M-1

DRAWING NO.

MECHANICAL NOTES,LEGEND AND DRAWING INDEX

DRAWING TITLE

ISSUE

ISSUE FOR BID

10

/11/19

RENOVATIONS TO THE TREDYFFRINTOWNSHIP BUILDING

MEP - DRAWING INDEX

MD-1 MECHANICAL DEMOLITION FLOOR PLAN

M-1.1 MECHANICAL FLOOR PLAN - PHASE 1

P-1.2 PLUMBING FLOOR PLAN - PHASE 2

P-1.3

GENERAL SPECIFICATIONS

1. DRAWINGS ARE DIAGRAMMATIC. COORDINATE AND DETERMINE FINAL LOCATIONS OF SYSTEMS ANDCOMPONENTS IN FIELD. COORDINATE WITH ARCHITECTURAL DRAWINGS AND OTHER TRADES.

2. THE INTENTION IS FOR INSTALLATION OF COMPLETE AND OPERATING SYSTEMS. NOT EVERYCOMPONENT REQUIRED IS SHOWN. THE CONTRACTOR SHALL INCLUDE ALL COMPONENTS NORMALLYASSOCIATED WITH THE PARTICULAR SYSTEM. THE SYSTEM SHALL BE FULLY COMMISSIONED ANDSIGNED OFF BY AN OFFICER OF THE RESPECTIVE CONTRACTOR PRIOR TO FINAL OWNER ACCEPTANCETESTING. PROVIDE PERSONNEL TO ASSIST WITH OWNER ACCEPTANCE TESTING.

3. GIVE NOTICES, FILE PLANS, OBTAIN PERMITS AND LICENSES, PAY FEES AND BACK CHARGES, ANDOBTAIN NECESSARY APPROVALS FROM AUTHORITIES THAT HAVE JURISDICTION AS REQUIRED TOPERFORM WORK IN ACCORDANCE WITH ALL LEGAL REQUIREMENTS AND WITH THE DESIGN DOCUMENTS.

4. MATERIALS AND EQUIPMENT SHALL BE LISTED BY UNDERWRITERS LABORATORIES (UL) AND APPROVEDBY ASME AND AGA, AS APPLICABLE, FOR INTENDED SERVICE.

5. THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS,TECHNIQUES, SEQUENCES AND PROCEDURES REQUIRED FOR SAFE EXECUTION AND COMPLETION OFTHE WORK AND FOR INITIATING, MAINTAINING AND SUPERVISING ALL SAFETY PRECAUTIONS ANDPROGRAMS IN CONNECTION WITH THE WORK.

6. ALL MATERIALS, EQUIPMENT AND METHOD OF INSTALLATION SHALL BE ACCORDANCE WITH THESTANDARDS, REGULATIONS, CODES, ORDINANCES AND LAW OF LOCAL, STATE AND FEDERALGOVERNMENTS AND OTHER AUTHORITIES THAT HAVE LAWFUL JURISDICTION.

7. IT SHALL BE THE RESPONSIBILITY OF THIS CONTRACTOR TO COORDINATE THE WORK UNDER THISCONTRACT WITH THAT OF ALL OTHER TRADES, INCLUDING, BUT NOT LIMITED TO, ELECTRICAL, HVAC,SPRINKLER, PLUMBING, STRUCTURAL AND GENERAL CONSTRUCTION. OFFSETS IN DUCTWORK,PIPINGAND CONDUITS AROUND OBSTRUCTIONS SHALL BE PROVIDED AT NO ADDITIONAL COST TO THEOWNER.

8. EACH CONTRACTOR IS RESPONSIBLE FOR CUTTING AND PATCHING REQUIRED FOR THE INSTALLATION OFNEW WORK UNDER THIS CONTRACT. CUTTING AND PATCHING SHALL BE COMPLETED IN A NEAT ANDWORKMANLIKE MANNER. PATCHING MATERIALS SHALL MATCH EXISTING MATERIALS TO THE GREATESTEXTENT POSSIBLE. PROVIDE TOUCH-UP TO MATCH EXISTING SURROUNDING AREAS OF CUTTING ANDPATCHING WORK.

9. INTERRUPTIONS TO EXISTING SERVICES AND SYSTEMS SHALL BE AS SHORT AS POSSIBLE AND AT ATIME AND DURATION APPROVED BY THE OWNER. INCLUDE ALL PREMIUM TIME ASSOCIATED WITHINTERRUPTIONS IN BID PROPOSAL. INTERRUPTIONS SHALL BE SCHEDULED WITH OWNER AT LEAST 48HOURS IN ADVANCE.

10. CONTRACTOR SHALL COORDINATE ITS RESPECTIVE CEILING MOUNTED EQUIPMENT AND DEVICES WITHOTHER TRADE CONTRACTORS PRIOR TO INSTALLATION TO AVOID CONFLICTS.

11. ALL DEBRIS SHALL BE CLEANED AND REMOVED FROM THE SITE BY END OF EACH WORK DAY. PRIOR TODISPOSAL OF EQUIPMENT AND MATERIALS, TURN OVER TO THE OWNER ANY REMOVED EQUIPMENT ANDMATERIALS REQUESTED BY THE OWNER.

12. WORK SHALL BE EXECUTED IN A WORKMANLIKE MANNER AND SHALL PRESENT A NEAT, RECTILINEARAPPEARANCE WHEN COMPLETED.

13. MAINTAIN MAXIMUM HEAD ROOM AT ALL TIMES. DO NOT RUN PIPES, DUCTS AND CONDUIT EXPOSEDUNLESS SHOWN AND NOTED TO BE EXPOSED ON DRAWINGS.

14. MATERIALS AND EQUIPMENT SHALL BE NEW, UNLESS NOTED OTHERWISE, AND INSTALLED ACCORDINGTO MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS SO THAT COMPLETED INSTALLATIONSHALL OPERATE SAFELY AND EFFICIENTLY.

15. EACH RESPECTIVE CONTRACTOR SHALL FIRE STOP ALL NEW AND EXISTING OPENINGS THROUGH FIRERATED FLOORS, WALLS AND CEILINGS WITH UL ASSEMBLIES OF EQUAL RATING. FIELD VERIFY EXISTINGCONDITIONS BEFORE SUBMITTING BID PROPOSAL.

16. COORDINATE ALL ROOF PENETRATIONS WITH WORK OF OTHER TRADES. ALL PENETRATIONS SHALL BESEALED WATERTIGHT. COORDINATE FLASHING REQUIREMENTS TO MAINTAIN ROOF WARRANTY.

17. MANUFACTURERS' MODEL NUMBERS ARE SPECIFIED SOLELY TO ESTABLISH STANDARDS OF QUALITYFOR PERFORMANCE AND MATERIALS.

18. SUBSTITUTED PRODUCTS SUBMITTED AND APPROVED FOR USE THAT NECESSITATE CHANGES TO THEWORK OF OTHER TRADES OF CONTRACT SHALL BE COORDINATED AND ARRANGED BY THE CONTRACTORWHO SUBMITTED THE SUBSTITUTION WITHOUT ADDITIONAL COST TO THE OWNER.

19. PRODUCT INSTALLATION SHALL ADHERE TO MANUFACTURER'S RECOMMENDATIONS AND INSTRUCTION.20. EACH RESPECTIVE CONTRACTOR SHALL PROVIDE PROPER ACCESS TO EQUIPMENT AND COMPONENTS

THAT REQUIRE INSPECTION, MAINTENANCE AND POSSIBLE REPAIR. ACCESS PANELS SHALL BE MINIMUM12"X12" OR AS NEEDED FOR PROPER ACCESS. ACCESS PANELS SHALL BE FURNISHED BY THISCONTRACTOR AND TURNED OVER TO GENERAL CONTRACTOR FOR INSTALLATION.

21. CONTRACTOR SHALL COORDINATE ELECTRICAL CHARACTERISTICS AND REQUIREMENTS OF ALLAPPLICABLE EQUIPMENT WITH THE ELECTRICAL CONTRACTOR.

22. AS WORK PROGRESSES AND FOR DURATION OF CONSTRUCTION, MAINTAIN A COMPLETE SET OFCONTRACT DRAWINGS AT THE JOBSITE. RECORD WORK COMPLETED AND ALL CHANGES FROM ORIGINALCONTRACT DRAWINGS CLEARLY AND ACCURATELY INCLUDING WORK INSTALLED AS A MODIFICATIONOR ADDITION TO THE ORIGINAL DESIGN TURN OVER ALL OPERATING MANUALS, MAINTENANCEMANUALS, AND "AS BUILT" DRAWINGS TO OWNER AT CONCLUSION OF CONSTRUCTION.

23. DO NOT SUPPORT EQUIPMENT, DUCTWORK, PIPING, CONDUIT OR DEVICES FROM SUSPENDED CEILINGS.SUPPORT ALL EQUIPMENT, DUCTWORK, PIPING, CONDUIT AND DEVICES FROM BUILDING STRUCTURE TOPROVIDE A VIBRATION FREE INSTALLATION. NOTIFY ARCHITECT AND STRUCTURAL ENGINEER OF ALLWEIGHTS AND METHODS OF SUPPORT.

24. ANY REFERENCE TO MECHANICAL, PLUMBING, FIRE PROTECTION OR ELECTRICAL CONTRACTORS NOTEDON THE DRAWINGS SHALL NOT BE INTERPRETED AS AN INTENTION TO DEFINE SEPARATE CONTRACTORSFOR THE RESPECTIVE WORK. THE GENERAL CONTRACTOR SHALL COORDINATE AND PROVIDE ACOMPLETE INSTALLATION WITH COMPLETE MECHANICAL, PLUMBING, FIRE PROTECTION ANDELECTRICAL SYSTEMS, REGARDLESS OF ANY REFERENCES TO OTHER TRADE CONTRACTORS.

25. GUARANTEE WORK OF THIS CONTRACTOR IN WRITING FOR A PERIOD OF ONE YEAR FROM THE DATE OFOWNER'S ACCEPTANCE OR CERTIFICATE OF SUBSTANTIAL COMPLETION. PROMPTLY REPAIR OR REPLACEDEFECTIVE MATERIALS, EQUIPMENT, WORKMANSHIP AND INSTALLATIONS THAT DEVELOP DEFECTSWITHIN THIS PERIOD. PROMPTLY AND TO OWNERS SATISFACTION, CORRECT DAMAGE CAUSED INMAKING NECESSARY REPAIRS AND REPLACEMENTS UNDER THIS GUARANTEE AT NO ADDITIONAL COSTTO OWNER. SUBMIT GUARANTEE TO ARCHITECT BEFORE FINAL PAYMENT IS MADE. STATEMENT OFGUARANTEE REQUIREMENTS SHALL NOT BE INTERRUPTED TO LIMIT OWNER'S RIGHTS UNDER LAW ANDTHIS CONTRACT.

MECHANICAL DUCTWORK/EQUIPMENT NOTES

REGULATION OF VOLUME DAMPER SHALL BE ACCESSIBLETHROUGH THE FACE OF DIFFUSER.

COIL WITH FLANGED CONNECTION ALL AROUND.

FD MOUNTING TYPE DEPENDS ON AIR VELOCITIES AND DUCTSIZE - SEE SPECIFICATIONS.

HEATINGCOIL

DIRECTIONOF FLOW

REMOVE

NEW WORK

EXISTING

ACCESS DOOR IN DUCT

X DIMENSIONS SHALL BE 4" (10 CM) MINIMUM. IF A OR B IS GREATERTHAN 24" X 6" MINIMUM VOLUME DAMPER SHALL BE IN SHORTERBRANCH.

CONNECTION TO LINEAR DIFFUSER PLENUM

FIRERATEDWALL

FD

HEATING COIL

FIRERATEDWALL

FIRE DAMPER

PLENUMOVERLINEARDIFFUSER

ACCESS DOOR IN DUCT

CONICAL FITTING

PLENUM OVER DIFFUSER

OFFSET IN HORIZONTAL PLANE SHALL BEMADE WITH SMOOTH FITTINGS.

SUPPLY

HORIZONTAL OFFSET

RISE OR DROP

TRANSITION

TAP TAKE-OFF

ELEVATION - OFFSET IS VERTICAL PLANESHALL BE MADE WITH SMOOTHFITTINGS.

MAXIMUM INCLUDED ANGLE OF TRANSITION SIDES IS 15 o

ALL TERMINALDEVICES

DAMPERVOLUME

ALL TERMINALDEVICES

RETURN

VOLUME DAMPER

DUCTWORK SYMBOLOGY

SPLIT OR TAKE-0FF

SINGLE THICKNESS TURNING VANES - IN SQUARE ELBOWS,RADIUS ELBOWS PREFERED - SUBJECT TO SPACE CONDITIONS.

SINGLE LINE

ELBOW

DAMPERVOLUME

B

CONSTANT VOLUMESYSTEM

A

XTO VAVTERMINALUNIT

VARIABLE VOLUMESYSTEM

ACTUAL CONSTRUCTION

FLEX DUCT

FLEX DUCT

HANDDAMPER

FLEX DUCT

HANDDAMPER

SF-- SUPPLY FAN

EF-- EXHAUST FAN

FAN COIL UNIT

UNIT HEATER

--

--UH

FC

CO2 CARBON DIOXIDE SENSOR

SMOKE DETECTOR ON AC UNITS

MOTION SENSOR

DIFFERENTIAL PRESSURE SENSOR

SD

MS

DP

LOUVERED DOOR

AIR FLOW

EXHAUST FAN

SUPPLY AIR FLOW

RETURN OR EXHAUST

NEW CONNECTION TO EXISTING

TEMINATION OF DEMOLITION

LVDR

T OR THERMOSTAT

VARIABLE SPEED

AIR HANDLING UNITAHU--

FAN SWITCH

PUMP--P

S

CALL OUT SYMBOLS

TEMPERATURE SENSOR

REVISION NUMBER/INDICATESA REVISED FEATURE1

FD SELF-CLOSING FIRE DAMPERW/ ACCESS DOOR

SUPPLY DIFFUSER

SUPPLY DIFFUSER

SMOKE DAMPER WITH ACCESS DOOR

BLANKED FOR 3-WAY BLOW

BLANKED FOR 2-WAY BLOW

1-WAY BLOW SUPPLY DIFFUSER

UNDERCUT DOORUC 1"

OR

SD

MOTOR OPERATED DAMPER/ ZONE DAMPER

HVAC LEGEND

HAND DAMPER

MOD/ZD

HD

VARIABLE FREQUENCY DRIVE

WET BULB TEMPERATURE

WELD-WIRE MESH SCREEN (1/4")

W

CHILLED WATER SUPPLY

CHILLED WATER RETURN

DRY BULB TEMPERATURE

DIRECT DIGITAL CONTROL

DIRECT EXPANSION

CUBIC FEET PER MINUTE

ENTERING AIR TEMPERATURE

EXHAUST GRILLE

EXHAUST REGISTER

EXTERNAL STATIC PRESSURE

ENTERING WATER TEMPERATURE

FIRE DAMPER (W/ ACCESS DOOR)

FEET PER MINUTE

DX

EXHAUSTEXH

FURN

FLRDR

FPM

FT

FURNISHED

FLOOR DRAIN

FEET

FA

FD

FLEX

EXP

(F)

FREE AREA

FLEXIBLE

EXPANSION

FUTURE

EFFICIENCYEFF

ER

ESP

EWT

EG

ELEC ELECTRICAL

EA

EAT

DL

(E)

EACH

DOOR LOUVER

EXISTING

DN

DIA

DIM

DIFF

DOWN

DIAMETER

DIMENSION

DIFFUSER

DDC

CHWR

DB

COLUMN

CHWS

CW

CONN

CONTR

COLD WATER

CONNECTION

CONTRACTOR

CO

COL

CLG

CL

CFM

CLEAN-OUT

CEILING

CENTERLINE

POUNDS PER SQ INCH GAUGE

REVOLUTIONS PER MINUTE

SOUND ATTENUATOR

RELATIVE HUMIDITY

POUNDS PER SQ INCH ABSOLUTE

SA

SPECIFICATIONSSPECS

SCHEDULE

SMOKE DAMPER

SQUARE FOOT

SCREEN

SD

SF

SCH

SCR

RET RETURN

REQUIRED

ROOM

RELOCATE(RL)

RM

RPM

REQ'D

RH

PLUMBING

REMOVE

REGISTER

(R)

REG

PLBG

PSIA

PSIG

LEAVING AIR TEMPERATURE

LOW PRESSURE COND. RETURN

LOW PRESSURE STEAM

LEAVING WATER TEMPERATURE

MOTOR OPERATED DAMPER

NORMALLY CLOSED

MOUNTED

NTS NOT TO SCALE

OUTSIDE DIAMETER

PRESSURE DROP

OUTSIDE AIR

PD

OD

OA

NOT APPLICABLE

NUMBER

NOT IN CONTRACT

MANUAL AIR VENT

NC

NO

NIC

MTD

N/A

MAV

MECHANICAL

MANUFACTURER

MINIMUM

MF'R

MIN

MOD

LWT

MECH

KILOWATT

INCHES

LPS

LPR

KW

LAT

IN

Ø DIAMETER

WATER GAUGE

WITHOUT

WITH

WWMS

W/O

WB

WG

W/

AIR CONDITIONING

AUTOMATIC CONTROL VALVE

ABOVE FINISHED FLOOR

AIR HANDLING UNIT

BRAKE HORSEPOWER

BOTTOM OF DUCT

BOTTOM OF PIPE

CEILING DIFFUSER

BHP

CD

BOD

BOP

ARCH

AP

AFF

AHU

ARCHITECT

ACCESS PANEL

ADD'L

AD

ACV

AC

ADDITIONAL

ACCESS DOOR

GENERAL ABBREVIATIONS

GENERAL CONTRACTOR

GALLONS PER MINUTE

HOSE BIBB CONN W/ CHAINED CAP

HOT WATER SUPPLY

HOT WATER RETURN

HOUR

HERTZ

HORSEPOWER

HWS

HZ

HWR

HR

HP

GRILLE

RETURN GRILLE

HAND DAMPER

HEIGHT

HD

HGT

GR

HB

GR

GAUGE

GALLONS

GALVANIZEDGALV

GC

GPM

GA

GAL

VENT

UNDERCUT DOOR

WIDTH

VOLUME DAMPER

TYPICAL

VD

VFD

V

TYP

UC

TRANSFER GRILLE

TRANSFER

TEMPERATURE

SUPPLY

TG

TR

TEMP

SUP

SUPPLY REGISTER

STEEL

STEAM

STEAM TRAP

SR

ST

STL

STM

MAXIMUMMAX

AC-- AIR CONDITIONING UNIT

CH-- CHILLER UNIT

BUTTERFLY VALVE

BALL VALVE

B-- BOILER

HEAT PUMP LOOP RETURN

HEAT PUMP LOOP SUPPLY

HPR

HPS

CONDENSER WATER SUPPLY

CONDENSER WATER RETURNCWR

CWS

THERMOMETER

P PRESSURE GAUGE

FMFLOW METER

FSD COMBINATION FIRE SMOKE DAMPER

CONDENSING UNITCU--

HEAT PUMPHP--

ELECTRIC HEATEREH--

CO CARBON MONOXIDE SENSOR

COMBINATION FIRE/SMOKE DAMPERFSD

RETURN GRILLERG

SF-- SUPPLY FAN

AVGT

OR THERMOSTATAVERAGING TEMPERATURE SENSOR

1. PROJECT CONDITIONS1.1. THE CONTRACTOR SHALL BECOME COMPLETELY FAMILIAR WITH ALL EXISTING BUILDING AND SITE

CONDITIONS AND LIMITATIONS WHICH MAY HAVE A BEARING ON THE OPERATIONS HEREIN SPECIFIEDAND SHALL INCLUDE ALL WORK REQUIRED TO COMPLETE THE PROJECT AS SHOWN ON THE DRAWINGS.NO EXTRA COMPENSATION WILL BE ALLOWED FOR UNFORESEEN CONDITIONS THAT CAN BEDETERMINED FROM A CAREFUL EXAMINATION OF THE SITE, BUILDING AND DRAWINGS.

1.2. ITEMS OF VALUE WHICH ARE NOT INDICATED TO BE RETURNED TO THE OWNER SHALL BECOME THEPROPERTY OF THE CONTRACTOR. STORAGE OR SALE OF ITEMS ON THE PROJECT SITE IS PROHIBITED.

1.3. PROTECTION: ENSURE THE SAFE PASSAGE OF PERSONS IN AND AROUND THE BUILDING DURINGDEMOLITION. PREVENT INJURY TO PERSONS AND DAMAGE TO PROPERTY. PROVIDE ADEQUATESHORING AND BRACING TO PREVENT COLLAPSE. IMMEDIATELY REPAIR DAMAGED PROPERTY TO THECONDITION BEFORE BEING DAMAGED. TAKE EFFECTIVE MEASURES TO PREVENT WINDBLOWN DUST.

1.4. UTILITIES: MAINTAIN ALL UTILITIES EXCEPT THOSE THAT REQUIRE REMOVAL OR RELOCATION. KEEPUTILITIES IN SERVICE AND PROTECT FROM DAMAGE. DO NOT INTERRUPT UTILITIES SERVING OCCUPIEDAREAS OF THE SITE OR BUILDING WITHOUT FIRST OBTAINING PERMISSION FROM OWNER.

2. REGULATION REQUIREMENTS2.1. STRICTLY COMPLY WITH APPLICABLE CODES, REGULATIONS AND REQUIREMENTS OR AUTHORITY

HAVING JURISDICTION.3. HANDLING OF MATERIALS

3.1. REMOVE DEBRIS FROM THE SITE AS IT ACCUMULATES. DO NOT STORE, SELL, BURN OR OTHERWISEDISPOSE OF DEBRIS ON SITE. REMOVE ALL MATERIAL IN SUCH MANNER AS TO PREVENT SPILLAGE.

4. TRANSFER OF RESPONSIBILITY AND DISPOSITION OF MATERIALS4.1. UPON RECEIPT OF NOTICE TO PROCEED WITH THE WORK, THE TITLE TO ALL MATERIALS FOR

DEMOLITION SHALL BE VESTED. THE CONTRACTOR WHEREUPON THE OWNER WILL NOT BERESPONSIBLE FOR THE CONDITION, LOSS OR DAMAGE TO SAID PROPERTY. ALL SUCH ITEMS SHALL BEREMOVED FROM THE OWNER'S PROPERTY.

5. DISPOSAL OF DEMOLISHED MATERIALS5.1. REMOVE UNUSED EQUIPMENT AND FIXTURES AND ALL ASSOCIATED DUCTWORK AND PIPING SERVICING

EQUIPMENT AND FIXTURES INCLUDING ANY ABANDONED DUCTWORK AND PIPING NOT ASSOCIATEDWITH SAID EQUIPMENT AND FIXTURES AND NOT REQUIRED FOR NEW WORK. REMOVE DUCTWORK ANDPIPING BACK TO THE NEXT LIVE BRANCH WHICH WILL NOT OBSTRUCT THE NEW WORK AND CAP AIR ORWATER TIGHT. TRANSPORT AND LEGALLY DISPOSE OF MATERIALS OFF SITE.

5.2. ALL DEMOLITION SHALL BE COORDINATED WITH OWNER, ARCHITECT, ENGINEER AND GENERALCONTRACTOR. ALL DEBRIS SHALL BE CLEANED UP AND REMOVED FROM THE SITE BY THE END OF EACHWORK DAY. PRIOR TO DISPOSAL OF EQUIPMENT AND MATERIALS, TURN OVER TO OWNER ANYREMOVED EQUIPMENT AND MATERIALS PER OWNER'S REQUEST.

6. CLEAN UP AND REPAIR6.1. UPON COMPLETION OF DEMOLITION WORK, REMOVAL TOOLS, EQUIPMENT AND DEMOLISHED

MATERIALS FROM SITE. REMOVE PROTECTION AND LEAVE INTERIOR AREAS BROOM CLEAN.6.2. REPAIR DEMOLITION PERFORMED IN EXCESS OF THAT REQUIRED. RETURN STRUCTURES AND

SURFACES TO REMAIN IN CONDITION EXISTING PRIOR TO COMMENCEMENT OF SELECTIVE DEMOLITIONWORK. REPAIR ADJACENT CONSTRUCTION OR SURFACES SOILED OR DAMAGED BY SELECTIVEDEMOLITION WORK.

DEMOLITION NOTES:

M-2 MECHANICAL DETAILS

P-1 PLUMBING NOTES, LEGEND, AND SCHEDULES

P-1.1 PLUMBING FLOOR PLAN - PHASE 1

PLUMBING FLOOR PLAN - PHASE 3

HVAC GENERAL NOTES:

1. THERMOSTATS SHALL BE HONEYWELL COMMERCIAL VISION PRO 8000 OR OWNER APPROVED, 7-DAYPROGRAMMABLE WITH OVER-RIDE BUTTON FOR OCCUPANT AFTER HOURS CONTROL AND PASSWORDPROTECTION. INSTALL THERMOSTATS 48" ABOVE FINISHED FLOOR OR AS DIRECTED OTHERWISE BY ARCHITECT.COORDINATE FINAL LOCATION FOR EACH THERMOSTAT WITH ARCHITECT IN FIELD.

2. ALL CONDENSATE DRAIN LINES SHALL BE PIPED FULL SIZE OF UNIT DRAIN OUTLET AND PROVIDED WITH 'P' TRAP.TERMINATE CONDENSATE DRAIN PIPING AT NEAREST DRAIN.

3. EACH ROOFTOP UNIT OVER 2000 CFM SHALL HAVE A DUCT SMOKE DETECTOR LOCATED IN THE RETURN AIRSTREAM. DUCT SMOKE DETECTOR SHALL DE-ENERGIZE RESPECTIVE UNIT UPON ACTIVATION. DUCT SMOKEDETECTOR SHALL BE PROVIDED AND INSTALLED BY HE MECHANICAL CONTRACTOR. DUCT SMOKE DETECTORSHALL BE WIRED TO THE FIRE ALARM SYSTEM BY THE ELECTRICAL CONTRACTOR UNDER THE MECHANICALCONTRACTOR'S SCOPE OF WORK. MECHANICAL CONTRACTOR SHALL COORDINATE ALL WORK WITH THEELECTRICAL CONTRACTOR.

4. ALL CONTROL AND INTERLOCK WIRING FOR HVAC EQUIPMENT, WHETHER IT BE LINE OR LOW VOLTAGE, SHALL BETHE RESPONSIBILITY OF THE MECHANICAL CONTRACTOR.

5. ALL CONTROL WIRE AND CONDUIT SHALL COMPLY WITH NEC.6. EACH SYSTEM, EACH PIECE OF EQUIPMENT AND EACH AIR DEVICE SHALL BE FULLY TESTED AND BALANCED

UPON COMPLETION OF THE INSTALLATION WORK.7. TESTING AND BALANCING SHALL BE PROVIDED BY A COMPANY SPECIALIZING IN THE TESTING AND BALANCING OF

HVAC SYSTEMS. THE TEST AND BALANCE COMPANY SHALL BE A MEMBER OF AABC OR NEBB. BALANCEAIRFLOWS WITHIN 10% OF SCHEDULED AIR FLOWS TO ALL AIR DEVICES. IF AIR FLOW CANNOT BE BALANCED TOWITHIN 10%, PERFORM UP TO TWO PITOT TUBE TRAVERSES, AS DIRECTED BY OWNERS' REPRESENTATIVE, TODETERMINE THE CAUSE OF THE DEFICIENCY. SUBMIT SIX COPIES OF THE BALANCING REPORT FOR REVIEW PRIORTO FINAL INSPECTIONS.

8. DESIGN CONDITIONS ARE AS FOLLOWS:OUTDOOR SUMMER: 91 DEG DB, 75 DEG WB (ASHRAE 1%)INDOOR SUMMER: 74 DEG DB, 55% RHOUTDOOR WINTER: 11.6 DEG DB (ASHRAE 99.6%)INDOOR WINTER: 70 DEB DB

1. ALL DUCTWORK SHALL BE IN ACCORDANCE WITH SMACNA (SHEET METAL AND AIR CONDITIONING CONTRACTORSNATIONAL ASSOCIATION) STANDARDS.

2. PRIOR TO COMMENCING WORK, SHEET METAL SHOP DRAWINGS MUST BE PREPARED AND SUBMITTED FOR REVIEWAND APPROVAL TO THE ARCHITECT/ENGINEER. SHEETMETAL SHOP DRAWINGS SHALL INCLUDE ALL ELEMENTS OFTHE EQUIPMENT, DUCTWORK, AIR DEVICES, AND REFLECTED CEILING PLAN FOR COORDINATION OF CRITICALDIMENSIONS OF ARCHITECTURAL/ STRUCTURAL COMPONENTS.

3. SHEET-METAL FITTINGS SHOWN ARE TO BE PROVIDED. NO SUBSTITUTIONS ALLOWED WITHOUT PRIOR CONSENTFROM ENGINEER AND WILL BE REQUIRED TO BE REPLACED IF INSTALLED.

4. ALL WORK SHALL BE COORDINATED WITH ALL TRADES INVOLVED. OFFSETS IN PIPING AND DUCTS (INCLUDINGDIVIDED DUCTS) AND TRANSITIONS AROUND OBSTRUCTIONS SHALL BE PROVIDED AT NO ADDITIONAL COST TO THEOWNER.

5. VERIFY ALL EQUIPMENT CONNECTIONS WITH MANUFACTURER'S CERTIFIED DRAWINGS. VERIFY AND PROVIDE DUCTTRANSITIONS TO EQUIPMENT. FIELD VERIFY AND COORDINATE ALL DIMENSIONS BEFORE FABRICATING.

