i job performance measure exam page: -- -i. ii 25-may-2006 job performame measure exam -- p i page:...

* I 1

-I. I Page: Job Performance Measure Exam -- 30-May-2006

JF’M NO JR015.004 Perform a Plant Calorimetric per 0-6.3

Revision #: 4

Review Date: 5/30/2006

Location: In Plant

Estimated Time (minutes): 20.00

Candidate:

Evaluator:

Actual Time: .d

Trainee Performance: Satisfactory Unsatisfactory

Trainee:

Instructor:

Submitted By Date

Reviewed By Date

Page: 2 Job Performance Measure Exam --

30-MUY-2006 ~

‘L/

NOTE

THE EVALUATOR WILL EXPLAIN THE JPM INITIAL CONDITIONS AND PROVIDE CLARIFICATION AS REQUIRED. THE EXAMINEE MAY USE ANY CONTROLLED COPY REFERENCES THAT ARE NORMALLY AVAILABLE IN THE CONTROL ROOM, INCLUDING LOGS. MAKE ALL WRITTEN REPORTS, ORAL REPORTS, AND LOG ENTRIES AS IF THE EVOLUTION WAS ACTUALLY BEING PERFORMED. THE EVALUATOR WILL BE TAKING NOTES. ASK FOR CLARIFICATION OF JPM REQUIREMENTS PRIOR TO THE BEGINNING OF JPM PERFORMANCE.

Initial Conditions: The PPCS calorimetric calculation is not operable and the LEFM is not being used.

Initiating Cues :

The Control Room Foreman has directed you to perform a maximum unit power calculation per 0-6.3. For this JPM an Auxiliary Operator will collect field data collect and provide it to you. Although the PPCS calorimetric calculation function is not operable, the PPCS is operable and may be used as necessary.

‘W’

Page: Job Perfurmanee Measure Exam --

30-May-2006

'- Description: Perform a Plant Calorimetric per 0-6.3 (JR015.004)

JPM Tasks

Task ID: 193-001-01-01B

Task Standards :

In accordance with the procedure

Tools :

Calculator

Safety Glasses

Hard Hat

Hearing Protection

Terminating Cues

--. Task Completion

References :

ID - PRO 0-6.3 PRO 0-6.3.1

Description Review Date Ref Flag

MAXIMUM UNIT POWER STEAM GENERATOR BLOWDOWN CORRECTION FACTOR

Safety Considerations

Consequences of Inadequate Performance: Thermal design limit challenge

General Comments :

Provide a copy of 0-6.3 and 0-6.3.1

.--

Page: 4 Job Performance Measure Exam _- . -

3 0-May-2 006

Performance Checklist

Element : Conditions : Standards : Obtain current 0-6.3 and 0-6.3.1. NOTE: It is permissible to only

obtain Attachment I and I1 of 0-6.3 and Attachment I of 0-6.3.1.

Same as element.

Comments :

Satisfactory Unsatisfactory

Element : CRITICAL Conditions : Standards : Properly collect and record data required by 0-6.3 Attachments I and 11. deviation high alarm on PPCS) do -MCB

NOTE: If either RTD is unreliable (S/G RTD feedwater temperature

not use RTD data, instead use the average T/C feedwater temperature and apply for both loops.

Obtains data from: -PPCS if available

-NIS

Note: Provide Barton Data obtained by the A 0 to the examinee

Comments :

Satisfactory n Unsatisfactory 0 Element : CRITICAL Conditions : Standards : Properly collect and record data for Blowdown Correction Factor per 0-6.3.1, Attachment I.

CUE: When Data Properly Collected the hand out per collected data for calculations.

Obtain the S/G blowdown flow, temperature and pressure +/- 20 psig for each S/G from the blowdown panel.

Comments :

Satisfactory Unsatisfactory [7

Element : CRITICAL Conditions : Standards : Properly perform calculations per 0-6.3.1, Attachment I.

1) Same as element. 2) If interpolate any value between selected rows. 3) Fq +/- .05.

Comments :

Satisfactory Unsatisfactory 0

I 1

- . - 5. I Page: Job Performance Measure Exam 30-May-2006 w Element: CRITICAL Conditions : Standards :

Properly perform calculations per 0-6.3, Attachment I and 11.

NOTE: If action is required per step 5.3.2, DO NOT take action. Advise the Shift Supervisor or CRF of any problems noted.

