horizontal recessed-mounted with stainless steel … · concealed pneumatic cylinder and hinge...

Rough Wall Opening35-1/2" (900mm) wide20-1/2" (529mm) high4" (102mm) minimum recessed depth

37.0 in.(940 mm)

23 in.(584 mm)

33 in.(838 mm)

from f loormax

15.25 in.(387 mm)

2 in.(51 mm)

48 in.(1,283 mm)

From Floor(ADA)

8.25 in.(210 mm)

20 in.508 mm

9.25 in.(235 mm)

4.0 in.102 mm

F i n i s h f a c e o f w a l l

2.5 in.64 mm

Floor

32.0 in.(813 mm)

8.25 in.(210 mm)

HORIZONTALRECESSED-MOUNTED

WITH STAINLESS STEEL FLANGEBABY CHANGING STATION

KB100-00ST-INB CREAMKB100-01ST-INB GREY

KB100-05ST-INB WHITE GRANITE

ADA Compliance (when properly installed) 4.4.1 Max. Protruding Objects 4.2.5 Forward Reach 4.2.6 Side Reach 4.27.4 Operation Continued...

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer KB100-ST-INB Revised 12-12-07 Printed In USAreserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2007 by Koala Kare Products, A Division of Bobrick

6982 S. Quentin St.Centennial, CO 80112, USA

Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer KB100-ST-INB Revised 12-12-07 Printed In USAreserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2007 by Koala Kare Products, A Division of Bobrick

MATERIALS:

FDA approved blow-molded high-density (Cream, Grey, or White Granite) polyethelene with Microban® antimicrobialembedded in plastic and 18-gauge, type 304 brushed stainless steel finish flange. Reinforced full-length steel-on-steelhinge mechanism, with 11-gauge steel mounting plates and mounting hardware included. Molded in graphics and safetymessages in six languages. Contoured changing surface area is 442 sq. in. (2873 sq. mm) and comes complete withnylon safety straps and bag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-densitypolyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performancerequirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.

Warning: To insure that the unit supports the intended loads, baby changing stations must be properly installedaccording to the manufacturer’s instructions.

INSTALLATION:

To insure proper installation and compliance to building codes, it is recommendedthat a qualified person or carpenter perform the installation of the unit. The unitmust be properly installed onto a permanent wall that is capable of supportingsignificant weight and can accommodate the supplied installation hardware. TheKoala Baby Changing Station meets ADA regulations when properly installed.

Drilling holes and mounting the station:

1. Remove the station from the shipping container and check for any freightdamage. Identify the best location for installing the Baby Changing Station.Hold the unit in place, open the bed, and make sure that there is adequateoperating clearance.

2. Select the wall area where the Baby Changing Station will be installed.Measure from the floor, at the center of the stud, and mark the wall for theappropriate height. Hold the unit in place to verify alignment. Cut an openingin the wall 35-1/2" (900mm) wide, 20-1/2" (529mm) high, 4" (102mm)minimum depth and install framing on top, bottom and sides of wall opening.If the wall surface is masonry or tile over wood studs, use caution whencutting the hole for the unit.

3. The unit will be mounted using 4-1/4" (108mm) x 1-1/2" (38mm) woodscrews through the sides of the unit into the framing of the wall opening.

4. Place the unit into the recessed wall opening and insert the screws and flatwashers to hold the Baby Changing Station in place. It may be necessary toadjust the squareness of the door by using a shim on the top right or left sideof the unit before tightening securely to the wall.

SPECIFICATION:

Baby changing station body durable high-density (Cream, Grey or White Granite) polyethelene with Microban® anti-microbial with an 18-gauge, type 304 brushed stainless steel finish flange. Design of unit shall be recessed-mounted.Unit shall be equipped with a pneumatic cylinder for controlled opening and closing of bed. Bed shall be secured to backplate with a concealed, full-length steel-on-steel hinge. No hinge structure shall be exposed on interior surfaces. Unitshall have 11-gauge steel mounting plates with mounting hardware included. Unit shall have Microban® antimicrobialembedded into plastic material Unit shall conform to ANSI S117.1 Accessible and Usable Buildings and Facilities,ASTM F 2285-04 Standard Consumer Safety Performance Specification for Diaper Changing Tables for CommercialUse, ANSI Z535.4 Product Safety Signs and Labels, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards orlocal code if more stringent installation requirements are applicable for barrier-free accessibility. Unit shall comply withADA regulations when properly installed. Bed shall have smooth concave changing area with a nylon safety strap andtwo hooks for bags or purses. Unit shall have a built-in Liner Dispenser for use with 3-ply chemical free biodegradablesanitary liners, universal instruction graphics and safety messages in 6 languages. Unit shall be backed bymanufacturer’s 5-year limited warranty on materials and workmanship, and a 5-year replacement warranty againstvandalism. Unit shall be manufactured in the U.S.A.

