humrc tm series master development system user's guide · using the programming dock snap a...

HumRCTM Series Master Development System

User's Guide

Table of Contents 1 Introduction 2 Ordering Information 3 HumRCTM Series Transceiver Carrier Board 3 HumRCTM Series Transceiver Carrier Board Objects 3 HumRCTM Series Transceiver Carrier Board Pin Assignments 4 Programming Dock 4 Programming Dock Objects 5 Remote Control Demo Board 5 Remote Control Demo Board Objects 6 Prototype Board 6 Prototype Board Objects 7 Initial Setup 8 Using the Programming Dock 9 Using the Remote Control Demo Board 11 Using the Prototype Board 14 The Development Kit Demonstration Software 23 Development Kit Demonstration Software Example 31 Carrier Board Schematic 32 Remote Control Demo Board Schematic 36 Programming Dock Board Schematic 40 Prototype Board Schematic 43 Notes

Warning: Some customers may want Linx radio frequency (“RF”) products to control machinery or devices remotely, including machinery or devices that can cause death, bodily injuries, and/or property damage if improperly or inadvertently triggered, particularly in industrial settings or other applications implicating life-safety concerns (“Life and Property Safety Situations”).

NO OEM LINX REMOTE CONTROL OR FUNCTION MODULE SHOULD EVER BE USED IN LIFE AND PROPERTY SAFETY SITUATIONS. No OEM Linx Remote Control or Function Module should be modified for Life and Property Safety Situations. Such modification cannot provide sufficient safety and will void the product’s regulatory certification and warranty.

Customers may use our (non-Function) Modules, Antenna and Connectors as part of other systems in Life Safety Situations, but only with necessary and industry appropriate redundancies and in compliance with applicable safety standards, including without limitation, ANSI and NFPA standards. It is solely the responsibility of any Linx customer who uses one or more of these products to incorporate appropriate redundancies and safety standards for the Life and Property Safety Situation application.

Do not use this or any Linx product to trigger an action directly from the data line or RSSI lines without a protocol or encoder/decoder to validate the data. Without validation, any signal from another unrelated transmitter in the environment received by the module could inadvertently trigger the action.

All RF products are susceptible to RF interference that can prevent communication. RF products without frequency agility or hopping implemented are more subject to interference. This module does have a frequency hopping protocol built in, but the developer should still be aware of the risk of interference.

Do not use any Linx product over the limits in this data guide. Excessive voltage or extended operation at the maximum voltage could cause product failure. Exceeding the reflow temperature profile could cause product failure which is not immediately evident.

Do not make any physical or electrical modifications to any Linx product. This will void the warranty and regulatory and UL certifications and may cause product failure which is not immediately evident.

!

– –1

IntroductionThe Linx HumRCTM Series Remote Control Transceiver modules offer a simple, efficient and cost-effective method of adding remote control capabilities to any product. The Master Development System provides a designer with all the tools necessary to correctly and legally incorporate the module into an end product. The boards serve several important functions:

• Rapid Module Evaluation: The boards allow the performance of the Linx HumRC™ Series modules to be evaluated quickly in a user’s environment. The development boards can be used to evaluate the range performance of the modules.

• Application Development: A prototyping board allows the development of custom circuits directly on the board. All signal lines are available on headers for easy access.

• Software Development: A programming dock with a PC interface allows development and testing of custom software applications for control of the module.

• Design Benchmark: The boards provide a known benchmark against which the performance of a custom design may be judged.

The Master Development System includes 2 Carrier Boards, 2 RC Demo Boards, 2 Programming Dock Boards, 2 Prototype Boards 4 HumRC™ Series transceivers*, antennas, batteries and full documentation.

* One part is soldered to each Carrier Board

HumRCTM Master Development System

User's Guide

Figure 1: HumRCTM Series Master Development System

Revised 8/30/2017

– – – –2 3

HumRCTM Series Transceiver Carrier Board Objects1. HumRCTM Series Transceiver2. MMCX RF Connector3. Dual Row Header4. Single Row Header

HumRCTM Series Transceiver Carrier BoardOrdering Information

Figure 2: Ordering Information

Figure 3: HumRCTM Series Transceiver Carrier Board

1

2

3 4

HumRCTM Series Transceiver Carrier Board Pin Assignments

Figure 4: HumRCTM Series Transceiver Carrier Board Pin Assignments (Top View)

7 MODE_IND9 CMD_DATA_IN11 LATCH_EN13 ACK_EN15 CMD_DATA_OUT17 VCC19 C021 C123 NC25 NC27 NC29 NC31 NC33 NC35 NC37 NC

GND 6RESET 8

PDN 10NC 12

PAIR 14LNA_EN 16

LVL_ADJ 18PA_EN 20

NC 22NC 24NC 26NC 28NC 30NC 32NC 34NC 36

41 S342 S443 S544 S645 S746 ACK_OUT47 NC48 NC49 NC50 NC51 NC52 NC53 NC54 NC55 NC56 NC

40 S239 S138 S0

ANTENNA 1 2-5 GND (RF Connector)

Ordering Information

Part Number Description

EVAL-***-RC HumRCTM Series Basic Evaluation Kit

MDEV-***-RC HumRCTM Series Master Development System

HUM-***-RC HumRCTM Series Remote Control Transceiver

HUM-900-RC-UFL HumRCTM Series Remote Control Transceiver, Certified, UFL Connector

HUM-900-RC-CAS HumRCTM Series Remote Control Transceiver, Certified, Castella-tion Connection

EVM-***-RC HumRCTM Series Carrier Board

EVM-900-RC-UFL HumRCTM Series Carrier Board with Certified module, UFL Con-nector

EVM-900-RC-CAS HumRCTM Series Carrier Board with Certified module, Castellation Connection

MDEV-DEMO-RC-A Development System Remote Control Demo Board, Type A

MDEV-DEMO-RC-B Development System Remote Control Demo Board, Type B

MDEV-PGDOCK Development System Programming Dock

MDEV-PROTO Development System Prototype Board

CON-SOC-EVM EVM Module Socket Kit

*** = Frequency; 900MHz, 2.4GHz

– – – –4 5

1

Remote Control Demo Board

Board BBoard A

Remote Control Demo Board Objects1. Carrier Board Socket2. RP-SMA Antenna Connector3. Power Switch4. MODE_IND LED5. CONFIRM LED6. PAIR button7. Status Line Output LEDs8. Status Line Input Buttons9. 4 AAA Batteries (Not shown, on the back of the boards)

Figure 6: Remote Control Demo Board

1

2

34

5

67

8

1

2

34

5

67

8

Programming Dock

Programming Dock Objects1. Carrier Board Socket2. RP-SMA Antenna Connector3. MODE_IND LED4. Micro USB Connector5. LCD Display

Figure 5: Programming Dock

2

3

4

5

1

– – – –6 7

Prototype Board

Prototype Board Objects1. Carrier Board Socket2. RP-SMA Antenna Connector3. Micro USB Connector4. Power Switch5. Power LED6. External Battery Connection7. Prototyping Area8. 3.3V Supply Bus9. Ground Bus10. USB Interface Lines11. Module Interface Headers12. Command Data Interface Routing Switches (on back)

Figure 7: Prototype Board

4

1

23

10

6

7

8

11

5

9

11

11

12

Initial SetupThere are several boards that are included with the Development System. The Carrier Boards have a HumRCTM Series transceiver on a daughter board with headers. These boards snap into sockets on the other boards, enabling the modules to be easily moved among the test boards.

There are two Programming Docks that have a socket for a Carrier Board and a USB interface for connection to a PC. This is used with the demonstration software included with the kit to configure the module through its Command Data Interface.

There are two Remote Control Demo Boards that are populated differently. Board A has the buttons on the right column and board B has them on the left column. These accept the Carrier Boards and are used to demonstrate the remote control functionality of the HumRCTM Series. They can also be used for range testing. These boards use hardware configuration, so if any changes have been made to the modules using the software then they may not operate correctly. A restore to default configuration can be used to reset the modules.

There are two Prototype Boards that have a socket for a Carrier Board, a USB interface and a large area of plated through holes that can be used to develop custom circuitry. The board can be powered either from the USB connection or an external battery.

The development software supports Windows 7 and 10; with Java 1.6 or later.

Warning: Installing or removing a Carrier Board while power is applied could cause permanent damage to the module. Either turn off power to the board or unplug the USB cable before installing or removing a Carrier Board

!

– – – –8 9

Using the Programming DockSnap a Carrier Board onto the socket on the Programming Dock as shown in Figure 8.

Connect a micro USB cable into the connector at the top of the board. Plug the other end into a PC. The board is powered by the USB bus. The demonstration software included with the kit or custom application software can be used to configure the module through its Command Data Interface. The LCD is used to display information about the module. This includes the module’s local address and a custom nickname. The nickname is entered using the development kit software and can be any name that helps distinguish the modules from one another. This is convenient when multiple programming docks are connected to the same computer. Please see the development kit software section for more information on the nicknames.

The HumRCTM Series transceiver has a serial Command Data Interface that offers the option to configure and control the transceiver through software instead of through hardware. This interface consists of a standard UART with a serial command set. This allows for fewer connections in applications controlled by a microcontroller as well as for more control and advanced features than can be offered through hardware pins alone.

Figure 8: Programming Dock with a Carrier Board

Using the Remote Control Demo BoardSnap a Carrier Board onto the socket on each Remote Control Demo Board as shown in Figure 9.

Insert 4 AAA batteries into the holders on the back of each board, connect antennas and turn on power.

The modules come paired out of the box, but to Pair additional modules, press the PAIR button on both boards. The MODE_IND LEDs flash to indicate that the modules are searching for each other and exchanging addresses. The MODE_IND has a quick flash while searching (100ms on, 900ms off) and a longer flash once Pairing is complete (400ms on, 100ms off). This process only takes a few seconds. The pairing process takes the status line input / output directions into account. If these are changed then the modules should be paired again.

