high accuracy model for locating workpiece … support ld lc tnc tc swing clamp lha pneumatic series...

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series

Valve / CouplerHydraulic Unit

Cautions / Others

High-PowerSeries

Manual OperationAccessories

Hole Clamp

SFASFC

Link Clamp

LKALKCLKWLM/LJTMA-2TMA-1

Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT

Expansion Locating Pin

VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB

CustomizedSpring Cylinder

LHCLHSLHWLT/LGTLA-2TLB-2TLA-1

LLW

Air SensingLift Cylinder

Compact Cylinder

LLLLRLLUDPDRDSDT

Introduction ApplicationExamples

ActionDescription Cautions

Model FVAModel No. IndicationSpecifications・External Dimensions

Model FVDModel No. IndicationSpecifications・External Dimensions

Model FVCModel No. IndicationSpecifications・External Dimensions

Application Examples

Short stroke vise is unable to secure

the clearance for loading the workpiece.

When Loading from the Front

Solvable Problems

When Loading from the Side

For the long workpiece, the robot cannot keep it horizontal.

It is unable to secure the clearance for loading the irregular-shape workpiece.

Locked State Released State

Robotic Hand ChangerModel SWR

Robotic HandModel WP□

Short Stroke ViseReleased State

Long Stroke Model for Automatic Transfer with Robot

Centering ViseModel FVC / FVD-L


Model FVAModel FVDModel FVC

Centering Vise

High Accuracy, High Power, Long StrokeFor Gripping Cylindrical Workpiece, and Workpiece Transfer Hand

Classification

CrossSection

Slide Block Model Link Motion Model

Compact High Power Long Stroke Long Stroke

Model FVA

±0.01 mmLocating Repeatability(X-axis Direction)

Features

Slider Stroke(One Side)

±0.03 mm

FVC0630：10 mmFVC1000：15 mmFVC1600：20 mm

FVA0400：5 mmFVA0630：5 mmFVA1000：5 mm

FVD1600：6 mmFVD2500：8 mmFVD4000：8 mm

FVD1600-L：12 mmFVD2500-L：16 mmFVD4000-L：16 mm

Accessories・Speed Control Valve ： Model BZL・Air Bleed Valve ： Model BZX・G Thread Plug (With Air Breeding Function) ： Model JZG

Double ActionMAX. 7 MPa

Model FVCModel FVD Model FVD-L

High Accuracy Model for Locating Workpiece

High AccuracyHigh Accuracy and High Power

High Accuracy and Long Stroke

Long Stroke of Link Motion Model

Centering ViseModel FVA / FVD

Slide Block

Link Lever

NEW

→ P.891

→ P.885→ P.873 → P.877 → P.877

869

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensions

Application Examples

Short stroke vise is unable to secure

the clearance for loading the workpiece.

When Loading from the Front

Solvable Problems

When Loading from the Side

For the long workpiece, the robot cannot keep it horizontal.

It is unable to secure the clearance for loading the irregular-shape workpiece.

Locked State Released State

Robotic Hand ChangerModel SWR


Short Stroke ViseReleased State

Long Stroke Model for Automatic Transfer with Robot

Centering ViseModel FVC / FVD-L


Model FVAModel FVDModel FVC

Centering Vise

High Accuracy, High Power, Long StrokeFor Gripping Cylindrical Workpiece, and Workpiece Transfer Hand

Classification

CrossSection

Slide Block Model Link Motion Model

Compact High Power Long Stroke Long Stroke

Model FVA

±0.01 mmLocating Repeatability(X-axis Direction)

Features

Slider Stroke(One Side)

±0.03 mm

FVC0630：10 mmFVC1000：15 mmFVC1600：20 mm

FVA0400：5 mmFVA0630：5 mmFVA1000：5 mm

FVD1600：6 mmFVD2500：8 mmFVD4000：8 mm

FVD1600-L：12 mmFVD2500-L：16 mmFVD4000-L：16 mm

Accessories・Speed Control Valve ： Model BZL・Air Bleed Valve ： Model BZX・G Thread Plug (With Air Breeding Function) ： Model JZG

Double ActionMAX. 7 MPa

Model FVCModel FVD Model FVD-L

High Accuracy Model for Locating Workpiece

High AccuracyHigh Accuracy and High Power

High Accuracy and Long Stroke

Long Stroke of Link Motion Model

Centering ViseModel FVA / FVD

Slide Block

Link Lever

NEW

→ P.891

→ P.885→ P.873 → P.877 → P.877

870

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVA/FVD/FVCCentering Vise

Action Description：Slide Block Model

Action Description：Link Motion Model

Model FVC

Release Action

Slider is opened with the movement of the link lever

by supplying hydraulic pressure to the release port.

Lock Action

Model FVA/FVD

Slider is closed with the movement of the link lever

by supplying hydraulic pressure to the lock port.

Release Action

Slide block is ascended to open the slider


Lock Action

Slide block is descended to close the slider


ReleaseHydraulic Port

LockHydraulic Port


Workpiece

Slider

Workpiece

LockHydraulic Port

Air BlowPort

Air BlowPort

Long Stroke

Link motion mechanism allows for wider stroke of the slider and

easy loading/unloading of workpieces. Suitable for automatic transfer.

High Accuracy

Slide block design enables high repeatability and is suitable for high accuracy application.

Link Motion Mechanism

Locating Repeatability (X-axis Direction)： ±0.01 mm

Slide Block

Air Blow Function!

The dust cover and air blow prevent foreign substance and enable a longer operational l ife span.

Excel lent Maintainabil ity!

The grease nipple is equipped for lubricating internal parts.

Equipped with Dust Cover!Dust CoverDust Cover

Grease Nipple

Offset Amount

Easy to Machine the Mounting Surface of the Clamp Lever!

Secure Locking of Workpiece with Powerful Gripping Force!

Offset Available!

Only key slot and bolt hole need to be machined for mounting the clamp lever.

No need complicated serration machining.

Offset of the workpiece is available.

Drill tools are accessible avoiding interference with loaders etc.※ Please contact us when using it with offset.

FVC Only

FVC Only

Slider

Link Lever

Ability to Attach Speed Control Valve


Air Blow Port

871

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVA/FVD/FVCCentering Vise

Action Description：Slide Block Model

Action Description：Link Motion Model

Model FVC

Release Action

Slider is opened with the movement of the link lever


Lock Action

Model FVA/FVD

Slider is closed with the movement of the link lever


Release Action

Slide block is ascended to open the slider


Lock Action

Slide block is descended to close the slider



LockHydraulic Port


Workpiece

Slider

Workpiece

LockHydraulic Port

Air BlowPort

Air BlowPort

Long Stroke

Link motion mechanism allows for wider stroke of the slider and

easy loading/unloading of workpieces. Suitable for automatic transfer.

High Accuracy

Slide block design enables high repeatability and is suitable for high accuracy application.

Link Motion Mechanism

Locating Repeatability (X-axis Direction)： ±0.01 mm

Slide Block

Air Blow Function!

The dust cover and air blow prevent foreign substance and enable a longer operational l ife span.

Excel lent Maintainabil ity!

The grease nipple is equipped for lubricating internal parts.

Equipped with Dust Cover!Dust CoverDust Cover

Grease Nipple

Offset Amount

Easy to Machine the Mounting Surface of the Clamp Lever!

Secure Locking of Workpiece with Powerful Gripping Force!

Offset Available!

Only key slot and bolt hole need to be machined for mounting the clamp lever.

No need complicated serration machining.

Offset of the workpiece is available.

Drill tools are accessible avoiding interference with loaders etc.※ Please contact us when using it with offset.

FVC Only

FVC Only

Slider

Link Lever



Air Blow Port

872

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVACentering Vise　Slide Block Model (Compact)

Model No. Indication Clamping Force Curve

L=30 mmL=0 mm

L=50 mmL=70 mmL=90 mm

L=30 mm

L=0 mm

L=0 mm


L=30 mmL=50 mmL=70 mmL=90 mm

P：Hydraulic Pressure (MPa)



F：Clamping Force (kN)



0

1

2

3

4

5

0 1 2 3 4 5 6 7

0

2

4

6

8

10

0 1 2 3 4 5 6 7

0

2

4

6

8

10

12

14

0 1 2 3 4 5 6 7

Non-Usable Range (■)



L ： Clamping Height (mm)

7 6 5 4 3 2 1.5

FVA0400Calculation Formula ※4 (kN) F=(148×P) / (183+L)

Clamping Height L (mm)

Clamping Force (kN) Non-Usable Range (■)

7 6 5 4 3 2 1.5




7 6 5 4 3 2 1.5




HydraulicPressure(MPa)



Clamping Force (kN)

Clamping Force (kN)

Specifications

2

0 ： Revision Number

Design No.

１ 2

FVA 063 0

Model No. Slider Stroke (One Side) Max. Clamping Height (At 7MPa) Cylinder Area

Cylinder Capacity Max. Operating Pressure Min. Operating Pressure Withstanding Pressure Locating Repeatability (X-axis Direction) Operating Temperature Usable Fluid Weight

FVA0400

506.06.05.55.5

2.5

FVA063056510.010.09.19.17.01.510.5±0.010 ～ 70

General Hydraulic Oil Equivalent to ISO-VG323.4

FVA1000

7515.815.814.414.4

4.3

mmmm

MPaMPaMPamm℃

kg

Notes： 1. Adjust the operating speed so that the slider fully strokes within 1~2 seconds. 2. Secure the extra stroke of 1mm or more. ※2. Locating repeatability under the same condition.

※2

Lock Release Lock Releasecm3

cm2

1 Clamping Force

040 ： Clamping Force 5.2 kN (At Hydraulic Pressure 7 MPa, Clamping Height 15mm)



Note： ※1. F indicates the total value of clamping force (kN) on both sides.

※1

Notes： 1. This table and graph show the relationship among F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), and L：Clamping Height (mm). 2. Using in the non-usable range may damage the product and lead to fluid leakage. 3. When load is applied from the same direction (X-axis direction), please consider it referring to F/2：clamping force on one side. ※3. F indicates the total value of clamping force (kN) on both sides. ※4. F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), L：Clamping Height (mm). P ： Hydraulic Pressure (MPa)

L ： Clamping Height 15mm

P ： Hydraulic Pressure 7MPa

※1F/2 (kN) ※1F/2 (kN)

※3F/2 (kN)※3F/2 (kN)Ｘ

304.864.173.472.782.081.391.04

504.453.813.182.541.911.270.95

70

2.922.341.751.170.88

90

2.171.631.080.81

308.146.975.814.653.492.321.74

507.506.435.354.283.212.141.61

70

5.964.963.972.981.991.49

90

4.633.702.781.851.39

3013.1311.259.387.505.633.752.81

5012.1710.438.706.965.223.482.61

7011.359.738.116.494.863.242.43

90

9.117.596.084.563.042.28

873

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT






Model No. Indication Clamping Force Curve

L=30 mmL=0 mm


L=30 mm

L=0 mm

L=0 mm


L=30 mmL=50 mmL=70 mmL=90 mm







0

1

2

3

4

5

0 1 2 3 4 5 6 7

0

2

4

6

8

10

0 1 2 3 4 5 6 7

0

2

4

6

8

10

12

14

0 1 2 3 4 5 6 7





7 6 5 4 3 2 1.5



Clamping Force (kN) Non-Usable Range (■)

7 6 5 4 3 2 1.5




7 6 5 4 3 2 1.5







Clamping Force (kN)

Clamping Force (kN)

Specifications

2


Design No.

１ 2

FVA 063 0


Cylinder Capacity Max. Operating Pressure Min. Operating Pressure Withstanding Pressure Locating Repeatability (X-axis Direction) Operating Temperature Usable Fluid Weight

FVA0400

506.06.05.55.5

2.5

FVA063056510.010.09.19.17.01.510.5±0.010 ～ 70


FVA1000

7515.815.814.414.4

4.3

mmmm

MPaMPaMPamm℃

kg


※2

Lock Release Lock Releasecm3

cm2

1 Clamping Force




Note： ※1. F indicates the total value of clamping force (kN) on both sides.

※1

Notes： 1. This table and graph show the relationship among F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), and L：Clamping Height (mm). 2. Using in the non-usable range may damage the product and lead to fluid leakage. 3. When load is applied from the same direction (X-axis direction), please consider it referring to F/2：clamping force on one side. ※3. F indicates the total value of clamping force (kN) on both sides. ※4. F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), L：Clamping Height (mm). P ： Hydraulic Pressure (MPa)



※1F/2 (kN) ※1F/2 (kN)

※3F/2 (kN)※3F/2 (kN)Ｘ

304.864.173.472.782.081.391.04

504.453.813.182.541.911.270.95

70

2.922.341.751.170.88

90

2.171.631.080.81

308.146.975.814.653.492.321.74

507.506.435.354.283.212.141.61

70

5.964.963.972.981.991.49

90

4.633.702.781.851.39

3013.1311.259.387.505.633.752.81

5012.1710.438.706.965.223.482.61

7011.359.738.116.494.863.242.43

90

9.117.596.084.563.042.28

874

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT






Model No.ABCDEFGHJKLMNP

Q (Nominal×Pitch×Depth)RSTUVWXYZAAAB

AC (Nominal×Pitch×Depth)Parallel Key

FVA040050100722394520397184　　14246

M6×1×123219.54191531223.519.542.522.5

M5×0.8×104×4×20

FVA0630551108026155023439184　　16287

M8×1.25×133521.5461016.536225.521.54825

M5×0.8×104×4×25

FVA1000601208528156520499225　　17.528-

M10×1.5×1542.524.551101736.52.529.524.552.532.5

M6×1×125×5×25

(mm)

+ 0.022+ 0.004

+ 0.022+ 0.004

+ 0.022+ 0.004

External Dimensions and Machining Dimensions for Mounting

★

★

★

★

★

★

★

★

Release Port

AB ABAA AA

8-φ9 Through Hole

Clamping Height

5C

AD

J K M

5 (Slider Stroke)

T

R R

SSU

U

G F G

B(E)8-φ5.5

Spot Facingφ9 Depth P

Release PortO-ring OR NBR-90 P7-N (1BP7) (Included)

O-ring OR NBR-90 P7-N (1BP7) (Included)Lock Port

8-M8×1.25 Thread Depth 15

2-Parallel Key (Square End)(Included)

2-Parallel Pin (Included)φ5×10 (B Type)

φ5 or less

3.5

φ14W

V

2-Grease Nipple(Included)

HY

X

4- Q Screw

5.5N

5.5Lever

(Prepared by Customer)

11

11 R5.5

8-φ6.8

8

FVA1000

(Except FVA1000)Z

ZUU

ZZ

UU

R R

AB ABAA AA

S

T

8-AC ScrewLock Port

φ5

φ52-φ5H8　　　Depth 6

±0.01

±0.01

±0.1

±0.01 ±0.01

±0.01 ±0.01

±0.1R RT

±0.01 ±0.01

±0.1

±0.01

S±0.01

S±0.01

S±0.01

External Dimensions

Machining Dimensions of Mounting Area

※ The drawing shows the released state of FVA.

