ice reles manuales np 800 guia utilizador software smartsoft 443f (ingles)

User Guide SMARTsoft Issue: F File : A443 Print : 05/07/2011

Date : 06/2011

This document is the sole property of ICE. No duplication nor release to third party is allowed without prior authorization

USER GUIDE

SETTING SOFTWARE

SMARTSOFT

ICE - 11, rue Marcel Sembat - 94146 ALFORTVILLE CEDEX - France TEL. : +33 1 41 79 76 00 - FAX : +33 1 41 79 76 01 E-MAIL : [email protected]

WEB SITE : www.groupeice.com

Folio : 1 This document is the sole property of ICE. No duplication or release to third party is allowed without prior authorization.

User guide SMARTsoft

Date : 06/2011 Print : 05/07/2011 Issue : F

FOREWORD

The aim of this handbook is to provide to the User, the necessary informations for the use of the setting software SMARTsoft (Setting Maintenance Analysis Recording Timesaving soft), common to the whole of Industry, Railway, Transport, Regulation and Distribution ranges.

We advise you to read it carefully, in order to take note of the available functionalities and to proceed to connection and power of the product in accordance with the recommendations provided in the Handling Guide.

The setting software can be used as followed: Either in not connected mode to device, allowing a file preparation before the

configuration or the operation of files loaded from the product. Or in connected mode, allowing the configuration and the questioning of the device as

well as the loading of files.

In the connected mode to device, all functions of configuration, commissioning, real-time display, consultation of consigned events or disturbance recordings are accessible from the software menus.




CONTENTS

1. Configuration of the PC ............................................................................................... 4 1.1 Required configuration ................................................................................................................ 4 1.2 Setup of the software................................................................................................................... 4 1.3 Start-up of the software ............................................................................................................... 6 1.4 List of main menus ...................................................................................................................... 9

2. Editing Menu................................................................................................................11 2.1 Preferences ............................................................................................................................... 11

3. File Menu .....................................................................................................................12 3.1 Addition or update of the databases of the equipments............................................................ 12

3.1.1 Function Add, update of the bases: ................................................................................ 13 3.1.1.1 Button List dir. Data..................................................................................................... 13 3.1.1.2 Button Base(s) Import selected................................................................................... 14

3.1.2 Function Delete bases................................................................................................... 15 3.2 Create a configuration file.......................................................................................................... 16

3.2.1 Choice of options and alternatives .................................................................................... 17 3.3 Open a configuration file............................................................................................................ 17 3.4 Save the configuration of a device in a file................................................................................ 18 4. Parameter Menu ..........................................................................................................19 4.1 Parameters and associated values ........................................................................................... 20 4.2 Introduction to the screens ........................................................................................................ 23

4.2.1 Category: Informations ..................................................................................................... 23 4.2.2 Category: Operation .......................................................................................................... 24 4.2.3 Category: Protection.......................................................................................................... 25 4.2.4 Category: LEDS................................................................................................................. 26 4.2.5 Category: Inputs ................................................................................................................ 27 4.2.6 Category: Outputs.............................................................................................................. 28 4.2.7 Category: Communication ................................................................................................. 29 4.2.8 Specific management according to the device.................................................................. 30

4.2.8.1 PDZI-800 Protection ...................................................................................................... 30 4.3 Transfer a configuration file to a device .................................................................................... 32 4.4 Comparison ............................................................................................................................... 32 4.5 Print the configuration of device ................................................................................................ 34 5. Read Menu...................................................................................................................35 5.1 Real time measures sub menu.................................................................................................. 35

5.1.1 Choice buttons of measures or accessible states ............................................................. 37 5.1.1.1 Category: Measures ...................................................................................................... 37 5.1.1.2 Category: Operation information ................................................................................... 38

5.1.2 Category: Real time states ................................................................................................ 39 5.1.3 Category: Memorized states.............................................................................................. 40 5.1.4 Category: Counters ........................................................................................................... 41 5.1.5 Remote control management ............................................................................................ 42 5.1.6 Category: Status ................................................................................................................ 42 5.1.7 Category: Counters ........................................................................................................... 42

