harmonics and filters - · pdf fileharmonics and filters book referred by : 1. hvdc power...
TRANSCRIPT
HARMONICS AND FILTERS
Book Referred by :
1. HVDC Power Transmission by K.R Padiyar
UNIT 4
www.eeecube.com
www.eeecube.com
INTRODUCTION
• HVDC converters introduce both AC and DC harmonics which are injected into the ACsystem .
• There are several problems associated with the injection of harmonics are listed below:
• Telephone interference
• Extra power losses and consequent heating in machines & capacitors connected in the S/Y
• Overvoltage's due to resonances
• Instability of converter controls, primarily with Individual Phase Control (IPC) scheme of firing pulse generation
• Interference with ripple control systems used in load management
www.eeecube.com
www.eeecube.com
GENERATION OF HARMONICS
• Characteristics Harmonics
• Non Characteristics Harmonics
www.eeecube.com
www.eeecube.com
CHARACTERISTICS HARMONICS
• The characteristic harmonics are harmonics which are always present even underideal operation - balanced AC voltages, symmetric three phase network andequidistant pulses.
• In the converter, the DC current is assumed to be constant.
• In this case, there are Harmonics in AC current of the order
ℎ = 𝑛𝑝 ± 1 -------------------------- (1)
Where, p is the pulse number
n is any integer
www.eeecube.com
www.eeecube.com
• There are Harmonics in converter DC voltage of the order
ℎ = 𝑛𝑝 -------------------------- (2)
• When reactor smoothing is used then harmonics in the dc current also of the order given by equation 2
www.eeecube.com
www.eeecube.com
CALCULATION OF CHARACTERISTICS AC HARMONICS
• Consider a 12 pulse converter
• From fig, Neglect over lap, waveform for 𝑖𝐴1and 𝑖𝐴2are shown
• For convenience, the ordinate axis is chosen that the waveform have even symmetry [𝜔𝑡 = 0]
• The waveform has half wave symmetry so that even harmonics are zero
• Hence we can express 𝑖𝐴1 𝑎𝑠,
www.eeecube.com
www.eeecube.com
• we can express current 𝑖𝐴2 𝑎𝑠,
www.eeecube.com
www.eeecube.com
• So the magnitude of the characteristics harmonics are shown below
www.eeecube.com
www.eeecube.com
From the Fourier series analysis of DC voltage waveform, We can obtain
DC VOLTAGE HARMONICS
www.eeecube.com
www.eeecube.com
NON CHARACTERISTICS HARMONICS
• The harmonics of the order other than the characteristic harmonics are termed as non-characteristic.
• These are due to
(i) Imbalance in the operation of two bridges forming a 12 pulse converter
(ii) Firing angle errors
(iii) Unbalance and distortion in AC voltages and
(iv) unequal transformer leakage impedances.
www.eeecube.com
www.eeecube.com
• The harmonics produced due to the first cause are termed as residual harmonics.
• These mainly due to the difference in the firing angles in the two bridges which lead to unequal cancellation of the harmonics of order 5. 7, 17, 19, etc.
• The unequal leakage impedances of the two converter transformers feeding the two bridges also lead to residual harmonics.
• The last three causes can lead to the generation of triplen and even harmonics and their analysis is complex
www.eeecube.com
www.eeecube.com
Effect of Firing Angle Errors
• It is convenient to neglect overlap in the analysis.
• The errors in the firing angles can be due to nature of the control system.
• The equidistant pulse control scheme ideally, has inherent errors except due to thejitter.