6. SUPPORT ALL EQUIPMENT AND DUCTWORK FROM BUILDING STRUCTURE TO PROVIDE A VIBRATION FREEINSTALLATION. NOTIFY STRUCTURAL ENGINEER OF ALL WEIGHTS AND METHODS OF SUPPORT.

7. REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR EXACT LOCATIONS OF AIR TERMINAL DEVICES.8. PROVIDE FLEXIBLE CONNECTIONS ON ALL DUCTS CONNECTING TO AIR HANDLING UNITS AN FANS.9. THE INSIDE OF ALL UNLINED DUCTWORK VISIBLE THROUGH A GRILLE SHALL BE PAINTED FLAT BLACK.10. PROVIDE FIRE DAMPERS WHERE SHOWN ON DRAWINGS AND/OR WHERE REQUIRED BY NFPA (NATIONAL FIRE

PROTECTION ASSOCIATION) 90A. FOR DUCTS THAT PENETRATE FIRE WALLS, FLOORS AND PARTITIONS, PROVIDESLEEVES WHERE PENETRATIONS ARE NOT PERPENDICULAR TO SURFACE PENETRATION. ENCLOSE DAMPERS IN 10GAUGE STEEL SLEEVE.

11. INSULATE ALL SUPPLY AIR AND RETURN AIR DUCTWORK WITH R-6 (INSTALLED) FIBROUS GLASS DUCT-WRAP WITHFOIL-DRAFT FLAME RESISTANT VAPOR BARRIER. INSULATION SHALL BE FIRE RATED IN ACCORDANCE WITH ASHRAE(AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR CONDITIONING ENGINEERS) 90A, 50/25 SMOKEDEVELOPMENT AND FLAME SPREAD REQUIREMENTS.

12. FLEXIBLE DUCT LENGTH SHALL NOT EXCEED 10 FEET. FLEXIBLE DUCT SHALL BE FABRIC COVERED GALVANIZEDSTEEL HELIX MECHANICALLY LOCKED TO THE FABRIC. THE FABRIC SHALL BE A LAMINATE OF ALUMINUM FOILFIBERGLASS AND ALUMINIZED POLYESTER WITH VAPOR BARRIER JACKET RATED AT 5500 RPM WITH FLEX-MASTERUSA TYPE 3 OR EQUAL. INSULATION R-VALUE SHALL MATCH SPECIFIED R-VALUE FOR AIR SYSTEM SERVED.

13. THOROUGHLY CLEAN ALL NEW DUCTWORK AFTER INSTALLATION.14. VOLUME DAMPERS SHALL BE PROVIDED AT THE BRANCH TAKE-OFF OF THE MAIN AND FOR EACH AIR DEVICE.15. DUCTWORK SCHEDULE

A. MEDIUM PRESSURE - SUPPLY DUCTWORK FROM AIR HANDLING UNIT TO VAV BOX SHALL BE 4-INCH W.G.CONSTRUCTION, LEAKAGE CLASS A, SEAL CLASS 12. MATERIAL SHALL BE GALVANIZED STEEL UNLESS NOTEDOTHERWISE.

B. LOW PRESSURE - ALL OTHER SUPPLY AIR, RETURN AIR AND EXHAUST AIR DUCTWORK SHALL BE 2-INCH W.G.CONSTRUCTION, LEAKAGE CLASS B, SEAL CLASS 12. MATERIAL SHALL BE GALVANIZED STEEL UNLESS NOTEDOTHERWISE.

ELECTRICAL COVER SHEET

ELECTRICAL DETAILS

E-1

E-2

ELECTRICAL FLOOR PLAN - LIGHTING - PHASE 1

ELECTRICAL FLOOR PLAN - LIGHTING - PHASE 2

ELECTRICAL FLOOR PLAN - POWER - PHASE 1

E-1.1

E-1.2

E-2.1

M-3 MECHANICAL SCHEDULES

FP-1.1 FIRE PROTECTION FLOOR PLAN - PHASE 1

FIRE PROTECTION FLOOR PLAN - PHASE 2FP-1.2

FP-1 FIRE PROTECTION LEGEND, GENERAL NOTES AND DETAILS

PD-1 PLUMBING DEMOLITION FLOOR PLAN

FIRE PROTECTION FLOOR PLAN - PHASE 3FP-1.3

M-1.2 MECHANICAL FLOOR PLAN - PHASE 2

M-1.3 MECHANICAL FLOOR PLAN - PHASE 3

ELECTRICAL FLOOR PLAN - POWER - PHASE 2E-2.2

ELECTRICAL FLOOR PLAN - LIGHTING - PHASE 3E-2.3

AS

N

OT

ED

AC

DF

T

T

T STT

RTU7

1

2

1

13

EXISTING LOCKED BOX WHICHCONTAINS CONTROL STATS FORRTU UNITS, RTU- 4,5,6 & 7.

(E) 34X14

(E) 14X5

(E) 1

2X6

(R) 8"Ø (R) 8"Ø

(R) 8"Ø(R) 8"Ø

(E) 1

4X5

(E) 1

4X8

(E) 1

2X10

(E)12X12RR

(E)12X12RR

(E)12X12CD

(E)12X12CD

(E)12X12CD

(E)12X12CD

AHU-5

13

(R) 8"Ø

RTU5

13

(E)12X12CD

(E)12X12CD

(E)12X12CD

(E)12X12CD

(E)8X4

(E)8X6

S

(E) 26X10

(E) 2

8X12

(E) 2

0X12

(R) 8"Ø (R) 8"Ø

(R) 8"Ø (R) 8"Ø

(E) 24X10 (R) 10"Ø

(R)VAV-STAT

S

T

(R) 5"Ø

(R)15X7(LINED)

T(R)VAV-STAT

VAV5

(R)VAV-STAT

OFF TOP OFDUCT- 8"Ø

(E) 16X6

(E) 20X8(E) 16X6

(E) 3

0X8

(E) 1

2X8

(E) 1

2X6

(E) 8

X4(E

) 8X4

(E) 10X4

(E) 10X4(E) 10X4

(E) 1

0X10

(E) 8X4

RTU8

3

(E)12X12RR

(E) 56X12

(E) 60X14

(E) 5

6X12

(E) 20X12

DSD

(E) 38X16

DSD

(E) 6

"Ø

(E) 1

0X5

(E) 1

2X6

(E) 10X5

(E) 3

0X12

(E) 3

0X8

(E) 2

6X8

(E) 12X5

(E) 15X6

(E) 8X4

VAV5(E)12X12

(LINED)

(R) 5"Ø

(E) 1

8X12

(E) 1

8X12

(E) 16X10

(E) 18X12(E) 15X6

(E) 10"Ø(R)12X12CD

(E) 1

4X8

(LIN

ED)

(E) 8"Ø

(E) 1

4X10

(LIN

ED)

(E) 8"Ø

(E) 8"Ø

(E) 1

8X10

(LIN

ED)

(E) 22X10(LINED)

VAV5

(R) 10"Ø(E) 30X12

(E) 1

8X12

(E) 3

4X14

(E) 22X14(LINED)(R) 10"Ø

(R) 8"Ø

(E) 1

0X8(E) 2

0X10

(E) 8

X4

(R) 8"Ø

(E) 8X4

(E) 28X10

(E) 2

4X10

(E) 4

4X10

(E) 2

2X10

VAV5

(E) 12X6

(E) 20X8

(E) 2

0X8

(E) 10X10

EFM-1

(R)

6

(E) 1

0X10

(E) 16X5

(E) 1

6X5

(E) 14X6

(E) 8

X4

(E) 1

6X8

(E) 8X4 (E) 14X6 (E) 14X5

(E) 14X5

(E) 2

4X14

(E) 10X4

(E) 1

8X6

(E) 20X8

(E) 18X6

(E)18X9(LINED)

(R) 10"Ø

VV5

(R) 10"Ø

(R) 10"Ø

(E)18X10

(R) 10"Ø

(E)16X8(LINED)

VV5

VV5

(E) 2

4X14

(R)VAV-STAT

(R)VAV-STAT

(R)VAV-STAT &TEMP. DIAL

(R) 10"Ø

(E)16X8(LINED)

(E)20X12

(E) 14X5

(E) 2

0X12

(R) 10"Ø

(E) 1

6X6

(LIN

ED)

VV5

(E) 15X6

(E) 15X6

(E) 8"Ø

(R) 8"Ø

(R) 8"Ø

(E) 2

0X12

(LIN

ED)

8

(E) 8X4

(E) 10X8

(E) 8X6

7

7(R)VAV-STAT

S

7

T

(R)VAV-STAT

RTU6

13

RTU4

13

RTU3

3

RTU2

3

RTU1

3

T

T

T

T

T

T

(E) 16X5(E) 16X8(E) 10X6

(E) 10X6

(E) 1

0X4

(E) 1

0X4

(E) 12X6

VAV5

VAV5 (R) CD

(R) CD

(E) 1

4X5

(R) RR

(R)VAV-STAT

(R) RR

(R) CD

(E) 1

6X8

(R) 5"Ø

(R) 5

"Ø

(E) 20X7

(E) 18X10

(E) 1

2X6

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) RR

VAV5

(R) 7

"Ø

(E) 16X10(E) 16X10

(E) 1

0X8 (R) CD

(R) CD

(R) CD

VAV5

(R) 10"Ø

(E) 1

6X8

(E) 14X4

(R)VAV-STAT

(E) 18X16

(E) 2

4X16

(R) RR

(E) 14X4(E) 14X6

(E) 14X4

(E) 1

4X6

(E) 14X8

(E) 14X4

(R)12X12RR

(R)VAV-STAT

(E) 1

4X10

(R) 10"Ø

(E) 2

4X12

(E) 14X6(R) RR

(E) 18X10

(E) 8X4

(E) 8X6

(R) RR(R) RR

(R) CD

(E) 16X6

(E) 22X6

(E) 16X10

(E) 14X6

(E) 10X4

(E) 2

2X10

(E) 2

8X10

(E) 2

0X8

(E) 2

2X8(E) 8X4

(E) 1

0X4 (R) CD

(R) CD(E) 8X4

(E)8

X4

(E) 8

X6

(R) RR

(E) 2

8X16

(E) 3

2X16

(E) 1

6X6

(R) RR

(R) RR

(E) 8X4

(E) 14X6

(E) 14X6

VAV5

(R) 10"Ø

(R)VAV-STAT

(R)VAV-STAT

(R) CD

(R) CD

(E) 1

6X10

(E) 3

0X12

(E) 3

2X16

(E) 12X4

(E) 8

X4

(R) RR

(E) 1

2X4

(R) CD

(E) 18X6 (E) 12X6(E) 12X4

(E) 1

6X10

(E) 1

6X10

(E) 1

8X12

(E) 14X8(R) CD

(E) 8

X4

(R) CD

(R) CD

(E) 14X6

(E) 12X4

(R) CD

(E) 40X16(E) 40X16

(E) 3

0X12

(E) 2

0X8

(E) 40X16

(E) 40X16

(E) 3

2X16

(E) 2

0X14

(E) 2

0X14

(E) 40X16

VAV5

VAV5

VAV5

(R) 5"Ø

(R) 10"Ø

(E) 10X4

(R) CD

(R) RR

(R) CD

(E) 12X6

(E) 3

0X12

(R)VAV-STAT

(R) CD

(R) RR

(R) 10"Ø

(E) 1

6X10

(E) 1

4X8

(E) 14X8

(E) 2

0X12

(R) CD (R) CD

(R) RR

(R) RR

EFP-1

(R)

(R) RR

(R) CD

(E) 8

X4

(R) RR(E) 8X4

10

11

12

(R) ER

(E) 1

6X16

(R) CD

(E) 22X16

(E)16X8

(R) CD

(E) 8X4

(E) 1

8X12

(E) 2

0X16

(E)1

6X10

(R) RR

(R) RR

(R) CD (R) CD

(E) 14X5

(E)14X5

(E)16X10

(E)12X4(E)12X4

(E)12X4 (E)12X4

(E)16X8

(E)1

4X6

(E)4

0X16

(E)1

0X6

(E) 22X16(E) 22X16

(R) CD

(E)10X10(E)14X8

(E) 1

2X4

(E) 1

4X6

(E)2

6X12

(E)30X16(E)16X8

(E)12X10

(E)10X4

(E)10X10

(E)10X4

(E) 1

6X12

(R) ER

(R) ER

(R) CD

(R) CD (R) RR

(R) CD

(E)16X8

DSD 8

DSD 8

(E)10X6

(E)1

8X12

(E) 10X8

(E) 8

X4

(R) RR

(R) RR

(R) CD

(R) CD

(R) RR

(E) 1

4X6

(E) 1

6X6

(E) 1

6X6

(E) 2

0X10

(E) 10X4

(R) CD

(E) 10X4

(E)1

0X6

(E) 10X4(R) CD

14

EH-

(E)

EH-

(E)

EFM-2

(R)

T (R)VAV-STAT

S

(R) CD(R) RR

(R) RR

(R)VAV-STATT

S

7

(R) CD

S

7

(R) RR

(R) CD

(R) RR

(R) RR

1

1

1

(R) CD14

14

EXISTING LOCKED BOX WHICHCONTAINS CONTROL STATS FORRTU UNITS, RTU- 1,2 & 3.REMOVE RTU-1 & 3 STATS &RTU-2 STAT IF ADD-ALT ISACCEPTED.

(E) HOOD

(R) CD

(R) ER

(R) RR

(R) RR

T

(R)VAV-STAT

(E) 10X4(R) CD

(R) RR

(R) RR

(R) CD

(R) CD

(R) RR

(R) ER-SIDEWALL

(R) ER

(R) CD

(R) CD

(R) CD(R) CD

T(R)RTU-3

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD (R) CD

(R) CD (R) CD

(R) CD

(R) CD(R) CD

(R) CD

(R) CD (R) CD

(R) CD(R) CD

(R) CD (R) CD

(R) CD

(R) CD(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) ER(R) CD

(R) CD

(E) 8X4

(R) CD

(R) RR

(R) RR

(R) RR

(R) RR(R) RR

(R) ER

(R) RR

(R) RR

(R) RR

(R) RR

(R) RR

(R) RR(R) RR(R) RR

(R) RR

(R) RR

(R) ER

(R) ER

(R) RR

(R) CD

(R) CD

(R) CD (R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD

(R) CD(R) CD

(R) CD

(R) CD

SAHU-4

13(R) RR

(R) RR

(R) CD

(R) CD(R) CD

(R) CD

(R) RR (R) RR

T (E) EH STAT

EH-

(E)

(R) RR

(R) RR

EH-

(E)

(R) CD (R) CD (R) CD (R) CD

(R) CD

(R) RR

(R) SR HIGHIN SLOPEDCLG.

T(E) EH STAT

ON ROOF

EFP-2

(R)

15

15

15

16

MOD/ZD

T

4

VAV

CONFERENCE RM.

TO HAVE A COMPLETE RTU & ASSOCIATED VAV BOXES ANDCONTROLS REMOVE NOTED VAV BOXES AND ASSOCIATEDCONTROLS IN AREAS NOT IN SCOPE

LOCK-UP AREALOCK-UP AREA

(R) RR

VAV

(E)1

0X4LD-1

4'-0" L, 4- SLOT, 1" SLOT285 CFM

EH-

(E)

VAV

LOCK-UP AREA

EXTERIOR OFFICE

(E)14X6

5

5

5

(ADD -ALT)

(R) TEMPERATURE SENSOR &ASSOCIATED CONTROL WIRING BACKTO THERMOSTAT LOCATIONS . SEETHIS DRAWING.

MECHANICAL NOTES:

EXISTING HIGH WALL HEAT PUMP UNIT , ASSOCIATED PIPING ,CONTROLS AND ROOFTOP CONDENSING UNIT TO REMAIN.

EXISTING 2 1 /2 TON ROOFTOP CONDENSING UNIT SERVING HIGHWALL INDOOR HEAT PUMPS TO REMAIN.

REMOVE EXISTING RTU (ON ROOF) AND ASSOCIATED CONTROLS.REPLACEMENT RTU SHALL HAVE ROOF CURB ADAPTER, SEESCHEDULE AND CONSTRUCTION PLANS.

REMOVE EXISTING RTU SENSOR.

REMOVE EXISTING VAV BOX AND ASSOCIATED CONTROL STAT.

EXISTING 12X12 EXHAUST DUCT UP TO EXHAUST GOOSENECK ONROOF.

EXISTING TO REMAIN TEMPERATURE SENSOR AND ASSOCIATEDCONTROL WIRING TO RTU CONTROL STATS. IF ADD-ALT TO REPLACERTU-2 IS ACCEPTED, REMOVE TEMPERATURE SENSORS & ALLASSOCIATED WIRING ETC BACK TO THE RTU THERMOSTATSLOCATION IN THE POLICE SIDE OF BUILDING.

REMOVE EXISTING SMOKE DETECTOR FROM SUPPLY DUCTWORK.PATCH AIRTIGHT.

REMOVE EXISTING ROOFTOP EXHAUST FAN AND ROOF CURB.

(E) EXHAUST DUCT DN TO HOOD.

(E) EXHAUST DUCT UP TO WEATHER CAP ON ROOF.

(E)16X16 EXHAUST DUCT UP TO WEATHER CAP ON ROOF.

EXISTING RTU AND ASSOCIATED CONTROLS TO REMAIN.

CAP DUCT AIR TIGHT SEAL

ADD-ALT -REMOVE EXISTING EXHAUST FAN, HANGERS ETC.EXISTING CONTROL DEVICE TO REMAIN FOR CONNECTION TO NEWFAN.

ADD-ALT-REMOVE EXISTING ROOFTOP EXHAUST FAN. REMOVE ROOFCURB IF NEW FAN CANNOT BE INSTALLED ON CURB OR WITH ANADAPTER CURB.

1

2

3

4

5

7

8

6

9

10

11

12

13

14

GENERAL MECHANICAL DEMOLITION NOTES:

1. PRIOR TO COMMENCEMENT OF DEMOLITION, CONTRACTOR SHALLMEASURE AIRFLOW AT EACH HVAC UNIT AND AIR DEVICE AND PROVIDEA REPORT OF THE FINDINGS TO OWNER, ARCHITECT AND ENGINEERFOR REVIEW.

2. INTENT IS TO DISCONNECT AND REMOVE ALL EXISTING AIR DEVICESAND ANY ASSOCIATED FLEX DUCTWORK BACK TO THE NEAREST SHEETMETAL MAIN. PATCH AIRTIGHT SEAL OR CONNECTION FOR NEWDUCTWORK. REFER TO NEW WORK PLANS FOR NEW WORK.

15

16

KEY PLAN

PHASE 1 PHASE 2

MD-1

1

SCALE - 1/8" = 1'-0"

MECHANICAL DEMOLITION FLOOR PLAN

AS

N

OT

ED

JM

F

DF

N

0' 4' 16'8'

BRANCH/ FLEX DUCT SIZING SCHEDULE

DUCT SIZE CFM RANGE REMARK

6"Ø

8"Ø

10"Ø

12"Ø

0-100

101-260

261-400

401-600

MAX 10' LENGTH. FLEX DUCTWORK APPROVED ON SUPPLY SYSTEMSONLY.RETURN AND EXHAUST TO BE HARD DUCTED.

RTU6

RTU4RTU

3

RTU2

RTU1

(E) 16X5(E) 16X8

(E) 12X6

(E) 1

4X5

(E) 1

6X8

6"Ø

8"Ø

(E) 20X7

(E) 18X10

(E) 1

2X6

12X12 RR245 CFM 6

"Ø

(E) 16X10(E) 16X10

(E) 1

0X8

8"Ø

(E) 1

6X8

(E) 14X4(E) 18X16

(E) 2

4X16

(E) 14X4

(E) 14X6

(E) 1

4X6

(E) 14X8

(E) 14X4

(E) 1

4X10

10"Ø

(E) 2

4X12

(E) 14X6

(E) 18X10

(E) 8X4

(E) 8X6

(E)22X6

(E) 2

8X10

(E) 2

0X8

(E) 2

2X8

(E) 1

0X4

(E) 8X4

(E)8

X4

(E) 8

X6

(E) 28X16

(E) 3

2X16

(E) 1

6X6

(E) 8X4

12"Ø

(E) 1

6X10

(E) 3

0X12

(E) 3

2X16

(E) 12X4

(E) 8

X4

(E) 1

2X4

(E) 18X6 (E) 12X6(E) 12X4

(E) 1

6X10

(E) 1

6X10

(E) 1

8X12

(E) 14X8

(E) 8

X4

(E) 14X6

(E) 12X4

(E) 40X16(E) 40X16

(E) 3

0X12

(E) 2

0X8

(E) 40X16

(E) 40X16

(E) 3

2X16

(E) 20X14

(E) 2

0X14

(E) 40X16

VAVF

4"Ø

8"Ø

(E) 10X4

(E) 12X6

(E) 3

0X12

(E) 1

2X6

12"Ø

(E) 1

6X10

(E) 1

4X8

(E) 14X8

(E) 2

0X12

EFP-1

(ON ROOF)

(E) 8

X4

(E) 8X4

(E) 1

6X16

(E) 22X16

(E)16X8

(E) 8X4

(E) 1

8X12

(E) 2

0X16

(E)1

6X10

(E) 14X5

(E)14X5

(E)16X10

(E)12X4(E)12X4

(E)12X4 (E)12X4

(E)16X8

(E)1

4X6

(E)4

0X16

(E)1

0X6

(E) 22X16(E) 22X16

(E)14X8

(E) 1

2X4

(E) 1

4X6

(E)2

6X12

(E)30X16(E)16X8

(E)12X10 (E)10X10

(E)10X4

(E) 1

6X12

(E)16X8

DSD

DSD

(E)10X6

(E)1

8X12

(E) 10X8

(E) 8

X4

12X12 RR380 CFM

(E) 1

4X6

(E) 1

6X6

(E) 1

6X6

(E) 2

0X10

(E) 10X4

(E) 10X4

(E)1

0X6

VVD

VVC

VVC

VVE

VVF

VVA

VVD

T

TVV-C

T VV-C

T

VV-D

T

VV-E

TVV-F

T

VV-D

VVD

5

5

8

66

6

10

11

11

24X24 CD150 CFM

24X24 CD340 CFM

12X12 RRXXCFM

12X12 RR300 CFM12X12 RR

175 CFM

12X12 RR270 CFM

12X12 RR270 CFM

12X12 RR175 CFM

8X8 RR110CFM

24X24 RR490 CFM

12X12 CD100 CFM

12X12 RR100 CFM

TVV-A

12X12 RR170 CFM

12X12 RR160 CFM

TVV-F

6X6 CD80 CFM

6"Ø

14X14 RR370CFM

12X12 RR285 CFM

9X9 CD145 CFM

8X12 RR145 CFM

VAVA

12X12 CD120 CFM

(E)1

0X4

12X12 RR115 CFM

12X12 ER150 CFM

6X6 CD80 CFM

6X6 CD80 CFM

6X6 CD120 CFM

12X12 ER340 CFM

24X24 CD90 CFM

12X12 RR170 CFM

12X12 CD155 CFM

6X6 RR110 CFM

6X6 RR50 CFM

12X12 RR120 CFM

6X6 CD75 CFM

12X12 CD130 CFM

12X12 CD120 CFM

6X6 CD110 CFM

12X12 RR220 CFM

6X6 CD75 CFM

6X6 CD140 CFM

6X6 RR75CFM

6X6 RR140 CFM

12X12 CD95 CFM

12X12 RR95 CFM

6X6 CD120 CFM

6X6 CD55 CFM

12X12 CD190 CFM

6X6 RR55 CFM

12X12 ER340 CFM

12X12 ER335 CFM

6X6 CD110 CFM

6X6 CD110 CFM

12X12 CD170 CFM

12X12 CD170 CFM

6X6 CD150 CFM

(E)12X8

(E)14X4

(E)14X10

(E)14X10

12X12 RR250 CFM

12X12 RR345 CFM

12X12 RR345 CFM

(E)8X4

(E)1

0X6(E

)14X

10

(E)1

0X4 (E)30X20

12X12 CD130 CFM

12X12 CD280 CFM

12X12 CD280 CFM

6X6 CD100 CFM

12X12 CD190 CFM

12X12 CD190 CFM

12X12 CD190 CFM

12X12 CD190 CFM

12X12 RR380 CFM12X12 RR

380 CFM

LD-14'-0" L, 4- SLOT, 1" SLOT245 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 3 /4" SLOT 150 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 1 /2"SLOT110CFM

LD-14'-0" L, 2- SLOT,3 /4" SLOT 150 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT170 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT160 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT185 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT185 CFM

LD-14'-0" L, 4- SLOT, 1" SLOT285 CFM

EH-

(E)

EH-

(E)

12

12

EFM-2

7

EFP-2

7

300

200

245

350

540

1090

735

330

130

750

230

VAVE

VAVC

LOCK-UP AREA

100

EXTERIOR OFFICE

CONFERENCE RM.

VV-D

24X24 RR490 CFM

24X24 CD190 CFM

24X24 CD190 CFM

8"Ø

8"Ø

8"Ø

8"Ø

8"Ø

14X8

16X6

14X6

TO HAVE A COMPLETE RTU & ASSOCIATED VAV BOXES ANDCONTROLS PROVIDE NOTED VAV BOXES IN AREAS NOT IN SCOPE .PROVIDE ALL NECESSARY DUCTWORK ETC TO INSTALL BOXES INEXISTING DUCTWORK. ALSO PROVIDE THERMOSTATS FOR VAVCONTROL TO RTU.

8"Ø

4"Ø

8"Ø

8"Ø

SRTU-3SENSOR

(E) 1

4X6

(E)10X4

6X6 ER75 CFM

6X6 CD80 CFM

6X6 ER60 CFM

12X12 ER125 CFM

6X6 CD45 CFM

12X12 RR170 CFM

(E) 8X4

6X6 CD105 CFM

MOD/ZD

(E) CONTROLS TO REMAIN. BALANCE AIRFLOW WITHHOOD OPERATION

8X4

12X12 CD155 CFM

12X12 ER400 CFM

24X24 CD90 CFM

6X6 CD75 CFM

6X6 RR50 CFM

6X6 RR50 CFM

(E) 2

2X8(E) 8X4

(R) CD

(E) 10X4

(E) 10X4

12X12 CD190 CFM

12X12 RR120 CFM

6X6 RR60 CFM

S

RTU-2 SENSORADD-ALT

EXISTING LOCKED BOX WHICHCONTAINS CONTROL STATS FORRTU UNITS, RTU- 1,2 & 3.

14

ADD-ALT100 CFM

ADD-ALT100 CFM

ADD-ALT110 CFM

ADD-ALT110 CFM

ADD-ALT130 CFM

ADD-ALT130 CFM

ADD-ALT75 CFM

ADD-ALT75 CFM

ADD-ALT45 CFM

ADD-ALT45 CFM

ADD-ALT160 CFM

ADD-ALT160 CFM

ADD-ALT320 CFM

ADD-ALT100 CFM

ADD-ALT100 CFM

ADD-ALT120 CFM

ADD-ALT120 CFM

ADD-ALT100 CFM

ADD-ALT125 CFM

ADD-ALT70 CFM

ADD-ALT210 CFM

ADD-ALT70 CFM

ADD-ALT30 CFM

ADD-ALT70 CFM

(E)CD & RR120 CFMADD-ALT100 CFM

(E)12X12 RR180 CFMADD-ALT150 CFM

(E)12X12 CD180 CFMADD-ALT150 CFM

ADD-ALT50 CFM

ADD-ALT100 CFM

ADD-ALT80 CFM

ADD-ALT80 CFM

ADD-ALT65 CFM

ADD-ALT65 CFM

ADD-ALT120 CFM

ADD-ALT120 CFM

ADD-ALT180 CFM

ADD-ALT90 CFM

(E) HIGH WALL AC UNITS (TYP OF 3)

(ADD-ALT)

6X6 CD105 CFM

TRTU-4

S

S

1 (TYP)

14

15

(TYP)

1 (TYP)

3(TYP)

GENERAL MECHANICAL CONSTRUCTION NOTES

1. INTEGRAL OPPOSED BLADE DAMPERS SHALL BE PROVIDEDAT ALL AIR DEVICES. FINAL SUPPLY AIR DEVICE BALANCINGSHALL BE PERFORMED VIA INTEGRAL AIR DEVICE

2. ALL PENETRATIONS THRU RATED ASSEMBLIES SHALL BEPROVIDED WITH RADIANT DAMPERS.

3. FLEX DUCT WORK LENGTHS SHALL BE LIMITED TO WHAT ISALL INDICATED ON M-100.

4. ALL DIFFUSERS AND REGISTERS LOCATED IN TOILET ROOMSSHALL BE ALUMINUM CONSTRUCTION.

5. ALL RETURN/EXHAUST REGISTERS SHALL HAVE 45˚ FIXEDBLADES.

6. ALL SUPPLY MAINS SHALL BE LINED WITH 1" INTERNAL LINING. ALL BRANCH DUCTWORK SHALL BE EXTERNALLYWRAPPED.

7. REFER TO RTU DETAIL FOR INSTALLATION REQUIREMENTS.

8. ALL DUCT SIZES ARE INSIDE DUCT DIMENSIONS.9. REFER TO ARCHITECTURAL PLANS FOR FINAL AIR DEVICE

LOCATIONS.10. CONNECT NEW AIR DEVICES TO EXISTING DUCTWORK WITH

FLEX DUCTWORK OR SHEET METAL DUCTWORK AS REQUIRED.