Baby Changing Station shall be model KB100-ST-INB of Koala Kare Products, A Division of Bobrick6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

HORIZONTALWALL-MOUNTED

BABY CHANGING STATION

KB100-00-INB CREAMKB100-01-INB GREY

KB100-05-INB WHITE GRANITE


The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer KB100-INB Revised 12-12-07 Printed In USAreserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2007 by Koala Kare Products, A Division of Bobrick

32 in.(813 mm)

35.25 in.(895 mm)

8.25 in.(210 mm)

20 in.(508mm)

33 in.(838 mm)

f rom fl oor

19.25 in.(489 mm)

48 in.(1218 mm)

From f loor(ADA)

4.0 in.(102 mm)

F in i sh f a ce o f wa l l

Floor

2.5 in.(64 mm)

9.25 in.(235 mm)

1.625 in.(41 mm)


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

Continued...


MATERIALS:

FDA approved blow-molded high-density polyethylene with Microban® Antimicrobial additive. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mounting hardware included. Molded in graphicsand safety messages in six languages and braille. Contoured changing surface area is 442 sq. in. (2873 sq. mm) andcomes complete with nylon safety straps and bag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-densityPolyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performancerequirements when properly installed. Molded-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.


INSTALLATION:

To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenterperform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supportingsignificant weight and can accommodate the supplied installation hardware. The Koala Baby Changing Station meetsADA regulations when properly installed.


1. Remove the station from the shipping container and check for any freight damage. Identify the best location forinstalling the baby changing station. Hold the unit in place, open the bed, and make sure that there is adequateoperating clearance.

2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not all ofincluded hardware may be required for proper installation.

3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32"(813mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in thedesired location. If the walls do not have studs on the center as outlined, make sure at least one side of the unit isinstalled into the stud. Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 45.5"(1,156 mm) up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole withthis mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate thebottom of the station 28" (711 mm) from the floor and the top of the bed at 33" (838 mm).

Using Wood Screws:

If the wall has wood studs on 16" (406mm) or 32" (813mm) centers, drill 1/8" (3mm) pilot holes at the marks and use thefour 1/4" (6mm) x 3" (76mm) panhead tapping screws with supplied washers. If the wall is masonry or tile over woodstuds, use a 7/32" (6mm) masonry drill until you hit the stud, then proceed to drill 1/8" (3mm) pilot holes into the studsand use the four 1/4" (6mm) x 3" (76mm) panhead tapping screws with supplied washers.

Using Toggle Fasteners:

If the wall has wood studs that are not on 16" (406mm) or 32" (813mm) centers, has metal studs, or an underlyingsurface of concrete block, drill with a 1/2" (13mm) masonry bit. A minimum of 2-1/2" (64mm) of inside wall space isrequired for toggles to turn. Insert supplied toggles and tighten, locate station over toggles, then use supplied 1/4" (6mm)x 3" (76mm) Phillips Panhead machine screws with supplied washers.

SPECIFICATION:

Baby changing station body shall be durable, high-density polyethylene. Design of unit shall be surface-mounted. Unitshall be equipped with a pneumatic cylinder for controlled opening and closing of bed. Bed shall be secured to back platewith a concealed, full-length steel-on-steel hinge. No hinge structure shall be exposed on interior or exterior surfaces.Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shall have Microban® Antimicrobialembedded into plastic material. Unit shall conform to ANSI S117.1 Accessible and Usable Building and Facilities, ASTMF 2285-04 Standard Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4Product Safety Signs and Labels, ASTM G21 Antifungal, ASTM G22 Antibacterial standards or local code if morestringent installation requirements are applicable for Barrier-Free accessibility. Unit shall comply with ADA regulationswhen properly installed. Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bagsor purses.


Unit shall have a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universalinstruction graphics and safety messages in 6 languages and braille. Unit shall be backed by manufacturer’s 5-yearlimited warranty on materials and workmanship, and 5-year replacement warranty against vandalism. Unit shall bemanufactured in the U.S.A.

