hyundai genuine accessories€¦ · hyundai genuine accessories no good click when disconnecting...
TRANSCRIPT
HYUNDAI Genuine Accessories
Vehicle Model Elantra Accessory Interior Lighting Kit
Model Year 2017 ~ Difficulty ( B )
Basic Required Hand Tools
Instructional Symbols / Definitions
Difficulty stated above reflects the minimum level of expertise required to install
the accessory.
( A ) Customer ( B ) Dealer Technician ( C ) Master Technician
Note:
For SE models with Base Radio: Use Pin-8 and Pin-10 of the 16-Pin AUX Connector for the power connections.
Part No. F3068 ADU00
NOTE: THIS INTERIOR LIGHT KIT IS NOT APPLICABLE TO MANUAL TRANSMISSION, 1.4T ECO, OR SPORT ELANTRA MODELS.
- Accessory Installation
Ratchet 10mm Socket 13mm Socket Wire Cutters
Pliers Center PunchTorque Wrench
Electric Drill 19/32" Drill Bit#2 Phillips
Screwdriver
Nylon Trim Panel
Removal Tool
Tape Measure
Deburring Tool
3/16" Drill Bit Scissors
Denotes safety equipment required to be used such as a mask, safety glasses, gloves, and hearing protection.
Safety Glasses
Hearing Protection
Mask
Gloves
Denotes instructional steps necessary to complete the process.
Denotes quality processes to be checked prior to moving to the next step.
Denotes cautions to be taken to avoid physical injury or electronic component damage.
Denotes warnings that may lead to serious physical injury or vehicle damage.
Denotes specific tools that are necessary to complete the step.
Denotes cautions to be taken to avoid vehicle and component damage.
Notes to the Installer: 1) Read the entire installation instructions prior to beginning the installation of this accessory. 2) Make sure the vehicle is completely clean before the accessory is installed. 3) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed. 4) To prevent vehicle damage, never place tools on top of painted surfaces, seats, dash pad, console or floor carpet/mats. 5) Always wear appropriate safety gear to include gloves and safety glasses when required. 6) Factory wire colors are subject to change, please use the specified pin # in the harness connector to identify the correct wire for T-Tap installation.
FMVSS 110 Compliance Information
Part Number: F3068 ADU00
0.67 lbs 0.3 kg
(Gross Weight)
All dealers must determine if the weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories. Load Label Part Number:
NP070 - 09003
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 1 of 15
1 20 2 2
Description
LED & Bracket Assembly
HYUNDAI Genuine Accessories
Kit Overview
No. Qty.
LED
1 1
Wire Harness
2 1
Hardware Bag
4
3 1
5 1
Switch
6 1 Installation Instructions
Hardware Total
E
7 1
Hardware Overview
A C D
Plastic FastenerM8 x 1.5mm Flanged
Head NutWire Ties * T-Tap
25
* Extra components intentionally placed in kit as spares.
Please follow directions for proper placement of each component.
1
Glove Box Information Card
1
3
5 6 7 4
2
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 2 of 15
Disconnecting Connectors Lock Connectors
When disconnecting connectors, grasp the connectors , not the wire When locking connectors, listen for a click indicating
they are securely locked.
HYUNDAI Genuine Accessories
NO GOOD
CLICK
When disconnecting connectors, press the lock tab and pull apart by grasping the connectors. DO NOT PULL ON WIRES.
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 3 of 15
N
O
T
E
1. Continue to pull the Shift Knob up to remove the Shift Knob Assembly.
2. Store the Shift Knob Assembly in a safe location for reinstallation.N
O
T
E
1. Close the Forward Tray Cover.
2. Dislodge the Center Console Cover by gently pulling upwards to release
the four (4) pressure clips.
Caution: DO NOT scratch the Trim Panels or Shift Knob Assembly. Caution: DO NOT scratch the Trim Panels.
DO NOT lose the pressure clips.