6. Commissioning menu.................................................................................................43 6.1 Screen test sub-menu ............................................................................................................... 43 6.2 LCD contrast sub-menu............................................................................................................. 43 6.3 Time-setting sub-menu.............................................................................................................. 44 6.4 Commissioning help sub-menu ................................................................................................. 44

6.4.1 Output units tests............................................................................................................... 45




6.4.2 Wiring control..................................................................................................................... 46 6.4.3 Thresholds control ............................................................................................................. 47

6.4.3.1 Thresholds control with Bar-Graph management [59][27][81] .................................. 48 6.4.3.2 Thresholds control of power [32P][32Q] [37P][37Q] ................................................. 49 6.4.3.3 Thresholds control of the Cosinus [55] and the Tangent Phi [Q/P] ............................... 50 6.4.3.4 Thresholds control of the loss of excitation [40] ............................................................ 51 6.4.3.5 Thresholds control of the Directional function [67] [67N] .............................................. 52 6.4.3.6 Thresholds control of mini of impedance [21] and directional [32] functions ................ 53

7. Events menu................................................................................................................55 7.1 Memorization/Acknowledgement............................................................................................... 55 7.2 Detail of an event....................................................................................................................... 56

8. Disturbance menu.......................................................................................................57 8.1 Reading of protection sub-menu ............................................................................................... 57 8.2 File reading sub-menu............................................................................................................... 58 9. Help menu....................................................................................................................61 9.1 Password modification:.............................................................................................................. 61 9.2 Display of the software version.................................................................................................. 62 10. Attachments.............................................................................................................63 10.1 Device connection: .................................................................................................................... 63




1. Configuration of the PC This chapter describes the basic operations of use of the software, like the setup, the files management or the printings. The stages described in this first paragraph are identical for all the relays of the NP800 range.

1.1 Required configuration

The configuration software is for PC respecting the following configuration: Windows 98, NT2000 or XP, VISTA, Seven, 1 hard drive of at least 50 Mo available, 1 CD-ROM reader, 1 VGA screen with a minimum resolution of 1024*768, Communication port

- Either a RS232 port - Or an adapter USB-RS322 with corresponding driver.

1.2 Setup of the software

From the installation CD, run: install Choose the language used by the setting software:

The program of installation creates by default the directory C:\Groupe ICE\SMARTsoft as specified below.




If the directory fits, click on the Next button, otherwise, click on the button which opens a selection window for the destination directory. Warning for Windows, VISTA or Seven, you must not install the software in Program Files directory.

By clicking the Next button, the setting software SMARTsoft is installed in the selected directory.




The last screen indicates the end of the installation with the possibility to execute the program.

If Run the program stays selected, the program is launched after clicking on the button Done. Otherwise, from the icon SMARTsoft" installed to the desktop, launch the program of the setting software.

After the first installation, import the data base of the equipments to be configured from the CD supplied. Report to the paragraph Addition or update of the bases of the equipments of this guide.

1.3 Start-up of the software

An identification screen of the user is displayed.




Enter your password corresponding to the user chosen.

The different user profiles and their password by default are following: "Commissioning": "mes" "Operation": "exp" "Consultation": " "

Every type of user has different access rights. Consultation allows only the display of the parameters and measurements Operation

- idem profile of Consultation - Modification of the parameters - Remote orders

Commissioning - idem profile Operation - The commissioning menu

- Activation of the output units - Etc

The user's password can be customized in the Help, Modification of password window:




Then the main screen is displayed.




1.4 List of main menus

The different functions are grouped per menus: File Menu:

Management of different files: New, Open, Close, Save, Save as. Management of the printing: Printing configuration, print. Management of the DataBases.

Edit Menu: Management of preferences Access to parameters

RTM Menu: Real time measures (measures, Input state, relay state, state of the protection functions, counter values, etc.).

Commissioning Menu: Help for commissioning and maintenance of the protection (LCD test, contrast tuning, time setting, output testing, wiring control, thresholds control).