+ 0.018 0

Release Port：G1/8 Thread (Speed Control Valve Port)

Lock Port：G1/8 Thread (Speed Control Valve Port)

2-G Thread Plug

Mounting from the Top Mounting from the Bottom

(Mounting Bolt)

Release Portφ5

6.3S

Lock Portφ5

Ｘ

(Slot Width)LG8

※2

※1

※2

(Included)

2-φ5H8　　　Depth 6+ 0.018 0

FVA0400 has only four holes marked with ★.

FVA0400 has only fourholes marked with ★.

Notes: 1. Roughness of mounting surface should be 6.3S or better. 2. Install a lever on the top of the slider when in use. ※1. Mounting bolts are not provided with the product. Please prepare them according to the mounting height referring to dimension 'C'. ※2. Speed control valve is sold separately. Please refer to P.891 for detail.

875

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT






Model No.ABCDEFGHJKLMNP

Q (Nominal×Pitch×Depth)RSTUVWXYZAAAB

AC (Nominal×Pitch×Depth)Parallel Key

FVA040050100722394520397184　　14246

M6×1×123219.54191531223.519.542.522.5

M5×0.8×104×4×20

FVA0630551108026155023439184　　16287

M8×1.25×133521.5461016.536225.521.54825

M5×0.8×104×4×25

FVA1000601208528156520499225　　17.528-

M10×1.5×1542.524.551101736.52.529.524.552.532.5

M6×1×125×5×25

(mm)

+ 0.022+ 0.004

+ 0.022+ 0.004

+ 0.022+ 0.004


★

★

★

★

★

★

★

★

Release Port

AB ABAA AA

8-φ9 Through Hole

Clamping Height

5C

AD

J K M

5 (Slider Stroke)

T

R R

SSU

U

G F G

B(E)8-φ5.5

Spot Facingφ9 Depth P



8-M8×1.25 Thread Depth 15


2-Parallel Pin (Included)φ5×10 (B Type)

φ5 or less

3.5

φ14W

V


HY

X

4- Q Screw

5.5N

5.5Lever

(Prepared by Customer)

11

11 R5.5

8-φ6.8

8

FVA1000

(Except FVA1000)

ZZ

UU

ZZ

UU

R R

AB ABAA AA

S

T

8-AC ScrewLock Port

φ5

φ52-φ5H8　　　Depth 6

±0.01

±0.01

±0.1

±0.01 ±0.01

±0.01 ±0.01

±0.1R RT

±0.01 ±0.01

±0.1

±0.01

S±0.01

S±0.01

S±0.01

External Dimensions


※ The drawing shows the released state of FVA.

+ 0.018 0

Release Port：G1/8 Thread (Speed Control Valve Port)

Lock Port：G1/8 Thread (Speed Control Valve Port)

2-G Thread Plug


(Mounting Bolt)

Release Portφ5

6.3S

Lock Portφ5

Ｘ

(Slot Width)LG8

※2

※1

※2

(Included)

2-φ5H8　　　Depth 6+ 0.018 0

FVA0400 has only four holes marked with ★.

FVA0400 has only fourholes marked with ★.

Notes: 1. Roughness of mounting surface should be 6.3S or better. 2. Install a lever on the top of the slider when in use. ※1. Mounting bolts are not provided with the product. Please prepare them according to the mounting height referring to dimension 'C'. ※2. Speed control valve is sold separately. Please refer to P.891 for detail.

876

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External DimensionsCentering Vise　Slide Block Model model FVD

Model No. Indication MEMO

Specifications

2


Design No.

3

Blank ： Standard Stroke

L ： Long Stroke

Stroke Code

1 Clamping Force

160 ： Clamping Force 32 kN (At Hydraulic Pressure 7 MPa, Clamping Height 15mm)



１ 2 3

FVD 160 0 -


Cylinder Capacity

Max. Operating Pressure Min. Operating Pressure Withstanding Pressure Locating Repeatability (X-axis Direction) Operating Temperature Usable Fluid Weight

　 Blank selected 　 L selected 　 Blank selected 　 L selected　 Lock Release Lock Release

FVD1600-□6126010019.521.248.552.9

7.6

FVD2500-□8166510030.633.2100.8109.27.01.510.5±0.010 ～ 70

General Hydraulic Oil Equivalent to ISO-VG3213

FVD4000-□8167010048.756.7160.2186.7

20

MPaMPaMPamm℃

kg

cm3

cm2

mm

mm


Notes： ※1. Clamping Force of 　 Blank：Standard Stroke Refer to the clamping force curve for clamping force of L：Long Stroke. ※2. F indicates the total value of clamping force (kN) on both sides.

※3

※1 ※2

3

3

3

3

3

3


※2F/2 (kN) ※2F/2 (kN)


877

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External DimensionsCentering Vise　Slide Block Model model FVD

Model No. Indication MEMO

Specifications

2


Design No.

3

Blank ： Standard Stroke

L ： Long Stroke

Stroke Code

1 Clamping Force




１ 2 3

FVD 160 0 -


Cylinder Capacity

Max. Operating Pressure Min. Operating Pressure Withstanding Pressure Locating Repeatability (X-axis Direction) Operating Temperature Usable Fluid Weight

　 Blank selected 　 L selected 　 Blank selected 　 L selected　 Lock Release Lock Release

FVD1600-□6126010019.521.248.552.9

7.6

FVD2500-□8166510030.633.2100.8109.27.01.510.5±0.010 ～ 70

General Hydraulic Oil Equivalent to ISO-VG3213

FVD4000-□8167010048.756.7160.2186.7

20

MPaMPaMPamm℃

kg

cm3

cm2

mm

mm


Notes： ※1. Clamping Force of 　 Blank：Standard Stroke Refer to the clamping force curve for clamping force of L：Long Stroke. ※2. F indicates the total value of clamping force (kN) on both sides.

※3

※1 ※2

3

3

3

3

3

3


※2F/2 (kN) ※2F/2 (kN)


878

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVDCentering Vise　Slide Block Model

Clamping Force Curve

Notes： 1. This table and graph show the relationship among F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), and L：Clamping Height (mm). 2. Using in the non-usable range may damage the product and lead to fluid leakage. 3. When load is applied from the same direction (X-axis direction), please consider it referring to F/2：clamping force on one side. ※1. F indicates the total value of clamping force (kN) on both sides. ※2. F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), L：Clamping Height (mm).


FVD-L Long StrokeFVD Standard Stroke

10 2 3 4 5 6 7

10 2 3 4 5 6 7

10 2 3 4 5 6 7

L=0 mm

L=50 mm

L=100 mm

L=150 mm

L=0 mm

L=50 mmL=100 mmL=150 mm

L=0 mm

L=50 mmL=100 mmL=150 mm





7 6 5 4 3 2 1.5

FVD1600Calculation Formula ※2 (kN)

Clamping Height L (mm) Clamping Force (kN) Non-Usable Range (■)

7 6 5 4 3 2 1.5

FVD2500

7 6 5 4 3 2 1.5

FVD4000




Calculation Formula ※2 (kN)

Clamping Height L (mm) Clamping Force (kN) Non-Usable Range (■)HydraulicPressure(MPa)






10 2 3 4 5 6 7

10 2 3 4 5 6 7

10 2 3 4 5 6 7

L=0 mm

L=50 mm

L=100 mm

L=150 mm

L=0 mm

L=50 mm

L=100 mmL=150 mm

L=0 mm

L=50 mm

L=100 mmL=150 mm









7 6 5 4 3 2 1.5

FVD1600-L

7 6 5 4 3 2 1.5

FVD2500-L

7 6 5 4 3 2 1.5

FVD4000-L








0

4

8

12

16

20

24

28

32

36

0

10

20

30

40

50

60

0

10

20

30

40

50

60

70

80

90

0

4

8

12

16

20

0

4

8

12

16

20

24

28

32

0

10

20

30

40

50

F=(1556×P) / (323+L)

033.7228.9024.0919.2714.459.637.23

5029.2025.0320.8616.6912.518.346.26

100

14.7111.047.365.52

F=(2936×P) / (394+L)

052.1644.7137.2629.8122.3614.9011.18

5046.2939.6833.0626.4519.8413.239.92

100

29.7223.7717.8311.898.91

150

21.5916.1910.798.10

F=(5340×P) / (446+L)

083.8171.8459.8747.8935.9223.9517.96

5075.3664.6053.8343.0632.3021.5316.15

100

48.9039.1229.3419.5614.67

150

35.8426.8817.9213.44

150

9.876.584.93

F=(836×P) / (302+L)

019.3816.6113.8411.078.305.544.15

5016.6314.2511.889.507.134.753.56

10014.5612.4810.408.326.244.163.12

F=(1538×P) / (357+L)

030.1625.8521.5417.2312.928.626.46

5026.4522.6718.8915.1211.347.565.67

10023.5620.1916.8313.4610.106.735.05

150

15.1712.139.106.074.55

F=(2938×P) / (425+L)

048.3941.4834.5627.6520.7413.8310.37

5043.3037.1130.9324.7418.5612.379.28

10039.1733.5827.9822.3816.7911.198.39

150

25.5520.4415.3310.227.66

150

9.257.405.553.702.77

P：Hydraulic Pressure (MPa)P：Hydraulic Pressure (MPa)

※1F/2 (kN)

Slider

※1F/2 (kN)Ｘ

879

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVDCentering Vise　Slide Block Model


Notes： 1. This table and graph show the relationship among F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), and L：Clamping Height (mm). 2. Using in the non-usable range may damage the product and lead to fluid leakage. 3. When load is applied from the same direction (X-axis direction), please consider it referring to F/2：clamping force on one side. ※1. F indicates the total value of clamping force (kN) on both sides. ※2. F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), L：Clamping Height (mm).


FVD-L Long StrokeFVD Standard Stroke

10 2 3 4 5 6 7

10 2 3 4 5 6 7

10 2 3 4 5 6 7

L=0 mm

L=50 mm

L=100 mm

L=150 mm

L=0 mm

L=50 mmL=100 mmL=150 mm

L=0 mm

L=50 mmL=100 mmL=150 mm





7 6 5 4 3 2 1.5

FVD1600Calculation Formula ※2 (kN)

Clamping Height L (mm) Clamping Force (kN) Non-Usable Range (■)

7 6 5 4 3 2 1.5

FVD2500

7 6 5 4 3 2 1.5

FVD4000











10 2 3 4 5 6 7

10 2 3 4 5 6 7

10 2 3 4 5 6 7

L=0 mm

L=50 mm

L=100 mm

L=150 mm

L=0 mm

L=50 mm

L=100 mmL=150 mm

L=0 mm

L=50 mm

L=100 mmL=150 mm









7 6 5 4 3 2 1.5

FVD1600-L

7 6 5 4 3 2 1.5

FVD2500-L

7 6 5 4 3 2 1.5

FVD4000-L








0

4

8

12

16

20

24

28

32

36

0

10

20

30

40

50

60

0

10

20

30

40

50

60

70

80

90

0

4

8

12

16

20

0

4

8

12

16

20

24

28

32

0

10

20

30

40

50

F=(1556×P) / (323+L)

033.7228.9024.0919.2714.459.637.23

5029.2025.0320.8616.6912.518.346.26

100

14.7111.047.365.52

F=(2936×P) / (394+L)

052.1644.7137.2629.8122.3614.9011.18

5046.2939.6833.0626.4519.8413.239.92

100

29.7223.7717.8311.898.91

150

21.5916.1910.798.10

F=(5340×P) / (446+L)

083.8171.8459.8747.8935.9223.9517.96

5075.3664.6053.8343.0632.3021.5316.15

100

48.9039.1229.3419.5614.67

150

35.8426.8817.9213.44

150

9.876.584.93

F=(836×P) / (302+L)

019.3816.6113.8411.078.305.544.15

5016.6314.2511.889.507.134.753.56

10014.5612.4810.408.326.244.163.12

F=(1538×P) / (357+L)

030.1625.8521.5417.2312.928.626.46

5026.4522.6718.8915.1211.347.565.67

10023.5620.1916.8313.4610.106.735.05

150

15.1712.139.106.074.55

F=(2938×P) / (425+L)

048.3941.4834.5627.6520.7413.8310.37

5043.3037.1130.9324.7418.5612.379.28

10039.1733.5827.9822.3816.7911.198.39

150

25.5520.4415.3310.227.66

150

9.257.405.553.702.77


※1F/2 (kN)

Slider

※1F/2 (kN)Ｘ

880

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVDCentering Vise　Slide Block Model (High Power)

External Dimensions and Machining Dimensions for Mounting (mm)Model No.

Slider Stroke (One Side)ABCDEFGHJKL1L2MNPQRS

T (Nominal×Pitch×Depth)UVWXY

Z (Hole Diameter×Depth)Z1AAABACADAEAFAG

AH (Nominal×Pitch×Depth)BABBBC

BD (Nominal×Pitch×Depth)BEBFJAJBO-ring

Parallel KeyG Thread

FVD1600690170677066.54211265

8　　　7660476.811422027.515

M8×1.25×12840495538

6　　×6618761211551816

M8×1.25×16773038

M6×1×1195314

OR NBR-90 P7-N (1BP7)8×7×40G 1/8

FVD25008100206828581.55414070

8　　　8474578.71450223018.5

M10×1.5×15104556.56842

8　　×8818941413732016

M10×1.5×20943742

M8×1.25×13115314

OR NBR-90 P7-N (1BP7)10×8×45G 1/8

FVD400081182408911088.55815180

10　　　98906410.517.553283421

M12×1.75×181055647549

8　　×88211081515902316

M12×1.75×241094549

M10×1.5×15146.8419

OR NBR-90 P9-N (1BP9)10×8×50G 1/4

- 0.005- 0.027

- 0.005- 0.027

- 0.005- 0.027

+ 0.018 0

+ 0.022 0

+ 0.022 0

External Dimensions：FVD Standard Stroke※ The drawing shows the released state of FVD.

AVQ

BL2

φAGL1 L2

JA

K

WWRSU U

Ｘ

※1

HJg8

AE AE

AC AFAD

φD -0.1-0.2

φJB

C

G

FE

P

※3

AAAA

AB±0.1

X±0.01 X±0.01

Y±0.01

Y±0.01

2-φZ H8

Notes: 1. Roughness of mounting surface should be 6.3S or better. 2. Install a lever on the top of the slider when in use. ※1. Mounting bolts are not provided with the product. Please prepare them according to the mounting height referring to dimension 'P'. ※2. Speed control valve is sold separately. Please refer to P.891 for detail. ※3. Able to locate the body of centering vise by using φZ hole. Please consider X, Y dimension tolerance and φZ1 hole tolerance according to the locating pin. Locating pin is not included. ※4. When shipping, R-thread plugs are mounted to the grease nipple installation port. Select one port each from ☆ and ★ ports and install the grease nipples to the selected ports. ※5. When using the lubrication port, remove the set screws. ※6. This machining is required only when using the lubrication port.

