harris rf350 k

Harris RF350-K

Military Surplus at its finest!

I'll probably live to regret it but I sold this Harris rig in 2010.

Oooh, I can already feel a disturbance in the force...

This system consists of the Harris RF350K 100 watt transceiver and the Harris RF355 500 watt LinearPower Amplifier. Both units are in shock mount transit cases. Additionally, there is the somewhat rareRF352 Harris Remote Control Unit. This unit allows complete control of the system from a remotelocation. Of course, the exceedingly rare Harris remote control interface board that mounts in the RF350Kis included and in place. The RF352 remote control unit is mounted in a high quality metal case with feetfor table top use.

W7KF - Harris RF350-K http://www.w7kf.com/Articles/Rigs/HarrisRF350K.html

1 de 21 14/07/2012 11:18 p.m.

Included is an 800 foot cable that runs between the RF352 Remote Control Unit and the RF350K / RF355LPA. Yes, 800 feet! This cable will allow you to put the rig out in the barn, garage or down in thebasement and control it from 800 feet away. This makes for a wonderfully quiet system. There are no fansor blowers in the Remote Control Unit – it's dead silent.

Included in the sale is a set of printed manuals. Each manual is either a Harris original or a high qualityreprint, complete with extended page fold-out schematics. Also, the impossible to find Harris Operator'sCard and System Fault Card is included.

And, finally, I'm including a new set of updated EEPROM chips and a spare set of band pass filter relays.(Apparently, these relays are a common cause of failure. I haven't seen that failure but picked up thespares – just in case.) Oh, of course, a military M-80 hand mic that works with the RF350K.

All you need to add is an antenna and you're on the air with this legendary Harris "Pacer Bounce" setup.

BTW, are you a CW loving green radio guy? This system is the best CW rig of all the green radios I haveused. In the CW mode a narrow filter kicks in – it's either 400 Hz or 500 Hz. Also, I've tuned the T/Rdelay for optimum CW use. It's not QSK but the T/R turn-around time is the best I've encountered in aMIL rig. It also has a variable BFO so you can set the receive CW tone to whatever you like – unlike mostmilitary CW modes where you're stuck listening to 1,000 Hz.


2 de 21 14/07/2012 11:18 p.m.

Naturally, the RF350K system works great on PACTOR and other digital modes as well. It also includesfull phone patch capability, etc. And, although I've never attempted it, the documents describe setting upthe remote control capability over standard phone lines. You should be able to put the rig up on amountaintop and control it from your armchair at home!

BTW, at present I have both the RF350K and the RF355 LPA set up to operate on 240 VAC. The RF352Remote Control Unit is set up to operate on 120 VAC. If you want to operate the RF350K and RF355LPA on 120 VAC you will have to change the plug on the end of the two power cables and flip a switchinside each of the two units. This is all documented in the included manuals.

This setup cost Uncle Sam about a kazillion dollars. Finding a complete setup like this today is prettychallenging. And, then you have to find all the MIL connectors and build up cables and all that. Ugh.

The rig is at my QTH in Montana. You are welcome to drop by and give it a test drive!

But, enough of this talk -- here are the pics and more details:

Here's an overview of the whole system. That's the RF352 Remote Control Unit in the desk top case, theRF355 500 watt LPA in the gray transit case and the RF350K in the blue transit case. On top of theremote control are the spare relays and the updated EEPROMs. On the floor is the 800 foot remotecontrol cable and the stack of manuals. The front and rear covers for the transit cases are on the right.


3 de 21 14/07/2012 11:18 p.m.

Here is the Remote Control Unit. The M-80 Mic is NOS and has just been unpacked.


4 de 21 14/07/2012 11:18 p.m.

Another view of the RF-352 Remote Control Unit, on 20 meters.


5 de 21 14/07/2012 11:18 p.m.

Here's a close-up of the remote control while I'm whistling up a nice sine wave tone. The RF355 LPA is onand the meter is indicating 500 watts output.

Here's the other side of the remote control unit. The interface between the RF355 Remote Control and theRF350K is using the RS-422 protocol and that's what the 800 foot cable is wired for. I couldn't get theRS232 interface to work so I set it up for RS-422 which works great.


6 de 21 14/07/2012 11:18 p.m.

The remote control unit is mounted in a Schroff case. It's a nice quality case; it does have some shallowscratches but no dents. A paint job would make it outstanding. The case is easy to disassemble and paint. Iuse these cases for everything around here and I like them a lot.

Here's the 500 watt LPA in operation. Again, I'm providing a perfect sine wave by whistling into the mic.The meter is on the power out scale and is showing a bit over 500 watts out.