Events Menu: reading of the device log, reading of a saved events file Disturbances Menu: reading of devices disturbances, reading of disturbance file

recorded Help Menu: Display of the setting software issue.

The buttons allow reaching directly some functions:

New Button: Create a new configuration

Open Button: Open a previously archived configuration.

Close Button: Close current configuration.

Compare Button: Compare a file with the current configuration.

Save Button: Save the current configuration.




Print Button: Display of the current configuration before printing.

Manage DB Button: Addition or update of the databases of the equipments

Connect Button: Connection to the device and reading of parameters.

Upload Button: Writing of the current configuration in the device

Parameters Button: Display of the device parameters.

RTM Button: (Real Time Measurements) Display of the measure variables, counters, state of the device.

Events Button: Display of the events occurred in the device.

Disturbances Button: Display of the disturbance recordings executed by the device

Disconnection Button (located at the bottom of the screen): Device disconnection




2. Editing Menu

2.1 Preferences

Select the EDIT menu, then the PREFERENCES sub menu. Multiple choices are proposed to the operator:

Choice of the HMI language.

Choice of Setting display mode o Packed: Only the titles of the parameters functions zone are initially

displayed. o Expanded: All the parameters of the group are initially displayed.

Choice of the communication port:

Operator has a list of usable communication ports to interact with the device. Note: These ports can be used by USB or network adapters. In this case, the driver has to be installed to the PC and the adapter connected to it has to be shown in the list of available ports.

To communicate with a device, connect the linkage cable between the RS232 plug of an NP800 device and the RS232 output corresponding to the COM port selected (Local on PC, deported by USB).




3. File Menu

3.1 Addition or update of the databases of the equipments

This action is possible only in not connected mode and without open configuration file.

1 - Select the menu FILE, then the submenu MANAGE BASES

The operator activates the function Add, updated bases or deletes the bases.




3.1.1 Function Add, update of the bases:

The button List dir. Data allows the update of a set of bases of several equipments. (directory "DATA" of SMARTsoft or from the CD) The button List a/the base(s)" allows the update of base(s) of equipment. 3.1.1.1 Button List dir. Data After clicking the button List dir. Data the following screen is displayed. The operator must selects the directory "DATA" of SMARTsoft or from the CD

The selection of the directory validates the button Base(s) Import / selected ". The operator chooses the bases to be imported and confirms the import by action on the button Base(s) Import / selected ".




3.1.1.2 Button Base(s) Import selected Clicking on the button "Base(s) Import selected", the following screen is displayed. The operator selects the base to be added or to be updated.

The selection of the file validates the button "Base(s) Import selected ". The operator chooses the bases to be imported and confirms the import by action on the button Base(s) Import / selected".




3.1.2 Function Delete bases

The operator selects the bases (in column "Version") to delete.

The button "Base(s) delete" removes the selected databases. The button "Cancel" cancels the selection of the bases.




3.2 Create a configuration file

This action is possible in not connected mode. 1 - Select the menu FILE, then the submenu NEW

2 - Choose the family, the equipment, and then eventually, the version of the equipment




3.2.1 Choice of options and alternatives

1 - Select the case of your equipment, according to the supplied version / or the diagram n:

2 - Select the options and alternatives of your device, according to the supplied configuration:

3 - Validate your choice. The window of the parameters is displayed.

3.3 Open a configuration file

1 - Select the FILE menu, then the OPEN sub menu. A selection window is displayed.

2 - Select the directory, then the file to be opened and select . Then, the File parameters window is displayed.

Directory location

Files location




3.4 Save the configuration of a device in a file

1. Select the FILE menu, then the SAVE AS sub menu. A window of selection is displayed.

2. Enter the FILE NAME to save, and then validate . The file is saved.

Directory location

Files location




4. Parameter Menu

This window allows programming the whole of device parameters, classified by categories associated to an icon.

Icon Category

Informations

Operation

Protection

Programmable functions

LED

Digital Inputs

Digitals Outputs

Communication

Regulation

Logical Selectivity

Disturbance

Inhibition

Note: The categories depend on the type of the selected device. The list of icons above is not exhaustive.