3 Nylon Trim Panel Removal Tool 4
N
O
T
E
1. Park the vehicle on a level surface.
2. Apply the Parking Brake.
3. Move the Gear Selector from Park (P) position to Drive (D) position.
4. Record all pre-set radio stations (if applicable).
5. Disconnect and isolate the vehicle's Negative Battery Cable.
N
O
T
E
1. Carefully release the six (6) clips surrounding the Shifter Boot by
gently pulling the Shift Knob upwards.
WARNING! Shock Hazard. Do not touch vehicle's negative battery
terminal to vehicle's positive battery terminal. Serious physical injury
or vehicle damage may occur.
Caution: DO NOT scratch the Trim Panels or Shifter Boot.
HYUNDAI Genuine Accessories
Ratchet and 10mm Socket 1 2
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 4 of 15
HYUNDAI Genuine Accessories
5 Nylon Trim Panel Removal Tool 6
N
O
T
E
1. Lift the Center Console Cover to access the Electrical Connectors.
2. Disconnect any Electrical Connectors and remove the Center Console
Cover from the vehicle.
3. Store the Center Console Cover in a safe location for reinstallation.
N
O
T
E
1. Remove the passenger side HVAC Close Out Panel by pressing the
three (3) tabs rearward.
2. Store the HVAC Close Out Panel in a safe location for reinstallation.
Caution: DO NOT scratch the Center Console Cover. Caution: DO NOT scratch the HVAC Close Out Panel or surrounding
Trim Panels.
#2 Phillips Screwdriver 7 8
N
O
T
E
1. In driver side footwell area, remove the one (1) plastic screw
and one (1) push clip as noted in step 8.
2. Route the Interior Light Wire Harness (Driver Side Label) through the
front left side of the Center Console, towards the Driver Side Footwell
area.
N
O
T
E
1. Pull the Interior Light Wire Harness (Driver Side Label) completely
through
to the Driver Side Footwell area as shown.
2. Pull the Harness, taking up all the slack.
3. Replace the one (1) plastic screw and one (1) push clip removed in
step 7.
Caution: Make sure not to route the Harness near any sharp edges. Caution: Make sure not to route the Harness near any sharp edges.
Plastic Screw
Interior Light Wire Harness Driver Side
HVAC Close Out Panel under Glove Box.
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 5 of 15
HYUNDAI Genuine Accessories
9 Wire Cutters, Ratchet, 13mm Socket and Torque Wrench 10
N
O
T
E
1. Locate the unused M8 stud high up on the bulkhead, just below the
large factory wire harness.
2. Mount the driver side LED assembly, using one (1) M8 nut as shown.
Hand tighten only.N
O
T
E
1. Secure LED assembly to vehicle main harness, that passes through the
bulkhead grommet, using one (1) wire tie as shown.
2. Torque M8 Nut to 9.8 - 14.7 Nm (1.0 - 1.5 kgf.m, 7.2 - 10.8 lb-ft).
3. Trim excess wire tie material.
11 12
N
O
T
E
1. On driver's side, route harness up beside HVAC housing and secure
to side of housing with wire tie #1. Do not fully tighten wire tie.
2. Continue to route the harness up above the HVAC vent and secure with
wire tie #2 to factory HVAC damper actuator harness. Do not fully tighten
wire tie.
3. Route the harness down and secure with wire tie #3 to forward white
connector on MDPS module. Do not fully tighten wire tie.
N
O
T
E
1. Route the harness across the top of the MDPS module over towards the
fuse box area.
2. Secure the harness to the 2-Pin MDPS power and ground connector with
wire tie #4. Do not fully tighten wire tie.
3. Route the harness around the MDPS module and along the large factory
harness towards the LED/bulkhead, and secure with wire tie #5 and #6
as shown. Do not fully tighten wire ties.
Caution: Be sure not to route the Interior Light Harness near any sharp
edges.