7 de 21 14/07/2012 11:18 p.m.

Here's another view of the 500 watt LPA in operation. The meter is in the plate voltage position andshowing a bit over 2300 volts – this is in the key up condition. When producing the rated output the platevoltage is 2000 volts.


8 de 21 14/07/2012 11:18 p.m.

Here's a pic of the RF350K. The transceiver and the 500 watt LPA are mounted on rack shelves andinstalled in the shock mounts in the transit cases. The rack shelves are full depth so the units arecompletely supported. If you'd rather put the units in regular racks you'll need the included rack shelves.They're all steel construction and built to hold the weight of these units.


9 de 21 14/07/2012 11:18 p.m.

Here's a pic of the RF382 automatic 500 watt antenna coupler. This is about the most amazing antennacoupler you'll ever find. It will match the RF350K system to just about anything from 9' long and up. Itwill do so automatically. It will remember the tuning settings and will re-establish tune in approximately0.2 seconds on a frequency that it has been on before. This thing ROCKS!


10 de 21 14/07/2012 11:18 p.m.

Included in the sale but not shown here is a 100 foot control cable that runs between the RF-350K and theRF-382 coupler. Also, a 100 foot length of LMR-400 low loss coax cable to connect the RF-350K and theRF-382 coupler. You need both. So, add a chunk of wire and you're on the air!

Shown below is the 800 foot remote control cable. Now, the 800' figure is approximate. It was a 1000 footroll of cable and I've cut off a piece or two to make various jumpers. It might be closer to 900 feet. Ormaybe 700 feet. I don't know and I'm not going to stretch it out to measure it. It's long, it has the properconnectors on it and it works great with this system.

The manual for the RF350K transceiver. 'Nuff said..


11 de 21 14/07/2012 11:18 p.m.

The BIG schematic pages are proper fold-outs


12 de 21 14/07/2012 11:18 p.m.

The RF-350K Operator's Card and the System Fault Card.


13 de 21 14/07/2012 11:18 p.m.

The manual for the RF355 500 watt Linear Power Amplifier (LPA).



14 de 21 14/07/2012 11:18 p.m.

The manual for the RF352 Remote Control Unit.


15 de 21 14/07/2012 11:18 p.m.



16 de 21 14/07/2012 11:18 p.m.

Spare band pass filter relays. There is also a mod that puts a tiny amount of DC through the relay contactsin the RF350K. Apparently that keeps the relays from developing issues. I'll include the documentation ofthat mod with the RF350K manual. Anyway, the relays in this rig haven't failed. I just picked up the spareswhen I had a chance to do so..


17 de 21 14/07/2012 11:18 p.m.

Here's the new, updated EEPROM chips for the RF350K. I never got around to installing them. These areavailable from KO6NO


18 de 21 14/07/2012 11:18 p.m.

This pic was taken during the BITE self test as initiated from the Remote Control Unit. During the test, theentire display is enabled so you can look for missing characters while the system checks itself out.


19 de 21 14/07/2012 11:18 p.m.

This picture shows the result of the full system BITE self test: “PASSED”.


20 de 21 14/07/2012 11:18 p.m.

The system works great and I use it when I'm the net control station on my MARS nets. If you'd like tohear the rig in action send me an email and we'll set up a sked. I can operate on any frequency that's legalfor both of us.

The bottom line?! Well, as you can see, I've got a lot wrapped up in this system. The transit cases alonecost over $500. The 1000' feet of remote control cable? You don't even want to know. But, I've got toomany rigs and I need to thin the herd..

I've been tracking prices on ebay:

Unit Low Average HighRF350K Transceiver $384 $934 $2133RF355 Linear Power Amplifier $384 $580 $950RF352 Remote Control Unit $148 $260 $664RF382 500 Watt Antenna Coupler $275 $800 $1800Totals: $1191 $2574 $5547

So, the average price of the three units plus the auto-coupler would be: $2,574. But, that is for unknownebay units likely without cables, documentation, transit cases, etc. This is a complete, working, turn-keysystem with all cables, connectors, etc. Connect some wire for an antenna and you're on the air!

But, wait, there's more! You also get:

Nearly complete set of printed high quality reproduction or original manuals (sorry no manual forthe RF382 coupler).

Shock mount transit cases with steel rack shelves

All metal desktop rack case for the remote control unit

All interconnect and power cables and M-80 mic

800 ~ 900 foot remote control cable

New EEPROM chip set

New band pass filter relay spares

Sorry, this rig has been SOLD!

It was a great rig! But, I sold it in 2010..

Home - Rigs - Top


21 de 21 14/07/2012 11:18 p.m.

harris rf350 k

Documents