Baby Changing Station shall be model KB100-INB of Koala Kare Products, A Division of Bobrick6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com




KB100-05-INB WHITE GRANITE



32 in.(813 mm)

35.25 in.(895 mm)

8.25 in.(210 mm)

20 in.(508mm)

33 in.(838 mm)

f rom fl oor

19.25 in.(489 mm)

48 in.(1218 mm)

From f loor(ADA)

4.0 in.(102 mm)

F in i sh f a ce o f wa l l

Floor

2.5 in.(64 mm)

9.25 in.(235 mm)

1.625 in.(41 mm)


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

Continued...


MATERIALS:

FDA approved blow-molded high-density polyethylene with Microban® Antimicrobial additive. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mounting hardware included. Molded in graphicsand safety messages in six languages and braille. Contoured changing surface area is 442 sq. in. (2873 sq. mm) andcomes complete with nylon safety straps and bag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-densityPolyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performancerequirements when properly installed. Molded-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.


INSTALLATION:





3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32"(813mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in thedesired location. If the walls do not have studs on the center as outlined, make sure at least one side of the unit isinstalled into the stud. Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 45.5"(1,156 mm) up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole withthis mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate thebottom of the station 28" (711 mm) from the floor and the top of the bed at 33" (838 mm).

Using Wood Screws:




SPECIFICATION:

Baby changing station body shall be durable, high-density polyethylene. Design of unit shall be surface-mounted. Unitshall be equipped with a pneumatic cylinder for controlled opening and closing of bed. Bed shall be secured to back platewith a concealed, full-length steel-on-steel hinge. No hinge structure shall be exposed on interior or exterior surfaces.Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shall have Microban® Antimicrobialembedded into plastic material. Unit shall conform to ANSI S117.1 Accessible and Usable Building and Facilities, ASTMF 2285-04 Standard Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4Product Safety Signs and Labels, ASTM G21 Antifungal, ASTM G22 Antibacterial standards or local code if morestringent installation requirements are applicable for Barrier-Free accessibility. Unit shall comply with ADA regulationswhen properly installed. Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bagsor purses.


Unit shall have a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universalinstruction graphics and safety messages in 6 languages and braille. Unit shall be backed by manufacturer’s 5-yearlimited warranty on materials and workmanship, and 5-year replacement warranty against vandalism. Unit shall bemanufactured in the U.S.A.

Baby Changing Station shall be model KB100-INB of Koala Kare Products, A Division of Bobrick6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

Fin ish face of wal l

20.5 in.(521 mm)

16 in.(406 mm)

33.875 in.(860 mm)

11.4375 in.(291 mm)

4 in..(102 mm)

20.5 in.(521 mm)

Floor

49.5 in.(1257 mm)

from f loor

33 in.(838 mm)

3.5 in.(89 mm)


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

OVALWALL-MOUNTED



KB108-12-INB GREY GRANITE



Continued...


MATERIALS:

FDA approved rotation-molded high-density polyethylene with Microban® antimicrobial. Reinforced full-length steel-on-steel hinge mechanism and mounting hardware included. Molded in graphics and safety messages in five languages.Contoured changing surface area is 307.72 sq. in. (198,529 sq. mm) and comes complete with nylon safety straps andbag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-densitypolyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performancerequirements when properly installed.


INSTALLATION:

To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenterperform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supportingsignificant weight, and can accomodate the supplied installation hardware. The Koala Baby Changing Station meets ADAregulations when properly installed.


1. Remove the station from the shipping container and check for any freight damage. Identify the best location forinstalling the Baby Changing Station. Hold the unit in place, open the bed, and make sure that there is adequateoperating clearance.


3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 16"(406mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in thedesired location. If the walls do not have studs on the center as outlined, make sure at least one side of the unitis installed into the stud. Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 46" (1168mm)up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole with this mark,then use a measuring tape and level to mark the remaining three mounting holes. This will locate the bottom ofthe station 29" (737mm) from the floor.

Using Wood Screws:

If the wall has wood studs on 16" (406mm) centers, drill 1/8" (3mm) pilot holes at the marks and use the four 1/4" (6mm)x 3" (76mm) panhead tapping screws with supplied washers. If the wall is masonry or tile over wood studs, use a7/32" (6mm) masonry drill until you hit the stud, then proceed to drill 1/8" (3mm) pilot holes into the studs and use thefour 1/4" (6mm) x 3" (76mm) panhead tapping screws with supplied washers.