Caution: Be sure not to route the Interior Light Harness near any sharp
edges.
Wire Tie
Factory Harness
M8 Nut
Large Factory Wire Harness
MDPS Module
Center Console Side Panel
Interior Light Wire Harness
HVAC Vent
Wire Tie #1
Wire Tie #2
Wire Tie #3
Wire Tie #4
Wire Tie #5
MDPS Module Bottom View
Interior Light Wire Harness
Wire Tie #6
Top View
Wire Tie #4
Steering Column
Bulkhead Grommet
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 6 of 15
HYUNDAI Genuine Accessories
Wire Cutters 13 #2 Phillips Screwdriver 14
N
O
T
E
1. Finally, connect the harness to the LED.
2. Adjust slack in the harness to ensure it is routed evenly without
any tight or loose spots.
3. Once slack is adjusted, fully tighten all six (6) wire ties in the
driver side footwell area.
4. Trim excess wire tie material.
N
O
T
E
1. In passenger side footwell area, remove the one (1) plastic screw and
one (1) push clip.
2. Route the Harness (Passenger Side Label) through the front of the
Center Console towards the Passenger Side Footwell area as shown.
Caution: Be sure not to route the Interior Light Harness near any sharp
edges or where harness can be pinched.
Caution: Make sure not to route the Harness near any sharp edges.
15Scissors, Center Punch, Electric Drill, 3/16" Drill Bit and
Deburring Tool16
N
O
T
E
1. Pull the Harness (Passenger Side Label) completely through to the
Passenger Side Footwell area as shown.
2. Replace the one (1) plastic screw and one (1) push clip removed in
step 14.N
O
T
E
1. Using Scissors, cut out the Passenger Side LED Template from
the back of these installation instructions.
2. Remove the white sound insulation from the HVAC close out panel in
area shown above where template is positioned.
3. Place the Template on the HVAC Close Out Panel and mark the two (2)
Mounting Holes using a Center Punch.
4. Using an Electric Drill and 3/16" Drill Bit, drill the two (2) outer LED
Mounting Holes.
5. Deburr the two (2) holes using a deburring tool.
Caution: Make sure not to route the Harness near any sharp edges. Be careful not to enlarge the hole while drilling and deburring.
Mark and drill 3/16"
Plastic Screw and Push Clip
Interior Light Wire Harness
Wire Tie #6
Interior Light Wire Harness
LED
Wire Tie #4
Wire Tie #5
Passenger Side LED Template
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 7 of 15
HYUNDAI Genuine Accessories
17 18
N
O
T
E
1. Install the LED onto the HVAC Close Out Panel as shown, using the
two (2) provided plastic fasteners.
2. Make sure the LED Connector Opening is facing towards the
front of the vehicle (bulkhead).
3. Reinstall the white sound insulation to the HVAC close out panel.
N
O
T
E
1. Connect the Interior Light Harness to the LED.
2. Adjust the Interior Light Harness to allow the HVAC Close Out Panel to
be lowered onto the floor carpet for service access.
Caution: Do not install HVAC close out panel yet. Image above shows
harness route for clarity.
Wire Cutters 19 Scissors, Center Punch, Electric Drill and 3/16" Drill Bit 20
N
O
T
E
1. Using one (1) wire tie, secure the Interior Light Harness to factory HVAC
connector as shown on passenger side footwell area.
2. Trim excess wire tie material.
3. Reinstall the HVAC Close Out Panel while tucking the Interior Light
Harness above the insulated pad area as noted in Step 16.
N
O
T
E
1. Using Scissors, cut out the Switch Template from the back
of these installation instructions.
2. Place the Template in the Center Console Cover and mark the
hole using a Center Punch as noted above.
3. Using an Electric Drill and 3/16" Drill bit, drill a pilot hole.
Caution: Be sure not to route Interior Light Harness near any sharp
edges.