Once complete, pressing a button on one board (the Initiating Unit or IU) causes an LED to light up on the other board (the Responding Unit or RU). The RU sends an acknowledgement message to the IU. If the message is valid, the IU turns on the CONFIRM LED.

Figure 9: Remote Control Demo Board with a Carrier Board

Note: To restore the default configuration, push the PAIR button four times and hold it down on the fifth press. The MODE_IND LED flashes when it has reset.

– – – –10 11

Range TestingSeveral complex mathematical models exist for determining path loss in many environments. These models vary as the transmitter and receiver are moved from indoor operation to outdoor operation. Although these models can provide an estimation of range performance in the field, the most reliable method is to simply perform range tests using the modules in the intended operational environment.

Range testing can be performed with the Remote Control Demo Boards. To prepare the board for range testing, simply turn it on by switching the power switch to the ON position. Pressing a status line button on one board (the IU) activates an LED on the other board (the RU). The RU then sends an acknowledgement back to the IU, which turns on the CONFIRM LED. This indicates good bi-directional RF communications and lets the user set one board down and walk with the other board.

As the maximum range of the link in the test area is approached, it is not uncommon for the signal to cut in and out as the radio moves. This is normal and can result from other interfering sources or fluctuating signal levels due to multipath effects. This results in cancellation of the transmitted signal as direct and reflected signals arrive at the receiver at differing times and phases. The areas in which this occurs are commonly called “nulls” and simply walking a little farther usually restores the signal. If the signal is not restored, then the maximum range of the link has been reached.

To achieve maximum range, keep objects such as your hand away from the antenna and ensure that the antenna on the transmitter has a clear and unobstructed line-of-sight path to the receiver board. Range performance is determined by many interdependent factors. If the range you are able to achieve is significantly less than specified by Linx for the products you are testing, then there is likely a problem with either the board or the ambient RF environment in which the board is operating. First, check the battery, switch positions, and antenna connection. Next, measure the receiver’s RSSI voltage with the transmitter turned off to determine if ambient interference is present. High RSSI readings while the transmitter off indicate there is interference. If this fails to resolve the issue, please contact Linx technical support.

Note: The Remote Control Demo boards are designed for hardware configuration. If the modules are changed through software configuration then the boards may not operate as expected. A restore to default configuration can be used to reset the modules.

Using the Prototype BoardSnap a Carrier Board onto the socket on the Prototype Board as shown in Figure 10.

Place the power switch into the “USB” position then connect a micro USB cable into the connector at the top of the board. Plug the other end into a PC or any USB charger. The board is powered by the USB bus. This board features a prototyping area to facilitate the addition of application-specific circuitry. The prototyping area contains a large area of plated through-holes so that external circuitry can be placed on the board. The holes are set at 0.100” on center with a 0.040” diameter, accommodating most industry-standard SIP and DIP packages.

At the top of the prototyping area is a row connected to the 3.3V power supply and at the bottom is a row connected to ground. External circuitry can be interfaced to the transceiver through the breakout headers. The numbers next to the headers correspond to the pin numbers on the Carrier Board. Figure 4 shows the pin assignments for the Carrier Board.

The OVERLOAD LED indicates that that too much current is being pulled from the USB bus. This is used to prevent damage to the parts or the bus. The overload condition is reset once the excess current draw is removed.

Figure 10: Prototype Board with a Carrier Board

– – – –12 13

Supply for the module is connected through R17. This can be removed and replaced by another supply or used to measure the current consumption of the module.

Figure 11 shows the bottom of the board.

SW1 and SW2 connect the USB interface to the Command Data Interface lines on the module. This allows the prototype board to be used with the development kit software or a custom application. When in the “USB Connected position”, the module is connected to the USB interface. The “Header Only” position connects the module to the header.

Footprints for 0603 size resistors are on most lines so that pull-ups or pull-downs can easily be added to the lines. The pads are connected to VCC or GND based on the most common configuration for the module. The schematic at the end of this document shows how each line is connected.

Note: The onboard 3.3-volt regulator has approximately 400mA available for additional circuitry when plugged into a PC. If more current is required, the user must power the board from an external supply or a USB charger with more current capabilities, up to 1A.

Figure 11: Prototype Board Bottom Side

The LADJ line has pads for both a pull up and pull down resistor. This can be populated based on the needs of the specific module that is connected to the prototype board. The HumRCTM Series uses both resistors to create a voltage divider that determines the output power level. Please see the HumRCTM data guide for more details on this.

Figure 12 shows a convenient cross reference showing which lines on the module connect to which lines on the prototype board.

Module to Prototype Board Pin Number Cross Reference

Pin Name Module Pin Number Prototype Board Pin Number

MODE_IND 30 7

RESET 22 8

CMD_DATA_IN 27 9

POWER_DOWN 12 10

LATCH_EN 13 11

ACK_EN 28 13

PAIR 29 14

CMD_DATA_OUT 26 15

VCC 21 17

LVL_ADJ 32 18

C0 10 19

C1 11 21

S0 8 38

S1 7 39

S2 6 40

S3 5 41

S4 4 42

S5 3 43

S6 2 44

S7 1 45

ACK_OUT 31 46

Figure 12: Module to Prototype Board Pin Number Cross Reference

– – – –14 15

The Development Kit Demonstration SoftwareThe development kit includes software that is used to configure and control the module through the Programming Dock. The software defaults to the Demo & EZConfiguration tab when opened (Figure 13). This window offers basic configuration and demonstration of the module’s functionality with the current configuration.

1. Clicking the Contact Linx, Documentation and About labels on the left side expands them to show additional information and links to the latest documentation. This is shown in Figure 15.

2. The Help window shows tips and comments about the software.

3. The active module is connected to the PC and being configured by the software.

4. Available modules are connected to the PC but are not currently being configured or controlled by the PC

5. Known Modules are not currently connected to the PC, but have either been connected to the software in the past or have been manually entered.

6. The Given Permissions window shows the list of modules that are paired with the active module and the Permissions Mask for each one.

7. The demo area replicates a remote control device. The appearance changes with the programmed configurations.

7

4

1

2

3

106

8

11

5

9

Figure 13: The Master Development System Software Demo and EZConfiguration Tab

8. The Status Details section shows the module’s control line states, radio state and RSSI level.

9. The Sent and Received Packets window shows the commands sent to the module and the responses from the module. This aids in debugging custom software.

10. Once a module has been configured, the configurations can be saved into a profile that can be recalled and programmed into other modules. The Saved Profiles list shows all of the profiles that have been saved into the software.

11. The Show Commands button opens a larger window to view the serial commands sent to and received from the module.

The modules are shown with three identifiers as shown in Figure 14.

1. The type of module (HumRC™ Series)

2. The module’s local address.

3. A custom name that can be given to the module. Type a name into the box and press Enter to apply it. This name is shown on the LCD display on the programming dock.

Figure 14: The Master Development System Software Module Identifiers

12 3

Figure 15: The Master Development System Software Additional Information

– – – –16 17

The Advanced Configuration tab (Figure 16) offers more detailed configuration options for the active module.

1. The Local Address box shows the module’s local address in hexadecimal format. This can be changed by typing a new hex value.

2. The Status Line Mask sets the status lines as either inputs or outputs. If the box is checked then the line is an input.

3. The Latch Mask determines if the status line outputs are latched or momentary. If the box is checked then the output is latched. This setting has no effect on lines that are configured as inputs.

4. The Paired Modules Window lists all of the modules that are paired with the active module and their Permissions Mask.

5. The Address box enables manual pairing of a module. Enter an address into this box and press the Set Module button to add the address to the list.

6. The Permissions Mask determines whether a specific module is authorized to control a specific status line output. If the box is checked then the module is authorized to control that line.

Figure 16: The Master Development System Software Advanced Configuration Tab

7

4

123

10

6

8

115

9

12

13

14

1617

18

15

19 20

7. The Set Module button adds the address and Permissions Mask to the list. If a current module is selected, then the Permissions can be updated. The Remove module button removes the selected module from the list. The Remove All Modules button removes all of the modules from the list.

8. The Interrupt Mask sets the conditions under which an interrupt is to be generated on the CMD_DATA_OUT line. The Message Select menu sets the type of message that triggers the interrupt when the Selected Message Ready box is checked.

9. The TX Power Level Source configures how the transmitter output power is set. It uses either the voltage on the LVL_ADJ line or the value in the box. The accepted range of values is -20 to +12.

10. The Transmitter Mode selection sets whether the module transmits command messages when a status line input is asserted or when it receives a software command.

11. The Receiver Mode selection turns the receiver on or off for power savings. If the module is set as an Initiating Unit only with all status lines as inputs, then the receiver is disabled by default.

12. The Status Line Direction selection sets how the status lines are configured as inputs and outputs. Either the C0 and C1 hardware lines are used to set them in groups of 4 or the Status Line Mask is used to set them individually.

13. The Latch Status Outputs selection configures how the latched or momentary operation for each status line output is set. Either the LATCH_EN hardware line is used to set all of the lines the same way or the Latch Mask is used to set the lines individually.

14. If the Respond to Request Remote Sample is enabled, the module automatically responds to the request with a packet than contains the values determined by the MType field in the received packet.

15. The Custom Data box enables a custom 2-byte value to be loaded into the module to be transmitted with each control message or Acknowledge with Data packet.

16. The Duty Cycle configuration sets the interval and Keep on times for automatically cycling power to the receiver.

17. The Module Identity box displays the module type, firmware version and serial number of the active module.

18. The Read All button reads all of the current configurations from the active module.

– – – –18 19

19. The Submit button writes all changes to the active module.

20. The Set Defaults button restores the active module to factory default conditions.

The Command Set tab (Figure 17) allows specific commands to be written to the module.

1. The Command box shows the hexadecimal values that are written to the module. Values can be typed into the box or a command can be selected from the Commands menu.

2. The Response box shows the hexadecimal values that are returned from the module in response to a command.

3. The Commands drop-down menu shows all of the commands that are available for the active module (Figure 18). Selecting one of the commands from this menu automatically fills in the Command box. The values can be adjusted by typing in the box.

