• Suitable for all types of hydraulic pumps• Circulating systems in place of R&O type oils• For high performance state-of-the-art hydraulic systems, Shell
Tellus and Tellus T Oils are recommended
Advantages:• Cost effective performance• Wear protection • Long oil life• Rust and oxidation inhibited
Approvals:• Meets Vickers 104C vane pump test pass• Meets Vickers 35VQ25 vane pump test pass• Meets Denison P46 axial piston pump test pass
Properties DECOL H
Grades 22 32 46 68
Product Code 407-736 407-737 407-738 407-739
Viscosity, cSt40°C 20.8 31.9 46.3 68.5100°C 4.27 5.4 6.8 8.8
Viscosity Index 99 100 98 100
Pour Point, °C -27 -27 -24 -24
Flash Point, °C 210 217 238 247
INDUSTRIAL OILS
7.19
Decol H - General Purpose Hydraulic Oils 3.64.07
A leading edge technology, detergent-dispersant type papermachine oil. Intended to set the standard for the industry.
Recommended Applications:• Paper machine oil circulation systems, dry and wet ends, as
well as individually lubricated bearings• Including high speed newsprint machines, high temperature
kraft and board machines• Including rolling and Kingsbury type bearings, centrifugal
pumps, vacuum and water pumps, blowers, reduction gears,main drive shaft winder and rewinders etc.
Advantages:• Rapid water separation from “white water”• New detergent technology• Filterability when contaminated with water, Passes Pall test• Mild EP and wear protection, passes FZG load stage 12• High temperature and oxidation stability• Rust and corrosion protection• Resistance to foaming
Properties DELIMA OILS
Grades 150 220 290 460
Product Code 407-821 407-823 407-825 407-826
Viscosity, cSt40°C 151 220 290 457100°C 15.0 18.9 22.9 30.6
Viscosity Index 94 96 96 95
Pour Point, °C -18 -15 -12 -12
Flash Point, °C 265 288 288 292
INDUSTRIAL OILS
7.20
Delima - Paper Machine Oil 3.05.10
A unique premium oil for Sunds defibrator refiners as used inthe pulp and paper industry.
Recommended Applications:• Sunds defibrator refiner lubrication
Advantages:• Excellent extreme pressure and anti-wear protection• Prevents erosion on the piston by the seals and subsequent oil
leakage• Excellent water separation and performance in the presence
of water• Good filterability performance designed to result in cleaner
systems and lower filter costs• Designed to effectively release air and dispel foam• Excellent corrosion protection for the steel and bronze
components used in Sunds refiners. Passes SKF Roller BearingTest with no discolouration of the rollers.
Approvals:• Approved for use by Sunds Defibrators
Properties DELIMA R 68
Grades 68
Product Code 407-828
Viscosity, cSt40°C 69100°C 8.7
Viscosity Index 97
Pour Point, °C -30
Flash Point, °C 242
4 Ball EP, Weld Load (kg) 305
4 Ball EP, OK Load (kg) 285
INDUSTRIAL OILS
7.21
Delima R - Sunds Defibrator Refiner Oil 3.06.01
Naphthenic electrical insulating oils, with and without anti-oxidant additives.
Recommended Applications:• Transformers, circuit breakers, oil-filled switches, X-ray
equipment• Capacitors (condensers) and oil insulated cables• Heat transfer medium• Spindle oil in high speed bearings• Diala A for Class B,Type I applications (non-anti-oxidant)• Diala AX for Class B,Type II applications (which require an
anti-oxidant)
Advantages:• Excellent electric insulation and heat transfer properties• Do not contain any polychlorinated biphenyls (PCB’s)• Low pour point• Oxidation stability to resist acid formation• Diala Oils are specially handled and packaged to prevent
minute contamination by moisture, particulate, fibres andsurfactants. Storage should be indoors, in air-tight containers,in a climate-controlled environment
Approvals:• Meets ANSI / ASTM D-3487• Meets NEMA TR-P8-1975• GE spec A13A3A2 (10CA)• Westinghouse PD 55822 AV rev.T-WEMCO CI• US Military spec VV-I-530a and Amendment 2 for Class I (Type
I)and Class II (Type II) fluids. Supersedes Dept of Navy specOS-1023.
• NATO symbol S-756, covered by British Standard BS 148:1972• Diala AX is approved for the requirements of CFIA (Canadian
Food Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
INDUSTRIAL OILS
7.22
Diala - Electrical Insulating Oils 3.17.05
Properties DIALA OILS
Grades Diala A / AX
Product Code 407-652 / 407-651
Viscosity, cSt0°C 6640°C 9.3100°C 2.6
Pour Point, °C -47 to -55
Flash Point, (COC) °C 155
Interfacial Tension @ 25°C, Dynes/cm 47
Dielectric Strength @ 60 Hz:DISC electrodes, Kv 51VDE electrodes (1.02 mm gap), Kv 34
Power Factor, % @ 100°C 0.03/0.04
Aniline Point, °C 76
TAN-C < 0.01
Gassing Tendency µL/min. 12
INDUSTRIAL OILS
7.23
Diala - Electrical Insulating Oils 3.17.05
Premium soluble oil for making oil-in-water emulsions used incutting / metalworking operations.
Recommended Applications:• Cutting applications where cooling is essential to the
operation• Sawing, plain milling and grinding operations• Boring and turning of some steels• Quenching induction heated parts• Roll coolant• As a corrosion inhibitor in hydraulic systems where water is
the hydraulic fluid• Should NOT be used on metals containing magnesium• See our “Lubricants Report” for preparation and fluid
maintenance instructions. Dromus B is sensitive to “freeze-thaw” exposure, please store appropriately.
Advantages:• Built-in biocide• Excellent rust protection• Better aluminum compatibility due to lower pH• Outstanding freeze/thaw stability• No chemical, toxicological or irritation hazards
Properties DROMUS B
Product Code 407-776
Base Oil Viscosity, cSt40°C 80
Base Oil Flash Point, °C 162
pH (10% Emulsion) 8.7
INDUSTRIAL OILS
7.24
Dromus B - Soluble Cutting Oil 3.11.08
Release agent for wooden concrete construction forms.
Recommended Applications:• Specifically designed for wooden forms used in concrete
pouring operations• Also suitable for metal and plastic forms used in concrete
construction• Sprayed, swabbed, or brushed onto forms• May be cut-back with kerosene as required. 10% kerosene is a
good initial mix
Advantages:• Mineral and fatty oils provide easy release of the wood from
the concrete• Smooth quality surface finish on concrete• Reduced wear and prolonged form life
Properties FORM OIL 46
Grade 46
Product Code 407-632
Viscosity, cSt40°C 45100°C 6.1
Viscosity Index 72
Pour Point, °C -30
Flash Point, °C 164
TAN-E 5.6
INDUSTRIAL OILS
7.25
Form Oil 46 - Concrete Form Release Agent 3.47.04
Two “Active” sulphur and chlorine containing, EP cutting /metalworking oils for ferrous metals which are moderate todifficult to machine.
Recommended Applications:• Garia D for multi-spindle work, gear cutting, thread grinding,
tapping and threading, thread rolling and broaching of hightensile steels and stainless and heat resistant alloys
• Garia T for Deep-hole Boring / Drilling using various Systems,high-speed hobbing gear shaping, broaching and for use withskiving and roller burnish tooling systems of low, medium andhigh tensile steels and stain resistant and heat resistant alloys
• NOT recommended for machining “yellow” metals• NOT to be used as a hydraulic medium• Plain milling, sawing and grinding operations should use Shell
Dromus B soluble cutting oil
Advantages:• Active EP type additive system provides improved cutting
efficiency, better surface finish and tool life• Viscosity selected to lubricate the cutting interface and wash
away chips. Garia D’s viscosity is designed to reduce “drag-out” while Garia T is designed for precision grinding
• Garia T does not lose its active ingredients or form sludgeunder severe filtration (10 micron) required for deep holeapplications
• Garia D may stain non-ferrous and yellow metals• NOT to be mixed with water to form cutting emulsions
Properties GARIA
Product Garia D Garia T
Product Code 407-801 407-798
Viscosity, cSt40°C 32 15100°C 4.7 2.9
Pour Point, °C ‡ ‡
Flash Point (COC), °C Min 160 127
Sulphur Content, % mass 0.89 1.04
Chlorine Content, % mass 0.92 4.1
‡ Do Not Store Below 0°C
INDUSTRIAL OILS
7.26
Garia - Neat Cutting Oils 3.08.01
Mineral based, multigraded industrial gear oils. Geartherm Oilsare all-season (low temperature, multigrade) versions of ShellOmala Oils.
Recommended Applications:• Enclosed industrial gearboxes which may be started or
operated in cold environments• Rolling bearings in pump crankcases
Advantages:• Year-round performance• AGMA EP - excellent load carrying ability and protection
against shock loading• “Stay-in-Grade” viscosity performance• Improved rust and corrosion protection• Anti-foam protection• Good water separation capability• For a full synthetic industrial gear oil see Shell Omala HD Oils
Approvals:• Hydro Quebec PAEM 89204
Properties GEARTHERM
Products Arctic AS Multigrade 150
ISO Grade 68 150
AGMA Grade 2EP 4EP
Product Code 407-537 407-539
Viscosity, cSt40°C 64.3 151100°C 9.84 18.7
Viscosity Index 135 140
Brookfield Visc., cP-20°C - - 19,300-26°C 17,083 62,985-30°C 38,500 143,167-36°C 150,000 - -
Pour Point, °C -39 -33
Flash Point, °C 174 216
Channel Point, °C < -50 -45
Max. Typical Oil Operating Range, °C -36 to 45 -30 to 70
INDUSTRIAL OILS
7.27
Geartherm Oils - Premium All-season Industrial Gear Oils 3.65.07
A full synthetic industrial EP gear oil.
Recommended Applications:• Specifically for General Electric wheel motors• For a full line of full synthetic industrial EP gear oils see Shell
Omala HD
Advantages:• Full synthetic (PAO) base oils for excellent low temperature
properties in a heavy ISO 220 gear oil.• Improved equipment reliability and reduced equipment
operating costs• Energy savings from improved efficiency
Approvals:• GE 787 and GE 788 for motorized wheels
Properties HYPERIA S
Grades 220
AGMA Grade 5 EP
Product Code 407-523
Viscosity, cSt40°C 222100°C 26.0
Viscosity Index 162
Brookfield Viscosity, cP@ -38°C 150,000
Pour Point, °C -48
Channel Point, °C < -50
Flash Point, °C 263
INDUSTRIAL OILS
7.28
Hyperia S - Synthetic Industrial Gear Oil 3.80.04
A conventional mineral spirits industrial solvent.
Recommended Applications:• Cleaner• Diluent• Degreaser• Agent in surface coatings, waxes and polishes
Advantages:• Interchangeable with all Stoddard solvents• Traditional solvency and evaporation rate• Available in 205 litre drums
Approvals:• CAN 2-3.8-M85• ASTM D-235-77• 1-GP-4M Ref 12080-M• P-D-680 AM.2 Type 1• TT-T-291e AM.1 Type 1 GrA
Properties SHELL INDUSOL
Product Code 482-100
Density 786
Flash Point, °C (Tag CC), min. 42
Aniline Point, °C 55
Kauri Butanol Value 39
Distillation Range, °C 158 - 193.5
Sulphur Content, mg/kg (ppm) < 1
INDUSTRIAL OILS
7.29
Shell Indusol - Industrial Hydrocarbon Solvent 5.08.02
Premium, medium / high viscosity rust and oxidation oils forcirculating systems.
Recommended Applications:• Circulating systems requiring heavier viscosity rust and
oxidation oils• Hydraulics, gears and bearings where a thicker, non-EP,
non-anti-wear oil is required. Systems not prone to wear,high loads or shock loading
• Gear systems with internal backstops where anti-wear/EP additives can cause equipment (conveyors) to creep under load
• For lower viscosity grades see Shell Turbo T Oils
Advantages:• High rust and oxidation resistance• Superior demulsibility from water• Low foaming tendency
Approvals:• Recommended or approved for use by Alpha Laval, Falk,
Danielli• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
Properties MORLINA
Grades 150 220 320
Product Code 407-881 407-882 407-883
Viscosity, cSt40°C 152 220 316100°C 14.9 18.9 24
Viscosity Index 97 97 97
Pour Point, °C -18 -12 -12
Flash Point, °C 283 290 306
INDUSTRIAL OILS
7.30
Morlina - R & O Circulating Oil 3.12.02
INDUSTRIAL OILS
7.31
Recommended Applications:• Stationary natural gas engine oils• Mysella 40 is an ashless oil for 2 stroke engines• Mysella LA30 and LA 15W-40 are low ash oils for 4 stroke
engines• Mysella MA40 is a medium ash oil intended for most
Waukesha and White Superior engines• See our “Lubrication Report” for specific application details• Also used in natural gas compressor crankcases• Cylinders and packings in dry and sweet gas service• Most pump crankcases
Advantages:• Three ash levels• Ashless (and low ash) blended to reduce port blockage• Premium anti-wear, rust and oxidation and detergency
additives• Compatible with NSCR catalysts• Improved nitration resistance• Multigrade for improved low temperature start-ups
Approvals:• Mysella LA30, LA 15W-40 and MA40 meet API CD • Mysella MA40 approved for Waukesha Cogeneration
applications
Properties MYSELLA
Grades 40 LA30 LA15W-40 MA40
Product Code 407-177 407-173 407-176 407-174
Viscosity, cSt40°C 139 110 108 147100°C 13.1 12.2 14.3 14.8
Sulphated Ash, % 0.01 0.45 0.45 0.80
TBN-E 1.1 5.2 5.2 7.7
Pour Point, °C -18 -27 -33 -30
Mysella - Premium Natural Gas Engine Oils 3.72.03
Synthetic ester based, biodegradable hydraulic oils.
Recommended Applications:• Hydraulic and power transmission systems where leakage
could mix with the soil or water• Hydraulics on heavy duty construction and earth moving
equipment• Machine tool hydraulics• General industrial control systems• Hydrostatic drive gears• Moderately loaded gears where an anti-wear hydraulic oil is
specified• Where DIN 51524 Part 2 or Part 3 (HLP/HVLP) anti-wear
petroleum oil is specified• Bulk operating temperature should not exceed 90°C
Advantages:• Readily biodegradable• Excellent viscosity/ temperature characteristics, high VI• “Stay-in-grade” shear stability• Excellent corrosion protection• Good oxidation resistance• Wear protection under severe duty situations• Compatible with mineral oils, insoluble in water
Approvals:• Meets requirements of Caterpillar BF-1biodegradable hydraulic
fluids
Properties SHELL NATURELLE HF-E
Grades 32 46
Product Code 407-210 407-211
Viscosity, cSt40°C 31.6 46.1100°C 6.3 9.1
Viscosity Index 156 182
Pour Point, °C -60 -51
Flash Point (COC), °C 236 219
INDUSTRIAL OILS
7.32
Shell Naturelle HF-E - Synthetic Biodegradable Hydraulic Oil
INDUSTRIAL OILS
7.33
Biodegradable anti-wear hydraulic oil based on a mixture ofsynthetic ester and vegetable oil.