If the wall has wood studs that are not on 16" (406mm) centers, has metal studs, or an underlying surface of concreteblock, drill with a 1/2" (13mm) masonry bit. A minimum of 2-1/2" (64mm) of inside wall space is required for toggles toturn. Insert supplied toggles and tighten, locate station over toggles, then use supplied 1/4" (6mm) x 3" (76mm) PhillipsPanhead machine screws with supplied washers.

SPECIFICATION:

Baby changing station body shall be durable, high-density polyethylene with Microban® antimicrobial. Design of unit shallbe surface-mounted, oval. Unit shall be equipped with a pneumatic cylinder for controlled opening and closing of bed.Bed shall be secured to back with a concealed, full-length steel-on-steel hinge. Unit shall have Microban® antimicrobialembedded into plastic material. No hinge structure shall be exposed on interior or exterior surfaces. Unit shall conform toANSI S117.1 Accessible and Useable Buildings and Facilities, ASTM F 2285-04 Standard Consumer Safety PerformanceSpecification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs and Labels, ASTMG21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringent installation requirements areapplicable for Barrier-free accessibility. Unit shall comply with ADA regulations when properly installed. Bed shall havesmooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shall have a built-inLiner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal instruction graphics and safety


messages in 5 languages. Unit shall be backed by manufacturers 5-year limited warranty on materials and workmanshipand a 5-year replacement warranty against vandalism. Unit shall be manufactured in the U.S.A.

Baby Changing Station shall be model KB108-INB of Koala Kare Products, A Division of Bobrick 6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

37.0 in.(940 mm)

23 in.(584 mm)

33 in.(838 mm)

from f loormax

15.25 in.(387 mm)

2 in.(51 mm)

48 in.(1,283 mm)

From Floor(ADA)

8.25 in.(210 mm)

20 in.(508 mm)

9.25 in.(235 mm)

4.0 in.102 mm


2.5 in.(64 mm)(64 mm)

Floor

32.0 in.(812 mm)

8.25 in.(210 mm)

Rough Wall Opening35-1/2" (900mm) wide20-1/2" (529mm) high4" (102mm) minimum recessed depth


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

HORIZONTALRECESSED-MOUNTED

STAINLESS STEELBABY CHANGING STATION

KB110-01-SSRE-INB GREY


The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer KB110-SSRE-INB Revised 12-12-07 Printed In USAreserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2007 by Koala Kare Products, A Division of Bobrick


MATERIALS:

18-gauge, type 304 satin stainless steel exterior finish with FDA approved blow molded high-density grey polyethylenewith Microban® antimicrobial interior. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steelmounting plates and mounting hardware included. Molded in graphics and safety messages in six languages. Contouredchanging surface area is 442 sq. in. (2873 sq. mm) and comes complete with nylon safety straps and bag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-densitypolyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performancerequirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.


INSTALLATION:



1. Remove the station from the shipping container and check for any freightdamage. Identify the best location for installing the Baby Changing Station.Hold the unit in place, open the bed, and make sure that there is adequateoperating clearance.

2. Select the wall area where the Baby Changing Station will be installed.Measure from the floor, at the center of the stud, and mark the wall for theappropriate height. Hold the unit in place to verify alignment. Cut an openingin the wall 35-1/2" (900mm) wide, 20-1/2" (529mm) high, 4" (102mm)minimum depth and install framing on top, bottom and sides of wall opening.If the wall surface is masonry or tile over wood studs, use caution whencutting the hole for the unit.

3. The unit will be mounted using 4-1/4" (108mm) x 1-1/2" (38mm) woodscrews through the sides of the unit into the framing of the wall opening.

4. Place the unit into the recessed wall opening and insert the screws and flatwashers to hold the Baby Changing Station in place. It may be necessary toadjust the squareness of the door by using a shim on the top right or left side of the unit before tightening securely to the wall.