Grease Nipple Installation Port

※4Grease Nipple Installation Port：6-Rc1/8 Thread


6-R-Thread Plug (Included)

(0～2)

※3

※3 ※3

※3

※3

BA BABB BB

AB±0.1X X

BCBC

AAAA

ＹＹ

Lock PortφBF or less

Release PortφBF or less

BABB BB

BA

AB±0.1X X

AAAA

BCBC Y

Y

φD+ 0.3

0

φD+ 0.3

0



2-φZ1※3

※3 ※3

※3

※3

2-φZ1

8-φBE Hole8-BD Screw


6.3S

F+2 or more

C1

Blind Hole Machining Through Hole Machining

6.3S

F+2 or more

C1



※6

※6 ※6

2-Lubrication Port φBF or less

AE AE※6 ※6AE AE

AE AE

※52-Lubrication PortO-ring (Included)

M3×0.5×4 Set Screw (Included)

※62-Lubrication Port φBF or less

Lever(Prepared by Customer)

Clamping Height


8-T Screw

Slider Stroke Slider Stroke

※2

※2

Release PortO-ring (Included)

Lock PortO-ring (Included)

8-AH Screw

Release Port：G Thread (Speed Control Valve Port)

Lock Port：G Thread (Speed Control Valve Port)

8-φMSpot FacingφN

2-G Thread Plug(Included)

881

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVDCentering Vise　Slide Block Model (High Power)

External Dimensions and Machining Dimensions for Mounting (mm)Model No.

Slider Stroke (One Side)ABCDEFGHJKL1L2MNPQRS

T (Nominal×Pitch×Depth)UVWXY





FVD1600690170677066.54211265

8　　　7660476.811422027.515

M8×1.25×12840495538

6　　×6618761211551816

M8×1.25×16773038

M6×1×1195314

OR NBR-90 P7-N (1BP7)8×7×40G 1/8

FVD25008100206828581.55414070

8　　　8474578.71450223018.5

M10×1.5×15104556.56842

8　　×8818941413732016

M10×1.5×20943742

M8×1.25×13115314

OR NBR-90 P7-N (1BP7)10×8×45G 1/8

FVD400081182408911088.55815180

10　　　98906410.517.553283421

M12×1.75×181055647549

8　　×88211081515902316

M12×1.75×241094549

M10×1.5×15146.8419

OR NBR-90 P9-N (1BP9)10×8×50G 1/4

- 0.005- 0.027

- 0.005- 0.027

- 0.005- 0.027

+ 0.018 0

+ 0.022 0

+ 0.022 0

External Dimensions：FVD Standard Stroke※ The drawing shows the released state of FVD.

AVQ

BL2

φAGL1 L2

JA

K

WWRSU U

Ｘ

※1

HJg8

AE AE

AC AFAD

φD -0.1-0.2

φJB

C

G

FE

P

※3

AAAA

AB±0.1

X±0.01 X±0.01

Y±0.01

Y±0.01

2-φZ H8






(0～2)

※3

※3 ※3

※3

※3

BA BABB BB

AB±0.1X X

BCBC

AAAA

ＹＹ



BABB BB

BA

AB±0.1X X

AAAA

BCBC Y

Y

φD+ 0.3

0

φD+ 0.3

0



2-φZ1※3

※3 ※3

※3

※3

2-φZ1



6.3S

F+2 or more

C1


6.3S

F+2 or more

C1



※6

※6 ※6

2-Lubrication Port φBF or less

AE AE※6 ※6AE AE

AE AE





Clamping Height


8-T Screw

Slider Stroke Slider Stroke

※2

※2



8-AH Screw



8-φMSpot FacingφN


882

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVD-LCentering Vise　Slide Block Model (Long Stroke)



※6 ※6AE AE

External Dimensions：FVD-L Long Stroke※ The drawing shows the released state of FVD-L.

※3

※3 ※3

※3

※3

BA BABB BB

AB±0.1X X

BCBC

AAAA

ＹＹ



BABB BB

BA

AB±0.1X X

AAAA

BCBC Y

Y

φD+ 0.3

0

φD+ 0.3

0



2-φZ1※3

※3 ※3

※3

※3

2-φZ1




6.3S

F+2 or more

C1

Through Hole Machining

6.3S

F+2 or more

C1



Model No.Slider Stroke (One Side)

ABCDEFGHJKL1L2MNPQRS

T (Nominal×Pitch×Depth)UU1VWXY





FVD1600-L1290170677066.54211265

8　　　7660476.81142201620

M8×1.25×128224042.55538

6　　×6618761211551816

M8×1.25×16773038

M6×1×1195314

OR NBR-90 P7-N (1BP7)8×7×40G 1/8

FVD2500-L16100206828581.55414070

8　　　8474578.71450221426

M10×1.5×15102245486842

8　　×8818941413732016

M10×1.5×20943742

M8×1.25×13115314

OR NBR-90 P7-N (1BP7)10×8×45G 1/8

FVD4000-L161182408911088.55815180

10　　　98906410.517.5532818.528

M12×1.75×181027.55555.57549

8　　×88211081515902316

M12×1.75×241094549

M10×1.5×15146.8419

OR NBR-90 P9-N (1BP9)10×8×50G 1/4

(mm)

- 0.005- 0.027

- 0.005- 0.027

- 0.005- 0.027

+ 0.018 0

+ 0.022 0

+ 0.022 0

AVQ

BL2 L1 L2

JA

K

WWRSU1 U




(0～2)

φAG

Ｘ

φD -0.1-0.2

φJB

CAE AE

AF

※1

HJg8

AC AD

G

FE

P

※3

AAAA

AB±0.1

X±0.01 X±0.01

Y±0.01

Y±0.01

2-φZ H8



AE AE

※6 ※6AE AE



Blind Hole Machining Blind Hole Machining

8-φMSpot FacingφN


Clamping HeightSlider Stroke Slider Stroke


8-AH Screw




8-T Screw

※2

※2



883

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVD-LCentering Vise　Slide Block Model (Long Stroke)



※6 ※6AE AE

External Dimensions：FVD-L Long Stroke※ The drawing shows the released state of FVD-L.

※3

※3 ※3

※3

※3

BA BABB BB

AB±0.1X X

BCBC

AAAA

ＹＹ



BABB BB

BA

AB±0.1X X

AAAA

BCBC Y

Y

φD+ 0.3

0

φD+ 0.3

0



2-φZ1※3

※3 ※3

※3

※3

2-φZ1




6.3S

F+2 or more

C1


6.3S

F+2 or more

C1




ABCDEFGHJKL1L2MNPQRS

T (Nominal×Pitch×Depth)UU1VWXY





FVD1600-L1290170677066.54211265

8　　　7660476.81142201620

M8×1.25×128224042.55538

6　　×6618761211551816

M8×1.25×16773038

M6×1×1195314

OR NBR-90 P7-N (1BP7)8×7×40G 1/8

FVD2500-L16100206828581.55414070

8　　　8474578.71450221426

M10×1.5×15102245486842

8　　×8818941413732016

M10×1.5×20943742

M8×1.25×13115314

OR NBR-90 P7-N (1BP7)10×8×45G 1/8

FVD4000-L161182408911088.55815180

10　　　98906410.517.5532818.528

M12×1.75×181027.55555.57549

8　　×88211081515902316

M12×1.75×241094549

M10×1.5×15146.8419

OR NBR-90 P9-N (1BP9)10×8×50G 1/4

(mm)

- 0.005- 0.027

- 0.005- 0.027

- 0.005- 0.027

+ 0.018 0

+ 0.022 0

+ 0.022 0

AVQ

BL2 L1 L2

JA

K

WWRSU1 U




(0～2)

φAG

Ｘ

φD -0.1-0.2

φJB

CAE AE

AF

※1

HJg8

AC AD

G

FE

P

※3

AAAA

AB±0.1

X±0.01 X±0.01

Y±0.01

Y±0.01

2-φZ H8



AE AE

※6 ※6AE AE




8-φMSpot FacingφN


Clamping HeightSlider Stroke Slider Stroke


8-AH Screw




8-T Screw

※2

※2



884

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVCCentering Vise　Link Motion Model (Long Stroke)

Model No. Indication

Specifications

2


Design No.

1 Cylinder Force

063 ： Cylinder Force 6.6 kN (Hydraulic Pressure 7 MPa)



１ 2

FVC 100 0

Model No. Slider Stroke (One Side) Max. Clamping Height Cylinder Area cm2

Cylinder Capacity cm3

Max. Operating Pressure Min. Operating Pressure Withstanding Pressure Air Blow Operating Pressure Locating Repeatability (X-axis Direction) Operating Temperature Usable Fluid Weight

FVC063010309.412.621.228.3

5.8

FVC1000155015.819.647.558.97.01.510.50.4±0.030 ～ 70


FVC16002010023.428.390.0108.9

21.2

LockReleaseLockRelease

mmmm

MPaMPaMPaMPamm℃

kg


Notes： 1. This graph shows the relationship among F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), L：Clamping Height (mm), and S：Slider Stroke (mm). 2. Using in the non-usable range may damage the product and lead to fluid leakage. 3. When load is applied from the same direction (X-axis direction), please consider it referring to F/2：clamping force on one side. ※4. F indicates the total value of clamping force (kN) on both sides.

※2

Notes: 1. Adjust the operating speed so that the slider fully strokes within 1~2 seconds. 2. Secure the extra stroke of 1mm or more. ※2. Please contact us when exceeding max. clamping height. ※3. Locating repeatability under the same condition.

※3

※1

Note： ※1. Cylinder force is different from clamping force. Refer to the clamping force curve for details of clamping force.

FVC0630

FVC1600

FVC1000

0

4

8

12

0 2 94 6 8 10

S：Slider Stroke (mm)


P=1.5MPa

P=3MPa

P=5MPa

P=7MPa

L=0 mmL=30 mm

0

4

8

12

16

20

0 2 4 5 6 8 10 12 14 15



P=1.5MPa

P=3MPa

P=5MPa

P=7MPa

L=0 mm

L=50 mm

0

4

8

12

16

28

20

24

0 2 4 6 8 10 12 14 16 18 19 20



P=1.5MPa

P=3MPa

P=5MPa

P=7MPa

L=0 mm

L=100 mm


30 mmMax. Clamping Height※2






※4F/2 (kN) ※4F/2 (kN)

Slider

Ｘ



885

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVCCentering Vise　Link Motion Model (Long Stroke)

Model No. Indication

Specifications

2


Design No.

1 Cylinder Force




１ 2

FVC 100 0

Model No. Slider Stroke (One Side) Max. Clamping Height Cylinder Area cm2

Cylinder Capacity cm3

Max. Operating Pressure Min. Operating Pressure Withstanding Pressure Air Blow Operating Pressure Locating Repeatability (X-axis Direction) Operating Temperature Usable Fluid Weight

FVC063010309.412.621.228.3

5.8

FVC1000155015.819.647.558.97.01.510.50.4±0.030 ～ 70


FVC16002010023.428.390.0108.9

21.2

LockReleaseLockRelease

mmmm

MPaMPaMPaMPamm℃

kg


Notes： 1. This graph shows the relationship among F：Clamping Force (kN), P：Supply Hydraulic Pressure (MPa), L：Clamping Height (mm), and S：Slider Stroke (mm). 2. Using in the non-usable range may damage the product and lead to fluid leakage. 3. When load is applied from the same direction (X-axis direction), please consider it referring to F/2：clamping force on one side. ※4. F indicates the total value of clamping force (kN) on both sides.

※2

Notes: 1. Adjust the operating speed so that the slider fully strokes within 1~2 seconds. 2. Secure the extra stroke of 1mm or more. ※2. Please contact us when exceeding max. clamping height. ※3. Locating repeatability under the same condition.

※3

※1

Note： ※1. Cylinder force is different from clamping force. Refer to the clamping force curve for details of clamping force.

FVC0630

FVC1600

FVC1000

0

4

8

12

0 2 94 6 8 10



P=1.5MPa

P=3MPa

P=5MPa

P=7MPa

L=0 mmL=30 mm

0

4

8

12

16

20

0 2 4 5 6 8 10 12 14 15



P=1.5MPa

P=3MPa

P=5MPa

P=7MPa

L=0 mm

L=50 mm

0

4

8

12

16

28

20

24

0 2 4 6 8 10 12 14 16 18 19 20



P=1.5MPa

P=3MPa

P=5MPa

P=7MPa

L=0 mm

L=100 mm








※4F/2 (kN) ※4F/2 (kN)

Slider

Ｘ



886

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External DimensionsCentering Vise　Link Motion Model (Long Stroke) model FVC


ABCDEFGHJKLMNPQRSTU

V (Nominal×Pitch×Depth)WXYZAAABACADAEAFAGAH

AJ (Nominal×Pitch×Depth)AKALAMJAJB

Parallel PinParallel Key

Lock Hydraulic Port：G ThreadRelease Hydraulic Port：G Thread

FVC06301055801826075541293.5192.54042298　　50166.52.542

M6×1×91082M86.89165343471-50

M6×1×125　　 Depth 6

5693.514

φ5×10 (B Type)8×7×20

FVC10001570942347094631573.5242.54454418　　70248560

M8×1.25×1111104.5M86.8131664141973775

M6×1×126　　 Depth 7

6594.519

φ6×12 (B Type)8×7×32

G1/4 G1/4G1/8

FVC1600208211429882116801964302.557625610　　9030104.577

M10×1.5×1515136.5M108.51620849491305090

M8×1.25×168　　 Depth 9

82114.519

φ8×16 (B Type)10×8×45

(mm)External Dimensions and Machining Dimensions for Mounting

+ 0.027+ 0.005

+ 0.027+ 0.005

+ 0.027+ 0.005

+ 0.018 0

+ 0.022 0

+ 0.018 0

QR S

(15)

TN

M N

LSlider Stroke

The Center of the Workpiece

φD -0.1-0.2

AA

GClamping Height

FE

ABAC


８-V Screw

X±0.1 X±0.1

CJA

U±0.05

PG8

PG8

2-Parallel Pin (Included)

JH

Air Blow Port


O-ring 1BP7 (Included)


8-Y Through Tapped HoleφZ Hole

Slider

※1

※2

φ5

φJB

BA

W

WW


※2Lock Port：G Thread (Speed Control Valve Port)

Lever (Prepared by Customer)

Ｘ

K

★

★

FVC0630 has only fourholes marked with ★.★

★

External Dimensions※ The drawing shows the released state of FVC.