Recommended Applications:• Suitable for the majority of hydraulic applications• Including axial piston and vane pumps• Mining, mobile forestry equipment where leakage could mix
with soil or water• Oil in the hydraulic system must be kept free from water,
<1000 ppm• Recommended operating temperature range -25°C to +70°C
Advantages:• High degree of biodegradability• Contains a significant amount of renewable resource• Stable viscosity at -20°C• Reduced tendency to form sticky deposits when accidentally
spilled• Excellent lubricity• Excellent anti-wear protection
Approvals:• Vickers V-104C Pass• Vickers 35VQ25 (M-2952-S) Pass
Properties SHELL NATURELLE HF-M
Grade 46
Product Code 407-214
Viscosity, mm2/s40°C 42.6100°C 9.6
Viscosity Index 220
Pour Point, °C -39
Rust (Distilled Water) Pass
FZG, failure load stage >12
Shell Naturelle HF-M - Biodegradable Hydraulic Oil
Factory Mutual approved as a less hazardous fluid. Shell FR-N Oilis an ISO Class HFDU anhydrous less flammable hydraulic fluid.
Recommended Applications:• Typical applications are in the metal, mining and glass industries.• Hydraulic installations; it provides good lubrication and a
higher degree of fire resistance.
Advantages:• Less flammable - greater fire resistance to that provided by
conventional mineral oils • Cost effective performance - in most plant hydraulic
applications and is very cost competitive when compared topolyol esters
• Fully compatible with mineral hydraulic oils. No majormodification of the hydraulic circuit is necessary
• Wear protection and lubricity - meets the anti-wear requirementsof virtually all vane pumps (where this property is mostimportant).
• When maintained properly, the fluid can provide equivalent orbetter vane pump performance than many mineral-basedhydraulics.
• Provides satisfactory service in most piston and gear pumps.Passes FZG load stage 12, demonstrating excellent loadcarrying ability.
• Long oil life - in most applications due to its oxidationinhibition. For optimum life, system-operating temperaturesshould not exceed 60-65 °C for extended periods.
• Fluid maintenance - to maximize fluid life, watercontamination should be avoided.
• High degree of biodegradability - Contains a significantamount of a renewable resource
• High Viscosity Index - Minimal change of viscosity over widerange of operating temperatures
• Seal Compatibility - compatible with all seal materials and paintsnormally specified for use with petroleum mineral oils exceptthose made from natural rubber. Recommended elastomersinclude NBR, Fluorocarbon, Fluorosilicone, and Polyacrylate.
Approvals:• Eaton Vickers 104C & 35VQ25 performance • Denison T6C vane pump performance
Shell FR-N - High Performance, Less Flammable Hydraulic Fluid 3.89.02
INDUSTRIAL OILS
7.34
Properties SHELL FR-N OIL
Grades 46 48
Product Code 407-676 407-674
Appearance Clear light amber Clear light amber
Viscosity, cSt (mm2/s)mm2/s at 40°C 47 69mm2/s at 100°C 9.2 13.9
Viscosity Index 202 >200
Pour Point, °C -21 -18
Flash Point, COC, °C 234 260
Shell FR-N - High Performance, Less Flammable Hydraulic Fluid 3.89.02
INDUSTRIAL OILS
7.35
INDUSTRIAL OILS
7.36
A premium, general purpose water glycol fire resistant hydraulicfluid.
Recommended Applications:• Where hydraulic piping may rupture and spray hydraulic fluid
onto hot surfaces, where mineral based fluids can ignite andcause a severe hazard
• Precision industrial and mobile hydraulic systems up to 2,000psi @ 50°C. Higher pressures (3,000 psi) and temperaturesmay be possible
• Underground mining applications• Where Group 1 Factory Mutual or CANMET fluids are required
Advantages:• Excellent fire resistance• Good anti-wear characteristics, protection against pump and
component wear• Inherently low pour point and excellent viscosity/
temperature characteristics• Liquid and vapour phase corrosion inhibited to protect
ferrous and non-ferrous components• Readily biodegradable, low ecotoxicity, reduced environmental
liability• Non-WHMIS controlled, low toxicity
Approvals:• Factory Mutual Group 1 approved• CANMET - CAN3-M423-M84 approved for use in underground
mines
For information on hydraulic design considerations andmaintenance of Water Glycol fluids, contact Shell Canada’s HelpCentre.
Properties NO FIRE WG 200R
Grades 46
Product Code 407-670
Appearance Clear Red
Viscosity, cSt40°C 44
Water Content, % m 39
PH 9.5
Pour Point, max. °C -50
“No Fire” WG 200R - Water GlycolFire Resistant Hydraulic Fluid 3.90.00
INDUSTRIAL OILS
7.37
INDUSTRIAL OILS
A mineral oil based full industrial extreme pressure enclosedgear oil. Omala Oils are designed to protect gearing against highloads / shock loading, and for use in oil mist systems.
Recommended Applications:• Enclosed industrial gears including worm gears• Rolling bearings in pump crankcases• Oil mist (oil fog) applications
Advantages:• Full industrial EP• Excellent load carrying properties protect against shock
loading and prevent scuffing and galling (adhesion)• Outstanding foam performance• Outstanding water separation• FZG, 12th stage load pass• Rust and oxidation inhibited• Excellent sludge and oxidation control• Withstand continuous operating temperatures up to 93°C• Non corrosive to yellow metals up to moderate temperatures• Little or no free fog release in condensing mist units• Lead and Chlorine free
Approvals:• Meets or Exceeds US Steel 224 for lead free EP gear oil• Meets or Exceeds AGMA 250.04• Meets Hydro Quebec PAEM 89204• Meets or Exceeds DIN 51517 Part 3• Meets or Exceeds requirements for David Brown gear boxes• Approved by Cincinnati Milacron (selected grades)• Omala 1000 meets Marion GL-250• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
7.38
Omala - Premium EP Gear Oils 3.10.15
INDUSTRIAL OILS
7.39
Prop
ertie
sO
MA
LA
Gra
des
6810
015
022
032
046
068
010
00
AG
MA
No.
EP2
EP3
EP4
EP5
EP6
EP7
EP8
EP8A
Prod
uct C
ode
407-
528
407-
527
407-
529
407-
531
407-
533
407-
534
407-
532
407-
535
Visc
osity
, cSt
40°C
67.5
100.
014
9.7
233
322.
646
5.1
690.
999
710
0°C
8.58
11.3
14.8
19.6
24.3
30.8
36.3
46
Visc
osity
Inde
x97
9898
9696
9686
87
Pour
Poi
nt, °
C-3
0-2
4-2
4-1
8-1
2-1
2-9
0
Flas
h Po
int,
°C24
225
025
625
825
026
023
823
8
Tim
ken
OK
Load
Typi
cal (
Kg.)
27.5
27.5
27.5
31.8
27.5
27.5
29.5
31.8
Omala - Premium EP Gear Oils 3.10.15
Premium, Extreme Pressure, synthetic industrial gear and bearingoils.
Recommended Applications:• Enclosed industrial gears including worm gears that require an
EP gear oil• “Lubricated-for-life” systems• Gear boxes operating at elevated temperatures• Rolling bearings in pump crankcases
Advantages:• Fully synthetic (PAO, Synthetic hydrocarbon) base stocks• Compatible with seals and paints used with mineral oils• Full industrial EP additive system• Performance superior to conventional mineral based industrial
gear oils• Reduced oil change frequency• Increased equipment reliability, life and operational efficiency• Improved load carrying properties protect against shock
loading and prevent scuffing and galling (adhesion)• Low traction coefficients, reduced energy consumption• Improved system cleanliness, oxidation resistance• Improved low temperature characteristics• Outstanding foam performance• Outstanding water separation• FZG, 12th stage load pass• Rust inhibited, non-corrosive to yellow metals up to moderate
temperatures
Approvals:• Meets the requirements of major gear box manufacturers• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
Properties OMALA OILS HD
Grades 100 220 460 680
Product Code 407-546 407-541 407-542 407-543
Viscosity, cSt40°C 100 222.4 458.3 668100°C 15.0 25.8 45.5 62.6
Viscosity Index 157 148 155 164
Pour Point, °C -48 -48 -42 -39
Flash Point, °C 252 245 240 236
4Ball EP (Weld), kg 290 290 290 290
INDUSTRIAL OILS
7.40
Omala Oils HD - Synthetic Industrial Gear Oils 3.19.01
Premium, non-EP, synthetic industrial gear and bearing oils.
Recommended Applications:• Lightly loaded, enclosed industrial gears subjected to severe
operating conditions and NOT requiring an EP gear oil• “Sealed-for-life” systems• Gear boxes operating at elevated temperatures• Moderately loaded rolling bearings in pump crankcases• Oil circulation systems• Marine separators• For synthetic “EP” gear oils see Shell Omala Oils HD
Advantages:• Fully synthetic (PAO, Synthetic hydrocarbon) base stocks• Compatible with seals and paints used with mineral oils• Performance superior to conventional mineral based industrial
gear oils• Longer oil life, longer component life• Increased equipment reliability, life and operational efficiency• Low traction coefficients: reduced energy consumption• Improved system cleanliness: oxidation and thermal resistance• Improved low temperature characteristics• Outstanding foam performance• Outstanding water separation• FZG, 12th stage load pass• Rust inhibited, non-corrosive to yellow metals up to moderate
temperatures• Worm gear reducers (460 grade)
Approvals:• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
Properties OMALA OILS RL
Grades 150 220 460
Product Code 407-548 407-544 407-545
Viscosity, cSt40°C 153 222 458100°C 19.8 25.9 45.5
Viscosity Index 149 149 155
Pour Point, °C -54 -48 -42
Flash Point, °C 236 240 274
4Ball EP (Weld), kg 210 210 210
INDUSTRIAL OILS
7.41
Omala Oils RL - Synthetic Industrial Gear Oils 3.04.01
A low viscosity straight mineral oil.
Recommended Applications:• Diluent for heavy duty metalworking oils• Coolant / lubricant for diamond tipped saws, for cutting
stones and ceramics, and for machining non-ferrous metalsand alloys
• Cutting fluid in lapidary applications, eye glass lens grinding• Calibration fluid for diesel injectors• Water-proofing paper
Advantages:• Very low viscosity• Nearly odourless• Nearly transparent in colour
Approvals:• Meets FDA as an Aluminum Rolling Lubricant
Properties PELLA A
Product Code 407-790
Viscosity, cSt40°C 4.43
Pour Point, max °C 0
Flash Point (COC), °C 136
Flash Point (TAG), °C >98
Fire Point, °C 150
Aniline Point, °C 87
Distillation Range, °C 274 - 326
INDUSTRIAL OILS
7.42
Pella A - Low Viscosity Mineral Oil 3.30.06
Lubricant to reduce friction between the guide surfaces and thesaw face.
Recommended Applications:• Sawguide applications in sawmills• Linear or rotating guideways• Low or high surface speeds, light or heavily loaded• Chains
Advantages:• Allows for higher accuracy and better surface finish of lumber• Tacky nature provides non-drip property• Anti-wear provides protection against scoring and wear of
equipment subject to heavy loads• Separates readily from water• Corrosion protection
Properties SAWGUIDE
Grade 220
Product Code 407-504
Appearance Tacky
Viscosity, cSt40°C 217.1
Viscosity Index 99
Pour Point, °C -18
Flash Point, °C 248
TAN 0.41
INDUSTRIAL OILS
7.43
Sawguide Oil - Saw Mill Sawguide Lubricant
Tacky, general purpose “non-spattering” lubricating oils thatreduce drippage and staining.
Recommended Applications:• General purpose, light duty rapidly moving parts• Once-through applications• Textile industry in leaky comb boxes, looms, saddle and top
rolls, loosely fitting sleeve bearings• Saw mill chains, light duty gears and cams, sleeve bearings• Metal working, printing, container manufacture, wood
working machines etc.
Advantages:• Heavy, tacky nature reduces dripping and improves metal
adhesion over straight mineral oils• Reduced consumption and throw-off• Non staining
Properties STRINGOL
Grades B D
Product Code 407-811 407-813
Appearance Tacky Tacky
Viscosity, cSt40°C 99.1 262100°C 12.3 21.6
Viscosity Index 95 95
Pour Point, °C -21 -12
Flash Point, °C 214 220
TAN-C 0.1 0.1
INDUSTRIAL OILS
7.44
Stringol - Non Drip Oil 3.07.07
A low viscosity, mineral oil based rust and oxidation oil.
Recommended Applications:• High speed spindle bearing applications which do not require
an anti-wear oil as found on textile machines and othermachine tools
• Hydraulic systems that do not require anti-wear type oils• Airline lubricators in pneumatic systems• Any light duty, general lubrication application requiring a very
light mineral oil
Advantages:• Utilizes special base stocks• Rust and oxidation inhibited• Superb water separation characteristics• Very low foaming tendency
Properties TELLUS 10
Grade 10
Product Code 407-160
Viscosity, cSt40°C 9.7100°C 2.4
Viscosity Index 34
Pour Point, °C -57
Flash Point, °C 152
INDUSTRIAL OILS
7.45
Tellus 10 - Spindle Oil 3.01.14
A premium mineral oil based, anti-wear hydraulic oil. New andimproved.
Recommended Applications:• All hydraulic systems requiring an anti-wear oil• Oil circulating systems including those recommending R&O
oils, where it is desirable to rationalize that number of oilsbeing used
• Plain and rolling element bearings in pump crankcases, someelectric motor bearings etc.
• Gear sets requiring non-EP gear oils• Steam turbines should use Shell Turbo T Oils• Low temperature applications should use Shell Tellus T Oils• Tellus Oils should not be used in pumps containing silver
plated components
Advantages:• Excellent wear protection, for use in all pump types at all
pressure levels• Advanced oxidation stability• Improved wet filterability as demonstrated in Denison T6C
vane pump test• Hydrolytic stability protects against degradation in the
presence of water• Improved tolerance to contamination• Improved frictional characteristics• Excellent water separation• Excellent air release properties• Silicone-free
Approvals:• Denison HF-O, HF-2• Passes Denison T6C vane pump test• Meets Vickers* M-2952-S• Passes Vickers* 35VQ25 vane pump test• Passes Vickers* 104C vane pump test• Cincinnati Machine P-68, P-69, P-70• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n2 (hydraulic oil); avoid foodcontamination during application and storage.