Connector Opening Facing Bulkhead
Switch Template
Mark and drill 3/16"
Interior Light Wire Harness
Wire Tie
HVAC Factory Connector
Interior Light Wire Harness
Plastic Fasteners
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 8 of 15
N
O
T
E
N
O
T
E
1. Using an Electric Drill and 19/32" Drill Bit, drill the hole in the
Center Console Cover.
2. Deburr the hole using a Deburring Tool.
Be careful not to enlarge the hole while drilling and deburring.
22
1. Insert the Switch into the hole.
- Make sure the Switch snaps in tightly and is oriented correctly as
shown.
HYUNDAI Genuine Accessories
Electric Drill, 19/32" Drill Bit and Deburring Tool 21
Pliers 23 Wire Cutters 24
N
O
T
E
1. At the Center Console area, locate the 12-Pin AUX Connector.
2. Connect one (1) T-Tap to the Blue Wire at Pin #4 as shown.
3. Connect one (1) T-Tap to the Gray Wire at Pin #6 as shown.
4. Connect the Blue Wire from the interior Light Harness to the T-Tap
at Pin #4.
5. Connect the Gray Wire from the interior Light Harness to the T-Tap
at Pin #6.
- Refer to the T-Tap Installation Procedure on page 3.
* For SE models with Base Radio: Locate the 16-Pin AUX Connector
and connect one (1) T-Tap to the Blue wire at Pin #8 and one (1)
T-Tap to the Gray wire at Pin #10.
N
O
T
E
1. Using one (1) wire tie, secure the Interior Light Harness as shown.
2. Trim excess wire tie material.
Caution: Be sure to install the T-Taps on the correct vehicle wires.
Make sure you connect the correct wire to the correct T-Tap. There
may be several wires of the same / similar color, please refer to Pin #
position identified on power connector.
Caution: Make sure not to route the Harness near any sharp edges.
Drill 19/32"
Pin #4 (Blue Wire)
Pin #6 (Gray Wire)
Wire Tie
Pin # 8 Blue Wire
Pin # 10 Grey Wire
16-Pin AUX Connector
12-Pin AUX Connector
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 9 of 15
N
O
T
E
1. Connect the switch to the switch leg of the Interior Light Harness.
2. Using two (2) wire ties, secure the switch harness and Interior
Light Harness to the Factory Harness as shown above on the
console cover. If the vehicle application does not have the factory
harness, then secure the switch harness to the "L" shaped anchor clip
with one (1) wire tie as noted above.
3. Trim excess wire tie material.
4. Reinstall the Center Console Cover and Shift Knob assembly.
N
O
T
E
1. Place the Glove Box Information Card in the Glove Box.
2. Reconnect the vehicle's Negative Battery Cable and torque
to 5 Nm (0.5 kgf-m, 44.16 lb-in).
3. Move the Gear Selector from Drive (D) position to Park (P) position.
4. Program radio pre-sets recorded in step 1 (if applicable).
5. Perform the Function Check and Visual Check on the following page.
6. Installation is complete.
WARNING! Shock Hazard. Do not touch vehicle's negative battery
terminal to vehicle's positive battery terminal. Serious physical injury
or vehicle damage may occur.
Wire Cutters 27 Ratchet, 10mm Socket and Torque Wrench 28
N
O
T
E
1. Using one (1) wire tie, bundle the Switch Harness and secure to the
factory AUX/USB harness in the center console, as shown. Bundle
length should be about 15" (381mm).
2. Using one (1) wire tie, secure the driver side leg of the Interior Light
Harness in the center console, as shown
3. Trim excess wire tie material.
N
O
T
E
1. Using one (1) wire tie, secure the passenger side leg of the Interior Light
Harness in the center console, as shown.
2. Trim excess wire tie material.
Caution: Make sure not to route the Harness near any sharp edges. Caution: Be sure not to route interior light harness near any sharp
edges.