4

1

2 3

6

5

Figure 17: The Master Development System Software Command Set Tab

4. The Items drop down menu displays all of the items that are available for the active module (Figure 19). Selecting one of the items from this menu automatically fills in the Command box. The values can be adjusted by typing in the box.

5. Clicking the Send button writes the values in the Command box to the module.

6. The structure of the selected command and its response is shown in the main window. Please see the HumRC™ Series Transceiver Command Data Interface Reference Guide for definitions of each value.

Figure 19: The Master Development System Software Demo Command Set Tab Items Menu

Figure 18: The Master Development System Software Demo Command Set Tab Commands Menu

– – – –20 21

The Sandbox tab shows the interaction of all of the connected modules on one screen. Figure 20 shows two modules on the screen, but up to 8 modules can fit at one time.

Clicking a button on one device causes the module to transmit control messages. Paired modules with appropriate Permissions Mask settings activate and their status is updated in the software. Paired modules that are not connected to the PC can activate a module that is connected and the connected module’s status is reflected in the software.

The Sandbox is a convenient place to show the interaction of multiple units in one location, but it is a reflection of actual module operation. It is not a simulation.

Figure 20: The Master Development System Software Sandbox Tab

The RC Configuration tab (Figure 21) allows configuration of the module’s advanced remote control features.

1. The Analog Inputs Source area configures which lines are analog inputs, the number of readings to average, the reference voltage and the offset for each channel.

2. The Custom Data Source menu sets the source of custom data transmitted with each IU message.

3. The Trigger Operation area configures which lines are triggered inputs, their type of control, session duration and transmit interval.

4. The NV Memory Cycles show how many times data has been written to the module’s non-volatile memory. The module is capable of approximately 1,000 writes to NV memory before it wears out. This count gives an indication of how many more times the module can be written.

5. The Analog Input Readings show the current analog measurements.6. The Trigger Input Status shows the current states of the trigger lines.

Figure 21: The Master Development System Software RC Configuration Tab

7

4

1

2

3

10

6

8

11

5

9 12

– – – –22 23

7. The Pairing Status area shows the current status of any pairing operations.

8. The request Remote Sample configures the module to request a response from a remote unit. This area configures the type of sample that should be in the response and the address of the unit that should respond.

9. The Read All button reads all of the current configurations from the active module.

10. The Submit button writes all changes to the active module.

11. The Set Defaults button restores the active module to factory default conditions.

12. The Commit button writes any changed configurations to non-volatile memory. The changes should be written to the module using the Submit button first, then the Commit button is used to make the changes permanent.

Development Kit Demonstration Software ExampleThis example shows how to configure two modules to work with each other. The software defaults to the Demo & EZConfiguration tab when opened (Figure 22).

Install Carrier Boards onto the Programming Docks and plug a USB cable between the Programming Docks and the PC. The software automatically detects attached devices. The first module that is identified appears under the Active label. This is the module that is actively controlled by the software. Subsequent modules are listed under the Available label as shown in Figure 23.

Modules must be paired with the active device. This is accomplished by dragging modules from the Available or Known Modules lists to the Given Permissions window as shown in Figure 24.

Figure 22: The Master Development System Software Demo and EZConfiguration Tab

Figure 23: The Master Development System Software Connected Modules

– – – –24 25

Once the module is dropped into the Given Permissions window it is written to the active module’s memory. Clicking on the down arrow displays the paired module’s Permissions Mask. This configures which output lines the paired module is authorized to control. In Figure 25 the Permissions are inactive since the active module only has inputs and no outputs to control.

Figure 25: The Master Development System Software Paired Modules

Figure 24: The Master Development System Software Pairing Modules

Changing the active module is accomplished by dragging a module from the Available list to the Active spot, as shown in Figure 26.

With the new module active, drag the original module to the Given Permissions window. Click on the Advanced Configuration tab (Figure 27).

Figure 26: The Master Development System Software Changing the Active Module

Figure 27: The Master Development System Software Advanced Configuration

– – – –26 27

This tab shows the advanced configurations enabled by the module’s Command Data Interface. Any changes are highlighted in red. In the example in Figure 28 the output mask has been changed to all inputs, S0 is latched, the Paired module is given full permissions, the status line direction is set by the mask and the outputs are latched by the Latch Mask. Clicking the Set Module button sets the updated Permissions Mask. Clicking the Submit button writes all of the changes to the module’s memory.

This configuration changes the module to have all outputs. This is shown by clicking on the Demo & EZConfiguration tab Figure 29.

Figure 28: The Master Development System Software Advanced Configuration with Changes

The buttons have all changed to LEDs. The symbol next to each LED indicates if it is latching or momentary (Figure 30). S0 is latching, the rest are momentary.

Now that the modules are configured their use can be demonstrated. Clicking a button on the transmitter module activates an LED on the receiving module. Figure 31 shows the transmitter, Figure 32 shows the receiver.

Figure 29: The Master Development System Software Demo and EZConfiguration Tab with Changes

Figure 30: The Master Development System Software Latching (1) and Momentary (2) Symbols

1 2

– – – –28 29

Figure 31: The Master Development System Software Transmitting Module

Figure 32: The Master Development System Software Receiving Module

Full system operation is demonstrated by clicking on the Sandbox tab (Figure 33).

These configurations can be saved as a profile for recalling or programming into other modules. The Demo & EZConfiguration tab has the profile window (Figure 34).

Clicking the Save Current button brings up a prompt asking for a name of the profile (Figure 35).

Figure 33: The Master Development System Software Sandbox

Figure 34: The Master Development System Software Saved Profiles Window

– – – –30 31

Once saved, the profile appears in the window, as shown in Figure 36.

To apply a profile, select it from a list and click the Program button. Clicking the Remove button removes it from the list.

Figure 35: The Master Development System Software Save Profile

Figure 36: The Master Development System Software with a Saved Profile

S7

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

AC

K_O

UT

S0

S1

S2

S3

S4

S5

S6

S7

PA

IR

MO

DE

_IN

D

LAT

CH

_EN

AC

K_E

N

RE

SE

TP

DN

LAD

J

CM

D_D

AT

A_I

N

CM

D_D

AT

A_O

UT

LNA

_EN

PAIR

PA_EN

RESET PDN

LAD

J

LNA_EN

MO

DE

_IN

D

LATCH_EN

ACK_EN

AC

K_O

UT

S0

S1

S2

S3

S4

S5

S6

S7

C0

C1

C0

C1

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

J1 Car

rier

Inte

rcon

nect

CMD_DATA_OUT

CMD_DATA_IN

X1

X2

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

GN

D

VC

C

VC

C

PA

_EN

GN

D17

VCC21

GN

D18

RESET22

LNA_EN23

PA_EN24

CMD_DATA_OUT26

CMD_DATA_IN27

ACK_EN28

PAIR29

S6

2

GND25

1

MO

DE

_IN

D30

AC

K_O

UT

31

LVL_

AD

J32

S5

3

S4

4

AN

T19

GN

D20

S35

S26

S17

S08

C010

C111

POWER_DOWN12

LATCH_EN13

GND9

GN

D16

GN

D15

GN

D14

TR

1X

3

GN

D

5.3n

H

0 oh

m

1.2p

F

X2

X3

X1

2.4G

Hz

900M

Hz

DN

P

DN

P

DN

P

Figure 37: HumRCTM Series Transceiver Carrier Board Module Schematic

Carrier Board Schematic

– – – –32 33

Remote Control Demo Board Schematic

123

P2

Header 3

D4D5D6

1234

P1

Header 4

D0D1D2D3

GND

R2330

VCC

D1

PO

WE

R G

RE

EN

MO

DE

_IN

D

GND

R3330

D2

MO

DE

_IN

D B

LUE

CO

NF

IRM

GND

R27330

D20

CO

NF

IRM

RE

D

RF1

GN

D2-

5

ANT1CONREVSMA002

PAIR

MODE_IND

CONFIRM

LATCH_EN

D0D1D2D3D4D5

ACK_ENPDN

CMD_DATA_IN

CMD_DATA_OUTD6D7

SER_I/O

C0C1SEND

CRT_LRN

GND

GND

VCC

GND GND

GND

GND

12 3

4 5

6 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556

J1Carrier Interconnect Female

LVL_ADJ IDENTITY

GND

X2

DNP

X1

1.8nH

ED_SEL

SEL_TIMER

D8D9D_CFGA_CFG_0A_CFG_1

BAUD_0

GND

SW1SPDT

GND

VCC

B1

GND

Vin1

GN

D2

Vout3

U1

C10.47uF

GND

+ C2

100uF

VDD1

RA52

RA43

MCLR4

RC55

RC46

RC37

RC28

RC19

RC010

RA211

ICSPCLK12

ICSPDAT13

GND14

U2

PIC16F1824

VCC GNDPGDPGC

MCLR

CMD_DATA_INCMD_DATA_OUT

IDENTITY CRT_LRNMODE_IND

GND

SER_I/O

R14330

GND

S9RESTORE

D7

RE

ST

OR

E C

OM

PLE

TE

GR

EE

N

PIC A/B

R360

R330

VCC

GND

SW2

LVL_ADJ

AC

K_E

NR

320

VCC

R34

10K

GND

BA

UD

_0

IDE

NT

ITY

SE

L_T

IME

R

SE

ND

LAT

CH

_EN

PD

NR

80

R38

10K

R37

10K

R35

10K

R9

10K

D8

D9

R41

10K

R42

10K

D_C

FG

A_C

GF

_0

A_C

FG

_1

R6

10K

R5

10K

R4

10K

GND

VCC

S8PAIR

R110K

PAIR CRT_LRN

REMOTE CONTROL AREAPOWER SUPPLY AREA

RF MODULE AREA

MISC CIRCUITS

MICROCONTROLLER AREA

123

P3

Header 3

D7

VCC

GND 1234

J2

MCLR

PGD56

PGC

VCCGND

VCCS0

D0

SE

ND

D5

R12330

D3

R1010K

GND

GND

VCCS1

D1

SE

ND

R17330

R1510K

GND

GND

D10

D8

VCCS2

D2

SE

ND

R21330

R1910K

GND

GND

D14

D12

VCCS3

D3

SE

ND

R25330

R2310K

GND

GND

D18

D16

VCCS4

D4

SE

ND

R13330

R1110K

GND

GND

D6

D4

VCCS5

D5

SE

ND

R18330

R1610K

GND

GND

D11

D9

VCCS6

D6

SE

ND

R22330

R2010K

GND

GND

D15

D13

VCCS7

D7

SE

ND

R26330

R2410K

GND

GND

D19

D17

C0

C1 GND

VCCR30 0 ohm

R31 0 ohm

ED_SELR7 10K

R39 0 ohm GND

GND

PIC A/B

C0

C1

R28 0 ohm GND

VCCR29 0 ohm

R40 0 ohm VCC

ED_SELR43 10K

VCC

PIC A/B

A Board B Board A Board

Figure 38: Remote Control Demo Board Microcontroller Area Schematic

Note: The Remote Control Demo boards are designed to accept carrier boards for multiple module families. Some circuitry is not applicable for some modules.

