icom ic-m72 instruction manual
TRANSCRIPT
-
8/8/2019 Icom IC-M72 Instruction Manual
1/40
INSTRUCTION MANUAL
iM72
VHF MARINE TRANSCEIVER
This device complies with Part 15 of the FCCRules. Operation is subject to the condition thatthis device does not cause harmful interference.
-
8/8/2019 Icom IC-M72 Instruction Manual
2/40
-
8/8/2019 Icom IC-M72 Instruction Manual
3/40
-
8/8/2019 Icom IC-M72 Instruction Manual
4/40
FOREWORDThank you for purchasing this Icom radio. The IC-M72 VHF MA -RINE TRANSCEIVER is designed and built with Icoms state of theart technology and craftsmanship. With proper care this prod-uct should provide you with years of trouble-free operation.
IMPORTANTREAD ALL INSTRUCTIONS carefully and com-pletely before using the transceiver.
SAVE THIS INSTRUCTION MANUAL This in-struction manual contains important operating instructions forthe IC-M72.
EXPLICIT DEFINITIONS
FEATURESSubmersible constructionBuilt tough to withstand the punishing marine environ-ment, the IC-M72s submersible construction meets IPX8of the corresponding International Standard IEC 60529
(2001) while using BP-245.In addition, the new speaker grill structure with a waterself-draining function is helpful for draining water or sea-water easily.
Dualwatch and tri-watch functionsConvenient functions that allow you to monitor the dis-
tress channel (Ch 16) while receiving one other channel ofyour choice (dualwatch) , or while receiving one other chan-nel of your choice and the call channel (Ch 09) (tri-watch) .See p. 16 for details.
Large, easy-to-read LCDWith the generous dimensions of 22.5(H) 31.5(W) mm;7 8(H) 1
1 4(W) inch, the IC-M72s function display is easy
to read and shows operating conditions at a glance. Back-lighting and contrast can be adjusted to suit your prefer-ences.
Simple operationThe volume knob is on top of the radio, while the channel
buttons are on the front panel. This allows for convenient,one-handed operation.
iii
WORD DEFINITION
R WARNING
CAUTION
NOTE
Personal injury, fire hazard or electric shockmay occur.
If disregarded, inconvenience only. No riskof personal injury, fire or electric shock.
Equipment damage may occur.
-
8/8/2019 Icom IC-M72 Instruction Manual
5/40
iv
PRECAUTIONR WARNING! NEVER connect the transceiver to anAC outlet. This may pose a re hazard or result in an electricshock.
RWARNING! NEVER hold the transceiver so that theantenna is closer than 2.5 cm (1 inch) from exposed parts of
the body, especially the face or eyes, while transmitting. Thetransceiver will perform best if the microphone is 5 to 10 cm (2to 4 inches) away from the lips and the transceiver is vertical.
NEVER connect the transceiver to a power source otherthan the BP-245. Such a connection will ruin the transceiver.AVOID using or placing the transceiver in direct sunlight orin areas with temperatures below 20C (4F) or above+60C (+140F) .
KEEP the transceiver out of the reach of children.
KEEP the transceiver at least 0.9 meters (3.0 ft) away fromyour vessels magnetic navigation compass.
MAKE SURE the exible antenna and battery pack aresecurely attached to the transceiver, and that the antenna andbattery pack are dry before attachment. Exposing the insideof the transceiver to water will result in serious damage to thetransceiver.
BE CAREFUL! The IC-M72 employs submersible con-struction (1.5 m; 4.9 ft depth for 30 min.) . However, once thetransceiver has been dropped, waterproong cannot be guar-anteed due to the fact that the transceiver may be cracked,or the waterproof seal damaged, etc.
For the U.S.A. only CAUTION: Changes or modications to this device, notexpressly approved by Icom Inc., could void your authority tooperate this device under FCC regulations.
Icom, Icom Inc. and the logo are registered trademarks of Icom Incor-porated (Japan) in the United States, the United Kingdom, Germany, France,Spain, Russia and/or other countries.
-
8/8/2019 Icom IC-M72 Instruction Manual
6/40
-
8/8/2019 Icom IC-M72 Instruction Manual
7/40
1
1OPERATING RULESD Priorities Read all rules and regulations pertaining to priorities and
keep an up-to-date copy handy. Safety and distress callstake priority over all others.