4.1 Parameters and associated values

After a selection of a category, the list of functions of this category appears in the table. By packing / expanding the functions, the parameters are displayed in the table. For every parameter, the description and the affected value of every set are displayed. The modified values by the operator are displayed in red.

Example: - Zone of packed functions, symbolized by +.




- Zone of the expanded functions, symbolised by -A function is expanded by clicking with the mouse on +. Return to the packed mode by clicking on -.

- Parameter modification of one function via a combo, in a data input zone, an elevator.

Before the modification, all informations of the parameters are displayed in black. Modification via a combo:

Modification via a data input zone or an elevator.

- The modified parameters are displayed in red.




- When all the modifications of the functions are done, click on the button in order to store them in the base. The red parameters become default colours, and the expanded levels close.

- The button allows reloading either the initial value, or the last validated value.




4.2 Introduction to the screens

The different parameters are classified by categories, then by functions. These categories and functions depend on the device type to configure.

Refer to the Application guide of the device to be configured to obtain a detailed list of the available functions and their setting.

4.2.1 Category: Informations

This category allows displaying the generic informations of the device.




4.2.2 Category: Operation

This category allows displaying or modifying the configuration of the device general parameters, for example:

Nominal (rated) voltage Name of the sub/station, device, device number Definition of the different sensors




4.2.3 Category: Protection

This category allows displaying or modifying the configuration for the whole of the device functions such as:

Max I dI / dt Max U Min U Max F Recloser

The example below shows the protection functions of NPW800.




4.2.4 Category: LEDS

This category allows defining the assignment of LEDS on the front side of the device. Two parameters by LED allow defining the associated function and the display mode:

Definition of the function associated to the LED Display mode on signal:

o Fix, o Flashing

Display mode on fault: o Inst. Fault Fix o Inst. Fault flashing o Inst-Flashing Trip-Fix o Inst-Fix Trip-Flashing o Trip Fix o Trip-Flashing




4.2.5 Category: Inputs

This category allows defining the association of inputs to the different device functions. The parameter "Operating mode of Digital Inputs" allows selecting the active status for each input.




4.2.6 Category: Outputs

This category allows defining the output assigned to the different functions: Output for the tripping of Circuit Breaker Output signalling a trip Output signalling the current table of parameters

Several informations can be assigned to the same output.




4.2.7 Category: Communication

This category, activated if the communication option is present, allows defining the parameters of the RS485 communication, like:

JBUS slave number Transmission format Transmission speed




4.2.8 Specific management according to the device

4.2.8.1 PDZI-800 Protection

According to the device, the button, appearing on the line of the function, allows the graphic representation of the setting of minimum of impedance [21] and directional [32] functions.




Drawing of minimum of impedance [21] and directional [32] functions

The screen is making of three different areas: - Definition of stages, the stage value is displayed when running the mouse on its wording - Display of the parameters drawing - Display management: Zoom of display mode (HV, LV) The possible actions for the operator are: - Change of SET, by action on the tabs in top of the screen called Set 1and Set 2, which carries out an updating of the threshold values according to the selected SET.

- Change of the threshold colour, by action on the button of each threshold. - Change of the display mode and Zoom, Choice of the type of plotting.




4.3 Transfer a configuration file to a device

If the device is connected, a button is active. Then, ask the transfer of the data to the device.

If the type of device, the variants (alternatives) and the options are compatible with the data in the memory, the transfer is done.

If the type of device is different, the connection is not accepted.

If the type of device is the same, but its variables or options are not compatible with the data in the memory, the transfer is aborted. The options and variants window appear to display those of the device. If the operator validates, the parameters in memory are updated with the options and variants of the device.

4.4 Comparison

During the editing of device parameters, an action on the button allows selecting a file to compare to the current editing parameter.




The display of differences is carried out by the one of two lines: - The first in black: Configuration in progress - The second in blue: File selected

If the parameters have any difference, only the parameters of the configuration in progress are displayed.

During the display of the comparison, the operator can modify the parameters of the configuration current editing. To display all the differences between the configurations, the operator has to display each category of parameter.