* Eaton Vickers
INDUSTRIAL OILS
7.46
Tellus - Premium Hydraulic and Circulating Oils 3.01.14
INDUSTRIAL OILS
7.47
Prop
ertie
sTE
LLU
S O
ILS
Gra
des
2232
4668
100
150
Prod
uct C
ode
407-
161
407-
162
407-
163
407-
164
407-
165
407-
166
Visc
osity
, cSt
40°C
21.6
32.2
46.3
68.2
96.7
147
100°
C4.
235.
526.
948.
8811
.014
.6
Visc
osity
Inde
x99
108
106
103
100
97
Pour
Poi
nt, °
C-3
6-3
3-3
0-2
7-2
7-2
4
Flas
h Po
int,
°C20
821
222
023
625
428
6
Tellus - Premium Hydraulic and Circulating Oils 3.01.14
Premium, synthetic, anti-wear hydraulic oils.
Recommended Applications:• All hydraulic systems requiring an anti-wear oil that operate at
extremely low or high temperatures, beyond the capabilitiesof mineral based oils
• Including excavators, cranes, shovels, drills, crawlers,“cherrypickers”
• Portable compressors• Plain and rolling element bearings, gears not requiring an EP
oil and circulation systems exposed to extreme temperatures• Tellus HD Oils should not be used in pumps containing silver
plated components• For mineral based low temperature hydraulic oils see Shell
Tellus T Oils
Advantages:• Uses PAO (Synthetic hydrocarbon) base oils• Compatible with seal materials and other mineral oils• High natural Viscosity Index, low natural pour points• Long Life - resists oxidation at high temperatures• Excellent wear protection, for use in all pump types at all
pressure levels• Thermally stable at extreme loads and temperatures• Hydrolytic stability protects against degradation in the
presence of water• Rapid air release without foaming• Long term rust and corrosion protection• Excellent water separation
Approvals:• Denison HF-O• Meets Vickers M-2950-S and I-286-S• Passes Vickers 35VQ25 and 104C vane pump tests• 22 Grade - Approved for Bucyrus Erie 49RZ & 59R Blast Hole
Drills
INDUSTRIAL OILS
7.48
Tellus HD - Synthetic Hydraulic Oils 3.15.01
Properties TELLUS HD OILS
Grades 22 46
Product Code 407-131 407-133
Viscosity, cSt- 40°C 2754 11,685+ 40°C 21.44 45.36100°C 5.04 8.48
Brookfield Viscosity, cP- 40°C 2,520 10,879
Viscosity Index 174 167
Pour Point, °C -68 -62
Flash Point, °C 172 220
Fire Point, °C 192 256
INDUSTRIAL OILS
7.49
Tellus HD - Synthetic Hydraulic Oils 3.15.01
INDUSTRIAL OILS
7.50
Tellus T Oils are all-season (low temperature, multigrade)versions of Shell Tellus Oils. New and improved.
Recommended Applications:• Year-round use in all mobile and stationary hydraulic systems
requiring an anti-wear oil that operate outdoors or have flowlines that are exposed to low temperatures
• Including excavators, cranes, shovels, drills, crawlers,“cherrypickers”
• Saw mills, woodlands operations and snow removalequipment
• Portable compressors• Circulating systems including those servicing plain and rolling
element bearings in pump crankcases and some electricmotor bearings etc. and gear sets requiring non-EP gear oilswhere temperatures vary seasonally
• Tellus T Oils should not be used in pumps containing silverplated components
Advantages:• Improved low temperature fluidity to reduce non-productive
warm-up time, minimize energy losses and reduce pumpcavitation
• All-season protection• Excellent resistance to viscosity breakdown (shear)• Premium anti-wear protection, for use in all pump types at all
pressures• Advanced oxidation and thermal stability against high heat• Improved wet filterability as demonstrated in Denison T6C
vane pump test• Improved tolerance to contamination• Improved frictional characteristics• Excellent air release properties• Silicone-free
Approvals:• Denison HF-O, HF-2• Passes Denison T6C vane pump test• Meets Vickers* M-2950-S• Pass Vickers* 35VQ25 vane pump test• Pass Vickers* 1-286-S• Cincinnati Machine P-68, P-69, P-70• Approved for the requirements of CFIA (Canadian Food
Inspection Agency),Type n2 (hydraulic oil); avoid foodcontamination during application and storage.
*Eaton Vickers
Tellus T Oils - Premium All-Season Hydraulic Oils 3.13.12
INDUSTRIAL OILS
7.51
Prop
ertie
sTE
LLU
S T
OIL
S
Gra
des
T15
T22
T32
T46
T68
Prod
uct C
ode
407-
154
407-
157
407-
159
407-
179
407-
169
Visc
osity
, cSt
40°C
15.2
22.7
32.0
45.9
67.7
100°
C4.
15.
16.
47.
9510
.1
Visc
osity
Inde
x19
016
315
614
513
3
Broo
kfie
ld, c
P-2
0°C
274
680
1,48
33,
081
7,40
0-3
0°C
856
2,56
76,
735
14,0
9140
,613
-40°
C2,
908
11,4
8032
,086
93,4
65-
--4
5°C
5,85
625
,236
80,1
01-
--
-
Pour
Poi
nt, °
C-5
7-5
1-4
5-4
2-3
6
Flas
h Po
int,
°C11
416
621
222
625
2
Max
. Typ
ical
O
ilO
pera
ting
Rang
e, °
C-4
7 to
44
-39
to 5
6-3
2 to
67
-27
to 7
8-2
1 to
87
Tellus T Oils - Premium All-Season Hydraulic Oils 3.13.12
A mineral based, heat transfer oil.
Recommended Applications:• For use in indirect fired heat transfer systems• Particle board mills, sawmills, asphalt plants• In closed systems, up to 290°C for continuous operation,
315°C for intermittent periods
Advantages:• Oxidation inhibitor package protects the base oil from
deterioration• Excellent resistance to thermal cracking• Low vapour pressure• Rust inhibited to prevent corrosion• Low temperature start-ups to - 5°C for centrifugal oil pumps
and - 7°C for gear pumps
Properties THERMIA C
ISO Grades 68
Product Code 407-640
Viscosity, cSt40°C 64100°C 8.2
Viscosity Index 96
Pour Point, °C -6
Flash Point (COC), °C 260
Flash Point (PMCC), °C 210
TAN-C 0.005
INDUSTRIAL OILS
7.52
Thermia C - Heat Transfer Oil 3.21.11
A non-EP, polyglycol (PAG) synthetic industrial gear oil.
Recommended Applications:• Worm gears• High temperature gear applications - beyond the 93°C limit of
conventional mineral EP gear oils and the 120°C limit ofsynthetic EP gear oils
• Suitable for all types of gears including spur, bevel andplanetary units
• Gear applications where natural load carrying and efficientpower transmission are required
• Seal-for-life gear boxes not requiring an EP gear oil• NOT compatible with mineral based products• NOT compatible with many paints• Neutral effect on most sealing materials• Shell Tivela Oils are not recommended for the lubrication of
gears manufactured from bronze alloys containing aluminum• Where industrial EP oils are required see Shell Omala,
Omala HD or Shell Geartherm
Advantages:• Polyglycol base oil has very high viscosity index, low pour
point, high natural load carrying capacity and low frictionalcharacteristics
• Oxidation stability provides long life for seal-for-life gear boxes• Very good high and low temperature properties• Optimal power transmission• Especially suited for steel and bronze gear tooth interaction as
found in worm gears
Approvals:• Recommended by David Brown, SEW and NORD Gear
Properties TIVELA
Product WB SD
ISO Grades 220 460
Product Code 407-521 407-522
Viscosity, cSt40°C 254.5 467100°C 39.2 76
Viscosity Index 208 200
Typical Operating Range, °C -30 to +170 -20 to +170
FZG 12th Load Stage Pass Pass
INDUSTRIAL OILS
7.53
Tivela - Synthetic Industrial Gear Oils 3.31.02
Lubricant designed to reduce static friction of guide surfaces oftable ways.
Recommended Applications:• Machine tool ways, slides and guides• Horizontal and vertical ways, flat or “V” shaped• Linear or rotating guideways• Low or high surface speeds, light or heavily loaded• Including grinders, milling machines, planers, saw guides,
workheads, work tables, lathe saddles, overhead machinery,conveyors
• Chains• Central oil systems that supply both the slide ways and
hydraulic system should use Tonna V 68.• Bearings and ways of punch presses should use Tonna V 220
to protect equipment from the inherent shock loading• NOT to be used where the oil may contact textile materials
Advantages:• No jerky start-up motion. Low “Stick-Slip” values. Ratio of
static friction to kinetic friction is less than 0.8• Allows for higher accuracy and better surface finish of the
work piece• Tacky nature provides non-drip property for vertical and
overhead ways• Anti-wear provides protection against scoring and wear of
equipment subject to heavy loads• Separates readily from water• Corrosion protection
Approvals:• Cincinnati Milacron P-47, P-50 and P-53
Properties TONNA V
Grades 32 68 220
Product Code 407-506 407-507 407-508
Appearance Tacky Tacky Tacky
Viscosity, cSt40°C 32 68.2 217.1
Viscosity Index 110 104 99
Pour Point, °C -36 -30 -18
Flash Point, °C 206 234 248
TAN 0.49 0.49 0.41
INDUSTRIAL OILS
7.54
Tonna V - Slide Way Lubricant 3.55.04
INDUSTRIAL OILS
7.55
Premium, high performance lubricant for air operatedpercussion tools.
Recommended Applications:• Rockdrills, jackhammers• In mining, road building, construction etc.• Independent rotation or rifle bar drills
Advantages:• Superior wear protection• Controlled atomization and misting• Resistance to dieseling or spontaneous ignition and the
associated heat• Prevents formation of hard carbonaceous deposits• Exceptional low temperature fluidity for wear protection and
atomization at low temperatures• Emulsifies with water to carry water through the drill• Rust inhibited
INDUSTRIAL OILS
7.56
Torcula - Pneumatic Rockdrill Oils 3.53.05
INDUSTRIAL OILS
7.57
Torcula - Pneumatic Rockdrill Oils 3.53.05
Prop
ertie
sTO
RCU
LA
Gra
des
4668
100
150
220
Prod
uct C
ode
407-
855
407-
852
407-
853
407-
854
407-
850
App
eara
nce
Tack
yTa
cky
Tack
yTa
cky
Tack
y
Visc
osity
, cSt
40°C
4668
101
150
227
100°
C8.
89.
311
.715
.320
Visc
osity
Inde
x17
111
310
510
310
1
Pour
Poi
nt, °
C-4
5-2
7-2
4-1
8-1
5
Flas
h Po
int,
°C18
024
225
427
228
2
Fire
Poi
nt, °
C20
829
230
831
832
8
Am
bien
t Tem
pera
ture
Ope
ratin
g Ra
nge,
°C
-30
to +
15
-10
to +
20
-5 to
+ 3
0A
bove
+ 1
0A
bove
+ 1
5
INDUSTRIAL OILS
7.58
Shell Turbo T Oils - Premium Turbine Oils 3.03.08
Shell Turbo T Oils are mineral oil based, rust and oxidation(R&O) inhibited oils.
Recommended Applications:• Steam, water and hydraulic turbines in industrial and marine
use• Stationary, frame type gas turbines requiring a mineral oil
lubricant• Circulating systems requiring R&O oils• Hydraulic systems requiring an R&O type oil (low pressure)• AGMA rust and oxidation inhibited gear lubricants (non-EP)• Plain and rolling element bearings in pump crankcases• For heavier viscosity grades see Shell Morlina Oils
Advantages:• Outstanding oxidation resistance• Specially processed and handled to enhance water separation
and air release• Excellent rust protection
Approvals:• Meets Hydro Quebec PAEM 89201• Meets Ontario Hydro M-332M-B5• Meets General Electric GEK-32568C• Meets Westinghouse 551125 AC• Shell Turbo T32 meets ASEA Brown Boveri (ABB) spec
VTI3200-3/1994/03• Meet Cincinnati Milacron “Rust and Oxidation Inhibited
Hydraulic Oils”CM spec P-38 Shell Turbo T 32CM spec P-54 Shell Turbo T 68CM spec P-55 Shell Turbo T 46
• Approved by the CFIA (Canadian Food Inspection Agency) forindustrial food plant use
• Approved for the requirements of CFIA (Canadian FoodInspection Agency),Type n1, for general use; avoid foodcontamination during application and storage.
INDUSTRIAL OILS
7.59
Shell Turbo T Oils - Premium Turbine Oils 3.03.08
Prop
ertie
sSH
ELL
TURB
O T
OIL
S
Gra
des
3246
6878
100
Prod
uct C
ode
407-
952
407-
953
407-
954
407-
955
407-
956
Visc
osity
, cSt
40°C
3246
6778
.699
100°
C5.
46.
88.
69.
6811
.4
Visc
osity
Inde
x10
210
110
010
110
0
Pour
Poi
nt, °
C-3
0-2
7-2
7-2
4-2
4
Turb
ine
Oil
Stab
ility
Tes
t, hr
.+9
,000
+6,5
00+6
,500
+6,5
00+6
,500
Mineral based, high viscosity, compounded steam cylinder oils.
Recommended Applications:• Steam cylinders• Gears (especially worm gears) and bearings at low
speeds and moderate loads, with either bath or pressure circulation systems
• Some multi-stage reciprocating compressor cylinders and packings
• NOT suitable for hypoid gears• NOT suitable for application below freezing where
additive stability may be affected
Advantages:• Excellent stability• Excellent lubricity associated with classic fatty
compounded oils
Properties VALVATA
Grades J 460 K 680
Product Code 407-320 407-323
Viscosity, cSt40°C 444 640100°C 30.0 37.3
Viscosity Index 96 94
Pour Point, °C -9 -6
Flash Point, °C min 334 340
TAN-C 0.17 0.29
Saponification Number 10.3 18.5
INDUSTRIAL OILS
7.60
Valvata - Compounded Oils 3.35.09
A highly refined paraffinic mineral lubricating oil.
Recommended Applications:• Oil lubricators and central lubrication systems• Lubricating plain and rolling bearings• Spur, helical and bevel gears where an oil which does not
contain additives is adequate• Where gear tooth and bearing loads are not extreme• Moderate temperature applications
Advantages:• Natural high viscosity index and low pour points• Readily separates from water• Low cost• Good oxidation stability
Properties VITREA
Grade 22
Product Code 407-421
Viscosity, cSt40°C 20.3100°C 4.02
Viscosity Index 95
Pour Point, °C -18
Flash Point (COC), °C 196
TAN-C 0.01
INDUSTRIAL OILS
7.61
Vitrea 22 - General Purpose Mineral Oil 3.18.08
INDUSTRIAL OILS
7.62
Mineral based circulating oil specially formulated to provideVapour Space (rust) Inhibition.