SPECIAL MECHANICAL CONSTRUCTION NOTES

1. ADDITIONAL DUCTWORK IS SHOWN TO ACCOMMODATE NEWROOMS OR CHANGES TO THE AREA USAGE. THIS IS BECAUSE OFEXISTING DUCTWORK FROM THE ASSOCIATED RTU IS NOT PRESENTOR INADEQUATE SIZE. ROUTE NEW DUCTWORK AS REQUIRED,PROVIDE ALL OFFSETS, FITTINGS ETC FOR A COMPLETEINSTALLATION.2. PROVIDE ALL NECESSARY FLEX DUCT, DUCTWORK, FITTINGSETC. FOR CONNECTIONS FROM NEW AIR DEVICES TO EXISTINGDUCTWORK

MECHANICAL NOTES (ALL PHASES):

CAP DUCT AIR TIGHT SEAL.

DUCTWORK FROM RTU-5 TO REMAIN. BALANCE AIRDEVICES TO CFM INDICATED.

CONNECT AS REQUIRED WITH 'HARD DUCT' THE RETURNREGISTER TO EXISTING RETURN MAIN.

CONNECT MAIN LOBBY AIR DEVICES IN NEW CEILINGGRID TO EXISTING DUCTWORK AS REQUIRED.

EXISTING RTU TO REMAIN.

NEW RTU- SEE SCHEDULE.

NEW INLINE EXHAUST FAN, SEE SCHEDULE FOR FURTHERINFORMATION. ADD-ALT

NEW ROOFTOP EXHAUST FAN, SEE SCHEDULE FORFURTHER INFORMATION. ADD-ALT

EXISTING EXHAUST DUCT UP TO GOOSENECK ON ROOF.

EXISTING EXHAUST DUCT DN TO HOOD.

EXISTING EXHAUST DUCT UP TO ROOFTOP WEATHER CAP

INSTALL DUCT MOUNTED SMOKE DETECTOR IN RETURNDUCT MAIN.

BALANCE AIR DEVICE TO EXISTING AIRFLOW.

TYPICAL FOR ALL CONNECTIONS BETWEEN NEW ANDEXISTING WORK.

CONNECT NEW FLEX DUCTWORK SERVING VAV BOXES TOEXISTING DUCTWORK AS REQUIRED. (TYP)

15

14

13

12

2

1

3

4

5

6

7

8

9

10

11

RTU-2 ADD ALT NOTES:1.ADD - ALT IS FOR RTU-2 (17.5 TONS) TO BE REPLACED.PER EXISTING DRAWINGS THE TOTAL AIRFLOW OF THE UNIT IS 4955CFM. THE CFM NOTED FOR AIR DEVICES SERVED BY RTU-2 ARE FORTHE EXISTING UNIT NOT BEING REPLACED AND AN ADD- ALT CFM ISFOR THE UNIT BEING REPLACED.2. IF ADD-ALT IS ACCEPTED REMOVE TEMPERATURE SENSORS ANDALL ASSOCIATED WIRING ETC BACK TO THERMOSTATS LOCATION INTHE POLICE SIDE OF BUILDING.

KEY PLAN

PHASE 1

M-1-1

1

SCALE - 1/8" = 1'-0"

MECHANICAL FLOOR PLAN - PHASE 1

AS

N

OT

ED

JM

F

DF

N

0' 4' 16'8'

Project:

Description: Date: Scale:

Sketch #

.\AEI Title Block.jpg

BRANCH/ FLEX DUCT SIZING SCHEDULE

DUCT SIZE CFM RANGE REMARK

6"Ø

8"Ø

10"Ø

12"Ø

0-100

101-260

261-400

401-600

MAX 10' LENGTH. FLEX DUCTWORK APPROVED ON SUPPLY SYSTEMSONLY.RETURN AND EXHAUST TO BE HARD DUCTED. T

EXISTING LOCKED BOX WHICHCONTAINS CONTROL STATS FORRTU UNITS, RTU- 4,5,6 & 7.

(E) 34X14

(E) 14X5

(E) 1

2X6

(E) 8"Ø (E) 8"Ø

(E) 8"Ø(E) 8"Ø

(E) 1

4X5

(E) 1

4X8

(E) 1

2X10

(E)12X12 RR340 CFM

(E)12X12 CD195 CFM

(E)12X12 CD195 CFM

22X22 RR1100 CFM

24X24 CD100 CFM

RTU5

(E)12X12 CD110 CFM

(E)8X4

(E)8X6

(E) 26X10

(E) 2

8X12

(E) 2

0X12

8"Ø 8"Ø

(E) 24X10

OFF TOP OFDUCT- 8"Ø

(E) 3

0X8

(E) 1

2X8

(E) 1

2X6

(E) 8

X4

(E) 10X4

24X24 CD60 CFM 24X24 CD

200 CFM

(E) 10X4(E) 10X4

16X16 RR560 CFM

(E) 1

0X10

(E) 8X4

RTU8

(E)12X12 RR440 CFM 12X12 CD

225 CFM

(E) 56X12

(E) 60X14

(E) 5

6X12

(E) 20X12

DSD

(E) 38X16

DSD

(E) 1

0X5

(E) 1

2X6

(E) 10X5

12X12 CD105 CFM

12X12 CD105 CFM

(E) 3

0X12

(E) 3

0X8

(E) 15X6

(E)12X12(LINED)

(E) 1

8X12

(E) 1

8X12

(E) 16X10

(E) 18X12(E) 15X6

(E) 1

8X10

(LIN

ED)

(E) 22X10(LINED)

(E) 30X12

(E) 1

8X12

(E) 3

4X14

(E) 22X14 (LINED)10"Ø

8X12 ER300 CFM

(E) 1

0X8(E) 2

0X10

(E) 8

X4

6"Ø

(E) 8X46X6 ER75 CFM

6X6 CD75 CFM

(E) 28X10

6X6 CD75 CFM

12X12 RR270 CFM(OFF BOTTOMOF RTN DUCT)

24X24 CD270 CFM

(E) 2

4X10

(E) 4

4X10

(E) 2

2X10

(E) 12X6

(E) 20X8

(E) 2

0X8

(E) 10X10

EFM-1

(E) 1

0X10

(E) 16X5

(E) 1

6X5

(E) 14X6

(E) 8

X4

6X6 CD40 CFM

(E) 1

6X8

(E) 2

4X14

8"Ø 18X18

RR410 CFM

12X12RR270 CFM

(E) 1

8X6

(E) 20X8

(E) 18X6

(E)18X9(LINED)

VVE

(E)18X10

6"Ø

VVC

(E) 2

4X14

(E)20X12

30X8

(E) 2

0X12

(E) 15X6

(E) 2

0X12

(LIN

ED)

(E) 8X4

(E) 10X8

(E) 8X6

18X18RR400 CFM

22X22RR900 CFM

(E)12X12 CD110 CFM

(E)12X12 CD110 CFM

(E)12X12 CD110 CFM

(E)12X12 CD190 CFM

(E)12X12 CD190 CFM

(E)12X12 RR340 CFM

CO2

CO2

T

VVD

TVV-E VV-C VV-D

T VV-F

T VV-E

12X12RR130 CFM

12X12RR160 CFM

12X12RR

VVF

VVE

22X22RR800 CFM

VVE

TVV-E

12X12RR-1200 CFM

VVD

TVV-D

12X12RR-300 CFM

22X22RR1125 CFM

VVF

TVV-F

BUILDING FACILITY AREA HVAC TO REMAINAS-IS.RE-BALANCE AIR DEVICES TO CFMINDICATED.

12X12 CD140 CFM

12X12 CD140 CFM

12X12 CD140 CFM

12X12 CD140 CFM

12X12 RR210 CFM

22X22RR260 CFM

8"Ø

8"Ø

8X12 ER300 CFM

12X12 CD225 CFM

12X12 CD100 CFM

24X24 CD130 CFM

(E) 56X12

12X8

12X8

24X24 CD210 CFM

24X24 CD100 CFM

22X22RR865 CFM

12X12 RR290 CFM 14X6

24X24 CD145 CFM

24X24 CD145 CFM

24X24 CD400CFM

24X24 CD300 CFM

24X24 CD350 CFM

24X24 CD350 CFM

(E) 1

6X8

16x14

16X1

2

14X1

0

7

2

3

1

3

3

5

9

6

LD-14'-0" L, 2- SLOT, 1" SLOT180 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT220 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT180 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT180 CFM

LD-14'-0" L, 2- SLOT, 3/4" SLOT150 CFM

24X24 CD185 CFM

24X24 CD180 CFM

LD-14'-0" L, 2- SLOT, 3/4" SLOT150 CFM

LD-14'-0" L, 2- SLOT, 1 /2" SLOT100 CFM

LD-14'-0" L, 2- SLOT, 1/2" SLOT100 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT220 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT180 CFM

LD-14'-0" L, 2- SLOT,1" SLOT180 CFM

LD-14'-0" L, 2- SLOT, 3 /4" SLOT125 CFM

LD-14'-0" L, 2- SLOT, 3 /4" SLOT160 CFM

LD-14'-0" L, 2- SLOT, 3 /4" SLOT130 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT220 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT180 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT220 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT200 CFM

LD-14'-0" L, 2- SLOT, 3 /4" SLOT135 CFM

LD-14'-0" L, 2- SLOT,3 /4" SLOT135 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT210 CFM

LD-14'-0" L, 2- SLOT, 1" SLOT210 CFM

LD-14'-0" L, 1- SLOT, 3 /4" SLOT85 CFM

LD-14'-0" L, 1- SLOT, 3 /4" SLOT80CFM

RTU7

5

12

1

8"Ø 1125

8"Ø 8"Ø

8"Ø

300

615

24X24 CD220 CFM

800

12

10X8

8" Ø

7" Ø

900

400 270

585

24X24 CD280 CFM1

1

1

1

1

1

10"Ø

8"Ø

6"Ø

6"Ø

14

14

15

10X10

20X6

10"Ø

12X1

212

X14

1

24X8

12X14 12"Ø

14

10"Ø

1

1

1

1

14X6

14X6

14X628X8

12"Ø

8"Ø

14

8"Ø

6"Ø

8X10

14X6

AHU-5SENSOR

T

24X8

S

S

S

(E) SENSOR FOR RTU-7

(E) SENSOR FOR RTU-7

(TYP)

MECHANICAL NOTES (ALL PHASES):

CAP DUCT AIR TIGHT SEAL.

DUCTWORK FROM RTU-5 TO REMAIN. BALANCE AIRDEVICES TO CFM INDICATED.

CONNECT AS REQUIRED WITH 'HARD DUCT' THE RETURNREGISTER TO EXISTING RETURN MAIN.

CONNECT MAIN LOBBY AIR DEVICES IN NEW CEILINGGRID TO EXISTING DUCTWORK AS REQUIRED.

EXISTING RTU TO REMAIN.

NEW RTU- SEE SCHEDULE.

NEW INLINE EXHAUST FAN, SEE SCHEDULE FOR FURTHERINFORMATION. ADD-ALT

NEW ROOFTOP EXHAUST FAN, SEE SCHEDULE FORFURTHER INFORMATION. ADD-ALT

EXISTING EXHAUST DUCT UP TO GOOSENECK ON ROOF.

EXISTING EXHAUST DUCT DN TO HOOD.

EXISTING EXHAUST DUCT UP TO ROOFTOP WEATHER CAP

INSTALL DUCT MOUNTED SMOKE DETECTOR IN RETURNDUCT MAIN.

BALANCE AIR DEVICE TO EXISTING AIRFLOW.

TYPICAL FOR ALL CONNECTIONS BETWEEN NEW ANDEXISTING WORK.

CONNECT NEW FLEX DUCTWORK SERVING VAV BOXES TOEXISTING DUCTWORK AS REQUIRED. (TYP)

11

10

9

8

7

6

5

4

3

1

2

SPECIAL MECHANICAL CONSTRUCTION NOTES

1. ADDITIONAL DUCTWORK IS SHOWN TO ACCOMMODATE NEWROOMS OR CHANGES TO THE AREA USAGE. THIS IS BECAUSE OFEXISTING DUCTWORK FROM THE ASSOCIATED RTU IS NOT PRESENTOR INADEQUATE SIZE. ROUTE NEW DUCTWORK AS REQUIRED,PROVIDE ALL OFFSETS, FITTINGS ETC FOR A COMPLETEINSTALLATION.2. PROVIDE ALL NECESSARY FLEX DUCT, DUCTWORK, FITTINGSETC. FOR CONNECTIONS FROM NEW AIR DEVICES TO EXISTINGDUCTWORK

12

13

GENERAL MECHANICAL CONSTRUCTION NOTES

1. INTEGRAL OPPOSED BLADE DAMPERS SHALL BE PROVIDEDAT ALL AIR DEVICES. FINAL SUPPLY AIR DEVICE BALANCINGSHALL BE PERFORMED VIA INTEGRAL AIR DEVICE

2. ALL PENETRATIONS THRU RATED ASSEMBLIES SHALL BEPROVIDED WITH RADIANT DAMPERS.

3. FLEX DUCT WORK LENGTHS SHALL BE LIMITED TO WHAT ISALL INDICATED ON M-100.

4. ALL DIFFUSERS AND REGISTERS LOCATED IN TOILET ROOMSSHALL BE ALUMINUM CONSTRUCTION.

5. ALL RETURN/EXHAUST REGISTERS SHALL HAVE 45˚ FIXEDBLADES.

6. ALL SUPPLY MAINS SHALL BE LINED WITH 1" INTERNAL LINING. ALL BRANCH DUCTWORK SHALL BE EXTERNALLYWRAPPED.

7. REFER TO RTU DETAIL FOR INSTALLATION REQUIREMENTS.

8. ALL DUCT SIZES ARE INSIDE DUCT DIMENSIONS.9. REFER TO ARCHITECTURAL PLANS FOR FINAL AIR DEVICE

LOCATIONS.10. CONNECT NEW AIR DEVICES TO EXISTING DUCTWORK WITH

FLEX DUCTWORK OR SHEET METAL DUCTWORK AS REQUIRED.

14

15

KEY PLAN

PHASE 2

M-1.2

1

SCALE - 1/8" = 1'-0"

MECHANICAL FLOOR PLAN - PHASE 2

AS

N

OT

ED

JM

F

DF

N

0' 4' 16'8'

BRANCH/ FLEX DUCT SIZING SCHEDULE

DUCT SIZE CFM RANGE REMARK

6"Ø

8"Ø

10"Ø

12"Ø

0-100

101-260

261-400

401-600

MAX 10' LENGTH. FLEX DUCTWORK APPROVED ON SUPPLY SYSTEMSONLY.RETURN AND EXHAUST TO BE HARD DUCTED.

12X12 CD450 CFM

12X12 CD450 CFM

12X12CD450 CFM

6X6 CD110 CFM

(E) 16X6

(E) 22X6

(E) 16X10

(E) 14X6

(E) 10X4

(E)22X6

(E) 2

2X10

24X24 RR730 CFM

(E) 2

0X8

(E) 2

2X8

4

44

4

4

(E) 26X10

24X24 RR1300 CFM

(E) 16X6

(E) 20X8(E) 16X6

12X12 CD440 CFM

12X12 CD420 CFM

12X12 CD440 CFM

4

4

4

4

T (E) EH STAT

EH-

(E)EH-

(E)

PROVIDE SR HIGHIN SLOPEDCLG.

T(E) EH STAT

12X12 RR

12X12 RR

13

13

24X24 RR730 CFM

4

ADD-ALT100 CFM

ADD-ALT550 CFM

ADD-ALT240 CFM

ADD-ALT380 CFM

ADD-ALT380 CFM

ADD-ALT550 CFM

SPECIAL MECHANICAL CONSTRUCTION NOTES

1. ADDITIONAL DUCTWORK IS SHOWN TO ACCOMMODATE NEWROOMS OR CHANGES TO THE AREA USAGE. THIS IS BECAUSE OFEXISTING DUCTWORK FROM THE ASSOCIATED RTU IS NOT PRESENTOR INADEQUATE SIZE. ROUTE NEW DUCTWORK AS REQUIRED,PROVIDE ALL OFFSETS, FITTINGS ETC FOR A COMPLETEINSTALLATION.2. PROVIDE ALL NECESSARY FLEX DUCT, DUCTWORK, FITTINGSETC. FOR CONNECTIONS FROM NEW AIR DEVICES TO EXISTINGDUCTWORK

GENERAL MECHANICAL CONSTRUCTION NOTES

1. INTEGRAL OPPOSED BLADE DAMPERS SHALL BE PROVIDEDAT ALL AIR DEVICES. FINAL SUPPLY AIR DEVICE BALANCINGSHALL BE PERFORMED VIA INTEGRAL AIR DEVICE

2. ALL PENETRATIONS THRU RATED ASSEMBLIES SHALL BEPROVIDED WITH RADIANT DAMPERS.

3. FLEX DUCT WORK LENGTHS SHALL BE LIMITED TO WHAT ISALL INDICATED ON M-100.

4. ALL DIFFUSERS AND REGISTERS LOCATED IN TOILET ROOMSSHALL BE ALUMINUM CONSTRUCTION.

5. ALL RETURN/EXHAUST REGISTERS SHALL HAVE 45˚ FIXEDBLADES.

6. ALL SUPPLY MAINS SHALL BE LINED WITH 1" INTERNAL LINING. ALL BRANCH DUCTWORK SHALL BE EXTERNALLYWRAPPED.

7. REFER TO RTU DETAIL FOR INSTALLATION REQUIREMENTS.

8. ALL DUCT SIZES ARE INSIDE DUCT DIMENSIONS.9. REFER TO ARCHITECTURAL PLANS FOR FINAL AIR DEVICE

LOCATIONS.10. CONNECT NEW AIR DEVICES TO EXISTING DUCTWORK WITH

FLEX DUCTWORK OR SHEET METAL DUCTWORK AS REQUIRED.

MECHANICAL NOTES (ALL PHASES):

CAP DUCT AIR TIGHT SEAL.

DUCTWORK FROM RTU-5 TO REMAIN. BALANCE AIRDEVICES TO CFM INDICATED.

CONNECT AS REQUIRED WITH 'HARD DUCT' THE RETURNREGISTER TO EXISTING RETURN MAIN.

CONNECT MAIN LOBBY AIR DEVICES IN NEW CEILINGGRID TO EXISTING DUCTWORK AS REQUIRED.

EXISTING RTU TO REMAIN.

NEW RTU- SEE SCHEDULE.

NEW INLINE EXHAUST FAN, SEE SCHEDULE FOR FURTHERINFORMATION.

NEW ROOFTOP EXHAUST FAN, SEE SCHEDULE FORFURTHER INFORMATION.

EXISTING EXHAUST DUCT UP TO GOOSENECK ON ROOF.

EXISTING EXHAUST DUCT DN TO HOOD.

EXISTING EXHAUST DUCT UP TO ROOFTOP WEATHER CAP

INSTALL DUCT MOUNTED SMOKE DETECTOR IN RETURNDUCT MAIN.

BALANCE AIR DEVICE TO EXISTING AIRFLOW.

TYPICAL FOR ALL CONNECTIONS BETWEEN NEW ANDEXISTING WORK.

CONNECT NEW FLEX DUCTWORK SERVING VAV BOXES TOEXISTING DUCTWORK AS REQUIRED. (TYP)

11

10

9

8

7

6

5

4

3

1

2

12

13

14

15

NOTE:ADD - ALT IS FOR RTU-2 (17.5 TONS) TO BE REPLACED.PER EXISTING DRAWINGS THE TOTAL AIRFLOW OF THE UNIT IS 4955CFM. THE CFM NOTED FOR AIR DEVICES SERVED BY RTU-2 ARE FORTHE EXISTING UNIT NOT BEING REPLACED AND AN ADD- ALT CFM ISFOR THE UNIT BEING REPLACED.

KEY PLAN

PHASE 3M-1.3

1

SCALE - 1/8" = 1'-0"

MECHANICAL FLOOR PLAN - PHASE 3

AS

N

OT

ED

JM

F

DF

N

0' 4' 16'8'

CD

CEILING

TRAPROOF

FLASH WATERTIGHT

SUPPLY AIR

FLEXIBLECONNECTION (TYP.)

PROVIDE 45° TAPEREDCONNECTION AT RISER(TYP.)

FACTORY ROOF CURB

CONDENSATE DRAIN,DISCHARGE AT ROOF DRAIN

ACOUSTICALLY LINED DUCTWORKFIRST 10' OF SUPPLY AND RETURN,ALL OTHER DUCTWORK SHALL HAVEWRAP INSULATION

---RTU

RETURN AIR

M-2

1

SCALE: NONE

ROOFTOP UNIT DETAIL

PLUG

EXTEND AND SPILLTO ROOF DRAIN

TYPE "L" COPPEROR SCH 40 PVC

1 1/2" FOR DRAWTHRU UNITS

PLUG

M-2

2

SCALE: NONE

CONDENSATE TRAP DETAIL

ROOFTOPUNIT

MATERIAL:

S

SMOKE DETECTOR, UNITS OVER 2000 CFM, WIRED FORUNIT SHUTDOWN AND CONNECTED TO BLDG.FIRE ALARM SYSTEM AS REQUIRED

NEOPRENE GASKET

12" HIGH INSULATEDROOF CURB

ROOF

PENETRATION BOX

INSULATED REMOVABLECOVER

BASIS: PATE MODEL: CPBA-2 ORSHOP FABRIBATED

PROVIDE NEOPRENEPENETRATION SEAL AT ALLREFRIGERANT PIPES

3" Ø PVC FROM HOT WATER HEATER

2" RIGID FIBERGLASS INSULATIONINSTALL WITH WELDED PINS

BRAZED 90° ELBOW FITTING (TYPALL REFRIGERANT LINES)

SIDE VENT TERMINAL

SUPPLY AIR

MAIN DUCT

TAPERED CONNECTION 45º ANGLE(IF MAIN DUCT IS RECTANGULAR) ORCONICAL CONNECTION (IF MAIN DUCTIS ROUND) L = 1/4 W; 4" MIN

W

LBRANCH DUCT

(SEE PLANS FOR SIZE)UNLESS INDICATED OTHERWISEROUND DUCT TO DIFFUSER

VOLUME DAMPER

MAIN DUCT

FLEX DUCT10'-0" LONG

MAX

PLAN VIEW

ROOF DECK

CONDUIT FOR POWER TO FAN TOCLEAR DAMPER OPERATION

ROOFING OVER CURB BYROOFING CONTRACTOR

INSECT SCREEN

SECURE FAN BASE TO CURB

MOTOR

SETTING OF CURB BYMECH. CONTRACTOR

ANCHOR BACKDRAFTDAMPER TO ROOF DECK

GRAVITY BACKDRAFT DAMPER WITHADJUSTABLE COUNTER BALANCE

INSULATED ROOF CURB

M-2

5

SCALE: NONE

ROOF MOUNTED EXHAUST FAN DETAIL

M-2

6

SCALE: NONE

ROOF - PENETRATION BOX DETAIL

M-2

3

SCALE: NONE

FLEXIBLE DUCT DETAIL

M-2

4

SCALE: NONE

BRANCH TAKE-OFFS

ADD-ALT

AS

N

OT

ED

JM

F

DF

UNIT NO.

675

CFMMODELMFGR

ELECTRICALCHARACTERISTICS

STANDARD OFDESIGN

MUNICIPAL OFFICE BATHROOMS INLINE 0.5

ESP HP RPM WEIGHT

1

2

1

FLA

PROVIDE: SPEED CONTROLLER, GRAVITY BACKDRAFT DAMPER,DISCONNECT SWITCH,ROOF CURB AND OR ROOF CURB ADAPTER,BIRD SCREEN.

3 PROVIDE: SPEED CONTROLLER, DISCONNECT SWITCH, INTEGRALGRAVITY BACKDRAFT DAMPER, VIBRATION ISOLATION AND HANGERKIT.

GREENHECK

SONE

EF-M-1 120-V - 1Ø - 60 Hz

REMARKSTYPEAREA SERVED

EXHAUST FAN SCHEDULE

VERIFY THAT NEW EXHAUST FAN MATCHES EXISTING FAN TYPE, CFM, SP & VOLTAGE OF EXISTINGFAN. CONNECT NEW EXHAUST FAN INTO EXISTING CONTROL DEVICES.

SEQUENCE OF OPERATIONS:GENERAL1. UNIT SHALL HAVE A 7-DAY PROGRAMMABLE THERMOSTAT WITH THE FOLLOWING SCHEDULING MODES. a. OCCUPIED b. UNOCCUPIED2. IF ROOFTOP UNIT AIRFLOW IS 2000 CFM OR GREATER, A SMOKE DETECTOR SHALL BE PROVIDED IN THE AIRSTREAM AND INTEGRATED WITH THE FIRE ALARM SYSTEM TO DE-ENERGIZE THE FAN IN THE EVENT OF A FIRE ALARM EVENT.OCCUPIED MODE1. WHEN SYSTEM IS INDEXED TO THE OCCUPIED MODE THE FOLLOWING SHALL OCCUR. a. FAN TO BE INDEXED TO "ON" b. OUTSIDE AIR DAMPER TO BE OPENED TO THE MINIMUM POSITION. c. RETURN AIR DAMPER TO BE INDEXED TO THE APPROPRIATE POSITION RELATIVE TO THE OA DAMPER. (I.E. OA = 10%, RA = 90%) d. MODES OF OPERATION COOLING: WHEN SPACE TEMPERATURE RISES ABOVE THE THERMOSTATS COOLING SETPOINT AND THE OUTSIDE AIR ENTHALPY IS ABOVE THE ECONOMIZER

SETPOINT, THE FAN & 1ST STAGE OF REFRIGERATION CIRCUIT SHALL BE ENERGIZED TO PROVIDE COOLING TO THE SPACE. ON A CONTINUED RISE INSPACE TEMPERATURE, THE SECOND STAGE OF COOLING SHALL BE ENERGIZED (WHERE APPLICABLE). ON A DROP IN SPACE TEMPERATURE THEREVERSE SHALL OCCUR.

HEATING: WHEN SPACE TEMPERATURE DROPS BELOW THE THERMOSTATS HEATING SETPOINT THE FAN & 1ST STAGE OF HEATING CIRCUIT SHALL BEENERGIZED TO PROVIDE HEATING TO THE SPACE. ON A CONTINUED FALL IN SPACE TEMPERATURE THE SECOND STAGE OF HEATING SHALL BEENERGIZED (WHERE APPLICABLE). ON A RISE IN SPACE TEMPERATURE THE REVERSE SHALL OCCUR.

ECONOMIZING: WHEN SPACE TEMPERATURE RISES ABOVE THE THERMOSTAT'S COOLING SETPOINT AND THE OUTSIDE AIR ENTHALPY IS AT OR BELOW THEECONOMIZER SETPOINT, THE FAN SHALL ENERGIZE AND THE OUTSIDE AIR DAMPER AND RELIEF DAMPER SHALL MODULATE OPEN AND THERETURN AIR DAMPER SHALL MODULATE CLOSED TO MAINTAIN A 53°F MIXED AIR TEMPERATURE. THE POWERED EXHAUST FAN SHALL ENERGIZE TOMAINTAIN BUILDING PRESSURIZATION (WHERE APPLICABLE). IF MIXED AIR EXCEEDS SETPOINT AND THE SPACE TEMPERATURE CONTINUES TORISE, THE REFRIGERATION CIRCUIT SHALL BE ENERGIZED. ON A FALL IN SPACE TEMPERATURE THE REVERSE SHALL OCCUR.

UNOCCUPIED MODE1. WHEN THE SYSTEM IS INDEXED TO THE UNOCCUPIED MODE THE FOLLOWING SHALL OCCUR. a. FAN SHALL BE INDEXED TO "AUTO" b. OUTSIDE AIR DAMPER SHALL REMAIN CLOSED c. RETURN AIR DAMPER SHALL BE INDEXED TO THE OPEN POSITION (100%) d. THE HEATING & COOLING CIRCUITS SHALL CYCLE TO MAINTAIN SET BACK TEMPERATURES.

NO SCALE

PACKAGED ROOFTOP HEATING / COOLING

HONEYWELLCOMMERCIALTHERMOSTAT

ROOF TOP AIRCONDITIONING UNIT

S

INPUT

COOLING-DX

OUTPUT FILTER

INDIRECT FIRED GAS HEAT

SMBHTMBH

95 DEG OAT1

PACKAGED ROOFTOP AIR CONDITIONING UNIT SCHEDULE

REMARKSMOCP VOLT/PHASE/HZMCA

ELECTRICAL CHARACTERISTICSWEIGHT

LBS MODELMFGR.

STANDARD OF DESIGN

TRAN-EXSITING

NOMINALTONS

SUPPLYAIR CFM HP

ESP(IN. W.G.)

INDOOR SUPPLY FANOUTSIDEAIR CFM

TYPEUNIT NO.

TRANERTU-1 VAV UNIT W/ DX COOLING & GAS HEAT MERV 8

AIR DEVICE SCHEDULE

CD SUPPLY

SYMBOL TYPE MOUNTINGSERVICE ACCESSORIES REMARKSSIZE MATERIAL

STEEL

FINISH

WHITE

MAX.NC

25LOUVER

MODELMFGR.