You must monitor Channel 16 when you are not operatingon another channel.
False or fraudulent distress calls are prohibited under law.
D Privacy Information overheard but not intended for you cannot law-
fully be used in any way.
Indecent or profane language is prohibited.
D Radio licenses(1) SHIP STATION LICENSEWhen your craft is equipped with a VHF FM transceiver, youmust have a current radio station license before using thetransceiver. It is unlawful to operate a ship station which is notlicensed.
Inquire through your dealer or the appropriate governmentagency for a Ship-Radiotelephone license. This license in-cludes the call sign which is your crafts identication for radiopurposes.
(2) OPERATOR S LICENSEA restricted Radiotelephone Operator Permit is the licensemost often held by small vessel radio operators when a radiois not required for safety purposes.
The Restricted Radiotelephone Operator Permit must beposted near the transceiver or be kept with the operator. Only
a licensed radio operator may operate a transceiver.However, non-licensed individuals may talk over a transceiverif a licensed operator starts, supervises, ends the call andmakes the necessary log entries.
A current copy of the applicable government rules and regu-lations is only required to be on hand for vessels in which aradio telephone is compulsory. However, even if you are notrequired to have these on hand it is your responsibility to bethoroughly acquainted with all pertinent rules and regulations.
NOTE: Even though the IC-M72 is capable of operation
on VHF marine channels 3, 21, 23, 61, 64, 81, 82 and 83,according to FCC regulations these simplex channels can-not be lawfully used by the general public in USA waters.
1
-
8/8/2019 Icom IC-M72 Instruction Manual
8/40
2
SUPPLIED ACCESSORIES AND ATTACHMENTS2I Supplied accessoriesThe following accessories are supplied: Qty.q Handstrap 1w Battery charger 1e Screws for the battery charger (M3.5 30) 2r Belt clip (with screws) 1t AC adapter 1y Li-Ion battery pack 1u Flexible antenna 1
I AttachmentsD Flexible antenna
Connect the supplied flexible an-tenna to the antenna connector.
CAUTION: Transmitting without
an antenna may damage thetransceiver.
NEVER HOLD by the antennawhen carrying the transceiver.
D HandstrapPass the handstrap through the
loop on the top corner of the trans-ceiver as illustrated at left.Facilitates carrying.
q w e
r
t y
u
-
8/8/2019 Icom IC-M72 Instruction Manual
9/40
3
2SUPPLIED ACCESSORIES AND ATTACHMENTS
D Battery pack q Attach the battery pack into the transceiver as below.
w Lock the battery pack with the latch.
CAUTION!:NEVER attach or detach the battery pack when wet.
Be careful when releasing the latch. Because the latch istightly locked, dont use a nger nail to open it you mayinjure yourself. Instead, use something relatively at, likethe edge of a coin or the tip of a screwdriver, to carefullyrelease the latch.
D Belt clipAttach the belt clip to the transceiver as illustrated below.
Supplied screws
2
-
8/8/2019 Icom IC-M72 Instruction Manual
10/40
4
PANEL DESCRIPTION3I Front, top and side panels
q VOLUME CONTROL [VOL]Turns power ON and adjusts the audio level.
w PTT SWITCH [PTT]Push and hold to transmit; release to receive.
e MONITOR KEY [ ] Manually opens the squelch for monitoring the channel
while pushed and held. (p. 10) Push this switch, then adjust the squelch level with
[Y ]/[Z ]. (p. 11) While pushing and holding this switch, turn power ON to
enter the SET mode. (p. 17)
r CHANNEL UP/DOWN KEYS [ Y ]/[Z ] Selects an operating channel. (pgs. 79) Selects the SET mode condition of the item. (p. 17) Selects the SET mode item when pushed with [ ].
(p. 17) Checks TAG channels or changes scanning direction dur-
ing scan. (p. 15)
t CHANNEL 16 KEY [16 9] Selects Channel 16 when pushed. (p. 7) Selects call channel when pushed for 1 sec. (p. 7) Enters call channel write mode when the call channel is
selected and this key is pushed and held for 3 sec. (p. 10)
q
w
e
r
t
Microphone
!0
o
i
u
y
Speaker
Functiondisplay(p. 5)
-
8/8/2019 Icom IC-M72 Instruction Manual
11/40
5
3PANEL DESCRIPTION
y TRANSMIT POWER/LOCK KEY [H/L LOCK] Selects high, middle or low power when pushed. (p. 9) Toggles the lock function ON/OFF when pushed and held
for 1 sec. (p. 10)
u SCAN KEY [SCAN DUAL] Starts and stops normal or priority scan when pushed.