Same as element.

+/- 0.5% of calculated answer.

Comments :

Satisfactory n Unsatisfactory 0 6 Element : Conditions :

Recommends appropriate action if

Comments :

100% power.

Satisfactory 0

Standards : Same as element.

Unsatisfactory 0 7 Element : Conditions : Standards :

Compares calorimetric to NIS, recommends action if action. disagreement exists.

TERMINATING CUE: No further Same as element.

NOTE: Attach completed 0-6.3 and 0-6.3.1 to this JPM.

Comments :

Satisfactory 0 Unsatisfactory 0 JPM Questions

Question

Answer

References

Reference Type Reference ID Description Ref Flag

Page: 1 I 25-May-2006 Job Performance Measure Exam -- - -

JPMNO JR341.002

0-6.13 Daily Performance Log Attachment I

Revision #: 0


Location: Simulator


Candidate:

Evaluator:

Actual Time: -


Trainee:

Instructor:

Submitted By

Reviewed By

Date

Date

Page: - 2 Performame Measure Exam --

2 5-M~ry-2 0 06 ~

I I

'.d

NOTE

THE EVALUATOR WILL EXPLAIN THE JPM INITIAL CONDITIONS AND PROVIDE CLARIFICATION AS REQUIRED. THE MAMINEE MAY USE ANY CONTROLLED COPY REFERENCES THAT ARE NORMALLY AVAILABLE IN THE CONTROL ROOM, INCLUDING LOGS. MAKE ALL WRITTEN REPORTS, ORAL REPORTS, AND LOG ENTRIES AS IF THE EVOLUTION WAS ACTUALLY BEING PERFORMED. THE EVALUATOR WILL BE TAKING NOTES. ASK FOR CLARIFICATION OF JPM REQUIREMENTS PRIOR TO THE BEGINNING OF JPM PERFORMANCE.

Initial Conditions: Normal plant monitoring in progress.

Initiating Cues :

Perform 0-6.13 Attachment I Channel Checks and Instrument Verification

25-May-2006 Job Performance Measure Exam Page: -- . -3. I Description: 0-6.13 Daily Performance Logs Attachment (JR341.002)

JPM Tasks Task ID: 119-009-03-01B

Task Standards :

Identify switch, meter or component out of required position or band.

Tools :

Terminating Cues

Task Completion

References :

ID - PRO 0-6.13

- , --

Description

DAILY SURVEILLANCE LOG

Safetv Considerations

Consequences of Inadequate Performance: Tech Spec Violation

General Comments :

Review Date Ref Flag

0

1) Setup the Simulator at any 100% power IC 2) Insert MALF PZR3A, 43% 3) Verify >5% deviation between LT-426 and the other channels 4) Fill out 0-6.13 Attachment I for the last RWST visual check 7/16/06 92%

I 1

P I Page: Job Performance Measure Exam -- 25-May-20 0 6

-' Performance Checklist

1 Element : Conditions : Standards : Review 0-6.13 Attachment I CUE: give attachment to examinee Same as element

Comments :

Satisfactory 0 Unsatisfactory 0 2 Element : Conditions :

Perform Attachment I per procedure

Standards : Locates meters verify parameters are within operability bands and complete Attachment I signoffs

Comments :

Satisfactory 0 Unsatisfactory Element : CRITICAL Conditions : Recognize that LT-426 is outside the acceptance band

Standards : Locates LT-426. Determines that the instrument is inoperable per 0-6.13 and SR3.3.1.1

Comments :