SPECIFICATION:

Baby changing station body shall have 18-gauge, type 304 satin stainless steel exterior finish with high-density greypolyethylene interior. Design of unit shall be recessed-mounted. Unit shall be equipped with a pneumatic cylinder forcontrolled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-on-steelhinge. Unit shall have Microban® antimicrobial embedded into plastic material. No hinge structure shall be exposed oninterior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardware included. Unit shallconform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM F 2285-04 Standard Consumer Safetyperformance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signs andLabels, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringent installationrequirements are applicable for barrier-free accessibility. Unit shall comply with ADA regulations when properly installed.Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shallhave a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal instructiongraphics and safety messages in 6 languages. Unit shall be backed by manufacturer’s 5-year limited warranty onmaterials and workmanship, and a 5-year replacement warranty against vandalism. Unit shall be manufactured inthe U.S.A.

Baby Changing Station shall be model KB110-SSRE-INB of Koala Kare Products, A Division of Bobrick 6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

35.25 in.(892 mm)

32 in.(812 mm)

8.25 in.(210 mm)

20.0 in.(508 mm)

33 in.(838 mm)

f ro m f l o o r

15.1875 in.(386 mm) 4.0 in.

(102 mm)

48 in.(1 ,283 mm)f rom f loor


8.25 in.(206 mm)

20.0 in.(508 mm)

Floor

2.5 in.(64 mm)

9.25 in.(235 mm)


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com



KB110-01-SSWM-INB GREY


The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer KB110-SSWM-INB Revised 12-12-07 Printed In USAreserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2007 by Koala Kare Products, A Division of Bobrick

Continued...


MATERIALS:

18-gauge, type 304 satin stainless steel exterior finish with FDA approved blow molded high-density grey polyethylenewith Microban® antimicrobial interior. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steelmounting plates and mounting hardware included. Molded in graphics and safety messages in six languages. Contouredchanging surface area is 442 sq. in. (2873 sq. mm) and comes complete with nylon safety straps and bag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-densityPolyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performancerequirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.


INSTALLATION:





3. The horizontal unit has four mounting holes provided in the back wall of the unit, which are positioned on a 32"(813mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in thedesired location. If the walls do not have studs on the center as outlined, make sure at least one side of the unitis installed into the stud. Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 45.5"(1,156 mm) up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole withthis mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate thebottom of the station 28" (711 mm) and the top of the bed at 33" (838 mm) from the floor.

Using Wood Screws:




SPECIFICATION:

Baby changing station shall have 18-gauge satin stainless steel exterior finish with high-density polyethylene withMicroban® antimicrobial interior. Design of unit shall be surface-mounted. Unit shall be equipped with a pneumaticcylinder for controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-on-steel hinge. Unit shall have Microban® antimicrobial embedded into plastic material. No hinge structure shall beexposed on interior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardwareincluded. Unit shall conform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM F 2285-04 StandardConsumer Safety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 ProductSafety Signs and Labels, ASTM G21 Antifungal and ASTM G22 Antibacterial Standards or local code if more stringentinstallation requirements are applicable for barrier free accessibility. Unit shall comply with ADA regulations whenproperly installed. Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or


purses. Unit shall have a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universalinstruction graphics and safety messages in 6 languages. Manufacturer’s service and parts manual shall be provided tothe building owner/manager upon completion of project. Unit shall be backed by manufacturers’ 5-year limited warrantyon materials and workmanship, and a 5-year replacement warranty against vandalism. Unit shall be manufacturedin the U.S.A.

Baby Changing Station shall be model KB110-SSWM-INB of Koala Kare Products, A Division of Bobrick 6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

24.25 in.(616 mm)

22.75 in.(578 mm)

16 in.(406mm)

39.5 in.(1003 mm)

34 in.(864 mm)

from floor

29.75 in.(756 mm)

1.5 in.(38 mm)

2.75. in.(70 mm)

63.25 in.(1,607 mm)from floor

MountingPlates

35.5 in(902 mm)

Fin ish face of wal l

Floor

3.75 in.(95 mm)

1.25 in.(32 mm)

4.5 in.(114 mm)

12.25 in.(311 mm)

Rough Wall Opening22-1/2" (572mm) wide36" (914mm) high4" (102mm) minimum recessed depth


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

VERTICALRECESSED-MOUNTED


KB111-01-SSRE-INB GREY




MATERIALS:

FDA approved blow molded high-density polyethylene with Microban® antimicrobial clad in a type 304 brushed stainlesssteel finish. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mountinghardware included. Molded in graphics & Safety Messages in six languages. Contoured changing surface area is 420 sq.in. (2730 sq. mm) and comes complete with nylon safety straps and bag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. Stainless steelis easy to clean and resists odors and bacterial growth. Complies with ASTM static load performance requirements whenproperly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.