(pgs. 14, 15) Enters watch mode when pushed and held for 1 sec.
(p. 16)
i CHANNEL/WEATHER CHANNEL KEY [CH/WX U/I/C] Selects and toggles the regular channels and weather
channel when pushed. (p. 8) Selects the U.S.A, International, or Canadian* channel
group when pushed and held for 1 sec. (p. 8)- The function display shows which channel group is ac-
tive. *Available with the USA versions only. Push to return to the condition before selecting the chan-
nel when the priority channel or the call channel is se-lected.
o SPEAKER-MICROPHONE CONNECTOR [SP MIC]Connects the optional external speaker-microphone orheadset.
NOTE: Attach the [SP MIC] cap when the optionalspeaker-microphone or headset is not used.
!0 ANTENNA CONNECTORConnects the supplied antenna.
I Function display
q CHANNEL NUMBER READOUT Indicates the selected operating channel number. In SET mode, indicates the selected condition. DUP appears when a duplex channel is selected.
w TAG CHANNEL INDICATOR (p. 15)Appears when TAG channel is selected.
e BATTERY INDICATORIndicates remaining battery power.
Indication
Full Middle Chargingrequired No batteryBattery level
blinks when the battery is overcharged (or over voltage) .
q
we
rt
yu
io
!0!1
!2
!3!4
!5 3
-
8/8/2019 Icom IC-M72 Instruction Manual
12/40
6
3 PANEL DESCRIPTION
r MONITOR INDICATOR (p. 10)Appears when the monitor function is activated.
t DUALWATCH/TRI-WATCH INDICATORS (p. 16)DUAL blinks during dualwatch; TRI blinks during tri-watch.
y VOX INDICATOR (p. 12)Appears when the VOX function is used.
u SCRAMBLER INDICATOR (pgs. 11, 22)Appears when the voice scrambler is activated.*The voice scrambler function is available with some versionsonly.
i CHANNEL NAMING Indicates or scrolls operating channel name or comment.
(p. 13) In SET mode, indicates or scrolls the selected item.
(pgs. 17 22)
o LOCK INDICATOR (p. 10)Appears when the lock function is activated.
!0 CALL CHANNEL INDICATOR (p. 7)Appears when the call channel is selected.
!1 CHANNEL GROUP INDICATOR (p. 8)USA appears when U.S.A.; INT appears when Interna-tional; CAN* appears when Canadian channel group isselected.
*Available with the USA versions only.
!2 WEATHER CHANNEL/WEATHER ALERT INDICATORS(p. 8) WX appears when the weather channel group is
selected. WX ALT appears when the weather alert function is
activated.!3 TRANSMIT POWER INDICATORS (p. 9)
LOW appears when low power is selected. MID appears when middle power is selected. No indication appears when high power is selected.
!4 TRANSMIT INDICATOR (p. 9)Appears during transmit.
!5 BUSY INDICATOR (pgs. 9, 10)Appears when a signal is received or squelch is open.
-
8/8/2019 Icom IC-M72 Instruction Manual
13/40
7
4BASIC OPERATION
34
I Channel selectionIMPORTANT!: Prior to using the transceiver for the firsttime, fully charge the battery pack. This will help maximizethe capability and life of the battery. To avoid damage tothe transceiver, turn the radio OFF while charging.
D Channel 16Channel 16 (Distress channel) is used for establishing initialcontact with another station and for emergency communica-tions. Channel 16 is automatically monitored during bothdualwatch and tri-watch. While standing by, you must monitorChannel 16.
q Push [16 9] to select Channel 16.w Push [CH/WX U/I/C] to return to the condition before se-
lecting Channel 16, or push [Y ]/[Z ] to select the operatingchannel.
D Channel 9 (Call channel)Channel 9 is the leisure-use call channel. Each regularchannel group has separate call channels. In addition, the callchannel is monitored during tri-watch. The call channels canbe re-programmed (p. 10) and may be used to store your most
often used channels in each channel group for quick recall.
q Push and hold [16 9] for 1 sec. to select the call channel. CALL and the call channel number appear. Call channel can be re-programmed. See the Call channel
programming on p. 10 for details.w Push [CH/WX U/I/C] to return to the condition before se-
lecting Channel 9 (call channel) , or push [Y ]/[Z ] to selectthe operating channel.