4 Element : Notify the CRS or SM

~~~

Conditions : Standards : CUE: No Further Actions Same as Element

Comments :


I , Page: 5 I 25-May-2006 Job Performance Measure Exum - -

I

..-l)M Ouestions

Question

Answer

References


I 1

-l. I Page: Job Performance Measure Exam _- 25-May-2006 .-..../’

JPM NO JR343.005

Control of LCO’s for Equipment Out of Service

Revision #: 0


Location: Simulator


Candidate:

Evaluator:

Actual Time: -4


Trainee:

Instructor:

Submitted By Date

Reviewed By Date

P I I 25-May-2006 Job Performame Measure Exam -- Page: I 1

NOTE


Initial Conditions: Plant is at 55% power, Mini-Purge is not in service, no other equipment has an A-52.4 submitted on it.

Initiating Cues :

Shift Supervisor requests MOV-852A be deemed inoperable and asks you to fill out an A-52.4 to declare the component inoperable. The equipment will be inoperable due to the breaker being found tripped and cannot be reset. Required testing for operability will be determined after investigation of the problem. Use present date and time for when the component is to be deemed

- inoperable.

3 I Page: Job Performance Measure Exam -- 25-M~~~-2006 -’ Description: Complete a A-52.4 Limiting Conditions for Operablity Evaluation (JR343.005)

JPM Tasks

Task ID: 300-003-01-01A

Task Standards :

Correctly determine the allowable time out of service for a single component.

Tools :

Terminating Cues

Task Completion Trainee Says Task is Completed

References :

ID - I

PRA A-52.4

TECHSP ITS 3.5.2

DescriDtion Review Date Ref Flag

CONTROL OF LIMITING CONDITIONS OF OPERATIONS ECCS - MODES 1,2, and 3

0



General Comments :

Component Inoperable is the B train of ECCS Tech Spec. 3.5.2

I I

4 I Page: Job Performance Measure Exam -- 25-May-2006 v’


1 Element : Obtain a controlled copy of A-52.4

Conditions : Standards : CUE: Give Examinee copy of the procedure

Same as Element

Comments :

Satisfactory 0 Unsatisfactory 0 2 Element : Conditions :

Fill in EIN, Date, and Time complete step 3.2.1

Comments :

Standards : Same as element

Satisfactory Unsatisfactory 0 3 Element : Conditions :

Determine Plant mode and complete step 3.2.2

- Comments: Satisfactory

Standards : Plant Mode is Mode 1

Unsatisfactory u *4 Element: CRITICAL Conditions :

Determine Tech Spec Section and fill in step 3.2.3

Comments :

Satisfactory u

Standards : Enter corect T.S. in 3.2.3. Tech Spec Section 3.5.2 ECCS Modes 1-3

Unsatisfactory

5 Element : Conditions : Perform Loss of Safety Function Screening per Attachment I1 fill in step 3.2.4

Comments :

Satisfactory

Standards : Determines that no loss of safety function exists

Unsatisfactory 0 u - Element : Conditions : Standards :

Records EOOS PFS and System Colors complete step 3.2.5

CUE: Colors are both Green Records Colors

- - 5. I Page: Job Performance Measure Exam 25-May-2 006

Comments : u-

Satisfactory 0 Unsatisfactory 0 *7 Element: CRITICAL Conditions : Standards :

Determines Required Action time from T.S. 3.5.2 complete step 3.2.6 operable (Table 3.5.2-1)

Go To T.S. 3.5.2 Determine that A Train is

Determine Reqired action time from 3.5.2A 72 hours to restore Record in step 3.2.6

Comments :

Satisfactory 0 Unsatisfactory *8 Element: CRITICAL Conditions :

Determines Required Action time not met from T.S. 3.5.2 complete step 3.2.13

CUE: No further actions Standards : Go to 3.5.2B record time in step 3.2.13 Mode 3 in 6 hours Mode 4 in 12 hours

Comments :

Satisfactory 0 Unsatisfactory 0 JPM Questions

Question

Answer

References


I 1

-l. I Page: Job Performance Measure Exam -- 25-May-2006 I 1 v

JPM NO JC119.001

Complete EPIP 1-5 Status Report (PPCS no avalible)

Revision #: 0


Location: Simulator


Candidate:

Evaluator:

-.- Actual Time:


Trainee:

Instructor:

Submitted By Date

Reviewed By Date


25-May-2006 ~

.--' NOTE