INSTALLATION:



1. Remove the station from the shipping container and checkfor any freight damage. Identify the best location forinstalling the baby changing station. Hold the unit in place,open the bed, and make sure that there is adequateoperating clearance.

2. Select the wall area where the Baby Changing Station willbe installed. Measure from the floor, at the center of thestud, and mark the wall at 62" (1575 mm). Hold the unit inplace to verify alignment. Cut a hole 22.5" (565mm) wide,36" (902mm) high and 4" (102mm) deep in the wall andconstruct mounting frame as shown in Fig1.0. If the wallsurface is masonry or tile over wood studs, use cautionwhen cutting the hole for the unit.

3. The unit comes with two mounting brackets that need to besecured to the mounting frame as shown in Fig 1.0.

4. Place the unit into the recessed area and insert the cappednuts and washers to hold the Baby Changing Station inplace. It may be necessary to adjust the squareness of thedoor by using a shim on the top right or left side of the unitbefore tightening securely to the wall.

SPECIFICATION:

Baby changing station body shall be durable, high-density polyethylene with Microban® antimicrobial clad in a 304brushed stainless steel finish. Design of unit shall be semi-recessed-mounted. Unit shall be equipped with a pneumaticcylinder for controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-on-steel hinge. Unit shall have Microban® antimicrobial embedded into plastic material. No hinge structure shall beexposed on interior or exterior surfaces. Unit shall have 11-gauge steel mounting plates with mounting hardwareincluded. Unit shall conform to ANSI S117.1 Accessible and Useable Building and Facilities, ASTM F 2285-04 StandardSafety Performance Specification for Diaper Changing Tables for Commercial Use, ANSI Z535.4 Product Safety Signsand Labels, ASTM G21 Antifungal, ASTM G22 Antibacterial standards or local code if more stringent installationrequirements are applicable for Barrier-Free accessibility. Unit shall comply with ADA regulations when properly installed.Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shallhave a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal instructiongraphics and safety messages in 6 languages. Unit shall be backed by manufacturers 5-year limited warranty onmaterials and workmanship, and a 5-year replacement warranty against vandalism. Unit shall be manufactured in theU.S.A.

Baby Changing Station shall be model KB111-SSRE-INB of Koala Kare Products, A Division of Bobrick 6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

Fig 1.0

62 in. (1575 mm)from floor

(ADA)

35. in.(889 mm)34 in.

(864 mm)fromfloor

5.25 in.(133 mm)


9.25 in.(235 mm)

35.50 in.(902 mm)

22.75 in.(578 mm)

3.5 in.(89 mm)

22 in.(565 mm)

16 in.(406 mm)

Floor

22.75 in.(578 mm)

3 in.(76 mm)

58.5 in. (1486 mm)from floor

(ADA)


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

VERTICALWALL-MOUNTED


KB111-01-SSWM-INB GREY



Continued...


MATERIALS:

FDA approved blow molded high-density polyethylene with Microban® antimicrobial clad in type 304 brushed stainlesssteel finish. Reinforced full-length steel-on-steel hinge mechanism, with 11-gauge steel mounting plates and mountinghardware included. Molded in graphics & Safety Messages in six languages. Contoured changing surface area is 420 sq.in. (2730 sq. mm) and comes complete with nylon safety straps and bag hooks.

OPERATION:

Concealed pneumatic cylinder and hinge structure provides controlled, slow opening and closing of bed. High-densityPolyethylene is easy to clean and resists odors and bacterial growth. Complies with ASTM static load performancerequirements when properly installed. Built-in liner dispenser holds approximately 25 KB150-99-INB sanitary liners.


INSTALLATION:

To insure proper installation and compliance to building codes, it is recommended that a qualified person or carpenterperform the installation of the unit. The unit must be properly installed onto a permanent wall that is capable of supportingsignificant weight, and can accommodate the supplied installation hardware. The Koala Baby Changing Station meetsADA regulations when properly installed.



2. Based upon the type of wall on which the unit will be mounted, determine the best method of mounting. Not allof the included hardware may be required for proper installation.

