häfele lever handles...new extendable table fittings 2 extendable table fittings by häfele...

Product Info w

ww

.haf

elei

ndia

.com

EXTENDABLE TABLE FITTINGS

2 New Extendable Table Fittings

Extendable Table Fittings by Häfele

Intuitive furniture is the need of the hour. In times like these where every extra square meter is considered as good as gold, installing versatile home interiors becomes crucial.

You will be surprised at the amount of functionality that can be brought in by some intelligent furniture fittings. Häfele brings to you its spontaneous range of Extendable Table Fittings that grants you the liberty to design your dream abode as envisaged and in fact helps create more space. These fittings simply blend into your interiors when closed but once released they end up making quite a statement.

Häfele’s range of extendable table fittings consists of : • LUNCH, a small two leaf table top fitting that can be used as a study table in rooms, as a dining

table or as an extension to the kitchen worktops in small kitchens and kitchenettes etc.

• PARTY MENSOLA, a comparatively larger sized, four leaf, table top fitting with a higher weight carrying capacity. It is ideal for use as dining tables in kitchens, as desks in offices etc.

This product communication takes you through the following details :

TOPIC PAGE NO.

LUNCH 3 – 9

• Product Specifications 6

• Technical Specifications 7

• Installation Specifications 8-9

PARTY MENSOLA 10 – 20

• Product Specifications 13

• Technical Specifications 14

• Installation Specifications 15-20

ORDERING INFORMATION 21


This space-saving system consists of a pull-out tabletop fitting stored in a space normally used for a drawer. The table fitting pulls out instantly by simply opening the hinged front of the drawer space. Created to cater to the needs of functionality in small spaces, this runner is ideal for small kitchens and kitchenettes needing a tabletop for breakfast or simply as an extension of the worktop for preparing meals.


PRODUCT SPECIFICATIONS

LUNCH : 505.73.944

Number of planes : 2

Weight carrying capacity : 60 Kgs. (evenly distributed)

Material (sliding guides) : Natural Anodised Aluminium

Finish : Stainless Steel

Dimensions : 600 mm (width) × 969 mm (length)

Closed Slides Opening Plane Tilting

Opened

Push the red locking lever to close the mechanism

Functioning Steps :


TECHNICAL SPECIFICATIONS

LUNCH : 505.73.944

(A)

(B)

(C)

(D) (E

)

(F)

(P)

Note: Side Thickness of panels can vary from 15- 20 mm. The table demonstrated above shows you measurements of 3 commonly used side thicknesses.

Specifications Side Panel Thickness (L)

L = 15 mm L = 18 mm L = 20 mm

Overall width (A) : 570 mm 564 mm 560 mm

Space between the slides (B) : 436 mm 430 mm 426 mm

Handle length (C) = A – 158 412 mm 406 mm 402 mm

Distance between fixing plane holes (D) = A – 82 488 mm 482 mm 478 mm

Length of sliding guides : 789 mm 789 mm 789 mm

Plane Thickness (S) : 18 mm 18 mm 18 mm

Width of the planes (P) = L – [[S × 2] + 3] 567 mm 561 mm 557 mm

Min. vertical free space requirement (E) = 62 + [S × 2] 98 mm 98 mm 98 mm

Min. internal free space requirement (F) : 540 mm 540 mm 540 mm


INSTALLATION SPECIFICATIONS

LUNCH : 505.73.944

Drilling measurements for external slide

Mounting the mechanism onto the cabinet

When this product is delivered to you, the sliding guides come attached as a single mechanism. Hence, in order to mount the mechanism onto the cabinet, it is necessary to first disassemble the two external slides from the rest of the mechanism. To do this, you need to unscrew the two screws in the rear of the second profile. You can now fix the external slides onto the cabinet sides using the included screws (M6×12). Lastly, insert or slide in the mechanism on the mounted external slides and tighten the two screws (one on each side of the second profile). Finally you must screw under the front part of each external slide with (M5x6) screws for additional stability.

You need to drill four holes (ø 8 × 13 mm) on each cabinet side for installing the brass bushes.