STANDARD OF DESIGN

PRICEOBD

RR OBDWHITERETURN ALUMINUM 25RETURN REGISTER PRICEREFER TO PLAN

REFER TO PLAN

REFER TO PLAN

REFER TO PLAN

ER-1 OBDWHITEEXHAUST ALUMINUM 30EXHAUSTREGISTER

PRICEREFER TO PLAN REFER TO PLAN

LD-1 OBDWHITESUPPLY ALUMINUM 25 BORDER TYPE 15 FOR T-BAR CEILING INSTALLATION. LINEAR SLOT DIFFUSER

PRICEREFER TO PLAN REFER TO PLAN SDS

TRANERTU-2 MERV 8

RTU-5

RTU-6

RTU-7

TRANE- EXISTING

TRAN-EXISTING

AIRFLOWAPPLICATION

AIRFLOWRPM

EATDB/WB

UNIT LATDB/WB STAGES

EATF

LATF MBH MBH STAGES

EER/IEER (SEER)

2 PROVIDE ROOF CURB ADAPTERS FOR UNIT INSTALLATION, VARIABLE SPEED COMPRESSORS- MODULATING 25% - 100%, MODULATING GAS HEAT- 2.5:1 TURNDOWN, CFS FFS & COND DP OVERFLOW SWITCH, DEMAND CONTROL VENTILATION (CO2), CO2 DUCTMOUNTED ZONE SENSOR, POWER EXHAUST, BAYSENS119 PROGRAMMABLE ZONE TEMPERATURE SENSOR CONFIGURED AS A CONSTANT VOLUME UNIT, SINGLE ZONE VARIABLE AIR VOLUME CONTROL SEQUENCE OF OPERATION, THROUGH THE BASEELECTRICAL WITH DISCONNECT SWITCH,ECONOMIZER,REFERENCED OR COMPARATIVE ENTHALPY, MICROPROCESSOR CONTROLS, HUMIDITY DUCT MOUNTED SENSOR, DIRTY FILTER SWITCH, POWERED WEATHERPROOF GFI OUTLET, CONNECT CONDENSATEDRAIN TO EXISTING HORIZONTAL DRAIN ON ROOF, MC SHALL INSTALL SMOKE DETECTOR IN RETURN DUCT MAIN, DISCONNECT GAS LINES FROM UNITS BEING REMOVED AND RECONNECT GAS LINES TO NEW INSTALLED UNITS..

SPD

635

635

SQUARE TO ROUND ADAPTER AS REQUIRED.

3 /4" SPACING 45 ° DEFLECTION

3 /4" SPACING 45 ° DEFLECTION

TRANERTU-3 MERV 8

TRANE- EXSITINGRTU-4

UNIT NO. INLET

VAV BOX SCHEDULE

BOXTYPE

BASIS OF DESIGN

MFGR MODEL NO.REMARKS

VAV - A OPEN/SHUT

CFM RANGEM

OPEN/SHUT

OPEN/SHUT

OPEN/SHUT

OPEN/SHUT

WITH ECONOMIZER (RTU-3, 2-ADD-ALT)

SEQUENCE OF OPERATIONS:GENERAL1. A CHANGEOVER VAV SYSTEM RESPONDS TO THE CHANGING COOLING OR HEATING DEMANDS BY VARYING THE QUANTITY OR VOLUME OF AIR DELIVERED TO EACH ZONE.EACH ZONE HAS A TEMPERATURE SENSOR FOR INDIVIDUAL COMFORT CONTROL. THE RTU'S CONTROL SYSTEM DETERMINES ZONE HEATING OR COOLING NEEDS BY USINGVOTING LOGIC, THEN REQUESTS HEATING OR COOLING FROM THE RTU.2. THE ROOFTOP UNIT'S RETURN DUCT MOUNTED SMOKE DETECTOR SHALL BE INTEGRATED WITH THE FIRE ALARM SYSTEM TO DE-ENERGIZE THE FAN IN THE EVENT OF A FIRE ALARM EVENT.

VAV VOTING FOR SYSTEM HEAT OR COOL1. EACH ZONE ATTACHED TO THE RTU'S CONTROL SYSTEM CAN 'VOTE' FOR HEATING OR COOLING. EACH ZONE GETS ONE VOTE AND IS ELIGIBLE TO VOTE IF:

a. THE ZONE IS IN COMMUNICATION WITH THE RTU'S CONTROLS. b. THE ZONE HAS A VALID ZONE TEMPERATURE READING. c. THE ZONE IS EDITED TO BE A VOTER IN THE RTU'S CONTROLS SETUP (THROUGH THE "INCLUDE IN CHANGEOVER" CHECKBOX). d. THE ZONE IS NOT TAGGED BY THE RTU'S CONTROLS (SEE VAV ZONE TAGGING BELOW).

VAV ZONE TAGGING FOR NO VOTE1. A VAV ZONE IS TAGGED AND EXCLUDED FROM THE VOTING DECISION IF ANY OF THE FOLLOWING ARE PRESENT: a. THE SYSTEM IS NOT IN MORNING WARM-UP OR PRE-COOL. b.THE ZONE IS RECEIVING ITS DESIRED SUPPLY AIR AND THE HEAT COOL MODE MATCHES THAT OF THE RTU MEMBER. c.THE ZONE TEMPERATURE IS FARTHEST AWAY FROM THE SETPOINT OF ALL VOTING ZONES RECEIVING THE DESIRED SUPPLY AIR. d. THE ZONE TEMPERATURE REMAINS THREE OR MORE DEGREES AWAY FROM THE SETPOINT FOR 60 MINUTES. e. THE TAGGED ZONE CONTINUES TO OPERATE AND COMMUNICATE NORMALLY BUT CANNOT VOTE FOR HEAT OR COOL. THIS PREVENTS ONE ZONE FROM DRIVING THE COMFORT OF ALL OTHER ZONES IF ITS SETPOINTS OR LOAD CANNOT BE SATISFIED. 2. THE ZONE BECOMES AN ELIGIBLE VOTER WHEN: a. IT RETURNS TO WITHIN 1 °F OF ITS ACTIVE SETPOINT. b. THE SYSTEM BECOMES UNOCCUPIED. c. VAV TAGGING IS DISABLED.

ZONE HEAT/COOL CALL STRENGTH1. AFTER THE HEAT/ COOL MODE OF THE ZONE IS DECIDED THE STRENGTH OF ITS HEATING OR COOLING CALL IS DETERMINED. a. COOL CALLER: A VAV BECOMES A "COOL CALLER" IF IT IS A VOTING VAV AND ITS ZONE TEMPERATURE IS MORE THAN 1° F ABOVE THE ACTIVE COOLING SETPOINT. A VAV LOSES ITS COOL CALL STATUS IF IT BECOMES A NON-VOTER OR IF ITS ZONE TEMPERATURE IS LESS THAN THE ACTIVE COOLING SETPOINT PLUS 0.5° F. b. STRONG COOL CALLER: A VAV BECOMES A "STONG COOL CALLER" IF IT IS A VOTING VAV AND ITS ZONE TEMPERATURE IS MORE THAN 2° F ABOVE THE ACTIVE COOLING SETPOINT. A VAV LOSES ITS STRONG COOL CALLER STATUS IF IT BECOMES A NON-VOTER OR IF ITS ZONE TEMPERATURE IS LESS THAN THE ACTIVE COOLING SETPOINT PLUS 1°F. c. HEAT CALLER: A VAV BECOMES A "HEAT CALLER" IF IT IS A VOTING VAV, AND ITS ZONE TEMPERATURE IS MORE THAN 2°F BELOW ACTIVE HEATING SETPOINT. A VAV LOSES ITS HEAT CALLER STATUS IF IT BECOMES A NON-VOTER OR IF ITS ZONE TEMPERATURE IS GREATER THAN THE ACTIVE HEATING SETPOINT MINUS 1.5°F. d. STRONG HEAT CALLER: A VAV BECOMES A "STRONG HEAT CALLER" IF IT IS A VOTING VAV AND ITS ZONE TEMPERATURE IS MORE THAN 3°F BELOW THE ACTIVE HEATING SETPOINT.A VAV LOSES ITS "STRONG HEAT CALLER" IF IT BECOMES A NON-VOTER OR IF ITS ZONE TEMPERATURE IS GREATER THAN THE ACTIVE HEATING SETPOINT MINUS 2° F

HEAT/COOL DECISION AND CONTROL OF THE RTU1. THE RTU CONTROLS PROGRAM DETERMINES THE QUANTITY AND THE STRENGTH OF ALL HEATING AND COOLING CALLS. AT POWER UP AND ON TRANSITION FROM UNOCCUPIED TO OCCUPIED, THE GREATER NUMBER OF HEAT OR COOL CALLS DETERMINES THE HEAT/COOL MODE OF THE AC SYSTEM. IF ALL THE SPACES ARE SATISFIED ( NO CALL) THE SYSTEM SHALL SEND A FAN ONLY REQUEST TO THE RTU.2. THE RTU CONTROLS SETS THE SUPPLY TEMPERATURE SETPOINT OF THE RTU, TAKING INTO CONSIDERATION THE VAV MEMBER'S DEVIATION FROM SETPOINT. IF ALL MEMBERS ARE SATISFIED ( NO VOTES), THE RTU SHALL BE IN "FAN ONLY. WHEN THE VAV'S NEED HEAT OR COOL, THE RTU'S CONTROLS SETS THE HEAT/COOL MODE ACCORDINGLY.

ECONOMIZING: WHEN SPACE TEMPERATURE RISES ABOVE THE THERMOSTAT'S COOLING SETPOINT AND THE OUTSIDE AIR ENTHALPY IS AT OR BELOW THEECONOMIZER SETPOINT, THE FAN SHALL ENERGIZE AND THE OUTSIDE AIR DAMPER AND RELIEF DAMPER SHALL MODULATE OPEN AND THERETURN AIR DAMPER SHALL MODULATE CLOSED TO MAINTAIN A 53°F MIXED AIR TEMPERATURE. THE POWERED EXHAUST FAN SHALL ENERGIZE TOMAINTAIN BUILDING PRESSURIZATION (WHERE APPLICABLE). IF MIXED AIR EXCEEDS SETPOINT AND THE SPACE TEMPERATURE CONTINUES TORISE, THE REFRIGERATION CIRCUIT SHALL BE ENERGIZED. ON A FALL IN SPACE TEMPERATURE THE REVERSE SHALL OCCUR.

UNOCCUPIED MODE1. WHEN THE SYSTEM IS INDEXED TO THE UNOCCUPIED MODE THE FOLLOWING SHALL OCCUR. a. FAN SHALL BE INDEXED TO "AUTO" b. OUTSIDE AIR DAMPER SHALL REMAIN CLOSED c. RETURN AIR DAMPER SHALL BE INDEXED TO THE OPEN POSITION (100%) d. THE HEATING & COOLING CIRCUITS SHALL CYCLE TO MAINTAIN SET BACK TEMPERATURES.

NO SCALE

PACKAGED ROOFTOP VAV HEATING / COOLING

HONEYWELLCOMMERCIALTHERMOSTAT

ROOF TOP AIRCONDITIONING UNIT

S

WITH ECONOMIZER (RTU-1 & 8)

VAV - B

VAV - C

VAV - D

VAV - E

TRANE

TRANE

TRANE

TRANE

TRANE

12.5

10

3

3

3

15

15

DOWNFLOW

DOWNFLOW

DOWNFLOW

1.75"

CONSTANT VOLUME UNIT W/ DX COOLING & GAS HEAT

CONSTANT VOLUME UNIT W/ DX COOLING & GAS HEAT

1.0"

0.75"

VARIABLE

2

0.5

0.5

0.5

675EF-M-2

750EF-P-1

400EF-P-2

MUNICIPAL PUBLIC BATHROOMS

POLICE LOCKERS AND BATHROOMS

POLICE LAB HOODRTC

4 RTC- ROOFTOP CENTRIFUGAL FAN.

3

1 3

2 4

1 3SQ-090-VG1 /6 1495 7.6 3.4 41 LBS

SQ-100-VG

SQ-100-VG

1 /4

1 /4 120-V - 1Ø - 60 Hz

120-V - 1Ø - 60 Hz

120-V - 1Ø - 60 Hz

56 LBS56 LBS GREENHECK

GREENHECK

GREENHECK

G-099-VG54 LBS1 /4

1263

12631384 9.1

6.4

6.4 3.73.7

2.85INLINE

INLINE

5000

4000

1100

25-170 4"Ø VCCF

VCCF

VCCF

VCCF

VCCF

5"Ø

6"Ø

8"Ø

10"Ø

50-260

60-380

105-680

165-1000

OPEN/SHUTVAV - F TRANE VCCF12"Ø240-1500

460-3-60

460-3-60

460-3-60

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

- - - -

150940

5000

4000

1100

4539MODULATING250.0114.616380/678675750

PROVIDE ROOF CURB ADAPTERS FOR UNIT INSTALLATION, VAV OVERSIZED MOTOR W/ SHAFT GROUND RING,(3) VARIABLE SPEED COMPRESSORS- MODULATING 4% TO 100%,CF, FF AND CONDENSATE OVERFLOW SWITCH, DEMAND VENTILATION CONTROLS,MODULATING GAS HEAT 2.5:1, CO2 SENSOR DUCT MOUNTED,POWER EXHAUST, ECONOMIZER,THROUGH THE BASE ELECTRICAL WITH CIRCUIT BREAKER,THROUGH THE BASE ELECTRICAL WITH DISCONNECT SWITCH,REFERENCED OR COMPARATIVE ENTHALPY,COMPARATIVE ENTHALPY, VAV OPERATION, UNIT AND COMPONENTS SHALL BE ULTRA HIGH CONSTRUCTION, MICROPROCESSOR CONTROLS, HUMIDITY DUCT MOUNTED SENSOR, DIRTY FILTER SWITCH, POWERED WEATHERPROOF GFI OUTLET, CONNECTCONDENSATE DRAIN TO EXISTING HORIZONTAL DRAIN ON ROOF, BAROMETRIC RELIEF, MC SHALL INSTALL SMOKE DETECTOR IN RETURN DUCT MAIN, DISCONNECT GAS LINES FROM UNITS BEING REMOVED AND RECONNECT GAS LINES TO NEW INSTALLEDUNITS..

- - - -

3

3

YZC120F4RVA12.2/23.0 15404531188.0108.3561.25

80.0101.447.3 64.0

86.56107.3760.21/58.5480/67VARIABLE2.75

24.6734.0959.6/57.1380/670.75

600

165

VARIABLE - - - - MODULATING

CONSTANT VOLUME UNIT W/ DX COOLING & GAS HEAT

CONSTANT VOLUME UNIT W/ DX COOLING & GAS HEAT

CONSTANT VOLUME UNIT W/ DX COOLING & GAS HEAT

CONSTANT VOLUME UNIT W/ DX COOLING & GAS HEAT

1

1

1

1

1

1

1 PROVIDE CONTROL STATS FOR EACH VAV BOX.

2

YHC037E4RMA13.0/17.5 7671512

4 PROVIDE ROOF CURB ADAPTERS FOR UNIT INSTALLATION, ECON-COMP ENTHALPY 0-100%, CFS FFS & COND DP OVERFLOW SWITCH, DEMAND CONTROL VENTILATION (CO2), CO2 DUCT MOUNTED ZONE SENSOR, ECONOMIZER,POWER EXHAUST, BAYSENS119PROGRAMMABLE ZONE TEMPERATURE STAT, SINGLE ZONE CONSTANT VOLUME, THROUGH THE BASE ELECTRICAL WITH DISCONNECT SWITCH,ECONOMIZER,REFERENCED OR COMPARATIVE ENTHALPY, MICROPROCESSOR CONTROLS, HUMIDITY DUCT MOUNTEDSENSOR, DIRTY FILTER SWITCH, POWERED WEATHERPROOF GFI OUTLET, CONNECT CONDENSATE DRAIN TO EXISTING HORIZONTAL DRAIN ON ROOF, DISCONNECT GAS LINES FROM UNITS BEING REMOVED AND RECONNECT GAS LINES TO NEW INSTALLED UNITS..

1905

110.07142.1959.98/58.02 YZD150F4RVC12.4/19.60 2550

ADD-ALT

ADD-ALT

ADD-ALT

ADD-ALT

ADD-ALT

RTU-8 TRANEMERV 812.5 DOWNFLOWVAV UNIT W/ DX COOLING & GAS HEAT 5000 460-3-60 YZD150F4RVC12.4/19.60 25504539MODULATINGVARIABLE 250.0114.6163110.07142.1959.98/58.0280/671.75"5000 8675750 - - - - 3

RTU-2 17.5 DOWNFLOWCONSTANT VOLUME UNIT W/ DX COOLING & GAS HEAT 4955 4955 750 - - - - - - - -TRANE- EXSITING- - - - - - - - - - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -- - - -

DOWNFLOW

DOWNFLOW

DOWNFLOW

DOWNFLOW

780

5730

780

5730

120

600

4955 4955 750

940

4

SR SUPPLY STEEL WHITE 25LOUVER PRICEOBDREFER TO PLAN REFER TO PLAN 520 DOUBLE DEFLECTION BLADES.

AS

N

OT

ED

JM

F

DF

UNITNO.

1. ALL PLUMBING WORK SHALL BE IN ACCORDANCE WITH THE CURRENT PLUMBING CODE AND ALLAPPLICABLE LOCAL CODES AND DRAWINGS.

2. ALL MATERIALS AND EQUIPMENT SHALL BE NEW.3. MANUFACTURERS' MODEL NUMBERS ARE SPECIFIED SOLELY TO ESTABLISH STANDARDS OF QUALITY

FOR PERFORMANCE AND MATERIALS.4. PRODUCT INSTALLATION SHALL ADHERE TO MANUFACTURERS RECOMMENDATIONS.5. PROVIDE ACCESS PANELS FOR EQUIPMENT THAT REQUIRES PERIODIC SERVICE & TO ACCESS VALVES

AND ALL CONCEALED MECHANICAL EQUIPMENT.6. CONTRACTOR SHALL COORDINATE ELECTRICAL CHARACTERISTICS AND REQUIREMENTS OF ALL

PLUMBING EQUIPMENT WITH THE ELECTRICAL DRAWINGS.7. ALL PLUMBING EQUIPMENT, PIPING, INSULATION, ETC., INSTALLED IN HVAC PLENUM SPACES SHALL

MEET CODE REQUIREMENTS FOR SMOKE AND COMBUSTIBILITY.8. PROVIDE SHUTOFF VALVES ON ALL BRANCH PIPING AND ON ALL SUPPLIES TO INDIVIDUAL FIXTURES

AND EQUIPMENT. PROVIDE BALL VALVES ON ALL WATER MAIN BRANCHES IN CORRIDORS AND WHEREINDICATED ON DRAWINGS. ALL VALVES SHALL BE ACCESSIBLE.

9. SUPPORT ALL EQUIPMENT PIPING FROM BLDG STRUCTURE TO PROVIDE A VIBRATION FREEINSTALLATION. NOTIFY STRUCTURAL ENGINEER OF ALL WEIGHTS AND METHODS OF SUPPORT.

10. RUN PIPING CONCEALED, UNLESS SPECIFIED OTHERWISE, AND CLEAR OF CEILING INSERTS.11. PROVIDE CLAMPS, OFFSETS, EXPANSION JOINTS, ANCHORS AND GUIDES AS NECESSARY TO PREVENT

STRESS ON PIPING.12. PROVIDE VENTS AT HIGH POINTS IN PIPING SYSTEMS AND DRAIN VALVES AT LOW POINTS.13. PROVIDE AT LEAST THREE-ELBOW SWING FOR PIPE TAKE-OFFS TO RISERS.14. HORIZONTAL SANITARY PIPING 2 1/2" AND SMALLER TO BE PITCHED A MINIMUM OF 1/4" PER FOOT IN

THE DIRECTION OF THE FLOW.15. HORIZONTAL SANITARY PIPING 3" AND UP TO AND INCLUDING 6" TO BE PITCHED AT A MINIMUM OF 1/8"

PER FOOT IN THE DIRECTION OF FLOW.16. HORIZONTAL SANITARY PIPING GREATER THAN 6" TO BE PITCHED A MINIMUM OF 1/16" PER FOOT IN

THE DIRECTION OF FLOW.17. CLEANOUTS SHALL BE PROVIDED AT THE BASE OF ALL SANITARY AND RAIN WATER VERTICAL STACKS.18. ANY REFERENCE TO ELECTRICAL, PLUMBING AND HVAC CONTRACTORS, NOTED ON THESE DRAWINGS

OR STATED IN THE SPECIFICATIONS SHALL NOT BE MISCONSTRUED AS AN INTENTION TO DEFINESEPARATE CONTRACTORS FOR THE RESPECTIVE WORK. THE GENERAL CONTRACTOR SHALLCO-ORDINATE AND PROVIDE A COMPLETE BUILDING WITH COMPLETE MECHANICAL AND ELECTRICALSYSTEMS, REGARDLESS OF ANY SPECIFICATION REFERENCES TO OTHER CONTRACTORS.

ACRYLIC SHOWER MODULECOMFORTDESIGNS

XSA4136BF.75 43 1/4"x36 1/4"x82 7/8" --- --- ---

SINGLE BOWL SINK ELKAY 20 GAUGE STAINLESS STEELHD320874LFR 15" x 15" x 6" DECK MOUNTED FAUCET, LEVER HANDLES ---

2" C.B. CAST BRASS

1 1/2" C.B. CAST BRASS W/CLEANOUT PLUG

Z5755-U SLOAN #8180-1.0BATTERY POWERED SENSOR OPERATED

FLUSHOMETERINTEGRALURINAL ZURN WALL HUNG 1.0 GPF ---

KOHLERUNDERMOUNT LAVATORY 20 GAUGE STAINLESS STEELK-2608-SU 19 7/8" x 16 11/16" SLOAN #ESD-2101-CPBATTERY POWERED SENSOR OPERATED

FAUCET & SOAP COMBOPROVIDE TRUEBRO #102W & 105W SUPPLY & WASTE PIPING INSULATION---

1 1/2" C.B. CAST BRASS W/CLEANOUT PLUG

---

DP, DN

VTR

WC

WH

UR

TYP

UP

V

TEE LOOKING UP

WALL HYDRANT

WATER CLOSET

TEE LOOKING DOWN

VENT THRU ROOF

TYPICAL

URINAL

VENT

140 HW

BLDG

ARCH

DWG

DP, DN

COND

MSB

140

SAN

NTS

RBF

SAN

RAF

RAC

LAV

IWR

MFR

G

HWR

G

HW

HB

CO

FLR

UP

FD

CD

ED ED

DN

CTE

CO

CW

AFF

AP

ELBOW DOWN OR DROP

ELBOW UP OR RISE

FLOOR CLEANOUT

HOT WATER

INDIRECT WASTE RECEPTOR

MANUFACTURER

NOT TO SCALE

RUN BELOW FLOOR

HOT WATER RETURN

MOP SERVICE BASIN

RUN ABOVE FLOOR

RUN ABOVE CEILING

FLOW IN DIRECTION OF ARROW

HOSE BIBB W/ VACUUM BREAKER

FLOOR DRAIN

140

P-TRAP

SANITARY

LAVATORY

GAS

FLOOR

EMERGENCY DRAIN

ACCESS PANEL

BALL VALVE

CHECK VALVE

CONDENSATE

COLD WATER

CONNECT TO EXISTING

DIRECTION OF SLOPE

ABOVE FINISHED FLOOR

DOWN

DRAWING

BUILDING

WALL CLEANOUT

ARCHITECT

RWC RAIN WATER CONDUCTOR

RCP REINFORCED CONCRETE PIPE

RWC

W/ PRESSURE BALANCING MIXING VALVE, HAND HELD SHOWER ASSEMBLYWITH SLIDE BAR, VACUUM BREAKER AND 60" HOSE.

WDP WASHING MACHINE DRAIN PAN

ELKAY #LK2477CR

2# HIGH PRESSURE 2 PSI GAS2#

DOUBLE BOWL SINK DAYTON 23 GAUGE STAINLESS STEELK233224DF 33 1/2"x22"x6 1/16" ELKAY #LK2478CR LEVER HANDLE ------1 1/2" W/ CLEANOUT PLUG

1. PIPE MATERIALSA. SERVICE: ABOVE GROUND WATER PIPING

PIPE MATERIAL: TYPE L COPPER TUBING ASTMB882 FACTORY.FITTING MATERIAL: WROUGHT COPPER AND BRONZE SOLDER JOINTS.PIPE JOINT: 95-5 LEAD FREE SOLDER

B. SERVICE: SANITARY WASTE & VENT (ABOVE GRADE)PIPE MATERIAL: SERVICE WEIGHT CAST IRON NO-HUB CONFORMING TO CS 301, TYPE ME COPPERTUBINGFITTING MATERIAL: CAST IRON DRAINAGE PATTERN, WROUGHT COPPER DRAINAGE PATTERN TOSUIT PIPE MATERIALPIPE JOINT: HEAVY DUTY CISPI APPROVED STAINLESS STEEL NO-HUB COUPLING W/ NEOPRENEGASKET, 95-5 SOLDER FOR COPPER.

2. VALVESA. BALL VALVES 2" AND SMALLER ON WATER SERVICES SHALL BE 2 PIECE ALL BRONZE WITH FULL

PORT STAINLESS STEEL BALL, TEFLON SEATS, SOLDER ENDS AND 600 PSI COLD WORKINGPRESSURE: JENKINS 902, APOLLO OR WATTS APPROVED EQUAL, UNLESS OTHERWISE NOTED.

3. INSULATIONA. INSULATION SHALL BE BY OWENS CORNING, CERTAIN-TEED OR MANVILLE.B. INSULATION, JACKETS AND ADHESIVES SHALL BE FLAME RETARDANT AND SHALL HAVE ASTM E-84

FIRE HAZARD RATINGS OF 25 FLAME SPREAD, 50 SMOKE DEVELOPED AND 50 FUEL CONTRIBUTED.C. DOMESTIC HOT WATER: NEW DOMESTIC HOT WATER PIPING SUPPLY AND RECIRCULATION PIPING

SHALL BE INSULATED WITH HEAVY DENSITY FIBERGLASS WITH SELF-SEALING LAP AND ALLSERVICE JACKET. FITTINGS AND VALVES SHALL BE INSULATED WITH TWO LAYERS BLANKETINSULATION WITH PVC COVERS. INSULATION SHALL BE RATED FOR MAXIMUM OPERATINGTEMPERATURE OF 450 DEGREES F. REFER TO PIPE INSULATION MATRIX ON THIS SHEET FORREQUIRED INSULATION THICKNESS.

D. DOMESTIC COLD WATER: NEW COLD WATER SUPPLY PIPING, VALVES AND FITTINGS SHALL BEINSULATED AS SPECIFIED FOR HOT WATER SUPPLY PIPING, IN ADDITION, CONTINUOUS VAPORBARRIER SHALL BE MAINTAINED. REFER TO PIPE INSULATION MATRIX ON THIS SHEET FORREQUIRED INSULATION THICKNESS.

E. RAIN WATER CONDUCTOR: HORIZONTAL RAIN WATER CONDUCTORS SHALL BE INSULATED WITHMINIMUM 1" THICK INSULATION.

4. HANGERS, ANCHORS, CLAMPS AND INSERTSA. PROVIDE CAST BRASS SPLIT RING HINGE HANGERS, SUPPORT PIPING FROM BUILDING STRUCTURE

TO MAINTAIN REQUIRED GRADE AND PITCH OF PIPE LINES, PREVENT VIBRATION, SECURE PIPINGIN PLACE. SECURE HANGERS TO INSERTS WHERE PRACTICAL. HANGER RODS SHALL HAVEMACHINE THREADS.

B. HANGER RODS SHALL BE CONNECTED TO BEAM CLAMP, UL APPROVED CONCRETE INSERTS ORPHILLIPS SHALL BE APPROVED EQUAL EXPANSION SHIELD. RAMSET OR POWER DRIVEN INSERTSWILL NOT BE ALLOWED.

C. HANGER SPACING SHALL MEET REQUIREMENTS OF STATE AND LOCAL CODES.5. SLEEVES AND PENETRATIONS

A. PIPE SLEEVES THROUGH FIRE RATED CONSTRUCTION SHALL BE SCHEDULE 40 STEEL. SLEEVESTHROUGH PARTITIONS AND NON FIRE RATED CONSTRUCTION SHALL BE 26 GAUGE GALVANIZEDSTEEL WITH LOCAL LONGITUDINAL SEAMS.

B. PACKING FOR SLEEVES THAT DO NOT REQUIRE MAINTENANCE OF FIRE RATINGSHALL BE OAKUM,SILICATE FOAM, CERAMIC FIBER WITH APPROVED SEALANT. PACK OR FOAM TO WITHIN ONE INCHOF BOTH WALL SURFACES. SEAL PENETRATION PACKING WITH APPROVED CAULKING ANDPAINTABLE WATERPROOF MASTIC SURFACE FINISH OR SILICONE CAULKING.

6. TESTINGA. TEST AND ADJUST PLUMBING SYSTEMS AS REQUIRED BY ARCHITECT AND AUTHORITIES THAT HAVE

JURISDICTION. PERFORM TEST RECOMMENDED BY MANUFACTURERS OF MATERIAL ANDEQUIPMENT; THIS REQUIREMENT MAY BE WAIVED BY ARCHITECT. TEST PLUMBING SYSTEMSUNDER PRESSURE AND HEADS SPECIFIED IN PLUMBING CODES. CLEAN SYSTEMS THOROUGHLYBEFORE TESTING. FIXTURES, EQUIPMENT, PIPE, VALVES AND FITTINGS SHALL BE FREE OF GREASE,METAL CUTTINGS, DIRT AND OTHER FOREIGN MATERIAL. REPAIR STOPPAGE, DISCOLORATION ANDDAMAGE TO PARTS OF BUILDING, FINISHES AND FURNISHINGS DUE TO FAILURE TO PROPERLYCLEAN PIPING SYSTEM.

