howstereolithography3-100112180735-phpapp01
TRANSCRIPT
-
7/29/2019 howstereolithography3-100112180735-phpapp01
1/6
How Stereolithography 3-D Layering WorksbyMarshall Brain
Print Cite Feedback
Share Recommend
Inside this Article
1. Introduction to How Stereolithography (3-D Layering) Works2. The Stereolithography Machine3. The Stereolithography Process4. What You Can Create with Stereolithography5. Costs of Stereolithography6. Lots More Information7. See more
Computer Videos
More Computer Videos
Stereolithography, also known as 3-D layering or 3-D printing, allows you to create solid, plastic,three-dimensional (3-D) objects from CAD drawings in a matter of hours. Whether you are a mechanicalengineer wanting to verify the fit of a part or an inventor looking to create a plastic prototype of aninvention, stereolithography gives you a fast, easy way to turn CAD drawings into real objects.
3-D printing is a very good example of the age we live in. In the past, it could conceivably take months to
prototype a part -- today you can do it hours. If you can dream up a product, you can hold a working
model in your hands two days later! In this edition ofHow Stuff Works, we will take a tour of
thestereolithography service bureau at PT CAM (Piedmont Triad Center for Advanced Manufacturing)
so that you can understand everything involved and see some actual 3-D models that this technology has
produced!
The Stereolithography Machine
PT CAM uses a stereolithography machine produced by3-D Systemsand shown here:
Stereolithography Image Gallery
http://computer.howstuffworks.com/about-author.htm#brainhttp://computer.howstuffworks.com/about-author.htm#brainhttp://computer.howstuffworks.com/about-author.htm#brainhttp://computer.howstuffworks.com/stereolith.htm/printablehttp://computer.howstuffworks.com/stereolith.htm/printablehttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/rate.htm?id=%2Fstereolith.htm&random=6125http://computer.howstuffworks.com/rate.htm?id=%2Fstereolith.htm&random=6125http://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith1.htmhttp://computer.howstuffworks.com/stereolith2.htmhttp://computer.howstuffworks.com/stereolith3.htmhttp://computer.howstuffworks.com/stereolith4.htmhttp://computer.howstuffworks.com/stereolith5.htmhttp://videos.howstuffworks.com/computerhttp://videos.howstuffworks.com/computerhttp://www.howstuffworks.com/index.htmhttp://www.howstuffworks.com/index.htmhttp://www.howstuffworks.com/index.htmhttp://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://computer.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.3dsystems.com/http://computer.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.3dsystems.com/http://computer.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.3dsystems.com/http://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0http://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0http://videos.howstuffworks.com/computerhttp://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0http://computer.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.3dsystems.com/http://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://www.howstuffworks.com/index.htmhttp://videos.howstuffworks.com/computerhttp://computer.howstuffworks.com/stereolith5.htmhttp://computer.howstuffworks.com/stereolith4.htmhttp://computer.howstuffworks.com/stereolith3.htmhttp://computer.howstuffworks.com/stereolith2.htmhttp://computer.howstuffworks.com/stereolith1.htmhttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/rate.htm?id=%2Fstereolith.htm&random=6125http://computer.howstuffworks.com/stereolith.htmhttp://computer.howstuffworks.com/stereolith.htm/printablehttp://computer.howstuffworks.com/about-author.htm#brain -
7/29/2019 howstereolithography3-100112180735-phpapp01
2/6
3-D Systems stereolithography machine at PT CAM.
See morepictures of stereolithography.
This machine has four important parts:
A tank filled with several gallons of liquid photopolymer. The photopolymer is a clear, liquid
plastic.
A perforated platform immersed in the tank. The platform can move up and down in the tank
as the printing process proceeds.
An ultraviolet laser
A computer that drives the laser and the platform
The photopolymer is sensitive to ultraviolet light, so when the laser touches the photopolymer, the
polymer hardens.
