harris ridge condos panel submittal rev a

SMITHPUMPCOMPANY,INC, LarryWingo/JosephScott172221HarrisRidgeCondominiumsRevision:Original July27,2015

SUBMITTAL DOCUMENTS REVISION A

for

Harris Ridge Condominiums

on the

Control Panel for the Submersible Non-Clog Sewage Pumps

CONTRACTOR:

C.C. Carlton Industries, Ltd

ENGINEER: Hanrahan, Pritchard Engineering, Inc.

SPECIFICATIONS:

Section 11306: Submersible Non-clog Pump

Smith Pump Company Project Number: 172221

For questions please contact Smith Pump Company, Inc. 301 M&B Industrial Waco, Texas 76712 Attention: Larry Wingo / Joseph Scott Phone: 254.776-0377 Facsimile: 254-776-0023 E-mail: [email protected] Website: www.smithpump.com Note to Contractor:

The proposed equipment will not be available or purchased from our vendors until written approval of the Submittal is provided. Smith Pump Company will provide the equipment, as approved, and may not be identical to the Engineers specifications. Please review carefully. It is the Contractors responsibility to verify field conditions including voltage, elevations, etc. Changes after approval may result in additional charges for modifications, field service, restocking, or other services.


Table of Contents Harris Ridge Condominiums Contractor: C.C. Carlton Industries, Ltd Project: Submersible Non-clog Pump SPCO Project Number: 172221 Section 11306 Control Panel for Submersible Non-Clog Pump ITEM ---------------- DESCRIPTION -------------------- 1 Cover Page 2 Table of Contents 3 TAB: General Information Control Panel Data Sheet Revised Comments and Clarifications Original Comments and Clarifications Layout Drawings Control Panel Exterior Layout Control Panel Interior Layout Schematics Control Panel - 480V Power Control Panel - Starters Control Panel - Control Logic Control Panel - Crystal Ball Control Panel - Annunciator Control Panel - Terminal Block ID Bill of Materials Sheet 1 Sheet 2 4 TAB: Cut Sheets


TAB: GENERAL INFORMATION

SMITH PUMP COMPANY, INC.

301 M&B Industrial (800) 299-8909 (254) 776-0377

Waco, Texas 76712 FAX (254) 776-0023

Page 1 of 2

Duplex Control Panel Operation Summary Sheet

Panel No. 6002-334 August 17, 2015 Project No. 172221-02 Project: Harris Ridge Condos Pump Voltage: 460 VAC Phase: 3 Hz: 60 H.P. Pump 1: 7.5 FLA: 10.8 H.P. Pump 2: 7.5 FLA: 10.8

DESCRIPTION: NEMA 12 Painted Steel Enclosure (60 x 60 x 24) - 3 Point Latching Mechanism on Overlapping Exterior Doors - 12 Leg Kits - Door Stops - Operator Controls on Exterior Door Power Distribution Blocks Ground Bus Bar with Insulating Barrier Separate control circuit from motor power circuits Fused Solid State Power Monitoring Unit Molded Case Main Circuit Breaker with Auxiliary Shunt for RTU Interface Molded Case Motor Circuit Protectors for Pump Motors Molded Case Odor Control Circuit Breaker Molded Case Control Circuit Breaker for External 2KVA Transformer (Shipped Loose) 20 Amp Duplex GFCI Outlets (located on the Back Plate & Exterior Door) 250VA Control Transformers (One per Motor Starter) NEMA 2 Motor Contactors with Solid State Electronic Overload Relays Solid State Overload Relay Displays on Exterior Door NEMA 4X Overload Reset Pushbuttons on Exterior Door Analog Phone Modem with Surge Protective Device for RTU (Modicon PLC) Output to

Walnut Creek WWTP 850VA Un-Interruptible Power Supply For Control Circuit Modicon PLC with CPU module, rack extension module, 4 ch analog input module, 8 ch

digital output module, 16 ch digital input module Devar Pump Controller (On Exterior Door) with Operation by Submersible Transducer & Two

(2) Normally Open Floats (Low & High Level) Dual Channel Pump Protection Relays

Monitors Motor High Winding Temperatures & Moisture within Pump Seal Chamber Adjustable On-Delay Timers for Pump Start Delay 11 Pin Control Relays (As Needed) Fluorescent Interior Work Lights with Manual Off/ On Switch Elapsed Timer Meters 7 Digits, Non-Resettable 3 Position HAND-OFF-AUTOMATIC Rotary Switches 30mm, NEMA 4X, Maintained 2 Position HORN ENABLE-DISABLE Rotary Switch 30mm, NEMA 4X, Maintained Red PUMP RUN LED Indicator Lights 30mm, NEMA 4X, Push-To-Test

SMITH PUMP COMPANY, INC.

301 M&B Industrial (800) 299-8909 (254) 776-0377

Waco, Texas 76712 FAX (254) 776-0023

Page 2 of 2

Duplex Control Panel Operation Summary Sheet

Panel No. 6002-334 August 17, 2015 Project No. 172221-02 Project: Harris Ridge Condos Pump Voltage: 460 VAC Phase: 3 Hz: 60 H.P. Pump 1: 7.5 FLA: 10.8 H.P. Pump 2: 7.5 FLA: 10.8

DESCRIPTION: Green PUMP STOP LED Indicator Lights 30mm, NEMA 4X, Push-To-Test Black PUMP FAILURE Pushbuttons 30mm, NEMA 4X, Momentary 12 Channel Annunciator Unit with Soft Pushbuttons for Various Alarms & Resets Terminals for Field Connections Exclusions: Smith Pump will not be responsible for: Programming of RTU/PLC; programming to be performed by others. Bubbler System w/ corresponding components


Comments and Clarifications

Harris Ridge Condominiums Contractor: C.C. Carlton Industries, Ltd Project: Submersible Non-clog Pump

SPCO Project Number: 172221

Revised Submittal Comments 1. We are not including generators, generator receptacles, bubbler system & components

relating to the bubbler system, SCADA, instrumentation, conduit, PFCC, MCC, power drop, special tools, or tool chest. Unloading and installation is by others.

2. Smith Pump does not provide breaker panel LP or the transformer powering it. Remote horn and alarm beacon are not provided.

3. PLC wiring shall be 18 AWG SIS wire, not 14 AWG. PLC manual states 15 AWG wire maximum on screw terminals.

4. Annunciator lights are red, not amber. Amber lights are not available in current models.

5. In lieu of heat shrink tubing, Brady nylon cloth wire markers shall be utilized for wire identification.

6. Terminal block group numbers are assigned based upon function (i.e. Crystal Ball, PLC

Operation, Pump Motor, etc.)

7. The wire color code has been modified from the specifications to eliminate repetitive colors for different voltages:

AC Hot / Controls Red AC Neutral Controls White Annunciator Contacts Yellow DC+ Controls Blue w/ Red Tracer DC- Controls Blue w/ White Tracer PLC/RTU Contacts Purple (18 AWG into PLC connector terminals)

8. Smith Pump has concerns with specified method of wiring UPS hot swap relays.

If CR-UPS closes before CR-UPS1 opens, fuses can blow when UPS voltage is higher or lower than line voltage. This can be avoided with an on-delay timer located in front of CR-UPS2. While Smith Pump is making this recommendation, the control panel is being constructed per the design of the electrical engineer of the project.

9. Contractor to verify the following information: a. Voltage and Wye/Delta configuration b. Elevations shown on drawings.

10. Warranty: Warranty will be for 12 months after acceptance, but not to exceed 18

months after delivery.


Original Submittal Comments

1. We are not including generators, generator receptacles, SCADA, instrumentation,

conduit, PFCC, MCC, power drop, special tools, or tool chest. Unloading and installation is by others.

2. Smith Pump does not provide breaker panel LP or the transformer powering it. Remote horn and alarm beacon are not provided.

3. Proposed bubbler deviates from specification. Bubbler systems includes: a. Dual air compressors b. Air tank c. Automatic purge based on air flow restriction d. RS-232 serial port for SCADA system / Modbus communication e. 4-20ma output signal representing liquid depth f. Fault signals g. See data sheets for additional information

4. Contractor to verify the following information:

a. Voltage and Wye/Delta configuration b. Elevations shown on drawings.

5. Warranty: Warranty will be for 12 months after acceptance, but not to exceed 18 months

after delivery.

120 VACLP-1

120 VAC LP-2

120 VACLP-2 / UPS

120 VACLP-2 / UPS

120 VACLP-2

24 VDC

Rack 1 Slot 3 Rack 1 Slot 2 Rack 1 Slot 1

Rack 1 Slot 4

120 VACLP-5

CONTROL PANEL INTERIOR LIGHTING

COMPANYSMITH

CONTRACTOR

DATEDWG. NO.

ENGINEER

SCALE

OWNER

PROJECT

PRODUCT

CKBY REV

PUMP

-- --/--/-- --- ---

PROJECT

CONTROLS

HARRIS RIDGE CONDOS

HARRIS RIDGE CONDOS

C.C. CARLTON

JSRA ENGINEERS

172221-02

T:\CAD\CONTROL\SCHEMATIC\6002-334

8/14/15 NA LSW JDS ---SHEET 3 OF 6

Control Panel Pricing Flowserve 3MSX8A October 28, 20146002-334 quote: 6000-0668 ref: 6002-249 10.8 FLA J. McHattieDuplex, 460V, 3P, 7.5 Hp each Transducer & Bubbler Harris Ridge CondominumsNEMA 12 Enclosure Project: 172221-02-01

BOM 1 of 2

HARRIS RIDGE CONDOMINUMS PROJECT #: 172221-02 CONTRACTOR: C.C CARLTON MODEL NO: 6002-334 DUPLEX NEMA 12 PAINTED STEEL CONTROL PANEL

ITEM QTY DESCRIPTION MANUFACTURER PART NO.35 1 NEMA 12 Painted Steel Enclosure: 60" x 60" x 24", 3PT, Door Stops, 12" LegsHoffman A606024LP-MOD36 1 Painted Steel Panel Plate: 60" x 60" Hoffman A60P6053 1 Insulated Barrier: Bolt-On, 60" x 6" Hoffman F88BK6057 2 Quarter-Turn Non-Locking Wing Handle EXM 880 SCQ4-WNH37 1 UPS, 850VA, 510 Watts, 120 Volt, Din Rail Mount Sola SDU-85058 1 Ground Bar with 20 pre-drilled connection points Square D PK18GTA48 1 Two Wire Temperature Transmitter for 2 or 3 Wire RTDs, 0-200 F Devar SM812EC-001221 1 Pump Controller, 120VAC, 4-20ma Input, 4 SPDT Devar 3020-4-42059 1 Submersible Transducer, 4-20mA, 15 PSI, 60 Ft Cable, Intrinsically Safe Dwyer PBLTX-15-6056 1 3 Pole Power Distribution Block, 175 Amp, 600 Volt, Phenolic Marathon 142357050 4 1 Pole Power Splice Block, 115 Amp, 600 Volt, Thermoplastic Marathon 141130049 1 1 Pole Power Distribution Block, 115 Amp, 600 Volt Thermoplastic Marathon 141140060 4 3 Pole Power Splice Block, 90 Amp, 600 Volt, Thermoplastic Bussmann NDN111-WH11 1 3 Pole Circuit Breaker: 60 Amp, 600VAC, 25K AIC Square D HGL3606061 1 Circuit Breaker Auxillary Contact Field Installable Square D S2945038 2 Motor Circuit Protector, 30 Amp, 1.5-25 Amp Full Load Range Square D HJL36030M7142 1 2 Pole Circuit Breaker: 15 Amps, 480 Volt, 18/25K AIC Square D FAL2401552 1 3 Pole Circuit Breaker: 30 Amps, 480 Volt, 18/25K AIC Square D FAL3403055 1 Three Pole Fuse Block, Class CC, 600V, Isolating, Non-indicating Allen Bradley 1492-FB3C3062 3 1 Amp Class CC Fuse, 600 Volt, Time Delay, Rejection Type Mersen ATQR123 3 Current Transformer, 200:5 ratio Simpson 370222 1 PM800 Power Monitor: Base Meter Unit with integrated display Square D PM820MG2 1 PM800 Module, 2 digital outputs (relays), 6 digital inputs Square D 3020-PM8M26