• To study the effect of firing angle errors, we will simplify the analysis byconsidering a single Graetz bridge fed from a star/star connected transformer,
• We consider the error 휀𝑗 as the delay in the firing of valve j from the instant
corresponding to the desired value of the firing angle
www.eeecube.com
www.eeecube.com
• There is no loss of generality in assuming the firing error for valve 1 is zero as theanalysis
• applies to steady state conditions, where it is assumed that the waveform isperiodic with the
• Fundamental frequency of 𝜔. Thus, there are five independent parameters £2, £3,£4. £5, and £6
• To illustrate the analysis. we will consider an example with following data:
휀3 = 휀5 = 0,휀2 = 휀4 = 휀6 = 휀
The waveform of the phase similar to the waveform of 𝑖𝐴1,to analyze the waveform consider the sum of two waveform and the other represents the effect of firing errors
𝑖𝑎 𝑡 = 𝑖𝑎𝑜 𝑡 + ∆𝑖𝑎(𝑡)𝑖𝑏 𝑡 = 𝑖𝑏𝑜 𝑡 + ∆𝑖𝑏(𝑡)𝑖𝑐 𝑡 = 𝑖𝑐𝑜 𝑡 + ∆𝑖𝑐(𝑡)
www.eeecube.com
www.eeecube.com
By Neglecting Firing angle errors. For the delta given the waveform of ∆𝑖𝑎 , ∆𝑖𝑏 and ∆𝑖𝑐
www.eeecube.com
www.eeecube.com
Effect of unbalanced voltages
• The presence of the negative sequence component in the AC voltage shifts thezero crossing of the commutation voltages
• With individual phase control (IPC) system. this introduces firing angledissymmetry and results in non-characteristic harmonics.
• With a 5% negative sequence voltage, the third harmonic current generated can beas large as 5% of the fundamental component.
www.eeecube.com
www.eeecube.com
DESIGN OF AC FILTERS
• The major design objective of AC filters is to reduce the telephone interference.
• This can be measured by any of the following performance indices.
Criteria of Design
Harmonic Distortion
This can be measured in two ways:
𝐼𝑛,𝑍𝑛 𝑎𝑛𝑑 𝐸1= Harmonics Current injectedwww.eeecube.com
www.eeecube.com
The second derivation is
In some cases Harmonics distortion can be defined individual for the single harmonic as
www.eeecube.com
www.eeecube.com
TELEPHONE INFLUENCE FACTOR
• This is an index of possible telephone interference and is defined as
Where
𝑝𝑛 is the C message weighting used by Bell
Telephone Systems (BTS) and Edison
Electric Institute (EEI) in USA. The
weighting reflects the frequency depends
sensitivity of the human ear and has a
maximum value 1.0 at the frequency of
1000Hzwww.eeecube.com
www.eeecube.com
Telephone Harmonic Form Factor(THFF)
• This is analogous to TIF except that
• Where 𝑊𝑛 is the psophometric weight at the harmonic order n, as defined as thecumulative commission on telephone and telegraph system(CCITT)
• While TIF is used in USA ,THFF is popular in Europe.
• The maximum values of𝑊𝑛 =1.0 at the frequency of 800Hz.
www.eeecube.com
www.eeecube.com
IT product
• In BTS-EEI system, there is another index called IT product and is defined by
𝐼𝑇 = [
𝑛=1
𝑚
(𝐼𝑛𝐹𝑛)2]1/2
• KIT Product is defined as
𝐾𝐼𝑇 = 𝐼𝑇 100
• Although there are no specific standards in the performance requirements thesuggested values of the above mentioned indices are
www.eeecube.com
www.eeecube.com
TYPES OF FILTER
• The are basically two types of filter used.
• They are
Passive Filter
Damped filters – Low Q Filters Tuned filters – High Q Filters
www.eeecube.com
www.eeecube.com
Active Filter
www.eeecube.com
www.eeecube.com
Resonant frequency
𝜔𝑟 =1
𝐿𝐶
Reactance of the Inductor or capacitor at the resonant frequency
𝑋𝑜 = 𝜔𝑟𝐿 =1
𝜔𝑟𝐶=𝐿
𝐶
• The reactance of the inductor or capacitor at the resonance frequency.
• Note that both filter become identical when R = G = 0. In this case the impedance of the filter is purely reactive becomes zero at ℎ = ℎ𝑟 ,.. where ℎ𝑟. is the order of the harmonic for which the filter is designed.
www.eeecube.com
www.eeecube.com
• We express the sharpness of tuning in terms of the quality factor (Q) defined as,
𝑄 =𝑋0𝑅𝑓𝑜𝑟 𝑡ℎ𝑒 𝑡𝑢𝑛𝑒𝑑 𝑓𝑖𝑙𝑡𝑒𝑟
𝑄 =1
𝐺𝑋0for the Damped filter
Note that G is the conductance of the resistor in parallel with the inductor do the damped resistor
www.eeecube.com
www.eeecube.com
Impedance of single tuned filter
• The impedance (𝑍𝑓ℎ) of the single tuned filter
at the harmonic order ‘h’ is given by
• Where 𝜔 is the fundamental frequency of which can vary with the power system operating conditions.
