hush mini - pln group · 2019-02-20 · hush mini designed by david trubridge 1 contents (not to...
TRANSCRIPT
HUSH MINIDesigned by David Trubridge
1 www.plngroup.co.nz
Overall Dimensions - Model: 1034-A (110V)
40 in1000 mm
40 in1000 mm
16 in400 mm
HUSH MINIDesigned by David Trubridge
1 www.plngroup.co.nz
Contents (not to scale)
Please double check all components are present andquantities are correct before beginning assembly
x1 Top Panel Assembly
Mini size: 11 in dia (280 mm)(Power cable not shown)
x20 Tapered
Felt PanelsMini size: 25.6 in long (650mm)
x1 82 in cable
(2.1m)
x40 (+5) Small Ratchet Rivets
(.5 in / 13mm)
x1LED Driver
(PCD-16-700A)
x2Folded
Cardboard Pillars
x40 (+5) Large Ratchet Rivets
(.74in / 19mm)x1
Cone Gripperwith Base
HUSH MINIDesigned by David Trubridge
2 www.plngroup.co.nz
Step 1 - Top Panel Ratchet Rivet Assembly
Screw on x1 Cone Grippers (without bases) onto base
already attached to top panel assembly
Large Ratchet Rivet (.74in / 19mm)
Bend back gently
Insert Large RatchetRivets (.74in / 19mm) in all
holes around edge.
Power Cord
Suspension Wire
(power cord and suspension wires not shown)
HUSH MINIDesigned by David Trubridge
3 www.plngroup.co.nz
x20
Step 2 - Pop out side panel plugs
Push out the 4 plugs perpanel to make way for the
plastic clips.
HUSH MINIDesigned by David Trubridge
4 www.plngroup.co.nz
Click
Click
Click
Step 3 - Top Panel to Side Panel Assembly
Assemble on a large clean surface or on floor.
Large RatchetRivet (.74in / 19mm) x 20
NOTE Ratchet Rivets must be pushed together fully for
maximum strength
NOTE: Do not put ratchet rivet on first panel until all panels have been
clipped on.
Proceed Anti Clockwise
HUSH MINIDesigned by David Trubridge
5 www.plngroup.co.nz
First
Last
Step 4 - Top Panel to Side Panel Assembly Continued
Tuck last panelunder first panel
and clip together with
Large Ratchet Rivet
Cross Section Detail View of Top Panels overlapping.
HUSH MINIDesigned by David Trubridge
6 www.plngroup.co.nz
Box
Step 5 - Lifting into shape
Use suspension cable to lift theHush Mini approximately 16 in (400mm) from the floor/surface.
The panels will begin tofall into their natural shape.
Use the folded cardboardpillar that was in the box (or similar-sized table)to prop it up.
Clean Floor / Table
HUSH MINIDesigned by David Trubridge
7 www.plngroup.co.nz
Step 6A - Weaving of Panels - Exploded Detail
Bold Lines indicate the ‘Ear’ that sits on the outside of the Hush Mini. This weaving pattern is essential to lock the shape together
Once two panels are woven together, use two of the shorter Ratchet Rivets (.5 in / 13 mm) to lock them together.
Click
ClickClick
HUSH MINIDesigned by David Trubridge
8 www.plngroup.co.nz
Step 6A - Weaving of Panels - Finished Detail
Bold Lines indicate the ‘Ear’ that sits on the outside of the Hush Mini. This weaving pattern is essential to lock the shape together
HUSH MINIDesigned by David Trubridge
9 www.plngroup.co.nz
Step 7 - Height Adjustment and Levelling
Ceiling Mounting Point.
If installing into wood use a countersunk timber screw (not supplied) to affix cone gripto ceiling.
If installing into concrete usecountersunk anchor bolt (not supplied) to affix cone gripto ceiling.
To shorten wire:Pull cable through holein side of gripper point
To lengthen wire:Depress cylinder at top
of gripper point and pull wire out
push
HUSH MINIDesigned by David Trubridge
10 www.plngroup.co.nz
Step 8 - Electrics, Suggested LED driver placement with hanging ceiling
Concrete
Hung Ceiling
LED DriverTo Mains Power
IMPORTANT: ENSURE LED DRIVER ANDMAINS CONNECTION ISWIRED BY A CERTIFIED
ELECTRICIAN
SEE APPENDIX 1 FORDRIVER INFORMATION
HUSH MINIDesigned by David Trubridge
11 www.plngroup.co.nz
Appendix 1: LED Driver Diagram
MEANWELL 16W Single Output C Dimmable LED Power Supply(PCD-16-700A)
IMPORTANT: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE
WITH THE APPLICABLE INSTALLATION CODE BY APERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED
AC/N (Blue)
AC/L (Brown)
V- (Black)
V+ (Red)
HUSH MINIDesigned by David Trubridge
12 www.plngroup.co.nz
Appendix 2: Access to LED Lights for maintenance
To gain access to the LEDs, remove the 3 small screws.
HUSH MINIDesigned by David Trubridge
13 www.plngroup.co.nz
Appendix 3: Top Panel Sub Assembly
Aluminium Disk(LEDs on underside)
Plastic Spacer Disk
Felt Panel
3 x .5 in (12mm) Screws
Exploded View Assembled View