2-G Thread Plug

(Slot Width)

(Included)

6.3S

２

φD+ 0.3 0

AL or more

AL or more

30゜ 30゜6.3S2


8-φAM Through Hole

AG AGAF AF

AG AGAF AF

AH±0.01

X±0.1AH±0.01

X±0.1AH±0.01

X ±0.1AH±0.01

X ±0.1

Air Blow Port

８-AJ Screw

２-φAKH8２-φAKH8

φ5

φ5Air Blow Port

φ5

φ5

Lock Portφ5

Lock Port

WW W

ADAD

WW

ADAD

Release Port

AE±0.01AE±0.01

AE±0.01AE±0.01

(Mounting Bolt)

(Mounting Bolt)


W

φ5Release Port

φD+ 0.3 0

Notes: 1. Roughness of mounting surface should be 6.3S or better. 2. Install a lever on the top of the slider when in use. ※1. Mounting bolts are not provided with the product. Please prepare them according to the mounting height referring to dimension 'AB'. ※2. Speed control valve is sold separately. Please refer to P.891 for detail.

FVC0630 has only four holes marked with ★.

★

★

★

★

★

★

★

★



FVC0630 has only four screws marked with ★.


887

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External DimensionsCentering Vise　Link Motion Model (Long Stroke) model FVC


ABCDEFGHJKLMNPQRSTU

V (Nominal×Pitch×Depth)WXYZAAABACADAEAFAGAH

AJ (Nominal×Pitch×Depth)AKALAMJAJB

Parallel PinParallel Key

Lock Hydraulic Port：G ThreadRelease Hydraulic Port：G Thread

FVC06301055801826075541293.5192.54042298　　50166.52.542

M6×1×91082M86.89165343471-50

M6×1×125　　 Depth 6

5693.514

φ5×10 (B Type)8×7×20

FVC10001570942347094631573.5242.54454418　　70248560

M8×1.25×1111104.5M86.8131664141973775

M6×1×126　　 Depth 7

6594.519

φ6×12 (B Type)8×7×32

G1/4 G1/4G1/8

FVC1600208211429882116801964302.557625610　　9030104.577

M10×1.5×1515136.5M108.51620849491305090

M8×1.25×168　　 Depth 9

82114.519

φ8×16 (B Type)10×8×45

(mm)External Dimensions and Machining Dimensions for Mounting

+ 0.027+ 0.005

+ 0.027+ 0.005

+ 0.027+ 0.005

+ 0.018 0

+ 0.022 0

+ 0.018 0

QR S

(15)

TN

M N

LSlider Stroke

The Center of the Workpiece

φD -0.1-0.2

AA

GClamping Height

FE

ABAC


８-V Screw

X±0.1 X±0.1

CJA

U±0.05

PG8

PG8

2-Parallel Pin (Included)

JH

Air Blow Port


O-ring 1BP7 (Included)


8-Y Through Tapped HoleφZ Hole

Slider

※1

※2

φ5

φJB

BA

W

WW


※2Lock Port：G Thread (Speed Control Valve Port)

Lever (Prepared by Customer)

Ｘ

K

★

★

FVC0630 has only fourholes marked with ★.★

★

External Dimensions※ The drawing shows the released state of FVC.


2-G Thread Plug

(Slot Width)

(Included)

6.3S

２

φD+ 0.3 0

AL or more

AL or more

30゜ 30゜6.3S2


8-φAM Through Hole

AG AGAF AF

AG AGAF AF

AH±0.01

X±0.1AH±0.01

X±0.1AH±0.01

X ±0.1AH±0.01

X ±0.1

Air Blow Port

８-AJ Screw

２-φAKH8２-φAKH8

φ5

φ5Air Blow Port

φ5

φ5

Lock Portφ5

Lock Port

WW W

ADAD

WW

ADAD

Release Port

AE±0.01AE±0.01

AE±0.01AE±0.01

(Mounting Bolt)

(Mounting Bolt)


W

φ5Release Port

φD+ 0.3 0

Notes: 1. Roughness of mounting surface should be 6.3S or better. 2. Install a lever on the top of the slider when in use. ※1. Mounting bolts are not provided with the product. Please prepare them according to the mounting height referring to dimension 'AB'. ※2. Speed control valve is sold separately. Please refer to P.891 for detail.

FVC0630 has only four holes marked with ★.

★

★

★

★

★

★

★

★



FVC0630 has only four screws marked with ★.


888

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVA/FVD/FVCCentering Vise　Cautions

● Installation Notes

1）Check the Usable Fluid

● Please use the appropriate fluid by referring to the Hydraulic Fluid List

(P.1237).

2） Filling the Grease

● Fill the grease from the grease nipple or lubrication port before use,

and operate the centering vise 2 or 3 times without a workpiece.

Use the grease of lithium soap thickened, mineral oil grease fortified

with MoS2. (Recommended Grease：MOLYKOTE® BR-2 PLUS made

by TORAY・DOW CORNING)

If too much grease is applied it may be overflowed from the gap of

body and slider during operation.

3) Installation/Removal of the Lever (Prepared by Customer)

● Use hexagon socket bolts for mounting (with tensile strength of 12.9)

and tighten them with the torque shown in the chart below. Installation

failure causes the deformaiton of lever and decrease of clamping force.

4）Mounting the Centering Vise

● When mounting the centering vise, use hexagon socket bolts as multiple

bolt holes for mounting (with tensile strength of 12.9) and tighten them

with the torque shown in the chart below. Tightening with greater torque

than recommended can depress the seating surface or break the bolt.

Tightening Torque (N･m)102550102550255080

Thread SizeM6×1M8×1.25M10×1.5M6×1M8×1.25M10×1.5M8×1.25M10×1.5M12×1.75

Model No.FVA0400FVA0630FVA1000FVC0630FVC1000FVC1600FVD1600FVD2500FVD4000

FVA

FVC

FVD

Tightening Torque (N･m)6.36.310101025102550

Thread SizeM5×0.8M5×0.8M6×1M6×1M6×1M8×1.25M6×1M8×1.25M10×1.5


FVA

FVC

FVD

<When Mounting from the Top>


Thread SizeM8×1.25M8×1.25M8×1.25M8×1.25M8×1.25M10×1.5M8×1.25M10×1.5M12×1.75


FVA

FVC

FVD

<When Mounting from the Bottom>

※ This drawing shows FVC.

Cautions

● Notes for Design

1）Check Specifications

● Please use each product according to the specifications.

2）Notes for Circuit Design

● Please read "Notes on Hydraulic Cylinder Speed Control Circuit" on

P.1238 to assist with proper hydraulic circuit designing.

● Ensure there is no possibility of supplying hydraulic pressure to the

lock and release ports simultaneously.

● Air blow passage should be φ6mm or more.

3）Continuously supply air pressure to the air blow port. (FVC Only)

● Continuously supply air pressure to the air blow port.

If air is shut off during operation foreign substance may enter into

the cylinder leading to malfunction.

4）Tightening depth of the lever mounting bolt must be less than the

maximum tightening depth. (FVC Only)

● Longer lever mounting bolt than the maximum tightening depth

causes tightening the body and slider leading to malfunction and

decrease of clamping force.

5）Do not apply impact on the lever (prepared by customer) when

loading a workpiece.

● Otherwise, it leads to malfunction or damage on the lever.

6）Clamp the workpiece at the center of the vise.

● Please contact us for available offset amount.

(No offset option for FVA/FVD. Offset is only available for FVC.)

7）Clamping in Opening Direction

● Clamping force curve in this catalog indicates the force in closing direction.

For clamping in opening direction as shown below, clamping force and

usable range are different. Please contact us for further information.

Max. Tightening Depth (mm)91115

Model No.FVC0630FVC1000FVC1600

Offset Amount

The Center of the Vise

Mountingfrom the Top

Mountingfrom the Bottom

5）Operating Speed Adjustment

● Excessive operating speed of the centering vise may lead to wear-

out or damage the intenal components. Please adjust the operating

speed so that the slider fully strokes within 1~2 seconds.

● Install a flow control valve and gradually control the flow rate from

the low-speed side (small flow) to the designated speed. Controlling

from the high-speed side (large flow) causes excessive surge pressure

or overload to the clamp leading to damage of a machine or device.

● When controlling the speed with the flow control valve, make sure

there is no excessively high pressure in the hydraulic circuit.

● Speed control may not be conducted if there is excessive air in the

hydraulic circuit.

● The viscosity of fluid will decrease when its temperature increases.

This will slow the operating speed of the centering vise.

Adjust the speed under the proper temperature condition.

Opening Direction

・ Installation Notes ・ Hydraulic Fluid List ・ Notes on Hydraulic Cylinder Speed Control Circuit・ Notes on Handling ・ Maintenance/Inspection ・ Warranty

※ Please refer to P.1237 for common cautions.

889

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Control Valve

BZLBZTBZX/JZG

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT





Model FVCModel No. IndicationSpecifications・External Dimensionsmodel FVA/FVD/FVCCentering Vise　Cautions

● Installation Notes


● Please use the appropriate fluid by referring to the Hydraulic Fluid List

(P.1237).

2） Filling the Grease

● Fill the grease from the grease nipple or lubrication port before use,

and operate the centering vise 2 or 3 times without a workpiece.

Use the grease of lithium soap thickened, mineral oil grease fortified

with MoS2. (Recommended Grease：MOLYKOTE® BR-2 PLUS made

by TORAY・DOW CORNING)

If too much grease is applied it may be overflowed from the gap of

body and slider during operation.

3) Installation/Removal of the Lever (Prepared by Customer)

● Use hexagon socket bolts for mounting (with tensile strength of 12.9)

and tighten them with the torque shown in the chart below. Installation

failure causes the deformaiton of lever and decrease of clamping force.

4）Mounting the Centering Vise

● When mounting the centering vise, use hexagon socket bolts as multiple

bolt holes for mounting (with tensile strength of 12.9) and tighten them

with the torque shown in the chart below. Tightening with greater torque

than recommended can depress the seating surface or break the bolt.


Thread SizeM6×1M8×1.25M10×1.5M6×1M8×1.25M10×1.5M8×1.25M10×1.5M12×1.75


FVA

FVC

FVD

Tightening Torque (N･m)6.36.310101025102550

Thread SizeM5×0.8M5×0.8M6×1M6×1M6×1M8×1.25M6×1M8×1.25M10×1.5


FVA

FVC

FVD

<When Mounting from the Top>


Thread SizeM8×1.25M8×1.25M8×1.25M8×1.25M8×1.25M10×1.5M8×1.25M10×1.5M12×1.75


FVA

FVC

FVD

<When Mounting from the Bottom>

※ This drawing shows FVC.

Cautions

● Notes for Design

1）Check Specifications

● Please use each product according to the specifications.

2）Notes for Circuit Design

● Please read "Notes on Hydraulic Cylinder Speed Control Circuit" on

P.1238 to assist with proper hydraulic circuit designing.

● Ensure there is no possibility of supplying hydraulic pressure to the

lock and release ports simultaneously.

● Air blow passage should be φ6mm or more.

3）Continuously supply air pressure to the air blow port. (FVC Only)

● Continuously supply air pressure to the air blow port.

If air is shut off during operation foreign substance may enter into

the cylinder leading to malfunction.

4）Tightening depth of the lever mounting bolt must be less than the

maximum tightening depth. (FVC Only)

● Longer lever mounting bolt than the maximum tightening depth

causes tightening the body and slider leading to malfunction and

decrease of clamping force.

5）Do not apply impact on the lever (prepared by customer) when

loading a workpiece.

● Otherwise, it leads to malfunction or damage on the lever.

6）Clamp the workpiece at the center of the vise.

● Please contact us for available offset amount.

(No offset option for FVA/FVD. Offset is only available for FVC.)

7）Clamping in Opening Direction

● Clamping force curve in this catalog indicates the force in closing direction.

For clamping in opening direction as shown below, clamping force and

usable range are different. Please contact us for further information.

Max. Tightening Depth (mm)91115

Model No.FVC0630FVC1000FVC1600

Offset Amount

The Center of the Vise

Mountingfrom the Top

Mountingfrom the Bottom

5）Operating Speed Adjustment

● Excessive operating speed of the centering vise may lead to wear-

out or damage the internal components. Please adjust the operating

speed so that the slider fully strokes within 1~2 seconds.

● Install a flow control valve and gradually control the flow rate from

the low-speed side (small flow) to the designated speed. Controlling

from the high-speed side (large flow) causes excessive surge pressure

or overload to the centering vise leading to damage of a machine or

device.

● When controlling the speed with the flow control valve, make sure

there is no excessively high pressure in the hydraulic circuit.

● Speed control may not be conducted if there is excessive air in the

hydraulic circuit.

● The viscosity of fluid will decrease when its temperature increases.

This will accelerate the operating speed of the centering vise.

Adjust the speed under the proper temperature condition.

Opening Direction

・ Installation Notes ・ Hydraulic Fluid List ・ Notes on Hydraulic Cylinder Speed Control Circuit・ Notes on Handling ・ Maintenance/Inspection ・ Warranty

※ Please refer to P.1237 for common cautions.

890

Notes on Hydraulic Cylinder Speed Control Circuit

Cautions

Installation Notes(For Hydraulic Series)

Hydraulic Fluid List

Notes on Handling

Maintenance/ Inspection

Warranty

Index

Search byAlphabetical Order

Company Profile

Sales Offices

Company Profile

Our Products

History

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Installation Notes(For Hydraulic Series)Installation Notes(For Hydraulic Series)

Notes on Hydraulic CylinderSpeed Control Circuit

Notes on Hydraulic CylinderSpeed Control Circuit Maintenance/Inspection WarrantyNotes on HandlingHydraulic Fluid ListHydraulic Fluid ListCautions

Cautions

● Installation Notes (For Hydraulic Series) ● Hydraulic Fluid List


● Please use the appropriate fluid by referring to the Hydraulic Fluid List.

2）Procedure before Piping

● The pipeline, piping connector and fixture circuits should be cleaned

by thorough flushing.

● The dust and cutting chips in the circuit may lead to fluid leakage

and malfunction.

● There is no filter provided with Kosmek’s product except for a part

of valves which prevents foreign materials and contaminants from

getting into the circuit.

3）Applying Sealing Tape

● Wrap with tape 1 to 2 times following the screw direction.

● Pieces of the sealing tape can lead to oil leakage and malfunction.

● In order to prevent a foreign substance from going into the product

during the piping work, it should be carefully cleaned before working.

4）Air Bleeding of the Hydraulic Circuit

● If the hydraulic circuit has excessive air, the action time may become

very long. If air enters the circuit after connecting the hydraulic port

or under the condition of no air in the oil tank, please perform

the following steps.