Push
for 1 sec.Push
-
8/8/2019 Icom IC-M72 Instruction Manual
14/40
D U.S.A., International and Canadian channelsThe IC-M72 has 57 U.S.A., 57 International and 61 Cana-dian* channels. You must select the proper channels for theoperating area. *Available with the USA versions only.
qPush [CH/WX U/I/C] to select the regular channel. If the weather channel appears, push [CH/WX U/I/C] again.
w Push [Y ]/[Z ] to select a channel. DUP appears for duplex channels.
e To change the channel group, push and hold[CH/WX U/I/C] for 1 sec. Repeat until you reach the desired channel group.
D Weather channelsThe IC-M72 has 10 weather channels. They are used formonitoring NOAA (National Oceanographic and Atmospheric Ad-ministration) broadcasts (reception of weather channels possible inU.S.A. only) .
q Push [CH/WX U/I/C] to select the weather channel group.w Push [Y ]/[Z ] to select a weather channel.e Push [CH/WX U/I/C] to return to the condition before se-
lecting the weather channel group.
CONVENIENT!
The IC-M72 can detect a weather alert tone on the
selected weather channel while in another channel(when the
power save function is turned ON) or during scanning. See theSET mode items on p. 18 for details.
Push
Push for 1 sec. Push for 1 sec.
U.S.A. channel*
International channel
ATIS channel
8
4 BASIC OPERATION
-
8/8/2019 Icom IC-M72 Instruction Manual
15/40
9
4BASIC OPERATION
4
I Receiving and transmitting
q Rotate [VOL] clockwise to turn power ON. Opening comment scrolls across the function display. (p. 13) Push [16 9] to skip the opening comment indication.
w Set the volume and squelch level. Push [ ], and push [Z ] to open the squelch. Rotate [VOL] to set the volume level. Push [ ], and push [Y ]/[Z ] to set the squelch level.
e Push [Y ]/[Z ] to select the desired channel.- When receiving a signal, indicator appears while audio is
emitted from the speaker.- Further adjustment of [VOL] may be necessary at this point.
r Push [H/LLOCK] to select the output power, if necessary.- LOW appears when low power is selected; MID appears
when middle power is selected; no indication when high power isselected.
- Choose low or mid. power to conserve battery power, choosehigh power for longer distance communications.
- Some channels are for low power only.t Push and hold [PTT] to transmit, and speak into the mi-
crophone.- The transmit indicator appears while transmitting.- Channel 70 cannot be used for transmission.
y Release [PTT] to receive.
IMPORTANT: To maximize the readability of your trans-mitted signal, pause a second after pushing [PTT] , holdthe microphone 5 to 10 cm (2 to 4 inches) from your mouth,and speak into the microphone using a normal voice level.NOTE: The transceiver has a power save function to con-serve the battery power. The power save function activatesautomatically when no signal is received for 5 sec.To prevent accidental prolonged transmission, etc., the IC-M72 has a time-out timer function. This timer cuts a trans-mission OFF after 5 min. of continuous transmission.
Microphone
Speaker
r Set output power
t Push to transmity Release to receive q Power ON
w Set volume
w Set the squelchlevel
w Set the squelchlevel
e Select thechannel
CAUTION: Transmitting without an antenna maydamage the transceiver.
-
8/8/2019 Icom IC-M72 Instruction Manual
16/40
10
4 BASIC OPERATION
I Call channel programmingThe call channel key is used to select Channel 9 by default,however, you can program your most often-used channel ineach channel group for quick recall.
q Push and hold [CH/WX U/I/C] for 1 sec. several times toselect the desired channel group (USA, INT, CAN) to be pro-grammed.
w Push and hold [16 9] for 1 sec. to se-lect the call channel. CALL and call channel number appear.
ePush and hold [16 9] again for 3 sec.(until a long beep changes to 2 shortbeeps) to enter call channel program-ming condition. Call channel number to be programmed
blinks.
r Push [Y ]/[ Z ] to select the desired
channel.
t Push [16 9] to program the displayedchannel as the call channel.