Recommended Applications:• For protecting internal, enclosed equipment components from
rusting both above and below the oil level during equipmentidle periods or intermittent use or during shipment
• Also a general purpose rust and oxidation circulating oil• All enclosed oil lubrication systems where rusting may occur
due to steam condensate or atmospheric moisture such as oilstorage tanks, reservoirs, rolling bearing and gear housings,pump crankcases, machine tool housings
• Run-in of new equipment and subsequent shipping. VSI 68may be easily drained and replaced with the operatinglubricant if a different oil is required
• Steam turbine systems where corrosion on tank walls andoverheads is occurring
• Recommended for oil temperatures below 65°C and definitelybelow 95°C for the VSI inhibitor to be effective
• Metal surfaces to be protected should be within 6 feet of thesurface of the oil
• NOT recommended for open systems or surface exposed tothe weather
• See our Lubricants Report for application details
Advantages:• Contains a volatile corrosion inhibitor which adsorbs to metal
surfaces in the enclosed space above the level of the oil in thesystem
• Excellent oxidation stability• Superior demulsibility from water• Resistant to foaming
Properties VSI OIL 68
Grade 68
Product Code 407-880
Viscosity, cSt40°C 68.3100°C 8.6
Viscosity Index 107
Pour Point, °C -27
TAN-C 0.5
VSI Oil - Circulating and Rust Inhibiting Oil 3.43.04
7.63
Page
Engine OilsAlexia 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2Argina S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3Argina T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3Caprinus XR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4Caprinus HPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4Gadinia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6Melina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7Sirius FB Oil 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.8
Greases and Rail LubricantsOssagol C Moly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.27Cardura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.15Alvania EP D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.10
TurbineShell Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.58
Marine SeparatorsOmala RL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.41
MARINE AND RAIL LUBRICANTS
8.1
Table of Contents MA
RIN
E & R
AIL
Premium cylinder oil for low speed crosshead diesel engines.
Recommended Applications:• For use in the separate cylinder lubrication system of low-
speed, crosshead type, marine diesel engines burning heavyfuel oil with high sulphur content (up to 3.5% wt.)
• Slow speed marine diesel engine crankcases
Advantages:• Unique additive technology and HVI base stocks• Suited for new highly rated, fuel efficient, slow-speed marine
diesel engines operating at higher pressures and temperatures• Designed for use with high sulphur (1.0 to 3.5%) fuels• Minimum deposit formation• Lower cylinder and piston wear• Excellent engine cleanliness• Compatible with sight-glass fluids and normal oil seal
materials• Excellent storage stability in conditions on-board ship
Properties ALEXIA
SAE Grade 50
Product Code 407-415
Viscosity, cSt40°C 188100°C 19.0
Viscosity Index 95
Pour Point, °C -9
Flash Point (COC), °C 262
TBN-E 70
Sulphated Ash, %wt 8.11
MARINE AND RAIL LUBRICANTS
8.2
Alexia Oil 50 - Diesel Engine Cylinder Oil
MARINE AND RAIL LUBRICANTS
8.3
Premium cylinder and crankcase oils for medium speed marinediesel engines: Argina S (TBN = 20) and Argina T (TBN = 30).
Recommended Applications:• Cylinders and crankcase oil for medium speed industrial and
marine diesel engines burning residual fuel oils with sulphurcontent up to 2.5%
• Marine engine reduction gears
Advantages:• Unique additive technology and HVI base stocks• Suited for modern medium speed diesel engines• Excellent detergency to protect against deposits caused by
heavy fuels and carbonaceous deposits thus reducing ring andliner wear, blow-by and oil consumption. Excellent enginecleanliness
• Excellent TBN retention• Superior thermal stability and resistance to oxidation• Rapidly neutralizes acids for long-term corrosion protection• Formulated without ashless dispersant additives for use with
lubeoil separators• Resists sludge formation in the crankcase and under valve
covers
Approvals:• Approved by many marine engine manufacturers• API CD• Cat Series 3
Properties ARGINA
Grades S 40 T 30 T 40
Product Code 407-437 407-434 407-435
Viscosity, cSt40°C 135 106 143100°C 14.1 12.0 14.6
Viscosity Index 102 101 99
Pour Point, °C -24 -24 -24
Flash Point (COC), °C 274 237 240
TBN-E 20 30 30
Sulphated Ash, %wt 2.5 3.8 3.8
FZG Load Stage Pass 11 11 11
Argina - Marine Diesel Engine Oils
Premium locomotive crankcase diesel engine oils.
Recommended Applications:• Railway, marine and stationary power plant engines• EMD,Alco and GE engines
Advantages:• Two TBN levels:
• Caprinus XR 13 TBN• Caprinus HPE 17 TBN
• Superior TBN retention with unique Shell detergenttechnology
• Excellent viscosity control / retention• Multigrade products offer potential fuel savings• Multigrade products offer potential reduced oil consumption• Unique Shell viscosity index improver used in multigrade
products• Totally zinc-free formulations for use in all EMD engines• Compatible with other common railroad diesel engine oils • Caprinus XR 40 is chlorine free • Caprinus XR grades are also chlorine free
Approvals:• Accepted by major railroads throughout the world• XR and HPE meet GE’s LMOA Generation 5 extended drain
requirement for high horsepower GE engines• HPE meets Caterpillar Micro Oxidation Test• EMD oxidation / corrosion• GE oxidation• Union Pacific oxidation test• CAT 1G-2 bench engine test• API CD
MARINE AND RAIL LUBRICANTS
8.4
Caprinus - Railroad and Marine Engine Oils 1.35.04
Prop
ertie
sCA
PRIN
US
Gra
des
HPE
HPE
XRXR
4020
W-4
040
20W
-40
Prod
uct C
ode
435-
049
435-
050
435-
055
435-
056
Visc
osity
, cSt
40°C
146
126
144
123
100°
C14
.614
.614
.614
.5
Visc
osity
Inde
x10
112
010
011
9
Pour
Poi
nt, °
C-2
5-3
6-2
7-3
0
Flas
h Po
int,
°C26
425
427
324
7
TBN
- E17
1713
13
Sulp
hate
d A
sh, %
wt
1.82
1.81
1.45
1.46
MARINE AND RAIL LUBRICANTS
8.5
Caprinus - Locomotive Engine Oils 1.35.04
Premium medium-speed trunk piston engine oils for enginesoperating on distillate fuels.
Recommended Applications:• Highly-rated, medium speed, trunk-piston marine engines
operating on distillate fuels• Auxiliary marine engines• Geared transmissions• Turbochargers• Variable pitch propellers• Oil lubricated stern tubes• Deck machinery• Other applications requiring a 30 or 40 wt oil
Advantages:• Designed to effectively neutralize corrosive acids which can
form from the use of higher sulphur content marine fuels• Protect against rust and corrosion caused by sea water
contamination• Ensures a clean engine, free from sludge and deposits• Compatible with all normal oil seal materials• Designed to be used in centrifugal purification systems
Approvals:• Approved by most leading trunk piston diesel engine
manufacturers• MIL-L-2104C / API CD• MTU
Properties GADINIA
Grades 30 40
Product Code 407-418 407-419
Viscosity, cSt40°C 107.4 146.8100°C 11.8 14.6
Viscosity Index 98 98
Pour Point, °C -24 -21
Flash Point (COC), °C 236 241TBN-E 12.0 12.0
Sulphated Ash, %wt 1.35 1.35
FZG Load Stage Pass 12 12
Zn, ppm 420 420
Ca, ppm 3,800 3,800
P, ppm 360 360
MARINE AND RAIL LUBRICANTS
8.6
Gadinia - Marine Diesel Engine Oils
Premium multi-purpose crankcase oil for low speed, trunk-pistonand crosshead marine diesel engines.
Recommended Applications:• Crankcase systems of low speed, crosshead,
marine diesel engines• Main and auxiliary trunk-piston diesel engines
burning distillate fuels• Geared transmissions• Turbochargers• Variable pitch propellers• Oil lubricated stern tubes• Deck machinery• Other applications requiring a 30 wt oil
Advantages:• Oxidation stability reduces oil thickening and
deposits in piston cooling spaces• Excellent dispersancy to prevent sludging and allows for
contaminant removal by filters or centrifugal separation• Neutralizes strong and corrosive acids from
cylinder oils entering the crankcase• Good water shedding properties• Resistant to corrosion by salt water
Approvals:• MIL-L-2104C / API CD• Sulzer - crosshead marine diesel engines• MAN B&W - crosshead marine diesel engines
Properties MELINA
Grades 30
Product Code 407-409
Viscosity, cSt40°C 108.8100°C 12.0
Viscosity Index 95
Pour Point, °C -24
Flash Point, °C 274
TBN-E 8.0
Sulphated Ash, %wt 1.0
FZG Load Stage Pass 12
MARINE AND RAIL LUBRICANTS
8.7
Melina - Marine Diesel Engine Oils
Properties SIRIUS FB OIL 30
Product Code 407-460
Density at 15°C, kg/m3 887
Pour Point, °C -24
Viscosity @ 100°C 11.8
Calcium, % mass 0.38
Sulphated Ash, % mass 4.8
TBN-E 13.5
Premium quality marine diesel engine oil formulated for use in medium speed trunk piston engines operating on distillatefuels.
Recommended Applications:Sirius FB Oil 30 is specifically formulated to control oilconsumption in modern distillate fuelled engines where linerlacquering can be a problem.
Advantages:• Reduced levels of liner lacquer• High level of protection against bore polishing• Excellent piston and crankcase cleanliness• Ability to release water and contaminants in
centrifugal separators• Excellent load carrying properties as required
for lubricating reduction gears• Meets API Services Classification CD• Fully approved in Stork,Wartsila Diesel, MWM Deutz,
MAN B&W,Alpha Diesel, and MaK engines
MARINE AND RAIL LUBRICANTS
8.8
Sirius FB Oil 30 Marine Diesel Engine Oil
Page
ParaffinicShellflex 210, 310, 330, 680, 810 . . . . . . . . . . . . . . . . . . 9.4
NaphthenicShellflex 3131, 3211, 3271, 3311, 3371,3681, 4131, 4132, 6371 . . . . . . . . . . . . . . . . . . . . . . . . . 9.2
PROCESS OILS
9.1
Table of Contents
PRO
CES
S O
ILS
Refined, naphthenic petroleum fractions.
Recommended Applications:• Rubber compounding / manufacturing• Elastomers• Adhesives• Carrier oils• Plasticizers• Most process oil applications
Advantages:• Rich in naphthenic cyclic chemical structures• Very consistent physical and chemical properties• Wide range of viscosities available• Do not contain any additives• Low natural pour points• Good stability• Improved solvency over paraffinic process oils
PROCESS OILS
9.2
Shellflex - Naphthenic Process Oils 3.02.02
Prop
ertie
sSH
ELLF
LEX
(NA
PHTH
ENIC
) OIL
S
Gra
des
371
3131
3211
3271
3311
3371
3681
4131
6371
Prod
uct C
ode
410-
371
410-
313
410-
321
410-
327
410-
331
410-
337
410-
681
410-
431
410-
637
Den
sity
@ 1
5°C
, kg/
m3
897
872
886
897
901
904
910
885
903.
9
Visc
osity
, cSt
@ 4
0°C
92.9
9.18
20.2
40.2
54.3
79.5
149.
99.
392
.0
Visc
osity
, cSt
@ 1
00°C
8.28
2.4
3.8
5.5
6.7
8.4
12.2
2.6
8.19
Visc
osity
Inde
x31
5952
6063
7360
4536
Pour
Poi
nt, °
C-2
9-3
6-2
1-1
2-1
5-1
8-1
5-5
1-2
8
Flas
h Po
int,
°C22
415
717
420
021
021
322
915
521
3
Ani
line
Poin
t, °C
9980
8489
9192
9676
97
VG
Con
stan
- -
0.84
150.
8434
0.84
670.
8450
0.83
710.
8348
0.86
5-
-
Refra
ctiv
e In
dex
@ 2
0°C
1.48
981.
4793
1.48
671.
4938
1.49
501.
4981
1.50
241.
4815
1.48
96
Refra
ctiv
e In
terc
ept
- -
1.04
251.
046
1.04
41.
0456
- -
- -
- -
- -
Rel.
Mol
ecul
ar M
ass
- -
325
390
365
420
440
465
261
- -
9.3
PROCESS OILS
Shellflex - Naphthenic Process Oils 3.02.02
Refined, paraffinic (HVI) petroleum fractions.
Recommended Applications:• Dust suppressant• Rubber compounding / extending component• Shellflex 210, 310, 330 and 680 are ASTM 1048 type rubber
extending oils• Shellflex 810 is an ASTM 103 type rubber extending oil• Carrier oil• Elastomer manufacture• Plasticizers• Adhesives• Most process oil applications
Advantages:
• High concentration of saturated chemical structures• Very consistent physical and chemical properties• Wide range of viscosities available• Do not contain any additives• Low natural pour points for paraffinic oils• Good stability• Modest solvency
PROCESS OILS
9.4
Shellflex - Paraffinic Process Oils 3.02.02
PROCESS OILS
9.5
Shellflex - Paraffinic Process Oils 3.02.02Pr
oper
ties
SHEL
LFLE
X (P
ARA
FFIN
IC) O
ILS
Gra
des
210
310
680
810
Prod
uct C
ode
410-
210
410-
310
410-
680
410-
810
Den
sity
@ 1
5°C
, kg/
m3
862.
587
4.1
879.
089
4.7
Visc
osity
, cSt
@ 4
0°C
20.3
51.2
117
526
Visc
osity
, cSt
@ 1
00°C
4.0
7.2
12.3
33
Visc
osity
Inde
x95
9595
95
Pour
Poi
nt, °
C-1
8-1
2-9
-9
Flas
h Po
int,
°C22
024
227
433
4
Ani
line
Poin
t, °C
9810
711
712
6
VG
Con
stant
0.81
420.
8113
0.80
420.
8000
Refra
ctiv
e In
dex
@ 2
0°C
1.47
091.
4760
1.47
901.
4880
Refra
ctiv
e In
terc
ept
1.04
301.
0420
1.04
321.
0442
Car
bon
Type
, %m
Aro
mat
ic0
00
2.6
Nap
hthe
nic
3434
3128
.3Pa
raffi
nic
6666
6969
.1
Rel.