46 1 Single White Receptacle, 20 Amp, 120 Volt Leviton T5020-W46 1 Stainless Steel Cover: Single Receptacle Leviton 84004-4012 1 DC Power Supply: [email protected], DIN Rail Sola SDN2.5-24-100P25 1 24VDC Power Supply Module: 1.04 Amps, 36 Watts Modicon BMX CPS 350028 1 CPU Module: Ethernet/ USB/ Modbus Serial Port, 256 Inputs/ Outputs, 24VDCModicon BMX P34 202026 2 Analog Input Module, 16 Channels, 120VAC Modicon BMX DAI 160427 1 Analog Output Module, 8 Channel, 120VAC Modicon BMX DRA 080524 1 Analog Input Module: 4 Channel, 4-20 mA Inputs Modicon BMX AMI 041029 1 Rack Extenstion Module, 8 Slots Modicon BMX XBP 080030 5 Protective Covers for Rack Extenstion Module Modicon BMX XEM 01031 1 Protection Bar for Rack Extension Module Modicon BMX XSP 080019 1 Dual Line RJ11 Jacks Surge Protector L-Com HGLN-D2T32 1 Analog Phone Modem: Serial RS232 w/ DB9 Connector, RJ-11 Modular Jack Telenetics MIU14.446 1 Weatherproof Gray Gang Box - Duplex Red Dot IH3-11 2 RJ11 Stainless Steel Cover Plates Various 43080-1S11 2 RJ11 Connectors Various 41108-RW3

14 3 End Barrier for Terminal Block, White Allen Bradley 1492-N3613 160 Terminal Block, 600 Volt, 30 Amp, #30-#12 AWG, White Allen Bradley 1492-HM173 4 Side Jumper, 10 Pole Allen Bradley 1492-SJ6-1015 6 End Anchor for Terminal Block Allen Bradley 1492-N4717 2 End Barrier for Isolating Fuse Block Allen Bradley 1492-N3716 21 Fuse Block, 300V, 1/4-1-1/4" Fuse, Isolating, Non-indicating Allen Bradley 1492-H663 3 0.125 Amp Fuse, 250 Volt Goulds GGC-1/864 3 0.5 Amp Fuse, 250 Volt Goulds GGC-1/265 9 2 Amp Fuse, 250 Volt Goulds GGC-266 2 3 Amp Fuse, 250 Volt Goulds GGC-367 1 7 Amp Fuse, 250 Volt Goulds GGC-733 2 Dual Channel Pump Protection Relay: HMWT & Seal Failure Multi-Tech MOS-1P68 2 14 Pin Rectangular Base Multi-Tech PB12P39 2 NEMA 2 Contactor, 45 Amps, 120 Volt Square D 8502SDO2V02S6 2 3 Phase Electronic Overload Relay Symcom 777-P2

7.5 HP, 480 Volt , 3 Phase

BILL OF MATERIAL

BOM 2 of 2

HARRIS RIDGE CONDOMINUMS PROJECT #: 172221-02 CONTRACTOR: C.C CARLTON MODEL NO: 6002-334 DUPLEX NEMA 12 PAINTED STEEL CONTROL PANEL

ITEM QTY DESCRIPTION MANUFACTURER PART NO.40 2 Communication Module for 777 Remote Display Symcom RS485-MS-2W40 2 Local Display/ Controller for 777 Overload Relay Symcom RM100018 2 Two Pole Fuse Block, Class CC, 600V, Isolating, Non-indicating Allen Bradley 1492-FB2C3069 4 1 Amp Class CC Fuse, 600 Volt, Time Delay, Rejection Type Mersen ATQR143 2 250VA Control Transformer: 240/480 Volts IN, 110 Volts OUT Hammond SP250MQMJ45 1 Stainless Steel Cover: Duplex GFCI Receptacle Crouse-Hinds HUWIS2645 1 Weatherproof Gray Outlet Box: Duplex GFCI Receptacle Red Dot IH3-145 1 Duplex GFCI Ivory Receptacle, 20 Amp, 120 Volt Leviton 7899-I34 1 Annunciator: 12 LED Red Lights, 4 NO Pushbuttons Ametek AN-3196B-F3A-B-X-NR-AR-PM-NR-Y7 2 30mm Maintained 3 Position Selector Switch, 2 NO & 2 NC Square D 9001SKS43BH28 8 NEMA 4X 30mm Pushbutton, NO & NC Contact Square D 9001SKR1BH139 2 Red Push-To-Test LED Light: 30mm, NEMA 4X, 120VAC Square D 9001SKT38LRR3154 1 30mm Maintained 2 Position Selector Switch Square D 9001SKS11B20 2 External Elapsed Time Meter, 110 Volt, Non-resettable, 7 figure Display Redington 711-0160-G3 2 Multi-Function Timer, 5 timing ranges, DPDT, 120V, 11 pin Square D 9050JCK70V205 2 11 Pin Socket: 300 Volt, 10 Amp, 3PDT Idec Corporation SR3P-0522 2 120 Volt Fluorescent Light Enclosure - 18" Hoffman LF120V1844 2 PANELITE Remote Door Switches Hoffman ALFSWD22 2 120 Volt Flurorescent Light Bulb Sylanvia F18T8TW/K244 30 Control Relay, 5 Amp, 120VAC, 3PDT, LED Indicator Square D 8501-KP1370 6 Circuit Protection Varistor: 130VAC, 170VDC; 340V; 10A; Metal Oxide; 180pF Little Fuse V07E130P71 30 11 Pin Socket: 300 Volt, 10 Amp, 3PDT Idec SR3P-0572 125" Corrosion Inhibitor Strip Hoffman AHC160R10 2 Green Push-To-Test LED Light: 30mm, NEMA 4X, 120VAC Square D 9001SKT38LGG31

21 1 Pump Controller, 120VAC, 4-20ma Input, 4 SPDT Devar 3020-4-4202 1 PM800 Power Monitor: Base Meter Unit with integrated display Square D PM820MG33 1 Dual Channel Pump Protection Relay: HMWT & Seal Failure Multi-Tech MOS-1P39 1 NEMA 2 Contactor, 45 Amps, 120 Volt Square D 8502SDO2V02S6 1 3 Phase Electronic Overload Relay Symcom 777-P29 1 Red Push-To-Test LED Light: 30mm, NEMA 4X, 120VAC Square D 9001SKT38LRR313 3 Multi-Function Timer, 5 timing ranges, DPDT, 120V, 11 pin Square D 9050JCK70V204 5 Control Relay, 5 Amp, 120VAC, 3PDT, LED Indicator Square D 8501-KP1310 2 Green Push-To-Test LED Light: 30mm, NEMA 4X, 120VAC Square D 9001SKT38LGG31

SPARE PARTS

7.5 HP, 480 Volt , 3 Phase

BILL OF MATERIAL

SMITHPUMPCOMPANY,INC, LarryWingo/JosephScott172221HarrisRidgeCondominiums Revision:Original July27,2015

TAB: CUT SHEETS

Bulletin 1492

IEC Terminal Block Accessories

12-91

Marking Systems

0

1

2

3

4

5

6

7

8

9

10

11

12

13

Blank Markers

Photo For Use WithMarkersper Card Marker Size

PkgQty. Cat. No.

Snap-In Individual Markers1492-M 1492-L 100 3 x 5 mm 5 1492-M3X5

1492-L 120 3 x 12 mm 5 1492-M3X12

1492-J, L

200 5 x 5 mm 5 1492-M5X5

144 5 x 8 mm 5 1492-M5X8

144 5 x 10 mm 5 1492-M5X10

144 5 x 12 mm 5 1492-M5X12

96 5 x 15 mm 5 1492-M5X15

20 5 x 30 mm 5 1492-M5X30

1492-J, L200 6 x 5 mm 5 1492-M6X5

120 6 x 10 mm 5 1492-M6X10

1492-J, L, 1738 ArmorPoint 120 6 x 12 mm 5 1492-M6X12

1492-J, L108 7 x 12 mm 5 1492-M7X12

160 8 x 5 mm 5 1492-M8X5

NEMA (1492-HM1, -HM2, -HM3) Terminal Blocks,1492-CB Circuit Breakers 120 6 x 10 mm 5 1492-MN81

NEMA (1492-HM3) Terminal Blocks, 1492-CB CircuitBreakers 40 10 x 10 mm 5 1492-MN83

1492-W,R, 700-HA Relays56 8 x 9 mm 5 1492-MS8X9

56 8 x 12 mm 5 1492-MS8X12

700-HN204, -HN205, Relay Sockets 40 8 x 17 mm 5 1492-MS8X17

1667 PanelConnect 40 9 x 20 mm 5 1492-MS9X20

100-C, -D Contactors, 700-CF Relays, 140 CircuitBreakers, 193-E1, -E3 40 10 x 17 mm 5 1492-MS10X17

Snap-In Linked Markers1492-MR

1492-J, -L

120 5 x 8 mm 5 1492-MR5X8

120 6 x 8 mm 5 1492-MR6X8

120 5 x 12 mm 5 1492-MR5X12

120 6 x 12 mm 5 1492-MR6X12

84 8 x 12 mm 5 1492-MR8X12

1492-WM3, -WMD1 80 5 x 5 mm 5 1492-MS5X5

1492-W, 700-HA, 800F Contact Block 80 5 x 9 mm 5 1492-MS5X9

1492-W, 700-H Relays 80 5 x 12 mm 5 1492-MS5X12

1492-W, -R, 700-H Relays 80 6 x 9 mm 5 1492-MS6X9

1492-W, 700-H Relays 80 6 x 12 mm 5 1492-MS6X12

Snap-In Hinged Markers

1492-L

96 5 x 10 mm 5 1492-MH5X10

96 5 x 15 mm 5 1492-MH5X15

80 6 x 12 mm 5 1492-MH6X12

Cable Markers1492-MW External Diameter (mm)

Markersper Card Marker Size

Pkg.Qty. Cat. No.

from 0.276 in. (from 7.0 mm) 32 9 x 24 mm 5 1492-MW9X24




0.1620.193 in. (414.9 mm) 32 5 x 21 mm 5 1492-MW5-21

0.1850.229 (0.268) in. (4.75.8 [6.8] mm) 32 6 x 21 mm 5 1492-MW6-21

0.2290.276 (0.335) in. (5.87.0 [8.5] mm) 32 7 x 21 mm 5 1492-MW7-21

Requires cable ties.Requires Cat. No. 1492-GMC Requires Cat. No. 1492-PLOTPLTA

www.ab.com/catalogs Preferred availability cat. nos. are bbold.

Publication A117-CA001A-EN-P

jeffmRectangle

Bulletin 1492

NEMA Terminal Block Accessories

12-111www.ab.com/catalogs Preferred availability cat. nos. are bbold.


0

1

2

3

4

5

6

7

8

9

10

11

12

13 The 1492-SJS Insulating Sleeve reduces exposure to live parts on the 1492-N39 and 1492-N49. The 1492-SJS used with the 1492-N39 and 1492-H1 or 1492-

HM1 provides IEC 947 IP2X finger protection.

1492-EAHJ35

1492-N2

.013 (3.2 mm)

1492-N23

0.56(14.3 mm)

1.44 (36.5 mm)

1.25

(31

.8 m

m)

1492-N47

0.34(8.6 mm)

1.50 (38.1 mm)

1.70

(43

.2 m

m)

End Anchors

Cat. No. A B C D E

1492-15A 1.5 in.(38.1 mm)1.03 in.

(26.2 mm)0.594 in.

(15.1 mm)0.234 in.(5.9 mm)

0.75 in.(19.1 mm)

1492-15E 1.5 in.(38.1 mm)1.03 in.

(26.2 mm)0.594 in.

(15.1 mm)0.234 in.(5.9 mm)

1492-25A 1.88 in.(47.8 mm)1.19 in.

(30.2 mm)0.688 in.

(17.5 mm)0.203 in.(5.2 mm)

0.97 in.(24.6 mm)

1492-25E 1.88 in.(47.8 mm)1.19 in.

(30.2 mm)0.688 in.

(17.5 mm)0.234 in.(5.9 mm)

1492-15A, 1492-25A 1492-15E, 1492-25E

A = WidthB = Height

A

D C

E

A = WidthB = Height

DC

Bulletin 1492




Specifications

0

1

2

3

4

5

6

7

8

9

10

11

12

13

Multiple Wire Connection Combination for Stranded Copper Conductors of the Same Gross Section for Allen-BradleyTerminal Blocks

Terminal Blocks

Cat. No.

Wire Size AWG (mm2)

#22 #20 (0.5) #18 (0.75) #16 (1.5) #14 (2.5) #12 (4)

Number of the Same-Size Wires Per Terminal1492-H4, -H5, -H6, -H7 4 4 3 2 2 1

Fingersafe Terminal Blocks

Cat. No.

Fingersafe Terminal Blocks

#22 #20 (0.5) #18 (0.75) #16 (1.5) #14 (2.5) #12 (4) #10 (6) #8 (10)

Number of the Same-Size Wires Per Terminal

1492-HM1 4 4 3 2 2 1

1492-HM2 4 4 3 2 2 1

1492-HC6 4 4 3 2 2 1

1492-HM3 4 4 4 3 2 2 1 1

Dimensions for other colors are identical.

NEMA and IEC Terminal Block Component SpecificationsTie Point Terminal Blocks Type HM2C and WD4C

The total current flow through these terminal blocks (the sum of all inputs or the sum of all outputs) must not exceed the rated current for the device.