The call channel number stops blinking.
I Lock functionThis function electronically locks all keys (except for [PTT] , [ ]and [H/LLOCK] ) to prevent accidental channel changes andfunction access. Push [H/LLOCK] for 1 sec. to turn the lock function ON
or OFF.
I Monitor functionThe monitor function releases the noise squelch mute tocheck the volume level. See p. 19 for details of the monitorswitch action. Push and hold [ ] for 1 sec. to activate the monitor func-
tion. and appear and audio is emitted.
Push
for 1 sec.
Appears while themonitor function isin use.
Push
for 1 sec.
Appears while the lockfunction is in use.
-
8/8/2019 Icom IC-M72 Instruction Manual
17/40
11
4BASIC OPERATION
4
I Adjusting the squelch levelTo adjust the IC-M72 s squelch level, use the [Y ] / [Z ] keys asdesired below. In order to receive signals properly, as well asfor the scan to function effectively, the squelch must be ad-
justed to the proper level.
q Push [ ], then adjust the squelch level with [Y ] / [Z ].- SQL and the squelch level are displayed.- There are 11 squelch levels to choose from: OP is completely
open; 10 is tight squelch; 1 is loose squelch level.- When no key is pushed for 5 sec., the transceiver returns to
normal condition.w Push [ ] again to return to normal operating mode.
I Backlighting functionThis function is convenient for nighttime operation. The back-lighting can be turned OFF in the SET mode. (p. 19) Push any key other than [PTT] to turn the backlighting ON.
The backlighting is automatically turned OFF after 5 sec. of
inactivity.
I Voice scrambler operation(available with some versions only)D Activating the scramblerThe voice scrambler provides private communications. Inorder to receive or send scrambled transmissions, you mustactivate the scrambler function rst.
q Select an operating channel other than Channel 16, 70 orweather channels.
w While pushing andholding [ ], push[SCAN DUAL] . SCRM appears.
e To turn the scramblerfunction OFF, repeatstep w . SCRM disappears.
D Programming scramble codes
There are 32 codes (1 to 32) available for programming. Setthe code in the SET mode. In order to understand each other,all transceivers in your group must use the same scramblecode, as well as the same scrambler unit. See p. 22 forScrambler code setting details.
PushShows the squelchlevel.
Appears during squelchlevel adjustment
Appears when the voice scramblerfunction is in use.
-
8/8/2019 Icom IC-M72 Instruction Manual
18/40
12
4 BASIC OPERATION
I VOX function
The VOX function (voice operated transmission) starts transmit-ting when you speak into the headset s microphone. There is
no need to push [PTT] . The IC-M72 automatically returns toreceive mode when you stop talking. Push and hold [ ], then push [H/LLOCK] to turn the
VOX function ON or OFF while connecting the headsetand optional headset adapter to [SP MIC] connector. VOX appears on the LCD while the VOX function turns ON. The VOX gain and VOX delay can be set on the SET mode. (p. 22)
During scan, dual/tri-watch or on a transmission inhibited chan-nel, the VOX function will not be activated.
I AquaQuake water draining functionThe IC-M72 uses a new technology to clear water away fromthe speaker grill: AquaQuake. AquaQuake helps drain wateraway from the speaker housing (water that might otherwise muf-e the sound coming from the speaker) . The IC-M72 emits a vi-brating noise when this function is being used. Push and hold both [16 9] and [H/LLOCK] .
A low beep tone sounds for 9 sec. to drain water, regardless of[VOL] control setting.
The transceiver never accepts a key operation while the AquaQuakefunction is activated. And this function won t be activated when anoptional speaker-microphone or headset is connected.
I Channel namingThe IC-M72 has a capability to assign up to 10-characterchannel names or comments for each operating channel, in-cluding each weather channel. This provides easy recogni-tion of channel usage, or station names, etc.When shipped from the factory, the IC-M72 is programmed
with default names for each VHF marine channel. These de-faults can be changed, if desired.You may replace the factory-set opening comment with acomment of your own. The opening comment appears eachtime the IC-M72 is powered ON. The comment may be up to16 characters long.
