häfele lever handles...5. drill bit × 3 [ø 8, ø10 & ø12 mm] 3 the drilling jig for top and...

ww

w.h

afel

eind

ia.c

om

ww

w.h

afel

eind

ia.c

om

TARGET Connectors

Häfele brings to you TARGET, a new structural connecting fitting conceived by Italiana Ferramenta with high fastening capacity, suitable for mounting with wood dowels.

With the new connecting fitting, assembly is now possible in extremely narrow gaps which makes TARGET especially practical when working inside a niche.

Wide Range of Application Practical solution for installation of wardrobes, bookcases, modular furniture & office furniture

Easy Pre-assembling Simple pre-insertion into furniture either through automatic machinery or by hand

Suitable for Furniture Kits Can be easily pre-mounted on the panel without interfering with the packaging, eliminating the need for fitting bags

Strong Structural Fastening Panels are securely fastened with the new connectors, making the cabinet 100% stress-resistant

No Hardware Kits No additional screws, nuts and miscellaneous hardware accessories are required for assembly

High Speed Assembling Mounting & assembly is extremely easy. Just slide in the panels (pre-installed with the connectors) and tighten the pinion screw for a firm connection.

Häfele brings to you TARGET, a new structural connecting fitting conceived by Italiana Ferramenta with high fastening capacity, suitable for mounting with wood dowels.

With the new connecting fitting, assembly is now possible in extremely narrow gaps which makes TARGET especially practical when working inside a niche. Wide Range of Application

Strong Structural Fastening

TARGET CONNECTORS J10 & J12

Art. No. L L1 030.10.862 13 15

030.10.565 17 19

030.10.868 10 12

High Speed Assembly Direct Access to Levellers

Material: Zinc Alloy, Steel (Zinc Plated) & Plastic

For panels with a thickness of 18 -19 mm

Material: Steel (Zinc Plated)

For panels with a min. thickness of 25 mm

Material: Raw Zinc Alloy

L L1 17 19

L L1 10 12 13 15

The 10mm diameter pinion screw of the Connector is barely visible on the panel making TARGET J10 a minimalistic solution with captivating aesthetical looks

Suitable for Furniture Kits


Please Note: L = Length of the insert nut; L1 = Length drilled in the side panel to fit in the insert nut

Material: Plastic ; Colour: White

Round Rectangular

This cover cap conceals the 10mm diameter hole drilled to mask the pinion screw. Use this cover cap on overhead units or on the top panels of units with weight bearing bottoms like freestanding cabinets / cupboards.

This cover cap conceals both the 12 mm diameter hole drilled in order to adjust the leveller and the 10mm diameter hole drilled to mask the pinion screw. This cover cap is particularly used on units with weight bearing bottoms like freestanding cabinets / cupboards where the connector is attached to the leveller.

Insert the TARGET J10 connector with the countersunk hole on top.

Place the pinion screw from above.

Press strongly with a cross screwdriver to slot the pinion screw in.

It may be helpful to use a tool in order to easily slot the pinion screw in.

By turning the pinion screw, the threaded dowel makes a synchronized rotation.

Cordless Driver drill to be used only with the friction mode on.


Art. No. L L1 030.10.862 13 15

030.10.565 17 19

030.10.868 10 12

High Speed Assembly Direct Access to Levellers

Material: Zinc Alloy, Steel (Zinc Plated) & Plastic

For panels with a thickness of 18 -19 mm

Material: Steel (Zinc Plated)

For panels with a min. thickness of 25 mm

Material: Raw Zinc Alloy

L L1 17 19

L L1 10 12 11 13

The passing-through hole on the pinion screw of the TARGET J12 Connector gives direct access to the adjustable feet (leveller) without drilling extra holes.

Suitable for Furniture Kits


Please Note: L = Length of the insert nut; L1 = Length drilled in the side panel to fit in the insert nut

Material: Plastic ; Colour: White

Round Rectangular

This cover cap conceals the 12mm diameter hole drilled to mask the pinion screw.

This cover cap conceals both the 12 mm diameter hole drilled in order to adjust the leveller and the 10mm diameter hole drilled to mask the pinion screw. This cover cap is particularly used on units with weight bearing bottoms like freestanding cabinets / cupboards where the connector is attached to the leveller.

Insert the TARGET J12 connector with the countersunk hole on top.

Place the pinion screw from above.

Press strongly with a cross screwdriver to slot the pinion screw in.

It may be helpful to use a tool in order to easily slot the pinion screw in.

By turning the pinion screw, the threaded dowel makes a synchronized rotation.

Cordless Driver drill to be used only with the friction mode on.


TARGET J12

TARGET J10

1 2

5

The Drilling Jig Set for TARGET J10 & J12 consists of:

1. Drilling Jig for Top and Bottom Panels with Drilling Guide Bushes × 1

2. Drilling Jig for Side Panels with Drilling Guide Bushes × 1

3. Stop Collars × 3 [ø 8, ø10 & ø12 mm]

4. Spacers × 4 [1 mm (1) & 1.5 mm (3)]

5. Drill Bit × 3 [ø 8, ø10 & ø12 mm] 4

3

The Drilling Jig for Top and Bottom Panels is set on default to drill panels with a thickness of 16 mm. If you want to for example, drill a panel with a thickness of 18 mm, then you need to add a 1 mm spacer in between the jig as shown in the above diagram and 3 spacers of 1.5 mm each for a panel with a thickness of 25 mm.

The Drilling Jig for Top and Bottom Panels comes with 5 Drilling Guide Bushes (ø8 mm × 2, ø10 mm × 2 & ø12 mm × 1)


TARGET J12

ACCORDING TO BOTTOM

& TOP POSITIONING

The Drilling Jig for Side Panels comes with 3 Drilling Guide Bushes (ø8 mm × 3)

FOR INTERNAL

PARTITIONS

B=A-25

B=A-25

A

A A


Please Note: L = Thickness of the spacer Please Note: L = Length of the Drill Bits

Article No. Description Unit MRP (INR) TARGET J10 262.11.020 TARGET J10 Connector Pc 63/- 262.11.051 TARGET J10 Pinion Screw for panels with a thickness of 18 -19 mm Pc 27/- 262.11.052 TARGET J10 Pinion Screw for panels with min. thickness of 25 mm Pc 35/- 030.10.862 Insert Nut (M6 × 10 × 13) Pc 6/- 030.10.565 Insert Nut (M6 × 10 × 17) Pc 8/- 030.10.868 Insert Nut (M6 × 10 × 10) Pc 8/- 262.11.036 Cover Cap - Round Pc 3/- 262.11.035 Cover Cap - Rectangular Pc 3/- TARGET J12 262.11.021 TARGET J12 Connector Pc 63/- 262.11.027 TARGET J12 Pinion Screw for panels with a thickness of 18 -19 mm Pc 27/- 262.11.029 TARGET J12 Pinion Screw for panels with min. thickness of 25 mm Pc 35/- 030.10.862 Insert Nut (M6 × 10 × 13) Pc 6/- 030.10.565 Insert Nut (M6 × 10 × 17) Pc 8/- 030.10.868 Insert Nut (M6 × 10 × 10) Pc 8/- 262.11.037 Cover Cap - Round Pc 3/- 262.11.040 Allen Key for TARGET J12 Pinion Screw Pc 67/- DRILLING JIG 001.15.160 Drilling Jig Kit for TARGET J10 & J12 Kit 39,260/-


häfele lever handles...5. drill bit × 3 [ø 8, ø10 & ø12 mm] 3 the drilling jig for top and...

Documents