① Reduce hydraulic pressure to less than 2MPa.

② Loosen the cap nut of pipe fitting closest to the clamp by one full turn.

③ Wiggle the pipeline to loosen the outlet of pipe fitting.

Hydraulic fluid mixed with air comes out.

④ Tighten the cap nut after bleeding.

⑤ It is more effective to bleed air at the highest point inside the circuit

or at the end of the circuit.

(Set an air bleeding valve at the highest point inside the circuit.)

5）Checking Looseness and Retightening

● At the beginning of the machine installation, the bolt and nut may

be tightened lightly. Check the looseness and re-tighten as required.

Showa Shell SekiyuIdemitsu KosanJX Nippon Oil & EnergyCosmo OilExxonMobilMatsumura OilCastrol

Maker Anti-Wear Hydraulic OilTellus S2 M 32

Daphne Hydraulic Fluid 32Super Hyrando 32Cosmo Hydro AW32Mobil DTE 24Hydol AW-32Hyspin AWS 32

Multi-Purpose Hydraulic OilMorlina S2 B 32

Daphne Super Multi Oil 32Super Mulpus DX 32Cosmo New Mighty Super 32Mobil DTE 24 Light

Note As it may be difficult to purchase the products as shown in the table from overseas, please contact the respective manufacturer.

ISO Viscosity Grade ISO-VG-32

Flow Control at the Release Side

Ｗ

Flow Control Valve(Any location is OK)

Sequence Valve

● Notes on Hydraulic Cylinder Speed Control Unit

Please pay attention to the cautions below. Design the hydraulic circuit for controlling the action speed of hydraulic cylinder.

Improper circuit design may lead to malfunctions and damages. Please review the circuit design in advance.！ ● Flow Control Circuit for Single Acting Cylinder For spring return single acting cylinders, restricting flow during release can extremely slow down or disrupt release action. The preferred method is to control the flow during the lock action using a valve that has free-flow in the release direction. It is also preferred to provide a flow control valve at each actuator.

Accelerated clamping speed by excessive hydraulic flow to the cylinder may sustain damage. In this case add flow control to regulate flow. (Please add flow control to release flow if the lever weight is put on at the time of release action when using swing clamps.)

● Flow Control Circuit for Double Acting Cylinder Flow control circuit for double acting cylinder should have meter-out circuits for both the lock and release sides. Meter-in control can have adverse effect by presence of air in the system. However, in the case of controlling LKE, TMA, TLA, both lock side

and release side should be meter-in circuit.

Refer to P.75 for speed adjustment of LKE.

For TMA and TLA, if meter-out circuit is used, abnormal high

pressure is created, which causes oil leakage and damage.

　　【Meter-out Circuit】 (Except LKE/TMA/TLA)

　　

【Meter-in Circuit】 (LKE/TMA/TLA must be controlled with meter-in.)

In the case of meter-out circuit, the hydraulic circuit should be designed with the following points. ① Single acting components should not be used in the same flow control circuit as the double acting components. The release action of the single acting cylinders may become erratic or very slow.

Refer to the following circuit when both the single acting cylinder and double acting cylinder are used together. ○ Separate the control circuit.

○ Reduce the influence of double acting cylinder control unit. However, due to the back pressure in tank line, single action cylinder is activated after double action cylinder works.

② In the case of meter-out circuit, the inner circuit pressure may increase during the cylinder action because of the fluid supply. The increase of the inner circuit pressure can be prevented by reducing the supplied fluid beforehand via the flow control valve. Especially when using sequence valve or pressure switches for clamping detection. If the back pressure is more than the set pressure then the system will not work as it is designed to.

1237


Cautions



Notes on Handling


Warranty

Index


Company Profile

Sales Offices

Company Profile

Our Products

History

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Installation Notes(For Hydraulic Series)Installation Notes(For Hydraulic Series)

Notes on Hydraulic CylinderSpeed Control Circuit

Notes on Hydraulic CylinderSpeed Control Circuit Maintenance/Inspection WarrantyNotes on HandlingHydraulic Fluid ListHydraulic Fluid ListCautions

Cautions

● Installation Notes (For Hydraulic Series) ● Hydraulic Fluid List


● Please use the appropriate fluid by referring to the Hydraulic Fluid List.

2）Procedure before Piping

● The pipeline, piping connector and fixture circuits should be cleaned

by thorough flushing.

● The dust and cutting chips in the circuit may lead to fluid leakage

and malfunction.

● There is no filter provided with Kosmek’s product except for a part

of valves which prevents foreign materials and contaminants from

getting into the circuit.

3）Applying Sealing Tape

● Wrap with tape 1 to 2 times following the screw direction.

● Pieces of the sealing tape can lead to oil leakage and malfunction.

● In order to prevent a foreign substance from going into the product

during the piping work, it should be carefully cleaned before working.

4）Air Bleeding of the Hydraulic Circuit

● If the hydraulic circuit has excessive air, the action time may become

very long. If air enters the circuit after connecting the hydraulic port

or under the condition of no air in the oil tank, please perform

the following steps.

① Reduce hydraulic pressure to less than 2MPa.

② Loosen the cap nut of pipe fitting closest to the clamp by one full turn.

③ Wiggle the pipeline to loosen the outlet of pipe fitting.

Hydraulic fluid mixed with air comes out.

④ Tighten the cap nut after bleeding.

⑤ It is more effective to bleed air at the highest point inside the circuit

or at the end of the circuit.

(Set an air bleeding valve at the highest point inside the circuit.)

5）Checking Looseness and Retightening

● At the beginning of the machine installation, the bolt and nut may

be tightened lightly. Check the looseness and re-tighten as required.

Showa Shell SekiyuIdemitsu KosanJX Nippon Oil & EnergyCosmo OilExxonMobilMatsumura OilCastrol

Maker Anti-Wear Hydraulic OilTellus S2 M 32

Daphne Hydraulic Fluid 32Super Hyrando 32Cosmo Hydro AW32Mobil DTE 24Hydol AW-32Hyspin AWS 32

Multi-Purpose Hydraulic OilMorlina S2 B 32

Daphne Super Multi Oil 32Super Mulpus DX 32Cosmo New Mighty Super 32Mobil DTE 24 Light

Note As it may be difficult to purchase the products as shown in the table from overseas, please contact the respective manufacturer.

ISO Viscosity Grade ISO-VG-32

Flow Control at the Release Side

Ｗ

Flow Control Valve(Any location is OK)

Sequence Valve

● Notes on Hydraulic Cylinder Speed Control Unit

Please pay attention to the cautions below. Design the hydraulic circuit for controlling the action speed of hydraulic cylinder.

Improper circuit design may lead to malfunctions and damages. Please review the circuit design in advance.！ ● Flow Control Circuit for Single Acting Cylinder For spring return single acting cylinders, restricting flow during release can extremely slow down or disrupt release action. The preferred method is to control the flow during the lock action using a valve that has free-flow in the release direction. It is also preferred to provide a flow control valve at each actuator.

Accelerated clamping speed by excessive hydraulic flow to the cylinder may sustain damage. In this case add flow control to regulate flow. (Please add flow control to release flow if the lever weight is put on at the time of release action when using swing clamps.)

● Flow Control Circuit for Double Acting Cylinder Flow control circuit for double acting cylinder should have meter-out circuits for both the lock and release sides. Meter-in control can have adverse effect by presence of air in the system. However, in the case of controlling LKE, TMA, TLA, both lock side

and release side should be meter-in circuit.

Refer to P.75 for speed adjustment of LKE.

For TMA and TLA, if meter-out circuit is used, abnormal high

pressure is created, which causes oil leakage and damage.

　　【Meter-out Circuit】 (Except LKE/TMA/TLA)

　　

【Meter-in Circuit】 (LKE/TMA/TLA must be controlled with meter-in.)

In the case of meter-out circuit, the hydraulic circuit should be designed with the following points. ① Single acting components should not be used in the same flow control circuit as the double acting components. The release action of the single acting cylinders may become erratic or very slow.

Refer to the following circuit when both the single acting cylinder and double acting cylinder are used together. ○ Separate the control circuit.

○ Reduce the influence of double acting cylinder control unit. However, due to the back pressure in tank line, single action cylinder is activated after double action cylinder works.

② In the case of meter-out circuit, the inner circuit pressure may increase during the cylinder action because of the fluid supply. The increase of the inner circuit pressure can be prevented by reducing the supplied fluid beforehand via the flow control valve. Especially when using sequence valve or pressure switches for clamping detection. If the back pressure is more than the set pressure then the system will not work as it is designed to.

1238


Cautions



Notes on Handling


Warranty

Index


Company Profile

Sales Offices

Company Profile

Our Products

History

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries



Notes on Hydraulic CylinderSpeed Control Circuit Maintenance/InspectionMaintenance/Inspection WarrantyWarrantyNotes on HandlingNotes on HandlingHydraulic Fluid ListCautions

1）Warranty Period

● The product warranty period is 18 months from shipment from

our factory or 12 months from initial use, whichever is earlier.

2）Warranty Scope

● If the product is damaged or malfunctions during the warranty

period due to faulty design, materials or workmanship, we will

replace or repair the defective part at our expense.

Defects or failures caused by the following are not covered.

① If the stipulated maintenance and inspection are not carried out.

② If the product is used while it is not suitable for use based on

the operator’s judgment, resulting in defect.

③ If it is used or handled in inappropriate way by the operator.

（Including damage caused by the misconduct of the third party.）

④ If the defect is caused by reasons other than our responsibility.

⑤ If repair or modifications are carried out by anyone other than Kosmek,

or without our approval and confirmation, it will void warranty.

⑥ Other caused by natural disasters or calamities not attributable to

our company.

⑦ Parts or replacement expenses due to parts consumption and

deterioration.

(Such as rubber, plastic, seal material and some electric components.)

Damages excluding from direct result of a product defect shall be

excluded from the warranty.

● Warranty

Cautions

1）It should be handled by qualified personnel.

● The hydraulic machine and air compressor should be handled

and maintained by qualified personnel.

2）Do not handle or remove the machine unless the safety protocols

are ensured.

① The machine and equipment can only be inspected or prepared

when it is confirmed that the preventive devices are in place.

② Before the machine is removed, make sure that the above-mentioned

safety measures are in place. Shut off the air of hydraulic source

and make sure no pressure exists in the hydraulic and air circuit.

③ After stopping the machine, do not remove until the temperature

cools down.

④ Make sure there is no abnormality in the bolts and respective parts

before restarting the machine or equipment.

3）Do not touch clamp (cylinder) while clamp (cylinder) is working.

Otherwise, your hands may be injured due to clinching.

4）Do not disassemble or modify.

● If the equipment is taken apart or modified, the warranty will be

voided even within the warranty period.

1）Removal of the Machine and Shut-off of Pressure Source

● Before the machine is removed, make sure that the

above-mentioned safety measures are in place. Shut off the

air of hydraulic source and make sure no pressure exists in

the hydraulic and air circuit.

● Make sure there is no abnormality in the bolts and respective

parts before restarting.

2）Regularly clean the area around the piston rod and plunger.

● If it is used when the surface is contaminated with dirt, it may

lead to packing seal damage, malfunctioning, fluid leakage

and air leaks.

3） Please clean out the reference surface regularly (taper reference

surface and seating surface) of locating machine. (VS/VT/VFL/

VFM/VFJ/VFK/WVS/VWM/VWK/VX/VXF)

● Location products, except VX/VXF model, can remove

contaminants with cleaning functions.

When installing pallets makes sure there is no thick sludge like

substances on pallets.

● Continuous use with dirt on components will lead to locating

functions not work properly, leaking and malfunction.

4） If disconnecting by couplers on a regular basis, air bleeding

should be carried out daily to avoid air mixed in the circuit.

5）Regularly tighten nuts, bolts, pins, cylinders and pipe line to

ensure proper use.

6）Make sure the hydraulic fluid has not deteriorated.

7）Make sure there is smooth action and no abnormal noise.

● Especially when it is restarted after left unused for a long

period, make sure it can be operated correctly.

8）The products should be stored in the cool and dark place

without direct sunshine or moisture.

9）Please contact us for overhaul and repair.

● Notes on Handling ● Maintenance and Inspection

1239


Cautions



Notes on Handling


Warranty

Index


Company Profile

Sales Offices

Company Profile

Our Products

History

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries



Notes on Hydraulic CylinderSpeed Control Circuit Maintenance/InspectionMaintenance/Inspection WarrantyWarrantyNotes on HandlingNotes on HandlingHydraulic Fluid ListCautions

1）Warranty Period

● The product warranty period is 18 months from shipment from

our factory or 12 months from initial use, whichever is earlier.

2）Warranty Scope

● If the product is damaged or malfunctions during the warranty

period due to faulty design, materials or workmanship, we will

replace or repair the defective part at our expense.

Defects or failures caused by the following are not covered.

① If the stipulated maintenance and inspection are not carried out.

② If the product is used while it is not suitable for use based on

the operator’s judgment, resulting in defect.

③ If it is used or handled in inappropriate way by the operator.

（Including damage caused by the misconduct of the third party.）

④ If the defect is caused by reasons other than our responsibility.

⑤ If repair or modifications are carried out by anyone other than Kosmek,

or without our approval and confirmation, it will void warranty.

⑥ Other caused by natural disasters or calamities not attributable to

our company.

⑦ Parts or replacement expenses due to parts consumption and

deterioration.

(Such as rubber, plastic, seal material and some electric components.)

Damages excluding from direct result of a product defect shall be

excluded from the warranty.

● Warranty

Cautions

1）It should be handled by qualified personnel.

● The hydraulic machine and air compressor should be handled

and maintained by qualified personnel.

2）Do not handle or remove the machine unless the safety protocols

are ensured.

① The machine and equipment can only be inspected or prepared

when it is confirmed that the preventive devices are in place.

② Before the machine is removed, make sure that the above-mentioned

safety measures are in place. Shut off the air of hydraulic source

and make sure no pressure exists in the hydraulic and air circuit.

③ After stopping the machine, do not remove until the temperature

cools down.

④ Make sure there is no abnormality in the bolts and respective parts

before restarting the machine or equipment.

3）Do not touch clamp (cylinder) while clamp (cylinder) is working.

Otherwise, your hands may be injured due to clinching.

4）Do not disassemble or modify.

● If the equipment is taken apart or modified, the warranty will be

voided even within the warranty period.

1）Removal of the Machine and Shut-off of Pressure Source

● Before the machine is removed, make sure that the

above-mentioned safety measures are in place. Shut off the

air of hydraulic source and make sure no pressure exists in

the hydraulic and air circuit.

● Make sure there is no abnormality in the bolts and respective

parts before restarting.

2）Regularly clean the area around the piston rod and plunger.