Description Type Rating

Maximum Total Current Flow Through the Terminal Block H2C, HM2C 10 A

Maximum Working Voltage H2C, HM2C 600V

Operating Ambient Temperature Range All -4+104 F (-20+40 C)

Storage Temperature Range All -40+167 F (-40+75 C)

Diode Terminal Blocks Types H2D, HHM2D, WD2D, WD2DR, RD3DF and RD3DR

Description Symbol Type Rating

Peak Repetitive Reverse Voltage V (RRM) H2D, HM2D 600V

Working Peak Reverse Voltage V (RWM)V (R)RD3DF, RD3DRWD4DF, WD4DR 300V

Non-Repetitive Peak Reverse Voltage (Halfwave, single-phase, 60 Hz) V (RSM) H2D, HM2D 600V

RMS Reverse Voltage V (Rms) H2D, HM2D 600V

Average Rectified Forward Current Single-Phase, Resistive Load, 60 Hz I (O) All 1.0 A

Non-Repetitive Peak Surge Current (Surge applied at rated load) I (FSM) All 30 A (1 cycle)

Maximum Forward Voltage Drop [I (f) = 1.0 A] V (F) All 1.1V

Maximum Reverse Current I (R) All 10 AOperating Ambient Temperature Range T (A) All 4+104 F (20+40 C)

Storage Temperature Range T (S) All 40+167 F (40+75 C)

The maximum voltage rating of the diode terminal blocks listed in the above table should not be exceeded even through the maximum reverse voltage rating ofthe diode alone is 1000V.

All parameters measured at 77 F (25 C).

jeffmRectangle

Bulletin 1492

Screw Connection Terminal Blocks

12-39

Fuse Blocks

0

1

2

3

4

5

6

7

8

9

10

11

12

13

1492-H... 1492-WFB4

Dimensions are not intended to be usedfor manufacturing purposes.Note: Height dimension is measured

from top of rail to top of terminalblock.

0.36"(9.1 mm)

3.20" (81.3 mm)

1.85

" (47

mm)

0.31"(8 mm)

2.0" (50.7 mm)

1.55

" (39

.4 mm

)

Specifications Single-circuit fusible terminal block with or without fuseindication. Single-circuit fuse block with or without fuse indication.

Certifications CSA IEC CSA IEC

Voltage RatingH6/WFB4 300V AC/DC 500V AC/DC 300V AC/DC 500V AC/DC

H5/WFB424 1057V AC/DC 1057V AC/DCH4/WFB4250 100300V AC 85264V AC

Maximum Current 15 A 15 A 15 A

Wire Range (Rated Cross Section) #3012 AWG 0.54 mm2 #3012 AWG 0.54 mm2

Wire Strip Length 0.38 in. (9.7 mm) 0.31 in. (8 mm)Recommended Tightening Torque 7.1 lbin (0.8 Nm) 2.655.3 lbin (0.30.6 Nm)Density 33 pcs/ft (109pcs /m) 38 pcs/ft (125 pcs/m)Housing Temperature Range -40+195 F (-40+90 C) -40+195 F (-40+90 C)

Indicator TypeH6/WFB4 Non-Indicating Non-IndicatingH5/WFB424 Red LED Red LEDH4/WFB4250 Neon Neon

Leakage CurrentH6/WFB4 H5/WFB424 2 mA @ 24V 2 mA @ 24VH4/WFB4250 2 mA @ 300V 2 mA @ 300VFuse Size (Not Supplied) 1/4 x 1-1/4 in. 5 x 20 mmShort-Circuit Current Rating See page 12-42

Terminal Blocks Cat. No. Pkg Qty. Cat. No. Pkg Qty.

Color:Black No-indication 1492-H6 25 1492-WFB4 50

Black w/LED 1492-H5 25 1492-WFB424 50Black w/Neon 1492-H4 25 1492-WFB4250 50

Accessories Cat. No. Pkg Qty. Cat. No. Pkg Qty.Mounting Rails:1 m Symmetrical DIN (Steel) 199-DR1 10 199-DR1 10

1 m Symmetrical DIN (Aluminum) 1492-DR5 10 1492-DR5 101 m Hi-Rise Sym. DIN (Aluminum) 1492-DR6 2 1492-DR6 21 m Angled Hi-Rise Sym. DIN (Steel) 1492-DR7 2 1492-DR7 2

3 ft Scored A-B Rail 1492-N1 20 3 ft Rigid A-B Rail 1492-N22 20 3 ft High Rise A-B Rail 1492-N44 2 Standoff Brackets (Use Every 12 in.) 1492-N25 2 End Barrier 1492-N37 50 Not Required End Anchors and Retainers:Screwless End Retainer 1492-ERL35 20 1492-ERL35 20

DIN Rail Normal Duty 1492-EAJ35 100 1492-EAJ35 100DIN Rail Heavy Duty 1492-EAHJ35 50 1492-EAHJ35 50A-B Rail Heavy Duty 1492-N23 10

10-Pole Side Jumper 1492-N49 10 1492-SJFB8-10 10Side Jumper Insulating Sleeve 1492-SJS 10

Other Accessories:Partition Plate 1492-PPSL3 50

Marking Systems:Snap-In Marker Card For BaseBlock

5 1492-MS8X12 (56/card) 5

5 1492-MS8X9 (56/card) 5

For Handle1492-MS8X12 (56/card) 5

1492-MS8X9 (56/card) 51492-MS8X9 (56/card) 5

Adhesive Labels 1492-ALHFB (50/sheet) 1 1492-ALHFB (50/card) 1

IEC standards for 5 x 20 mm fuses do not include ratings above 6.3 A.

Cat. No. 1492-N49 is uninsulated. Cat. No. 1492-SJFB8-10 is insulated.



jeffmRectangle

jeffmRectangle

Bulletin 1492


12-86

Jumpers

0

1

2

3

4

5

6

7

8

9

10

11

12

13

Side Jumpers

Two-Level Jumper

For Use WithPkgQty. Cat. No.

1492-LTF3(Connects Two Levels within a 1492-LTF3

Terminal Block)20 1492-CJL5D


1492-WM4, W4 50 1492-N42

1492-H4, H5, H6, H710 1492-N49

10 1492-SJS

1492-W3, WR3 10 1492-SJ5-10

1492-JD3, JD3C, JD3F, JDG3, JD3DF,JD3DR, JD3SS, JDG3P 50 1492-SJ5A-10


1492-JD3, JD3C, JD3F, JDG3, JD3DF,JD3DR, JD3SS, JDG3P 50 1492-SJ5B-24


1492-WM4, W4, W4TW 10 1492-SJ6-10

1492-JT3M 5 1492-SJ6A-50

1492-W10 10 1492-SJ8-10

1492-JD3FB, JDG3FB 50 1492-SJ8A-4

1492-JD3FB, JDG3FB 50 1492-SJ8A-3

1492-JD3FB, JDG3FB 50 1492-SJ8A-2

1492-LMP3, LMP3Q, LMJ3, LM3, LM3Q,LMP3E, LMP3QE 50 1492-SJLM5-2

1492-WMD1 10 1492-SJMD5-12

1492-WFB4, WFB424, WFB4250 10 1492-SJFB8-10

1492-WM3 10 1492-SJM5-10

1492-WTF3, WTS3, WTF3LP, WTS3LP,WTF3LP, WTF3LN, WTS3LN 10 1492-SJT5-20-R

1492-WTF3, WTS3, WTF3LP, WTS3LP,WTF3LP, WTF3LN, WTS3LN 10 1492-SJT5-20-B

Note: Side jumpers carry the same current rating as the terminal block usedwith it Side jumper insulating sleeve only for use with Cat. No. 1492-N49 Use jumper on single side of terminal block only Uninsulated



Technical Specifications for Fuse Plugs

UL/CSA File and Guide Numbers Arranged by Base Cat. Nos.

Characteristic 1492-FPK2 1492-FPK224 1492-FPK248 1492-FPK2120 1492-FPK2250

Indicator Type Non-Indicating LED LED LED LED

Leakage Current 1.6 mA @ 24V 1.6 mA @ 24V 1.6 mA @ 24V 1.6 mA @ 264V

Working Voltage Per Fuse Rating 1036V AC/DC 3570V AC/DC 60150V AC/DC 140250V AC

Fuse Size 5 x 20 mm

Marker 1492-M5X5

IEC standards for 5 x 20 mm fuses do not include ratings above 6.3 A.

Base Cat. No.

UL Number CSA Number

File Guide File Class

1492-H4, -H5, -H6, -H7 E40735 XCFR2 LR67896 622801

1492-R E40735E187022

XCFR2XCIB2XCFR8

1492-RGE160646E40735E187022

KDER2XCFR2XCIB2

1492-UF3 E40735 XCFR2 LR67896 622801

1492-W E40735E187022XCFR2XCIB2

LR67896LR14074

622801622801

1492-WG E40735E187022XCFR2XCIB2

LR67896LR14074

622801622801

1492-J E40735 XCFR2XCIB2 223923622801622801

1492-JG E40735E187022XCFR2XCIB2 223923

622801622801

1492-L E40735E187022XCFR2XCIB2 223923

622801622801

1492-LG E40735E187022XCFR2XCIB2 223923

622801622801

These numbers are actually UL file and guide numbers, as these products are UL Recognized Components per Canadian Safety Standards (cUR).

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Specifications

12-98

Bulletin 1492




Bulletin 1492


12-95

Specifications

0

1

2

3

4

5

6

7

8

9

10

11

12

13

Maximum number of multiple wire connections for copper conductors of the same cross-section and type for Allen-Bradley IEC TerminalBlocks. Cat. Nos. 1492-J and L products are all recommended for one conductor per terminal. Wire range is defined in the cat. page for eachof the products.

In general, accessories for terminal blocks are not eligible for recognition by UL, CSA, or other third party approval agencies. The suitability ofthe installation must be judged in the end use application due to the wide variety of possible uses. However, accessories are designed tomeet, and are tested to, the terminal block assembly requirements such as electrical spacings, etc.

Cat. No.

Wire Size [AWG]

#30 #28 #26 #24 #22 #20 #18 #16 #14 #12 #10 #8 #6 #4 #2 #1 1/0 2/0 3/0

Number of the Same Size Wires Per Terminal

1492-CA1 4 4 4 3 2 2 1 1

1492-CAM1 4 4 4 3 2 2 1 1

1492-H4 1 1 1 1 4 4 3 2 2 1 1

1492-H5 1 1 1 1 4 4 3 2 2 1 1

1492-H6 1 1 1 1 4 4 3 2 2 1 1

1492-H7 1 1 1 1 4 4 3 2 2 1 1

1492-HM3 4 4 4 3 2 2 1 1

1492-J10 4 4 4 4 3 2 1 1 1

1492-J16 1 4 4 3 2 1 1 1

1492-J2Q 4 4 4 3 1 1 1 1

1492-J3 4 4 4 4 4 4 3 3 2 1

1492-J35 3 3 3 2 2 1 1 1 1

1492-J3F 4 4 4 4 4 4 3 3 2 1

1492-J3P 4 4 4 4 3 3 3 3 2 1

1492-J3TW (single side) 4 4 4 4 4 4 3 3 2 1

1492-J3TW (twin side) 4 4 4 3 1 1 1

1492-J4 4 4 3 3 2 1 1

1492-J4CTB 1 1 4 4 3 3 2 1 1

1492-J4Q 1 1 1 1 1 4 3 3 2 1 1

1492-J4TW 1 1 1 1 1 4 3 3 2 1 1

1492-J50 1 2 2 1 1 1 1

1492-J6 4 4 3 3 3 2 1 1

1492-J70 5 5 5 2 2 2 1 1 1 1 1

1492-JC3 4 4 4 3 1 1 1 1

1492-JD3 4 4 4 4 4 4 3 2 2 1

1492-JD3DF 4 4 4 4 4 4 3 2 2 1

1492-JD3DR 4 4 4 4 4 4 3 2 2 1

1492-JD3F 4 4 4 4 4 4 3 1 1 1

1492-JD3FB 4 4 4 4 4 4 3 3 2 1

1492-JD3PSS 4 4 3 2 1 1

1492-JD3PSSTP 4 4 3 2 1 1

1492-JD3PTP 4 4 3 2 1 1

1492-JD3RB*** 4 4 4 4 4 4 3 2 2 1

1492-JD3RC001 4 4 4 4 4 4 3 2 2 1

1492-JD3SS 4 4 4 4 4 4 3 2 2 1

1492-JD4 1 1 1 4 3 3 2 1 1

1492-JD4C 1 1 1 4 3 3 2 1 1

1492-JDC3 4 4 4 4 4 4 3 2 2 1

1492-JDG3 4 4 4 4 4 4 3 2 2 1

1492-JDG3FB 4 4 4 4 4 4 3 3 2 1

1492-JDG3P 4 4 3 2 1 1

1492-JDG3PSS 4 4 3 2 1 1

1492-JDG3PSSTP 4 4 3 2 1 1

1492-JDG3PTP 4 4 3 2 1 1

1492-JDG4 1 1 1 4 3 3 2 1 1



jeffmLine

jeffmRectangle

Bulletin 1492




0

1

2

3

4

5

6

7

8

9

10

11

12

13 The 1492-SJS Insulating Sleeve reduces exposure to live parts on the 1492-N39 and 1492-N49. The 1492-SJS used with the 1492-N39 and 1492-H1 or 1492-

HM1 provides IEC 947 IP2X finger protection.