123

P2

Header 3

D4D5D6

1234

P1

Header 4

D0D1D2D3

GND

R2330

VCC

D1

PO

WE

R G

RE

EN

MO

DE

_IN

D

GND

R3330

D2

MO

DE

_IN

D B

LUE

CO

NF

IRM

GND

R27330

D20

CO

NF

IRM

RE

D

RF1

GN

D2-

5

ANT1CONREVSMA002

PAIR

MODE_IND

CONFIRM

LATCH_EN

D0D1D2D3D4D5

ACK_ENPDN

CMD_DATA_IN

CMD_DATA_OUTD6D7

SER_I/O

C0C1SEND

CRT_LRN

GND

GND

VCC

GND GND

GND

GND

12 3

4 5

6 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556


LVL_ADJ IDENTITY

GND

X2

DNP

X1

1.8nH

ED_SEL

SEL_TIMER


BAUD_0

GND

SW1SPDT

GND

VCC

B1

GND

Vin1

GN

D2

Vout3

U1

C10.47uF

GND

+ C2

100uF

VDD1

RA52

RA43

MCLR4

RC55

RC46

RC37

RC28

RC19

RC010

RA211

ICSPCLK12

ICSPDAT13

GND14

U2

PIC16F1824

VCC GNDPGDPGC

MCLR



GND

SER_I/O

R14330

GND

S9RESTORE

D7

RE

ST

OR

E C

OM

PLE

TE

GR

EE

N

PIC A/B

R360

R330

VCC

GND

SW2

LVL_ADJ

AC

K_E

NR

320

VCC

R34

10K

GND

BA

UD

_0

IDE

NT

ITY

SE

L_T

IME

R

SE

ND

LAT

CH

_EN

PD

NR

80

R38

10K

R37

10K

R35

10K

R9

10K

D8

D9

R41

10K

R42

10K

D_C

FG

A_C

GF

_0

A_C

FG

_1

R6

10K

R5

10K

R4

10K

GND

VCC

S8PAIR

R110K

PAIR CRT_LRN


RF MODULE AREA

MISC CIRCUITS


123

P3

Header 3

D7

VCC

GND 1234

J2

MCLR

PGD56

PGC

VCCGND

VCCS0

D0

SE

ND

D5

R12330

D3

R1010K

GND

GND

VCCS1

D1

SE

ND

R17330

R1510K

GND

GND

D10

D8

VCCS2

D2

SE

ND

R21330

R1910K

GND

GND

D14

D12

VCCS3

D3

SE

ND

R25330

R2310K

GND

GND

D18

D16

VCCS4

D4

SE

ND

R13330

R1110K

GND

GND

D6

D4

VCCS5

D5

SE

ND

R18330

R1610K

GND

GND

D11

D9

VCCS6

D6

SE

ND

R22330

R2010K

GND

GND

D15

D13

VCCS7

D7

SE

ND

R26330

R2410K

GND

GND

D19

D17

C0

C1 GND

VCCR30 0 ohm

R31 0 ohm

ED_SELR7 10K

R39 0 ohm GND

GND

PIC A/B

C0

C1

R28 0 ohm GND

VCCR29 0 ohm

R40 0 ohm VCC

ED_SELR43 10K

VCC

PIC A/B


Figure 39: Remote Control Demo Board Power Supply Area Schematic

123

P2

Header 3

D4D5D6

1234

P1

Header 4

D0D1D2D3

GND

R2330

VCC

D1

PO

WE

R G

RE

EN

MO

DE

_IN

D

GND

R3330

D2

MO

DE

_IN

D B

LUE

CO

NF

IRM

GND

R27330

D20

CO

NF

IRM

RE

D

RF1

GN

D2-

5

ANT1CONREVSMA002

PAIR

MODE_IND

CONFIRM

LATCH_EN

D0D1D2D3D4D5

ACK_ENPDN

CMD_DATA_IN

CMD_DATA_OUTD6D7

SER_I/O

C0C1SEND

CRT_LRN

GND

GND

VCC

GND GND

GND

GND

12 3

4 5

6 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556


LVL_ADJ IDENTITY

GND

X2

DNP

X1

1.8nH

ED_SEL

SEL_TIMER


BAUD_0

GND

SW1SPDT

GND

VCC

B1

GND

Vin1

GN

D2

Vout3

U1

C10.47uF

GND

+ C2

100uF

VDD1

RA52

RA43

MCLR4

RC55

RC46

RC37

RC28

RC19

RC010

RA211

ICSPCLK12

ICSPDAT13

GND14

U2

PIC16F1824

VCC GNDPGDPGC

MCLR



GND

SER_I/O

R14330

GND

S9RESTORE

D7

RE

ST

OR

E C

OM

PLE

TE

GR

EE

N

PIC A/B

R360

R330

VCC

GND

SW2

LVL_ADJ

AC

K_E

NR

320

VCC

R34

10K

GND

BA

UD

_0

IDE

NT

ITY

SE

L_T

IME

R

SE

ND

LAT

CH

_EN

PD

NR

80

R38

10K

R37

10K

R35

10K

R9

10K

D8

D9

R41

10K

R42

10K

D_C

FG

A_C

GF

_0

A_C

FG

_1

R6

10K

R5

10K

R4

10K

GND

VCC

S8PAIR

R110K

PAIR CRT_LRN


RF MODULE AREA

MISC CIRCUITS


123

P3

Header 3

D7

VCC

GND 1234

J2

MCLR

PGD56

PGC

VCCGND

VCCS0

D0

SE

ND

D5

R12330

D3

R1010K

GND

GND

VCCS1

D1

SE

ND

R17330

R1510K

GND

GND

D10

D8

VCCS2

D2

SE

ND

R21330

R1910K

GND

GND

D14

D12

VCCS3

D3

SE

ND

R25330

R2310K

GND

GND

D18

D16

VCCS4

D4

SE

ND

R13330

R1110K

GND

GND

D6

D4

VCCS5

D5

SE

ND

R18330

R1610K

GND

GND

D11

D9

VCCS6

D6

SE

ND

R22330

R2010K

GND

GND

D15

D13

VCCS7

D7

SE

ND

R26330

R2410K

GND

GND

D19

D17

C0

C1 GND

VCCR30 0 ohm

R31 0 ohm

ED_SELR7 10K

R39 0 ohm GND

GND

PIC A/B

C0

C1

R28 0 ohm GND

VCCR29 0 ohm

R40 0 ohm VCC

ED_SELR43 10K

VCC

PIC A/B


Figure 40: Remote Control Demo Board RF Carrier Area Schematic

– – – –34 35

123

P2

Header 3

D4D5D6

1234

P1

Header 4

D0D1D2D3

GND

R2330

VCC

D1

PO

WE

R G

RE

EN

MO

DE

_IN

D

GND

R3330

D2

MO

DE

_IN

D B

LUE

CO

NF

IRM

GND

R27330

D20

CO

NF

IRM

RE

D

RF1

GN

D2-

5

ANT1CONREVSMA002

PAIR

MODE_IND

CONFIRM

LATCH_EN

D0D1D2D3D4D5

ACK_ENPDN

CMD_DATA_IN

CMD_DATA_OUTD6D7

SER_I/O

C0C1SEND

CRT_LRN

GND

GND

VCC

GND GND

GND

GND

12 3

4 5

6 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556


LVL_ADJ IDENTITY

GND

X2

DNP

X1

1.8nH

ED_SEL

SEL_TIMER


BAUD_0

GND

SW1SPDT

GND

VCC

B1

GND

Vin1

GN

D2

Vout3

U1

C10.47uF

GND

+ C2

100uF

VDD1

RA52

RA43

MCLR4

RC55

RC46

RC37

RC28

RC19

RC010

RA211

ICSPCLK12

ICSPDAT13

GND14

U2

PIC16F1824

VCC GNDPGDPGC

MCLR



GND

SER_I/O

R14330

GND

S9RESTORE

D7

RE

ST

OR

E C

OM

PLE

TE

GR

EE

N

PIC A/B

R360

R330

VCC

GND

SW2

LVL_ADJ

AC

K_E

NR

320

VCC

R34

10K

GND

BA

UD

_0

IDE

NT

ITY

SE

L_T

IME

R

SE

ND

LAT

CH

_EN

PD

NR

80

R38

10K

R37

10K

R35

10K

R9

10K

D8

D9

R41

10K

R42

10K

D_C

FG

A_C

GF

_0

A_C

FG

_1

R6

10K

R5

10K

R4

10K

GND

VCC

S8PAIR

R110K

PAIR CRT_LRN


RF MODULE AREA

MISC CIRCUITS


123

P3

Header 3

D7

VCC

GND 1234

J2

MCLR

PGD56

PGC

VCCGND

VCCS0

D0

SE

ND

D5

R12330

D3

R1010K

GND

GND

VCCS1

D1

SE

ND

R17330

R1510K

GND

GND

D10

D8

VCCS2

D2

SE

ND

R21330