Initial Conditions: The Plant was at 100% power when a LOCA occured. An Alert was declared and the Initial notification has been made per EPIP 1-5. The PPCS has failed and the TSC is unable to complete status reports for transmittal. The communicator is currently busy making followup notifications.

Initiating Cues :

The Shift Manager directs you to complete and transmit the plant status report per EPIP 1-5 Attachment 3e.

r 1

-- - - 3.1 Page: Job Performance Measure Exam 25-May-2 006

L- Description: Complete EPIP 1-5 Status Report (PPCS 00s) (JC119.001) JPM Tasks

Task ID: 1 19-007-03-0 1A

Task Standards :

Correctly complete EPIP 1-5 Attachment 3e data sheet.

Tools :

Terminating Cues

The Data sheet is correctly completed

References :

- ID Description PREPIP EPIP 1-5 NOTIFICATIONS


CI


Consequences of Inadequate Performance: Failure to correctly complete the required data sheet will result in the TSC & EOF being unable to assess plant conditions. This results in an inability of those organization to provide the need support the the Control Room and to protect the public.

General Comments :

Setup the Simulator to any at Power IC. Insert a 5000 gpm LOCA and complete E-0. Freeze simulator and record EPIP 1-5 Attachment 3e data for the key.

-- . - 4 1 Page: Job Performance Measure Exam 25-May-2006

u. Performance Checklist

1 Element : Conditions : Obtain EPIP 1-5 Procedure and review attachment 3e

Comments :

Satisfactory 0

Standards : Obtain Procedure Determine that Attachment 3e must be performed

Unsatisfactory 0 *2 Element: CRITICAL Conditions :

Obtain Data for Attachment 3e from the Control Room indications.

~

Standards : Locates MCB indicators and records Data on the attachment

Comments :


** Element: CRITICAL Conditions : Standards : Transmitts the attachment to the TSC or telephone

Comments :

CUE: No further actions Transmits to the TSC via Fax L

Satisfactory 0 Unsatisfactory c] JPM Questions

Question

Answer

References


I I

-l. I Page: Job Performance Measure Exam -- 25-May-2006 \-

JPM NO JS345.001

Respond to a Hazardous Chemical Spill

Revision #: 0


Location: In Plant


Candidate:

Evaluator: . . ----

Actual Time:


Trainee:

Instructor:

Submitted By Date

Reviewed By Date

I I

Page: Performance Measure Exam --

25-iMry-2006

I J

d'

NOTE

THE EVALUATOR WILL EXPLAIN THE JPM INITIAL CONDITIONS AND PROVIDE CLARIFICATION AS REQUIRED. THE EXAMINEE MAY USE ANY CONTROLLED COPY REFERENCES THAT ARE NORMALLY AVAILABLE IN THE CONTROL ROOM, INCLUDING LOGS. MAKE ALL WRITTEN REPORTS, ORAL REPORTS, AND LOG ENTRIES AS IF THE EVOLUTION WAS ACTUALLY BEING PERFORMED. THE EVALUATOR WILL BE TAKING NOTES, ASK FOR CLARIFICATION OF JPM REQUIREMENTS PRIOR TO THE BEGINNING OF JPM PERFORMANCE.

Initial Conditions: The plant is operating durring normal conditions 100% power. Dayshift Midweek. You are the Shift ,Manager.

Initiating Cues :

The Stockroom notifies you that they were transporting 2 barrels of Hydrazine from the Warehouse to the Turbine Building. While decending the hill near the Outside Condensate Storage tank one of the barrels fell off the pallet and is leaking.

I I

-3. I Page: Job Performance Measure Exam -- 25-May-2006 'y Description: Respond to a Hazardous Chemical spill

JPM Tasks

Task ID: 345-001-05-03A

Task Standards :

Implement IP-ENV-3 to contain the spill and notify appropriate responders.

Tools :

TerminatinE Cues

Task Completion

References :

ID - PRIP IP-ENV-3

L-

Descrbtion Review Date Ref Flag

RESPONSE TO A SPILL OF HAZARDOUS MATERIAL/WASTE


Consequences of Inadequate Performance: Failure to mitigate the effects of a Chemical Spill result in an increase in risk to plant personnel and the public.

General Comments :


25-May-2006 ~

W-

1

*2

*3

--.


Element : Conditions : Obtain Copy of IP-ENV-3. Go to the spill response section

Comments :

Standards : Same as Element

Satisfactory Unsatisfactory Iz]