Brass bushes (included in the pack) Dimension: (ø 8 × 12 mm)

Screw (M6 x12)

Screw (M5 x 6)



LUNCH : 505.73.944

Plane dimensions


Screw (M6 x 60)

To install the fixed plane onto the sliding guides, you need to first drill four holes (ø 8 × 13 mm) under the fixed plane for fitting in the brass bushes. The fixed plane can then be mounted by inserting the screws (M6 × 60) properly into the holes on the central slide.

Note: This system can either be mounted in a cabinet of a base unit or can be mounted in a cabinet that is suspended by the help of wall hanging brackets. In case you wish to suspend the cabinet, you will have to order the wall hanging brackets separately


This new transformable system is designed and engineered down to the smallest detail. It can be mounted in a standard drawer compartment without the need for special fittings, guaranteeing a large-sized (up to approx. 1600 mm) and high capacity (100 Kg equally distributed) table fitting with an integrated telescopic leg.


PRODUCT SPECIFICATIONS

PARTY MENSOLA : 642.19.935

Number of planes : 4

Weight carrying capacity : 100 Kgs. (evenly distributed)

Material (sliding guides) : Natural Anodised Aluminium

Finish : Stainless Steel

Dimensions : 900 mm (width) × 1794 mm (length)

Functioning Steps :

Closed Slides Opening Turning & Extending the Leg

1. Turn the lever as indicated

2. The leg is now free to rotate

3. Turn the lever as indicated

4. Pull out the lower part of the leg until you hear a click from the blocking button

A

A

Placing the Three Free Top Panels Opened

B

B Push the red locking lever to close the mechanism


TECHNICAL SPECIFICATIONS


Specifications Side Panel Thickness

15 mm 18 mm 20 mm

Overall width (A) : 858 mm 864 mm 868 mm

Minimum Cabinet Depth (B) : 502 mm 502 mm 502 mm

Minimum Cabinet Height (C) : 155 mm 155 mm 155 mm

Width of the Planes (D) : 826 mm 832 mm 836 mm

Complete Top Length (E) : 1794 mm 1794 mm 1794 mm

Total Length Outside the Cabinet (F) : 1562 mm 1562 mm 1562 mm

Table Top Height (G) : 733 mm 733 mm 733 mm

Plane Thickness (S) : 18 mm 18 mm 18 mm

Min. vertical free space requirement (H) = 80 + [S × 4] 152 mm 152 mm 152 mm

Note: Side Thickness of panels can vary from 15- 20 mm. The table demonstrated above shows you measurements of 3 commonly used side thicknesses.

(B)

(A)

(C)

(D)

(E)

(F)

(B)

(G)



Drilling measurements for slide installation


You need to drill four holes (ø 8 × 13 mm) on each cabinet side for installing the brass bushes.

Attaching the leg to the sliding guide

TPS Screw (M6 x16)

Screw (M6 x 12)

Before installing the mechanism into the cabinet, you need to fix the extendable leg onto the sliding guide.




Separating the external guide from the mechanism

When this product is delivered to you, the sliding guides come attached as a single mechanism. Hence, in order to mount the mechanism onto the cabinet, it is necessary to first disassemble the two external slides from the rest of the mechanism. To do this follow the below mentioned steps.

Fixing the lateral bar and external slide to the cabinet sides


2. Unscrew the two screws in the rear of the first central profile.

Lateral Bar

External Slide Screw (M6 x 12)

In order to mount the mechanism onto the cabinet, you will first have to fix the Lateral Bar to the internal cabinet sides using an Allen key and 4 screws (M6×12). Using the same Allen key, fix the external slide to the lateral by with another 4 screws (M6×12).

1. Unscrew the two screws under the external slide



Mounting the mechanism onto the cabinet


Slide in the mechanism on the mounted external slides. Tighten the screw on each side when the end of the first central slide is about 250 mm from the back of the external slide. Once that is done tighten the two screws under the external slide.

2. Tighten the two screws under the external slide

1. Tighten the two screws in the rear of the first central profile.

Assembly of the top fixed plane


Screw (M6 x 60)

To install the fixed plane onto the sliding guides, you need to first drill four holes (ø 8 × 13 mm) under the fixed plane for fitting in the brass bushes. The fixed plane is then ready to be mounted on the sliding guides by inserting the four screws (M6 × 60) properly into the holes on the central slide. Before you assemble the fixed plane onto the sliding guide, you need to also drill three holes (as per the dimensions mentioned below) on the front side of the fixed plane (the side that will face the central plane) in order to insert the female centering pins.