R1910K

GND

GND

D14

D12

VCCS3

D3

SE

ND

R25330

R2310K

GND

GND

D18

D16

VCCS4

D4

SE

ND

R13330

R1110K

GND

GND

D6

D4

VCCS5

D5

SE

ND

R18330

R1610K

GND

GND

D11

D9

VCCS6D

6

SE

ND

R22330

R2010K

GND

GND

D15

D13

VCCS7

D7

SE

ND

R26330

R2410K

GND

GND

D19

D17

C0

C1 GND

VCCR30 0 ohm

R31 0 ohm

ED_SELR7 10K

R39 0 ohm GND

GND

PIC A/B

C0

C1

R28 0 ohm GND

VCCR29 0 ohm

R40 0 ohm VCC

ED_SELR43 10K

VCC

PIC A/B


Figure 41: Remote Control Demo Board Remote Control Area Schematic

123

P2

Header 3

D4D5D6

1234

P1

Header 4

D0D1D2D3

GND

R2330

VCC

D1

PO

WE

R G

RE

EN

MO

DE

_IN

D

GND

R3330

D2

MO

DE

_IN

D B

LUE

CO

NF

IRM

GND

R27330

D20

CO

NF

IRM

RE

D

RF1

GN

D2-

5

ANT1CONREVSMA002

PAIR

MODE_IND

CONFIRM

LATCH_EN

D0D1D2D3D4D5

ACK_ENPDN

CMD_DATA_IN

CMD_DATA_OUTD6D7

SER_I/O

C0C1SEND

CRT_LRN

GND

GND

VCC

GND GND

GND

GND

12 3

4 5

6 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556


LVL_ADJ IDENTITY

GND

X2

DNP

X1

1.8nH

ED_SEL

SEL_TIMER


BAUD_0

GND

SW1SPDT

GND

VCC

B1

GND

Vin1

GN

D2

Vout3

U1

C10.47uF

GND

+ C2

100uF

VDD1

RA52

RA43

MCLR4

RC55

RC46

RC37

RC28

RC19

RC010

RA211

ICSPCLK12

ICSPDAT13

GND14

U2

PIC16F1824

VCC GNDPGDPGC

MCLR



GND

SER_I/O

R14330

GND

S9RESTORE

D7

RE

ST

OR

E C

OM

PLE

TE

GR

EE

N

PIC A/B

R360

R330

VCC

GND

SW2

LVL_ADJ

AC

K_E

NR

320

VCC

R34

10K

GND

BA

UD

_0

IDE

NT

ITY

SE

L_T

IME

R

SE

ND

LAT

CH

_EN

PD

NR

80

R38

10K

R37

10K

R35

10K

R9

10K

D8

D9

R41

10K

R42

10K

D_C

FG

A_C

GF

_0

A_C

FG

_1

R6

10K

R5

10K

R4

10K

GND

VCC

S8PAIR

R110K

PAIR CRT_LRN


RF MODULE AREA

MISC CIRCUITS


123

P3

Header 3

D7

VCC

GND 1234

J2

MCLR

PGD56

PGC

VCCGND

VCCS0

D0

SE

ND

D5

R12330

D3

R1010K

GND

GND

VCCS1D

1

SE

ND

R17330

R1510K

GND

GND

D10

D8

VCCS2

D2

SE

ND

R21330

R1910K

GND

GND

D14

D12

VCCS3

D3

SE

ND

R25330

R2310K

GND

GND

D18

D16

VCCS4

D4

SE

ND

R13330

R1110K

GND

GND

D6

D4

VCCS5

D5

SE

ND

R18330

R1610K

GND

GND

D11

D9

VCCS6

D6

SE

ND

R22330

R2010K

GND

GND

D15

D13

VCCS7

D7

SE

ND

R26330

R2410K

GND

GND

D19

D17

C0

C1 GND

VCCR30 0 ohm

R31 0 ohm

ED_SELR7 10K

R39 0 ohm GND

GND

PIC A/B

C0

C1

R28 0 ohm GND

VCCR29 0 ohm

R40 0 ohm VCC

ED_SELR43 10K

VCC

PIC A/B


Figure 42: Remote Control Demo Board Miscellaneous Circuits Schematic

– – – –36 37

GND

+ C8

100uF

VCC

GND

Vin1

GN

D2

Vout 3

U4LM3940IMP 3.3V

C90.47uF

GND

IN1

GND2

EN3 FAULT 4

ILIM 5

OUT 6

U3TPS2552

GND

5VUSB

GND

R1153.6kPWREN#

USB AREA POWER SUPPLY AREA RF MODULE CARRIER AREA

SIGNAL ROUTING

U8

VDC1

RA52

RA43

MCLR4

RC55

RC46

RC37 RC2 8RC1 9RC0 10RA2 11ICSPCLK 12ICSPDAT 13GND 14

PIC16F1825-I/ST

VCC GND

PGM

CSB RSSISCLRSTPGCPGD

R42 DNP

VCCP

VCC

RS

SISCL

RST

CSB

VCC

GND

GNDC131uF

GND

C141uF C1-2

C1+3

VOUT4

VCC5

GND6

SI7

SCL8

CSB9

RS10

LED+1

LED-12

RST11

LCD1

2x16 LCD

R60 Ohm


D2

GN

D

GN

D

+C

14.

7uF

C4

0.01

uF

L1 600R

/1.3

A

GN

D

C6

47pF

R4

0

C2

0.1u

F

VCC12

VCCIO3

3V3O

UT

10

GND 5

GND 13

US

BD

M9

US

BD

P8

RE

SE

T#11

TXD

1

RX

D4

RTS

#2

CTS

#6

CB

US

015

CB

US

114

CB

US

27

CB

US

316

U2

FT23

0X

C5

47pF

PW

RE

N#

C7

0.1u

F

GN

D

5V1

DA

T-

2

DA

T+3

NC

4

GSHD 6GSHD 7

GN

D5

J1 Mic

ro U

SB

5VU

SB

RTS

R2

27

R3

27

TXD

RX

D

nCTS

VC

C R20

10k

R47

DN

P

GP

IO2

RX

TXLE

D

D1

R5330 ohm

OR

AN

GE

RX

TXLE

D

VCC

R1710k

GND

NC1

IN2

GND3 OUT 4

VCC 5U5 VCC

GND

R49 DNPBuffer Bypass DNP

RTS nCMD

CMD_DATA_OUTRXD

NC1

IN2

GND3 OUT 4

VCC 5U1 VCC

GND

R4610k

VCC

R48 DNPCMD_DATA_INTXD

Buffer Bypass DNP

GND

MO

DE

_IN

D

R8330 ohm

D4

MO

DE

_IN

D B

LUE

R2410k

S2

VCC

PA

IR

PAIR

GND

R410 ohm

R400 ohm

VCC

GND

SW1

LADJ

R36DNP

R23DNP

GPIO1

RXD

GND

nPDN

R9

10k

GN

D

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

D

GN

DG

ND

R35

10k

R34

10k

R33

10k

R32

10k

R30

10k

R28

10k

R22

10k

R21

10k

R18

10k

R15

10k

R14

10k

R13

10k

R12

10k

R10

10k

GN

DR

3810

kV

CC

R16

10k

VC

C

VC

C R1

1 O

hm

MODE_INDCMD_DATA_IN

CM

D_D

ATA

_OU

T

GN

D

GN

D

GN

DG

ND

GN

D

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

J2 Car

rier I

nter

conn

ectR29

10k

GN

D

GN

DV

CC

VC

CR

2710

kR

2510

k

R19

10k

R31

10k

VC

C

PA

IR

GN

DR

2610

kG

ND

R37

10k

GN

DR

3910

kG

ND

R43

10k

R44

10k

GN

DR

4510

kG

ND

RF

1

GND 2-5

AN

T1

GN

DG

ND

X1

1nH

X3

DN

P

GN

DX2

DN

P

LAD

J

nPD

NnC

MD

nCTS

CMD_DATA_IN

GP

IO1

GP

IO2

GP

IO1

Figure 43: Programming Dock Board RF Carrier Area Schematic

Programming Dock Board Schematic

GND

+ C8

100uF

VCC

GND

Vin1

GN

D2

Vout 3

U4LM3940IMP 3.3V

C90.47uF

GND

IN1

GND2

EN3 FAULT 4

ILIM 5

OUT 6

U3TPS2552

GND

5VUSB

GND

R1153.6kPWREN#


SIGNAL ROUTING

U8

VDC1

RA52

RA43

MCLR4

RC55

RC46


PIC16F1825-I/ST

VCC GND

PGM


R42 DNP

VCCP

VCC

RS

SISCL

RST

CSB

VCC

GND

GNDC131uF

GND

C141uF C1-2

C1+3

VOUT4

VCC5

GND6

SI7

SCL8

CSB9

RS10

LED+1

LED-12

RST11

LCD1

2x16 LCD

R60 Ohm


D2

GN

D

GN

D

+C

14.