7. DISINFECTION OF WATER SYSTEMSA. WATER PIPING SYSTEMS SHALL BE THOROUGHLY DISINFECTED WITH A SOLUTION CONTAINING NO

LESS THAN 50 PARTS PER MILLION OF AVAILABLE CHLORINE. CHLORINATING MATERIALS SHALLBE EITHER LIQUID CHLORINE OR SODIUM HYPOCHLORITE SOLUTION, SHALL BE INTRODUCED INTOTHE SYSTEM AND DRAWN TO ALL POINTS IN THE SYSTEM. DISINFECTION SOLUTION SHALL BEALLOWED TO REMAIN IN SYSTEM FOR 24 HOURS, DURING THIS TIME, VALVES AND FAUCETSSHALL BE OPENED AND CLOSED SEVERAL TIMES. AFTER DISINFECTION, SOLUTION SHALL BEFLUSHED FROM THE SYSTEM WITH CLEAR WATER UNTIL RESIDUAL CHLORINE CONTENT IS NOGREATER THAN 2 PARTS PER MILLION.

8. IDENTIFICATION OF PLUMBING SYSTEMS:A. PROVIDE PIPING IDENTIFICATION LABELS AND DIRECTIONAL ARROWS ON ALL PLUMBING SYSTEMS.

INSTALL LABELS AT 10' INTERVALS & AT EACH SIDE OF FLOOR & WALL SEPARATIONS.B. PROVIDE VALVE TAGS AT EACH DOMESTIC WATER SHUTOFF VALVE. PROVIDE VALVE TAG INDEX

IDENTIFYING VALVE NUMBER, LOCATION AND SERVICE.9. MISCELLANEOUS

A. ALL PLUMBING WORK SHALL BE IN ACCORDANCE WITH THE CURRENT PLUMBING CODE AND ALLAPPLICABLE CODES AND STANDARDS

B. PROVIDE SHUTOFF VALVES ON ALL BRANCH PIPING AND ON ALL SUPPLIES TO INDIVIDUAL FIXTURESAND EQUIPMENT. PROVIDE BALL VALVES ON ALL WATER MAIN BRANCHES IN CORRIDORS ANDWHERE INDICATED ON DRAWINGS. ALL VALVES SHALL BE ACCESSIBLE.

C. PROVIDE VENTS AT HIGH POINTS IN PIPING SYSTEMS AND DRAIN VALVES AT LOW POINTS.D. PROVIDE AT LEAST THREE-ELBOW SWING FOR PIPE TAKE-OFFS TO RISERS.E. PITCH PIPING MINIMUM 1/8" PER 1'-0" TOWARDS DIRECTION OF FLOW TO ALLOW FOR DRAINING.F. FLOOR CLEANOUTS SHALL BE JR SMITH 4031 SERIES.G. WALL CLEANOUTS SHALL BE JR SMITH 4436 SERIES.H. PROVIDE TRAP GUARDS ON ALL FLOOR DRAINS.I. WHERE PIPING (DOMESTIC WATER, SANITARY, VENT, GAS, ETC.) IS LOCATED WITHIN WALLS,

PROVIDE NAILER PLATES WHERE PIPING IS LOCATED WITHIN 1 1/2" OF THE FRAMING MEMBER.

ELONGATED BOWL,VITREOUS CHINA

ADA WATER CLOSETFLUSH VALVE

1.6 GPF SLOAN #8111 --- SOLID PLASTIC, OPEN FRONT SEAT W/O COVER, COMFORT SEATS #C104C1301MANSFIELDBATTERY POWERED SENSOR OPERATED

FLUSHOMETER

REFRIGERATOR OUTLET BOXW/ 1/4 TURN VALVE. PROVIDE FIRE RATED MODEL WHEN LOCATED INA RATED WALL.

DESCRIPTIONSYMBOLMFGR MODEL

FIXTURE

TYPE SIZE

PLUMBING FIXTURE SCHEDULE

TYPE SUPPLYTRAP COLOR CARRIER REMARKS

WC-1

UR-1

LAV-1

SHO-1

SK-1

SK-2

MFGR

INTEGRAL

---

1" SUPPLY

3/4" SUPPLY

1/2" SUPPLIES, ANGLE STOP, C.B.ESCUTCHEON

1/2" SUPPLIES

1/2" SUPPLIES, ANGLE STOP, C.B.ESCUTCHEON

1/2" SUPPLIES, ANGLE STOP, C.B.ESCUTCHEON

WHITE

WHITE

LUSTER

WHITE

STAINLESS STEEL

STAINLESS STEEL

DESCRIPTION MFGR MODEL NO. REMARKS

PLUMBING SPECIALTIES

OATEYROB-1 ICE MAKER OUTLET BOX

PLUMBING GENERAL NOTES LEGEND

PLUMBING NOTES AND SPECIFICATIONS

ACRYLIC

GENERAL SPECIFICATIONS

1. DRAWINGS AND SPECIFICATIONS FORM COMPLIMENTARY REQUIREMENTS; PROVIDE WORK SPECIFIEDAND NOT SHOWN, AND WORK SHOWN BUT NOT SPECIFIED AS THOUGH EXPLICITLY REQUIRED BY BOTH.ALTHOUGH WORK IS NOT SPECIFICALLY SHOWN OR SPECIFIED, PROVIDE SUPPLEMENTARY ORMISCELLANEOUS ITEMS, APPURTENANCES, DEVICES AND MATERIALS OBVIOUSLY NECESSARY FOR ASOUND, SECURE AND COMPLETE INSTALLATION.

2. THE DRAWINGS AND SPECIFICATIONS INDICATE A PERFORMANCE SPECIFICATION FOR THE FIREPROTECTION AND FIRE ALARM SYSTEMS. AWARDED CONTRACTORS ARE RESPONSIBLE FOR DETAILEDDESIGN AND PREPARATION OF SIGNED AND SEALED ENGINEERING DOCUMENTS FOR REVIEW/APPROVALFROM OWNERS INSURANCE CARRIER AND LOCAL AUTHORITY HAVING JURISDICTION.

3. DRAWINGS ARE DIAGRAMMATIC: THE CONTRACTOR IS RESPONSIBLE FOR PROVIDING ALL COMPONENTSNECESSARY FOR A COMPLETE INSTALLATION. DETERMINE LOCATIONS OF SYSTEMS AND COMPONENTSIN FIELD. COORDINATE WITH ARCHITECTURAL DRAWINGS AND OTHER TRADES.

4. ADDRESS QUESTIONS REGARDING DRAWINGS TO ARCHITECT IN WRITING BEFORE AWARD OF CONTRACT.OTHERWISE, ARCHITECT'S INTERPRETATION OF MEANING AND INTENT OF DRAWINGS SHALL BE FINAL.

5. THE INTENTION IS FOR INSTALLATION OF COMPLETE AND OPERATING SYSTEMS INSTALLED INACCORDANCE WITH THE ASSOCIATED MANUFACTURER'S INSTRUCTIONS. NOT EVERY COMPONENTREQUIRED IS SHOWN. THE CONTRACTOR SHALL INCLUDE ALL COMPONENTS NORMALLY ASSOCIATEDWITH THE PARTICULAR SYSTEM AND/OR REQUIRED BY THE MANUFACTURER'S INSTALLATIONINSTRUCTIONS. THE SYSTEM SHALL BE FULLY COMMISSIONED AND SIGNED OFF BY AN OFFICER OF THERESPECTIVE CONTRACTOR. PRIOR TO FINAL OWNER ACCEPTANCE TESTING, PROVIDE PERSONNEL TOASSIST IN 24 HOURS OF ACCEPTANCE TESTING.

6. PRIOR TO COMMENCING WORK, COORDINATION DRAWINGS MUST BE PREPARED AND SUBMITTED FORREVIEW AND APPROVAL TO THE ARCHITECT/ENGINEER. EACH TRADE (HVAC, PLUMBING, ELECTRIC, ANDFIRE PROTECTION) IS RESPONSIBLE FOR DOCUMENTING THEIR WORK ON THE PLAN ORIGINALLYSUBMITTED AS THE SPRINKLER PIPE FABRICATION DRAWING. LOCATION AND ELEVATION OF THERESPECTIVE DISCIPLINE'S WORK MUST BE SHOWN ON THE COORDINATION DRAWINGS. SHEETMETALSHOP DRAWINGS SHALL INCLUDE ALL ELEMENTS OF THE EQUIPMENT, DUCTWORK, AIR DEVICES, ANDREFLECTED CEILING PLAN FOR COORDINATION OF CRITICAL DIMENSIONS OF ARCHITECTURAL/STRUCTURAL COMPONENTS.

7. GIVE NOTICES, FILE PLANS, OBTAIN PERMITS AND LICENSES, PAY FEES AND BACK CHARGES, ANDOBTAIN NECESSARY APPROVALS FROM AUTHORITIES THAT HAVE JURISDICTION AS REQUIRED TOPERFORM WORK IN ACCORDANCE WITH ALL LEGAL REQUIREMENTS AND WITH THE DESIGN DOCUMENTS

8. PRIOR TO COMMENCING WORK, CONTRACTOR SHALL SUBMIT SHOP DRAWINGS AND EQUIPMENT DATAFOR MATERIALS AND EQUIPMENT TO THE ARCHITECT FOR REVIEW AND APPROVAL. MATERIALS ANDEQUIPMENT SHALL NOT BE INSTALLED BEFORE SHOP DRAWINGS ARE REVIEWED AND APPROVED.SCHEDULE AT LEAST TEN WORKING DAYS, EXCLUSIVE OF TRANSMITTAL TIME, FOR SUBMITTAL REVIEWSHALL BE ALLOWED.

9. MATERIALS AND EQUIPMENT SHALL BE LISTED BY UNDERWRITERS LABORATORIES (UL) AND APPROVEDBY ASME AND AGA FOR INTENDED SERVICE.

10. THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS,TECHNIQUES, SEQUENCES AND PROCEDURES REQUIRED FOR SAFE EXECUTION AND COMPLETION OFWORK, AND FOR INITIATING, MAINTAINING AND SUPERVISING ALL SAFETY PRECAUTIONS ANDPROGRAMS IN CONNECTION WITH THE WORK.

11. COORDINATE WORK OF THIS SECTION WITH THAT OF OTHER SECTIONS.12. ALL MATERIALS, EQUIPMENT AND METHOD OF INSTALLATION SHALL BE ACCORDANCE WITH THE

STANDARDS, REGULATIONS, CODES, ORDINANCES, AND LAW OF LOCAL, STATE, AND FEDERALGOVERNMENTS, AND OTHER AUTHORITIES THAT HAVE LAWFUL JURISDICTION.

13. IT SHALL BE THE RESPONSIBILITY OF THIS CONTRACTOR TO COORDINATE HIS WORK WITH THAT OF ALLOTHER TRADES, INCLUDING (BUT NOT LIMITED TO), ELECTRICAL, HVAC, SPRINKLER, PLUMBING,STRUCTURAL AND GENERAL ARCHITECTURE. OFFSETS IN PIPING AND OFFSETS AROUND OBSTRUCTIONSSHALL BE PROVIDED AT NO ADDITIONAL COST TO THE OWNER.

14. DEVIATION FROM CONTRACT DOCUMENTS, OR PROPOSED SUBSTITUTION OF MATERIALS OR EQUIPMENT FOR THOSE SPECIFIED, SHALL BE REQUESTED IN SEPARATE LETTER, WHETHER DEVIATIONS ARE DUE TO FIELD CONDITIONS, STANDARD SHOP PRACTICE OR OTHER CAUSE. THE CONTRACTOR IS RESPONSIBLE FOR ANY COSTS INCURRED AS A RESULT OF THE CHANGES NEEDED TOACCOMMODATE THE SUBSTITUTED EQUIPMENT INCLUDING THE WORK OF OTHER TRADES.

15. EACH CONTRACTOR IS RESPONSIBLE FOR ITS CUTTING AND PATCHING REQUIRED FOR THEINSTALLATION OF ITS NEW WORK. CUTTING AND PATCHING SHALL BE COMPLETED IN A NEAT ANDWORKMANLIKE MANNER. PATCHING MATERIALS SHALL MATCH EXISTING MATERIALS TO THEGREATEST EXTENT POSSIBLE. PROVIDE TOUCH-UP TO MATCH EXISTING SURROUNDING AREAS OFCUTTING AND PATCHING WORK

16. INTERRUPTIONS TO EXISTING SERVICES AND SYSTEMS SHALL BE AS SHORT AS POSSIBLE AND AT ATIME AND DURATION APPROVED BY THE OWNER. INCLUDE ALL PREMIUM TIME ASSOCIATED WITHINTERRUPTIONS. INTERRUPTIONS SHALL BE SCHEDULED WITH OWNER 48 HOURS IN ADVANCE.

17. PROVIDE CHASE COORDINATION DRAWINGS PRIOR TO CONSTRUCTION DOCUMENTING ALL UTILITIESTHROUGH CHASES FOR ALL TRADES. PROVIDE SUBMITTAL FOR ENGINEER'S REVIEW PRIOR TOCONSTRUCTION.

18. CONTRACTOR SHALL COORDINATE ITS RESPECTIVE CEILING MOUNTED EQUIPMENT WITH OTHER TRADECONTRACTORS PRIOR TO INSTALLATION TO AVOID CONFLICTS.

19. ANY DEMOLITION SHALL BE COORDINATED WITH OWNER, ARCHITECT, G.C. AND ENGINEER. ALL DEBRISSHALL BE CLEANED UP AND REMOVED FROM THE SITE BY THE END OF THE DAY. PRIOR TO DISPOSAL OFEQUIPMENT AND MATERIALS, TURN OVER TO THE OWNER ANY REMOVED EQUIPMENT AND MATERIALSPER OWNERS REQUEST.

20. WORK SHALL BE EXECUTED IN A WORKMANLIKE MANNER AND SHALL PRESENT NEAT, RECTILINEARAPPEARANCE WHEN COMPLETED. MAINTAIN MAXIMUM HEAD ROOM AT ALL TIMES. DO NOT RUN PIPES,DUCTS, AND CONDUIT EXPOSED UNLESS SHOWN AND NOTED TO BE EXPOSED ON DRAWINGS.MATERIALS AND EQUIPMENT SHALL BE NEW AND INSTALLED ACCORDING TO MANUFACTURER'SINSTRUCTIONS AND RECOMMENDATIONS, SO THAT COMPLETED INSTALLATION SHALL OPERATE SAFELYAND EFFICIENTLY.

21. EACH RESPECTIVE CONTRACTOR SHALL FIRE STOP ALL NEW AND EXISTING SLEEVES THROUGHCONCRETE FLOORS AND FIRE RATED WALLS OR PARTITIONS WITH UL RATED ASSEMBLIES WITH EQUALFIRE RATING. FIELD VERIFY EXISTING CONDITIONS BEFORE SUBMITTING PRICE.

22. COORDINATE ROOF PENETRATIONS WITH WORK OF OTHER SECTIONS AND WITH FLASHINGREQUIREMENTS.

23. ANY INTERFERENCE SHALL BE BROUGHT TO THE ATTENTION OF THE OWNER'S REPRESENTATIVE, ANDSHALL BE RESOLVED PRIOR TO THE INSTALLATION OF THE WORK INVOLVED.

24. ALL MATERIALS AND EQUIPMENT SHALL BE NEW UNLESS NOTED OTHERWISE.25. MANUFACTURERS' MODEL NUMBERS ARE SPECIFIED SOLELY TO ESTABLISH STANDARDS OF QUALITY

FOR PERFORMANCE AND MATERIALS.25. SUBSTITUTED PRODUCTS SUBMITTED AND APPROVED FOR USE THAT NECESSITATE CHANGES TO THE

WORK OF THAT OR ANY OTHER TRADES OF CONTRACT SHALL BE COORDINATED AND ARRANGED BY THECONTRACTOR WHO SUBMITTED THE SUBSTITUTION WITHOUT ADDITIONAL COST TO THE OWNER.

26. PRODUCT INSTALLATION SHALL ADHERE TO MANUFACTURERS RECOMMENDATIONS.27. EACH RESPECTIVE CONTRACTOR SHALL PROVIDE PROPER ACCESS TO EQUIPMENT THAT REQUIRES

INSPECTION, REPLACEMENT OR REPAIR. ACCESS PANELS SHALL BE A MINIMUM OF 12" X 12" OR ASNEEDED FOR APPROPRIATE ACCESS. TO BE SUPPLIED TO GENERAL CONTRACTOR FOR INSTALLATION.ACCESS PANELS IN RATED ASSEMBLIES SHALL BE ACUDOR FW-5050. ACCESS PANELS IN NON-RATEDDRYWALL CEILINGS SHALL BE WIND-LOCK "STEALTH". ACCESS PANELS IN NON-RATED WALLS SHALL BEADUDOR UF-5000.

28. CONTRACTOR SHALL COORDINATE ELECTRICAL CHARACTERISTICS AND REQUIREMENTS OF ALLAPPLICABLE EQUIPMENT WITH THE ELECTRICAL CONTRACTOR.

29. ALL EQUIPMENT, PIPING, INSULATION, ETC., INSTALLED IN HVAC PLENUM SPACES SHALL MEET CODEREQUIREMENTS FOR SMOKE AND COMBUSTIBILITY.

30. AS WORK PROGRESSES AND FOR DURATION OF CONTRACT, MAINTAIN COMPLETE SET OF PRINTS OFCONTRACT DRAWINGS AT JOB SITE AT ALL TIMES. RECORD WORK COMPLETED AND ALL CHANGESFROM ORIGINAL CONTRACT DRAWINGS CLEARLY AND ACCURATELY INCLUDING WORK INSTALLED AS AMODIFICATION OR ADDITION TO THE ORIGINAL DESIGN TURN OVER ALL OPERATING MANUALS,MAINTENANCE MANUALS, AND "AS BUILT" DRAWINGS TO OWNER AT CONCLUSION OF CONSTRUCTION.

31. DO NOT SUPPORT EQUIPMENT FROM SUSPENDED CEILINGS. SUPPORT ALL EQUIPMENT AND PIPINGFROM BUILDING. STRUCTURE TO PROVIDE A VIBRATION FREE INSTALLATION. NOTIFY ARCHITECT ANDSTRUCTURAL ENGINEER OF ALL WEIGHTS AND METHODS OF SUPPORT.

32. RUN PIPING/WIRING CONCEALED, UNLESS SPECIFIED OTHERWISE, AND CLEAR OF CEILING INSERTS.33. PROVIDE CLAMPS, OFFSETS, EXPANSION JOINTS, ANCHORS AND GUIDES AS NECESSARY TO PREVENT

STRESS ON PIPING/WIRING. .34. ANY REFERENCE TO ELECTRICAL, PLUMBING AND HVAC CONTRACTORS, NOTED ON THESE DRAWINGS

OR STATED IN THE SPECIFICATIONS SHALL NOT BE MISCONSTRUED AS AN INTENTION TO DEFINESEPARATE CONTRACTORS FOR THE RESPECTIVE WORK. THE GENERAL CONTRACTOR SHALL COORDINATEAND PROVIDE A COMPLETE BUILDING WITH COMPLETE MECHANICAL AND ELECTRICAL SYSTEMS,REGARDLESS OF ANY SPECIFICATION REFERENCES TO OTHER CONTRACTORS.

35. GUARANTEE WORK OF THIS CONTRACTOR IN WRITING FOR ONE YEAR FROM THE DATE OF OWNER'SACCEPTANCE OF CERTIFICATE OF SUBSTANTIAL COMPLETION. PROMPTLY, REPAIR OR REPLACEDEFECTIVE MATERIALS, EQUIPMENT, WORKMANSHIP AND INSTALLATIONS THAT DEVELOP DEFECTSWITHIN THIS PERIOD. PROMPTLY AND TO OWNERS SATISFACTION, CORRECT DAMAGE CAUSED INMAKING NECESSARY REPAIRS AND REPLACEMENTS UNDER GUARANTEED AT NO ADDITIONAL COST TOOWNER. SUBMIT GUARANTEE TO ARCHITECT BEFORE FINAL PAYMENT. STATEMENT OF GUARANTEEREQUIREMENTS SHALL NOT BE INTERRUPTED TO LIMIT OWNER'S RIGHTS UNDER LAW AND THISCONTRACT.

LAVATORY / SINK PIPING DETAILNO SCALE

CAST SETSCREWESCUTCHEON

FLOOR

McGUIRE NO. 8089P-TRAP

COUNTERTOP

ANGLE STOPS

McGUIRE NO 151DRAIN ASSEMBLY

COUNTERTOP

1/2"1/2"

PROVIDE TRUEBROPIPING INSTALLATION

REFRIGERATOR WATER FEED DETAILNO SCALE

CEILING

FLOOR

COORDINATE MOUNTING HEIGHTW/SPECIFIED REFRIGERATOR

CWREFRIGERATOR OUTLET BOX

1/2" CW DNIN WALL

ELECTRIC WATER COOLER W/BOTTLER FILLER

HALSEY TAYLOR STAINLESS STEELHTHB-

HACG8BLSS-WF--- --- PRESS BAR ------

1 1/2" C.B. CAST BRASS W/CLEANOUT PLUG

EWC-1 1/2" SUPPLIES, C.B. ESCUTCHEON STAINLESS STEEL

AS

N

OT

ED

JM

F

DF

(R) LAV

(R) SK (R) SHO

(R) SK

REMOVE EXISTING PLUMBING FIXTURES.EXISTING PIPING TO REMAIN FORINSTALLATION OF NEW FIXTURES.

REMOVE EXISTING PLUMBING FIXTURE.EXISTING PIPING TO REMAIN FORINSTALLATION OF NEW FIXTURE.

REMOVE EXISTING PLUMBING FIXTURES.EXISTING PIPING TO REMAIN FOR

INSTALLATION OF NEW FIXTURES.

REMOVE EXISTING PLUMBING FIXTURES.EXISTING PIPING TO REMAIN FOR

INSTALLATION OF NEW FIXTURES.

REMOVE EXISTING PLUMBING FIXTURE.EXISTING PIPING TO REMAIN FORINSTALLATION OF NEW FIXTURE.

REMOVE EXISTING PLUMBING FIXTURES.EXISTING PIPING TO REMAIN FORINSTALLATION OF NEW FIXTURES.

REMOVE EXISTING PLUMBING FIXTURE.EXISTING PIPING TO REMAIN FORINSTALLATION OF NEW FIXTURE.

(R) WC

(R) UR

(R) LAV (R) LAV(R) UR

(R) UR

(R) WC (R) WC (R) SHO (R) SHO

(R) WC(R) WC

(R) LAV (R) LAV (R) LAV

(R) WC

(R) WC (R) WC

(R) WC

(R) LAV

(R) LAV

(R) LAV

(R) LAV

(R) SK

(R) WC

(R) SK

(R) SK

(R) WC

(R) WC (R) WC (R) WC

(R) UR(R) LAV

(R) LAV

(R) LAV(R) LAV

TOILET ROOM FIXTURESEXISTING TO REMAIN

JANITOR CLOSET FIXTUREEXISTING TO REMAIN

(E) WC (E) LAV

(E) MSB

(R) EWC

KEY PLAN

PHASE 1 PHASE 2

PHASE 3PD-1

1

SCALE - 1/8" = 1'-0"

PLUMBING DEMOLITION FLOOR PLAN

AS

N

OT

ED

JM

F

DF

N

0' 4' 16'8'

LAV-1LAV-1LAV-1UR-1

UR-1

WC-1 WC-1 SHO-1SHO-1

WC-1 WC-1

LAV-1LAV-1LAV-1SK-1

SHO-1

SK-2 WC-1

WC-1

WC-1

LAV-1

LAV-1LAV-1

LAV-1

SK-1

INSTALL NEW FIXTURES.CONNECT TO EXISTING PIPING.MODIFY EXISTING PIPING ASREQUIRED FOR INSTALLATIONOF NEW FIXTURES.

INSTALL NEW FIXTURES.CONNECT TO EXISTING PIPING. MODIFY EXISTING PIPING AS

REQUIRED FOR INSTALLATION OF NEW FIXTURES.CONNECT TO EXISTING CW PIPING AND EXTEND 1/2" CW LINE

TO COFFEE MACHINE & ICE MAKER. TERMINATE CW FEEDSWITH ROB-1 (TYP. FOR 2). SEE ARCH PLANS FOR FINAL

EQUIPMENT LOCATION.

INSTALL NEW FIXTURES.CONNECT TO EXISTING PIPING.

MODIFY EXISTING PIPING ASREQUIRED FOR INSTALLATION

OF NEW FIXTURES.

WC-1

WC-1

UR-1

TOILET ROOM FIXTURESEXISTING TO REMAIN

JANITOR CLOSET FIXTUREEXISTING TO REMAIN

(E) WC (E) LAV

(E) MSB

INSTALL NEW FIXTURES.CONNECT TO EXISTING PIPING.

MODIFY EXISTING PIPING ASREQUIRED FOR INSTALLATION

OF NEW FIXTURES.

EWC

KEY PLAN

PHASE 1

P-1.1

1

SCALE - 1/8" = 1'-0"

PLUMBING FLOOR PLAN - PHASE 1

AS

N

OT

ED

JM

F

DF

0'4' 16'8'

LAV-1LAV-1

LAV-1LAV-1

SK-1

SK-1

WC-1 WC-1 WC-1

WC-1UR-1

WC-1

INSTALL NEW FIXTURES.CONNECT TO EXISTING PIPING.MODIFY EXISTING PIPING ASREQUIRED FOR INSTALLATIONOF NEW FIXTURES.

INSTALL NEW FIXTURE.CONNECT TO EXISTING PIPING. MODIFY EXISTING PIPING AS

REQUIRED FOR INSTALLATION OF NEW FIXTURE.CONNECT TO EXISTING CW PIPING AND EXTEND 1/2" CW LINE

TO COFFEE MACHINE & ICE MAKER. TERMINATE CW FEEDSWITH ROB-1 (TYP. FOR 2). SEE ARCH PLANS FOR FINAL

EQUIPMENT LOCATION.

JANITOR CLOSET FIXTUREEXISTING TO REMAIN

INSTALL NEW FIXTURE.CONNECT TO EXISTING PIPING. MODIFY EXISTING PIPING ASREQUIRED FOR INSTALLATION OF NEW FIXTURE.CONNECT TO EXISTING CW PIPING AND EXTEND 1/2" CW LINETO COFFEE MACHINE & ICE MAKER. TERMINATE CW FEEDSWITH ROB-1 (TYP. FOR 2). SEE ARCH PLANS FOR FINALEQUIPMENT LOCATION.

KEY PLAN

PHASE 2

P-1.2

1

SCALE - 1/8" = 1'-0"

PLUMBING FLOOR PLAN - PHASE 2

AS

N

OT

ED

JM

F

DF

0' 4' 16'8'

NOTE:NO PLUMBING SCOPE IN PHASE 3.

KEY PLAN

PHASE 3P-1.3

1

SCALE - 1/8" = 1'-0"

PLUMBING FLOOR PLAN - PHASE 3

AS

N

OT

ED

JM

F

DF

0' 4' 16'8'

SPRINKLER CRITERIA GPM /SQ.FT.

CONCEALED SPRINKLER2 1/4" MIN.2 3/4" MAX.

COVER PLATE

CEILING

1. THE DRAWINGS AND SPECIFICATIONS INDICATE A PERFORMANCE SPECIFICATION FOR THE FIRE PROTECTION SYSTEM.THE CONTRACTOR IS RESPONSIBLE FOR PROVIDING A COMPLETE AND OPERATING SYSTEM IN COMPLIANCE WITH THEAPPLICABLE NFPA CODES. AWARDED CONTRACTOR IS RESPONSIBLE FOR DETAILED DESIGN AND PREPARATION OFSIGNED AND SEALED ENGINEERING DOCUMENTS FOR REVIEW/APPROVAL FROM THE OWNER'S INSURANCE CARRIERAND LOCAL AUTHORITY HAVING JURISDICTION.

2. PRIOR TO COMMENCING WORK, CONTRACTOR SHALL SUBMIT SPRINKLER SHOP DRAWINGS, HYDRAULICCALCULATIONS AND EQUIPMENT DATA FOR MATERIALS AND EQUIPMENT TO THE ENGINEER FOR REVIEW ANDAPPROVAL. MATERIALS AND EQUIPMENT SHALL NOT BE INSTALLED BEFORE SHOP DRAWINGS ARE REVIEWED ANDAPPROVED. SCHEDULE AT LEAST TEN WORKING DAYS, EXCLUSIVE OF TRANSMITTAL TIME, FOR SUBMITTAL REVIEW.

3. GENERAL NOTES, SYMBOLS LIST AND DETAILS ARE APPLICABLE TO ALL DRAWINGS OF THIS SECTION.4. SPRINKLER PIPE SIZES ARE TO BE CALCULATED HYDRAULICALLY BY THE FIRE PROTECTION CONTRACTOR.5. THE CONTRACTOR SHALL COORDINATE SPRINKLER HEADS AND ASSOCIATED PIPING LOCATIONS WITH THE ARCHITECT

PRIOR TO COMMENCING WORK IN FINISHED AREAS.6. THE CONTRACTOR SHALL COORDINATE SPRINKLER HEAD LOCATIONS WITH LIGHTING LAYOUT, DUCTWORK AND PIPING

AND OTHER TRADES PRIOR TO ROUGH-IN.7. SEISMIC: WHERE REQUIRED SUBMIT WORKING PLANS, REVIEWED, SIGNED AND STAMPED BY A PROFESSIONAL

STRUCTURAL ENGINEER REGISTERED IN THE STATE IN WHICH THE PROJECT IS LOCATED, CERTIFYING THAT THE PLANSMEETS ALL SEISMIC REQUIREMENTS ESTABLISHED BY AUTHORITIES.