1492-EAHJ35

1492-N2

.013 (3.2 mm)

1492-N23

0.56(14.3 mm)

1.44 (36.5 mm)

1.25

(31

.8 m

m)

1492-N47

0.34(8.6 mm)

1.50 (38.1 mm)

1.70

(43

.2 m

m)

End Anchors

Cat. No. A B C D E

1492-15A 1.5 in.(38.1 mm)1.03 in.

(26.2 mm)0.594 in.

(15.1 mm)0.234 in.(5.9 mm)

0.75 in.(19.1 mm)

1492-15E 1.5 in.(38.1 mm)1.03 in.

(26.2 mm)0.594 in.

(15.1 mm)0.234 in.(5.9 mm)

1492-25A 1.88 in.(47.8 mm)1.19 in.

(30.2 mm)0.688 in.

(17.5 mm)0.203 in.(5.2 mm)

0.97 in.(24.6 mm)

1492-25E 1.88 in.(47.8 mm)1.19 in.

(30.2 mm)0.688 in.

(17.5 mm)0.234 in.(5.9 mm)

1492-15A, 1492-25A 1492-15E, 1492-25E

A = WidthB = Height

A

D C

E

A = WidthB = Height

DC

jeffmRectangle

Bulletin 1492-FBFuse HoldersUL Listed for Branch Circuit Protection

Overview

The Allen-Bradley Bulletin 1492-FB fuse holder line from Rockwell Automation has a distinctive, standalone design with many unique features. These fuse holders provide ease of use and installation (no special tools are needed), with a versatile, space saving and nger-safe design. This product line also stands out among the competition because of its distinct look, marker ready feature, and expanded ventilation. The fuse clips are silver-plated for improved fuse contact and there is a standardized LED indication feature for both AC and DC voltages.

The class CC and J holders are UL listed for branch circuit protection. Class CC and J fuses are ideal for wire protection, small motor loads, and for group protection of small motor loads. The midget holders are a UL recognized product where supplementary (1 1/2 x 13/32) fuses are applied. The midget fuse holder is also approved for 10 x 38 IEC midget fuses.

The 1492-FB fuse holder family is designed for use in many OEM applications such as power supplies, equipment protection, primary and secondary control transformers, solenoids, lighting and heater loads, and drives.

Features and Bene ts Silver-plated fuse clips

Improved fuse contact

Available bus bars 80 A and 100 A ampacity UL, CSA, CE certi ed

Ventilated housing Allows good air ow and

fuse ventilation

Marker-ready feature For circuit and wire identi cation

Optional blown fuse indicator Allow easy troubleshooting

of electrical circuits

Finger-safe design Front- nger protection per

IEC/ EN 60529 protects fromaccidental contact withenergized circuits

Compact size Requires less panel space than

open-style fuse holders

No special tools required Easy insertion/removal of fuses

Versatile Versions for 12V to 1000V 1-, 2-, and 3-pole versions

Safe, compact and unique design, now ampli ed by the bus bar o ering

Allen-Bradley and Rockwell Software are trademarks of Rockwell Automation, Inc.Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 1492FB-PP001G-EN-P April 2011 Copyright 2011 Rockwell Automation, Inc. All Rights Reserved. Printed in USA. Supersedes Publication 1492FB-PP001F-EN-P March 2010

Product SelectionFuse Holders

Speci cations

Product Type(n = # of poles)

CC M J30 J601492-FBnC30 B

1492-FB1C30-D1 B1492-FBnC30-L B

1492-FBnM30 B1492-FB1M30-D1 B

1492-FBnM30-L B1492-FBnJ30 B

1492-FBnJ30-L B1492-FBnJ60 B

1492-FBnJ60-L B

For Fuse Type:Class CC

Midget13/32 X 1 1/2

10 x 38 mm Class JApprovals UL, CSA, CE UR, CSA, CE UL, CSA, CE

Maximum Voltage 600V Max 600V Max(690V AC max IEC) 600V Max

Maximum Current 30 A 30 A(32 A IEC) 30 A 60 A

Maximum Current Withstand(UL/CSA)

(This is the rating of the fuse not the holder.)200 kA sym Fuse Dependent50 kA max UL 200 kA sym

Operating Temperature Range -4 130 F-20 55 CConductor Material Cu, Stranded

ConductorStrip Length

0.43 in(11 mm)

0.79 in (20 mm)

Conductor Range

One wireper Terminal

#18 4 AWG(0.75 25 mm2)

#18 1 AWG(0.75 50 mm2)

#14 1 AWG(2.5 50 mm2)

Two wiresper Terminal

(both wires must be same size)

#18 8 AWG(0.75 10 mm2)

#18 6 AWG(0.75 16 mm2)

#14 #6 AWG(2.5 16 mm2)

TerminalTightening Torque

# 18 # 8 22 lbin#6 #4 26 lbin

(0.75 25 mm2 2.5 nm)

35 lbin(4 nm)

DescriptionFor Class CC Fuse For Class J Fuse For Midget Fuse

30 A* 30 A 60 A 30 ACat. No. Cat. No. Cat. No. Cat. No.

1-Pole

Fuse Holder 1492-FB1C30 1492-FB1J30 1492-FB1J60 1492-FB1M30Fuse Holder with Indication (110-600V) 1492-FB1C30-L 1492-FB1J30-L 1492-FB1J60-L 1492-FB1M30-LFuse Holder with Indication, 1272V 1492-FB1C30-D1 1492-FB1M30-D1

Pieces per Carton 6

2-PoleFuse Holder 1492-FB2C30 1492-FB2J30 1492-FB2J60 1492-FB2M30

Fuse Holder with Indication 1492-FB2C30-L 1492-FB2J30-L 1492-FB2J60-L 149-FB2M30-LPieces per Carton 3

3-PoleFuse Holder 1492-FB3C30 1492-FB3J30 1492-FB3J60 1492-FB3M30

Fuse Holder with Indication 1492-FB3C30-L 1492-FB3J30-L 1492-FB3J60-L 1492-FB3M60-LPieces per Carton 2

* All major fuse brands and current ranges have been evaluated for this fuse holder. Due to the heat they generate, the following fuses must be de-rated:Ferraz Shamut ATQR 1.25 1 = 0.42 A max.Ferraz Shamut ATQR 1.40 1 = 0.47 A max.

Description Devices per Meter Package QuantityBus Protection

Max. Fuse Type J Ampacity Cat. No.

1-Phase 57

(1) 1 Meter Bus Bar

175 A 80 A 1492-A1B8200 A 100 A 1492-A1B1

2-Phase 29175 A 80 A 1492-A2B8200 A 100 A 1492-A2B1

3-Phase 19175 A 80 A 1492-A3B8200 A 100 A 1492-A3B1

End Cap for 1-Phase 10 1492-A1EEnd Cap for

2-Phase & 3-Phase 10 1492-AME

Protective Shroud 10 1492-AAPTerminal Lug 10 80 A/100 A 1492-AAT1

AccessoriesBus Bars, Pin Style, When used with 1492-FB, type CC fuse holders, 600V ACCuttable, copper bus bar provided in 1 m length. UL 508 Listed, E56639, Category NMTR, cULus. CE to IEC 664 100 kA SCCR when used with Bus Protection, noted in table below. Bus bars may also be used with 1492-FB - midget (10 x 38) fuse holders and 1492-SP Miniature Circuit Breaker/Supplementary Protector

Bulletin 1492


12-86

Jumpers

0

1

2

3

4

5

6

7

8

9

10

11

12

13

Side Jumpers

Two-Level Jumper


1492-LTF3(Connects Two Levels within a 1492-LTF3

Terminal Block)20 1492-CJL5D


1492-WM4, W4 50 1492-N42

1492-H4, H5, H6, H710 1492-N49

10 1492-SJS

1492-W3, WR3 10 1492-SJ5-10





1492-WM4, W4, W4TW 10 1492-SJ6-10

1492-JT3M 5 1492-SJ6A-50

1492-W10 10 1492-SJ8-10

1492-JD3FB, JDG3FB 50 1492-SJ8A-4

1492-JD3FB, JDG3FB 50 1492-SJ8A-3

1492-JD3FB, JDG3FB 50 1492-SJ8A-2

1492-LMP3, LMP3Q, LMJ3, LM3, LM3Q,LMP3E, LMP3QE 50 1492-SJLM5-2

1492-WMD1 10 1492-SJMD5-12

1492-WFB4, WFB424, WFB4250 10 1492-SJFB8-10

1492-WM3 10 1492-SJM5-10

1492-WTF3, WTS3, WTF3LP, WTS3LP,WTF3LP, WTF3LN, WTS3LN 10 1492-SJT5-20-R

1492-WTF3, WTS3, WTF3LP, WTS3LP,WTF3LP, WTF3LN, WTS3LN 10 1492-SJT5-20-B

Note: Side jumpers carry the same current rating as the terminal block usedwith it Side jumper insulating sleeve only for use with Cat. No. 1492-N49 Use jumper on single side of terminal block only Uninsulated



jeffmHighlight

1492-W3 1492-W4 1492-W6


from top of rail to top of terminalblock. 0.20"

(5 mm)

1.78" (45.3 mm)1.

38"

(35 m

m)

0.24"(6 mm)

1.78" (45.3 mm)

1.38

" (35

mm)

0.28"(7 mm)

1.87" (47.6 mm)

1.61

" (41

mm)

Specifications Single-circuit terminal block. Single-circuit terminal block. Single-circuit terminal block.Certifications IEC CSA ATEX IEC CSA ATEX IEC CSA ATEX

Voltage Rating 600VAC/DC800V

AC/DC600V

AC/DC550V

AC/DC600V

AC/DC800V

AC/DC600V

AC/DC550V

AC/DC600V

AC/DC800V

AC/DC600V

AC/DC550V

AC/DCMaximum Current 20 A 24 A 20 A 24 A 30 A 32 A 30 A 32 A 40 A 41 A 40 A 41 A

Wire Range (Rated Cross Section) #3014AWG0.52.5

mm2#2214

AWG 2.5 mm2 #2210

AWG0.54.0

mm2#2210

AWG 4.0 mm2 #2210

AWG0.56.0

mm2#2210

AWG 6.0 mm2

Wire Strip Length 0.39 in. (10 mm) 0.35 in. (9 mm) 0.47 in. (12 mm)Recommended Tightening Torque 5.05.6 lbin (0.6 Nm) 5.05.6 lbin (0.6 Nm) 5.66.8 lbin (0.7 Nm)Density 61 pcs/ft (200 pcs/m) 50 pcs/ft (166 pcs/m) 43 pcs/ft (142 pcs/m)Housing Temperature Range -40+195 F (-40+90 C) -40+195 F (-40+90 C) -40+195 F (-40+90 C)

Terminal Blocks Cat. No.PkgQty. Cat. No.

PkgQty. Cat. No.

PkgQty.

Color: Grey 1492-W3 50 1492-W4 50 1492-W6 50Red 1492-W3-RE 50 1492-W4-RE 50 1492-W6-RE 50Blue 1492-W3-B 50 1492-W4-B 50 1492-W6-B 50

Black 1492-W3-BL 50 1492-W4-BL 50 1492-W6-BL 50Green 1492-W3-G 50 1492-W4-G 50 1492-W6-G 50Yellow 1492-W3-Y 50 1492-W4-Y 50 1492-W6-Y 50

Orange 1492-W3-OR 50 1492-W4-OR 50 1492-W6-OR 50Brown 1492-W3-BR 50 1492-W4-BR 50 1492-W6-BR 50White 1492-W3-W 50 1492-W4-W 50 1492-W6-W 50

Accessories Cat. No.PkgQty. Cat. No.

PkgQty. Cat. No.

PkgQty.

