heating and cooling...heating mode natural gas room heating condenser gas engine compressor waste...
TRANSCRIPT
GAS ENGINE HEAT PUMPHEATING AND COOLING
Renewable energy for industry and commerce
Everything like always – just different Motor-driven heat pumps basically work on the same principle: heat is extracted from a medium and made available at a higher temperature level via the heat pump cycle. The central element here is the compressor.
Gas engine heat pumps use an environmentally friendly gas engine to drive the compressor. Here, the low primary energy factor of gas has a positive effect on the EnEV valuation (German Energy Saving Regulations).
During the operation of the gas engine heat pump, hardly any conversion losses and only small distribution losses occur. The high efficiency - combined with low primary energy costs (gas versus electricity) - significantly reduces operating costs and enables extremely short payback periods.
Flexible heating and cooling The following possibilities result from only one system:
• heating• cooling• hot water from engine waste heat • combined heat and power by using the cooling
circuit of the engine
This complete system is both economically and ecologically convincing.
THE OPTIMAL SOLUTION FOR HIGH DEMANDS The gas engine heat pump of AISIN Toyota is one of the most efficient components of our product portfolio. Cosy warmth in the winter and pleasant cooling in the summer – the gas engine heat pump combines both functions in one device. The decentralized and directly operated system enables considerable economic benefits while simultaneously protecting our environment.
With a gas engine heat pump energy
is drawn from the fuel and the
environment. A gas engine heat pump
can substantially cover the daily
energy requirements in the heating
as well as in the cooling operation
by free environmental heat from
the ambient air.
thermal heat
condensernatural gas
gas engine
using engine heat
Kompressor
ambient energy
evaporator
exp
ansi
on
valv
e
Heating mode
natural gas
room heating
condenser
gas engine
compressor
waste heat
evaporator
exp
ansi
on
valv
e
Cooling mode
using engine heat at 70 ° C
The AISIN Toyota gas engine heat pump is univer-sally applicable: whether direct expansion in the refrigeration circuit or connection to buffer storage tanks and systems. Cascades are possible for larger powers. From planning to installation,
you receive all the components and services for your system from a single source. The high state subsidies for the AISIN Toyota gas engine heat pump are also an interesting fact. We would be glad to inform you about the possibilities.
easy to maintain
considerable savings of operational costs
low installation costs
easy to handle
combinable with other GoGaS-systems
heating and cooling with one device
Fulfillment of EnEV (German Energy Saving
Regulations) and EEWärmeG (German
Renewable Energy Law)
low CO2-emissions
All benefits at a glance
Components and options
using engine heat at 70 ° C
YOSHI® Hydraulic module for integration of GMHP in
hydraulic networks
dire
ct e
xpan
sion
w
ith
R41
0a
flow
tem
pera
ture
hea
ting
50
°C
flow
tem
pera
ture
coo
ling
7 °C
ventilation
ventilation buffer storagewarm air heater
ceiling cassette channel unit
Stan
d: 1
0/2
018
YOSHI® Hydraulic module
Model AWS-8HP-F1
AWS-10HP-F1
AWS-13HP-F1
AWS-16HP-F1
AWS-20HP-F1
AWS-25HP-F1
AWS-30HP-F1
connectable GEHP AXGP224E1 AXGP280E1 AXGP355E1 AWGP450F1 AWGP560F1 AWGP710F1 AWGP850F1
rated cooling capacity kW 21,0 26,5 33,5 42,5 53,0 63,5 74,5
rated cooling consumption (GEHP) kW 15,3 20,0 27,7 30,0 43,0 56,0 70,7
GUE cooling - 1,37 1,33 1,21 1,42 1,23 1,13 1,05
SPER cooling - 1,72 1,72 1,93 1,89 1,89 1,87 1,91
rated heating capacity kW 23,5 30,0 37,5 50,0 62,5 77,0 87,5
rated heating consumption (GEHP) kW 15,5 20,2 27,0 34,0 42,5 54,2 61,5
GUE heating - 1,52 1,48 1,39 1,47 1,47 1,42 1,42
SPER heating - 1,37 1,36 1,35 1,57 1,55 1,54 1,51
Maximum engine heat recovery kW 8,0 10,0 13,5 19,5 23,5 30,5 44,5
maximum water temperature out °C 47 50
Minimum water temperature out °C 7
dimensions (HxWxD) mm 915 x 710 x 1.020
weight (standard/without pump) kg 164/153 204/177 207/180
Gas engine heat pump
Model AXGP224E1 AXGP280E1 AXGP355E1 AWGP450F1 AWGP560F1 AWGP710F1 AWGP850F1
rated cooling capacity kW 22,4 28,0 35,5 45,0 56,0 71,0 85,0
rated cooling consumption kW 15,0 19,2 26,4 31,4 38,9 54,4 71,2
GUE cooling - 1,49 1,46 1,34 1,43 1,44 1,31 1,19
SPER cooling - 2,01 2,14 2,17 2,39 2,44 2,42 2,17
rated heating capacity kW 25,0 31,5 40,0 50,0 63,0 80,0 95,0
rated heating consumption kW 15,9 20,3 27,0 29,8 38,1 53,9 68,0
GUE heating - 1,57 1,55 1,48 1,68 1,65 1,48 1,40
SPER heating - 1,31 1,32 1,34 1,48 1,55 1,54 1,52
maximum engine heat recovery kW 8,0 10,0 13,5 15,7 19,5 27,2 35,6
dimensions (HxWxD) mm 2.077 x 1.440 x 880 2.245 x 1.660 x 880
weight kg 565 765 795 870
scheduled maintenance interval h 10.000
scheduled engine oil replacement h 30.000
GoGaS Goch GmbH & Co. KG Zum Ihnedieck 1844265 Dortmund Germany
Phone +49 231 46505-0Fax +49 231 46505-88 [email protected]