7uF

C4

0.01

uF

L1 600R

/1.3

A

GN

D

C6

47pF

R4

0

C2

0.1u

F

VCC12

VCCIO3

3V3O

UT

10

GND 5

GND 13

US

BD

M9

US

BD

P8

RE

SE

T#11

TXD

1

RX

D4

RTS

#2

CTS

#6

CB

US

015

CB

US

114

CB

US

27

CB

US

316

U2

FT23

0X

C5

47pF

PW

RE

N#

C7

0.1u

F

GN

D

5V1

DA

T-

2

DA

T+3

NC

4

GSHD 6GSHD 7

GN

D5

J1 Mic

ro U

SB

5VU

SB

RTS

R2

27

R3

27

TXD

RX

D

nCTS

VC

C R20

10k

R47

DN

P

GP

IO2

RX

TXLE

D

D1

R5330 ohm

OR

AN

GE

RX

TXLE

D

VCC

R1710k

GND

NC1

IN2

GND3 OUT 4

VCC 5U5 VCC

GND


RTS nCMD

CMD_DATA_OUTRXD

NC1

IN2

GND3 OUT 4

VCC 5U1 VCC

GND

R4610k

VCC


Buffer Bypass DNP

GND

MO

DE

_IN

D

R8330 ohm

D4

MO

DE

_IN

D B

LUE

R2410k

S2

VCC

PA

IR

PAIR

GND

R410 ohm

R400 ohm

VCC

GND

SW1

LADJ

R36DNP

R23DNP

GPIO1

RXD

GND

nPDN

R9

10k

GN

D

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

D

GN

DG

ND

R35

10k

R34

10k

R33

10k

R32

10k

R30

10k

R28

10k

R22

10k

R21

10k

R18

10k

R15

10k

R14

10k

R13

10k

R12

10k

R10

10k

GN

DR

3810

kV

CC

R16

10k

VC

C

VC

C R1

1 O

hm

MODE_INDCMD_DATA_IN

CM

D_D

ATA

_OU

T

GN

D

GN

D

GN

DG

ND

GN

D

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

J2 Car

rier I

nter

conn

ectR29

10k

GN

D

GN

DV

CC

VC

CR

2710

kR

2510

k

R19

10k

R31

10k

VC

C

PA

IR

GN

DR

2610

kG

ND

R37

10k

GN

DR

3910

kG

ND

R43

10k

R44

10k

GN

DR

4510

kG

ND

RF

1

GND 2-5

AN

T1

GN

DG

ND

X1

1nH

X3

DN

P

GN

DX2

DN

P

LAD

J

nPD

NnC

MD

nCTS

CMD_DATA_IN

GP

IO1

GP

IO2

GP

IO1

Figure 44: Programming Dock Board Power Supply Area Schematic

GND

+ C8

100uF

VCC

GND

Vin1

GN

D2

Vout 3

U4LM3940IMP 3.3V

C90.47uF

GND

IN1

GND2

EN3 FAULT 4

ILIM 5

OUT 6

U3TPS2552

GND

5VUSB

GND

R1153.6kPWREN#


SIGNAL ROUTING

U8

VDC1

RA52

RA43

MCLR4

RC55

RC46


PIC16F1825-I/ST

VCC GND

PGM


R42 DNP

VCCP

VCC

RS

SISCL

RST

CSB

VCC

GND

GNDC131uF

GND

C141uF C1-2

C1+3

VOUT4

VCC5

GND6

SI7

SCL8

CSB9

RS10

LED+1

LED-12

RST11

LCD1

2x16 LCD

R60 Ohm


D2

GN

D

GN

D

+C

14.

7uF

C4

0.01

uF

L1 600R

/1.3

A

GN

D

C6

47pF

R4

0

C2

0.1u

F

VCC12

VCCIO3

3V3O

UT

10

GND 5

GND 13

US

BD

M9

US

BD

P8

RE

SE

T#11

TXD

1

RX

D4

RTS

#2

CTS

#6

CB

US

015

CB

US

114

CB

US

27

CB

US

316

U2

FT23

0X

C5

47pF

PW

RE

N#

C7

0.1u

F

GN

D

5V1

DA

T-

2

DA

T+3

NC

4

GSHD 6GSHD 7

GN

D5

J1 Mic

ro U

SB

5VU

SB

RTS

R2

27

R3

27

TXD

RX

D

nCTS

VC

C R20

10k

R47

DN

P

GP

IO2

RX

TXLE

D

D1

R5330 ohm

OR

AN

GE

RX

TXLE

D

VCC

R1710k

GND

NC1

IN2

GND3 OUT 4

VCC 5U5 VCC

GND


RTS nCMD

CMD_DATA_OUTRXD

NC1

IN2

GND3 OUT 4

VCC 5U1 VCC

GND

R4610k

VCC


Buffer Bypass DNP

GND

MO

DE

_IN

D

R8330 ohm

D4

MO

DE

_IN

D B

LUE

R2410k

S2

VCC

PA

IR

PAIR

GND

R410 ohm

R400 ohm

VCC

GND

SW1

LADJ

R36DNP

R23DNP

GPIO1

RXD

GND

nPDN

R9

10k

GN

D

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

D

GN

DG

ND

R35

10k

R34

10k

R33

10k

R32

10k

R30

10k

R28

10k

R22

10k

R21

10k

R18

10k

R15

10k

R14

10k

R13

10k

R12

10k

R10

10k

GN

DR

3810

kV

CC

R16

10k

VC

C

VC

C R1

1 O

hm

MODE_INDCMD_DATA_IN

CM

D_D

ATA

_OU

T

GN

D

GN

D

GN

DG

ND

GN

D

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

J2 Car

rier I

nter

conn

ectR29

10k

GN

D

GN

DV

CC

VC

CR

2710

kR

2510

k

R19

10k

R31

10k

VC

C

PA

IR

GN

DR

2610

kG

ND

R37

10k

GN

DR

3910

kG

ND

R43

10k

R44

10k

GN

DR

4510

kG

ND

RF

1

GND 2-5

AN

T1

GN

DG

ND

X1

1nH

X3

DN

P

GN

DX2

DN

P

LAD

J

nPD

NnC

MD

nCTS

CMD_DATA_IN

GP

IO1

GP

IO2

GP

IO1

Figure 45: Programming Dock Board Signal Routing Schematic

– – – –38 39

GND

+ C8

100uF

VCC

GND

Vin1

GN

D2

Vout 3

U4LM3940IMP 3.3V

C90.47uF

GND

IN1

GND2

EN3 FAULT 4

ILIM 5

OUT 6

U3TPS2552

GND

5VUSB

GND

R1153.6kPWREN#


SIGNAL ROUTING

U8

VDC1

RA52

RA43

MCLR4

RC55

RC46


PIC16F1825-I/ST

VCC GND

PGM


R42 DNP

VCCP

VCC

RS

SISCL

RST

CSB

VCC

GND

GNDC131uF

GND

C141uF C1-2

C1+3

VOUT4

VCC5

GND6

SI7

SCL8

CSB9

RS10

LED+1

LED-12

RST11

LCD1

2x16 LCD

R60 Ohm


D2

GN

D

GN

D

+C

14.

7uF

C4

0.01

uF

L1 600R

/1.3

A

GN

D

C6

47pF

R4

0

C2

0.1u

F

VCC12

VCCIO3

3V3O

UT

10

GND 5

GND 13

US

BD

M9

US

BD

P8

RE

SE

T#11

TXD

1

RX

D4

RTS

#2

CTS

#6

CB

US

015

CB

US

114

CB

US

27

CB

US

316

U2

FT23

0X

C5

47pF

PW

RE

N#

C7

0.1u

F

GN

D

5V1

DA

T-

2

DA

T+3

NC

4

GSHD 6GSHD 7

GN

D5

J1 Mic

ro U

SB

5VU

SB

RTS

R2

27

R3

27

TXD

RX

D

nCTS

VC

C R20

10k

R47

DN

P

GP

IO2

RX

TXLE

D

D1

R5330 ohm

OR

AN

GE

RX

TXLE

D

VCC

R1710k

GND

NC1

IN2

GND3 OUT 4

VCC 5U5 VCC

GND


RTS nCMD

CMD_DATA_OUTRXD

NC1

IN2

GND3 OUT 4

VCC 5U1 VCC

GND

R4610k

VCC


Buffer Bypass DNP

GND

MO

DE

_IN

D

R8330 ohm

D4

MO

DE

_IN

D B

LUE

R2410k

S2

VCC

PA

IR

PAIR

GND

R410 ohm

R400 ohm

VCC

GND

SW1

LADJ

R36DNP

R23DNP

GPIO1

RXD

GND

nPDN

R9

10k

GN

D

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

D

GN

DG

ND

R35

10k

R34

10k

R33

10k

R32

10k

R30

10k

R28

10k

R22

10k

R21

10k

R18

10k

R15

10k

R14

10k

R13

10k

R12

10k

R10

10k

GN

DR

3810

kV

CC

R16

10k

VC

C

VC

C R1

1 O

hm

MODE_INDCMD_DATA_IN

CM

D_D

ATA

_OU

T

GN

D

GN

D

GN

DG

ND

GN

D

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

J2 Car

rier I

nter

conn

ectR29

10k

GN

D

GN

DV

CC

VC

CR

2710

kR

2510

k

R19

10k

R31

10k

VC

C

PA

IR

GN

DR

2610

kG

ND

R37

10k

GN

DR

3910

kG

ND

R43

10k

R44

10k

GN

DR

4510

kG

ND

RF

1

GND 2-5

AN

T1

GN

DG

ND

X1

1nH

X3

DN

P

GN

DX2

DN

P

LAD

J

nPD

NnC

MD

nCTS

CMD_DATA_IN

GP

IO1

GP

IO2

GP

IO1

Figure 46: Programming Dock Board USB Area Schematic

GND

+ C8

100uF

VCC

GND

Vin1

GN

D2

Vout 3

U4LM3940IMP 3.3V

C90.47uF

GND

IN1

GND2

EN3 FAULT 4

ILIM 5

OUT 6

U3TPS2552

GND

5VUSB

GND

R1153.6kPWREN#


SIGNAL ROUTING

U8

VDC1

RA52

RA43

MCLR4

RC55

RC46


PIC16F1825-I/ST

VCC GND

PGM


R42 DNP

VCCP

VCC

RS

SISCL

RST

CSB

VCC

GND

GNDC131uF

GND

C141uF C1-2

C1+3

VOUT4

VCC5

GND6

SI7

SCL8

CSB9

RS10

LED+1

LED-12

RST11

LCD1

2x16 LCD

R60 Ohm


D2

GN

D

GN

D

+C

14.