Mounting Rails:1 m Symmetrical DIN (Steel) 199-DR1 10 199-DR1 10 199-DR1 10

1 m Symmetrical DIN (Aluminum) 1492-DR5 10 1492-DR5 10 1492-DR5 101 m Hi-Rise Sym. DIN (Aluminum) 1492-DR6 2 1492-DR6 2 1492-DR6 21 m Angled Hi-Rise Sym. DIN (Steel) 1492-DR7 2 1492-DR7 2 1492-DR7 2

End Barrier 1492-EB3 50 1492-EB3 50 1492-EB10 50End Anchors and Retainers:Screwless End Retainer 1492-ERL35 20 1492-ERL35 20 1492-ERL35 20

DIN Rail Normal Duty 1492-EAJ35 100 1492-EAJ35 100 1492-EAJ35 100DIN Rail Heavy Duty 1492-EAHJ35 50 1492-EAHJ35 50 1492-EAHJ35 50

Jumpers:Insulated Side Jumper 1492-SJ5-10 (10-pole) 10

1492-N42 (2-pole) 50

1492-SJ6-10 (10-pole) 10Center Jumper 50-pole 1492-CJ5-50 5 1492-CJ6-50 5 Center Jumper 40-pole 1492-CJ7-40 5Center Jumper 10-pole 1492-CJ5-10 10 1492-CJ6-10 10 1492-CJ7-10 10Center Jumper 5-pole 1492-CJ5-5 10 1492-CJ6-5 10 1492-CJ7-5 10Center Jumper 4-pole 1492-CJ5-4 10 1492-CJ6-4 10 1492-CJ7-4 10Center Jumper 3-pole 1492-CJ5-3 10 1492-CJ6-3 10 1492-CJ7-3 10Center Jumper 2-pole 1492-CJ5-2 10 1492-CJ6-2 10 1492-CJ7-2 10Center Jumper Link 1492-CJL5 10 1492-CJL6 10 1492-CJL7 10Center Jumper Cover White 1492-CJCW5 20 1492-CJCW6 20 1492-CJCW6 20

Other Accessories:Partition Plate 1492-PP3 50 1492-PP3 50 1492-PP10 50

Separation Plate 1492-SP3 50 1492-SP3 50 Test Plug 1492-TP28 10 1492-TP28 10Stackable Test Plug (with Legs) 1492-TP6EWL 10 Stackable Test Plug (without Legs) 1492-TP6E 10 Test Plug Adapter 1492-TA285 10 1492-TA40 10 1492-TA40 10Electrical Warning Plate (1-pole) 1492-EWP5 10 1492-EWP6 10 1492-EWP7 10Electrical Warning Plate (4-pole) 1492-EWP5-4 10 1492-EWP6-4 10 1492-EWP7-4 10

Marking Systems:Snap-in Marker Cards 1492-MS5X12 (80/card) 5 1492-MS6X12 (80/card) 5 1492-MS6X12 (80/card) 5

May only be used as a marking surface. Cannot be installed over a center jumper.13

12

11

10

9

8

7

6

5

4

3

2

1

0

Space-Saver Feed-Through Blocks

12-11

Bulletin 1492




jeffmHighlight

Bulletin 1492


12-16

Specialty Feed-Through Blocks

0

1

2

3

4

5

6

7

8

9

10

11

12

13

1492-W4TW 1492-WR3 1492-J4M


from top of rail to top of terminalblock. 0.24"

(6 mm)

2.05" (52.1 mm)

1.64

" (41

.6 mm

)

0.20"(5 mm)

1.78" (45.3 mm)

1.99

" (50

.5 mm

)

0.965"(24.5 mm)

2.36" (60 mm)

1.56

" (39

.5 mm

)

Specifications Feed-through terminal block with 3connection points, 2 on one sideSingle-circuit terminal block with

terminals on common side.Motor connection terminal blockcluster with 3 feeds and ground

Certifications CSA IEC CSA IECCertifications onindividual blocks(1492-J4, JG4)

Voltage Rating 600VAC/DC600V

AC/DC800V

AC/DC 300V AC/DC500V

AC/DCMaximum Current 30 A 20 A 32 A 15 A 15 A

Wire Range (Rated Cross Section) #1810AWG#2212

AWG 0.54 mm2 #2214 AWG 0.52.5mm2

#2210 AWG 4 mm2

Wire Strip Length 0.35 in. (9 mm) 0.39 in. (10 mm) 0.39 in. (10 mm)Recommended Tightening Torque 5.05.6 lbin (0.6 Nm) 5.05.6 lbin (0.6 Nm) 9.0 lbin (1.0 Nm)Density 50 pcs/ft (166 pcs/m) 61 pcs/ft (200 pcs/m) 12 pcs/ft (40 pcs/m)Housing Temperature Range -40+195 F (-40+90 C) -40+195 F (-40+90 C) -58+248 F (-50+120 C)Short-Circuit Current Rating See page 12-42

Terminal Blocks Cat. No. Pkg Qty. Cat. No. Pkg Qty. Cat. No. Pkg Qty.Color: Grey 1492-W4TW 50 1492-WR3 50

Grey/Green/Yellow 1492-J4M 20Red 1492-W4TW-RE 50 Blue 1492-W4TW-B 50

Black 1492-W4TW-BL 50 Green 1492-W4TW-G 50 Yellow 1492-W4TW-Y 50

Orange 1492-W4TW-OR 50 Brown 1492-W4TW-BR 50 White 1492-W4TW-W 50

Accessories Cat. No. Pkg Qty. Cat. No. Pkg Qty. Cat. No. Pkg Qty.Mounting Rails:1 m Symmetrical DIN (Steel) 199-DR1 10 199-DR1 10 199-DR1 10

1 m Symmetrical DIN (Aluminum) 1492-DR5 10 1492-DR5 10 1492-DR5 101 m Hi-Rise Sym. DIN (Aluminum) 1492-DR6 2 1492-DR6 2 1492-DR6 21 m Angled Hi-Rise Sym. DIN (Steel) 1492-DR7 2 1492-DR7 2 1492-DR7 2

End Barriers Grey 1492-EB3TW 50 1492-EBR3 50 Not Required End Anchors and Retainers:Screwless End Retainer 1492-ERL35 20 1492-ERL35 20 1492-ERL35 20

DIN Rail Normal Duty 1492-EAJ35 100 1492-EAJ35 100 1492-EAJ35 100DIN Rail Heavy Duty 1492-EAHJ35 50 1492-EAHJ35 50 1492-EAHJ35 50

Jumpers:Side Jumper 10-pole insulated 1492-SJ6-10 10 1492-SJ5-10 10

Screw Center Jumper 50-pole 1492-CJ6-50 5 1492-CJD5-50 5 Screw Center Jumper 10-pole 1492-CJ6-10 10 1492-CJD5-10 10 1492-CJJ6-10 20Screw Center Jumper 5-pole 1492-CJ6-5 10 1492-CJD5-5 10 Screw Center Jumper 4-pole 1492-CJ6-4 10 1492-CJD5-4 10 1492-CJJ6-4 50Screw Center Jumper 3-pole 1492-CJ6-3 10 1492-CJD5-3 10 1492-CJJ6-3 50Screw Center Jumper 2-pole 1492-CJ6-2 10 1492-CJD5-2 10 1492-CJJ6-2 50Center Jumper Cover White 1492-CJCW6 20 1492-CJCW5 20 Center Jumper Link 1492-CJL6 10 1492-CJL5 10 Screw Type Jumper Notching Tool 1492-T1 1

Other Accessories:Partition Plate 1492-PP10 50 1492-EBR3 50 1492-EBJ16 20

End Cover 1492-EC3TW 10 Test Plug Socket 1492-TPS23L 50Test Plug 1492-TP28 10 1492-TP23 20Test Adapater 1492-TA40 10 1492-TA285 10 1492-TPJ6 25Electrical Warming Plate 1492-EWPJ5 50

Marking Systems:Snap-in marker cards 1492-MS6X9 (80/card) 5 1492-MS5X9 (80/card) 5

1492-M6X12(120/card) 5

Use side jumpers on the single conductor side only.Provides IP2X Finger Safety when a W4 is mounted on open side of Cat. No. 1492-W4TW. May only be used as a marking surface. Cannot be installed over a center jumper.



jeffmHighlight

Form No. PDB

Page 18 of 23

Data Sheet #1049

07-05-07

BU-SB07255

Terminal Blocks With High Short-Circuit Current Ratings

1.87(47.50)

.62(15.75)

1.44(36.57)

1.71(43.48)

1.46(37.13)

Mtg. holes.18 (4.57) dia.

.28 (7.11) c'bores

DovetailOption

NDN111-WH-UL

Agency/Standards UL 1059 Recognized, Guide XCFR2, File E62622 General Industry Class per UL 1059, usage category C

Electrical 600Vac or dc Short-Circuit Current Rating up to 100kA, See table page 16 90A ampacity Wire range 2 to 18 AWG CU

Mechanical Panel mount 35mm DIN rail and C-rail mount .635 (16.13mm) pole to pole spacing 3 pole configuration Marking tape MT12-12 Flammability, UL94 V2

2F

35www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2013 Eatons Crouse-Hinds Business

2FCondulet Stainless Steel Conduit Device Boxes, Covers and Gaskets

Eaton's Crouse-Hinds Condulet Stainless Steel Device Boxesdeliver power where you need it, saving you time and moneythroughout the life of your facility.Superior resistance to corrosion and heat, combined with unmatchedstrength, make stainless steel Condulet bodies and boxes a long-term solution for even the most extreme environments.

Features: Self-healing properties of stainless steel fittings help reduce the

penetration of rust/corrosion and eliminate damage to the fitting Stainless steel fittings retain their strength in extreme heat and

extreme cold conditions Fitting surface is easy to maintain and keep clean Easy cleaning capabilities make these fittings perfect for food

processing and other hygienic areas where wash downs arecommon

Superior strength and durability greatly reduce replacement offittings - this will lower your total cost of ownership and increaseyour return on investment

Stainless steel fittings do not require harsh environment-damagingcleaners to keep them looking like new

Internal green grounding screw - standard Tapered threads for protection of wire insulation Wide selection of covers available Single or double conduit entry Ample wiring room provided for easy installations

Applications:Cast device boxes are installed in conduit systems to: Accommodate wiring devices Act as pull boxes for conductors in a conduit system Provide openings to make splices and taps in conductors Provide access to conductors for maintenance and future

system changes Connect conduit systems

Standard Materials: Bodies - 316 stainless steel Covers - 316 stainless steel Cover Screws - 316 stainless steel Gasket - neoprene

Certifications and Compliances: UL Standard 514A CSA Standard C22.2 No. 18.1-04 Raintight - when installed with cover and gasket

DimensionA Length of boxB Overall length (including hubs)C Width of boxD Overall width (including hubs)E Height of boxF Overall height (including hubs)

2F

36 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2013 Eatons Crouse-Hinds Business

2F

Ordering Information

FDC Device Body

FDS Device Body

FDA Device Body

FDX Device Body

Ordering Information - Device Box Cover and Gasket

Blank Cover

Switch Formed Cover

Blank Formed Cover

Receptacle Formed Cover

Condulet Stainless Steel Conduit Device Boxes,Covers and GasketsThe Ultimate in Corrosion Resistance and Durability

Catalog Number

DS7000BC

Catalog Number

DS7000SF

Catalog Number

DS7000BF

Catalog Number

DS7000RF

Catalog Number Trade Size A B C D E F

FDC2SS 3/4" 4.63 6.19 2.94 2.94 3.03 3.03


FDS2SS 3/4" 4.63 5.41 2.94 2.94 3.03 3.03


FDA2SS 3/4" 4.63 4.63 2.94 2.94 3.03 3.80


FDX2SS 3/4" 4.63 6.19 2.94 4.50 3.03 3.03

FD Device Body


FD2SS 3/4" 4.63 5.41 2.94 2.94 3.03 3.03

Device Boxes, Covers & AccessoriesT&B Catalog Number:

IH3-1UPC Number: 04226939210Status: ActiveDescription:1-gang silver universal weatherproof box with 3 -1/2 in. holes, 17.3 cu.in.Features

Alloy A380 aluminum, certified zinc alloy and stain-less steel springs provide increased corrosion resis-tanceDie Cast construction and industrial design com-bine to produce a rugged protective enclosure fordevices.Clean cover edges provide good gasket sealing.Precision cast and machined surfaces permit saferwire pulling.Clear UL and cubic content markings speed ap-proval by inspectorsConvenient mounting lugs for a variety of mountingmethodsSecurely fastened mounting plates reduce costlycall backs

Application

Dry-tite boxes and covers protect wiring devices,switches, electronic components and terminalblocks in dry, damp and wet locationsAccessible wiring chamber provides a convenientlocation to maintain or change a system, pull con-ductors and make splicesJunction box for branch conduits

General

Material Die Cast AluminumFinish Powder-coatedColor SilverVolume (cu.in.) 17Number of Gangs OneDimension Information

Hub Size (inches) 1/2A (inches) 4 9/16B (inches) 2 13/16C (inches) 2D (inches) 5/8G (inches) 3 1/4H (inches) 1 7/8J (inches) 1 1/2Packaging

T&B Inner Pack 1Package in Units 50T&B Sold in UOM EachT&B Weight Per UOM 0.53 lbs. EachApplication Support

D-Pak Merchandising System Available on WebsiteIndustry Cross Reference Available on WebsiteNotes

Rain tight when used with appropriate Red Dot cov-ers.

Certifications

RoHS Compliance YesCertifications

File Nbr:E 28688

For further technical assistance, please contact us...