Mol
ecul
ar M
ass
365
435
515
700
Page
BiodegradableNautilus Biodegradable Outboard Motor Oil. . . . . . . . . 10.9Nautilus Biodegradable Bilge Cleaner . . . . . . . . . . . . . . 10.13Nautilus Biodegradable Boat Cleaner . . . . . . . . . . . . . . 10.14
Chain Case OilsAdvance 100% Synthetic Chain Case Oil . . . . . . . . . . . 10.6
Chain OilChain Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7
Engine Oils
4 StrokeNautilus 4 Stroke Engine Oil. . . . . . . . . . . . . . . . . . . 10.10
2 StrokeShell Advance Premium Snowmobile Oil . . . . . . . . . 10.3Advance Snow Ultra - Syn. Snowmobile Oil . . . . . . . 10.4Nautilus Premium Outboard Motor Oil . . . . . . . . . . . 10.8Nautilus PWC Personal Watercraft Oil. . . . . . . . . . . . 10.17XTC-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.18
GearNautilus Marine Gear Oil . . . . . . . . . . . . . . . . . . . . . . . 10.12Nautilus Synthetic Gear Oil . . . . . . . . . . . . . . . . . . . . . 10.16
GreaseAdvance Snow Ultra. . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4
PumpNautilus Jet Pump Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10.15
SPECIALTY LUBRICANTS
10.1
Table of Contents
SPEC
IALTY
LUBES
SPECIALTY LUBRICANTS
10.2
A premium mineral based, 2 stroke snowmobile oil.
Recommended Applications:• High output 2 stroke snowmobile engines• Pre-mix applications and oil injection systems
Advantages:• Ashless formulation minimizes plug fouling and preignition• Reduced exhaust smoke, up to 85%• Low exhaust odour, no ammonia odour• Superior low temperature performance, SAE Category 4 @-40°C• Improved lubricity and scuffing performance• Detergent / dispersant formulation minimizes deposit
formation• Protects engine against rust
Approvals:• Meets all major snowmobile manufacturers recommendations
including Arctic Cat, Bombardier, Polaris,Yamaha• Exceeds TC-W3*• Meets API TC• Meets JASO FC smoke emission standard
Properties SHELL ADVANCE PREMIUMSNOWMOBILE OIL
Product Code 427-511
API Rating TC
SAE Fluidity/Miscibility Rating 4
Colour Blue
Viscosity, cSt40°C 27.3100°C 5.8
Brookfield Viscosity, cP-40°C 11,600
Pour Point, °C -51
Flash Point, °C 79
SPECIALTY LUBRICANTS
10.3
Shell Advance Premium Snowmobile Oil 1.06.13
A high performance, synthetic, 2 stroke snowmobile engine oil.
Recommended Applications:• High performance, high output 2 stroke snowmobile engines• Including those with variable exhaust systems such as RAVE*• Pre-mix and direct oil injection systems
Advantages:• Low ash, synthetic formulation minimizes
plug fouling and preignition• Detergent / dispersant formulation minimizes
piston and ring deposits• Superior low temperature performance• Reduced exhaust smoke, visible exhaust smoke is
essentially eliminated after warm-up• No ammonia odour formulation• Improved lubricity and anti-scuffing protection• Superior rust protection• Proven performance• Designed for unleaded gasoline up to 100:1 mixing ratio
Approvals:• Meets all major snowmobile manufacturers recommendations
including Arctic Cat, Bombardier, Polaris,Yamaha• Exceeds highest API-TC, JASO-FC and ISO-EGD standards for
detergency, lubricity, pre-ignition, exhaust system blockage andreduced visible exhaust smoke emission
SPECIALTY LUBRICANTS
10.4
Advance Snow Ultra - Premium Synthetic Snowmobile Oil 1.14.06
Properties ADVANCE SNOW ULTRA
Product Code 427-512
API Rating TC
SAE Fluidity/Miscibility Rating 4
Colour Golden Amber
Viscosity, cSt40°C 57.1100°C 9.46
Brookfield Viscosity, cP-40°C 37,400
Pour Point, °C -57
Flash Point, min. °C 80
TBN-E 1.3
Ash Content, % m 0.10
SPECIALTY LUBRICANTS
10.5
Advance Snow Ultra - Premium Synthetic Snowmobile Oil 1.14.06
SPECIALTY LUBRICANTS
10.6
A premium 100% synthetic chain case oil for enclosed chaincase systems
Recommended Applications: All season service in enclosed chain drives for snowmobiles,ATVs and other recreational vehicles.
Advantages: • Outstanding low temperature flow • All-Season operation enabling it to provide maximum
protection over a wide range of temperatures.• Additive system to provide outstanding protection and
lubrication of chains and sprockets.
Properties ADVANCE 100% SYNTHETIC CHAIN CASE OIL
Product Code 427-582
Density at 15°C - Kg/m3 902
Pour Point °C -40
Viscosity Kinematic cSt @ 40 °C 122cSt @ 100 °C 16.6
Brookfield cP @ -40 °C 125,000
Viscosity Index 150
Copper Strip Corrosion Test @ 100 °C for 3 hrs.
Foam PassSequence I PassSequence II PassSequence III Pass
Advance 100% Synthetic Chain Case Oil 1.18.02
SPECIALTY LUBRICANTS
10.7
Premium mineral oils for all chains including chains and bars ofpower chain saws.
Recommended Applications:• All chains, including oil baths, hand and automatic lubricated• Bars and chains of high performance professional power
chain saws• Conveyor systems, sawmills, woodlands, mining operations• NOT to be used as an engine oil in the power heads of saws.
For 2 stroke engine oil see Shell XTC-50 Oil
Advantages:• Additive system protects the chain, bar and sprockets from
wear• Tacky nature reduces fling-off from the chain• Red colour helps distinguish this chain oil from engine oils• Rust Inhibited
Properties CHAIN OILS
Grades Light Heavy
Product Code 431-222 431-221
Colour Red Red
Viscosity, cSt40°C 70 91100°C 9 12
Pour Point, °C -33 -15
Flash Point, °C 220 200
Chain Oils - Chain Lubricant 1.25.07
SPECIALTY LUBRICANTS
10.8
A premium mineral oil based,TC-W3*, 2 stroke outboard motoroil.
Recommended Applications:• All water cooled 2 stroke outboard engines for
both pre-mix and direct oil injection systems• For a full synthetic oil for personal watercraft,
use Shell Nautilus PWC
Advantages:• Dispersant formulation• Improved lubricity and anti-scuffing protection• Low aquatic toxicity• Reduces plug fouling and preignition• Minimizes piston deposits• Superior rust protection• Reduced smoke• Compatible with other TC-WII* and TC-W3* lubricants• Dyed blue for easy identification in pre-mix systems
Approvals:• Exceeds the NMMA TC-W3* standards• Recommended for OMC, Mercury Marine,Yamaha, Susuki, Nissan• Meets JASO FC reduced smoke emission standard
Properties NAUTILUS
Product Code 427-531
API Rating TC
NMMA Rating TC-W3
SAE Fluidity/Miscibility Rating 4
Colour Blue
Viscosity, cSt40°C 27.3100°C 5.8
Brookfield Viscosity, cP-40°C 11,600
Pour Point, °C -51
Flash Point, °C (PMCC) 79
TBN-E 9.1
Ash Content 0.003
Nautilus - Premium Outboard Motor Oil 1.09.09
SPECIALTY LUBRICANTS
10.9
A premium, biodegradable TC-W3*, 2 stroke outboard motor oil.
Recommended Applications:• All water cooled 2 stroke outboard engines for both pre-mix
and direct oil injection systems
Advantages:• Synthetic based formulation• Ashless, dispersant formulation• Improved lubricity and anti-scuffing protection• Less aquatic toxicity• Reduces plug fouling and preignition• Minimizes piston deposits• Superior rust protection• Designed for unleaded gasoline• Blends easily and stays mixed• Compatible with other TC-WII* and TC-W3* lubricants
Approvals:• Exceeds the recertification requirements of NMMA TC-W3*• Fully approved by Canada’s Environmental Choice Program • Meets biodegradability requirements of CEC L-33 T-82• Recommended for OMC, Mercury Marine,Yamaha, Susuki,
Nissan
Properties NAUTILUS BIODEGRADABLEOUTBOARD MOTOR OIL
Product Code 427-536
NMMA Rating TC-W3
Colour Blue/Green
Viscosity, cSt100°C 9.1
Brookfield Viscosity, cP-25°C 5,835
Pour Point, °C -40
Flash Point, °C 110
TBN-E 2.9
Nautilus Biodegradable Outboard Motor Oil 1.40.02
4 stroke inboard and outboard motor oils.
Applications:• Water cooled, gasoline and diesel, inboard and outboard
4 stroke engines• Recommended for all makes and models of 4 stroke engines
including Mercury, Honda, OMC and Yamaha• Consult your owners manual for the proper grade and API
service classification
Advantages:• Viscosity retention to stay-in-grade.The 25W-40 is
formulated without Viscosity Index Improver additives to provide maximum viscosity retention
• Corrosion protection for this severe environment• Longer engine life from improved engine and piston
deposit control• Wear protection• Antifoam control• Low oil consumption
Recommendations:• SAE 10W-30 is API CH-4, CG-4, CF-4, CF/SH• SAE 25W-40 is API SJ, CD• SAE 30 is API SJ
SPECIALTY LUBRICANTS
10.10
Nautilus 4 Stroke Engine Oils 1.41.04
Properties NAUTILUS 4 STROKE ENGINE OILS
Grades 10W-30 25W-40 30
Product Code 425-533 425-534 427-571
Viscosity, cSt40°C 76.7 134.0 97.7100°C 11.8 14.5 11.5
Viscosity Index 149 107 106
CCS (cranking), cP-5°C - - 3,000 - --20°C 2,850 - - - -
MRV Apparent Visc, cP-15°C - - 9,860 - --30°C 23,169 - - - -
Pour Point, °C -33 -24 -30
Sulphated Residue, % wt 1.25 0.75 0.75
TBN-E 10.3 7.5 6.0
Flash Point, °C 219 229 229
SPECIALTY LUBRICANTS
10.11
Nautilus 4 Stroke Engine Oils 1.41.04
A mineral based, premier, multi-purpose, all season multigrade,EP gear oil.
Recommended Applications:• Inboard and outboard gear cases where Type C, 80W-90 gear
oils are recommended
Advantages:• Excellent extreme pressure load carrying ability• Ultimate rust protection needed in a marine environment• Thermal and oxidation stability to eliminate deposits that
form around seals• Controls foaming in gear cases• Retains viscosity and a protective oil film from the use of a
shear stable viscosity index improver additive
Approvals:• GL-5• Exceeds Original Equipment Manufacturers (OEM)
requirements• Recommended for all major inboard and outboard gear cases
including Mercury, Honda, OMC and Yamaha
Properties NAUTILUS MARINE GEAR OIL
Grade 90
Product Code 437-535
Viscosity, cSt40°C 134100°C 14.7
Viscosity Index 110
Pour Point, °C -24
Flash Point, °C 218
SPECIALTY LUBRICANTS
10.12
Nautilus Marine Gear Oil 1.42.02
A biodegradable cleaner for recreational boat bilges.
Recommended Applications:• Cleaning bilges of boats. Will remove oil, wax and other
protective coatings• This product is not to be used as a lubricant
Advantages:• Biodegradable - cleaner degrades before having a negative
impact of aquatic life• Not harmful to marine, plant and water organisms• Non flammable• Non explosive• Contains no nitrates, phosphates, sulphates or chlorine.• Cleaner mixed with water disperses oil from the bilge.
See our “Lubricants Report” for mixing details• No special handling procedures or protective clothing
required
Approvals:• Meets biodegradability requirements of the Environmental
Choice Program (ECP)
Properties NAUTILUS BIODEGRADABLE BILGE CLEANER
Product Code 427-551
Specific Gravity 1.006
Cleaner pH 10.2
SPECIALTY LUBRICANTS
10.13
Nautilus Biodegradable Bilge Cleaner 1.43.01
A biodegradable cleaner for recreational boats.
Recommended Applications:• Cleaning boat bottoms and hulls - water lines and salt water
spots• Engine rooms and oily surfaces• Rust and corrosion from refrigeration containers• Mildew, mould and oil from bilges• Swabbing decks and bulkheads• Atomized in air for odour control• This product is not to be used as a lubricant
Advantages:• Biodegradable - cleaner degrades before having a negative
impact of aquatic life• Not harmful to marine, plant and water organisms• Non flammable• Non explosive• Contains no nitrates, phosphates, sulphates, detergents and
chlorines.• Cleaner mixed with either fresh or salt water. See our
“Lubricants Report” for mixing details• No special handling procedures or protective clothing
required
Approvals:• Meets biodegradability requirements of the Environmental
Choice Program (ECP)
Properties NAUTILUS BIODEGRADABLE BOAT CLEANER
Product Code 427-561
Specific Gravity 1.006
Cleaner pH 10.2
SPECIALTY LUBRICANTS
10.14
Nautilus Biodegradable Boat Cleaner 1.44.01
SPECIALTY LUBRICANTS
10.15
Nautilus Jet Pump Oil is a premium, fully synthetic personalwatercraft jet pump lubricant.
Recommended Applications:• Jet pump lubricant for personal watercraft which require oil
top-up or replacement• Severe service including high temperature conditions
Advantages:• Full synthetic• Extreme pressure additives for excellent wear protection• Extended drain intervals
Approvals:• Meets GL-5 requirements
Properties NAUTILUS JET PUMP OIL
Product Code 427-591
Viscosity, cSt40°C 122100°C 16.6
Viscosity Index 147
Brookfield Viscosity , cP @ -40°C 120,000
Pour Point, °C <-45
Nautilus Jet Pump Oil 1.46.01
SPECIALTY LUBRICANTS
10.16
Nautilus Synthetic Gear Oil is a premium, fully synthetic,extreme pressure marine gear oil.
Recommended Applications:• High performance outboard engine lower gear units, including
those operating at high temperatures
Advantages:• Extended drain capability, three times that of conventional
gear oils• Extreme Pressure additives for maximum wear protection
Approvals:• MIL-PRF-2105E• API MT-1
Properties NAUTILUS SYNTHETIC GEAR OIL
Product Code 427-581
Viscosity, cSt40°C 115100°C 16.0
Viscosity Index 162
Pour Point, °C -51
Nautilus Synthetic Gear Oil 1.45.01
SPECIALTY LUBRICANTS
10.17
Nautilus PWC Personal Watercraft Oil 1.47.01
Properties NAUTILUS PWC
Product Code 427-541
API Rating TC
Colour Golden Amber
Viscosity, cSt40°C 57.1100°C 9.46
Brookfield Viscosity, cP-40°C 37,400
Pour Point, °C -57
Flash Point, °C (PMCC) min. 80
TBN-E 1.3
Ash Content, % m 0.10
A high performance, synthetic, 2 stroke personal watercraftengine oil.