CRITICAL Conditions : Standards : CUE: Announcement is made.

Element : Announce spill over PA system Makes the announcement or

direct operator to make the annoucement

Comments :

Satisfactory 0 Unsatisfactory 0 Element : CRITICAL Conditions : Dispatches Personnel to evaluate the spill.

CUE: Personnel Contacted

Note: Give the following Cue to the SM after the evaluator has been dispatched.

Standards : Contacts one of the following to evaluate the spill:

-Chemical Control Coordinator -Safety Group -Chemistry Group

-NLO

CUE: The spill evaluator reports the following; 1. The barrel split open spilling 112 its 35 gal contents. 2. Some of the contents ran into the storm drain located North of the outside CST. 3. The Forklift operator breathed in fumes from the chemical and is feeling ill, he is now in the TSC. 4. The material involed is SCAVOX 35% Hydrazine. 5. The HazMat Coordinator is on scene attempting to contain the spill.

Comments : -.


-- - - 51 Page: Job Performance Memure Exam 25-May-2006 -/ Element: CRITICAL Conditions : Standards :

Announces a Medical Emergency Note: When the Medical Announcement is made give the following cue. CUE: The CRS is refering to A-7 "Handling Injuries and Medical Emergencies'' and the associated notifications

Make or Direct annoucement for Medical Response team to report to the TSC

Comments :

Satisfactory 0 Unsatisfactory [7 * 5 Element: CRITICAL Conditions :

Determines that the spill is major

Comments :

Satisfactory 0

Standards : Determine that per attachment 1 and step 3.3.3 A. 2. that the spill is major.

Unsatisfactory ~ ~

Element : CRITICAL Conditions : Perform Major spill action (not previously done) the Response coordinator-

CUE: When notification made to

MaryEllen Dangler has been notified and is acting as Coordinator and Enviromental response team leader.

Comments :


Standards : Obtains MSDS sheet for the chemical Completes Attachment 2 Notifies the Response coordinator and Enviromental staff

0 7 Element : Conditions : Standards :

Evaluate the spill for EPIP 1-0 reporti bility critera was exceeded

Comments :

CUE: No Further Actions Detemine that no classifiction


Page: 1 I 25-May-2006 Job Performance Measure Exam -- ~

JPM NO JS343.006

Loss Of Safety Function Determination

Revision #: 0


Location: Classroom


Candidate:

Evaluator:

. . --- Actual Time:


Trainee:

Instructor:

Submitted By

Reviewed By

Date

Date

Page: 2 Pmformance Measure Exam --

25-MUY-2006 ~

V'

NOTE


Initial Conditions: 100% Power normal operations. The following equipment is 00s "D" SW pump "B" CNMT Recirc Fan MOV 852A

Initiating Cues :

The MCC 1D Supply Breaker trips and cannot be reset. MCC 1D is deenergized. What action must be taken per Tech Specs? -

1

- - I Page: Job Performance Measure Exam -- 25-May-2 006 -2- Description: Loss of Safety Function Determination

JPM Tasks

Task ID: 300-003-03-02C

Task Standards :

Correctly Identify that a loss of Safety Function Exists

Tools :

Terminating Cues


References :

ID - PRA A-52.4

TECHSP ITS 3.5.2 TECHSP ITS 3.6.6

TECHSP ITS 3.7.8 TECHSP ITS 3.8.9

Description

CONTROL OF LIMITING CONDITIONS OF OPERATIONS

Containmen Spray (CS), Contaiment Recirculation Fan Cooler (CRFC), NaOH, and Containment Post-Accident Charcoal Systems Service Water System Distribution Systems - MODES 1,2,3, and 4

ECCS - MODES 1,2, and 3




CI 0

General Comments :

I I

4 I Page: Job Performance Measure Exam -- 25-May-2006 --.


1 Element : Conditions : Obtain Copy of Tech Specs and A-53.4

Standards : Same As Element

Comments :

Satisfactory Unsatisfactory 0 *2 Element: CRITICAL Conditions :

Per TS 3.8.9 determine that "B" train of AC power Dist is inoperable

Comments :

Satisfactory


Unsatisfactory c] 3 Element : Conditions :

Fill out A52.4 steps3.2.1-3.2.3

-- Comments :

Satisfactory


Unsatisfactory c]