D Available characters(=)
(4)
(D)
(N)
(X)
(h)
(r)
( )
(5)
(E)
(O)
(Y)
(i)
(s)
(+)
(6)
(F)
(P)
(Z)
(j)
(t)
(7)
(G)
(Q)
(a)
(k)
(u)
(,)
(8)
(H)
(R)
(b)
(l)
(v)
(/)
(9)
(I)
(S)
(c)
(m)
(w)
(0)
(Space)
(J)
(T)
(d)
(n)
(x)
(1)
(A)
(K)
(U)
(e)
(o)
(y)
(2)
(B)
(L)
(V)
(f)
(p)
(z)
(3)
(C)
(M)
(W)
(g)
(q)
()
NOTE: An optional headset and optional headset adapterare required for the VOX operation.
-
8/8/2019 Icom IC-M72 Instruction Manual
19/40
13
4BASIC OPERATION
4
D Channel name/comment programmingq Push [Y ] / [Z ] to select a channel to
program. Push and hold [CH/WX U/I/C] for 1 sec.
to select a channel group, if necessary.
w While pushing and holding [ ],push [CH/WX U/I/C] . The 1st character of the currently pro-
grammed name or comment blinks.
e Push [Y ] / [Z ] to select a character.
r Push [H/LLOCK] to move to theright; then push [Y ] / [Z ] to select acharacter. Pushing [16 9] , moves to left
t Continue until the desired charactershave been selected, then push
[CH/WX U/I/C] to return to normaloperation.
D Opening comment programmingq While pushing and holding
[SCAN DUAL] , turn power ON. OC is displayed and the 1st character
of the currently programmed comment
blinks.w Push [Y ] / [Z ] to select a character.
e Push [H/L LOCK] to move to theright; then push [Y ] / [Z ] to select acharacter. Pushing [16 9] , moves to left
r Continue until the desired characters
have been selected, then push[CH/WX U/I/C] to return to normaloperation.
The programmed opening comment is brie y displayed orscrolled when the transceiver is powered ON.However, the opening comment indication can be skippedby pushing [16 9] .
5
-
8/8/2019 Icom IC-M72 Instruction Manual
20/40
14
SCAN OPERATION5I Scan typesScanning is an ef cient way to quickly locate signals over awide frequency range. The transceiver has a priority scan set-ting and normal scan setting.
In addition, the Weather alert and Auto scan functions arealso available for scanning. These functions can be activatedsimultaneously, depending on the settings on the SET mode.(pgs. 18, 19)
Set the TAG channels (scanned channel) before scanning.Clear those TAG channels which are not needed or inconve-niently stop scanning, such as digital communications.
Choose priority or normal scan on the SET mode. (p. 18)
PRIORITY SCAN
Priority scan searches through all TAG channels in sequencewhile monitoring Channel 16. When a signal is detected onChannel 16, scan pauses until the signal disappears; when a
signal is detected on a channel other than Channel 16, scanbecomes dualwatch until the signal disappears.
WX*
CH 01
CH 16
CH 02
CH 05 CH 04
CH 03
* Previously selected weather channelwhen weather alert function is ON
NORMAL SCAN
Normal scan, like priority scan, searches through all TAGchannels in sequence. However, unlike priority scan, Chan-nel 16 is not checked unless Channel 16 is set as a TAG
channel.
CH 01 CH 02
WX*
CH 05 CH 04
CH 03
* Previously selected weather channelwhen weather alert function is ON.
-
8/8/2019 Icom IC-M72 Instruction Manual
21/40
15
5SCAN OPERATION
5
I Setting TAG channelsFor more efficient scanning, add desired channels as TAGchannels or clear the TAG for unwanted channels.Untagged will be skipped during scanning. TAG channels canbe assigned to each channel group (USA, INT, CAN) indepen-dently.
q Select the desired channel to set as a TAG channel.w Push and hold both [Y ] and [Z ] for 1 sec. to set the dis-
played channel as a TAG channel. appears in the function display.
e To cancel the TAG channel setting, push and hold both [Y ]and [Z ] for 1 sec. disappears.
Clearing All Tagged Channels in the Selected Channel GroupWhile pushing and holding both [Y ] and [Z ], turn power ONto clear all TAG channels setting in the channel group.
I Starting a scanSet the weather alert function, priority scan function, scan re-sume timer and auto scan function in advance, using the SETmode. (pgs. 18, 19)
q Make sure the desired channel group (e.g., USA, CAN, INT)is selected. Move between channel groups by repeatedlypushing [CH/WX U/I/C] for 1 sec. at a time. When the weather alert function is in use, select the desired
weather channel with [CH/WX U/I/C] and [Y ] / [Z ].w Push [SCAN DUAL] to start priority or normal scan.