Recommended Applications:• High performance, high output 2 stroke personal watercraft
engines• Including those with variable exhaust systems such as RAVE*• Water cooled and air cooled• Pre-mix and direct oil injection systems
Advantages:• Low ash, synthetic formulation minimizes plug fouling and
preignition• Detergent / dispersant formulation minimizes piston and ring
deposits• Improved lubricity and anti-scuffing protection• Superior rust protection• Designed for unleaded gasoline up to 100:1 mixing ratio• Proven performance• No ammonia odour• Reduced exhaust smoke, visible exhaust smoke is essentially
eliminated after warm-up
Approvals:• Exceeds all major Personal Watercraft engine manufacturers
recommendations. Recommended and guaranteed for use inSea-doo, Polaris and Yamaha
• Exceeds highest API-TC, JASO-FC and ISO-EGD standards fordetergency, lubricity, pre-ignition, exhaust system blockage andreduced visible exhaust smoke emission
A premium, mineral based lubricant for 2 stroke air-cooledengines.
Recommended Applications:• Chain saws, lawn equipment, snowblowers• Suitable for pre-mix and direct oil injection• Small engines up to 50:1 fuel to oil ratios• For liquid cooled 2 stroke engines Shell Nautilus Premium
Outboard Motor Oil or Shell Advance Premium SnowmobileOil are preferred
• For high performance applications Shell Advance Snow Ultraand Nautilus Personal Watercraft High Performance SyntheticOil are preferred
Advantages:• Low ash formulation• Excellent piston cleanliness• Reduced spark plug fouling and combustion chamber deposits• High temperature protection• Blue colour for easy of identification in pre-mix fuels
Approvals:• Exceeds API TC classification in piston scuffing, preignition
deposits and ring sticking
Properties XTC 50
Product Code 427-520
API Rating TC
SAE Fluidity/Miscibility Rating 4
Colour Blue
Viscosity, cSt40°C 24.3100°C 4.5
Brookfield Viscosity, cP-40°C 15,000
Pour Point, °C -45
Flash Point PMCC, °C 83COC, °C 110
TBN-E 1.18
Ash Content 0.06
SPECIALTY LUBRICANTS
10.18
XTC 50 - 2 Stroke Engine Oil 1.23.03
Page
Chain Case OilsAdvance 100% Synthetic Chain Case Oil . . . . . . . . . . . 10.6
Compressor OilsClavus AB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7Clavus HFC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8Corena AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.10Corena DE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.12Corena NG (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . . 7.14
Engine OilsAdvance Snow Ultra . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4FormulaShell (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . 3.12FormulaShell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.14Nautilus PWC Personal Watercraft Oil . . . . . . . . . . . . . 10.17Rotella T SB (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . . 3.22
Gear OilsDentax S 50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.29Hyperia S 220 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.28Omala HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.40Omala RL (non EP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.41Spirax HD 75W-90 (Partial Syn) . . . . . . . . . . . . . . . . . 3.26Spirax S 75W-90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.28Tivela . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.53
GreasesAdvance Snow Ultra . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4Darina XL 102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20Retinax TL 00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.28SRS 2000 (Partial Syn) . . . . . . . . . . . . . . . . . . . . . . . . . 6.30Ultragel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.33
Hydraulic OilsTellus HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.48
SYNTHETIC LUBRICANTS
11.1
Table of Contents
SYN
THETIC
LUBES
Page
ASTM TEST METHODS . . . . . . . . . . . . . . . . . . . . . . . . . 12.3
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.4
SAE Crankcase Oil Viscosity Grades . . . . . . . . . . . . . . 12.8API Services - Engine Oils . . . . . . . . . . . . . . . . . . . . . . 12.12
AGMA Gear Lubricant (Viscosity) Classifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.9
SAE Gear Oil Viscosity Grades . . . . . . . . . . . . . . . . . . 12.10API Services - Automotive Gear Oils. . . . . . . . . . . . . . 12.11Engine And Transmission Lubricants,
Recommendations by Specifications and Grade . . 12.13
Grease Thickeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.16Grease Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . 12.17NLGI Grease Grading System . . . . . . . . . . . . . . . . . . . 12.18NLGI Grease Service Classifications . . . . . . . . . . . . . . 12.18
Comparable Viscosity Grades . . . . . . . . . . . . . . . . . . . 12.19Viscosity Conversions (SUS - cSt) . . . . . . . . . . . . . . . . 12.20ISO Viscosity Grades . . . . . . . . . . . . . . . . . . . . . . . . . . 12.21
API Gravities and Densities Table. . . . . . . . . . . . . . . . 12.22Conversion Factors (various units) . . . . . . . . . . . . . . 12.23
Table of Temperature Conversions . . . . . . . . . . . . . . 12.24
APPENDIX
12.1
Appendix Index
APPEN
DIX
APPENDIX
12.2
APPENDIX
12.3
ASTM Test Methods
Test Method NumberAcidity as Acetic Acid . . . . . . . . . . . . . . . . . . . . D 1613Ash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 4530Ash (aviation oils) . . . . . . . . . . . . . . . . . . . . . . . D 482Autoignition Temperature . . . . . . . . . . . . . . . . . D 2155Biodegradability . . . . . . . . . . . . . . . . . . . . . . . . CEC-L-33-T-82Brookfield Viscosity . . . . . . . . . . . . . . . . . . . . . . D 2983CCR Residue . . . . . . . . . . . . . . . . . . . . . . . . . . . D 189CCS (Cold Cranking Simulator,Viscometer) . . . . D 2602Chloride (Coolant) . . . . . . . . . . . . . . . . . . . . . . D 3634Colour, Pt-Co Scale . . . . . . . . . . . . . . . . . . . . . . D 1209Density . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 1298Density (Coolant @ 15.6∞C) . . . . . . . . . . . . . . . D 1122Density (Coolant @ 25∞C) . . . . . . . . . . . . . . . . D 941Dielectric Strength (DISC electrodes) . . . . . . . . D 877Dielectric Strength (VDE electrodes) . . . . . . . . . D 1816Flash Point (Cleveland Open Cup,COC) . . . . . . D 92Flash Point (Pensky Marten Closed Cup, PMCC) . . D 93Flash Point (TAG Closed Cup) . . . . . . . . . . . . . . D 56Fire Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 92Floc Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-86-83,ASHRAEFreeze Point . . . . . . . . . . . . . . . . . . . . . . . . . . . D 2386Freezing Point (Coolant) . . . . . . . . . . . . . . . . . . D 1177FZG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIN 51-354Interfacial Tension . . . . . . . . . . . . . . . . . . . . . . . D 971MRV (Mini Rotary Viscometer) . . . . . . . . . . . . . D4684PH (Coolant) . . . . . . . . . . . . . . . . . . . . . . . . . . . D 1287Pour Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 97Power Factor (electrical) . . . . . . . . . . . . . . . . . . D 924Reserve Alkalinity (Coolant) . . . . . . . . . . . . . . . D 1121Saponification Number . . . . . . . . . . . . . . . . . . . D 94Sulphated Ash . . . . . . . . . . . . . . . . . . . . . . . . . . D 874TAN-C (Total Acid Number) . . . . . . . . . . . . . . . . D 974TAN-E (Total Acid Number) . . . . . . . . . . . . . . . . D 664TBN-E (Total Base Number) . . . . . . . . . . . . . . . . D 2896Timken OK Load. . . . . . . . . . . . . . . . . . . . . . . . D 2782Turbine Oil Stability Test . . . . . . . . . . . . . . . . . . D 943Viscosity (Kinematic) . . . . . . . . . . . . . . . . . . . . D 445Viscosity Index . . . . . . . . . . . . . . . . . . . . . . . . . D 2270Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 1744
Tests Specific to GreasesBase Oil Viscosity . . . . . . . . . . . . . . . . . . . . . . . D 445Coefficient of Friction . . . . . . . . . . . . . . . . . . . . D 5183Dropping Point . . . . . . . . . . . . . . . . . . . . . . . . . D 2265Penetration . . . . . . . . . . . . . . . . . . . . . . . . . . . . D 217Timken OK Load. . . . . . . . . . . . . . . . . . . . . . . . D 2509Water Washout . . . . . . . . . . . . . . . . . . . . . . . . . D 12644-Ball EP - Load Wear Index . . . . . . . . . . . . . . . . D 25964-Ball EP - Weld Load . . . . . . . . . . . . . . . . . . . . . D 25964-Ball Wear Scar . . . . . . . . . . . . . . . . . . . . . . . . . D 2266Water Washout . . . . . . . . . . . . . . . . . . . . . . . . . D1264
APPENDIX
12.4
The descriptions given here are intended to be of a generalnature and may not be an absolute full and scientific explanationof the term.
ACID NUMBER or TOTAL ACID NUMBER - a measure of theacidic nature of an oil. The specific quantity of base required toneutralize the acidic component in an oil. The value typicallyincreases during usage, as acids accumulate in the oil. Measuredin mg. of KOH (base) to neutralize one gram of oil.
AGMA - American Gear Manufacturers Association
ANTI-WEAR ADDITIVE - an additive used in lubricating oilswhich react with the metal surface to reduce the amount ofwear occurring between contacting surfaces. Zinc (dialkyldithiophosphate) is a common example.
API - American Petroleum Institute
ASH or SULPHATED ASH - an indication of the non-combustible residue of an oil. The deposit left after all of thebase oil has been burned away. Metallic detergents and antiwearadditives contribute to the ash content of an oil.
ASTM - American Society for Testing and Materials, establish theASTM Test Methods used by laboratories.
AUTOIGNITION TEMPERATURE - the temperature at which asample of oil can be heated before it will spontaneously ignitewithout a source of ignition. It will be a higher value than theflash or fire points.
BASE NUMBER or TOTAL BASE NUMBER - a measure of thebasic or alkaline nature of an oil. The specific quantity of acidrequired to neutralize the basic component in an oil. The valuedecreases as some of the additives are consumed during use.Measured in mg. of KOH to neutralize one gram of oil.
BASE OIL or BASE STOCK - the oil portion of a lubricating oilor grease. May be mineral or synthetic.
Glossary of Terms
BEARINGS:Rolling Element Bearing or Anti-friction Bearing - anybearing using rollers or balls e.g. ball bearing, spherical,cylindrical, needle. May accept radial and/or thrust loads.Journal Bearing or Plain Bearing - any bearing that does notemploy rolling elements, typically consisting of a shaft rotatingin a cylindrical shell. Also referred to as Shell or Sleeve Bearing.May accept radial or thrust loads.
BROOKFIELD VISCOSITY - a low temperature, low shearviscosity commonly used to measure the performance of gearoils and hydraulic oils.
CCR RESIDUE - Conradson Carbon Residue, the percent ofcoked material left after a sample of oil is exposed to hightemperatures by a prescribed method.
CCS - Cold Cranking Simulator, a low temperature, high shearviscosity commonly used to measure the ability of a motor oil toallow the crankshaft of an engine to spin during start-up.
CENTISTOKE (cSt) - one one-hundredth of a stoke. A commonunit of kinematic viscosity. Equal in value to a mm2/s.
CENTIPOISE (cP) - one one-hundredth of a poise. A commonunit of absolute viscosity. Brookfield, Cold Cranking Simulatorand Mini Rotary Viscometer all measure absolute viscosity andthe resulting values are given in centipoise. May be convertedto centistoke by dividing by the density of the oil (at the sametemperature). Equal in value to a milli Pascal second (mPa.s).
CGSB - Canadian General Standards Board, develops standardsfor products and test methods specific to Canada.
CHANNEL POINT - the lowest temperature at which a paddlecan be pulled through a sample of cold oil and the walls createdby the paddle due not flow back into the channel (within aprescribed time)
COMPOUNDED OIL - an oil containing either natural orsynthetic fatty materials as additives
DEMULSIBILITY - the ability of an oil to separate (release ordrop) water from the oil.
APPENDIX
12.5
Glossary of Terms
APPENDIX
12.6
DROPPING POINT - the highest temperature to which a greasecan be heated before a drop of oil separates (and drops) fromthe grease (under prescribed conditions).
EP - Extreme Pressure additive. An additive used in lubricatingoils or greases which react with the metal surface to reduce theamount of adhesion or cold-welding which may occur betweencontacting surfaces under severe loads or shock loading.Sulphur-phosphorous chemicals are a common example used ingear oils.
FOUR (4) BALL TESTER - one of two laboratory machines. The4 Ball Wear Tester which indicates the wear protection offeredby a lubricant by measuring a scar diameter on four steel balls.The 4 Ball EP Tester which indicates the extreme pressure loadcarrying capacity of a lubricant. The test method determines aWeld Load and a calculated Load Wear Index (LWI).
FLASH POINT - the lowest temperature at which an oil createsenough vapour above the surface of the oil to yield acombustible mixture which will ignite or explode in thepresence of a spark, but insufficient vapour to sustain a flame.COC - Cleveland Open Cup Method, used for lubricating oils.PMCC - Pensky-Martens Closed Cup Method, used for fuel oils orlubricants that contain lighter solvent-like materials.TAGCC - Tag Closed Cup Method, used for solvents.
FLOC POINT - used to indicate the lowest temperature that arefrigeration oil can be cooled before wax or other componentsbegin to solidify.
ISO - International Standards Organization
LUBRICANT - may be either an oil or a grease or a solid used toreduce friction between two surfaces.
MINERAL OIL - a base oil (base stock) derived from crude oil ata refinery by separation and purification processes includingcombinations of fractionation, solvent extraction, hydrofinishing,hydrotreating, hydrocracking, dewaxing.
MRV - Mini Rotary Viscometer, a low temperature, low shearviscosity commonly used to measure the ability of an oil to flowtoward (flood) the suction of an automotive engine’s oil pump.It is used to predict and prevent oil starvation during enginestart-up.
Glossary of Terms
NEUTRALIZATION NUMBER - may be either the acid numberor base number of an oil. The amount of acid or base requiredto neutralize an oil.
NLGI - National Lubricating Grease Institute.
PENETRATION - the consistency or hardness of a grease. Thepenetration of a cone into a sample of grease indicates its’hardness and is used to assign the NLGI grease grade numberse.g. a #2 grade grease.
PROCESS OIL - typically a base oil used in a manufacturingprocess and not used directly for lubrication e.g. rubberextenders, dedusting.
R&O - a rust and oxidation inhibited lubricating oil. It maycontain an antifoam additive but will not contain an antiwear orEP additive.
SAE - Society of Automotive Engineers.
SOLVENT EXTRACTION - a refining process for base oils usedto remove the undesirable components.
STLE - Society of Tribologists and Lubrication Engineers
SULPHATED ASH - See Ash.
SYNTHETIC - man-made, synthesized (not naturally occurring)base oil. Various chemical types exist.
SYNTHETIC BLEND - an oil containing both mineral oil basestock and synthetic oil base stock.
TIMKEN OK LOAD - a measure of the extreme pressure (EP)properties of an oil or grease. The “OK Load” is the heaviest loadthat the film of lubricant can support without scoring. Testresults can vary significantly.