● If it is used when the surface is contaminated with dirt, it may

lead to packing seal damage, malfunctioning, fluid leakage

and air leaks.

3） Please clean out the reference surface regularly (taper reference

surface and seating surface) of locating machine. (VS/VT/VFL/

VFM/VFJ/VFK/WVS/VWM/VWK/VX/VXF)

● Location products, except VX/VXF model, can remove

contaminants with cleaning functions.

When installing pallets makes sure there is no thick sludge like

substances on pallets.

● Continuous use with dirt on components will lead to locating

functions not work properly, leaking and malfunction.

4） If disconnecting by couplers on a regular basis, air bleeding

should be carried out daily to avoid air mixed in the circuit.

5）Regularly tighten nuts, bolts, pins, cylinders and pipe line to

ensure proper use.

6）Make sure the hydraulic fluid has not deteriorated.

7）Make sure there is smooth action and no abnormal noise.

● Especially when it is restarted after left unused for a long

period, make sure it can be operated correctly.

8）The products should be stored in the cool and dark place

without direct sunshine or moisture.

9）Please contact us for overhaul and repair.

● Notes on Handling ● Maintenance and Inspection

1240

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest

Model BZLModel BZTModel BZXModel JZG

Directly mounted to clamps, flow control valve・Air bleeding・plug

Control Valve

Model BZL

Speed Control Valve（For Low Pressure）

OperatingPressure Range Action Description

7MPa or less

Model BZL

Model BZT

Speed Control Valve

Model BZX

Air Bleed Valve

Model JZG

G Thread Plug

Flow control valve, air bleeding valve, G-thread plug for

G-thread (-C option) directly mounted.

Directly mounted to clamps

Lock NutAdjusting Screw

G Thread Plug

Adjust the f low by wrench.

It can adjust the clamping action speed individually.

Flow Control

Air bleeding in the circuit is possible

by loosening f low control valve.

Air bleeding in the circuit is possible by wrench.


by loosening G thread plug.

35MPa or less

25MPa or less

35MPa or less

Model BZT

Speed Control Valve（For High Pressure）

Model BZX

Air Bleed Valve

Model JZG

G Thread Plug

Speed Control Valve

Clamps→ P.893

→ P.897

→ P.899

→ P.901

891

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest

Model BZLModel BZTModel BZXModel JZG

Directly mounted to clamps, flow control valve・Air bleeding・plug

Control Valve

Model BZL

Speed Control Valve（For Low Pressure）

OperatingPressure Range Action Description

7MPa or less

Model BZL

Model BZT

Speed Control Valve

Model BZX

Air Bleed Valve

Model JZG

G Thread Plug

Flow control valve, air bleeding valve, G-thread plug for

G-thread (-C option) directly mounted.

Directly mounted to clamps

Lock NutAdjusting Screw

G Thread Plug

Adjust the f low by wrench.

It can adjust the clamping action speed individually.

Flow Control


by loosening f low control valve.

Air bleeding in the circuit is possible by wrench.


by loosening G thread plug.

35MPa or less

25MPa or less

35MPa or less

Model BZT

Speed Control Valve（For High Pressure）

Model BZX

Air Bleed Valve

Model JZG

G Thread Plug

Speed Control Valve

Clamps→ P.893

→ P.897

→ P.899

→ P.901

892

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest

Model No.IndicationModel No.Indication SpecificationsSpecifications External

DimensionsFlow Rate GraphApplicableProductsApplicableProductsControl Valve　Speed Control Valve (For Low Pressure) model BZL

Specifications

MPaMPa

MPamm2

℃N･m

BZL0100-A

G1/8A

2.6

10

BZL0200-A

Meter-inG1/4A0.045.0

25

710.5

General Hydraulic Oil Equivalent to ISO-VG-320 ～ 70

BZL0300-A

G3/8A

11.6

35

BZL0100-B

G1/8A

2.6

10

BZL0200-B

Meter-outG1/4A0.125.0

25

BZL0300-B

G3/8A

10.2

35

Model No.Max. Operating PressureWithstanding PressureControl MethodG Thread SizeCracking PressureMax. Passage AreaUsable FluidOperating Temperature Tightening Torque for Main Body

Notes : 1. Minimum passage area when fully opened is the same as the maximum passage area in the table above. 2. It must be mounted with recommended torque. Because of the structure of the metal seal, if mounting torque is insufficient, the flow control valve may not be able to adjust the flow rate. 3. Don’t use used BZL to other clamps. Flow control will not be made because the bottom depth difference of G thread makes metal seal insufficient.

Model No. Indication (Speed Control Valve for Low Pressure)

1 2 3

BZL 0 10 0 - B

2

1 G Thread Size

10 ： Thread Part G1/8A Thread




Design No.

3 Control Method

A ： Meter-in

B ： Meter-out

P1 portHydraulic PressureSupply Side

P2 PortClamp Side

Circuit Symbol：Meter-in

Thread Part


P2 PortClamp Side

Circuit Symbol：Meter-out

A B

Applicable Products

Note : 1. Flow control circuit for double action cylinder should have meter-out circuits for both the lock and release sides (except model LKE/TLA/TMA). Meter-in circuits can be adversely affected by any air in the system.

LC (Single Action)Work SupportLC0262-C□LC0302-C□LC0362-C□LC0402-C□□-□LC0482-C□□-□LC0552-C□□-□LC0652-C□□-□

LC0752-C□□-□LC0902-C□□-□

DBC (Double Action)Block Cylinder(DBC0250-C□)(DBC0320-C□)

DBC0250-C□DBC0320-C□

(DBC0400-C□)(DBC0500-C□)DBC0400-C□DBC0500-C□

FVA (Double Action)Centering Vise(FVA0400)(FVA0630)(FVA1000)

FVA0400FVA0630FVA1000

FVC (Double Action)Centering Vise(FVC0630)

FVC0630

(FVC1000)(FVC1600)FVC1000FVC1600

FVD (Double Action)Centering Vise(FVD1600)(FVD2500)

FVD1600FVD2500

(FVD4000)

FVD4000

DBA (Double Action)Block Cylinder(DBA0250-C□)(DBA0320-C□)

DBA0250-C□DBA0320-C□

(DBA0400-C□)(DBA0500-C□)DBA0400-C□DBA0500-C□

Model No.

BZL0100-A

BZL0100-B

BZL0200-A

BZL0200-B

BZL0300-A

BZL0300-B

LHA (Double Action)Swing Clamp(LHA0360-C□□-□)(LHA0400-C□□-□)(LHA0480-C□□-□)(LHA0550-C□□-□)

LHA0360-C□□-□LHA0400-C□□-□LHA0480-C□□-□LHA0550-C□□-□

(LHA0650-C□□-□)(LHA0750-C□□-□)LHA0650-C□□-□LHA0750-C□□-□(LHA0900-C□□-□)(LHA1050-C□□-□)LHA0900-C□□-□LHA1050-C□□-□

LHC (Double Action)Swing Clamp(LHC0360-C□□-□)(LHC0400-C□□-□)(LHC0480-C□□-□)(LHC0550-C□□-□)

LHC0360-C□□-□LHC0400-C□□-□LHC0480-C□□-□LHC0550-C□□-□

(LHC0650-C□□-□)

LHC0650-C□□-□

Model No.

BZL0100-A

BZL0100-B

BZL0200-A

BZL0200-B

BZL0300-A

BZL0300-B

LKE (Double Action)High-Power Link ClampLKE0300-C□LKE0360-C□LKE0400-C□LKE0480-C□LKE0550-C□

LKC (Double Action)Link Clamp

（LKC0400-C□-□）（LKC0480-C□-□）（LKC0550-C□-□）

LKC0400-C□-□LKC0480-C□-□LKC0550-C□-□

(LKC0650-C□-□)

LKC0650-C□-□

LKA (Double Action)Link Clamp

（LKA0360-C□□-□）（LKA0400-C□□-□）（LKA0480-C□□-□）（LKA0550-C□□-□）

LKA0360-C□□-□LKA0400-C□□-□LKA0480-C□□-□LKA0550-C□□-□

（LKA0650-C□□-□）（LKA0750-C□□-□）LKA0650-C□□-□LKA0750-C□□-□（LKA0900-C□□-□）（LKA1050-C□□-□）LKA0900-C□□-□LKA1050-C□□-□

LT (Single Action)Swing ClampLT0301-C□-□LT036□-C□-□LT040□-C□-□LT048□-C□-□LT055□-C□-□

LT065□-C□-□LT075□-C□-□

LG (Single Action)Swing ClampLG0301-C□-□LG036□-C□-□LG040□-C□-□LG048□-C□-□LG055□-C□-□

LG065□-C□-□LG075□-C□-□

LG090□-C□-□LG105□-C□-□

Model No.

BZL0100-A

BZL0100-B

BZL0200-A

BZL0200-B

BZL0300-A

BZL0300-B

LL (Double Action)Linear Cylinder（ LL0360-C□□-□ ）（ LL0400-C□□-□ ）（ LL0480-C□□-□ ）（ LL0550-C□□-□ ）

LL0360-C□□-□LL0400-C□□-□LL0480-C□□-□LL0550-C□□-□

（ LL0650-C□□-□ ）（ LL0750-C□□-□ ）LL0650-C□□-□LL0750-C□□-□

（ LL0900-C□□-□ ）（ LL1050-C□□-□ ）LL0900-C□□-□LL1050-C□□-□

LLR (Double Action)Linear Cylinder（LLR0360-C□□-□-□）（LLR0400-C□□-□-□）（LLR0480-C□□-□-□）（LLR0550-C□□-□-□）

LLR0360-C□□-□-□LLR0400-C□□-□-□LLR0480-C□□-□-□LLR0550-C□□-□-□（LLR0650-C□□-□-□）（LLR0750-C□□-□-□）LLR0650-C□□-□-□LLR0750-C□□-□-□

（LLR0900-C□□-□-□）（LLR1050-C□□-□-□）LLR0900-C□□-□-□LLR1050-C□□-□-□

LLW (Double Action)Lift Cylinder

（LLW036□-C□□-□）（LLW040□-C□□-□）（LLW048□-C□□-□）

LLW036□-C□□-□LLW040□-C□□-□LLW048□-C□□-□

LKW (Double Action)Link Clamp

（LKW040□-C□□-□）（LKW048□-C□□-□）（LKW055□-C□□-□）

LKW040□-C□□-□LKW048□-C□□-□LKW055□-C□□-□

（LKW065□-C□□-□）（LKW0751-C□□-□）LKW065□-C□□-□LKW0751-C□□-□

LM (Single Action)Link ClampLM0300-C□LM0360-C□LM0400-C□LM0480-C□LM0550-C□

LM0650-C□LM0750-C□

LJ (Single Action)Link ClampLJ0302-C□LJ0362-C□LJ0402-C□LJ0482-C□LJ0552-C□

LM0652-C□LM0752-C□

LJ0902-C□LJ1052-C□

LHS (Double Action)Swing Clamp

（LHS0360-C□□-□）（LHS0400-C□□-□）（LHS0480-C□□-□）（LHS0550-C□□-□）

LHS0360-C□□-□LHS0400-C□□-□LHS0480-C□□-□LHS0550-C□□-□

（LHS0650-C□□-□）（LHS0750-C□□-□）LHS0650-C□□-□LHS0750-C□□-□（LHS0900-C□□-□）（LHS1050-C□□-□）LHS0900-C□□-□LHS1050-C□□-□

LHE (Double Action)High-Power Swing Clamp

LHE0300-C□LHE0360-C□LHE0400-C□LHE0480-C□LHE0550-C□

LHW (Double Action)Swing Clamp(LHW040□-C□□-□)(LHW048□-C□□-□)(LHW055□-C□□-□)

LHW040□-C□□-□LHW048□-C□□-□LHW055□-C□□-□

(LHW065□-C□□-□)(LHW0751-C□□-□)LHW065□-C□□-□LHW0751-C□□-□

893

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest

Model No.IndicationModel No.Indication SpecificationsSpecifications External

DimensionsFlow Rate GraphApplicableProductsApplicableProductsControl Valve　Speed Control Valve (For Low Pressure) model BZL

Specifications

MPaMPa

MPamm2

℃N･m

BZL0100-A

G1/8A

2.6

10

BZL0200-A

Meter-inG1/4A0.045.0

25

710.5


BZL0300-A

G3/8A

11.6

35

BZL0100-B

G1/8A

2.6

10

BZL0200-B

Meter-outG1/4A0.125.0

25

BZL0300-B

G3/8A

10.2

35

Model No.Max. Operating PressureWithstanding PressureControl MethodG Thread SizeCracking PressureMax. Passage AreaUsable FluidOperating Temperature Tightening Torque for Main Body

Notes : 1. Minimum passage area when fully opened is the same as the maximum passage area in the table above. 2. It must be mounted with recommended torque. Because of the structure of the metal seal, if mounting torque is insufficient, the flow control valve may not be able to adjust the flow rate. 3. Don’t use used BZL to other clamps. Flow control will not be made because the bottom depth difference of G thread makes metal seal insufficient.

Model No. Indication (Speed Control Valve for Low Pressure)

1 2 3

BZL 0 10 0 - B

2

1 G Thread Size





Design No.

3 Control Method

A ： Meter-in

B ： Meter-out


P2 PortClamp Side

Circuit Symbol：Meter-in

Thread Part


P2 PortClamp Side

Circuit Symbol：Meter-out

A B

Applicable Products

Note : 1. Flow control circuit for double action cylinder should have meter-out circuits for both the lock and release sides (except model LKE/TLA/TMA). Meter-in circuits can be adversely affected by any air in the system.

LC (Single Action)Work SupportLC0262-C□LC0302-C□LC0362-C□LC0402-C□□-□LC0482-C□□-□LC0552-C□□-□LC0652-C□□-□

LC0752-C□□-□LC0902-C□□-□

DBC (Double Action)Block Cylinder(DBC0250-C□)(DBC0320-C□)


(DBC0400-C□)(DBC0500-C□)DBC0400-C□DBC0500-C□

FVA (Double Action)Centering Vise(FVA0400)(FVA0630)(FVA1000)

FVA0400FVA0630FVA1000

FVC (Double Action)Centering Vise(FVC0630)

FVC0630

(FVC1000)(FVC1600)FVC1000FVC1600

FVD (Double Action)Centering Vise(FVD1600)(FVD2500)

FVD1600FVD2500

(FVD4000)

FVD4000

DBA (Double Action)Block Cylinder(DBA0250-C□)(DBA0320-C□)


(DBA0400-C□)(DBA0500-C□)DBA0400-C□DBA0500-C□

Model No.