SCAN blinks in the function display. 16 appears on the comment indicator during priority scan. When a signal is received, scan pauses until the signal disap-
pears or resumes after pausing 5 sec. according to scan resumetimer setting. (Channel 16 is still monitored during priority scan.) Push [Y ] / [Z ] to check the scanning TAG channels, change the
scanning direction or resume the scan manually.e To stop the scan, push [SCAN DUAL] .
SCAN disappears. Pushing [PTT] , [16 9] or [CH/WX U/I/C] also stops the scan.
[Example]: Starting a normal scan.Scan starts
SCAN indication blinks
Push Push
to stop the scan
When receiving asignal, SCAN indi-cation blinks andaudio is emitted.
6
-
8/8/2019 Icom IC-M72 Instruction Manual
22/40
16
DUALWATCH/TRI-WATCH6I DescriptionDualwatch monitors Channel 16 while you are receivinganother channel; tri-watch monitors Channel 16 and the callchannel while receiving another channel.
I Operationq Select the desired operating channel.w Push [SCAN DUAL] for 1 sec. to start dualwatch or tri-
watch (depending on the SET mode setting; p. 19) . DUAL blinks during dualwatch; TRI blinks during tri-watch. A beep tone sounds when a signal is received on Channel 16. Tri-watch becomes dualwatch when receiving a signal on the call
channel.e To cancel dualwatch/tri-watch, push [SCAN DUAL] again.
DUALWATCH/TRI-WATCH SIMULATION
If a signal is received on Channel 16, dualwatch/tri-watchpauses on Channel 16 until the signal disappears.
If a signal is received on the call channel during tri-watch,tri-watch becomes dualwatch until the signal disappears.
To transmit on the selected channel during dualwatch/tri-watch, push and hold [PTT] .
Dualwatch Tri-watch
Call channel
[Example]: Operating tri-watch on INT channel 07.
Signal is receivedon the call channel.
A signal receive on
Channel 16 alwaystakes priority.
Tri-watch resumes
after the signaldisappears.
Tri-watch starts.
Push for 1 sec.
7
-
8/8/2019 Icom IC-M72 Instruction Manual
23/40
17
67
7SET MODEI SET mode programmingSET mode is used to change the condition of 18 transceiverfunctions: beep tone function, weather alert function, scantype, scan resume timer, auto scan function, dual/tri-watchfunction, monitor key action, backlighting function, LCD con-trast selection, auto power save function, self check function,battery voltage indication, squelch sensitivity, channel namescroll type, scroll speed, scrambler code, VOX gain and VOXdelay.
D SET mode operationq Turn power OFF.w While pushing and holding [ ], turn power ON to enter
the SET mode. BEEP (Beep tone function setting) appears.
e Push [ ], or push [ ]] and [Y ] / [Z ] to select the de-sired item.
r Push [Y ] / [Z ] to select the desired condition of the item.t To exit the SET mode, push [16 9] .
D SET MODE ITEMSBeep tone* Scan type Scan resume timer Auto scan start function Dual/Tri-watch
Monitor keyaction
Displaybacklight
LCDcontrast
VOX delay
VOX gain
Voice scramblercode
Scroll s eed
Power savefunction
Self-check functionBatter volta e indicationS uelch sensitivitChannel name scroll t e
: Push [ ], or while pushing and holding [ ], push [Y ]
: While pushing and holding [ ], push [Z
]*Starting itemAvailability may differ according to versions.Not available with Dutch versions.
-
8/8/2019 Icom IC-M72 Instruction Manual
24/40
18
7 SET MODE
I SET mode itemsD Beep tone function Selects the key touch beep sound ON or US, or turns soundOFF. ON : A xed beep sounds (default) US : The preset beeps (e.g. do, re, mi) sound OFF: Silent operation
DWeather alert function A NOAA broadcast station transmits a weather alert tone be-
fore any important weather announcements. When theweather alert function is turned ON, any detected weatheralert will make the IC-M72 activate a blinking WXALT alertindicator on the function display and repeatedly sound a beeptone. The blinking and beeping stops when the radio is picked
up and operated. The previously selected weather channel ischecked any time during standby, or while scanning, whenthe power save function is activated. ALT appears when the function is set ON.