8. BEFORE STARTING WORK IN A PARTICULAR AREA OF THE PROJECT, VISIT SITE AND EXAMINE CONDITIONS UNDERWHICH WORK MUST BE PERFORMED INCLUDING PREPARATORY WORK DONE UNDER OTHER SECTIONS OR CONTRACTSBY OWNER. REPORT CONDITIONS THAT MIGHT AFFECT WORK ADVERSELY IN WRITING THROUGH THE CONTRACTOR TOTHE ARCHITECT/ENGINEER. DO NOT PROCEED WITH WORK UNTIL DEFECTS HAVE BEEN CORRECTED AND THECONDITIONS ARE SATISFACTORY. COMMENCEMENT OF WORK SHALL INDICATE ACCEPTANCE OF EXISTING CONDITIONS.

9. ALL SPRINKLER HEADS IN ACOUSTICAL DROP CEILINGS SHALL BE CENTERED IN TILE.

EXISTING(E)

90° ELBOW

SP WET PIPE SPRINKLER SYSTEM

SQ.FT.

SPKR

O/G-1

PSI

WF

TS

FS

GPM

GV

MIN

(N)

FD

NTS

ORDINARY HAZARD - GROUP 1

POUNDS PER SQUARE INCH

SQUARE FOOT

SPRINKLER

WATER FLOW DETECTOR

TAMPER SWITCH

NOT TO SCALE

FLOOR DRAIN

GATE VALVE

MINIMUM

NEW

FLOW SWITCH

GALLONS PER MINUTE

DR

DN

DSS

DWG

COMP

CV

DIPS DOUBLE INTERLOCKED PREACTION SPRINKLER SYSTEM

DRY PIPE SPRINKLER SYSTEM

DRAIN RISER

DOWN

DRAWING

COMPRESSOR

CHECK VALVE

OFFICES

NFPA HAZARDCLASSIFICATION

LIGHT

CEILING3" - 5" BELOW

UPRIGHT SPRINKLER

UPRIGHT DEFLECTOR

SPRINKLERTEMPERATURE

SP

DIRECTION OF FLOW

WET SPRINKLER SYSTEM

POINT OF CONNECTION BETWEEN EXISTING

3-WAY ALARM TEST

DE

DSP

SHUT OFF VALVE

POINT OF CONNECTION BETWEEN

DELUGE SPRINKLER SYSTEM

AND TO BE REMOVED WORK

DRYPIPE SPRINKLER SYSTEM

NEW AND EXISTING WORK

CHECK VALVE

PRESSURE GUAGE

SOLENOID RELEASE VALVE

SYSTEM CONTROL VALVE

PREACTION ALARM HORN WITH FLASHING

DRY PIPE VALVE

PREACTION CONTROL PANEL

BACKFLOW PREVENTER

PREACTION DELUGE VALVE

WATERFLOW DETECTOR

SYMBOL DESCRIPTION

TYCO SERIES TY-B

BASIS OF DESIGN MANUFACTURER& MODEL #

VICTAULIC, VIKING, RELIABLE

ACCEPTABLEMFGR.

PSIG POUNDS PER SQUARE INCH (GAUGE)

QUICK RESPONSE, THERMO-SENSITIVE GLASS BULB SPRAY SPRINKLER, WHITEFINISH. TO BE USED IN ALL AREAS WITH FINISHED CEILINGS

QUICK RESPONSE, THERMO-SENSITIVE GLASS BULB SPRAY SPRINKLER. TO BE USEDIN ALL AREAS WITHOUT FINISHED CEILINGS

TYCO TY-FRBUPRIGHT VICTAULIC, VIKING, RELIABLE

PENDANT

1. PIPE AND FITTINGSA. PIPE SHALL MEET APPLICABLE ANSI OR ASTM STANDARDS AND SHALL HAVE MANUFACTURER'S NAME AND STANDARD

MARKED ON EACH LENGTH. JOINTS SHALL MEET APPLICABLE ANSI OR ASTM STANDARDS. WHERE ANSI OR ASTMSTANDARD DOES NOT EXIST, JOINTS AND FITTINGS SHALL BEAR UL LISTED SYMBOL.

B. SERVICE: LIGHT HAZARD ABOVE GROUND WET-PIPE SPRINKLER (2 1/2" AND BELOW).PIPE MATERIAL: CPVC (CHLORINATED POLYVINYL CHLORIDE), ASTM D1784FITTING MATERIAL: CPVC, ASTM F437 & ASTM F438.PIPE JOINT: SOLVENT CEMENT, ASTM F656 & ASTM F493

C. SERVICE: ORDINARY HAZARD ABOVE GROUND WET-PIPE SPRINKLER (2 1/2" AND BELOW).PIPE MATERIAL: WELDED AND SEAMLESS STEEL PIPE, SCHEDULE 40, ASTM A53.FITTING MATERIAL: MALLEABLE IRON, CLASS 150, ANSI B 16.3PIPE JOINT: THREADED OR VICTAULIC

D. SERVICE: ABOVE GROUND WET-PIPE SPRINKLER (3" AND LARGER".PIPE MATERIAL: WELDED AND SEAMLESS STEEL PIPE, SCHEDULE 40, ASTM A53FITTING MATERIAL: MALLEABLE IRON, CLASS 150, ANSI B16.3.PIPE JOINT: THREADED OR VICTAULIC

2. HANGERS, ANCHORS, CLAMPS, AND INSERTSA. HANGERS SHALL MEET NFPA STANDARDS. PROVIDE ADJUSTABLE SWIVEL RIGHTS FOR PIPING 3" AND SMALLER.

SUPPORT PIPING FROM BUILDING STRUCTURE TO MAINTAIN REQUIRED GRADE AND PITCH OF PIPE LINES, PREVENTVIBRATIONS, SECURE PIPING IN PLACE. SECURE HANGERS TO INSERTS WHERE PRACTICAL. HANGER TODS SHALL HAVEMACHINE THREADS.

B. HANGER RODS SHALL BE CONNECTED TO BEAM CLAMP, UL-APPROVED CONCRETE INSERTS OR PHILIPS OR APPROVEDEQUAL EXPANSION SHIELDS. RAMSET OR POWER DRIVEN INSETS WILL NOT BE ALLOWED.

C. HANGER SPACING SHALL MEET REQUIREMENT OF STATE AND LOCAL CODES. PIPE SUPPORTS, VERTICAL ANDHORIZONTAL, SHALL NOT BEAR ON SLEEVES.

3. SPRINKLER HEADSA. PROVIDE UL-LISTED AND FM APPROVED FUSIBLE LINK SPRAY SPRINKLER HEADSB. HEADS SHALL HAVE ORDINARY DEGREE TEMPERATURE RATINGS.C. SPRINKLER HEADS SHALL BE RELOCATED OR ADDED TO PROVIDE ADEQUATE COVERAGE THROUGHOUT ALL AREAS IN

ACCORDANCE WITH THE REQUIREMENTS OF NFPA 13.D. WHERE SPRINKLER HEADS ARE SUBJECT TO PHYSICAL DAMAGE PROVIDE PROTECTIVE WIRE GUARD.

4. SPRINKLER SYSTEM INSTALLATIONA. WORK SHALL BE NEAT AND RECTILINEAR. PIPING SHALL RUN CONCEALED. WORK SHALL BE PROPERLY AND

EFFECTIVELY PROTECTED AND PIPE OPENING SHALL BE TEMPORARILY CLOSED TO PREVENT CONSTRUCTION ANDDAMAGE BEFORE COMPLETION.

5. CONTINUITY OF SERVICESA. NOTIFY THE "AUTHORITY HAVING JURISDICTION" WHEN SHUTDOWNS OF EXISTING SYSTEMS ARE NECESSARY.

6. TESTSA. TEST SPRINKLER SYSTEM AS REQUIRED IN NFPA CODE, OWNERS INSURANCE CARRIER, AND AGENCIES THAT HAVE

JURISDICTION.B. NOTIFY ARCHITECT AND AGENCIES THAT HAVE JURISDICTION TESTS ARE TO BE MADE. TEST SPRINKLER PIPING AND

MAKE WATERTIGHT BEFORE CONCEALMENT. TEST SHALL BE WITNESSED BY THE INSURANCE UNDERWATERSREPRESENTATIVE, THE MUNICIPAL INSPECTOR AND A REPRESENTATIVE OF THE ARCHITECT.

C. SPRINKLER SYSTEM SHALL BE TESTED TO HYDROSTATIC TEST OF 200 PSI IN ACCORDANCE WITH NFPA REQUIREMENTSD. IF INSPECTION OR TEST SHOWS DEFECTS, SUCH DEFECTIVE WORK OR MATERIAL, SHALL BE REPLACED AND

INSPECTED AND TESTS SHALL BE REPEATED UNTIL WORK IS ACCEPTED. REPAIRS TO PIPING SHALL BE MADE WITHNEW MATERIAL

7. CLEANINGA. CLEAN INSTALLATION THOROUGHLY UPON COMPLETION TO REMOVE GREASE, CUTTINGS, DIRT AND OTHER FOREIGN

MATERIALS. REPAIR STOPPAGES, DISCOLORATION AND DAMAGE THAT RESULT FROM FAILURE TO CLEAN PIPINGPROPERLY WITHIN CONTRACT PRICE.

GENERAL NOTES - FIRE PROTECTION

FIRE PROTECTION NOTES

FIRE PROTECTION ABBREVIATIONS(NOT ALL ABBREVIATIONS ARE NECESSARILY USED ON THIS PROJECT)

FIRE PROTECTION SYMBOLS(NOT ALL SYMBOLS ARE NECESSARILY USED ON THIS PROJECT)

SPRINKLER SYSTEM DESIGN DATA

SPRINKLER SCHEDULE

REMARKSFINISHORIFICEDIAMETER

TEMPERATURERATING

TYPESYMBOL

WHITE

WHITE

1/2"

1/2"

155° F

155° F

155° F0.10 GPM/ 1500 SQ. FT.NFPA 13 LIGHT HAZARD

OCCUPANCY

NO SCALE

CONCEALED SPRINKLER HEADINSTALLATION DETAIL

NO SCALE

UPRIGHT SPRINKLER HEADINSTALLATION DETAIL

1. THE DRAWINGS AND SPECIFICATIONS INDICATE A PERFORMANCE SPECIFICATION FOR THE FIRE PROTECTION AND FIRE ALARM SYSTEMS. AWARDEDCONTRACTORS ARE RESPONSIBLE FOR DETAILED DESIGN AND PREPARATION OF SIGNED AND SEALED ENGINEERING DOCUMENTS FORREVIEW/APPROVAL FROM OWNERS INSURANCE CARRIER AND LOCAL AUTHORITY HAVING JURISDICTION.

2. DRAWINGS ARE DIAGRAMMATIC: THE CONTRACTOR IS RESPONSIBLE FOR PROVIDING ALL COMPONENTS NECESSARY FOR A COMPLETEINSTALLATION. DETERMINE LOCATIONS OF SYSTEMS AND COMPONENTS IN FIELD. COORDINATE WITH ARCHITECTURAL DRAWINGS AND OTHERTRADES.

3. ADDRESS QUESTIONS REGARDING DRAWINGS TO ARCHITECT IN WRITING BEFORE AWARD OF CONTRACT. OTHERWISE, ARCHITECT'SINTERPRETATION OF MEANING AND INTENT OF DRAWINGS SHALL BE FINAL.

4. THE INTENTION IS FOR INSTALLATION OF COMPLETE AND OPERATING SYSTEMS INSTALLED IN ACCORDANCE WITH THE ASSOCIATEDMANUFACTURER'S INSTRUCTIONS. NOT EVERY COMPONENT REQUIRED IS SHOWN. THE CONTRACTOR SHALL INCLUDE ALL COMPONENTS NORMALLYASSOCIATED WITH THE PARTICULAR SYSTEM AND/OR REQUIRED BY THE MANUFACTURER'S INSTALLATION INSTRUCTIONS. THE SYSTEM SHALL BEFULLY COMMISSIONED AND SIGNED OFF BY AN OFFICER OF THE RESPECTIVE CONTRACTOR. PRIOR TO FINAL OWNER ACCEPTANCE TESTING, PROVIDEPERSONNEL TO ASSIST IN 24 HOURS OF ACCEPTANCE TESTING.

5. GIVE NOTICES, FILE PLANS, OBTAIN PERMITS AND LICENSES, PAY FEES AND BACK CHARGES, AND OBTAIN NECESSARY APPROVALS FROMAUTHORITIES THAT HAVE JURISDICTION AS REQUIRED TO PERFORM WORK IN ACCORDANCE WITH ALL LEGAL REQUIREMENTS AND WITH THE DESIGNDOCUMENTS

6. PRIOR TO COMMENCING WORK, CONTRACTOR SHALL SUBMIT SHOP DRAWINGS AND EQUIPMENT DATA FOR MATERIALS AND EQUIPMENT TO THEARCHITECT FOR REVIEW AND APPROVAL. MATERIALS AND EQUIPMENT SHALL NOT BE INSTALLED BEFORE SHOP DRAWINGS ARE REVIEWED ANDAPPROVED. SCHEDULE AT LEAST TEN WORKING DAYS, EXCLUSIVE OF TRANSMITTAL TIME, FOR SUBMITTAL REVIEW SHALL BE ALLOWED.

7. MATERIALS AND EQUIPMENT SHALL BE LISTED BY UNDERWRITERS LABORATORIES (UL) AND APPROVED BY ASME AND AGA FOR INTENDED SERVICE.8. THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES AND PROCEDURES

REQUIRED FOR SAFE EXECUTION AND COMPLETION OF WORK, AND FOR INITIATING, MAINTAINING AND SUPERVISING ALL SAFETY PRECAUTIONS ANDPROGRAMS IN CONNECTION WITH THE WORK.

9. COORDINATE WORK OF THIS SECTION WITH THAT OF OTHER SECTIONS.10. ALL MATERIALS, EQUIPMENT AND METHOD OF INSTALLATION SHALL BE ACCORDANCE WITH THE STANDARDS, REGULATIONS, CODES, ORDINANCES,

AND LAW OF LOCAL, STATE, AND FEDERAL GOVERNMENTS, AND OTHER AUTHORITIES THAT HAVE LAWFUL JURISDICTION.11. IT SHALL BE THE RESPONSIBILITY OF THIS CONTRACTOR TO COORDINATE HIS WORK WITH THAT OF ALL OTHER TRADES, INCLUDING (BUT NOT

LIMITED TO), ELECTRICAL, HVAC, SPRINKLER, PLUMBING, STRUCTURAL AND GENERAL ARCHITECTURE. OFFSETS IN PIPING AND OFFSETS AROUNDOBSTRUCTIONS SHALL BE PROVIDED AT NO ADDITIONAL COST TO THE OWNER.

12. DEVIATION FROM CONTRACT DOCUMENTS, OR PROPOSED SUBSTITUTION OF MATERIALS OR EQUIPMENT FOR THOSE SPECIFIED, SHALL BEREQUESTED IN SEPARATE LETTER, WHETHER DEVIATIONS ARE DUE TO FIELD CONDITIONS, STANDARD SHOP PRACTICE OR OTHER CAUSE.

13. EACH CONTRACTOR IS RESPONSIBLE FOR ITS CUTTING AND PATCHING REQUIRED FOR THE INSTALLATION OF ITS NEW WORK. CUTTING ANDPATCHING SHALL BE COMPLETED IN A NEAT AND WORKMANLIKE MANNER. PATCHING MATERIALS SHALL MATCH EXISTING MATERIALS TO THEGREATEST EXTENT POSSIBLE. PROVIDE TOUCH-UP TO MATCH EXISTING SURROUNDING AREAS OF CUTTING AND PATCHING WORK

14. INTERRUPTIONS TO EXISTING SERVICES AND SYSTEMS SHALL BE AS SHORT AS POSSIBLE AND AT A TIME AND DURATION APPROVED BY THE OWNER.INCLUDE ALL PREMIUM TIME ASSOCIATED WITH INTERRUPTIONS. INTERRUPTIONS SHALL BE SCHEDULED WITH OWNER 48 HOURS IN ADVANCE.

15. CONTRACTOR SHALL COORDINATE ITS RESPECTIVE CEILING MOUNTED EQUIPMENT WITH OTHER TRADE CONTRACTORS PRIOR TO INSTALLATION TOAVOID CONFLICTS.

16. ANY DEMOLITION SHALL BE COORDINATED WITH OWNER, ARCHITECT, G.C. AND ENGINEER. ALL DEBRIS SHALL BE CLEANED UP AND REMOVED FROMTHE SITE BY THE END OF THE DAY. PRIOR TO DISPOSAL OF EQUIPMENT AND MATERIALS, TURN OVER TO THE OWNER ANY REMOVED EQUIPMENT ANDMATERIALS PER OWNERS REQUEST.

17. WORK SHALL BE EXECUTED IN A WORKMANLIKE MANNER AND SHALL PRESENT NEAT, RECTILINEAR APPEARANCE WHEN COMPLETED. MAINTAINMAXIMUM HEAD ROOM AT ALL TIMES. DO NOT RUN PIPES, DUCTS, AND CONDUIT EXPOSED UNLESS SHOWN AND NOTED TO BE EXPOSED ONDRAWINGS. MATERIALS AND EQUIPMENT SHALL BE NEW AND INSTALLED ACCORDING TO MANUFACTURER'S INSTRUCTIONS ANDRECOMMENDATIONS, SO THAT COMPLETED INSTALLATION SHALL OPERATE SAFELY AND EFFICIENTLY.

18. EACH RESPECTIVE CONTRACTOR SHALL FIRE STOP ALL NEW AND EXISTING SLEEVES THROUGH CONCRETE FLOORS AND FIRE RATED WALLS ORPARTITIONS WITH UL RATED ASSEMBLIES WITH EQUAL FIRE RATING. FIELD VERIFY EXISTING CONDITIONS BEFORE SUBMITTING PRICE.

19. COORDINATE ROOF PENETRATIONS WITH WORK OF OTHER SECTIONS AND WITH FLASHING REQUIREMENTS.20. ANY INTERFERENCE SHALL BE BROUGHT TO THE ATTENTION OF THE OWNER'S REPRESENTATIVE, AND SHALL BE RESOLVED PRIOR TO THE

INSTALLATION OF THE WORK INVOLVED.21. ALL MATERIALS AND EQUIPMENT SHALL BE NEW UNLESS NOTED OTHERWISE.22. MANUFACTURERS' MODEL NUMBERS ARE SPECIFIED SOLELY TO ESTABLISH STANDARDS OF QUALITY FOR PERFORMANCE AND MATERIALS.23. SUBSTITUTED PRODUCTS SUBMITTED AND APPROVED FOR USE THAT NECESSITATE CHANGES TO THE SAID CONTRACTOR'S WORK OR THE WORK OF

OTHER TRADES OF CONTRACT SHALL BE COORDINATED AND ARRANGED BY THE CONTRACTOR WHO SUBMITTED THE SUBSTITUTION WITHOUTADDITIONAL COST TO THE OWNER.

24. PRODUCT INSTALLATION SHALL ADHERE TO MANUFACTURERS RECOMMENDATIONS25. EACH RESPECTIVE CONTRACTOR SHALL PROVIDE PROPER ACCESS TO EQUIPMENT THAT REQUIRES INSPECTION, REPLACEMENT OR REPAIR. ACCESS

PANELS SHALL BE A MINIMUM OF 12" X 12" OR AS NEEDED FOR APPROPRIATE ACCESS. TO BE SUPPLIED TO GENERAL CONTRACTOR FORINSTALLATION. ACCESS PANELS IN RATED ASSEMBLIES SHALL BE ACUDOR FW-5050. ACCESS PANELS IN NON-RATED DRYWALL CEILINGS SHALL BEWIND-LOCK "STEALTH". ACCESS PANELS IN NON-RATED WALLS SHALL BE ADUDOR UF-5000.

26. CONTRACTOR SHALL COORDINATE ELECTRICAL CHARACTERISTICS AND REQUIREMENTS OF ALL APPLICABLE EQUIPMENT WITH THE ELECTRICALCONTRACTOR.

27. ALL EQUIPMENT, PIPING, INSULATION, ETC., INSTALLED IN HVAC PLENUM SPACES SHALL MEET CODE REQUIREMENTS FOR SMOKE ANDCOMBUSTIBILITY.

28. AS WORK PROGRESSES AND FOR DURATION OF CONTRACT, MAINTAIN COMPLETE SET OF PRINTS OF CONTRACT DRAWINGS AT JOB SITE AT ALLTIMES. RECORD WORK COMPLETED AND ALL CHANGES FROM ORIGINAL CONTRACT DRAWINGS CLEARLY AND ACCURATELY INCLUDING WORKINSTALLED AS A MODIFICATION OR ADDITION TO THE ORIGINAL DESIGN TURN OVER ALL OPERATING MANUALS, MAINTENANCE MANUALS, AND "ASBUILT" DRAWINGS TO OWNER AT CONCLUSION OF CONSTRUCTION.

29. DO NOT SUPPORT EQUIPMENT FROM SUSPENDED CEILINGS. SUPPORT ALL EQUIPMENT AND PIPING FROM BUILDING. STRUCTURE TO PROVIDE AVIBRATION FREE INSTALLATION. NOTIFY ARCHITECT AND STRUCTURAL ENGINEER OF ALL WEIGHTS AND METHODS OF SUPPORT.

30. RUN PIPING/WIRING CONCEALED, UNLESS SPECIFIED OTHERWISE, AND CLEAR OF CEILING INSERTS.31. PROVIDE CLAMPS, OFFSETS, EXPANSION JOINTS, ANCHORS AND GUIDES AS NECESSARY TO PREVENT STRESS ON PIPING/WIRING. .32. ANY REFERENCE TO ELECTRICAL, PLUMBING AND HVAC CONTRACTORS, NOTED ON THESE DRAWINGS OR STATED IN THE SPECIFICATIONS SHALL NOT

BE MISCONSTRUED AS AN INTENTION TO DEFINE SEPARATE CONTRACTORS FOR THE RESPECTIVE WORK. THE GENERAL CONTRACTOR SHALLCOORDINATE AND PROVIDE A COMPLETE BUILDING WITH COMPLETE MECHANICAL AND ELECTRICAL SYSTEMS, REGARDLESS OF ANY SPECIFICATIONREFERENCES TO OTHER CONTRACTORS.

33. GUARANTEE WORK OF THIS CONTRACTOR IN WRITING FOR ONE YEAR FROM THE DATE OF OWNER'S ACCEPTANCE OF CERTIFICATE OF SUBSTANTIALCOMPLETION. PROMPTLY, REPAIR OR REPLACE DEFECTIVE MATERIALS, EQUIPMENT, WORKMANSHIP AND INSTALLATIONS THAT DEVELOP DEFECTSWITHIN THIS PERIOD. PROMPTLY AND TO OWNERS SATISFACTION, CORRECT DAMAGE CAUSED IN MAKING NECESSARY REPAIRS ANDREPLACEMENTS UNDER GUARANTEED AT NO ADDITIONAL COST TO OWNER. SUBMIT GUARANTEE TO ARCHITECT BEFORE FINAL PAYMENT.STATEMENT OF GUARANTEE REQUIREMENTS SHALL NOT BE INTERRUPTED TO LIMIT OWNER'S RIGHTS UNDER LAW AND THIS CONTRACT.

BUILDING CODE: 2015 INTERNATIONAL BUILDING CODEMECHANICAL CODE: 2015 INTERNATIONAL MECHANICAL CODEPLUMBING CODE: 2015 INTERNATIONAL PLUMBING CODEFUEL GAS CODE: 2015 INTERNATIONAL FUEL GAS CODEELECTRICAL CODE: 2014 NATIONAL ELECTRICAL CODEFIRE CODE: 2015 INTERNATIONAL FIRE CODEENERGY CODE: 2015 INTERNATIONAL ENERGY CONSERVATION CODE

MUNICIPALITY

USE AND OCC. CLASSIFICATION

APPLICABLE CODES

BUSINESS GROUP B

TREDYFFRIN TOWNSHIP, PA

CODE SUMMARY

GENERAL SPECIFICATIONS

EXISTING SPRINKLER SYSTEM.NFPA 13 LIGHT HAZARD CLASSIFICATION.

0.10 GPM/ 1500 SQ.FT.CONNECTED TO EXISTING SPRINKLER SERVICE.

INTERFACE WITH BUILDING FIRE ALARM SYSTEM.TURN DOWN/ REWORK SPRINKLER HEADS ASREQUIRED TO SATISFY SPACE CONDITIONS &

CEILING MODIFICATIONS.

KEY PLAN

PHASE 1

FP-1.1

1

SCALE - 1/8" = 1'-0"

FIRE PROTECTION FLOOR PLAN - PHASE 1

AS

N

OT

ED

JM

F

DF

0'4' 16'8'

EXISTING SPRINKLER SYSTEM.NFPA 13 LIGHT HAZARD CLASSIFICATION.

0.10 GPM/ 1500 SQ.FT.CONNECTED TO EXISTING SPRINKLER SERVICE.

INTERFACE WITH BUILDING FIRE ALARM SYSTEM.TURN DOWN/ REWORK SPRINKLER HEADS ASREQUIRED TO SATISFY SPACE CONDITIONS &

CEILING MODIFICATIONS.

KEY PLAN

PHASE 2

FP-1.2

1

SCALE - 1/8" = 1'-0"

FIRE PROTECTION FLOOR PLAN - PHASE 2

AS

N

OT

ED

JM

F

DF

0'4' 16'8'

NOTE:NO FIRE PROTECTION SCOPE INPHASE 3.EXISTING FIRE PROTECTIONSYSTEM TO REMAIN.

KEY PLAN

PHASE 3FP-1.3

1

SCALE - 1/8" = 1'-0"

FIRE PROTECTION FLOOR PLAN - PHASE 3

AS

N

OT

ED

JM

F

DF

0' 4' 16'8'

VOICE COMMUNICATION OUTLET

CEILING MOUNTED JUNCTION BOX

MOTOR OR MOTORIZED EQUIPMENT. NUMBER INDICATESHORSEPOWER (HP)

DISCONNECT SWITCH, SIZE AS INDICATED ON PLAN

JB

A

FUSED DISCONNECT SWITCH, SIZE AS INDICATED ON PLAN

LOCKING OR NONLOCKING NEMA RECEPTACLE ASNOTED

MS

TV CABLE TV OUTLET

RECESSED DOWNLIGHT, "A" INDICATES TYPE, "2"INDICATES CIRCUIT BREAKER POSITION, "a" INDICATESSWITCHING

2 a

WALL MOUNTED LIGHT FIXTURE, "A" INDICATES TYPE, "2"INDICATES CIRCUIT BREAKER POSITION, "a" INDICATESSWITCH CONTROL

A

2 a

A

2 aCEILING OR WALL MOUNTED LINEAR LED LIGHT FIXTURE,"A" INDICATES TYPE, "2" INDICATES CIRCUIT BREAKERPOSITION, "a" INDICATES SWITCH CONTROL

CEILING OR WALL MOUNTED INDUSTRIAL LED STRIPLIGHT FIXTURE, "A" INDICATES TYPE, "2" INDICATESCIRCUIT BREAKER POSITION, "a" INDICATES SWITCHCONTROL

A

2 a

CEILING OR WALL MOUNTED SINGLE FACE EXIT SIGN, "X"INDICATES TYPE, ARROWS AS INDICATED ON PLANS.CONNECT TO LOCAL LIGHTING BRANCH CIRCUIT AHEADOF ALL SWITCHING UNLESS OTHERWISE NOTED

X X

WALL MOUNTED EMERGENCY BATTERY PACK WITH(2)-LIGHT HEADS, "EM" INDICATES TYPE. CONNECT TOLOCAL LIGHTING BRANCH CIRCUIT AHEAD OF ALLSWITCHING UNLESS OTHERWISE NOTED

2#12 & 1#12GND. IN 3/4" CONDUIT CONCEALED INWALL OR CEILING UNLESS OTHERWISE NOTED

125V., 20A SIMPLEX RECEPTACLE MOUNTED AT 18" AFFUNLESS OTHERWISE NOTED

125V., 20A DUPLEX RECEPTACLE MOUNTED AT 18" AFFUNLESS OTHERWISE NOTED. ALL DWELLING UNITRECEPTACLES SHALL BE TAMPER RESISTANT INACCORDANCE WITH NEC ART.406.11."+" INDICATESMOUNTED AT 42" AFF OR 6" ABOVE COUNTER ORBACKSPLASH

WP

+

125V., 20A DUPLEX GFCI RECEPTACLE MOUNTED AT 18"AFF UNLESS OTHERWISE NOTED. "+" INDICATESMOUNTED AT 42" AFF OR 6" ABOVE COUNTER ORBACKSPLASH. "WP" INDICATES WEATHERPROOFENCLOSURE

+

125V., 20A DOUBLE DUPLEX RECEPTACLE MOUNTED AT18" AFF UNLESS OTHERWISE NOTED.

125V., 20A DUPLEX RECEPTACLE WITH BOTTOMRECEPTACLE CONNECTED TO WALL SWITCH, MOUNTEDAT 18" AFF UNLESS OTHERWISE NOTED. "+" INDICATESMOUNTED AT 42" AFF OR 6" ABOVE COUNTER ORBACKSPLASH

JB

125V., 20A TOGGLE SWITCH MOUNTED AT 42" AFFUNLESS OTHERWISE NOTED.

125V., 20A DOOR JAMB SWITCH MOUNTED AT 42" AFFUNLESS OTHERWISE NOTED.

125V., 20A CEILING FAN SPEED SWITCH MOUNTED AT42" AFF UNLESS OTHERWISE NOTED.

125V., 20A 3-WAY TOGGLE SWITCH MOUNTED AT 42"AFF UNLESS OTHERWISE NOTED.

125V., 20A BATHROOM EXHAUST FAN TIMER SWITCHMOUNTED AT 42" AFF UNLESS OTHERWISE NOTED.