TOTAL ACID NUMBER (TAN) - See Acid Number
TOTAL BASE NUMBER (TBN) - See Base Number
APPENDIX
12.7
Glossary of Terms
LOW
TEM
P. V
ISCO
SITI
ESH
IGH
TEM
PERA
TURE
VIS
COSI
TIES
Visc
osity
CC
S C
rank
ing
MRV
Pum
ping
M
in. K
inem
atic
Max
. Kin
emat
icH
igh
Shea
r (c
P) m
in.
Gra
deVi
scos
ity
(cP)
Max
@ °
C(c
St) M
ax @
°C
Visc
osity
@
150
°C &
106 s
-1
(cP)
max
. @ °
C(c
St) @
100
°C
0W6,
200
@ -
3560
,000
@ -
403.
8-
--
-
5W6,
600
@ -
3060
,000
@ -
353.
8-
--
-
10W
7,00
0 @
-25
60,0
00 @
-30
4.1
- -
- -
15W
7,00
0 @
-20
60,0
00 @
-25
5.6
- -
- -
20W
9,50
0 @
-15
60,0
00 @
-20
5.6
- -
- -
25W
13,0
00 @
-10
60,0
00 @
-15
9.3
- -
- -
20-
--
-5.
6<
9.3
2.6
30-
--
-9.
3<
12.5
2.9
40-
--
-12
.5<
16.3
3.3
(0W
-40,
5W
-40,
10W
-40)
40-
--
-12
.5<
16.3
3.7
(15W
-40,
20
W-4
0, 2
5W-4
0, 4
0)
50-
--
-16
.3<
21.9
3.7
60-
--
-21
.9<
26.1
3.7
APPENDIX
12.8
SAE Viscosity Classification for Crankcase Oils*
* A
ll va
lues
are
crit
ical
spe
cific
atio
ns a
s de
fined
by
AST
M D
324
4
SAE
J-30
0 (D
ec 9
9 Re
visi
on)
VISCOSITY RANGES FOR INDUSTRIAL GEAR OILS - AGMA 250.04
AGMA No. VISCOSITY RANGE COMPARABLECSt. @ 40°C ISO GRADE
1 41.4 - 50.6 46
2 & 2 EP* 61.2 - 74.8 68
3 & 3 EP 90.0 - 110 100
4 & 4 EP 135 - 165 150
5 & 5 EP 198 - 242 220
6 & 6 EP 288 - 352 320
7 Comp.** & 7 EP 414 - 506 460
8 Comp. & 8 EP 612 - 748 680
8A Comp. & 8A EP 900 - 1000 1000
*EP designates extreme pressure inhibited gear oil grades.
**Comp. designates oil compounded with 3% to 10% fatty or synthetic
fatty components.
APPENDIX
12.9
AGMA Gear Lubricant Classifications
SAE
Gea
r O
il V
isco
sity
Gra
des
M
IL -
L -
210
5D G
rade
s
PRO
PERT
Y75
W80
W85
W90
140
250
75W
80W
-90
85W
-140
Visc
osity
, cSt
100°
C M
in.
4.1
711
13.5
24.0
414.
113
.524
.0M
ax.
24.5
41.0
24.0
41.0
Max
. Tem
p (C
) for
150,
000
cP V
isc.
-40
-26
-12
- -
- -
- -
-40
-26
-12
Cha
nnel
Poi
nt, °
CM
ax.
-45
-35
-20
Flas
h Po
int,
°CM
ax.
150
165
180
APPENDIX
12.10
Physical Requirements for Automotive Gear Lubricants
API - GL-1 to GL-3Designates the type of service characteristic of automotivespiral-bevel and worm-gear axles and some manually operatedtransmissions operating under mild or moderate conditions ofpressures and sliding velocities.
API - GL-4Designates the type of service characteristic of gears,particularly hypoid in passenger cars and other automotive typeequipment operating under high-speed, low torque, and low-speed, high torque conditions.
API - GL-5Similar to GL-4 but designed to protect automotive equipmentoperated under high-speed shock-load.
API GL-6Obsolete
MT-1Recently adopted standard. Designates use in non-synchronizedmanual transmissions.
PG-2 (Proposed Classification)Developed to replace API - GL5. Shell Spirax HD gear lubricantsare approved against this standard when it becomes official.
APPENDIX
12.11
API Services - Automotive Gear Oils
APPENDIX
12.12
“S” - SERVICE (Gasoline)
API SERVICES SA to SG:ObsoleteThese service designations are an alphabetical evolution ofprotection levels originated back in the early 1960’s. As gasolineengines became more severe, better motor oils were developed.
API SERVICE SH:Category for 1994 model (and later) warranty requirements.
API SERVICE SJ:Category for 1996 model (and later) warranty requirements.
API SERVICE SL:Category for 2001 model (and later) warranty requirements.Thecurrent service level that ensures optimum gasoline engine life.
“C” - SERVICE (Diesel)
API SERVICES CA to CE:ObsoleteSimilar to “S” service designations is protection level evolutionbut pertaining mainly to diesel engines.
API SERVICE CF-2:1994 severe duty 2-cycle diesel engines.
API SERVICE CF-4:Severe duty turbocharged 4-cycle diesel engines: highestprotection against high and low temperature deposits, wear,corrosion, especially late model (since 1988) lower emissionengines: Mack EO-K/2, Cummins NTC 400, Caterpillar 1-K.
API SERVICE CG-4:Enhanced protection for high speed 4-cycle diesel engines tomeet 1994 exhaust emission standards.
API SERVICE CH-4Enhanced protection for high speed 4-cycle diesel engines tomeet 1998 exhaust emission standards.
API Services - Engine Oils
APPENDIX
12.13
Engine and Transmission LubricantsRecommendations by Specifications and Grade
Prod
uct
Rote
lla T
Pl
us15
W-40
Rote
lla T
w
ith X
LA10
W-30
15W-
40Ro
tella
T10
W20
W-20
30 40 50Ro
tella
T
SBSy
n. B
lends
: 10
W-40
0W-3
05W
-30
100%
Syn.:
0W
-40
API
CD R R R R R R R R R R R
API
CD-II R R R
API
CE R R R R R R R
API
CF R R R R R R R R R R R R
API
CF-2 R R R
API
CG-4 R R R R R R R
API
CH-4 R R R R
MAC
KE0
-M R R R R
MAC
KE0
-MPL
US R R R R
Cum
min
sCE
S20
071
R R R R
Cum
min
sCE
S20
076
R R R R
Volv
oVD
S R R R
Volv
oVD
S-2
R R R
API
SH R R R R R R R
API
SJ R R R R R
API
SLIL
SAC
GF-3
Ener
gy
cons
ervin
gAl
lison
C-4 R R R R R R R R R R R
API
CF-4 R R R R R R R
R=RE
CO
MM
END
ED F
OR
THE
CO
RRES
PON
DIN
G S
PEC
IFIC
ATIO
N C
ATEG
ORY
.
REC
OM
MEN
DA
TIO
NS
- D
IESE
LREC
OM
MEN
DA
TIO
NS
- G
ASO
LIN
E
APPENDIX
12.14
Engine and Transmission LubricantsRecommendations by Specifications and Grade
Prod
uct
Form
ulaSh
ell10
0%Sy
nthe
tic5W
-30
10W-
30
Form
ulaSh
ellSy
nthe
tic
Blen
d5W
-20
5W-3
010
W-30
20W-
50
Form
ulaSh
ell5W
-30
10W-
3010
W-40
30 40
API
CD R R
API
CD-II
API
CEAP
ICF R R
API
CF-2
API
CG-4
API
CH-4
MAC
KE0
-M
MAC
KE0
-MPL
US
Cum
min
sCE
S20
071
Cum
min
sCE
S20
076
Volv
oVD
SVo
lvo
VDS-
2AP
ISH R R R R R R R R R R
API
SJ R R R R R R R R R R
API
SL R R R*
R R R R R R
ILSA
CGF
-3 R R R*
R R R R
Ener
gy
cons
ervin
g
R R R*
R R R R
Allis
onC-
4AP
ICF
-4
R=RE
CO
MM
END
ED F
OR
THE
CO
RRES
PON
DIN
G S
PEC
IFIC
ATIO
N C
ATEG
ORY
.*
YOU
MU
STC
ON
SULT
YO
UR
OW
NER
S’ M
AN
UA
L FO
R A
PPLIC
ABI
LITY
OF
THIS
PRO
DU
CT.
REC
OM
MEN
DA
TIO
NS
- D
IESE
LREC
OM
MEN
DA
TIO
NS
- G
ASO
LIN
E
APPENDIX
12.15
Engine and Transmission LubricantsRecommendations by Specifications and Grade
Prod
uct
Shell
Fleet
10W-
3015
W-40
10W 30
Prod
uct
Dona
xTC TD TD
L
TG
API
CD R R R R
API
CD-II R
API
CE R R R
API
CF R R R R
API
CF-2 R
API
CG-4 R R
API
CH-4 R R
MAC
KE0
-M R R
MAC
KE0
-MPL
US R R
Cum
min
sCE
S20
071
R R
Cum
min
sCE
S20
076
R R
Volv
oVD
S R
Volv
oVD
S-2
API
SH R R
API
SJ R
API
SLIL
SAC
GF-3
Ener
gy
cons
ervin
gAl
lison
C-4 R R R R
API
CF-4 R R
Allis
onC-
4 R R R R
Cat
TO-4
R
Cat
TO-2 R
TRAN
SM
ISSIO
N O
ILS
R=RE
CO
MM
END
ED F
OR
THE
CO
RRES
PON
DIN
G S
PEC
IFIC
ATIO
N C
ATEG
ORY
.
REC
OM
MEN
DA
TIO
NS
- D
IESE
LREC
OM
MEN
DA
TIO
NS
- G
ASO
LIN
E
Greases generally consist of a base oil with additives plus athickening agent to create the semi-solid nature of a grease. Thethickeners may contain lithium, calcium, aluminum or bariumcomponents or be made of polyurea or clay etc. “Complex”greases are a newer type of thickener technology (than “SimpleSoap”) and tend to improve the high temperature capability ofthe grease.
About Shell Canada’s major greases:
Lithium soap greases have been around for many years andtheir multipurpose nature allows them to satisfy over 80% of allapplications. However, for severe applications, othertechnologies may have advantages.
Lithium Complex greases maintain most of the multipurposenature of lithium greases but perform better at hightemperatures and can have better mechanical stability. Ingeneral,“Complex” greases tend to have greater compatibilityproblems with other greases than conventional soap greases.
Calcium soap greases have better water resistance andmechanical stability than lithium greases, but are not suitable forhigh temperatures.
Mixed Lithium Calcium greases combine the advantage ofboth technologies, with excellent high temperature andmechanical stability properties.
“Microgel” clay greases are excellent multipurpose productswith extreme high temperature and mechanical stabilitycapabilities.
Polyurea greases have excellent long life and natural antiwearproperties but are better suited to some specialized applicationsrather than multipurpose use.
APPENDIX
12.16
Grease Thickeners
Different greases may not be compatible with each other.Incompatibility may be caused by the different thickeningagents used or by the different additives used in greases.Thickener incompatibility usually results in the mixturebecoming thinner than anticipated. Other detrimental effectsare possible.
Due to the complexity of this problem and its potentialseriousness, and as opinions vary as to which types of greasesare compatible, we have chosen not to include a greasecompatibility chart.
“RULE OF THUMB”As a general rule of thumb, it is best to assume that all differenttypes and brands of greases are NOT COMPATIBLE with eachother. When changing from one grease to another it is best tocompletely clean the grease cavity and lubricated surfaces. Ifthis is not possible, a thorough purge of the system should beperformed.
Incompatibility problems are more critical in equipmentoperating at higher temperatures, speeds and loads.
SHELL CANADA’S GREASESThe Lithium, Calcium and mixed Lithium-Calcium greases, asmanufactured by Shell Canada, are compatible with each otherand our “Microgel” clay based greases. Clay based greases can beincompatible with a wide range of thickeners and additivetechnologies but Shell Canada’s Research has improved thistechnology beyond that of other clay based greases, such thatcompatibility problems are much less of an issue.
For further information on specific grease compatibility, contactthe Shell Helps Centre at 1-800-661-1600.
APPENDIX
12.17
Grease Compatibility
NLGI GREASE SERVICE CLASSIFICATIONS
NLGI Grade # WORKED PENETRATION (10th of mm) @ 25°C
000 445 to 475 (measured with alternate cone)(very soft, semi-fluid)
00 400 to 430 (measured with alternate cone)
0 355 to 385
1 310 to 340
2 265 to 295
3 220 to 250
4 175 to 205
5 130 to 160
6 85 to 115 (very hard, block grease)
Note: Gaps exist (in the penetration numbers) between the officialNLGI grades. This allows for unofficial half grades e.g.) a greasewith a penetration of 300mm could be designated as a 1.5 grade.
NLGI GREASE SERVICE CLASSIFICATIONS
LA - (Chassis) Mild duty, frequent relubrication
LB - (Chassis) High loads, water exposure,infrequent relubrication
GA - (Wheel Bearings) Mild duty
GB - (Wheel Bearings) Moderate duty, typical of most vehicles
GC - (Wheel Bearings) Severe duty, high temperature,frequent stop and go service
APPENDIX
12.18
NLGI Grease Grading System/Service Classifications
APPENDIX
12.19
Comparable Viscosity Grades
900
850
775
700
625
550
500
450
400
365
315
280
ViscositycSt.
@ 40°C
205
175
140
115
85
60
40
30
20
10
0
50
42
40
38
36
34
32
30
28
26
24
22
ViscositycSt.@ 100°C
18
16
14
12
10
8
6
4
2
0ISO AGMA SAE SAE
Grade No. Gear MotorOil Oil
680
460
320
220
150
100
68
46
32
22
1
2
3
4
5
6
7
8
140
90
85W
80W
75W
50
40
30
20
10W
5W
(Older SUS or SSU to current cSt. or mm2/s)
Assumes that viscosities are at the same temperature and theViscosity Index is 95.