An action on the button cancels the current comparison. The screen displays the list of current editing parameter.




4.5 Print the configuration of device

From the window of parameters inputs, a click on the button opens the window of parameters to print. Many output options are available:

- A printing towards the printer configured by default. - An output towards a file in "PDF" format. - Printing of one page - Printing of the entire document.




5. Read Menu

5.1 Real time measures sub menu

This window is accessible by button. The RTM window is divided in two tables allowing displaying at same time:

- The whole of measurements or states of the device. - The remote control.

Screen without remote control:

Access to the remote control is made by the button:




Screen with remote control:




5.1.1 Choice buttons of measures or accessible states

The whole of measures or status of the device is classified by categories associated to an icon. The list of categories displayed depends on the type of device connected.

5.1.1.1 Category: Measures

This category allows displaying the different measurements to display on the RTM. Current Voltage

See previous image (screen without remote control)




5.1.1.2 Category: Operation information

This category allows displaying the different states of the device. General status Faults Operating mode




5.1.2 Category: Real time states

This category allows displaying the different states of the device. State of digital inputs State of output units State of instantaneous faults State of the delayed faults




5.1.3 Category: Memorized states

This category allows showing the various states memorized of the equipment. State of instantaneous faults State of the delayed faults




5.1.4 Category: Counters

This category allows displaying the values of the different counters of device. Reclosing counter Tripping counter




5.1.5 Remote control management

By selecting a line in the remote control zone, the possible actions are displayed. The operator has to choose the action to do and ask the transfer to the device.

Line Selection Possible actions Transfer to the device

Execution report

The remote control commands can be grouped by group:

5.1.6 Category: Status

This category Allows showing the various remote control commands Circuit breakers (Closing, tripping) Reset memorized alarm Operating mode

5.1.7 Category: Counters

This category Allows showing the remote control commands on counters. Reset counters




6. Commissioning menu This menu is to be used during the commissioning and during operating maintenance tasks.

6.1 Screen test sub-menu

The "Screen test" function allows controlling the screen and the lights of the device: - alternate lighting of the 16 characters on the two lines of screen. - flashing of L1, L2, L3 and L4.

Note: The watchdog led (WD) is not tested by this function.

6.2 LCD contrast sub-menu

The LCD contrast" function allows to set the screen according to the viewing angle compared to the operator.

Place the device "Viewing angle" cursor, Press on the Test button to verify the good contrast of the screen. Press on the Validate button to record the new setting.




6.3 Time-setting sub-menu

This screen allows setting the time of the device with the PC time. This time-setting is necessary for dating the events.

The time-setting of the device is done by the button.

6.4 Commissioning help sub-menu

This screen is available with Commissioning level. It allows to access to the different following functions according to the connected device.




6.4.1 Output units tests

This screen available with "Commissioning" level, allows verifying the wiring of the output relays of device. The number of relay depends on the device type (Number of the relays, options, variants). A click on the associated button of one output unit allows activating temporarily this one. .




6.4.2 Wiring control

This screen available, according to the device, with Commissioning level allows to access to the wiring control of analog inputs.

This screen allows the display of specific measure values, allowing to the software to determine if the analog inputs are correctly wired.




6.4.3 Thresholds control

These screens available, according to device with Commissioning level, allows the thresholds control.

There are many types of screen of thresholds control as:

- Bar-graph management, functions: [59][27][81] Etc - Power management, functions: [32P][32Q] [37P][37Q] Etc - Management of the Cosinus and Tangent Phi, functions: [55][Q/P] - Management of loss of excitation, function [40] - Management of Directional functions [67][67N] - Management of minimum of impedance [21] and directional [32] functions




6.4.3.1 Thresholds control with Bar-Graph management [59][27][81]

The screen is divided in two distinct areas:

The possible actions for operator are: Change of SET, by action on the tabs in top of the screen called Set 1and Set 2,

which carries out an updating of the threshold values and activate the set of device according to the selected SET.

Change of the threshold colour, by action on the button of each threshold.