125V., 20A MOTOR RATED SWITCH MOUNTED AT 42"AFF UNLESS OTHERWISE NOTED.

IC

B

INTERCOM STATION

DOOR BELL/INTERCOM STATION

J

OS

DATA COMMUNICATION OUTLET

VOICE & DATA COMMUNICATION OUTLET

5

WALL MOUNTED JUNCTION BOX

MOTOR STARTER, SIZE AS INDICATED ON PLAN

2'X4' RECESSED LED FIXTURE, "A" INDICATES TYPE, "2"INDICATES CIRCUIT BREAKER POSITION, "a" INDICATESSWITCHING

2'X4' RECESSED LED FIXTURE CONNECTED TOEMERGENCY (EM) AND/OR NIGHT LIGHT (NL) CIRCUIT,"A" INDICATES TYPE, "2" INDICATES CIRCUIT BREAKERPOSITION, "a" INDICATES SWITCHING

A

2 a

A

2 a

2'X2' RECESSED LED FIXTURE, "A" INDICATES TYPE, "2"INDICATES CIRCUIT BREAKER POSITION, "a" INDICATESSWITCHING

2'X2' RECESSED LED FIXTURE CONNECTED TOEMERGENCY (EM) AND/OR NIGHT LIGHT (NL) CIRCUIT,"A" INDICATES TYPE, "2" INDICATES CIRCUIT BREAKERPOSITION, "a" INDICATES SWITCHING

A

2

A

2

a

a

CEILING OR WALL MOUNTED EXIT SIGN WITH INTEGRALEMERGENCY LIGHT HEADS, "X" INDICATES TYPE,ARROWS AS INDICATED ON PLANS. CONNECT TO LOCALLIGHTING BRANCH CIRCUIT AHEAD OF ALL SWITCHINGUNLESS OTHERWISE NOTED

EM

WALL OR CEILING MOUNTED TWIN REMOTE EMERGENCYLIGHT "EM" INDICATES TYPE, "WP" INDICATESWEATHERPROOF.

WALL MOUNTED DUAL TECHNOLOGY OCCUPANCYSENSOR

CEILING MOUNTED DUAL TECHNOLOGY OCCUPANCYSENSOR

PENDANT MOUNTED LIGHT FIXTURE, "A" INDICATESTYPE, "2" INDICATES CIRCUIT BREAKER POSITION, "a"INDICATES SWITCHING

2#12 & 1#12GND. IN 3/4" CONDUIT, UNLESSOTHERWISE NOTED, HOME RUN TO PANEL, "P1"INDICATES PANEL NAME, "3" INDICATES CIRCUITBREAKER POSITION

P1-3

PLAN NOTE CALLOUT

A

2

M METER AND SOCKET

POWER OPERATED DOOR SYSTEM

NEW CONNECTION TO EXISTING

TERMINATION OF DEMOLITION

RECESSED WALLWASHER DOWNLIGHT, "A" INDICATESTYPE, "2" INDICATES CIRCUIT BREAKER POSITION, "a"INDICATES SWITCHING

A

2 a

CEILING MOUNTED PADDLE FAN, "A" INDICATES TYPE,"2" INDICATES CIRCUIT BREAKER POSITION

CEILING OR WALL MOUNTED DOUBLE FACE EXIT SIGN,"X" INDICATES TYPE, ARROWS AS INDICATED ON PLANS.CONNECT TO LOCAL LIGHTING BRANCH CIRCUIT AHEADOF ALL SWITCHING UNLESS OTHERWISE NOTED COMBINATION POWER/DATA FLOOR FLUSH MOUNTED

BOX OR POKE-THRU DEVICE, REFER TO PLANS FOR TYPEAND DEVICE CONFIGURATION

A

2 a

2#12 & 1#12GND. IN 3/4" CONDUIT RUN IN OR UNDERCONCRETE SLAB UNLESS OTHERWISE NOTED

2#12 & 1#12GND. IN 3/4" CONDUIT RUN EXPOSEDUNLESS OTHERWISE NOTED

DRAWOUT CIRCUIT BREAKER MEDIUM VOLTAGE

DRAWOUT CIRCUIT BREAKER

FUSE

GROUND CONNECTION

E ELECTRIC INTERLOCK SWITCH

MOLDED CASE CIRCUIT BREAKER

J JUNCTION OR PULL BOX. SIZE AS INDICATED ON PLAN

PANEL"P1"

FUSED SWITCH

COMBINATION MOTOR STARTER AND DISCONNECTSWITCH, SIZE AS INDICATED ON PLAN

PANELBOARD, SIZE, TYPE AND RATING AS INDICATED ONPLAN

PANELBOARD, SURFACE MOUNTED

PANELBOARD, FLUSH MOUNTED

T

COPPER GROUND BAR, SIZE AS INDICATED ON PLAN

TRANSFORMER, SIZE, TYPE AND RATING AS INDICATEDON PLAN

G COPPER GROUND CONDUCTOR, SIZE AS INDICATED ONPLAN

WARNING AND SIGNALING FIXTURES/SIGNS.

WALL-MOUNTED CLOCKS, PROGRAM BELLS,FIRE ALARM AUDIBLE AND VISUAL DEVICES(OR AS SHOWN ON ARCHITECTURAL DETAILS)

EXIT SIGNS, BATTERY UNITS ANDEMERGENCY REMOTE HEADS (OR 6" BELOWFINISHED CEILING TO TOP OF FIXTURE)

TOP OF FLUSH AND SURFACE MOUNTEDELECTRICAL PANELBOARDS, TELEPHONECABINETS, OR FIRE ALARM CABINETS.

TOP OF BACK-MOUNTED WALL EXITFIXTURES (NOT MOUNTED ABOVE DOORS)

TOP OF HIGHEST ELECTRICAL SAFETYDISCONNECT SWITCHES, MAGNETICSTARTERS, CONTACTORS.

WALL MOUNTED TELEPHONES AND PAYSTATIONS, THERMOSTATS (3'-6" ATHANDICAP LOCATIONS).

WALL MOUNTED ELECTRICAL LIGHT SWITCHES,MANUAL MOTOR STARTERS, FIRE ALARM PULLSTATIONS, AND WALL MOUNTED WIREMOLD. OBTAINMOUNTING HEIGHT APPROVAL FROM BUILDINGINSPECTOR PRIOR TO ROUGHING IN LIGHT SWITCHES.

ELECTRICAL RECEPTACLE WITHINELECTRICAL/MECHANICAL SPACES ANDELEVATOR ROOMS.

FINISHED FLOOR

NO SCALE

6'-6"

6'-3"

6'-0"

4'-6"

3'-6"

2'-0"

1'-6"

10'-0"

PER N.F.P.A. &A.D.A. CODE

REQUIREMENTS

CENTEREDABOVE DOOR OR

WINDOWOPENING

ELECTRICAL RECEPTACLES, TELEPHONEOUTLETS, COMPUTER OUTLETS UNLESS INWIREMOLD, OR OTHERWISE NOTED.

0'-8" BOTTOM OF EXIT SIGN ADJACENT TO DOOR(WHERE REQUIRED)

ADA UNIT INTERCOM. CENTEROF "CALL" BUTTON.

3'-0"

TYPICAL STANDARD MOUNTING HEIGHTSDETAIL

NOTES:1. MOUNTING HEIGHTS TO CENTER OF OUTLETS UNLESS OTHERWISE

NOTED. IN MASONRY WALL CONSTRUCTION THE ABOVE MOUNTINGHEIGHTS SHALL BE USED FOR REFERENCE TO NEAREST BLOCK ORBRICK COURSING.

2. THE ABOVE MOUNTING HEIGHTS SHALL BE ADHERED TO UNLESSSPECIFICALLY NOTED OR DETAILED OTHERWISE ON THE DRAWINGSOR SPECIFICATIONS.

1

SJ

SF

S3

ST

SOS

S

ELEVATOR CONTROLLER. REFER TO "ELEVATOR CONTROLSWITCH" NOTE ON THIS PLAN FOR ADDITIONALINFORMATION

EC

SWITCHES, COVERPLATES AND RECEPTACLES BASIS OF DESIGN:COMMERCIAL - DEVICES SHALL BE WHITE WITH A METAL STAINLESS STEEL COVERPLATERESIDENTIAL-DEVICE COLOR BY ARCHITECT WITH A MATCHING COVERPLATE

CEILING MOUNTED 125V., 20A DOUBLE DUPLEXRECEPTACLE.

CEILING MOUNTED 125V., 20A DUPLEX RECEPTACLE

ELECTRICAL SYMBOLS

MTD.

P.C.

P.S.

PLG

SLD

SP/ST

S/S

R.T.U.

N.L.

SW.

UH

T/C

VAV

XFMR.

WP

V

(E)

(RL)

(R)

MOD MOTOR OPERATED DOOR

ELECTRIC WATER COOLEREWC

ELECTRIC WALL HEATEREWH

ABOVE

AMPS

ABOVE FINISHED FLOOR

CABINET HEATER

CIRCUIT BREAKER

AIR HANDLER UNIT

CEILING

ABOVE FINISHED GRADE

DRAWING

DUAL ELEMENT (TIME DELAY)

EXHAUST FAN

ELECTRICAL CONTRACTOR

ELECTRIC BASEBOARD HEATER

ELECTRIC UNIT HEATER

EMERGENCY POWER-OFF

INDICATES LIGHT FIXTURE WIREDTO EMERGENCY CIRCUIT

A.H.U.

DWG

E.P.O.

EUH

EM

E.B.H.

E.C.

E.F.

D.E.

C.H.

CLG.

C/B

A.F.F.

A.F.G.

ABV.

A

J.B.

MECH.

MLO

MCB

M.C.

KW

KVA

HWH

IG

HVAC

GND.

HP

HTR.

G.F.I.

JUNCTION BOX

MECHANICAL CONTRACTOR

MAIN LUGS ONLY

MAIN CIRCUIT BREAKER

MECHANICAL

KILOVOLT-AMPERE

KILOWATT

HEATING, VENTILATING,

HOT WATER HEATER

ISOLATED GROUND

HEATER

HORSE POWER

GROUND FAULT INTERRUPT

GROUND

FU.

G.C.

FACP

EXIST.

FIRE ALARM CONTROL PANEL

GENERAL CONTRACTOR

FUSE (OR FUSED)

EXISTING

PLUMBING CONTRACTOR

UNIT HEATER

VARIABLE AIR VOLUME

REMOVE EXISTING

RELOCATED EXISTING

EXISTING TO REMAIN

WEATHERPROOF

TRANSFORMER

VOLTS

SINGLE POLE/SINGLE THROW

SINGLE LINE DIAGRAM

SAFETY SWITCH

TIME CLOCK

SWITCH

PAY STATION

ROOF TOP UNIT

PLUMBING

NIGHT LIGHTING

MOUNTED

UNLESS OTHERWISE NOTEDU.O.N.

FATB FIRE ALARM TERMINAL BOX

FSD FIRE SMOKE DAMPER

(DISCONNECT SWITCH)

PUSHBUTTON SWITCH

& AIR CONDITIONING

ABBREVIATIONS

CEILING MOUNTED 125V., COMBINATION SMOKEDETECTOR/HORN-STROBE

CARBON MONOXIDE DETECTOR,CEILING MOUNTED 125V

F

H

S FIRE ALARM SMOKE DETECTOR

FIRE ALARM DUCT SMOKE DETECTOR

FIRE ALARM HEAT DETECTOR

FIRE ALARM SPEAKER

FIRE ALARM PULL STATION

FIRE ALARM STROBE

FIRE ALARM HORN/STROBE

FIRE ALARM WATER FLOW SWITCH

FIRE ALARM TAMPER SWITCH

S

WF

TS

S

S

F

F

FIRE ALARM ADDRESSABLE INPUT MODULEAM

CM FIRE ALARM ADDRESSABLE CONTROL MODULE

CO

FIRE ALARM DOOR HOLD OPEN DEVICEDH

VOICE COMMUNICATION OUTLET

TV CABLE TV OUTLET

IC

DC

DOOR INTERCOM STATION

DOOR CONTROLLER

DATA COMMUNICATION OUTLET

VOICE & DATA COMMUNICATION OUTLET

MC

CR

FURNITURE FEED

CARD READER

WIRELESS RADIO LINK

WIRELESS RADIO LINK

JJ

DP FURNITURE WHIP AND FEED (COORDINATE REQUIREMENTS)

P = POWERD = DATA

GENERAL SPECIFICATIONS

1. DRAWINGS ARE DIAGRAMMATIC: THE CONTRACTOR IS RESPONSIBLE FOR PROVIDING ALL COMPONENTSNECESSARY FOR A COMPLETE AND OPERATIONAL SYSTEM. COORDINATE AND DETERMINE FINALLOCATIONS OF SYSTEMS AND COMPONENTS IN FIELD. COORDINATE WITH ARCHITECTURAL DRAWINGSAND OTHER TRADES.

2. ADDRESS ALL QUESTIONS REGARDING DRAWINGS TO ARCHITECT IN WRITING BEFORE SUBMITTING BIDPROPOSAL. OTHERWISE, ARCHITECT'S INTERPRETATION OF MEANING AND INTENT OF DRAWINGS SHALLBE FINAL.

3. THE INTENTION IS FOR INSTALLATION OF COMPLETE AND OPERATING SYSTEMS. NOT EVERYCOMPONENT REQUIRED IS SHOWN. THE CONTRACTOR SHALL INCLUDE ALL COMPONENTS NORMALLYASSOCIATED WITH THE PARTICULAR SYSTEM. THE SYSTEM SHALL BE FULLY COMMISSIONED ANDSIGNED OFF BY AN OFFICER OF THE RESPECTIVE CONTRACTOR PRIOR TO FINAL OWNER ACCEPTANCETESTING. PROVIDE PERSONNEL TO ASSIST WITH OWNER ACCEPTANCE TESTING.

4. GIVE NOTICES, FILE PLANS, OBTAIN PERMITS AND LICENSES, PAY FEES AND BACK CHARGES, ANDOBTAIN NECESSARY APPROVALS FROM AUTHORITIES THAT HAVE JURISDICTION AS REQUIRED TOPERFORM WORK IN ACCORDANCE WITH ALL LEGAL REQUIREMENTS AND WITH THE DESIGN DOCUMENTS.

5. PRIOR TO COMMENCING WORK, CONTRACTOR SHALL SUBMIT SHOP DRAWINGS AND EQUIPMENT DATAFOR MATERIALS AND EQUIPMENT TO THE ARCHITECT FOR REVIEW AND APPROVAL. MATERIALS ANDEQUIPMENT SHALL NOT BE INSTALLED BEFORE SHOP DRAWINGS ARE REVIEWED AND APPROVED. ATLEAST TEN (10) WORKING DAYS, EXCLUSIVE OF TRANSMITTAL TIME, SHALL BE ALLOWED FORSUBMITTAL REVIEW.

6. MATERIALS AND EQUIPMENT SHALL BE LISTED BY UNDERWRITERS LABORATORIES (UL) AND APPROVEDBY ASME AND AGA, AS APPLICABLE, FOR INTENDED SERVICE.

7. THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR CONSTRUCTION MEANS, METHODS,TECHNIQUES, SEQUENCES AND PROCEDURES REQUIRED FOR SAFE EXECUTION AND COMPLETION OFTHE WORK AND FOR INITIATING, MAINTAINING AND SUPERVISING ALL SAFETY PRECAUTIONS ANDPROGRAMS IN CONNECTION WITH THE WORK.

8. ALL MATERIALS, EQUIPMENT AND METHOD OF INSTALLATION SHALL BE ACCORDANCE WITH THESTANDARDS, REGULATIONS, CODES, ORDINANCES AND LAW OF LOCAL, STATE AND FEDERALGOVERNMENTS AND OTHER AUTHORITIES THAT HAVE LAWFUL JURISDICTION.

9. IT SHALL BE THE RESPONSIBILITY OF THIS CONTRACTOR TO COORDINATE THE WORK UNDER THISCONTRACT WITH THAT OF ALL OTHER TRADES, INCLUDING, BUT NOT LIMITED TO, ELECTRICAL, HVAC,SPRINKLER, PLUMBING, STRUCTURAL AND GENERAL CONSTRUCTION. OFFSETS IN DUCTWORK,PIPINGAND CONDUITS AROUND OBSTRUCTIONS SHALL BE PROVIDED AT NO ADDITIONAL COST TO THEOWNER.

10. DEVIATION FROM CONTRACT DOCUMENTS, OR PROPOSED SUBSTITUTION OF MATERIALS OR EQUIPMENTFOR THOSE SPECIFIED, SHALL BE REQUESTED IN SEPARATE LETTER, WHETHER DEVIATIONS ARE DUE TOFIELD CONDITIONS, STANDARD SHOP PRACTICE OR OTHER CAUSE. THE CONTRACTOR IS RESPONSIBLEFOR ANY COSTS INCURRED AS A RESULT OF THE CHANGES NEEDED TO ACCOMMODATE THESUBSTITUTED EQUIPMENT, INCLUDING THE WORK OF OTHER TRADES.

11. EACH CONTRACTOR IS RESPONSIBLE FOR CUTTING AND PATCHING REQUIRED FOR THE INSTALLATION OFNEW WORK UNDER THIS CONTRACT. CUTTING AND PATCHING SHALL BE COMPLETED IN A NEAT ANDWORKMANLIKE MANNER. PATCHING MATERIALS SHALL MATCH EXISTING MATERIALS TO THE GREATESTEXTENT POSSIBLE. PROVIDE TOUCH-UP TO MATCH EXISTING SURROUNDING AREAS OF CUTTING ANDPATCHING WORK.

12. INTERRUPTIONS TO EXISTING SERVICES AND SYSTEMS SHALL BE AS SHORT AS POSSIBLE AND AT ATIME AND DURATION APPROVED BY THE OWNER. INCLUDE ALL PREMIUM TIME ASSOCIATED WITHINTERRUPTIONS IN BID PROPOSAL. INTERRUPTIONS SHALL BE SCHEDULED WITH OWNER AT LEAST 48HOURS IN ADVANCE.

13. CONTRACTOR SHALL COORDINATE ITS RESPECTIVE CEILING MOUNTED EQUIPMENT AND DEVICES WITHOTHER TRADE CONTRACTORS PRIOR TO INSTALLATION TO AVOID CONFLICTS.

14. ALL DEMOLITION WORK SHALL BE COORDINATED WITH OWNER'S REPRESENTATIVE, ARCHITECT,ENGINEER AND GENERAL CONTRACTOR. ALL DEBRIS SHALL BE CLEANED AND REMOVED FROM THE SITEBY END OF EACH WORK DAY. PRIOR TO DISPOSAL OF EQUIPMENT AND MATERIALS, TURN OVER TO THEOWNER ANY REMOVED EQUIPMENT AND MATERIALS REQUESTED BY THE OWNER.

15. WORK SHALL BE EXECUTED IN A WORKMANLIKE MANNER AND SHALL PRESENT A NEAT, RECTILINEARAPPEARANCE WHEN COMPLETED.

16. MAINTAIN MAXIMUM HEAD ROOM AT ALL TIMES. DO NOT RUN PIPES, DUCTS AND CONDUIT EXPOSEDUNLESS SHOWN AND NOTED TO BE EXPOSED ON DRAWINGS.

17. MATERIALS AND EQUIPMENT SHALL BE NEW, UNLESS NOTED OTHERWISE, AND INSTALLED ACCORDINGTO MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS SO THAT COMPLETED INSTALLATIONSHALL OPERATE SAFELY AND EFFICIENTLY.

18. EACH RESPECTIVE CONTRACTOR SHALL FIRE STOP ALL NEW AND EXISTING OPENINGS THROUGH FIRERATED FLOORS, WALLS AND CEILINGS WITH UL ASSEMBLIES OF EQUAL RATING. FIELD VERIFY EXISTINGCONDITIONS BEFORE SUBMITTING BID PROPOSAL.

19. COORDINATE ALL ROOF PENETRATIONS WITH WORK OF OTHER TRADES. ALL PENETRATIONS SHALL BESEALED WATERTIGHT. COORDINATE FLASHING REQUIREMENTS TO MAINTAIN ROOF WARRANTY.

20. ANY INTERFERENCE SHALL BE BROUGHT TO THE ATTENTION OF THE OWNER'S REPRESENTATIVE ORARCHITECT AND SHALL BE RESOLVED PRIOR TO THE INSTALLATION OF THE WORK INVOLVED.

21. MANUFACTURERS' MODEL NUMBERS ARE SPECIFIED SOLELY TO ESTABLISH STANDARDS OF QUALITYFOR PERFORMANCE AND MATERIALS.

22. SUBSTITUTED PRODUCTS SUBMITTED AND APPROVED FOR USE THAT NECESSITATE CHANGES TO THEWORK OF OTHER TRADES OF CONTRACT SHALL BE COORDINATED AND ARRANGED BY THE CONTRACTORWHO SUBMITTED THE SUBSTITUTION WITHOUT ADDITIONAL COST TO THE OWNER.

23. PRODUCT INSTALLATION SHALL ADHERE TO MANUFACTURER'S RECOMMENDATIONS AND INSTRUCTION.24. EACH RESPECTIVE CONTRACTOR SHALL PROVIDE PROPER ACCESS TO EQUIPMENT AND COMPONENTS

THAT REQUIRE INSPECTION, MAINTENANCE AND POSSIBLE REPAIR. ACCESS PANELS SHALL BE MINIMUM12"X12" OR AS NEEDED FOR PROPER ACCESS. ACCESS PANELS SHALL BE FURNISHED BY THISCONTRACTOR AND TURNED OVER TO GENERAL CONTRACTOR FOR INSTALLATION.

25. CONTRACTOR SHALL COORDINATE ELECTRICAL CHARACTERISTICS AND REQUIREMENTS OF ALLAPPLICABLE EQUIPMENT WITH THE ELECTRICAL CONTRACTOR.

26. AS WORK PROGRESSES AND FOR DURATION OF CONSTRUCTION, MAINTAIN A COMPLETE SET OFCONTRACT DRAWINGS AT THE JOBSITE. RECORD WORK COMPLETED AND ALL CHANGES FROM ORIGINALCONTRACT DRAWINGS CLEARLY AND ACCURATELY INCLUDING WORK INSTALLED AS A MODIFICATIONOR ADDITION TO THE ORIGINAL DESIGN TURN OVER ALL OPERATING MANUALS, MAINTENANCEMANUALS, AND "AS BUILT" DRAWINGS TO OWNER AT CONCLUSION OF CONSTRUCTION.

27. DO NOT SUPPORT EQUIPMENT, DUCTWORK, PIPING, CONDUIT OR DEVICES FROM SUSPENDED CEILINGS.SUPPORT ALL EQUIPMENT, DUCTWORK, PIPING, CONDUIT AND DEVICES FROM BUILDING STRUCTURE TOPROVIDE A VIBRATION FREE INSTALLATION. NOTIFY ARCHITECT AND STRUCTURAL ENGINEER OF ALLWEIGHTS AND METHODS OF SUPPORT.

28. ANY REFERENCE TO MECHANICAL, PLUMBING, FIRE PROTECTION OR ELECTRICAL CONTRACTORS NOTEDON THE DRAWINGS SHALL NOT BE INTERPRETED AS AN INTENTION TO DEFINE SEPARATE CONTRACTORSFOR THE RESPECTIVE WORK. THE GENERAL CONTRACTOR SHALL COORDINATE AND PROVIDE ACOMPLETE INSTALLATION WITH COMPLETE MECHANICAL, PLUMBING, FIRE PROTECTION ANDELECTRICAL SYSTEMS, REGARDLESS OF ANY REFERENCES TO OTHER TRADE CONTRACTORS.

29. GUARANTEE WORK OF THIS CONTRACTOR IN WRITING FOR A PERIOD OF ONE YEAR FROM THE DATE OFOWNER'S ACCEPTANCE OR CERTIFICATE OF SUBSTANTIAL COMPLETION. PROMPTLY REPAIR OR REPLACEDEFECTIVE MATERIALS, EQUIPMENT, WORKMANSHIP AND INSTALLATIONS THAT DEVELOP DEFECTSWITHIN THIS PERIOD. PROMPTLY AND TO OWNERS SATISFACTION, CORRECT DAMAGE CAUSED INMAKING NECESSARY REPAIRS AND REPLACEMENTS UNDER THIS GUARANTEE AT NO ADDITIONAL COSTTO OWNER. SUBMIT GUARANTEE TO ARCHITECT BEFORE FINAL PAYMENT IS MADE. STATEMENT OFGUARANTEE REQUIREMENTS SHALL NOT BE INTERRUPTED TO LIMIT OWNER'S RIGHTS UNDER LAW ANDTHIS CONTRACT.

1. PROJECT CONDITIONS1.1. THE CONTRACTOR SHALL BECOME COMPLETELY FAMILIAR WITH ALL EXISTING BUILDING AND SITE

CONDITIONS AND LIMITATIONS WHICH MAY HAVE A BEARING ON THE OPERATIONS HEREIN SPECIFIEDAND SHALL INCLUDE ALL WORK REQUIRED TO COMPLETE THE PROJECT AS SHOWN ON THE DRAWINGS.NO EXTRA COMPENSATION WILL BE ALLOWED FOR UNFORESEEN CONDITIONS THAT CAN BEDETERMINED FROM A CAREFUL EXAMINATION OF THE SITE, BUILDING AND DRAWINGS.

1.2. ITEMS OF VALUE WHICH ARE NOT INDICATED TO BE RETURNED TO THE OWNER SHALL BECOME THEPROPERTY OF THE CONTRACTOR. STORAGE OR SALE OF ITEMS ON THE PROJECT SITE IS PROHIBITED.

1.3. PROTECTION: ENSURE THE SAFE PASSAGE OF PERSONS IN AND AROUND THE BUILDING DURINGDEMOLITION. PREVENT INJURY TO PERSONS AND DAMAGE TO PROPERTY. PROVIDE ADEQUATESHORING AND BRACING TO PREVENT COLLAPSE. IMMEDIATELY REPAIR DAMAGED PROPERTY TO THECONDITION BEFORE BEING DAMAGED. TAKE EFFECTIVE MEASURES TO PREVENT WINDBLOWN DUST.

1.4. UTILITIES: MAINTAIN ALL UTILITIES EXCEPT THOSE THAT REQUIRE REMOVAL OR RELOCATION. KEEPUTILITIES IN SERVICE AND PROTECT FROM DAMAGE. DO NOT INTERRUPT UTILITIES SERVING OCCUPIEDAREAS OF THE SITE OR BUILDING WITHOUT FIRST OBTAINING PERMISSION FROM OWNER.

2. REGULATION REQUIREMENTS2.1. STRICTLY COMPLY WITH APPLICABLE CODES, REGULATIONS AND REQUIREMENTS OR AUTHORITY

HAVING JURISDICTION.3. HANDLING OF MATERIALS

3.1. REMOVE DEBRIS FROM THE SITE AS IT ACCUMULATES. DO NOT STORE, SELL, BURN OR OTHERWISEDISPOSE OF DEBRIS ON SITE. REMOVE ALL MATERIAL IN SUCH MANNER AS TO PREVENT SPILLAGE.

4. TRANSFER OF RESPONSIBILITY AND DISPOSITION OF MATERIALS4.1. UPON RECEIPT OF NOTICE TO PROCEED WITH THE WORK, THE TITLE TO ALL MATERIALS FOR

DEMOLITION SHALL BE VESTED. THE CONTRACTOR WHEREUPON THE OWNER WILL NOT BERESPONSIBLE FOR THE CONDITION, LOSS OR DAMAGE TO SAID PROPERTY. ALL SUCH ITEMS SHALL BEREMOVED FROM THE OWNER'S PROPERTY.

5. DISPOSAL OF DEMOLISHED MATERIALS5.1. REMOVE UNUSED EQUIPMENT AND FIXTURES AND ALL ASSOCIATED DUCTWORK AND PIPING SERVICING

EQUIPMENT AND FIXTURES INCLUDING ANY ABANDONED DUCTWORK AND PIPING NOT ASSOCIATEDWITH SAID EQUIPMENT AND FIXTURES AND NOT REQUIRED FOR NEW WORK. REMOVE DUCTWORK ANDPIPING BACK TO THE NEXT LIVE BRANCH WHICH WILL NOT OBSTRUCT THE NEW WORK AND CAP AIR ORWATER TIGHT. TRANSPORT AND LEGALLY DISPOSE OF MATERIALS OFF SITE.

5.2. ALL DEMOLITION SHALL BE COORDINATED WITH OWNER, ARCHITECT, ENGINEER AND GENERALCONTRACTOR. ALL DEBRIS SHALL BE CLEANED UP AND REMOVED FROM THE SITE BY THE END OF EACHWORK DAY. PRIOR TO DISPOSAL OF EQUIPMENT AND MATERIALS, TURN OVER TO OWNER ANYREMOVED EQUIPMENT AND MATERIALS PER OWNER'S REQUEST.

6. CLEAN UP AND REPAIR6.1. UPON COMPLETION OF DEMOLITION WORK, REMOVAL TOOLS, EQUIPMENT AND DEMOLISHED

MATERIALS FROM SITE. REMOVE PROTECTION AND LEAVE INTERIOR AREAS BROOM CLEAN.6.2. REPAIR DEMOLITION PERFORMED IN EXCESS OF THAT REQUIRED. RETURN STRUCTURES AND

SURFACES TO REMAIN IN CONDITION EXISTING PRIOR TO COMMENCEMENT OF SELECTIVE DEMOLITIONWORK. REPAIR ADJACENT CONSTRUCTION OR SURFACES SOILED OR DAMAGED BY SELECTIVEDEMOLITION WORK.