If you stand next to the stereolithograph apparatus (SLA), you can actually see the laser as it builds
each layer.This short MPEG file lets you see the laser building a small section of a model.The Stereolithography Process
The basic printing process goes like this: You create a 3-D model of your object in a CAD program A piece of software chops your CAD model up into thin layers -- typically five to 10
layers/millimeter
The 3-D printer's laser "paints" one of the layers, exposing the liquid plastic in the tank and
hardening it
http://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0http://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0http://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0http://static.howstuffworks.com/mpeg/stereolith1.mpghttp://static.howstuffworks.com/mpeg/stereolith1.mpghttp://static.howstuffworks.com/mpeg/stereolith1.mpghttp://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0http://static.howstuffworks.com/mpeg/stereolith1.mpghttp://computer.howstuffworks.com/enlarge-image.htm?terms=stereolithography+-robots&page=0 -
7/29/2019 howstereolithography3-100112180735-phpapp01
3/6
The platform drops down into the tank a fraction of a millimeter and the laser paints the next
layer
This process repeats, layer by layer, until your model is complete
This is not a particularly quick process. Depending on the size and number of objects being created, the
laser might take a minute or two for each layer. A typical run might take six to 12 hours. Runs over
several days are possible for large objects (maximum size for the machine shown above is an object 10inches (25 cm) in three dimensions).
A typical CAD drawing ready to be rendered on the 3-D printer.This particular piece is a plastic money clip that PT CAM givesaway to visitors. Note the supports (in red) that separate the
money clip from the tray and support it is it is being built. About50 of these money clips can be created in a single run.
You start by creating a 3-D design for your object in a CAD program. This design is tweaked before
building with supports that raise it up off the tray slightly and with any internal bracing that is required
during building. The SLA then renders the object automatically (and unattended). When the process is
complete, the SLA raises the platform and you end up with your 3-D object. If the object is small, you can
produce several of them at the same time if you like. They all sit next to each other on the tray.
-
7/29/2019 howstereolithography3-100112180735-phpapp01
4/6
The platform in the tank of photopolymer at the beginning of a
print run.
The following photo shows a tray after building is complete, with several identical objects that were
produced simultaneously:
The platform at the end of a print run, shown here withseveral identical objects.
Once the run is complete, you rinse the objects with a solvent and then "bake" them in an ultraviolet oven
that thoroughly cures the plastic.
-
7/29/2019 howstereolithography3-100112180735-phpapp01
5/6
The ultraviolet "oven" used to cure completed objects.
What You Can Create with Stereolithography
Stereolithography allows you to create almost any 3-D shape you can imagine. If you can get it into a
CAD program, you can probably create it. The only caveat is the need for structural integrity during the
building process. In some cases, you need to add internal bracing to a design so that it does not collapse
during the printing or curing phases. The photo below shows you a typical object that has been created at PT CAM. The piece is lightweight
and has the strength of polystyrene plastic. You can mount it, drill it, etc., so you can try it out in actual
use. For example, a chair manufacturer will produce different arm rest shapes using stereolithography
and try them out on actual chairs to see how they feel. This is a close-up of an engine manifold:
-
7/29/2019 howstereolithography3-100112180735-phpapp01
6/6
For more detail on the manifold, seethis short video.
Costs of Stereolithography
Stereolithography is not an inexpensive process. The machines themselves usually cost in excess of
$250,000. They have to be vented because of fumes created by the polymer and the solvents. The
polymer itself is extremely expensive. CibaTool SL5170 resin, a common photopolymer used in
stereolithography, typically costs about $800/gallon. For these reasons, it is uncommon to find
stereolithography machines anywhere but in large companies. However, there are service bureaus that can make the advantages of stereolithography available to
smaller shops and individuals. For example,PT CAMwill do stereolithography for $55/hour, as well as
allowing companies to purchase blocks of time for as low as $30/hour. That's not cheap, but compared to
purchasing your own SLA and resin or having parts machined, it is a real bargain. You can e-mail your
CAD design to PT CAM and, in many cases, get your parts shipped back to you in a day or two. The
short cycle time is one of the most appealing things about stereolithography!Special thanks to Joel Leonard, Jerry Watkins and Steve Oneyear for their help in creating this article!
http://static.howstuffworks.com/mpeg/stereolith2.mpghttp://static.howstuffworks.com/mpeg/stereolith2.mpghttp://static.howstuffworks.com/mpeg/stereolith2.mpghttp://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://www.howstuffworks.com/framed.htm?parent=stereolith.htm&url=http://www.ptcam.com/http://static.howstuffworks.com/mpeg/stereolith2.mpg