7uF

C4

0.01

uF

L1 600R

/1.3

A

GN

D

C6

47pF

R4

0

C2

0.1u

F

VCC12

VCCIO3

3V3O

UT

10

GND 5

GND 13

US

BD

M9

US

BD

P8

RE

SE

T#11

TXD

1

RX

D4

RTS

#2

CTS

#6

CB

US

015

CB

US

114

CB

US

27

CB

US

316

U2

FT23

0X

C5

47pF

PW

RE

N#

C7

0.1u

F

GN

D

5V1

DA

T-

2

DA

T+3

NC

4

GSHD 6GSHD 7

GN

D5

J1 Mic

ro U

SB

5VU

SB

RTS

R2

27

R3

27

TXD

RX

D

nCTS

VC

C R20

10k

R47

DN

P

GP

IO2

RX

TXLE

D

D1

R5330 ohm

OR

AN

GE

RX

TXLE

D

VCC

R1710k

GND

NC1

IN2

GND3 OUT 4

VCC 5U5 VCC

GND


RTS nCMD

CMD_DATA_OUTRXD

NC1

IN2

GND3 OUT 4

VCC 5U1 VCC

GND

R4610k

VCC


Buffer Bypass DNP

GND

MO

DE

_IN

D

R8330 ohm

D4

MO

DE

_IN

D B

LUE

R2410k

S2

VCC

PA

IR

PAIR

GND

R410 ohm

R400 ohm

VCC

GND

SW1

LADJ

R36DNP

R23DNP

GPIO1

RXD

GND

nPDN

R9

10k

GN

D

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

D

GN

DG

ND

R35

10k

R34

10k

R33

10k

R32

10k

R30

10k

R28

10k

R22

10k

R21

10k

R18

10k

R15

10k

R14

10k

R13

10k

R12

10k

R10

10k

GN

DR

3810

kV

CC

R16

10k

VC

C

VC

C R1

1 O

hm

MODE_INDCMD_DATA_IN

CM

D_D

ATA

_OU

T

GN

D

GN

D

GN

DG

ND

GN

D

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

J2 Car

rier I

nter

conn

ectR29

10k

GN

D

GN

DV

CC

VC

CR

2710

kR

2510

k

R19

10k

R31

10k

VC

C

PA

IR

GN

DR

2610

kG

ND

R37

10k

GN

DR

3910

kG

ND

R43

10k

R44

10k

GN

DR

4510

kG

ND

RF

1

GND 2-5

AN

T1

GN

DG

ND

X1

1nH

X3

DN

P

GN

DX2

DN

P

LAD

J

nPD

NnC

MD

nCTS

CMD_DATA_IN

GP

IO1

GP

IO2

GP

IO1

Figure 47: Programming Dock Board Microcontroller Area Schematic

– – – –40 41

GN

D

OU

TIN

GND

GND

+

C7

10uF

THERM

4

123

U5

THERM

RF

12 3

4 5

6 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556


1

GN

D2-

5

ANT1CONREVSMA001

GND

GND

GND

GND

GND

78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556

X1

0 Ohm

6

X3DNP

GNDGND

X2DNP

GND

R24330

5VUSB

D2

PO

WE

R (G

RE

EN

)

D3

OV

ER

CU

RR

EN

T (R

ED

)

R22330

VCC

FAULT

U2

R5

10k

GND

5VUSB

GND

C80.47uF

FAU

LT

IN1

GND2

EN3 FAULT 4

ILIM 5

OUT 6

TPS2553

SW3

5VUSB

EN

FAULT

GND12

J3

100mil HeaderBattery Input

D1

GND

R753.6k

R953.6k

GND

Q1

R310k

BCD Charger

VCC

+

GND

GND

C14.7uF

C3

0.01uF

L1600R/1.3A

GND

C5

47pF

R40

C20.1uF

VC

C12

VC

CIO

3

3V3OUT10

GN

D5

GN

D13

USBDM9

USBDP8

RESET11

TXD 1

RXD 4

RTS 2

CTS 6

CBUS0 15

CBUS1 14

CBUS2 7

CBUS3 16

U6

FT230X

C4

47pF

C60.1uF

GND

5V 1

DAT- 2

DAT+ 3

NC 4

GS

HD

6G

SH

D7

GND 5

J1 Micro USB

RTSCTS

R1 27

R2 27

5VUSB

EN

BCD Charger

TXD

RXD

SW1

SW2

9

15

CMD_DATA_IN

CMD_DATA_OUT

NC1

IN2

GND3 OUT 4

VCC 5U3 VCC

GND

R25DNP

VCC

R27 DNP

NC 1

IN 2

GND 3OUT4

VCC5

U4

R33DNP

GND

VCC

R36 DNP

PROTOTYPEAREA

GND BUS

1

TXD

RX

DR

TSC

TS

VCC BUS

1

TP3

1

TP2

GND GND

TP1

VCC

39404142434445

4647484950515253545556

38373635

293031

323334

78910111213141516171819202122232425262728

1 2 3 4

J6100mil Header

1234567891011121314151617181920212223242526

J5100mil Header

GND

VCC

R10 DNPVCC

123456789

1011

J7100mil Header

123456789

1011121314

J4100mil Header

R45 DNP GND

R44 DNPR43 DNPR42 DNPR41 DNPR40 DNPR39 DNPR38 DNP

GNDGNDGNDGNDGNDGNDGND

GNDR52 DNPR53 DNP GND

R19 DNPGND

VCC

R11 DNPGND

R50 DNP GND

R14 DNPGND

R17 0 ohmVCC

R12 DNPGND

R26 DNP

R23 DNPGND

R21 DNPGND R47 DNP GNDR48 DNP GNDR49 DNP GND

R15DNP

VCC

R18DNP

GND

R13 DNP

R8 DNP

R16 DNPGND

R20 DNPGND

R28 DNPGND R29 DNPVCC R30 DNPGND R31 DNPGND

R32 DNP GND

R34 DNP GNDR35 DNP GND

R54 DNP GNDR55 DNP GNDR56 DNP VCC

C9

0.1uF

GND

VCC

6R6 DNP

Figure 48: Prototype Board Power Supply Area Schematic

GN

D

OU

TIN

GND

GND

+

C7

10uF

THERM

4

123

U5

THERM

RF

12 3

4 5

6 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556


1

GN

D2-

5

ANT1CONREVSMA001

GND

GND

GND

GND

GND

78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132 3334 3536 37

38394041424344454647484950515253545556

X1

0 Ohm

6

X3DNP

GNDGND

X2DNP

GND

R24330

5VUSB

D2

PO

WE

R (G

RE

EN

)

D3

OV

ER

CU

RR

EN

T (R

ED

)

R22330

VCC

FAULT

U2

R5

10k

GND

5VUSB

GND

C80.47uF

FAU

LT

IN1

GND2

EN3 FAULT 4

ILIM 5

OUT 6

TPS2553

SW3

5VUSB

EN

FAULT

GND12

J3

100mil HeaderBattery Input

D1

GND

R753.6k

R953.6k

GND

Q1

R310k

BCD Charger

VCC

+

GND

GND

C14.7uF

C3

0.01uF

L1600R/1.3A

GND

C5

47pF

R40

C20.1uF

VC

C12

VC

CIO

3

3V3OUT10

GN

D5

GN

D13

USBDM9

USBDP8

RESET11

TXD 1

RXD 4

RTS 2

CTS 6

CBUS0 15

CBUS1 14

CBUS2 7

CBUS3 16

U6

FT230X

C4

47pF

C60.1uF

GND

5V 1

DAT- 2

DAT+ 3

NC 4

GS

HD

6G

SH

D7

GND 5

J1 Micro USB

RTSCTS

R1 27

R2 27

5VUSB

EN

BCD Charger

TXD

RXD

SW1

SW2

9

15

CMD_DATA_IN

CMD_DATA_OUT

NC1

IN2

GND3 OUT 4

VCC 5U3 VCC

GND

R25DNP

VCC

R27 DNP

NC 1

IN 2

GND 3OUT4

VCC5

U4

R33DNP

GND

VCC

R36 DNP

PROTOTYPEAREA

GND BUS

1

TXD

RX

DR

TSC

TS

VCC BUS

1

TP3

1

TP2

GND GND

TP1

VCC

39404142434445

4647484950515253545556

38373635

293031

323334

78910111213141516171819202122232425262728

1 2 3 4

J6100mil Header

1234567891011121314151617181920212223242526

J5100mil Header

GND

VCC

R10 DNPVCC

123456789

1011

J7100mil Header

123456789

1011121314

J4100mil Header

R45 DNP GND

R44 DNPR43 DNPR42 DNPR41 DNPR40 DNPR39 DNPR38 DNP

GNDGNDGNDGNDGNDGNDGND

GNDR52 DNPR53 DNP GND

R19 DNPGND

VCC

R11 DNPGND

R50 DNP GND

R14 DNPGND

R17 0 ohmVCC

R12 DNPGND

R26 DNP

R23 DNPGND

R21 DNPGND R47 DNP GNDR48 DNP GNDR49 DNP GND

R15DNP

VCC

R18DNP

GND

R13 DNP

R8 DNP

R16 DNPGND

R20 DNPGND

R28 DNPGND R29 DNPVCC R30 DNPGND R31 DNPGND

R32 DNP GND

R34 DNP GNDR35 DNP GND

R54 DNP GNDR55 DNP GNDR56 DNP VCC

C9

0.1uF

GND

VCC

6R6 DNP

Figure 49: Prototype Board RF Carrier Area Schematic

Prototype Board Schematic

GND

OUT

IN

GN

D

GN

D

+

C7

10uF

THE

RM

4

1

2

3

U5

THE

RM

RF

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

J2 Car

rier I

nter

conn

ect F

emal

e1

GND 2-5

AN

T1C

ON

RE

VS

MA

001

GN

D

GN

D

GN

D

GN

D

GN

D

78

910

1112

1314

1516

1718

1920

2122

2324

2526

2728

2930

3132

3334

3536

37

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

X1

0 O

hm

6

X3

DN

P

GN

DG

NDX

2D

NP

GN

D

R24

330

5VU

SB

D2

POWER (GREEN)

D3

OVER CURRENT (RED)