DEMOLITION NOTES

DF

AS

N

OT

ED

JM

F

RP-1

SPECIFICATIONS FOR

ENGRAVED, LAMINATED ACRYLIC

OR MELAMINE LABEL. REFER TO

208Y/120V

ADDITIONAL INFORMATION

EQUIPMENT DESIGNATION

EQUIPMENT VOLTAGE

FIXTURE IN ROOM

TO NEXT LIGHTING

SENSOR

OCCUPANCY

TO NEXT OCCUPANCY

SENSOR IN ROOM

BLUE (CONTROL)

BLACK (COMMON)

RED (+24VDC)

L1

N

G

POWER SWITCH PACK

LIGHTING

FIXTURE

(MAXIMUM OF 5)

TOGGLE SWITCH

(TYPICAL)

6'-0" MAXIMUM LENGTH

MC CABLE

BRANCH CIRCUIT WIRE

AND CONDUIT (TYPICAL)

JUNCTION BOX

(TYPICAL)

J J

E-2

1

SCALE - NONE

DETAIL - NAMPLATE

E-2

2

SCALE - NONE

WIRING DIAGRAM - CEILING MOUNTED OCCUPANCY SENSOR

E-2

3

SCALE - NONE

DETAIL - LIGHTING FIXTURE WIRING

STEEL/UNISTRUT/CEILING/ETC.

SUSPENDED CEILING

FLOOR

18" FOR DATA/PHONE/VOICE OUTLETSUNLESS OTHERWISE SPECIFIED BYARCHITECT

4" SQ X 2 1/8" DEEP BOX WITHRAISED DEVICE COVER

DEPTH OF RAISED COVER =DEPTH OF DRYWALL (+)FINISH COAT

COMMUNICATION CABLERUN IN 1" EMT RACEWAY

PLENUM RATED CABLE(PROVIDE PULL WIRE WHENCABLE IS NOT PROVIDED)

INSTALL BUSHINGON CONDUIT END

E-2

4

SCALE - NONE

DETAIL - DEVICE INSTALLATION

HOT(H)

BLAC

KGROUND

(GND)

GREE

N

GROUND (GND)

HOT (H)BLACK

GREEN

WHITENEUTRAL (N)

NEUTRAL(N)

WHI

TE

120 VOLTSOURCE

E-2

5

SCALE - NONE

DETAIL - TYPICAL DUPLEX RECEPTACLE WIRING

1 CIRCUIT NO. ON PLAN

GROUND BAR GROUND BARNORMAL EQUIPMENT ISOLATED EQUIPMENT

NEAR WALL BOX

AL

UTR

EN

#12 HOT

D

GRD

GRD

20A

AØ BØ

POWER PANEL

20A

BOX

BASE

ON

CONTRACTOR

FLEXIBLE POWER WHIP FURNISHED BY OTHERS

3/4" FLEXIBLE METAL CONDUIT

JUNCTION BOX (FLOOR OR WALL MOUNTED)

FURNITURE NOTES:1. THE FURNITURE WIRING WAS DESIGNED BASED ON A 8 WIRE SYSTEM (3 HOTS, 1 OVERSIZED NEUTRAL, 1 HOT, 1

NEUTRAL AND 2 EQUIPMENT GROUNDS) AS SHOWN WITH 16 CUBICLES PER 8 WIRE CIRCUIT. THE CONTRACTORSHALL TAKE THE RESPONSIBILITY OF REDESIGNING THE LAYOUT IF THE FURNITURE IS DIFFERENT THEN ORIGINALDESIGN PARAMETERS.

208/120 VOLT, 3 PHASE, 4 WIRE

#12 HOT

#12 HOT

#12 HOT

#12 ISOLATED

#12 NEUT

#12 EQUIP GRD

#10 NEUT

RG

CØ

JUNCTION BOX ABOVE CEILING

1 CIRCUIT NO. ON PLAN

WIRE SHALL BE NO. 10 AWGTHE 3 PHASE SHARED NEUTRAL3/4" CONDUIT E.M.T.

CONNECTION

MODULARFURNITURE

AND INSTALLED BY

E-2

6

SCALE - NONE

WIRE MODULAR PARTITION WIRING DIAGRAM

DF

AS

N

OT

ED

JM

F

1. ALL LIGHTING FIXTURES ARE NEW UNLESS NOTED OTHERWISE. COORDINATEEXACT LOCATION OF ALL NEW LIGHTING FIXTURE WITH WITH ARCHITECTURALDRAWINGS. VERIFY ANY QUANTITY DISCREPANCY WITH ARCHITECT AND AEI.

2. ALL LIGHTING CONTROL SHALL BE REPLACED WITH NEW OCCUPANCY WALLSWITCH OR CEILING SENSOR, UNLESS NOTED OTHERWISE. WHERE CONTROLSWITCH IS SHOWN WITH CEILING OCCUPANCY SENSOR, THE SWITCH SHALLBE USED FOR OCCUPANCY SENSOR OVER-RIDE. REFER TO DETAIL 2/E-1.1.

3. COORDINATE PLACEMENT OF WALL SWITCH WITH ARCHITECT DRAWINGSPRIOR TO ROUGH-IN.

4. CONNECT NEW LIGHTING FIXTURES TO EXISTING LIGHTING CIRCUIT BREAKERSIN PANEL 'LP'. LIGHTING CIRCUITS NUMBERS SHOWN ARE FOR REFERENCEONLY.

GENERAL ELECTRICAL

30(E)T

15T

(E)PANELEP

(E)PANELEPB

(E)PANELEL

(E)PANELEO

7.5

(E)PANELPP

(E)TRANSFSWITCH

(E)FACP(E)MAINSWITCHBOARD FF

F

(E)TELE/COM

(E)(E)

(E)PULLBOX

(E)

(E)

(E)

SO

SS

OS

SO

S

SO

S

SO

SS

OS

SO

SS

OS

SO

S

SOS

SO

S

SOS

SOS

SOS

S

SOS

SO

S

SO

SS

OS

OS

OS

OS OS

OS

OS

OSOS

OS

OS

OS

OS

OS

OS

OS

OSOS

OS

SO

SS

OS

S

S

SO

S

SO

S

S

S

S

S

OS

OS

Sa

OS

S S

S

B1 B1A1

B1

B1 B1 B1B1 B1 B1

B1

B1

B1

B1

B1

B1

B1B1

B1

B1B1

B1

B1

B1

B1

B1

B1

B1 B1

B1

B1

B1

B1B1

A1 A1 A1 A1 A1

A1A1

A1 A1

A1A1

A1 A1

A1

A1

A1

A1A1

A1

A1

A1 A1 A1

A1A1

A1

A1A1

A1

A1A1

A1 A1 A1

A1A1

A1 A1 A1

A1

A1

A1

A1 A1 A1

A1 A1 A1 A1

A1

A1

A1 A1

A1

A1

A1

A1A1A1A1

A1 A1 A1

A1

A1

A1A1

A1 A1

A1

A1

A1 A1 A1

A1 A1 A1 A1

A1 A1

A1 A1

A1

A1 A1

A1

A1

A1 A1

A1

A1 A1

A1A1 A1

A1A1 A1

A1

A1

A1

A1

A1

A1

A1

A1A1A1

A1 A1 A1

B1

B1

B1

B1B1

B1

A1 A1

A1

X1X1

X1

X1

X1

X1

X1

X1

X1

X1

S

SOS

X1

X1

X1

X1

OS

OS

OS

OS

OS

OS

OS

OS

S

OS

S S

SSa

F1

F1 F1a a

a

E1

(E)PANELPAB

75

(E)XFMR (E)PANELPA-A

(E)PANELLA

(E)PANELDP

(E)MAINSWITCHBOARD

X1

X1X1

X1

X1

OS

S

S

2 2

2

2

2 2

2

2

2

2

2 2

2

2 2

2

22

2

1

11

1

1

1 1 1 1

1

4

4

4 4

4

1 1

1

1

4 1 1 1

4

4

4

4

4

4

4

4 4

6 6

66

6

6

6 6

6

6 6

6

6

1

3

3

3

3

3 3

3 3

3 3

3

3

3

33

3 3

5

5

5

5

5

5

5 5

5

5

5

5

5 5

5

5 5

55

5

8

8

8

8

8

8

8

8

8

8

88

8

8

8

8

8

8 8

ELECTRICAL PLAN NOTES:

CONNECT NEW SHOWER LIGHTING FIXTURES TO EXISTING 120V CIRCUIT FEEDING LIGHTS.

ALL NIGHTLIGHT/ EMERGENCY LIGHTING FIXTURES AND EXIT SIGNS SHALL BE UN-SWITCHEDAND CONNECTED TO NEAREST EMERGENCY PANEL SERVING AREA.

1

2

1

1

2

2

(TYP)

(TYP)

D1 D1

D1

D1

5

5

55

S S

OS

30(E)T

15T

(E)PANELEP

(E)PANELEPB

(E)PANELEL

(E)PANELEO

(E)PANELDP 7.5

(E)PANELPP

(E)TRANSFSWITCH

(E)FACP(E)MAINSWITCHBOARD FF

F

(E)TELE/COM

(E)(E)

(E)PULLBOX

(E)

(E)

(E)

ALL EXISTING TO REMAIN CEILING DEVICES SHALL BE PROTECTED DURING CONSTRUCTION.IF CEILING TILE IS REPLACED, RELOCATE DEVICE IN SAME LOCATION AFTER NEW WORK ISCOMPLETE.

DISCONNECT AND REMOVE ALL CEILING LIGHTING FIXTURES AND ASSOCIATED CONTROLSTHROUGHOUT SPACE. RETAIN WIRE AND CONDUIT FOR REUSE IN NEW WORK.

COORDINATE THE EXACT QUANTITY OF MECHANICAL EQUIPMENT TO BE DEMOLISHED ORRELOCATED WITH MECHANICAL DRAWINGS.

1.

GENERAL ELECTRICAL

2.

S(R)

S(R)

S(R) S(R

)S(R

) S(R)

(R)S (R

)

S(R) S(R

)S(R

) S(R)

S(R) S(R

)

S(R) S(R

)S(R

) S(R)

S(R) S(R

)

S(R) S(R

)S(R

) S(R)

(E)PANELPAB

75

(E)XFMR (E)PANELPA-A

(E)PANELLA

SS(R

)

(R)(

R)S

S(R

)(R)

SS

(R)S(R)S(R)S

(R)S

ELECTRICAL PLAN NOTES:

COORDINATE CEILING AND WALL DEVICE REMOVAL AND RELOCATION IN MEETING ROOM. AND ADJACENT CORRIDOR. WALL SWITCHESCONTROL VARIES SENSITIVE EQUIPMENT IN THIS ROOM. FIELD VERIFY ALL WORK IN THIS ROOM PRIOR TO BEGINNING CONSTRUCTION.

EXISTING EXHAUST HOOD CONTROL SWITCH TO REMAIN.

REMOVE WIRE TO EXISTING RTU (ON ROOF). REMOVE ALL ASSOCIATED FIRE ALARM AND CONTROLS BACK TO SOURCE.

REMOVE EXISTING WIRE AND CONDUIT TO VAV BOX FOR REMOVAL BY MECHANICAL CONTRACTOR..

ADD-ALT -DISCONNECT AND REMOVE WIRE AND CONDUIT TO EXISTING EXHAUST FAN, FOR REMOVAL BY OTHERS.

ADD-ALT-DISCONNECT AND REMOVE WIRE AND CONDUIT TO EXISTING ROOFTOP EXHAUST FAN.

1

1 1

S(R)

S(R)

S(R)

S(R)

S(R)

S(R)

S(R)

S(R)

S(R)

S(R)

S(R)

S(R) S(R

)

S(R) S(R

)

S (R)S (R

)

S(R

)S

(R)

(R)(

R)S

S

(R)S

(R)

S

(R)S

(R)

S

(R)S

(R)S

1

(R)S

(E)S2

2

4

3.

3

3

3

3

RTU3

RTU2

RTU1

4

4

4

4

4

4

4

4

4

4

4

4

5

5

6

5

6

(R)S

(R)(R)SS

(R)(R)SS

KEY PLAN

PHASE 1

E-1.1

2

SCALE - 1/8" = 1'-0"

ELECTRICAL FLOOR PLAN - LIGHTING - PHASE 1

AS

N

OT

ED

JM

F

DF

E-1.1

1

SCALE - 1/8" = 1'-0"

ELECTRICAL FLOOR PLAN - DEMOLITION LIGHTING - PHASE 1

0' 4' 16'8' 0' 4' 16'8'

B1 B1 B1 B1

B1

B1

B1

B1 B1 B1

B1

B1 B1

B1 B1

B1 B1 B1

A1

A1

A1

A1

A1

A1

A1

A1

A1

A1

A1A1

A1A1

A1

A1

A1

A1

A1

A1

A1

A1

A1

A1

A1

A1

A1

A1 A1

A1 A1

A1

A1A1A1A1

A1 A1

A1 A1

A1 A1 A1

A1

A1A1A1

A1A1A1

A1 A1

A1A1

A1

A1

A1A1A1A1

A1 A1 A1

A1 A1 A1

A1A1

A1

A1 A1A1

A1A1A1

A1 A1

A1 A1 A1

A1

A1

A1 A1

A1

A1

A1

A1 A1

A1

A1A1A1

B1 B1 B1

A1A1

X1 X1

X1

X1

X1

X1

X1

X1

X1

X1

X1

X1

D1 D1

D1 D1

D1 D1

D1 D1 D1 D1

D1 D1

OS OS

OS OS OS

OS

OS

OS

OS

OS OS

OS

OS

OS

OS

OS

OS

OS

OSOS

OS

OS

OS

OS

OS

OS

OS

SO

S

SO

S

SO

S

S

SOS

S

S

S

SOS

S S S

S

Sa

a

a

a

a

a

a

OS OS

OSOS

SOS

SOS

SX1

N.I.C.

S

S

S

S

S

1. ALL LIGHTING FIXTURES ARE NEW UNLESS NOTED OTHERWISE. COORDINATEEXACT LOCATION OF ALL NEW LIGHTING FIXTURE WITH WITH ARCHITECTURALDRAWINGS. VERIFY ANY QUANTITY DISCREPANCY WITH ARCHITECT AND AEI.

2. ALL LIGHTING CONTROL SHALL BE REPLACED WITH NEW OCCUPANCY WALLSWITCH OR CEILING SENSOR, UNLESS NOTED OTHERWISE. WHERE CONTROLSWITCH IS SHOWN WITH CEILING OCCUPANCY SENSOR, THE SWITCH SHALLBE USED FOR OCCUPANCY SENSOR OVER-RIDE. REFER TO DETAIL 2/E-1.1.FOR OFFICE FURNITURE SYSTEM LIGHTS SHALL BE CONTROLLED BY CEILINGSENSOR.

3. COORDINATE PLACEMENT OF WALL SWITCH WITH ARCHITECT DRAWINGSPRIOR TO ROUGH-IN.

4. CONNECT NEW LIGHTING FIXTURES TO EXISTING LIGHTING CIRCUIT BREAKERSIN PANEL 'LB'. LIGHTING CIRCUITS NUMBERS SHOWN ARE FOR REFERENCEONLY.

GENERAL ELECTRICAL

ELECTRICAL PLAN NOTES:

SKY LIGHT FIXTURE SHALL BE CONTROLLED BY PHOTO CELL WITH LOCAL SWITCH OVER RIDE.

ALL NIGHTLIGHT/ EMERGENCY LIGHTING FIXTURES AND EXIT SIGNS SHALL BE UN-SWITCHEDAND CONNECTED TO NEAREST EMERGENCY PANEL SERVING AREA.

1

2

1

1

1

1

1

1

1

1

1

1

1

1

11

1

1

1 1

1

2

2 2

2 2

2

2

2

2

2

22

2

4

4

4

4

1 1 1 1

1 1

D1

D1

3

33

3

3

3

3

3 3 3 3

3

3 3

3

3

3

3 3 3

33

5 5

5 5

5 5

5 5

5

5

5

5

5 5

5 5

5 5

5

5 4

4

4 4

4

4

4

444

4 4 4

4 4

4 4

4

4 4 4

2 (TYP)

2 (TYP)

OS

OS

OS

+

+

++

J

JJ

112.5

(E)T

(E)PANEL SL

(E)PANELPB-B

(E)PANEL PB-A

(E)PANEL LB

S3

S

S

Sb

SDS

OS

OS

OSSSSS

SS

SSD

OSOS

OS

S

SOS SOS SOS

SOS

OS

OS

SOS

OS

OS

Sa

SOSS3

S3OS

S3OSS3OS

SOS

SOS

OS

S3

OS

Sa

OS

OS

OS

SOS SOS

SOS

SOS

OS

OS

Sa

2

TV TV

J

1

TV

SOSSOS

SOSSOS

TV

TV

TV

F

F F

F

FF

J

J

(E) (E)

(E)

(E)

(E)

(E)(E)

(E)

(E)

(E) (E) (E)

(E)

(E)(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)(E)

(E)

(E)(E)

(E)(E)

(E)

(E)

(R)

(E)

(R)

(R)

(R) (R)

(R)

(R)

(R)(R)

(R)

(R)(R)

(R)(R)

(R)

(R)

(R)

(R)

(R) (R)

(R)

(R)

(R)

(R)

(R)

(R)

(R)(R)

(R)

(R)

(R)

(E)

1

1

(R)

(R)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E) (E)

(E)

(E)

(E)(E)

(E)

(E)

(E)(E)

(R)

(R)

(E)

(E)

(E)

(E) (E)(E)

(E)

(E) (E)

(E)

(R)

(R)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(R)

RTU8

3

8

7

7

7

8

7

7

1

11

1

1 1

1

11

1

1

1

1

1

11

1

1

1

1

1

1

REMOVE ALL RECEPTACLES AT WALLS BE DEMOLISHED, COORDINATE DEMOLITION WORK WITH ARCHITECTURAL DRAWINGSAND GENERAL CONTRACTOR.

DISCONNECT AND REMOVE ALL CEILING LIGHTING FIXTURES AND ASSOCIATED CONTROLS THROUGHOUT OFFICE SPACE.RETAIN WIRE AND CONDUIT FOR REUSE IN NEW WORK.

RECEPTACLES AND TELECOMMUNICATION DEVICES SHALL REMAIN IN EXISTING TO REMAIN ROOMS AND WALLS.

FOR ALL EXISTING BLANK COVERS PLATES THROUGHOUT SPACE, PATCH AND PAINT WALL TO MATCH EXISTING CONDITIONS.

VERIFY ALL CEILING DEVICES PRIOR TO DEMOLITION WORK. SECURE DEVICES TO ABOVE CEILING DURING CONSTRUCTION. ALLFIRE ALARM, EMERGENCY, AND SECURITY DEVICES SHALL REMAIN OPERABLE DURING RENOVATION. RELOCATE TO SAMELOCATION WHEN NEW CEILING IS INSTALLED. NEW WIRE AND CONDUIT EXTENSION SHALL MATCH EXISTING.

COORDINATE THE EXACT QUANITIY OF MECHANICAL EQUIPMENT TO BE DEMOLISHED OR RELOCATED WITHMECHANICAL DRAWINGS

1.

GENERAL ELECTRICAL

2.

3.

4.

5.

ELECTRICAL PLAN NOTES:

COORDINATE CEILING AND WALL DEVICE REMOVAL AND RELOCATION IN MEETING ROOM. AND ADJACENT CORRIDOR.WALL SWITCHES CONTROL VARIES SENSITIVE EQUIPMENT IN THIS ROOM. FIELD VERIFY ALL WORK IN THIS ROOM PRIORTO BEGINNING CONSTRUCTION.

COORDINATE RELOCATION OR REMOVAL OF EXISTING SILENT ALARM SYSTEM TO POLICE STATION.

REMOVE WIRE AND CONDUIT TO EXISTING RTU (ON ROOF). REMOVE ALL ASSOCIATED FIRE ALARM AND CONTROLS BACKTO SOURCE.

REMOVE EXISTING WIRE AND CONDUIT TO VAV BOX FOR REMOVAL BY MECHANICAL CONTRACTOR..

ADD-ALT -DISCONNECT AND REMOVE WIRE AND CONDUIT TO EXISTING EXHAUST FAN, FOR REMOVAL BY OTHERS.

ADD-ALT-DISCONNECT AND REMOVE WIRE AND CONDUIT TO EXISTING ROOFTOP EXHAUST FAN.

DISCONNECT FURNITURE SYSTEM FEED TO FURNITURE SYSTEM FOR REMOVAL BY OTHERS. RETAIN FURNITURE SYSTEMWHIP, WIRE AND CONDUIT FOR REUSE IN NEW WORK.

DISCONNECT AND REMOVE FURNITURE POWER POLE. REMOVE ALL POWER AND TELE DATA WIRING AND CONDUIT BACKTO SOURCE.

1

2

3

4

5

6

6.

7

8

KEY PLAN

PHASE 2

AS

N

OT

ED

JM

F

DF

E-1.2

2

SCALE - 1/8" = 1'-0"

ELECTRICAL FLOOR PLAN - LIGHTING - PHASE 2

E-1.2

1

SCALE - 1/8" = 1'-0"

ELECTRICAL FLOOR PLAN - DEMOLITION LIGHTING - PHASE 2

0' 4' 16'8'

0'4' 16'8'

30(E)T

15T

(E)PANELEP

(E)PANELEPB

(E)PANELEL

(E)PANELEO

(E)PANELDP 7.5

(E)PANELPP

(E)TRANSFSWITCH

(E)FACP(E)MAINSWITCHBOARD FF

F

(E)TELE/COM

(E)(E)

(E)PULLBOX

(E)

(E)

(E)

SHEET NOTES:

1. ALL SINGLE PHASE BRANCH CIRCUITING SHALL BE 2#12 & 1#12GND - 3/4"C UON. ALL THREE

PHASE BRANCH CIRCUITING SHALL BE 3#12 & 1#12GND - 3/4"C UON. ROUTE ALL BRANCH

CIRCUITS TO PANEL INDICATED IN ROOM UON. REFER TO SINGLE LINE DIAGRAM FOR

ADDITIONAL WIRE SIZES.

2. REFER TO APPROPRIATE TRADE DRAWINGS FOR EXACT LOCATION OF HVAC, PLUMBING, AND

ARCHITECTURAL EQUIPMENT.

3. ALL EXISTING FIRE ALARM AND SECURITY SHALL REMAIN., RELOCATE ANY CEILING DEVICE

WHERE CEILING IS REPLACED. CONNECT NEW DEVICES TO EXISTING FIRE ALARM SYSTEM.

MODIFIY SYSTEM AS REQUIRED TO ACCOMMODATE NEW DEVICES.

F

F

F

(E)

(E)

F(E)

F(E)

F

(E)

F

(E)

F

(E)

F

(E)

(E)PANELPAB

75

(E)XFMR (E)PANELPA-A

(E)PANELLA

EFM-2

EFP-2

EFP-1

(E)

F(N)

F(N)

F(N)

F(N)

F(N)

F(N)

F(N)

F(N)

F(N)

F(N)

F(N)

RTU2

RTU1

(N)

ELECTRICAL PLAN NOTES:

CONNECT TO EXISTING PANEL FEEDING RTU(S) PROVIDE NEW 45A BREAKER AND 3#6, +GND IN EXISTING CONDUIT.NEW BREAKER SHALL MATCH EXISTING CONDITIONS.

PROVIDE NEW DUCT DETECTORS ON RETURN SIDE OF ALL RTU UNITS AS SHOWN ON MECHANICAL DRAWING. CONNECT TO FIREALARM SYSTEM.

CONNECT TO EXISTING PANEL DP IN MAIN ELECTRICAL ROOM PROVIDE NEW 20A BREAKER AND 3#12, +GND IN 3/4" CONDUIT.NEW BREAKER SHALL MATCH EXISTING CONDITIONS.

FOR ADD ALTERNATE EXHAUST FANS. IF EXISTING CIRCUIT IS NOT SUITABLE, PROVIDE 20/1 BREAKER IN EXISTING PANEL IF SPAREBREAKER IS NOT AVAILABLE. NEW BREAKER SHALL MATCH EXISTING BREAKERS.

1

1

1

2

2

2

RTU3

32

3

PANEL LACIRCUIT #34

PANEL LACIRCUIT #36

PANEL LACIRCUIT #38

4

4

4

4

RTU4

3F(N)

F(N)

KEY PLAN

PHASE 1

E-2-.1

1

SCALE - 1/8" = 1'-0"

ELECTRICAL FLOOR PLAN - POWER - PHASE 1

AS

N

OT

ED

JM

F

DF

0'4' 16'8'

J

JJ

J

(E)

(E)

(E) (E) (E)

(E)

(E)(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)

(E)(E)

++

112.5

(E)T

30(E)T

15T

(E)PANELEP

(E)PANELEPB

(E)PANELEL

(E)PANELEO

(E)PANELDP 7.5

(E)PANELPP

(E)TRANSFSWITCH

(E)FACP(E)MAINSWITCHBOARD FF

F

(E)TELE/COM

(E)PANEL SL

(E)PANELPB-B

(E)PANEL PB-A

(E)PANEL LB

(E)(E)

(E) (E)

(E)PULLBOX

(E)

(E)

(E)

(E)

ELECTRICAL PLAN NOTES:

CONNECT TO EXISTING PANEL FEEDING RTU(S) PROVIDE NEW 45A BREAKER AND 3#6, +GND IN EXISTING CONDUIT.NEW CIRCUIT BREAKER SHALL MATCH EXISTING CONDITIONS. COORDINATE CONDUIT ROUTING WITH MECH CONTRACTOR.

PROVIDE NEW DUCT DETECTORS ON RETURN SIDE AS SHOWN ON MECHANICAL DRAWING. CONNECT TO FIRE ALARM SYSTEM.

VERIFY ELECTRICAL REQUIREMENTS FOR NEW FURNITURE SYSTEM. MODIFY EXISTING FURNITURE FEED LOCATIONS OR PROVIDENEW FEEDS TO MEET REQUIREMENTS OF NEW SYSTEM. PROVIDE NEW CIRCUITS AS REQUIRED TO EXISTING PANELBOARDS.PROVIDE ALL NECESSARY MODIFICATIONS IN FIELD TO INSTALL SYSTEM, INCLUDING NEW BREAKERS AND WIRING AND CONDUIT.

ADD ALTERNATE; EXHAUST FAN. CONNECT TO EXISTING SPARE BREAKER ON PANEL PB-B.

1

2

3

3

3

3

3

RTU8

RTU7

1

2

2

(E)

2

(E)

RTU5

J(E) 3

CONNECT NEWRECEPTACLES TOEXISTING BRANCHCIRCUIT FEEDINGSIGN-IN AREA.

(E)

(E)

COORDINATE DATAAND SECURITYREQUIREMENTSWITH TREDYFFRIN

SHEET NOTES:

1. ALL SINGLE PHASE BRANCH CIRCUITING SHALL BE 2#12 & 1#12GND - 3/4"C UON. ALL THREE

PHASE BRANCH CIRCUITING SHALL BE 3#12 & 1#12GND - 3/4"C UON. ROUTE ALL BRANCH

CIRCUITS TO PANEL INDICATED IN ROOM UON. REFER TO SINGLE LINE DIAGRAM FOR

ADDITIONAL WIRE SIZES.

2. REFER TO APPROPRIATE TRADE DRAWINGS FOR EXACT LOCATION OF HVAC, PLUMBING, AND

ARCHITECTURAL EQUIPMENT.

3. ALL EXISTING FIRE ALARM AND SECURITY SHALL REMAIN., RELOCATE ANY CEILING DEVICE

WHERE CEILING IS REPLACED. CONNECT NEW DEVICES TO EXISTING FIRE ALARM SYSTEM.

MODIFIY SYSTEM AS REQUIRED TO ACCOMMODATE NEW DEVICES.

EFM-1

4

4

KEY PLAN

PHASE 2

E-2.2

1

SCALE - 1/8" = 1'-0"

ELECTRICAL FLOOR PLAN - POWER - PHASE 2

AS

N

OT

ED

JM

F

DF

0' 4' 16'8'

1. ALL LIGHTING FIXTURES ARE NEW UNLESS NOTED OTHERWISE. COORDINATEEXACT LOCATION OF ALL NEW LIGHTING FIXTURE WITH WITH ARCHITECTURALDRAWINGS. VERIFY ANY QUANTITY DISCREPANCY WITH ARCHITECT AND AEI.

2. COORDINATE PLACEMENT OF WALL SWITCH WITH ARCHITECT DRAWINGSPRIOR TO ROUGH-IN.

3. CONNECT NEW LIGHTING FIXTURES TO EXISTING LIGHTING CIRCUIT FEEDINGAREA.

GENERAL ELECTRICAL

ELECTRICAL PLAN NOTES:

(4)NEW DECORATIVE LED HIG BAY LIGHTING FIXTURES SHALL BE HUBBELL #SAV MH 35 8 22" U N WW. FIXTURESHALL BE MOUNTED AT 18' ABOVE FINISHED FLOOR. PROVIDE DIMMER FOR LIGHTING CONTROL.

NEW RECESSED DOWN LIGHTS SHALL CONNECTED TO EXISTING BRANCH CIRCUIT IN AREA.COORDINATE LOCATION FOR NEW DIMMER SWITCH CONTROLLING LOBBY LIGHTS.

1

2

2

1

1

1

1

a a

aa

aa

a a

2 2

2 2

2 2

2

SDa

E1

E1 E1

E1

E1

E1 E1

E1

KEY PLAN

PHASE 3

E-2.3

1

SCALE - 1/8" = 1'-0"

ELECTRICAL FLOOR PLAN - LIGHTING - PHASE 3

AS

N

OT

ED

JM

F

DF

0' 4' 16'8'