6.4.3.2 Thresholds control of power [32P][32Q] [37P][37Q]

The screen is divided in four distinct areas: The list of thresholds Graphic display of thresholds and operating point Display of measurements Display management

There are four possible modes: - A vector (Line from the origin at operating point), - A point, - Point cloud (for every reading the operating point is displayed, without erase

the previous point), - Vector between points (for every reading the operating point is displayed, by

drawing a line between the new point and the previous point).




The display or not of the threshold, by action on the box to tick .




6.4.3.3 Thresholds control of the Cosinus [55] and the Tangent Phi [Q/P]

The screen is divided in three distinct areas: The list of thresholds Graphic display of thresholds and operating point Display of measurements








6.4.3.4 Thresholds control of the loss of excitation [40]

The screen is divided in four distinct areas: The list of thresholds Graphic display of thresholds and operating point Display of the measurement Display management











6.4.3.5 Thresholds control of the Directional function [67] [67N]

The screen is divided in three distinct areas: The list of thresholds Graphic display of thresholds and operating point Display of measurements








6.4.3.6 Thresholds control of mini of impedance [21] and directional [32] functions Screen of the function [21] mini of impedance

The screen is divided in four distinct areas: The list of thresholds Graphic display of thresholds and operating point Display of the measurement Display management










The display or not of the threshold, by action on the box to tick . Change of the display mode (HV, LV).

Screen of the directional function [32]

Possible actions of the operator are the same as previous screen.




7. Events menu

7.1 Memorization/Acknowledgement

The list of the memorized events in the device can be loaded via button.

The Information button allows displaying event detail (see chapter below). The Print button allows printing the list of events. The Refresh allows reading new events occurred since the last loading. The Save button allows recording the events. The Close button allows to exit from the event menu.




7.2 Detail of an event

The detail is obtained by double-clicking on the event or on the button.

Detail of event content: The source (Sub-station and device names) The event (The type) The datation:

The date of the event is displayed, the "Synchronous time" and Relative time meaning the synchronisation of the device.

The associated measures.

The List button allows returning to the events list. The Close button allows to exit from event menu.




8. Disturbance menu

8.1 Reading of protection sub-menu

This menu allows choosing the disturbance recording needed to be transferred towards the device for display. These data disturbance can be saved in a set of files in Comtrade format, for external use: Analysis, values extraction, reproduction with a test set.

The number of recorded disturbances in the device depends on its type. The Tripping menu allows starting a manual recording.




8.2 File reading sub-menu

Every saved file can be analysed without a connection to the device. The origin characteristics of the line are memorised in the information zone, accessible by

clicking on the button.




After loading, the line of the disturbance recording appears on the screen. The setting zone, on left, allows modifying the line presentation and the analog inputs assignment (high) and digital (low). The different lines can be printed ( button).

The setting options, on left of the disturbance recordings window, allow modifying the presentation of the lines:

"Settings": choice of background colour, Grid of the background or marking of time stamping points on the disturbance recording line.

"Analog inputs": selection of analog inputs (main line), selection of the line color. "Digital inputs": selection of digital inputs (at bottom of line), selection of the line

colour.

The selection of channels is done by rolling lists.

The colour selection is done by clicking in the corresponding case to open the window for the colours.

Some vertical bars can be placed to do time measures, which are displayed on the service line (t0, t1 and t1 - t0)




A click on the key allows modifying the time scale.

With the help of the mouse, select the starting point of zoom and slide the mouse until the end point of zoom. The selected zone appears in black, like on the picture below.

In the end of selection, the zoom is executed:

To cancel zoom, you have to click on the button.




9. Help menu

9.1 Password modification:

This window allows the password modification of the different profiles.

Choose the profile to modify, then type the old password and validate.

Type the new password and validate.

Confirm the new password and validate. The new password is validated.




9.2 Display of the software version

This window allows displaying the version of SMARTsoft software.




10. Attachments

10.1 Device connection:

The cable to be used between the device and the DB9 output points of a PC fitted with a RS232 port is as follow:

ice reles manuales np 800 guia utilizador software smartsoft 443f (ingles)

Documents