• A tuned is designed to filter a single harmonics.
• If ℎ𝑟𝜔 = 𝜔𝑟, then obviously
𝑍𝐹ℎ = 𝑅 =𝑋0𝑄𝑎𝑛𝑑 𝑖𝑠 𝑚𝑖𝑛𝑖𝑚𝑢𝑚.
www.eeecube.com
www.eeecube.com
• It is necessary to compute the impedance of the tuned filter as a function of the detuning parameter (del) defined by,
• Considering variations in the frequency (/), inductance (L) and capacitance (C), we can express as
www.eeecube.com
www.eeecube.com
• It is to be noted that ∆𝐿 can be treated as the error in setting the value of L.
• The variation in C can be due to
• error in the initial setting of C and
• the variation in C due to the temperature dependence of the dieiectric constant.
• We can express 𝑍𝑝ℎ,
• The quantity of inside the brackets in the RHS of ,
www.eeecube.com
www.eeecube.com
From the above derived value RHS is equal to 2. Thus, We can finally derive
𝑍𝑝ℎ = 𝑅 + 𝑗𝑋02𝛿
= 𝑋0((𝑖𝑛𝑣)𝑄 + 𝑗2𝛿)
www.eeecube.com
www.eeecube.com
IMPEDANCE OF DAMPED FILTER
• The impedance in a damped filter is not critical, hence we will ignorethe effects variations in the system frequency ,impedance andcapacitance.
• We can express the impedance of the filter as,
www.eeecube.com
www.eeecube.com
• The variation in the (normalized) magnitude of the damped filter𝑍𝑝ℎ
𝑋0
as the function ofℎ𝑖
ℎ0for three different values of the quality factor Q It
is observed impedance remains practically constant at higherfrequencies.
www.eeecube.com
www.eeecube.com
Design of Single tuned filter
• Single tuned filter are designed to filter out characteristics harmonics of single frequency
• The harmonics current in filter are given by
𝐼𝐹ℎ =𝐼ℎ|𝑍𝑠ℎ|
|𝑍𝑠ℎ + 𝑍𝐹ℎ|
• The harmonics voltages are given by
𝑉ℎ = 𝐼𝐹ℎ 𝑍𝐹ℎ =𝐼ℎ
|𝛾𝐹ℎ + 𝛾𝑆ℎ|=𝐼ℎ|𝛾ℎ|
www.eeecube.com
www.eeecube.com
• Basic objective in designing the filter is to select the filter admittance in order to minimize voltage in the harmonics.
• They are two possible representation of system impedance in the complex plane.
• Impedance angle is limited.
• Impedance is limited both in angle and impedance
• The impedance is assumed to lie in the region shown in which R1 and R2 and 𝜃𝑚Obtained in the system characteristics.
www.eeecube.com
www.eeecube.com
𝑄𝑜𝑝𝑡 =cot 𝜃𝑚 2
2𝛿𝑚
=1 + cos 𝜃𝑚2𝛿𝑚 sin 𝜃𝑚
The corresponding Harmonics voltage 𝑉ℎ is
𝑉ℎ =𝐼ℎ
|𝑌𝑓ℎ + 𝑌𝑠ℎ|
=4𝛿𝑚𝑍0𝐼ℎ1 + cos 𝜃𝑚
www.eeecube.com
www.eeecube.com
Minimum Cost Tuned filter
• The cost of the reactor and the capacitor which make up the tunedfilter are dependent on their respective ratings.
• The rating of the capacitor is given by
𝑆𝑐 = (𝑉𝑐12 + 𝑉𝑐ℎ
2)𝜔1𝐶
• The rating of the reactor is given by
𝑆𝐿 = 𝐼𝑓12 + 𝐼𝑓ℎ
2 𝜔1𝐿
Where
𝐼𝑓1 =ℎ
ℎ2 − 1
𝑉1𝑍0; 𝐼𝑓ℎ = 𝑥𝐼ℎ
𝑉𝑐1 =ℎ2
ℎ2−1𝑉1 ; 𝑉𝑐ℎ = 𝑥𝐼ℎ𝑍0
www.eeecube.com
www.eeecube.com
• The reactive power generated by the filter branch at the frequency is
𝑄𝑓 = 𝑉1𝐼𝑓1 =ℎ
ℎ2 − 1
𝑉12
𝑍0Eliminating 𝑍0 in the above equation and sub in the 𝑆𝑐 , 𝑆𝐿 equation we get
The cost of filter is
𝐾 = 𝐴𝑄𝑓 + 𝐵1
𝑄𝑓
Where A and B are the Constants.