R22

330

VC

C

FAU

LT

U2

R5

10k

GN

D 5VU

SB

GN

D

C8

0.47

uF

FAULT

IN1

GN

D2

EN

3FA

ULT

4

ILIM

5

OU

T6

TPS

2553

SW

3

5VU

SB

EN

FAU

LT

GN

D1 2

J3

100m

il H

eade

rB

atte

ry In

put

D1

GN

D

R7 53.6

kR

9 53.6

k

GN

DQ1

R3

10k

BC

D C

harg

er

VC

C

+

GN

D

GN

D

C1

4.7u

F

C3

0.01

uF

L160

0R/1

.3A

GN

D

C5

47pF

R4

0

C2

0.1u

F

VCC12

VCCIO3

3V3O

UT

10

GND 5

GND 13

US

BD

M9

US

BD

P8

RE

SE

T11

TXD

1

RX

D4

RTS

2

CTS

6

CB

US

015

CB

US

114

CB

US

27

CB

US

316

U6

FT23

0X

C4

47pF

C6

0.1u

F

GN

D

5V1

DA

T-

2

DA

T+3

NC

4

GSHD 6GSHD 7

GN

D5

J1M

icro

US

B

RTS

CTS

R1

27

R2

27

5VU

SB

EN

BC

D C

harg

er

TXD RX

D

SW

1 SW

2

9

15

CM

D_D

ATA

_IN

CM

D_D

ATA

_OU

T

NC

1

IN2

GN

D3

OU

T4

VC

C5

U3

VC

C

GN

D

R25

DN

P

VC

C

R27

DN

P

NC

1

IN2

GN

D3

OU

T4

VC

C5

U4

R33

DN

P

GN

DVC

C

R36

DN

P

PR

OTO

TYP

EA

RE

A

GN

D B

US

1

TXDRXDRTSCTS

VC

C B

US

1

TP3

1

TP2

GN

DG

ND

TP1

VC

C

39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 5638373635

29 30 31

32 33 347 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

1234

J6 100m

il H

eade

r1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

J510

0mil

Hea

der

GN

D

VC

C

R10

DN

PV

CC

1 2 3 4 5 6 7 8 9 10 11J7 100m

il H

eade

r

1 2 3 4 5 6 7 8 9 10 11 12 13 14J4 100m

il H

eade

r

R45

DN

PG

ND

R44

DN

PR

43D

NP

R42

DN

PR

41D

NP

R40

DN

PR

39D

NP

R38

DN

P

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

D

GN

DR

52D

NP

R53

DN

PG

ND

R19

DN

PG

ND

VC

C

R11

DN

PG

ND

R50

DN

PG

ND

R14

DN

PG

ND

R17

0 oh

mV

CC

R12

DN

PG

ND

R26

DN

P

R23

DN

PG

ND

R21

DN

PG

ND

R47

DN

PG

ND

R48

DN

PG

ND

R49

DN

PG

ND

R15

DN

P

VC

C R18

DN

P

GN

D

R13

DN

P

R8

DN

P

R16

DN

PG

ND

R20

DN

PG

ND

R28

DN

PG

ND

R29

DN

PV

CC

R30

DN

PG

ND

R31

DN

PG

ND

R32

DN

PG

ND

R34

DN

PG

ND

R35

DN

PG

ND

R54

DN

PG

ND

R55

DN

PG

ND

R56

DN

PV

CC

C9

0.1u

F

GN

D

VC

C

6R

6D

NP

Figure 50: Prototype Board USB Area Schematic

– – – –42 43

GND

OUT

IN

GN

D

GN

D

+

C7

10uF

THE

RM

4

1

2

3

U5

THE

RM

RF

1

23

45

67

89

1011

1213

1415

1617

1819

2021

2223

2425

2627

2829

3031

3233

3435

3637

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

J2 Car

rier I

nter

conn

ect F

emal

e1

GND 2-5

AN

T1C

ON

RE

VS

MA

001

GN

D

GN

D

GN

D

GN

D

GN

D

78

910

1112

1314

1516

1718

1920

2122

2324

2526

2728

2930

3132

3334

3536

37

38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

X1

0 O

hm

6

X3

DN

P

GN

DG

NDX

2D

NP

GN

D

R24

330

5VU

SB

D2

POWER (GREEN)

D3

OVER CURRENT (RED)

R22

330

VC

C

FAU

LT

U2

R5

10k

GN

D 5VU

SB

GN

D

C8

0.47

uF

FAULT

IN1

GN

D2

EN

3FA

ULT

4

ILIM

5

OU

T6

TPS

2553

SW

3

5VU

SB

EN

FAU

LT

GN

D1 2

J3

100m

il H

eade

rB

atte

ry In

put

D1

GN

D

R7 53.6

kR

9 53.6

k

GN

DQ1

R3

10k

BC

D C

harg

er

VC

C

+

GN

D

GN

D

C1

4.7u

F

C3

0.01

uF

L160

0R/1

.3A

GN

D

C5

47pF

R4

0

C2

0.1u

F

VCC12

VCCIO3

3V3O

UT

10

GND 5

GND 13

US

BD

M9

US

BD

P8

RE

SE

T11

TXD

1

RX

D4

RTS

2

CTS

6

CB

US

015

CB

US

114

CB

US

27

CB

US

316

U6

FT23

0X

C4

47pF

C6

0.1u

F

GN

D

5V1

DA

T-

2

DA

T+3

NC

4

GSHD 6GSHD 7

GN

D5

J1M

icro

US

B

RTS

CTS

R1

27

R2

27

5VU

SB

EN

BC

D C

harg

er

TXD RX

D

SW

1 SW

2

9

15

CM

D_D

ATA

_IN

CM

D_D

ATA

_OU

T

NC

1

IN2

GN

D3

OU

T4

VC

C5

U3

VC

C

GN

D

R25

DN

P

VC

C

R27

DN

P

NC

1

IN2

GN

D3

OU

T4

VC

C5

U4

R33

DN

P

GN

DVC

C

R36

DN

P

PR

OTO

TYP

EA

RE

A

GN

D B

US

1

TXDRXDRTSCTS

VC

C B

US

1

TP3

1

TP2

GN

DG

ND

TP1

VC

C

39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 5638373635

29 30 31

32 33 347 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

1234

J6 100m

il H

eade

r1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

J510

0mil

Hea

der

GN

D

VC

C

R10

DN

PV

CC

1 2 3 4 5 6 7 8 9 10 11J7 100m

il H

eade

r

1 2 3 4 5 6 7 8 9 10 11 12 13 14J4 100m

il H

eade

r

R45

DN

PG

ND

R44

DN

PR

43D

NP

R42

DN

PR

41D

NP

R40

DN

PR

39D

NP

R38

DN

P

GN

DG

ND

GN

DG

ND

GN

DG

ND

GN

D

GN

DR

52D

NP

R53

DN

PG

ND

R19

DN

PG

ND

VC

C

R11

DN

PG

ND

R50

DN

PG

ND

R14

DN

PG

ND

R17

0 oh

mV

CC

R12

DN

PG

ND

R26

DN

P

R23

DN

PG

ND

R21

DN

PG

ND

R47

DN

PG

ND

R48

DN

PG

ND

R49

DN

PG

ND

R15

DN

P

VC

C R18

DN

P

GN

D

R13

DN

P

R8

DN

P

R16

DN

PG

ND

R20

DN

PG

ND

R28

DN

PG

ND

R29

DN

PV

CC

R30

DN

PG

ND

R31

DN

PG

ND

R32

DN

PG

ND

R34

DN

PG

ND

R35

DN

PG

ND

R54

DN

PG

ND

R55

DN

PG

ND

R56

DN

PV

CC

C9

0.1u

F

GN

D

VC

C

6R

6D

NP

Figure 51: Prototype Board Prototype Area Schematic

Notes

Disclaimer

Linx Technologies is continually striving to improve the quality and function of its products. For this reason, we reserve the right to make changes to our products without notice. The information contained in this Data Guide is believed to be accurate as of the time of publication. Specifications are based on representative lot samples. Values may vary from lot-to-lot and are not guaranteed. “Typical” parameters can and do vary over lots and application. Linx Technologies makes no guarantee, warranty, or representation regarding the suitability of any product for use in any specific application. It is the customer’s responsibility to verify the suitability of the part for the intended application. NO LINX PRODUCT IS INTENDED FOR USE IN ANY APPLICATION WHERE THE SAFETY OF LIFE OR PROPERTY IS AT RISK.

Linx Technologies DISCLAIMS ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL LINX TECHNOLOGIES BE LIABLE FOR ANY OF CUSTOMER’S INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING IN ANY WAY FROM ANY DEFECTIVE OR NON-CONFORMING PRODUCTS OR FOR ANY OTHER BREACH OF CONTRACT BY LINX TECHNOLOGIES. The limitations on Linx Technologies’ liability are applicable to any and all claims or theories of recovery asserted by Customer, including, without limitation, breach of contract, breach of warranty, strict liability, or negligence. Customer assumes all liability (including, without limitation, liability for injury to person or property, economic loss, or business interruption) for all claims, including claims from third parties, arising from the use of the Products. The Customer will indemnify, defend, protect, and hold harmless Linx Technologies and its officers, employees, subsidiaries, affiliates, distributors, and representatives from and against all claims, damages, actions, suits, proceedings, demands, assessments, adjustments, costs, and expenses incurred by Linx Technologies as a result of or arising from any Products sold by Linx Technologies to Customer. Under no conditions will Linx Technologies be responsible for losses arising from the use or failure of the device in any application, other than the repair, replacement, or refund limited to the original product purchase price. Devices described in this publication may contain proprietary, patented, or copyrighted techniques, components, or materials. Under no circumstances shall any user be conveyed any license or right to the use or ownership of such items.

©2018 Linx Technologies. All rights reserved.

The stylized Linx logo, Wireless Made Simple, WiSE, CipherLinx and the stylized CL logo are trademarks of Linx Technologies.

Linx Technologies

159 Ort Lane

Merlin, OR, US 97532

Phone: +1 541 471 6256

Fax: +1 541 471 6251

www.linxtechnologies.com

humrc tm series master development system user's guide · using the programming dock snap a...

Documents