*4 Element: CRITICAL Conditions : Perform Saferty Function evaluation (per Attachment 11)

Comments :

Satisfactory

Standards : Evaluate 00s equipment 1) SW pump D- Not in SW spec. therefore 3.8.9 gives guidence 2) "B" Recirc Fan All other fans have normal power supplies therefore do not have a loss of safety function. 3 ) MOV 852A, MCC 1D supplies MOV 852B therefore both trains of RHR are incapable of injection and inoperable.

Unsatisfactory c]

Page: 5 Job Performance Measure Exam - . -

25-May-2006

..-. Element: CRITICAL Conditions : Determine both trains of SI iooperable enter TS 3.5.2B which directs to TS 3.0.3

Cue: No further actions

Comments :

Satisfactory


Unsatisfactory

JPM Questions

Question

Answer

References


1 I

-l. I Page: Job Performance Measure Exam -- 22-Mi~y-2 006

JPM NO JS119.0Oi

Verify Equipment Tagout Boundary

Revision#: 0


Location: Classroom


Candidate:

Evaluator:

*. - Actual Time:


Trainee:

Instructor:

Submitted By Date

Reviewed By Date

22-May-2006 Job Performance Measure Exam Page: -- 2. I 1,.

NOTE

THE EVALUATOR WILL EXPLAIN THE JPM INITIAL CONDITIONS AND PROVIDE CLARIFICATION AS REQUIRED. THE EXAh4INEE MAY USE ANY CONTROLLED COPY REFERENCES THAT ARE NORMALLY AVAILABLE IN THE CONTROL ROOM, INCLUDING LOGS. MAKE ALL WRITTEN REPORTS, ORAL REPORTS, AND LOG ENTRIES AS IF THE EVOLUTION WAS ACTUALLY BEING PERFORMED. THE EVALUATOR WILL BE TAKING NOTES. ASK FOR CLARIFICATION OF JPM REQUIREMENTS PRIOR TO THE BEGINNING OF JPM PERFORMANCE.

Initial Conditions: Condensate transfer pump (PCD04) requires pump bearing replacement.

Initiating Cues :

The SM has requested you review the completed Isolated Work Area Request (A- 140 1, Figure 1) for isolating the Condensate Transfer Pump (PCD04) to veri@ work area boundaries.

:. I Page: Job Performance Measure Exam -- 22-May-2006

Description: Review Isolated Work Area Request(JS 1 19.001) b..

JPM Tasks

Task ID: 342-004-03-02A

Task Standards :

1) Determine adequate boundary exists 2) Determine inadequate boundary exists

Tools :

P&ID 33013-1234

P-12

Terminating Cues

Trainee Says Task is Completed Task Completion

v

References :

ID - PROPSA A-1401 PRP P-12

Description

STATION HOLDING RULES ELECTRICAL SYSTEMS PRECAUTIONS, LIMITATIONS, AND SETPOINTS


Consequences of Inadequate Performance: Personal Injury

Equipment Damage

General Comments :


0 0

Provide P&ID and A-1401 Figure 1 to student. Incorporate errors on A-1401 Figure 1 if it is desired to exercise Option 2.

d'

Page: 4 Job Performance Measure Exam - -

22-May-2006

v Performance Checklist

1 Element : Review Isolated Work Boundary.

Comments :

Satisfactory

~~

Conditions :

0 Unsatisfactory 0

Standards : Same as element.

*2 Element: CRITICAL Conditions : Standards : Option 1 - Boundary is adequate. Option 2 - Boundary is not adequate.

CUE: No further actions Option 1 - Determines no errors in boundary. Option 2 - Determines and reports errors in boundary. V-4046 needs to be closed.

Comments :

Satisfactory 0 Unsatisfactory 0 M Questions ._

Question

Answer

References


-: I Page: Job Performance Measure Exam -- 25-May-2006 U’

JPM NO JS341.002

Approve Liquid Release per CH-RETS-LIQ-REL (JS341.002)

Revision #: 1


Location: Classroom


Candidate:

Evaluator:

Actual Time: I


Trainee:

Instructor:

Submitted By Date

Reviewed By Date

25-May-2006 Job Performance Measure Exam Page: -- -: I -'

NOTE

THE EVALUATOR WILL EXPLAIN THE JPM INITIAL CONDITIONS AND PROVIDE CLARIFICATION AS REQUIRED. THE EXAMINEE MAY USE ANY CONTROLLED COPY REFERENCES THAT ARE NORMALLY AVAILABLE 'IN THE CONTROL ROOM, INCLUDING LOGS. MAKE ALL WRITTEN REPORTS, ORAL REPORTS, AND LOG ENTRIES AS IF THE EVOLUTION WAS ACTUALLY BEING PERFORMED. THE EVALUATOR WILL BE TAKING NOTES. ASK FOR CLARIFICATION OF P M REQUIREMENTS PRIOR TO THE BEGINNING OF JPM PERFORMANCE.

Initial Conditions: The operating crew is preparing to release a Monitor Tank.