HYUNDAI Genuine Accessories
Wire Cutters and Tape Measure 25 Wire Cutters 26
Wire Tie
Wire Tie
Wire Harness
Wire Tie
Wire Harness
Wire Tie
Wire Tie
Switch Harness
Anchor Clip
Installed In Step 25
Installed In Step 25
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 10 of 15
* NOTE: SE models with Base Radio have a 16-Pin AUX Connector. Unse Pin-8 and Pin-10 for power T-Taps.
Items To Be Checked Results Of The Check
Check the On / Off function of the Switch. Interior Lights should turn on and off when switch is in
the on position and headlamps are on.
Make sure to leave the interior light kit switch ON
after the Function Check is complete.
Visual Check
Item To Be Checked
HYUNDAI Genuine Accessories
Function Check
Items To Be Checked Results Of The Check
Check that the blue LED interior lights are illuminated
in Driver and Passenger side footwell areas when
both the vehicle headlamps and the On/Off switch
(installed with the kit) are on.
Interior lights should function with the headlamps on.
Check that the footwell light illumination changes
when using the vehicle Dimmer Switch.
Check that Blue LED Interior Lights are illuminated in
both Driver and Passenger side footwell areas.
Blue LED Interior Lights are illuminated.
Interior lights should become brighter and dimmer
when operating the vehicle Dimmer Switch.
Interior lights are in the ON position after the
Function Check is completed.
Blue LED interior lights not illuminated. Check:
- switch is in ON position.
- fuse is properly installed and intact.
- that T-Taps are installed on the correct wires*.
- spade terminals are installed correctly to the T-Taps.
- The LED's are connected to the interior light kit harness.
Issue / Concern
Troubleshooting
Blue LED interior lights do not operate with the vehicle
illumination circuit.
Check:
- switch is in ON position.
- fuse is properly installed and intact.
- that T-Taps are installed on the correct wires*.
- spade terminals are installed correctly to the T-Taps.
Blue LED interior lights do not dim with vehicle
illumination circuit.
Check:
- switch is in ON position.
- fuse is properly installed and intact.
- that T-Taps are installed on the correct wires.
- spade terminals are installed correctly to the T-Taps.
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 11 of 15
HYUNDAI Genuine Accessories
Electrical Schematic
ILL +
ILL - Legend G - Gray Factory Wire B - Blue Factory Wire
- Wire T-Tap
ILL + Positive Illumination Circuit ILL - Negative Illumination Circuit
G
B
B
G
B
B
G
G
B
Interior Light Kit
Push Button Switch
LED Module LH
LED Module RH
1A Fuse
B
G
1A Fuse is located under
the Center Console Cover.
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 12 of 15
HYUNDAI Genuine Accessories
Template - LED Passenger Side on
HVAC Close Out Panel
2 - 7/16"
3 - 13/16"
3 - 3/16"
5/8"
1 -
13
/16
" 2
- 5/8
"
NOTE: 1. Set printer scaling to “No Scaling” or “Actual Size” before printing template. The template will not print to scale if other settings are used. 2. After printing, use a ruler or tape measure to verify the dimensions shown on the template. 3. Once the dimensions are verified, cut the template out and continue with the installation.
1” Square
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 13 of 15
HYUNDAI Genuine Accessories
This page intentionally left blank
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 14 of 15
HYUNDAI Genuine Accessories
Template - Switch Location on
Center Console Cover Bin
NOTE: 1. Set printer scaling to “No Scaling” or “Actual Size” before printing template. The template will not print to scale if other settings are used. 2. After printing, use a ruler or tape measure to verify the dimensions shown on the template. 3. Once the dimensions are verified, cut the template out and continue with the installation.
Switch Template 1
- 9/1
6"
11
/16
"
1 - 9/16"
4 - 5/16"
Elantra
Interior Lighting Kit
Revision Date
07/27/2016 Page 15 of 15