BZL0100-A

BZL0100-B

BZL0200-A

BZL0200-B

BZL0300-A

BZL0300-B

LHA (Double Action)Swing Clamp(LHA0360-C□□-□)(LHA0400-C□□-□)(LHA0480-C□□-□)(LHA0550-C□□-□)


(LHA0650-C□□-□)(LHA0750-C□□-□)LHA0650-C□□-□LHA0750-C□□-□(LHA0900-C□□-□)(LHA1050-C□□-□)LHA0900-C□□-□LHA1050-C□□-□

LHC (Double Action)Swing Clamp(LHC0360-C□□-□)(LHC0400-C□□-□)(LHC0480-C□□-□)(LHC0550-C□□-□)

LHC0360-C□□-□LHC0400-C□□-□LHC0480-C□□-□LHC0550-C□□-□

(LHC0650-C□□-□)

LHC0650-C□□-□

Model No.

BZL0100-A

BZL0100-B

BZL0200-A

BZL0200-B

BZL0300-A

BZL0300-B


LKC (Double Action)Link Clamp

（LKC0400-C□-□）（LKC0480-C□-□）（LKC0550-C□-□）

LKC0400-C□-□LKC0480-C□-□LKC0550-C□-□

(LKC0650-C□-□)

LKC0650-C□-□

LKA (Double Action)Link Clamp

（LKA0360-C□□-□）（LKA0400-C□□-□）（LKA0480-C□□-□）（LKA0550-C□□-□）


（LKA0650-C□□-□）（LKA0750-C□□-□）LKA0650-C□□-□LKA0750-C□□-□（LKA0900-C□□-□）（LKA1050-C□□-□）LKA0900-C□□-□LKA1050-C□□-□


LT065□-C□-□LT075□-C□-□


LG065□-C□-□LG075□-C□-□

LG090□-C□-□LG105□-C□-□

Model No.

BZL0100-A

BZL0100-B

BZL0200-A

BZL0200-B

BZL0300-A

BZL0300-B

LL (Double Action)Linear Cylinder（ LL0360-C□□-□ ）（ LL0400-C□□-□ ）（ LL0480-C□□-□ ）（ LL0550-C□□-□ ）

LL0360-C□□-□LL0400-C□□-□LL0480-C□□-□LL0550-C□□-□

（ LL0650-C□□-□ ）（ LL0750-C□□-□ ）LL0650-C□□-□LL0750-C□□-□

（ LL0900-C□□-□ ）（ LL1050-C□□-□ ）LL0900-C□□-□LL1050-C□□-□

LLR (Double Action)Linear Cylinder（LLR0360-C□□-□-□）（LLR0400-C□□-□-□）（LLR0480-C□□-□-□）（LLR0550-C□□-□-□）

LLR0360-C□□-□-□LLR0400-C□□-□-□LLR0480-C□□-□-□LLR0550-C□□-□-□（LLR0650-C□□-□-□）（LLR0750-C□□-□-□）LLR0650-C□□-□-□LLR0750-C□□-□-□

（LLR0900-C□□-□-□）（LLR1050-C□□-□-□）LLR0900-C□□-□-□LLR1050-C□□-□-□

LLW (Double Action)Lift Cylinder

（LLW036□-C□□-□）（LLW040□-C□□-□）（LLW048□-C□□-□）

LLW036□-C□□-□LLW040□-C□□-□LLW048□-C□□-□


（LKW040□-C□□-□）（LKW048□-C□□-□）（LKW055□-C□□-□）

LKW040□-C□□-□LKW048□-C□□-□LKW055□-C□□-□

（LKW065□-C□□-□）（LKW0751-C□□-□）LKW065□-C□□-□LKW0751-C□□-□

LM (Single Action)Link ClampLM0300-C□LM0360-C□LM0400-C□LM0480-C□LM0550-C□

LM0650-C□LM0750-C□

LJ (Single Action)Link ClampLJ0302-C□LJ0362-C□LJ0402-C□LJ0482-C□LJ0552-C□

LM0652-C□LM0752-C□

LJ0902-C□LJ1052-C□

LHS (Double Action)Swing Clamp

（LHS0360-C□□-□）（LHS0400-C□□-□）（LHS0480-C□□-□）（LHS0550-C□□-□）


（LHS0650-C□□-□）（LHS0750-C□□-□）LHS0650-C□□-□LHS0750-C□□-□（LHS0900-C□□-□）（LHS1050-C□□-□）LHS0900-C□□-□LHS1050-C□□-□

LHE (Double Action)High-Power Swing Clamp

LHE0300-C□LHE0360-C□LHE0400-C□LHE0480-C□LHE0550-C□

LHW (Double Action)Swing Clamp(LHW040□-C□□-□)(LHW048□-C□□-□)(LHW055□-C□□-□)

LHW040□-C□□-□LHW048□-C□□-□LHW055□-C□□-□

(LHW065□-C□□-□)(LHW0751-C□□-□)LHW065□-C□□-□LHW0751-C□□-□

894

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest

Model No.Indication Specifications External

DimensionsExternalDimensionsFlow Rate GraphFlow Rate GraphApplicable

ProductsControl Valve　Speed Control Valve (For Low Pressure) model BZL

External Dimensions


Model No.ABCDEFGHJKL

M (Nominal×Pitch)NPQ

R (Flat Surface Area)STUVW

BZL0100-□ BZL0200-□ BZL0300-□ 14 18 22 15.5 20 24 15 16 19 12 13 16 8.5 9.5 11 (11.6) (15.1) (17.6) G1/8 G1/4 G3/8 3 3 3 3.5 3.5 5 10 10 13 3 3 4 M6×0.75 M6×0.75 M8×0.75 11.5 15 17.5 8.5 11※1 13 9 11.5 13 16 20.5 24.5 10 13.5 17 8.7 11.5 15 G1/8 G1/4 G3/8 2 ～ 3 3 ～ 4 4 ～ 5 2.5 ～ 5 3.5 ～ 7 4.5 ～ 9

Notes : 1. Since the area is sealing part, be careful not to damage it. 2. Since the area is the metal sealing part of BZL, be careful not to damage it. (Especially when deburring) 3. No cutting chips or burr should be at the tolerance part of machining hole. 4. As shown in the drawing, P1 port is used as the hydraulic supply and P2 port as the clamp side. 5. If mounting plugs or fittings with G thread specification available in the market, the dimension '※1' should be 12.5.

Adjusting Screw

0.2

45°

0.4

BZL0□00

-□

(Clamp/Cylinder)

G ThreadExclusive Packing(Included)

P2 PortClamp Side

Fmax.H

max.CDEJ

φB

Hex. Socket L

M Screw

Hexagon KHexagon A

φT

max.φS

min.φR

φVQ

P1 PortHydraulic PressureSupply Side

φW

P2 PortClamp Side

U Thread(Prepared HoleφTFlat Bottom)

min.PNZ

Z⊥ 0.1

Attention 0- 0.10

OPENCLOSE

P1 PortHydraulic PressureSupply Side (mm)

Notes 1. Please read "Notes on Hydraulic Cylinder Speed Control Circuit" to assist with proper hydraulic circuit design.

If there is something wrong with the circuit design, it leads to the applications malfunction and damage. (Refer to P.1238)

2. It is dangerous to air bleed during operation under high pressure. It must be done under lower pressure.

(For reference: the minimum operating range of the product within the circuit.)

Free Flowing Direction

0

2

4

6

8

10

10 2 3 4 5 6Pressure Loss (MPa)

Flow Rate (L/min)

Controlled Flow Direction

0

2

4

6

8

10

10 2 3 4←Closed　Number of Turns of Adjusting Screw　Opened→

Flow Rate (L/min)


0

5

15

10

20

30

25

35


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

2

4

6

8

10


Flow Rate (L/min)


0

5

15

10

20

3025

35


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

15105

20

3025

35


Flow Rate (L/min)


051015

20253035


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

2

4

6

8

10


Flow Rate (L/min)

　　

　

BZL0100-A：Meter-in BZL0200-A：Meter-in BZL0300-A：Meter-in

BZL0100-B：Meter-out BZL0200-B：Meter-out BZL0300-B：Meter-out

Flow Rate Graph < Hydraulic Fluids ISO-VG32（25～35℃）>

Fully Closed

Fully OpenedFully OpenedFully Opened


Fully ClosedFully Closed


Fully Closed

Pressure Loss 5MPa Pressure Loss 5MPa Pressure Loss 5MPa

Pressure Loss 5MPaPressure Loss 5MPaPressure Loss 5MPa





895

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest

Model No.Indication Specifications External

DimensionsExternalDimensionsFlow Rate GraphFlow Rate GraphApplicable

ProductsControl Valve　Speed Control Valve (For Low Pressure) model BZL

External Dimensions


Model No.ABCDEFGHJKL

M (Nominal×Pitch)NPQ

R (Flat Surface Area)STUVW

BZL0100-□ BZL0200-□ BZL0300-□ 14 18 22 15.5 20 24 15 16 19 12 13 16 8.5 9.5 11 (11.6) (15.1) (17.6) G1/8 G1/4 G3/8 3 3 3 3.5 3.5 5 10 10 13 3 3 4 M6×0.75 M6×0.75 M8×0.75 11.5 15 17.5 8.5 11※1 13 9 11.5 13 16 20.5 24.5 10 13.5 17 8.7 11.5 15 G1/8 G1/4 G3/8 2 ～ 3 3 ～ 4 4 ～ 5 2.5 ～ 5 3.5 ～ 7 4.5 ～ 9

Notes : 1. Since the area is sealing part, be careful not to damage it. 2. Since the area is the metal sealing part of BZL, be careful not to damage it. (Especially when deburring) 3. No cutting chips or burr should be at the tolerance part of machining hole. 4. As shown in the drawing, P1 port is used as the hydraulic supply and P2 port as the clamp side. 5. If mounting plugs or fittings with G thread specification available in the market, the dimension '※1' should be 12.5.

Adjusting Screw

0.2

45°

0.4

BZL0□00

- □

(Clamp/Cylinder)

G ThreadExclusive Packing(Included)

P2 PortClamp Side

Fmax.H

max.CDEJ

φB

Hex. Socket L

M Screw

Hexagon KHexagon A

φT

max.φS

min.φR

φVQ

P1 PortHydraulic PressureSupply Side

φW

P2 PortClamp Side

U Thread(Prepared HoleφTFlat Bottom)

min.PNZ

Z⊥ 0.1

Attention 0- 0.10

OPENCLOSE

P1 PortHydraulic PressureSupply Side (mm)

Notes 1. Please read "Notes on Hydraulic Cylinder Speed Control Circuit" to assist with proper hydraulic circuit design.

If there is something wrong with the circuit design, it leads to the applications malfunction and damage. (Refer to P.1238)

2. It is dangerous to air bleed during operation under high pressure. It must be done under lower pressure.

(For reference: the minimum operating range of the product within the circuit.)


0

2

4

6

8

10


Flow Rate (L/min)


0

2

4

6

8

10


Flow Rate (L/min)


0

5

15

10

20

30

25

35


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

2

4

6

8

10


Flow Rate (L/min)


0

5

15

10

20

3025

35


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

15105

20

3025

35


Flow Rate (L/min)


051015

20253035


Flow Rate (L/min)


0

5

10

15

20

25


Flow Rate (L/min)


0

2

4

6

8

10


Flow Rate (L/min)

　　

　

BZL0100-A：Meter-in BZL0200-A：Meter-in BZL0300-A：Meter-in

BZL0100-B：Meter-out BZL0200-B：Meter-out BZL0300-B：Meter-out

Flow Rate Graph < Hydraulic Fluids ISO-VG32（25～35℃）>

Fully Closed





Fully Closed







896

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest P.891 Model No. IndicationModel No. Indication SpecificationsSpecifications External DimensionsExternal DimensionsApplicable ProductsApplicable ProductsControl Valve　Air Bleed Valve model BZX

Model No. Indication (Air Bleed Valve)

Specifications Circuit Symbol

1 2

BZX0 1 0

2

1 G Thread Size





Design No.

MPaMPa

℃N･m

BZX010

G1/8A

10

BZX0202537.5G1/4A


BZX030

G3/8A

35

Model No.Max. Operating PressureWithstanding PressureG Thread SizeUsable FluidOperating Temperature Tightening Torque for Main Body

Notes : 1. Do not over loosen the plug during air venting. (Do not loosen for more than 2 turns from the fully closed position.) 2. It is dangerous to have air venting operation under high pressure. It must be done under lower pressure. (For reference: the minimum operation pressure range of the product within the circuit) 3. Refer to the machining dimensions for BZL mounting area.

Thread Part

External Dimensions

Model No.ABCDEG

BZX010 BZX020 BZX030 14 18 22 15.5 20 24 19.8 20.6 20.6 9.3 10.1 10.1 5.5 6.3 6.3 G1/8 G1/4 G3/8

(mm)

Applicable Products

LKA (Double Action)Link ClampLKA0360-C□□-□LKA0400-C□□-□LKA0480-C□□-□LKA0550-C□□-□


LT (Single Action)Swing ClampLT0301-C□-□LT036□-C□-□LT040□-C□-□LT048□-C□-□LT055□-C□-□LT065□-C□-□LT075□-C□-□

LG (Single Action)Swing ClampLG0301-C□-□LG036□-C□-□LG040□-C□-□LG048□-C□-□LG055□-C□-□LG065□-C□-□LG075□-C□-□LG090□-C□-□LG105□-C□-□

Model No.

BZX010

BZX020

BZX030

LKC (Double Action)Link ClampLKC0400-C□-□LKC0480-C□-□LKC0550-C□-□

LKC0650-C□-□


LC (Single Action)Work SupportLC0262-C□LC0302-C□LC0362-C□LC0402-C□□-□LC0482-C□□-□LC0552-C□□-□LC0652-C□□-□LC0752-C□□-□LC0902-C□□-□

DBA (Double Action)Block CylinderDBA0250-C□DBA0320-C□


DBC (Double Action)Block CylinderDBC0250-C□DBC0320-C□


FVA (Double Action)Centering ViseFVA0400FVA0630FVA1000

FVC (Double Action)Centering ViseFVC0630

FVC1000FVC1600

FVD (Double Action)Centering ViseFVD1600FVD2500

FVD4000

Model No.

BZX010

BZX020

BZX030

LHA (Double Action)Swing ClampLHA0360-C□□-□LHA0400-C□□-□LHA0480-C□□-□LHA0550-C□□-□


LHC (Double Action)Swing ClampLHC0360-C□□-□LHC0400-C□□-□LHC0480-C□□-□LHC0550-C□□-□

LHC0650-C□□-□

LHE (Double Action)High-Power Swing ClampLHE0300-C□LHE0360-C□LHE0400-C□LHE0480-C□LHE0550-C□

LHW (Double Action)Swing ClampLHW040□-C□□-□LHW048□-C□□-□LHW055□-C□□-□

LHW065□-C□□-□LHW0751-C□□-□

LHS (Double Action)Swing ClampLHS0360-C□□-□LHS0400-C□□-□LHS0480-C□□-□LHS0550-C□□-□


Model No.