When cost of filter is minimum ,so reactive power supply by the filter is at an optimum value
𝑄𝑓∗ =
𝐵
𝐴www.eeecube.com
www.eeecube.com
Design of High Pass Filter
• For Harmonics frequencies of order equal to or higher than 17, acommon second order high pass filter is usually provided.
• By defining the following parameters
ℎ0𝜔1 = 1 𝐿𝐶
𝑍0 = 𝐿/𝐶
𝜎 = 𝑅 𝑍0
www.eeecube.com
www.eeecube.com
• The following values can be chosen
0.5 < < 2
ℎ0 ≤ 2ℎ𝑚𝑖𝑛Where ℎ𝑚𝑖𝑛 is the smallest value of h to be handled by the filter.
The filter impedance is given by
𝑍𝑓 =𝑍0[𝜎 + 𝑗 ℎ0 ℎ . (𝜎
2 − 1 −𝜎ℎ0ℎ
2
]
1 + (𝜎ℎ0ℎ)2
The reactive power supplied by the filter is
𝑄𝑓 =ℎ0
ℎ02−1. (𝑉12
𝑍0)
If Filtering is improved If Q1
increase So choose ℎ0 is high Its
advantage then six pulse
www.eeecube.com
www.eeecube.com
Protection of Filters
• The filter is exposed to an overvoltage during switching in and the magnitude.
• The overvoltage is a function of the short circuit ratio (higher with low values of SCR) and the saturation characteristics of the converter transformer.
• During switching in, the filter current (at filter frequencies) can have magnitudes ranging from 20 to 100 times the harmonic current in normal (steady-state) operation.
• The lower values are for tuned filters and higher values are applicable to high pass fillers.
www.eeecube.com
www.eeecube.com
• These overcurrent must be taken into consideration in the mechanical design of reactor coils.
• When filters are disconnected, their capacitor remain charged to the voltage at the instant of switching.
• If the network frequency deviates from the nominal value, higher currents and losses will result in AC filters. li they exceed the limits, the filters have to be disconnected.
www.eeecube.com
www.eeecube.com
DC FILTERS • The harmonics in the DC voltage across the converter contain both characteristic and
non-characteristic orders.
• These harmonics result in current harmonies in DC lines and cause noise in telephone circuits.
• The harmonic current generated in the line can be computed from the knowledge of harmonic voltage sources at the converters, smoothing reactor, DC filter and line parameters.
• The effectiveness of the DC filter is judged by one of the following criteria:
1. Maximum voltage TIF on DC high voltage bus
2. Maximum induced noise voltage (INV) in milli voltsfkm in a parallel test line one kilometer away from the HVDC line
3. Maximum permissible noise to ground in telephone lines close to HVDC lines.
www.eeecube.com
www.eeecube.com
• The second criterion is widely used and involvesthe computation of harmonic currents and themutual impedance which depends upon factorssuch as
• Earth resistivity
• Mono polar or bipolar operation
• Grounder metallic returns.
• Typically INV of 18-20 m\/[km for mono polaroperation is allowed.
• The DC filters are also of single or double tunedtype to filter out 6th and 12th harmonics and a highpass filter for higher order harmonics.
• Computer Programmers are generally used inevaluating the performance of filters anddimensioning them.
www.eeecube.com
www.eeecube.com
CARRIER FREQUENCY AND RI NOISE
www.eeecube.com
www.eeecube.com
CARRIER FREQUENCY AND RI NOISE
• HVDC converter stations can produce high levels of electrical noise in the Carrier frequency band from 20 KHz to 490 KHZ.
• They also generate radio interference noise in the mega Hertz range of frequencies.
• However, converters are usually located in buildings which are effectively shielded against electromagnetic radiation.
• PLC- RI filter can be reduced and minimized the impact of noise and elimination of interference with power line carrier communication
• The attenuation requirements of the filters must above the curve shown below
www.eeecube.com
www.eeecube.com