3. The vertical unit has four mounting holes provided in the back wall of the unit, which are positioned on a 16"(406mm) stud center. If possible, locate the wood or metal wall studs for fastening the changing station in thedesired location. If the walls do not have studs on center as outlined, make sure at least one side of the unit isinstalled into the stud. Use toggles (supplied) for holes on the other side.

4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure 58.5"(1,486 mm) up from the floor, at the center of the stud, and mark the wall. Line up the top left mounting hole withthis mark, then use a measuring tape and level to mark the remaining three mounting holes. This will locate thebottom of the station 27" (686 mm) from the floor and the top of the bed at 34" (864 mm) from the floor.

Using Wood Screws:

If the wall has wood studs on 16" (406mm) centers, drill 1/8" (3mm) pilot holes at the marks and use the four 1/4"(6mm)x 3" (76mm) panhead tapping screws with supplied washers. If the wall is masonry or tile over wood studs, use a 7/32"(6mm) masonry drill until you hit the stud, then proceed to drill 1/8" (3mm) pilot holes into the studs and use the four1/4" (6mm) x 3" (76mm) screws with supplied washers.


If the wall has wood studs that are not on 16" (406mm) centers, has metal studs, or an underlying surface of concreteblock, drill with a 1/2" (13mm) masonry bit. A minimum of 2-1/2" (64mm) of inside wall space is required for toggles toturn. Insert supplied toggles and tighten, locate station over toggles, then use supplied 1/4" (6mm) x 3" (76mm) Phillipspanhead machine screws with supplied washers.

SPECIFICATION:

Baby changing station body shall be durable, high-density polyethylene with Microban® antimicrobial clad in type 304brushed stainless steel finish. Design of unit shall be surface-mounted. Unit shall be equipped with a pneumatic cylinderfor controlled opening and closing of bed. Bed shall be secured to back plate with a concealed, full-length steel-on-steelhinge. No hinge structure shall be exposed on interior or exterior surfaces. Unit shall have 11-gauge steel mountingplates with mounting hardware included. Unit shall have Microban® antimicrobial embedded into plastic material. Unitshall conform to ANSI S117.1 Accessible and Usable Buildings and Facilities, ASTM F 2285-04 Standard SafetyPerformance Specification for Diaper Changing Table for Commercial Use, ANSI Z535.4 Product Safety Signsand Labels, ASTM G21 Antifungal, ASTM G22 Antibacterial standards or local code if more stringent installation


requirements are applicable for barrier free accessability. Unit shall comply with ADA regulations when properly installed.Bed shall have smooth concave changing area with a nylon safety strap and two hooks for bags or purses. Unit shallhave a built-in Liner Dispenser for use with 3-ply chemical free biodegradable sanitary liners, universal instructiongraphics and safety messages in 6 languages. Unit shall be backed by manufacturers 5-year limited warranty onmaterials and workmanship and a 5-year replacement warranty against vandalism. Unit shall be manufacturedin the U.S.A.

Baby Changing Station shall be model KB111-SSWM of Koala Kare Products, A Division of Bobrick 6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

36.5 in.(927 mm)

22.625 in.(575 mm)

1/4 in . mount ing holes x 6

3.25 in .(83 mm)

10.25 in.(260 mm)

14.8125 in.(376 mm)

Unit he ight from counter top


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

COUNTERTOPSURFACE-MOUNTED

BABY CHANGING STATIONKB112-01CT-INB GREY


The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer KB112-CT-INB Revised 12-12-07 Printed In USAreserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2007 by Koala Kare Products, A Division of Bobrick

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet.The manufacturer KB112-CT-INB Revised 12-12-07 Printed In USAreserves the right to, and does from time to time, make changes and improvements in designs and dimensions without notice. © 2007 by Koala Kare Products, A Division of Bobrick

MATERIALS:

FDA approved thermoformed high-density polyethylene. Mounting instructions and hardware included. Contouredchanging surface area is 379.04 sq. in. (244,541.45 sq. mm) comes complete with nylon safety straps.

OPERATION:

For use in restrooms where counter space is more abundant than wall space. High-density polyethylene has no sharpcorners, is easy to clean and resists odors and bacterial growth.


INSTALLATION:

To insure proper installation and compliance with building codes, it is recommended that a qualified person or carpenterperform the installation of the unit.


1. Remove the station from the shipping container and check for any freight damage. Identify the best location forinstalling the baby changing station.