BZX010

BZX020

BZX030

LL (Double Action)Linear CylinderLL0360-C□□-□LL0400-C□□-□LL0480-C□□-□LL0550-C□□-□

LL0650-C□□-□LL0750-C□□-□LL0900-C□□-□LL1050-C□□-□

LLR (Double Action)Linear CylinderLLR0360-C□□-□-□LLR0400-C□□-□-□LLR0480-C□□-□-□LLR0550-C□□-□-□

LLR0650-C□□-□-□LLR0750-C□□-□-□LLR0900-C□□-□-□LLR1050-C□□-□-□

LLW (Double Action)Lift CylinderLLW036□-C□□-□LLW040□-C□□-□LLW048□-C□□-□


LKW040□-C□□-□LKW048□-C□□-□LKW055□-C□□-□

LKW065□-C□□-□LKW0751-C□□-□

LM (Single Action)Link ClampLM0300-C□LM0360-C□LM0400-C□LM0480-C□LM0550-C□LM0650-C□LM0750-C□

LJ (Single Action)Link ClampLJ0302-C□LJ0362-C□LJ0402-C□LJ0482-C□LJ0552-C□LJ0652-C□LJ0752-C□LJ0902-C□LJ1052-C□

G Thread

Exclusive Packing (Included)

Lock NutM6 (3 types)

Hexagon AHexagon 10Hex. Socket 3

10.5E

3.63.8D

C

φB

BodyPlugM6×1

(Clamp / Cylinder)

899

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest P.891 Model No. IndicationModel No. Indication SpecificationsSpecifications External DimensionsExternal DimensionsApplicable ProductsApplicable ProductsControl Valve　Air Bleed Valve model BZX

Model No. Indication (Air Bleed Valve)

Specifications Circuit Symbol

1 2

BZX0 1 0

2

1 G Thread Size





Design No.

MPaMPa

℃N･m

BZX010

G1/8A

10

BZX0202537.5G1/4A


BZX030

G3/8A

35

Model No.Max. Operating PressureWithstanding PressureG Thread SizeUsable FluidOperating Temperature Tightening Torque for Main Body

Notes : 1. Do not over loosen the plug during air venting. (Do not loosen for more than 2 turns from the fully closed position.) 2. It is dangerous to have air venting operation under high pressure. It must be done under lower pressure. (For reference: the minimum operation pressure range of the product within the circuit) 3. Refer to the machining dimensions for BZL mounting area.

Thread Part

External Dimensions

Model No.ABCDEG

BZX010 BZX020 BZX030 14 18 22 15.5 20 24 19.8 20.6 20.6 9.3 10.1 10.1 5.5 6.3 6.3 G1/8 G1/4 G3/8

(mm)

Applicable Products



LT (Single Action)Swing ClampLT0301-C□-□LT036□-C□-□LT040□-C□-□LT048□-C□-□LT055□-C□-□LT065□-C□-□LT075□-C□-□

LG (Single Action)Swing ClampLG0301-C□-□LG036□-C□-□LG040□-C□-□LG048□-C□-□LG055□-C□-□LG065□-C□-□LG075□-C□-□LG090□-C□-□LG105□-C□-□

Model No.

BZX010

BZX020

BZX030


LKC0650-C□-□









FVC1000FVC1600


FVD4000

Model No.

BZX010

BZX020

BZX030




LHC0650-C□□-□



LHW065□-C□□-□LHW0751-C□□-□



Model No.

BZX010

BZX020

BZX030


LL0650-C□□-□LL0750-C□□-□LL0900-C□□-□LL1050-C□□-□





LKW040□-C□□-□LKW048□-C□□-□LKW055□-C□□-□

LKW065□-C□□-□LKW0751-C□□-□



G Thread

Exclusive Packing (Included)

Lock NutM6 (3 types)

Hexagon AHexagon 10Hex. Socket 3

10.5E

3.63.8D

C

φB

BodyPlugM6×1

(Clamp / Cylinder)

900

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest P.891 Model No. IndicationModel No. Indication SpecificationsSpecifications External DimensionsExternal DimensionsApplicable ProductsApplicable ProductsControl Valve　G Thread Plug model JZG

Model No.ABCDG

JZG010 JZG020 JZG030 14 18 22 3.5 4.5 4.5 8 9 10 5 6 8 G1/8A G1/4A G3/8A

(mm)

CB

φA

Hex. Socket D

Exclusive Packing(Included)

G Thread

External Dimensions

Applicable Products

TLA-2 (Double Action)Swing ClampTLA0401-2C□-□TLA0601-2C□-□TLA0801-2C□-□TLA1001-2C□-□TLA1601-2C□-□TLA2001-2C□-□TLA2501-2C□-□TLA4001-2C□-□

Model No.

JZG010

JZG020

TLB-2 (Double Action)Swing ClampTLB0401-2C□-□TLB0601-2C□-□TLB0801-2C□-□TLB1001-2C□-□TLB1601-2C□-□TLB2001-2C□-□TLB2501-2C□-□TLB4001-2C□-□

TLA-1 (Single Action)Swing ClampTLA0402-1C□TLA0602-1C□TLA0802-1C□TLA1002-1C□TLA1602-1C□TLA2002-1C□TLA2502-1C□TLA4002-1C□

TMA-2 (Double Action)Link ClampTMA0250-2C□TMA0400-2C□TMA0600-2C□TMA1000-2C□

TMA1600-2C□TMA2500-2C□TMA3200-2C□


TMA1600-1C□TMA2500-1C□TMA3200-1C□



Model No.

JZG010

JZG020

JZG030


LKC0650-C□-□



LKW040□-C□□-□LKW048□-C□□-□LKW055□-C□□-□

LKW065□-C□□-□LKW0751-C□□-□





Model No.

JZG010

JZG020

JZG030




LHC0650-C□□-□



LHW065□-C□□-□LHW0751-C□□-□







Model No.

JZG010

JZG020



FVC1000FVC1600


FVD4000


LT065□-C□-□LT075□-C□-□


LG065□-C□-□LG075□-C□-□LG090□-C□-□LG105□-C□-□


LL0650-C□□-□LL0750-C□□-□LL0900-C□□-□LL1050-C□□-□



Model No. Indication (G Thread Plug with Air Bleeding Function)

1 2

JZG0 1 0

2

1 G Thread Size





Design No.

Thread Part

Specifications

MPaMPa

℃

N･m

JZG010

G1/8A

108

JZG0203542G1/4A


JZG030

G3/8A

3528

Model No.Max. Operating PressureWithstanding PressureG Thread SizeUsable FluidOperating Temperature Tightening Torquefor Main Body

Female Thread Side Material：SteelFemale Thread Side Material：Aluminum (For LT/LM※1)

Notes : 1. It is dangerous to have air venting operation under high pressure. It must be done under lower pressure. (For reference : the minimum operation pressure range of the product within the circuit) 2. Refer to the machining dimensions for BZL mounting area. ※1. Body material of LT/LM is aluminum alloy, so install it with the tightening torque for aluminum.

901

Work Support

LDLCTNCTC

Swing Clamp

LHA

Pneumatic Series

Hydraulic Series


Cautions / Others

High-PowerSeries


Hole Clamp

SFASFC

Link Clamp


Block Cylinder

DBADBC

Pallet Clamp

VSVT


VFLVFMVFJVFK

FPFQ

Pull Stud Clamp

FVAFVDFVC

Centering Vise

DWA/DWB



LLW


Compact Cylinder

LLLLRLLUDPDRDSDT

Control Valve

BZLBZTBZX/JZG

Control ValveDigest P.891 Model No. IndicationModel No. Indication SpecificationsSpecifications External DimensionsExternal DimensionsApplicable ProductsApplicable ProductsControl Valve　G Thread Plug model JZG

Model No.ABCDG

JZG010 JZG020 JZG030 14 18 22 3.5 4.5 4.5 8 9 10 5 6 8 G1/8A G1/4A G3/8A

(mm)

CB

φA

Hex. Socket D

Exclusive Packing(Included)

G Thread

External Dimensions

Applicable Products

TLA-2 (Double Action)Swing ClampTLA0401-2C□-□TLA0601-2C□-□TLA0801-2C□-□TLA1001-2C□-□TLA1601-2C□-□TLA2001-2C□-□TLA2501-2C□-□TLA4001-2C□-□

Model No.

JZG010

JZG020

TLB-2 (Double Action)Swing ClampTLB0401-2C□-□TLB0601-2C□-□TLB0801-2C□-□TLB1001-2C□-□TLB1601-2C□-□TLB2001-2C□-□TLB2501-2C□-□TLB4001-2C□-□

TLA-1 (Single Action)Swing ClampTLA0402-1C□TLA0602-1C□TLA0802-1C□TLA1002-1C□TLA1602-1C□TLA2002-1C□TLA2502-1C□TLA4002-1C□


TMA1600-2C□TMA2500-2C□TMA3200-2C□


TMA1600-1C□TMA2500-1C□TMA3200-1C□



Model No.

JZG010

JZG020

JZG030


LKC0650-C□-□



LKW040□-C□□-□LKW048□-C□□-□LKW055□-C□□-□

LKW065□-C□□-□LKW0751-C□□-□





Model No.

JZG010

JZG020

JZG030




LHC0650-C□□-□



LHW065□-C□□-□LHW0751-C□□-□







Model No.

JZG010

JZG020



FVC1000FVC1600


FVD4000


LT065□-C□-□LT075□-C□-□


LG065□-C□-□LG075□-C□-□LG090□-C□-□LG105□-C□-□


LL0650-C□□-□LL0750-C□□-□LL0900-C□□-□LL1050-C□□-□



Model No. Indication (G Thread Plug with Air Bleeding Function)

1 2

JZG0 1 0

2

1 G Thread Size





Design No.

Thread Part

Specifications

MPaMPa

℃

N･m

JZG010

G1/8A

108

JZG0203542G1/4A


JZG030

G3/8A

3528

Model No.Max. Operating PressureWithstanding PressureG Thread SizeUsable FluidOperating Temperature Tightening Torquefor Main Body

Female Thread Side Material：SteelFemale Thread Side Material：Aluminum (For LT/LM※1)

Notes : 1. It is dangerous to have air venting operation under high pressure. It must be done under lower pressure. (For reference : the minimum operation pressure range of the product within the circuit) 2. Refer to the machining dimensions for BZL mounting area. ※1. Body material of LT/LM is aluminum alloy, so install it with the tightening torque for aluminum.

902

Company Profile

Overseas Affiliates and Sales OfficesDistributors

CanadaU.S.A.CanadaU.S.A.

EuropeEurope

Asia

BrazilBrazil

Asia

Australia

MexicoMexico

JapanChina

Taiwan

PhilippinesThailand

Japan

Korea

China

Taiwan

PhilippinesThailand

IndiaIndia

Korea

SingaporeSingaporeMalaysiaMalaysia

IndonesiaIndonesia

Global Network

Asia Detailed Map

● FOR FURTHER INFORMATION ON UNLISTED SPECIFICATIONS AND SIZES, PLEASE CALL US.● SPECIFICATIONS IN THIS CATALOG ARE SUBJECT TO CHANGE WITHOUT NOTICE.

JQA-QMA10823KOSMEK HEAD OFFICE

Sales Offices

TEL.078-991-5115 FAX.078-991-8787

Sales Offices in Japan

〒651-2241 兵庫県神戸市西区室谷2丁目1番5号

Tokyo Sales OfficeTEL.048-652-8839 FAX.048-652-8828

〒331-0815 埼玉県さいたま市北区大成町4丁目81番地

Nagoya Sales OfficeTEL.0566-74-8778 FAX.0566-74-8808

〒446-0076 愛知県安城市美園町2丁目10番地1

Fukuoka Sales OfficeTEL.092-433-0424 FAX.092-433-0426

〒812-0006 福岡県福岡市博多区上牟田1丁目8-10-101

Head OfficeOsaka Sales OfficeOverseas Sales

Japan

Overseas Sales

TEL. +81-78-991-5162 FAX. +81-78-991-8787

Sales Offices across the World

〒651-2241 兵庫県神戸市西区室谷2丁目1番5号

USA

KOSMEK（USA）LTD.

G.E.T. Inc, Phil.

TEL. +1-630-620-7650 FAX. +1-630-620-9015650 Springer Drive, Lombard, IL 60148 USA

EUROPE

KOSMEK EUROPE GmbH

TEL. +43-463-287587 FAX. +43-463-287587-20Schleppeplatz 2 9020 Klagenfurt am Wörthersee Austria

Thailand TEL. +66-2-300-5132 FAX. +66-2-300-5133 67 Soi 58, RAMA 9 Rd., Suanluang, Suanluang, Bangkok 10250, Thailand

Victoria Wave Special Economic Zone Mt. Apo Building, Brgy. 186, North Caloocan City, Metro Manila, Philippines 1427

China

考世美(上海)貿易有限公司

TEL.+86-21-54253000 FAX.+86-21-54253709

中国上海市浦东新区浦三路21弄55号银亿滨江中心601室200125

Taiwan

盈生貿易有限公司

Thailand Representative Office

Mexico TEL. +52-442-161-2347Blvd Jurica la Campana 1040, B Colonia Punta Juriquilla Queretaro, QRO 76230 MexicoKOSMEK USA Mexico Office

TEL. +886-2-82261860 FAX. +886-2-82261890

台湾新北市中和區建八路2號 16F-4（遠東世紀廣場）

Philippines TEL.+63-2-310-7286 FAX. +63-2-310-7286

P.T PANDU HYDRO PNEUMATICS Ruko Green Garden Blok Z-Ⅱ No.51 Rt.005 Rw.008 Kedoya Utara-Kebon Jeruk Jakarta Barat 11520 Indonesia

Indonesia TEL. +62-21-5818632 FAX. +62-21-5814857

16F-4, No.2, Jian Ba Rd., Zhonghe District, New Taipei City Taiwan 23511

Room601, RIVERSIDE PYRAMID No.55, Lane21, Pusan Rd, Pudong Shanghai 200125, China

KOSMEK LTD. 1-5, 2-chome, Murotani, Nishi-ku, Kobe-city, Hyogo, Japan 651-2241

KOSMEK（CHINA）LTD.

Full Life Trading Co., Ltd.

(Indonesia Exclusive Distributor)

(Philippines Exclusive Distributor)

(Taiwan Exclusive Distributor)

India

KOSMEK LTD. - INDIA

TEL.+91-9880561695F 203, Level-2, First Floor, Prestige Center Point, Cunningham Road, Bangalore -560052 India

high accuracy model for locating workpiece … support ld lc tnc tc swing clamp lha pneumatic series...

Documents