Thomas & Betts - USA8155 T&B Blvd.Memphis, TN 38125www.tnb.com

T&B Technical SupportMS 3B-508155 T&B Blvd.Memphis, TN 38125

Hours: 7AM - 6PM CDTMonday-FridayPhone: (888) 862-3289Fax: (901) 252-1321Email:[email protected]

[RTD] TEMPERATURE2 WIRE TRANSMITTER

MODEL SM812EC

DESCRIPTION

Conversion of RTD, (Resistance Temperature Detector)signals is accomplished using the DEVAR ModelSM812EC signal transmitter. Surface mount technologyprovides a slim profile allowing the SM812EC to mountdirectly within miniature thermal connection heads. TheSM812EC accommodates Pt 100 RTDs and providesa 4 to 20 mA output current proportional to the detectedtemperature.

The SM812EC is available in a varety of precalibratedtemperature ranges. The span and zero potentiometersprovide span and zero adjustments of + 25% of thenormal range. Standard ranges, model numbers andRTD resistance values at 0, 25, 50, 75, and 100% arelisted in table 1.

SPECIFICATIONS

Accuracy:+ 0.1% span, includes effects of linearity, hysterisis, and repeatability referred to temperature input.

Nonlinearity:0.1% relative to a 100 Pt RTD, = 0.00385 standard curve for nominal range.4:1 minimum improvement on nonlinearity otherwise.

Thermal Effect:1) Zero Shift of + 0.02% / Span / F2) Span Shift of + 0.02% / Span / F

Circuitry:Epoxy EncapsulatedAnalog Circuitry w/ sealed potentiometers.

Power Supply:1) Working voltage of 8.5 to 35 VDC2) Supply Voltage Effect < + 0.001% / Span / Volt

Loop Considerations:1) Loop Resistance Load Effect < + 0.002% Span / 300 Ohms2) Maximum Loop resistance (V supply -8.5V) / 20mA

RFI immunity:Rated class 3-C: 0.25% of span per SAMA PMC33.1 -1987-2abc

Frequency Response:Output -3dB @ 3Hz Input

Temperature range:1) Ambient: -13 to 185F2) Storage: -85 to 257F

Humidity: 0 to 95% noncondensing

Input:100 Pt RTD, = 0.00385

Output:1) Signal range: 4 to 20 mADC2) Absolute Limit: 2 to 29 mA3) Open RTD Indication: Output > 22mA

Calibration Range Adjustabilty:1) Zero 25% of normal span2) Span 25% of normal span

* LOW COST

* THERMO-HEAD INSTALLATION

* 0.1% ACCURACY

* LOW 8.5 VDC DROP

BULLETIN SM812EC 4/02706 Bostwick Ave, Bridgeport, CT 06605-2396TEL: 203-368-6751, TOLL FREE 1-800-566-6822FAX: 203-368-3747http://www.devarinc.com e-mail: [email protected]

Table 1: Input Ranges

( = 0.00385 100 Pt RTD Values at % of input Span)

Model Range F 0% 25% 50% 75% 100% -0011 -40/120 84.27 93.03 101.74 110.38 118.97 -0012 0/200 93.03 103.90 114.68 125.37 135.97 -0013 0/300 93.03 109.30 125.37 141.24 156.90 -0014 0/500 93.03 120.04 146.48 172.36 197.69 -0015 0/750 93.03 133.33 172.36 210.14 246.65 -0016 0/1000 93.03 146.48 197.69 246.65 293.38 -0017 -30/130 86.47 95.21 103.90 112.53 121.11 -0018 40/140 101.74 107.15 112.53 117.90 123.24 -0019 50/85 103.90 105.80 107.69 109.57 111.46 -0021 0/150C 100.00 114.57 128.98 143.23 157.31 -0022 0/100 93.03 98.48 103.90 109.30 114.68 -0023 20/120 97.39 102.82 108.22 113.61 118.97 -0024 0/150 93.03 101.19 109.30 117.36 125.37 -0025 0/200C 100.00 119.40 138.50 157.31 175.84 -0026 30/100 99.57 103.36 107.15 110.92 114.68 -0027 35/85 100.65 103.36 106.07 108.76 111.46 -0028 0/250 93.03 106.61 120.04 133.33 146.48 -0029 -40/25C 84.27 90.69 97.07 103.42 109.73 -0030 0/50C 100.00 104.88 109.73 114.57 119.40 -0031 32/122 100.00 104.88 109.73 114.57 119.40 -0032 -200/0 48.46 59.80 71.00 82.07 93.03 -0033 0/100C 100.00 109.73 119.40 128.98 138.50 -0034 30/110 99.57 103.90 108.22 112.53 116.83 -0035 -100/0C 60.25 70.33 80.31 90.19 100.00 -0036 -50/50C 80.31 90.19 100.00 109.73 119.40 -0037 0/320C 100.00 130.90 161.04 190.45 219.12 -0038 30/130 99.57 104.98 110.38 115.75 121.11 -0039 -30/20 86.47 89.21 91.94 94.67 97.39 -0040 -40/25 84.27 87.84 91.40 94.94 98.48 -0041 30/65 99.57 101.46 103.36 105.25 107.15 -0042 50/100 103.90 106.61 109.30 111.99 114.68

1 9/32"

0.750"

0.375"

0.191" DIA THRU (2) PLACES

1 3/4"

0.269" DIA

LOAD

LOADPOWERSUPPLY

SPANZERO

+

3-WIRERTD

PUMP CONTROLLERMODEL 3020

GENERAL DESCRIPTION

Imagine with a simple touch of a buttonyoull have this controller doing what youwant it to do. Turn a pump on! Turn apump off! Sound an alarm! All easilydone by following the plain English prompts.

The stand alone Model 3020 PumpController accepts all continuous analoglevel inputs. To control level, simply enterthe input range, the units ofmeasurement and the pump controlpoints. If the well or tank is odd shaped,the response of the transducer can becorrected to fit the shape, using the 17point linearization feature.

An isolated 24VDC power output isprovided to power the external leveltrans-mitter.

.

* UP TO 4 PUMP CONTROLS WITH OR WITHOUT ALTERNATION

* 14 SEGMENT L.E.D. DISPLAY FOR TRUE ALPHANUMERICS

* 7.5 AMP S.P.D.T. CONTROL CONTACTS

* 4 TO 20mA, ANALOG RETRANSMISSION AVAILABLE

* 17 POINT STRAPPING TABLE

* LATCHING OR NON-LATCHING RELAYS

Other selectable features include:* Up to 4 sets of on/off control points* The ability to designate each control point as a pump or an alarm* Alternation of pumps (lead/lag)* Flashing of display or sounding of horn during pumping or alarm* Security code lockout --* Sensor failure detection* 0/240 Second trip & reset delay

The 3020 is housed in an 1/8 DINaluminum housing with a splash prooffront panel. The six digit 0.54 inch highLED display provides easy viewing underall ambient light conditions and its 14segment alphanumeric display providesplain English prompting during config-uration. Four active characters displayprocess values between +9999 and-1999. The fourth and fifth charactersdisplay engineering units (e.g. FT., IN.).

SPECIFICATIONS MODEL 3020

INPUT0/20mA, 4/20mA, 0/5V, 1/5V, 0/10V, or -10/10V selected from keypad

Open Input Indication: Indication goes to zero input (Note: for 4/20 mA, zero input will display -25% of span)

Impedance: Voltage input: > 1 Megohms Current input: 10 Ohms

PERFORMANCEAccuracy: 0.01%of input range

A/D Resolution: 20 bits

Display Resolution: +9999 to -1999 in one count steps

Common Mode Rejection: Greater than 120 dB at 50/60 Hz

Normal Mode Rejection: Greater than 64 dB at 50/60 Hz

Operating Temperature: 0 to 70C

Temperature Effect Zero: 0.01% of reading per C

Temperature Effect Span: 0.01% of reading per C

DISPLAYSix bright red LED, 0.54 inch high, 14 segment alphanumericcharacters. Four characters are used for process indication,and two characters for dummy zeros or process descriptors.Display range is +9999 to -1999 counts. Display providesplain English prompts during configuration.

OPTIONS-420 4 to 20mA Analog Retransmission-020 0 to 20mA Analog Retransmission-D232 RS-232 Retransmission-D485 RS-485 Retransmission-005 0 to 5 VDC Retransmission-010 0 to 10 VDC Retransmission-105 1 to 5 VDC Retransmission

-NE4C NEMA 4 Cover-NE4S NEMA 4X Enclosure (1 Unit)-NE4D NEMA 4X Enclosure (2 Units)-NE7 Explosion Proof Housing-M36G 2 Pipe Mount Kit (NE4S,NE4D,NE7)

Note: Analog retransmission ranges can be recalibrated inthe field.

BULLETIN 990027-0004 4/02

Filename d:\data\bulletins\3020.ppt

706 Bostwick Ave, Bridgeport, CT 06605-2396TEL: 203-368-6751, TOLL FREE 1-800-566-6822FAX: 203-368-3747http://www.devarinc.com - e-mail ([email protected])

ENCLOSURE1/8 DIN, polycarbonate bezel, aluminum bodysplash proof front panel

ALARMSStatus Indication: Front panel LEDs, flashing display, horn;flashing display and horn active or inactive, menu selectable

Points: 4 independently set, trip and reset points (100%hysteresis); Alarm action high or low determined byrespective value of trip and reset points

Latching: All alarms can be latching or non latching, menuselectable, reset from keypad

Audible Alarm: An audible alarm can be enabled ordisabled for each channel during configuration; Optionsinclude: 1. Always sound while in alarm, 2. Sounds while inalarm but can be reset from keypad, 3. Sounds during andcontinues after an alarm condition, must be reset fromkeypad, 4. Sounds going into or coming out of alarm,continues sounding until acknowledged

Contacts:SPDT (form C) relays; 1 phase; 7.5 amps at 240 VAC / 24VDC; 1/3HP at 120VAC 7.2FLA; 1/2HP at 240 VAC, 4.9FLA

POWER / VOLTAGEConnections: 15 position, plug-in terminal block for powerand relay contacts; 9 position, plug-in terminal block for input,output and excitation voltage; 24 to 14 AWG

Excitation Voltage: Isolated 24 VDC at 100mA (factory set);Current limit 150mA; isolation strength: 150 VAC

Power Requirement: 90 to 140 VAC, 50/60 Hz, 10VA

SECURITY PASSWORD6 digit security password to enter configuration menu, userselectable, enabled or disabled by internal switch setting

WARRANTY: 2 YEARS Made in USA

ORDERING INFORMATIONMODEL NO. 3020-4 indicator / controller with 4 alarms -XXX select desired options

3020-4-420

Le

ve

l Tra

nsm

itte

rs,

Su

bm

ers

ible

LE

VE

L

DWYER INSTRUMENTS, INC. | www.dwyer-inst.com320

SPECIFICATIONS

Service: Compatible liquids.

Wetted Materials: 316 SS, 316L SS,

epoxy, cable: ETFE or polyurethane.

Accuracy: 0.25% full-scale (includes

linearity, hysteresis, and repeatability).

Temperature Limit: PBLT2: 0 to 200F

(-18 to 93C); PBLTX: 0 to 176F (-18

to 80C).

Compensated Temperature Range:

PBLT2: 0 to 180F (-18 to 82C);

PBLTX: 0 to 176F (-18 to 80C).

Thermal Effect: 0.02% FS/F.

Pressure Limit: 2X full-scale.

Power Requirement: PBLT2: 13 to 30

VDC, PBLTX: 10 to 28 VDC.

Output Signal: 4 to 20 mA DC, two

wire.

Response Time: 50 ms.

Loop Resistance: 900 .

Electrical Connection: Wire pigtail.

Mounting Orientation: Suspended in

tank below level being measured.

Weight: 4.3 lb (2.0 kg).

Electrical Protection: PBLT2:

Lightning and surge protection, PBLTX:

none.

Agency Approvals: PBLT2: None,

PBLTX: CE,cULus intrinsically safe for

Class I, Div. 1, Groups A, B, C, D;

Class II, Div. 1, Groups E, F, G; Class

III,Div. 1. (According to control drawing

01-700797-00).

Submersible Level TransmittersPerfect for Sludge and Slurries, Lightning Protected

Series

PBLT2

&

PBLTX

PBLT2 and PBLTX Submersible Level Transmitters are manufactured for years oftrouble free service in the harshest applications. Both measure the height of liquid abovethe position in the tank referenced to atmospheric pressure. The transmitters consist of apiezoresistive sensing element, encased in a 316 SS housing. Perfect for wastewater andslurry applications with features to protect the unit from these demanding applications.Large diameter 316 SS diaphragm seal is non-clogging and damage resistant to floatingsolids. The PBLT2 incorporates lightning and surge protection utilizing dual arrestor technology,grounded to case, eliminating both power supply surges and lightning ground striketransients (surge protection is not guaranteed and is not covered by warranty). The PBLTXis UL approved intrinsically safe for use in hazardous locations when used with properbarrier.Units come equipped with a 270-pound tensile strength shielded and vented cable.Ventilation tube in the cable automatically compensates for changes in atmosphericpressure above the tank. The vent is protected with a maintenance free filter eliminatingparticulate or water droplets from entering the transducers.