Initiating Cues :

You are the Shift Manager and are required to review a release form prior to making a Liquid Release of the Monitor Tank per CH-RETS-LIQ-REL "Liquid Waste Release" Figure V

I 1

-: I Page: Job Performance Measure Exam -- 25-May-2006 Description: Approve Liquid Release per CH-RETS-LIQ-REL (JS341.002)

JPM Tasks Task ID: 341-012-03-03A

L’

Task Standards :

Detects errors in the permit and does not approve the permit until corrected.

Tools :

Terminating; Cues

Task Completion

References :

- ID Descrbtion PRCH CH-RETS-LIQ-REL LIQUID WASTE RELEASE


Consequences of Inadequate Performance: Exceeding Release rate for a Liquid Release

General Comments :


CI

Complete a CH-RETS-LIQ-REL Attachment V for pre release condition. (May obtain RP assistance) compete pre release parts correctly except @r the sample time being >12 hour prior to the start of the release.

I Page: 4

Job Performance Measure Exam - 25-May-2006

-

--. Performance Checklist

Conditions : Standards : Same as element

1 Element : Reviews CH-RETS-LIQ-REL form.

Comments :

Satisfactory 0 Unsatisfactory 0 *2 Element: CRTTICAL Conditions :

Evaluate Attacment V for correct Data

Standards : Determines the form is incorrect in that the release time is outside the allowable time permited. (> 12 hours since the sample time)

Comments :

Satisfactory Unsatisfactory [7

Element : Conditions : Standards : --/ Determine that sample must be Cue No further actions Same as element.

redone

Comments :


JPM Ouestions

Question

Answer

References


Page: Job Performance Measure Exam --

2 5-May-2 006

-’

Event Classification

Revision #: 0


Lo cation: Simulator

Estimated Time (minutes):

JPM NO JS340.021

15.00

Candidate:

Evaluator:

Actual Time: --


Trainee:

Instructor:

Submitted By

Reviewed By

Date

Date

I I

_- . - 21 Page: Job Performance Measure Exam 25-May-2006

NOTE

THE EVALUATOR WILL EXPLAIN THE JPM INITIAL CONDITIONS AND PROVIDE CLARIFICATION AS REQUIRED. THE EXAMINEE MAY USE ANY CONTROLLED COPY REFERENCES THAT ARE NORMALLY AVAILABLE IN THE CONTROL ROOM, INCLUDING LOGS. MAKE ALL WIUTTEN REPORTS, ORAL REPORTS, AND LOG ENTRIES AS IF THE EVOLUTION WAS ACTUALLY BEING PERFORMED. THE EVALUATOR WILL BE TAKING NOTES. ASK FOR CLARIFICATION OF JPM REQUIREMENTS PRIOR TO THE BEGINNING OF JPM PERFORMANCE.

Initial Conditions: The plant experienced the events of the just concluded scenario.

Initiating Cues :

Classify this event at the highest required classification per EPIP 1-0.


25-May-2006 -

u Description: Event Classification for the 2006 Initial License exam (JS340.02 1)

JPM Tasks

Task ID: 340-001-05-02N

Task Standards :

Classify per the Nuclear Emergency Response Plan

Tools :

Terminating; Cues


References :

ID - - PREPIP EPIP 1-0

Description

GINNA STATION EVENT EVALUATION AND CLASSIFICATION



Consequences of Inadequate Performance: Failure to correctly Classify the event leads to the Failure to correct implement the Emergency plan, resulting in a unnecessary threat to the health and safety of the public.

General Comments :

The JPM is designed to be used with the 2006 Initial NRC License Exam.

1 I

. - 41 Page: Job Performance Measure Exam 25-May-2006 d'


1 Element : Conditions : Obtain copy of EPIP 1-0

Comments :

Satisfactory

Standards : May use Procedure or Wall Chart

Unsatisfactory 0 ~~

*2 Element: CRITICAL Conditions : Standards : Correctly determine Classification CUE: No futher actions Scenario 06- 1 - 1

Alert based on RCS Leakage >46 gpm EAL 3.1.2 Scenario 06- 1-2 SAE based on Faulted Ruputed S/G EAL 4.2.1 Scenario 06-1 -3 Alert Based on RCS Leakage > 46 gpm EAL 3.1.2

Comments : -'

Satisfactory Unsatisfactory 0 JPM Questions

Question

Answer

References


i job performance measure exam page: -- -i. ii 25-may-2006 job performame measure exam -- p i page:...

Documents