2. Place the countertop BCS onto the counter surface and place in desired position. Using the countertop BCSmounting holes as a guide, mark the screw hole locations with a pencil. Remove countertop BCS and drill holeswith a #21 or 5/32" drill bit. Drill down 1-1/2" (32mm) deep.

3. Apply a suitable water sealant, such as silicone, around the bottom edge of the changing station, then set unitonto the countertop using the mounting holes as a guide. Fasten unit to countertop with supplied screws.

Caution:

Drill carefully through ceramic tile and other hard countertop materials.

SPECIFICATION:

Baby changing station shall be durable, high impact polyethylene body. Design of unit shall be countertop surfacemounted. Bed shall have smooth concave changing area with a nylon safety strap and universal instruction graphics.The unit shall be backed by a 5-year manufacturers limited warranty. Unit shall be manufactured in the U.S.A.

Baby Changing Station shall be model KB112-01CT-INB of Koala Kare Products, A Division of Bobrick 6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

Mount 2 in. (51 mm) from bottom of door or 14 in (356 mm) from f loor

12.5 in.(317 mm)

18.75 in.(476 mm)

17 in.(431 mm)

12.25 in.(311 mm)

8 in.(203 mm)

2 in.(51 mm)

F i n i s h f a c e o f w a l lF i n i s h f a c e o f w a l l

5.625 in.(143 mm)

2 in. (51 mm)Partition Panel


Main: +1 303-539-8300Fax: +1 303-539-8399

www.koalabear.com

CHILD PROTECTION SEAT KB102-00-INB CREAM




MATERIALS:

FDA approved blow-molded high-density polyethylene with Microban®. Stainless steel hinge rod. Textured seat surfacewith nylon safety straps that extend over child’s shoulders and between legs for security.

OPERATION:

Designed to mount on the wall of a restroom stall or a dressing room. Closed unit folds to less than 6" (143mm), andrequires less than 2 sq. ft. (600 sq. cm) of wall space. High-density polyethylene is easy to clean and resists fungal andbacterial growth. Can withstand static loads of 150 lbs (68 kilos).

Warning: To insure that the unit supports the intended loads, seat must be properly installed according to themanufacturer’s instructions.

INSTALLATION:

To insure proper installation and compliance with building codes, it is recommended that a qualified person or carpenterperform the installation of the unit. The Child Protection Seat must be properly installed onto wall or partition of restroomor fitting room that is capable of supporting significant weight and can accommodate the supplied installation hardware(or other suitable hardware, not included, if unit is to be installed on another type of wall such as a cinderblock orpermanent wall).


1. Remove the unit from the shipping container and check for any freight damage. Identify the best location forinstalling the Child Protection Seat. Hold the unit in place, open the seat, and make sure that there is adequateoperating clearance. Use the seat as a template for locating the four mounting holes onto the mounting surface.Seat bottom should be 2" (51mm) from bottom of wall/partition or 14" (356mm) from the floor, whichever is higher.

2. The Child Protection Seat has four mounting holes provided in the back wall of the unit, which are positioned8" (203mm) apart horizontally and 17" (432mm) apart vertically. Hardware included with unit is intended forinstallation of seat to a restroom or fitting room partition. If Installing onto another wall type separate hardware willbe required (not included).

3. Drill through partition using 3/8" (10mm) drill bit. 4. Insert the four threaded plugs with head holes (supplied) from the outside of the partition. 5. Mount the Child Protection Seat with the four 1/4" (6mm) screws and washers (supplied). 6. Place the label/decal on the outside of stall or fitting room door.

SPECIFICATION:

Child Protection Seat body shall be durable, high-density polyethylene. Design of unit shall be surface-mounted. Seatshall be secured to back plate with a concealed, full-length stainless steel hinge rod embedded in the plastic. Seat shallhave nylon safety straps. Unit shall support static loads of up to 150 lbs (68kg) when properly installed. Unit shall bebacked by a 5-year manufacturer’s limited warranty on materials and workmanship and a 5-year replacement warrantyagainst vandalism. Unit shall be manufactured in the U.S.A.

Baby Changing Station shall be model KB102-00-INB of Koala Kare Products, A Division of Bobrick6982 S. Quentin St. Centennial, CO 80112 USATel: 1-888-733-3456 within the USA or +1 303-539-8300 outside the USAWeb: www.koalabear.com or www.bobrick.com

horizontal recessed-mounted with stainless steel … · concealed pneumatic cylinder and hinge...

Documents