FEATURES

Excellent chemical compatibility with 316 construction and ETFE cable

Lightning and surge protection on PBLT2 models

Maintenance free vent filter

UL approved intrinsically safe on PBLTX models

Large diameter, non-clogging, damage resistant, 316 SS diaphragm seal

APPLICATIONS

Wastewater: Sludge pits, clarifiers, digesters; Alum tanks; Chemical storage tanks;

Oil tanks; Lime slurry; Sumps; Reservoirs.

8-3/32[205.58]

2-3/16[55.56]

BREATHER TUBE

1 [25.40]1/2 NPT

SUBMERSIBLECABLE

60TYP

1/4 x THRU[6.35 x THRU]

3-7/16[87.31] 1/4 [6.35] x THRU

ON A 1-39/64 [40.88] B.C.

7-63/64[202.80]

2-3/16[55.56]

1-1/2[38.10]

1/2 NPT

BREATHER TUBE

SUBMERSIBLECABLE

PBLTX

PBLT2

Cable Length

ft (m)

40 (12.2)

40 (12.2)

60 (18.3)

60 (18.3)

40 (12.2)

40 (12.2)

60 (18.3)

60 (18.3)

16.40 (5)

32.81 (10)

59.06 (18)

Model

PBLT2-5-40

PBLT2-10-40

PBLT2-15-60

PBLT2-20-60

PBLT2-5-40-PU

PBLT2-10-40-PU

PBLT2-15-60-PU

PBLT2-20-60-PU

PBLT2-3.5M-5M-PU

PBLT2-5M-10M-PU

PBLT2-10M-18M-PU

Range psi

(ft w.c.) [m w.c.]

5 (11.54) [3.52]

10 (23.09) [7.04]

15 (34.63) [10.56]

20 (46.18) [14.08]

5 (11.54) [3.52]

10 (23.09) [7.04]

15 ( 34.63) [10.56]

20 (46.18) [14.08]

4.97 (11.48) [3.5]

14.21 (32.81) [10]

25.58 (59.06) [18]

Scan here to watch product video

OPTIONS

Intrinsically Safe Approval - Change model number from PBLT2 to PBLTX

Custom ranges or Cable Lengths - Contact the factory

ACCESSORIES

MTL5041, intrinsically safe galvanic isolator

MTL7706, intrinsically safe zener barrier

A-297, Dessicant Filter for vent tube. Removes humidity for

protection of the sensor. Changes color to show saturation

A-625, 316 SS Cable Hanger use with NPT option for attaching

chain for easy pulling out of application

Cable Type

ETFE

ETFE

ETFE

ETFE

Polyurethane

Polyurethane

Polyurethane

Polyurethane

Polyurethane

Polyurethane

Polyurethane

jeffmHighlight

jeffmHighlight

jeffmHighlight

jeffmHighlight

ES SERIES DOOR LOCKS AND HANDLES Industrial door locks - 880 SCQ4 series

These accessories include : Th 880 SCQ4 series door accessories were designed to fit Eurobex 'ES' style industrial enclosures. A full range of acces-sories are available to a.ccomo-date a variety of applications.

- 14 types of lock inserts (p.343) Locking mechanisms can be ordered as complete units or in parts. Parts include individual Inserts, cams and housings.

11:1.881

~ .791

u

- Key lock, padlock and combina-11on lock provisions (p.344) - Operating handles (p.344) - ~turn lock dust cap (p.345) ...

t 1.142

J

Available accessories, amongst others :

Lockln.erta p.843

'T' handl .. p.344

Key locks p.344

Wing handlu p.344

Combination locu p.344

Wing padlock p.344

Padlocks p.344

lntertor handle p.344

1.751

'L' handlu p.344

Duet cap p.346

The 880 SCQ4 acceaorlea are to be uaed with theee encloure .ertea, amongst othera :

5100 ES 6412 ES

5412 DDS 8412 5412 ESA

ES SERIES DOOR LOCKS AND HANDLES 'ES' style key locks, pad locks and combination locks

Key lock CATALOG # : KEY NUMBER : K8y Included? : M ... rtal: ForuHwllh :

llO~K K-1.1 ~ p1a11111.-1 ESri-.1412 EBA, 6412 ESDD. .

Padlock provisions CATALOG # : 880 PLES0375 KEY NUMBER: P9cllock K8y Included? : No Material : Stalnleu ateel For UH wllh : ES Mrt ... 8412

ESA, 6412 ESDD .

General purpose padlock CATAlDG # : 880 PL KEY NUMBER : UH padlock K8y Included? : No Mmertal : Plated steel For UM with : ES ri-, 8412

ESA, 5412 ESDD ...

Industrial door handles Key lock 'L' handle 1 point lock : 880 ~L a point lock : 1e& ESL2A KEY NUMBER: K-1.1 IC8y Included? : V.. Material : Zinc CUI For uH wllh : ES rt-. 1412

Key lock wing handle CATALOG # : 880 SCQ4.WN KEY NUMBER: KrWN IC8y Included? : V.. Material: Polyamlda GF/Zlnc For uH wllh : ES rt-. 1412

ESA, 6412 ESDD. ..

Wing knob CATALOG ti: KEY NUMBER : IC8y Included? : Material: Foruwllh :

l80 &CQt.WNH None NCI Polyamld GF/Zlnc ESrl-,1412 EBA, M12 ESDD .

Interior handle CATALOG ti : 880 SCQ4.DIH KEY NUMBER : Nona * C.nnm be uaed with by lock. Mnlrial : Red polyamld For u with : ES rt-. 9412

E&A, M12 ESDD ...

i

~ -

Combination lock CATALDG#: KEY NUMBER: K8y Included? : ....... : Foruwlth:

llOSCQ4-NL Non No Plllbld .... I ES Hrln, 1412 E8A, 6412 ESDD. ..

Weatherproof padlock 3/8" CATALOG# : 880 PDLK375 KEY NUMBER: K-1.1 K8y Included? : YH Matertal : BteelJPIMllc For u wllh : 880 PLESQ31

General purpo

Stainless steel padlock CATALOG# : B80 Pl.SS KEY NUMBER : U.. padlock K8y Included?: No M ... rial: Stlllnl ... lll:MI For UH wfth : ES urlea, 8412

ESA, 5412 ESDD .

Key lock 'r handle CATALDG # : 180 SCQ4.T KEY NUMBER: "-T K.-v Included? : ~ 11.mrtal : Palyamlde GFJ21nc For u with : ES Hrlea, 1412

E8A, 6412 ESDD. ..

Key lock straight handle CATALOG II : 880 SCQ4.8H KEY NUMBER : K.SH Kay lncludad? : V.. 11.mrtal : Polyamlde GiF/Zlnc For UH with : ES HrtH, 1412

ESA. &412 ESDD ...

Star handle CATALOG#: KEY NUMBER: Key Included? : M ... rial: For UH with :

llO SCQ4.STH Nona No Polyamlde GF/Zlnc ES ... lea, 8412 ESA, 15412 ESDD.-

Padlockable wing handle CATALOG# : KEY NUMBER : IC8y Included? : M"'9rtal: Foruwllh:

l80 8CQ4.WNP Padlock Na Polyamlde OF/Zinc ESri-.1412 ESA, IS412 ESDD .. ,

jeffmRectangle

C 1C 1

ElEctRonic/GlAss FUsEs

GGC/GGC-V GGM/GGM-V

1. 250VAC @ 35A I.R./125VAC @ 10kA I.R.2. 250VAC @ 200A I.R./125VAC @ 10kA I.R.3. 250VAC @ 10kA I.R.4. 125VAC @ 10kA I.R.5. 32VAC @ 1000A I.R.

1. 250VAC @ 35A I.R./125VAC @ 10kA I.R.2. 250VAC @ 100A I.R./125VAC @ 10kA I.R.3. 250VAC @ 200A I.R./125VAC @ 10kA I.R.4. 125VAC @ 10kA I.R.5. 250VAC @ 100A I.R.

Glass BodyFast Acting1/4 x 1-1/41-1/2 Axial Leads Optional

1/100A through 10A, 250VAC, UL Listed and CSA Certified12A and 15A, 125VAC, UL Listed and CSA Certified20A through 30A, 32VAC

GGC1/100GGC1/32GGC1/16GGC1/10GGC1/8GGC15/100GGC175/1000GGC3/16GGC2/10GGC1/4GGC3/10GGC3/8GGC4/10GGC1/2GGC6/10GGC3/4GGC8/10GGC1GGC1-1/4GGC1-1/2GGC1-3/4GGC1-6/10GGC2GGC2-1/4GGC2-1/2GGC3GGC3-2/10GGC4GGC5GGC6GGC6-3/10GGC7GGC7-1/2GGC8GGC10GGC12GGC15GGC20GGC25GGC30

250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V125V125V32V32V32V

1112222222222222222222222232222222244555

GGM1/16GGM1/10GGM1/8GGM2/10GGM1/4GGM3/10GGM4/10GGM1/2GGM6/10GGM7/10GGM3/4GGM8/10GGM1GGM1-2/10GGM1-1/4GGM1-1/2GGM1-6/10GGM2GGM2-1/2GGM3GGM4GGM5GGM6GGM7GGM8GGM10GGM15

1/16A1/10A1/8A

2/10A1/4A

3/10A4/10A1/2A

6/10A7/10A3/4A

8/10A1A

1-2/10A1-1/4A1-1/2A1-6/10A

2A2-1/2A

3A4A5A6A7A8A

10A15A

250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V250V125V125V125V125V125V250V250V

233333131331323323334444455

GGC-V1/100GGC-V1/32GGC-V1/16GGC-V1/10GGC-V1/8

GGC-V15/100GGC-V175/1000

GGC-V3/16GGC-V2/10GGC-V1/4

GGC-V3/10GGC-V3/8

GGC-V4/10GGC-V1/2

GGC-V6/10GGC-V3/4

GGC-V8/10GGC-V1

GGC-V1-1/4GGC-V1-1/2GGC-V1-3/4

GGC-V1-6/10GGC-V2

GGC-V2-1/4GGC-V2-1/2

GGC-V3GGC-V3-2/10

GGC-V4GGC-V5GGC-V6

GGC-V6-3/10GGC-V7

N/AGGC-V8

GGC-V10GGC-V12GGC-V15GGC-V20GGC-V25GGC-V30

1/100A1/32A1/16A1/10A1/8A

15/100A175/1000A

3/16A2/10A1/4A

3/10A3/8A

4/10A1/2A

6/10A3/4A

8/10A1A

1-1/4A1-1/2A1-3/4A

1-6/10A2A

2-1/4A2-1/2A

3A3-2/10A

4A5A6A

6-3/10A7A

7-1/2A8A

10A12A15A20A25A30A

GGM-V1/16GGM-V1/10GGM-V1/8

GGM-V2/10GGM-V1/4



GGM-V8/10GGM-V1

N/AGGM-V1-1/4GGM-V1-1/2

GGM-V1-6/10GGM-V2

GGM-V2-1/2GGM-V3GGM-V4GGM-V5GGM-V6GGM-V7GGM-V8

GGM-V10GGM-V15

StandardFuseAmpereRatings

StandardFuseAmpereRatings

Glass BodyFast Acting5mm x 20mm1-1/2 Axial Leads Optional

1/16A through 3A, 250VAC, UL Listed and CSA Certified4A through 8A, 125VAC, UL Listed and CSA Certified10A and 15A, 250VAC, UL Recognized

CATALOG AXIALLEAD AMPERE VOLTS I.R.NUMBER CAT.NO RATINGCATALOG AXIALLEAD AMPERE VOLTS I.R.NUMBER CAT.NO RATING

Gross Automation (877) 268-3700 www.ferrazshawmutsales.com [email protected]

jeffmHighlight

jeffmHighlight

jeffmHighlight

jeffmHighlight

jeffmHighlight

All dimensions in inches

50/60 HertzPrimary Voltage: 240 x 480 230 x 460 220 x 440Secondary Voltage: 120 x 240 115 x 230 110 x 220

All dimensions in inches

50/60 HertzPrimary Voltage: 240 x 480 230 x 460 220 x 440Secondary Voltage: 12 x 24 11.5 x 23 11 x 22

Primary and Secondary voltage links/jumpers supplied standard with all transformers.Special voltages and VA sizes available upon request.* See page 10 for dimensional drawings.

Primary and Secondary voltage links/jumpers supplied standard with all transformers.Special voltages and VA sizes available upon request. 1 Note For 750 through 2000 VA units actual overall depth is 0.24 plus the value in column B.* See page 10 for dimensional drawings.

VARating

CE VA Rating

CatalogNumber

Mtg.Fig.