Female Pin

350 mm 350 mm X X

Side Panel Thickness 15 mm 18 mm 20 mm

Distance from the edge (X) 63 mm 66 mm 68 mm



Assembly of the top central planes (2)


Assembly of the final top plane

Female Pin

Male Pin

You need to drill 3 holes in the back side of the center planes to insert the male centering pins. These male centering pins fit perfectly into the hollow female centering pins inserted in the front side of the fixed / central planes

Drill 3 holes in the front side of the center planes to insert the female centering pins.

Note: Dimensions for drilling the male and female centering pins remain the same as demonstrated in the table on pg. 17

Male Pin

Plastic Locking Clip

You need to drill 3 holes in the back side of the final top plane to insert the male centering pins.

Two plastic locking clips need to be installed under the final top plane. These locking clips get secured onto the protrusions present on either sides of the sliding guides, thereby anchoring and stabilising the entire table extension.



Alternative to using male and female centering pins for joining planes


If you do not prefer using the male and female centering pins for the purpose of joining the planes, you could use hinges like in LUNCH. The two options are:

For Wood Thickness (mm) 13 - 19

Dim. A 9.6 mm

Dim. B 43 mm

Dim. C 22 mm

Dim. D 5.5 mm

Dim. E 6 mm

Gap F 17.1 mm

Gap G 2.4 mm

Gap H 2.7 mm

Article No.:341.31.519 Folding Leaf Hinge, Zinc Alloy, Yellow Chromatised, For 18 to 19 mm thick panel

Article No.:341.07.718 Concealed Hinge, Opening Angle180°, Nickel Plated, For 13 to 19 mm thick panel

Note:

• The BOM for PARTY MENSOLA includes the male and female centering pins as the default option. In case you wish to install hinges, you will have to order them separately

• You will have to use 3 hinges to join two planes, hence you will have to order 9 hinges for connecting all the planes to each other

• Please keep in mind that since the planes, with the use of hinges, will be connected to each other, it will make folding and unfolding of the planes a strenuous activity



Using hinges for the frontal cabinet door


To mount the frontal cabinet door, you can use hinges of your choice but its final height should not be more than 18 mm. Alternatively you could also use flap hinges for a flushed look as demonstrated below:

Positioning of the felts under the top planes

Felts

Place the 12 felts over the top of the sliding guides with the adhesive side facing upwards. Place the two central and the final top plane in their positions following the indicated sequence so that the felts get glued onto their proper positions on the bottom of the three top planes.

Note: This system can either be mounted in a cabinet of a base unit or can be mounted in a cabinet that is suspended by the help of wall hanging brackets. In case you wish to suspend the cabinet, you will have to order the wall hanging brackets separately

1 2 3


ORDERING INFORMATION

Extendable Table Fittings

Article Number Description MRP (INR)

505.73.944 LUNCH Extension Table Fittings Dimensions: 600 mm (width) × 969 mm (length)

28,063/-

Consists of:

642.19.935 PARTY MENSOLA Extension Table Fittings Dimensions: 900 mm (width) × 1794 mm (length)

91,943/-

Consists of:

Pair of Sliding Guides

Handle (can be cut to size as per the side panel thickness)

Fastening Material

Article No.:341.07.718, Concealed Hinges

Assembled Mechanism

Pair of Lateral Bar

Fastening Material

Plastic Locking Clips

Male and Female Centering Pins

Accessories

Article Number Description MRP (INR)

341.07.718 Concealed Hinge, Opening Angle180°, Nickel Plated, For 13 to 19 mm thick panel 979/-

341.31.519 Folding Leaf Hinge, Zinc Alloy, Yellow Chromatised, For 18 to 19 mm thick panel

732/-

642.51.243 Male and Female Centering Pins (only if additional pieces are required) 14/-

In case of any query / issue, SMS ‘HAFELE’ to 56070 Our customer care executive will get in touch with you and address your

query / issue.

Call us on our dedicated toll-free number: 1800 266 6667 Customer- friendly, deviation-free call connection to our Customer Care

team

Email us on: [email protected]

New Extendable Table Fittings 22

häfele lever handles...new extendable table fittings 2 extendable table fittings by häfele...

Documents