35 SSU ~ 2.5 cSt 550 SSU ~ 119 cSt40 SSU ~ 4.2 cSt 600 SSU ~ 129 cSt45 SSU ~ 5.8 cSt 650 SSU ~ 140 cSt50 SSU ~ 7.4 cSt 700 SSU ~ 151 cSt55 SSU ~ 8.8 cSt 750 SSU ~ 162 cSt60 SSU ~ 10.4 cSt 800 SSU ~ 173 cSt65 SSU ~ 11.8 cSt 850 SSU ~ 183 cSt70 SSU ~ 13.1 cSt 900 SSU ~ 195 cSt75 SSU ~ 14.4 cSt 1,000 SSU ~ 216 cSt80 SSU ~ 15.6 cSt 1,100 SSU ~ 237 cSt85 SSU ~ 17.0 cSt 1,200 SSU ~ 259 cSt90 SSU ~ 18.3 cSt 1,300 SSU ~ 280 cSt95 SSU ~ 19.4 cSt 1,400 SSU ~ 302 cSt
100 SSU ~ 20.6 cSt 1,500 SSU ~ 324 cSt110 SSU ~ 22.9 cSt 1,600 SSU ~ 345 cSt120 SSU ~ 25.2 cSt 1,700 SSU ~ 368 cSt130 SSU ~ 27.5 cSt 1,800 SSU ~ 389 cSt140 SSU ~ 29.7 cSt 1,900 SSU ~ 411 cSt150 SSU ~ 31.9 cSt 2,000 SSU ~ 432 cSt160 SSU ~ 34.2 cSt 2,100 SSU ~ 453 cSt170 SSU ~ 36.5 cSt 2,200 SSU ~ 475 cSt180 SSU ~ 38.6 cSt 2,300 SSU ~ 496 cSt190 SSU ~ 40.8 cSt 2,400 SSU ~ 518 cSt200 SSU ~ 43.0 cSt 2,500 SSU ~ 539 cSt225 SSU ~ 48.5 cSt 2,600 SSU ~ 562 cSt250 SSU ~ 53.8 cSt 2,700 SSU ~ 584 cSt275 SSU ~ 59.2 cSt 2,800 SSU ~ 605 cSt300 SSU ~ 64.8 cSt 2,900 SSU ~ 627 cSt325 SSU ~ 70.1 cSt 3,000 SSU ~ 648 cSt350 SSU ~ 75.6 cSt 3,500 SSU ~ 756 cSt375 SSU ~ 81.1 cSt 4,000 SSU ~ 864 cSt400 SSU ~ 86.5 cSt 5,000 SSU ~ 1,080 cSt425 SSU ~ 92.0 cSt 6,000 SSU ~ 1,296 cSt450 SSU ~ 97.4 cSt 7,000 SSU ~ 1,509 cSt475 SSU ~ 102.7 cSt 8,000 SSU ~ 1,726 cSt500 SSU ~ 108.0 cSt 9,000 SSU ~ 1,943 cSt
APPENDIX
12.20
Viscosity Conversions
VISCOSITY SYSTEM FOR INDUSTRIAL LUBRICANTS - ASTM D-2422-86
Mid-Point Minimum Maximum AGMAISO Viscosity Of Of (Gear)
Grade CSt @ 40°C Grade Grade Number
VG 2 2.2 1.98 2.4
VG 3 3.2 2.88 3.52
VG 5 4.6 4.14 5.06
VG 7 6.8 6.12 7.48
VG 10 10 9 11
VG 15 15 13.5 16.5
VG 22 22 19.8 24.2
VG 32 32 28.8 35.2
VG 46 46 41.4 50.6 1
VG 68 68 61.2 74.8 2
VG 100 100 90 110 3
VG 150 150 135 165 4
VG 220 220 198 242 5
VG 320 320 288 352 6
VG 460 460 414 506 7
VG 680 680 612 748 8
VG 1000 1000 900 1100 8A
VG 1500 1500 1350 1650
APPENDIX
12.21
ISO Viscosity Grades
Note: All conversions are at 15.6°C.
API Density API Density Gravity (kg/L) Gravity (kg/L)
0 1.074 21 0.926
1 1.066 22 0.920
2 1.058 23 0.914
3 1.050 24 0.908
4 1.042 25 0.902
5 1.034 26 0.896
6 1.027 27 0.891
7 1.020 28 0.885
8 1.012 29 0.880
9 1.005 30 0.874
10 0.998 31 0.869
11 0.991 32 0.864
12 0.984 33 0.858
13 0.977 34 0.853
14 0.970 35 0.848
15 0.964 36 0.843
16 0.957 37 0.838
17 0.951 38 0.833
18 0.944 39 0.828
19 0.938 40 0.823
20 0.932 41 0.818
APPENDIX
12.22
API Gravities and Densities
Linear Measurement:
1 inch = 25.4 mm 1 mm = 0.03937 inches1 foot = 0.3048 meters 1 cm = 0.3937 inches1 yard = 0.9144 meters 1 m = 39.37 inches1 mile = 1.6093 km 1 km = 0.6214 miles1 nautical mile = 1.852 km
Area Measurement:
1 sq. inch = 6.4516 sq. cm 1 sq. cm = 0.1550 sq. inches1 sq. foot = 0.09290 sq. m 1 sq. m = 10.7639 sq.feet1 sq. yard = 0.8361 sq. m 1 sq. m = 1.1960 sq. yards1 sq. mile = 2.5899 sq. km 1 sq. km = 0.3861 sq. miles1 acre = 0.4047 hectares 1 hectare = 2.471 acres
Cubic Measurement:
1 cu. inch = 16.3871 cc (ml) 1 cc (ml) = 0.061024 cu. inches1 cu. foot = 0.02832 cu. m 1 cu. m = 35.3147 cu. feet1 cu. foot = 28.3161 litres 1 litre = 0.0353 cu. feet1 cu. yard = 0.7646 cu. m 1 cu. m = 1.3080 cu. yards
Volume Conversions:
1 Imp.gallon = 4.546 litres = 1.20092 U.S. gallons= 0.00456 cubic metres = 0.028594 Bbls (barrels)= 0.160544 cu.feet
1 litre = 0.21998 Imp. gallons = 0.26417 U.S. gallons= 0.001000 cubic metres = 0.006290 Bbls.= 0.0353157 cu. feet
1 cu. m = 1000 litres1 cu. inch = 16.4 cc (ml)1 Bbl. = 159 litres
Temperature Conversion:
°F = (°C x 9/5) + 32°C = (°F - 32) x 5/9
Pressure Conversion:
100 kPa = 14.504 PSI = 1 bar
APPENDIX
12.23
Conversion Factors
APPENDIX
12.24
Table of Temperature Conversions
° C ° F ° C ° F ° C ° F ° C ° F
-70 -94.0 -46 -50.8 -22 -7.6 2 35.6
-69 -92.2 -45 -49.0 -21 -5.8 3 37.4
-68 -90.4 -44 -47.2 -20 -4.0 4 39.2
-67 -88.6 -43 -45.4 -19 -2.2 5 41.0
-66 -86.8 -42 -43.6 -18 -0.4 6 42.8
-65 -85.0 -41 -41.8 -17 1.4 7 44.6
-64 -83.2 -40 -40.0 -16 3.2 8 46.4
-63 -81.4 -39 -38.2 -15 5.0 9 48.2
-62 -79.6 -38 -36.4 -14 6.8 10 50.0
-61 -77.8 -37 -34.6 -13 8.6 11 51.8
-60 -76.0 -36 -32.8 -12 10.4 12 53.6
-59 -74.2 -35 -31.0 -11 12.2 13 55.4
-58 -72.4 -34 -29.2 -10 14.0 14 57.2
-57 -70.6 -33 -37.4 -9 15.8 15 59.0
-56 -68.8 -32 -25.6 -8 17.6 16 60.8
-55 -67.0 -31 -23.8 -7 19.4 17 62.6
-54 -65.2 -30 -22.0 -6 21.2 18 64.4
-53 -63.4 -29 -20.2 -5 23.0 19 66.2
-52 -61.6 -28 -18.3 -4 24.8 20 68.0
-51 -59.8 -27 -16.6 -3 26.6 21 69.8
-50 -58.0 -26 -14.8 -2 28.4 22 71.6
-49 -56.2 -25 -13.0 -1 30.2 23 73.4
-48 -54.4 -24 -11.2 0 32.0 24 75.2
-47 -52.6 -23 -9.4 1 33.8 25 77.0
APPENDIX
12.25
Table of Temperature Conversions
° C ° F ° C ° F ° C ° F ° C ° F
26 78.8 50 122.0 74 165.2 98 208.4
27 80.6 51 123.8 75 167.0 99 210.2
28 82.4 52 125.6 76 168.8 100 212.0
29 84.2 53 127.4 77 170.6 101 213.8
30 86.0 54 129.2 78 172.4 102 215.6
31 87.8 55 131.0 79 174.2 103 217.4
32 89.6 56 132.8 80 176.0 104 219.2
33 91.4 57 134.6 81 177.8 105 221.0
34 93.2 58 136.4 82 179.6 106 222.8
35 95.0 59 138.2 83 181.4 107 224.6
36 96.8 60 140.0 84 183.2 108 226.4
37 98.6 61 141.8 85 185.0 109 228.2
38 100.4 62 143.6 86 186.8 110 230.0
39 102.2 63 145.4 87 188.6 111 231.8
40 104.0 64 147.2 88 190.4 112 233.6
41 105.8 65 149.0 89 192.2 113 235.4
42 107.6 66 150.8 90 194.0 114 237.2
43 109.4 67 152.6 91 195.8 115 239.0
44 111.2 68 154.4 92 197.6 116 240.8
45 113.0 69 156.2 93 199.4 117 242.6
46 114.8 70 158.0 94 201.2 118 244.4
47 116.6 71 159.8 95 203.0 119 246.2
48 118.4 72 161.6 96 204.8 120 248.0
49 120.2 73 163.4 97 206.6 121 249.8
APPENDIX
12.26
Table of Temperature Conversions
° C ° F ° C ° F ° C ° F ° C ° F
122 251.6 146 294.8 170 338.0 194 381.2
123 253.4 147 296.6 171 339.8 195 383.0
124 255.2 148 298.4 172 341.6 196 384.8
125 257.0 149 300.2 173 343.4 197 386.6
126 258.8 150 302.0 174 345.2 198 388.4
127 260.6 151 303.8 175 347.0 199 390.2
128 262.4 152 305.6 176 348.8 200 392.0
129 264.2 153 307.4 177 350.6 201 393.8
130 266.0 154 309.2 178 352.4 202 395.6
131 267.8 155 311.0 179 354.2 203 397.4
132 269.6 156 312.8 180 356.0 204 399.2
133 271.4 157 314.6 181 357.8 205 401.0
134 273.2 158 316.4 182 359.6 206 402.8
135 275.0 159 318.2 183 361.4 207 404.6
136 276.8 160 320.0 184 363.2 208 406.4
137 278.6 161 321.8 185 365.0 209 408.2
138 280.4 162 323.6 186 366.8 210 410.0
139 282.2 163 325.4 187 368.6 211 411.6
140 284.0 164 327.2 188 370.4 212 413.6
141 285.8 165 329.0 189 372.2 213 415.4
142 287.6 166 330.8 190 374.0 214 417.2
143 289.4 167 332.6 191 375.8 215 419.0
144 291.2 168 334.4 192 377.6 216 420.8
145 293.0 169 336.2 193 379.4 217 422.6
Product Page
Advance Premium Snowmobile . . see Shell Advance Prem. Snowmobile
Advance 100% Synthetic Chain Case Oil . . . . . . . . . . . . . 10.6 Advance Snow Ultra. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4Advance Snow Ultra Grease . . . . . . . . . . . . . . . . . . . . . . . 6.4AeroShell Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7AeroShell Greases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6AeroShell Oils (non-dispersant) . . . . . . . . . . . . . . . . . . . . 4.3AeroShell Turbine Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8AeroShell Oil W 15W-50 (semi-synthetic) . . . . . . . . . . . . . 4.5AeroShell Oil W 100 Plus . . . . . . . . . . . . . . . . . . . . . . . . . 4.6AeroShell Oil W Piston Engine Oils (dispersant). . . . . 4.4Albida LC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8Alexia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2Alvania EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.12Alvania EP D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.10Alvania 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.14Argina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3Caprinus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4Cardura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.15Cassis A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4Chain Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7Classlube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5Clavus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6Clavus AB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7Clavus HFC 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8Corena AS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.10Corena DE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.12Corena NG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.14Corena P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.16Corena S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.18Cyprina RA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.17Darina AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.18Darina XL EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.20Decol H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.19Delima. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.20Delima R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.21Dentax 80W-90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.26Dentax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.29
PRODUCT INDEX
13.1
PRO
DU
CT IN
DEX
Product Page
Diala A and AX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.22Diamond Drill Rod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.22Donax CFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11Donax TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6Donax TD and TDL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8Donax TF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9Donax TG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10Dromus B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.24Dursol K1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.23Form Oil 46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.25FormulaShell Engine Oils (mineral and synthetic blend). . 3.12FormulaShell Engine Oils (100% synthetic) . . . . . . . . . . . 3.14FormulaShell SAE 30 and SAE 40 . . . . . . . . . . . . . . . . . . . 3.15Gadinia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6Garia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.26Geartherm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.27Hyperia S. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.28Indusol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Shell Indusol
Malleus GL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.24Malleus TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.26Melina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7Morlina . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.30Mysella . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.31Nautilus Premium Outboard Motor Oil . . . . . . . . . . . . . . 10.8Nautilus Biodegradable Bilge Cleaner . . . . . . . . . . . . . . . . 10.13Nautilus Biodegradable Boat Cleaner . . . . . . . . . . . . . . . . 10.14Nautilus Biodegradable Outboard Motor Oil. . . . . . . . . . . 10.9Nautilus 4 Stroke Engine Oils. . . . . . . . . . . . . . . . . . . . . . 10.10Nautilus Jet Pump Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.15Nautilus Marine Gear Oil . . . . . . . . . . . . . . . . . . . . . . . . . 10.12Nautilus Personal Watercraft Oil . . . . . . . . . . . . . . . . . . . . 10.17Nautilus Synthetic Gear Oil . . . . . . . . . . . . . . . . . . . . . . . 10.16No Fire WG 200R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.36Omala . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.38Omala HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.40Omala RL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.41Ossagol C Moly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.27Pella A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.42Retinax TL 00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.28
PRODUCT INDEX
13.2
PRODUCT INDEX
13.3
Product Page
Rotella ELC Extended Life Coolant . . . . . . . . . . . . . . . . . 3.5Rotella T Single Grade . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.18Rotella T Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.24Rotella T SB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.22Rotella T with XLA (multi-grade) . . . . . . . . . . . . . . . . . . . 3.20Sawguide Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.43Shell Advance Premium Snowmobile . . . . . . . . . . . . . . . . 10.3Shell Fleet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16Shell Fluid FM 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3Shell FM Grease 1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.16Shell FR-N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.34Shell Indusol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.29Shell LGF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7Shell Naturelle HF-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.32Shell Naturelle HF-M . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.33Shell Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.58Shellflex Naphthenic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2Shellflex Paraffinic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4Shellzone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4Sirius FB Oil 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.8Spirax HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.26Spirax S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.28SRS 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.30Stringol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.44Surstay EP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.32Tellus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.46Tellus 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.45Tellus HD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.48Tellus T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.50Thermia C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.52Tivela. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.53Tonna V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.54Torcula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.56Turbo T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see Shell Turbo T
Ultragel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.33Valvata . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.60Vitrea 22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.61VSI 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.62XTC-50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.18
Contact us formore information
on Shell Lubricants:
Shell Helps Centre1-800-661-1600
www.shell.ca
275-S-000277