OutputAmps

OverallDimensions

MountingCenters

MountingSlot Height with

Finger Guard

Height with Fuse Block

Adapter

Approx.Ship

WeightLbs.A B C D E G X H

50 50 SP50MQMJ A 0.42/0.21 2.60 3.35 2.60 2.13 2.17 0.22 x 0.44 2.98 2.79 1.7100 100 SP100MQMJ A 0.83/0.42 2.99 3.74 2.85 2.52 2.60 0.22 x 0.44 3.23 3.04 3150 150 SP150MQMJ A 1.25/0.63 2.99 4.29 2.85 2.52 3.15 0.22 x 0.44 3.23 3.04 4.3250 160 SP250MQMJ A 2.08/1.04 3.78 4.09 3.40 3.31 2.99 0.22 x 0.44 3.78 3.59 6.5350 250 SP350MQMJ A 2.92/1.46 3.78 4.69 3.40 3.31 3.58 0.22 x 0.44 3.78 3.59 8.2500 300 SP500MQMJ A 4.17/2.08 4.49 4.69 3.78 3.78 3.66 0.31 x 0.81 4.16 3.97 11750 500 SP750MQMJ A 6.25/3.13 5.25 4.691 4.37 4.50 3.66 0.31 x 0.81 4.75 4.56 16

1000 650 SP1000MQMJ A 8.33/4.17 5.25 5.471 4.37 4.50 4.45 0.31 x 0.81 4.75 4.56 211500 1000 SP1500MQMJ A 12.5/6.25 5.25 6.851 4.37 4.50 5.83 0.31 x 0.81 4.75 4.56 282000 1300 SP2000MQMJ A 16.7/8.33 6.38 5.871 5.31 5.75 4.84 0.31 x 0.81 5.50 5.31 353000 2000 SP3000MQMJ A 25.0/12.5 7.50 7.50 6.50 6.30 7.28 0.44 x 1.00 6.50 6.50 645000 3000 SP5000MQMJ C 41.7/20.8 8.98 9.88 7.76 7.40 7.28 0.44 x 1.00 N/A N/A 97

VARating

CE VA Rating

CatalogNumber

Mtg.Fig.

OutputAmps

OverallDimensions

MountingCenters

MountingSlot Height with

Finger Guard

Height with Fuse Block

Adapter

Approx.Ship

WeightLbs.A B C D E G X H

50 50 SP50QR A 4.17/2.08 2.60 3.35 2.60 2.13 2.17 0.22 x 0.44 2.98 2.79 1.7100 100 SP100QR A 8.33/4.17 2.99 3.54 2.85 2.52 2.40 0.22 x 0.44 3.23 3.04 3150 150 SP150QR A 12.5/6.25 2.99 4.29 2.85 2.52 3.15 0.22 x 0.44 3.23 3.04 4.3250 160 SP250QR A 20.8/10.4 3.78 4.09 3.40 3.31 2.99 0.22 x 0.44 3.78 3.59 6.5350 250 SP350QR A 29.2/14.6 3.78 4.69 3.40 3.31 3.58 0.22 x 0.44 3.78 3.59 8.3500 300 SP500QR B 41.7/20.8 4.49 5.47 3.78 3.78 3.66 0.31 x 0.81 4.16 3.97 11

Visit our website: www.hammondpowersolutions.comPage 10

E

B

AD

CG x H

AD E

C

G x H

B

dimensional drawings

FIGURE B FIGURE A

AD E

CG x H

B

B

FIGURE C

Some actual transformer units may differ from dimensional drawings shown below.

Floor-Mount EnclosurEs Type 12 Floor-MounT enclosures

Spec-00295 KEQUIPMENT PROTECTIONSUBJECT TO CHANGE WITHOUT NOTICEMild stEEl1

SPEC-00295K763.422.2211763.422.2600

Mild stEElFLOOR-MOUNT ENCLOSURESTYPE 12 FLOOR-MOUNT ENCLOSURES

tWo-door WitH Floor stAnds, tYPE 12

industrY stAndArds

UL 508A Listed; Type 12; File No. E61997cUL Listed per CSA C22.2 No. 94; Type 12; File No. E61997

NEMA/EEMAC Type 12CSA, File No. 42186, Type 12IEC 60529, IP55

APPlicAtionEnclosures have gasketed, overlapping doors to keep the elements at bay and floor stands that provide additional height and access for cleaning under the enclosure. Because there is no centerpost, it is simple to install and remove panels.

sPEciFicAtions Seams continuously welded and ground smooth; no holes or

knockouts Gasketed overlapping doors with no centerpost 3-point latch mechanism operated by oil-tight key-lock handle Concealed, easy-to-remove hinges Data pocket is high-impact thermoplastic 12-in. floor stands welded to enclosure Heavy-duty lifting eyes Panel supports Oil-resistant gasket Collar studs for mounting optional panel Bonding provision on door Provision for mounting fluorescent light

FinisHTwo finishes available: ANSI 61 gray, polyester powder paint outside and inside; or ANSI 61 gray outside and white, polyester powder paint inside. Optional panels available with a white or conductive finish.

AccEssoriEsBlower Fan PackageDrip Shield Kit for Type 12 EnclosuresINTERSAFE Data Interface Ports, Type 4/4X/12PANELITE Enclosure LightsHole SealsWindow KitsSee also the Popular Cooling Products and Accessories tables following the Standard Product table

ModiFicAtion And custoMiZAtionHoffman excels at modifying and customizing products to your specifications. Contact your local Hoffman sales office or distributor for complete information.BULLETIN: A12L

Standard Product

Catalog Number AxBxC in. AxBxC mmInteriorFinish Gauge Panel

ConductivePanel

PanelGauge Panel Size (in.) Panel Size (mm)

Stiffener(in.)

Stiffener(mm) S (in.) S (mm)

A544208LPG 54.00 x 42.00 x 8.00 1372 x 1067 x 203 Gray 12 A54P42 A54P42G 12 50.00 x 38.00 1270 x 965 15.00 381 A544208LP 54.00 x 42.00 x 8.00 1372 x 1067 x 203 White 12 A54P42 A54P42G 12 50.00 x 38.00 1270 x 965 15.00 381 A604808LPG 60.06 x 48.06 x 8.06 1526 x 1221 x 205 Gray 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A604808LP 60.06 x 48.06 x 8.06 1526 x 1221 x 205 White 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A604810LPG 60.06 x 48.06 x 10.06 1526 x 1221 x 256 Gray 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A604810LP 60.06 x 48.06 x 10.06 1526 x 1221 x 256 White 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A606010LPG 60.06 x 60.06 x 10.06 1526 x 1526 x 256 Gray 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A606010LP 60.06 x 60.06 x 10.06 1526 x 1526 x 256 White 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A726010ULPG 72.06 x 60.06 x 10.06 1830 x 1526 x 256 Gray 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A726010ULP 72.06 x 60.06 x 10.06 1830 x 1526 x 256 White 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A727210ULPG 72.06 x 72.06 x 10.06 1830 x 1830 x 256 Gray 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A727210ULP 72.06 x 72.06 x 10.06 1830 x 1830 x 256 White 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A604812LPG 60.06 x 48.06 x 12.06 1526 x 1221 x 306 Gray 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A604812LP 60.06 x 48.06 x 12.06 1526 x 1221 x 306 White 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A606012LPG 60.06 x 60.06 x 12.06 1526 x 1526 x 306 Gray 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A606012LP 60.06 x 60.06 x 12.06 1526 x 1526 x 306 White 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A726012ULPG 72.06 x 60.06 x 12.06 1830 x 1526 x 306 Gray 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A726012ULP 72.06 x 60.06 x 12.06 1830 x 1526 x 306 White 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A727212ULPG 72.06 x 72.06 x 12.06 1830 x 1830 x 306 Gray 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A727212ULP 72.06 x 72.06 x 12.06 1830 x 1830 x 306 White 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A604816LPG 60.06 x 48.06 x 16.06 1526 x 1221 x 408 Gray 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A604816LP 60.06 x 48.06 x 16.06 1526 x 1221 x 408 White 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A606016LPG 60.06 x 60.06 x 16.06 1526 x 1526 x 408 Gray 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A606016LP 60.06 x 60.06 x 16.06 1526 x 1526 x 408 White 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A726016ULPG 72.06 x 60.06 x 16.06 1830 x 1526 x 408 Gray 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A726016ULP 72.06 x 60.06 x 16.06 1830 x 1526 x 408 White 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506

Floor-Mount EnclosurEs Type 12 Floor-MounT enclosures

Spec-00295 KPH 763.422.2211 FAX 763.422.2600 PENTAIRPROTECT.COMEQUIPMENT PROTECTION Mild stEEl 2

Catalog Number AxBxC in. AxBxC mmInteriorFinish Gauge Panel

ConductivePanel

PanelGauge Panel Size (in.) Panel Size (mm)

Stiffener(in.)

Stiffener(mm) S (in.) S (mm)

A727216ULPG 72.06 x 72.06 x 16.06 1830 x 1830 x 408 Gray 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A727216ULP 72.06 x 72.06 x 16.06 1830 x 1830 x 408 White 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A604820LPG 60.06 x 48.06 x 20.06 1526 x 1221 x 510 Gray 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A604820LP 60.06 x 48.06 x 20.06 1526 x 1221 x 510 White 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A726020ULPG 72.06 x 60.06 x 20.06 1830 x 1526 x 510 Gray 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A726020ULP 72.06 x 60.06 x 20.06 1830 x 1526 x 510 White 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A727220ULPG 72.06 x 72.06 x 20.06 1830 x 1830 x 510 Gray 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A727220ULP 72.06 x 72.06 x 20.06 1830 x 1830 x 510 White 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A604824LPG 60.06 x 48.06 x 24.06 1526 x 1221 x 611 Gray 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A604824LP 60.06 x 48.06 x 24.06 1526 x 1221 x 611 White 12 A60P48 A60P48G 10 56.00 x 44.00 1422 x 1118 15.00 381 15.92 404A606024LPG 60.06 x 60.06 x 24.06 1526 x 1526 x 611 Gray 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A606024LP 60.06 x 60.06 x 24.06 1526 x 1526 x 611 White 12 A60P60 A60P60G 10 56.00 x 56.00 1422 x 1422 21.00 533 19.92 506A726024ULPG 72.06 x 60.06 x 24.06 1830 x 1526 x 611 Gray 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A726024ULP 72.06 x 60.06 x 24.06 1830 x 1526 x 611 White 12 A72P60 A72P60G 10 68.00 x 56.00 1727 x 1422 21.00 533 19.92 506A727224ULPG 72.06 x 72.06 x 24.06 1830 x 1830 x 611 Gray 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608A727224ULP 72.06 x 72.06 x 24.06 1830 x 1830 x 611 White 12 A72P72 A72P72G 10 68.00 x 68.00 1727 x 1727 24.00 610 23.92 608Purchase panels separately.

$

&

$

% < <

$ % 6 6

Spec-00310 P

Panels and Panel accessories Panels for enclosures

EQUIPMENT PROTECTIONSUBJECT TO CHANGE WITHOUT NOTICEaccessories7

Panels for tyPe 3r, 4, 4x, 12 and 13 enclosuresSteel panels are 12 gauge, finished with white polyester powder paint or a conductive, corrosion-resistant coating. Larger panels have flanges on two or four sides. Some larger steel panels are 10 gauge and include extra holes for panel lifting. Aluminum panels are 5052-H32 aluminum alloy. Larger panels have flanges on four sides. Aluminum panels are protected on one side with a plastic film. Stainless steel panels are Type 316 stainless steel. Panel mounting hardware is furnished with all enclosures which accept these panels.Bulletin: pnlFS, pnlJ, pnlWM

Catalog Number MaterialPanel SizeD x E (in.)

Panel SizeD x E (mm)

Panel Gaugeor Thickness

EdgeFlanges T (in.) T (mm)

Numberof Holes

A12P24 Painted steel 9.00 x 21.00 229 x 533 12 ga. 0 4A12P24G Conductive steel 9.00 x 21.00 229 x 533 12 ga. 0 4A16P12 Painted steel 13.00 x 9.00 330 x 229 12 ga. 0 4A16P12G Conductive steel 13.00 x 9.00 330 x 229 12 ga. 0 4A16P12SS6 Stainless Steel 13.00 x 9.00 330 x 229 12 ga. 0 4A16P12AL Aluminum 13.00 x 9.00 330 x 229 0.10 in./3 mm 0 4A16P16 Painted steel 13.00 x 13.00 330 x 330 12 ga. 0 4A16P16G Conductive steel 13.00 x 13.00 330 x 330 12 ga. 0 4A16P16SS6 Stainless Steel 13.00 x 13.00 330 x 330 12 ga. 0 4A16P16AL Aluminum 13.00 x 13.00 330 x 330 0.10 in./3 mm 0 4A18P18 Painted steel 15.00 x 15.00 381 x 381 12 ga. 0 4A18P18G Conductive steel 15.00 x 15.00 381 x 381 12 ga. 0 4A20P12 Painted steel 17.00 x 9.00 432

harris ridge condos panel submittal rev a

Documents

va control transformers

submersible nonclog

motor power circuits

origi july27

plate exterior door

motor contactors

exterior doors

motor starter nema