D Priority scan function The transceiver has 2 scan types normal (OFF) and priority(ON) scans. Normal scan searches all TAG channels in theselected channel group. Priority scan searches all TAG chan-nels in sequence while monitoring Channel 16.
D Scan resume timer The scan resume timer can be set as a pause (OFF) or timerscan (ON). When OFF is selected, the scan pauses until areceived signal disappears. When ON is selected, the scanpauses for 5 sec. after receiving a signal and then resumeseven if the signal has been received.
Push
Scan resume timerOFF (default)
Scan resume timerON
Push
Normal scan Priority scan (default)
Push
Weather alert functionOFF (default)
Weather alert functionON
Push
Beep tone ON Beep tone OFF
-
8/8/2019 Icom IC-M72 Instruction Manual
25/40
19
7SET MODE
7
D Auto scan function The auto scan function starts the desired scan automaticallywhen no signal is received, and no operation is performed for30 sec.
D Dual/Tri-watch function This item selects dual or tri-watch as desired. See p. 16 fordetails.
D Monitor key action The monitor key action cuts off the squelch function tem-porarily. This key action contains PUSH (Pu) or HOLD (Ho)settings as shown below. Pu (PUSH): After pushing [ ] for 1 sec., the squelch opens and
emits audio. The squelch is held open while continu-ously pushing and holding [ ]. (default)
Ho (HOLD): After pushing [ ] for 1 sec., the squelch opens andemits audio even [ ] is released. To close thesquelch, push any key.
D Backlight function This function is convenient for nighttime operation. The back-light can be selected from ON and OFF. The backlight is automatically activated when any key except for
[PTT] is pushed.
The backlight is automatically turned OFF after 5 sec. of inactivity.
Push
Backlight ON(default)
Backlight OFF
Push
Push setting (default) Hold setting
Push
Dualwatch (default) Tri-watch
Push
Auto scan OFF Auto scan ON
-
8/8/2019 Icom IC-M72 Instruction Manual
26/40
20
7 SET MODE
D LCD contrast selection The contrast of the LCD can be selected from Hi (default) andLo.
D Auto power save function The auto power save function reduces current drain by deac-tivating the receiver circuit for preset intervals. ON : The power save function is turned ON. The power save func-
tion will activate when no signal is received, and no operationis performed for 5 sec.
OFF : The power save function is turned OFF.
D Self check function The self check function informs you in case a problem isfound with the radio. Self check automatically and quicklyruns through its diagnostic steps each time the radio is turnedON. Afterwards, the radio switches to normal operation mode. Temperature : Outside of 35 C to +73 C; 31 F to +163 F
(approx.) Connected battery voltage Water intrusion
When any of the bellow error messages appear, see the trou-bleshooting section of this document for advice. (p. 30)
Battery voltage error Temperature error Water intrusion
@ @ @ @ @ @ @@ e ?
@ @ @ @ @ @ @@ e ?
@ @h ?
@ @h ?
@ @h ?
@ @h ?
@ @h ?
@ @h ?
@ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ?e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ?e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @@ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @
@ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ?e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ?e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @@ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
? @ @
? @ @
? @ @
? @ @
? @ @
? @ @
? @ @ @ @ @ @ @ @
? @ @ @ @ @ @ @ @
? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @@ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @@ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ?e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @
? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @@ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @@ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ?e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @ @ @ ? e @ @ @ @ @ @ @ @ e ? @ @ @ @ @ @
@ @ g
@ @ g
@ @ g
@ @ g
@ @ g
@ @ g
@ @ @ @ @ @ @ @
@ @ @ @ @ @ @ @
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
@@
Push
Self check OFF(default)
Self check ON
Push
Power save ON(default)
Power save OFF
Push
High contrast (default) Low contrast
-
8/8/2019 Icom IC-M72 Instruction Manual
27/40
21
7SET MODE
7
D Battery voltage indicator This function controls display or non-display settings of theconnected battery pack s voltage when the power is ON. The voltage of the connected battery pack is displayed for 2 sec.
after power is turned ON.
D Squelch sensitivity function When this function is turned ON (local) , blocking against noiseis improved and the squelch is not easily affected by noise.
D Channel name scroll type Selects the channel name/comment scroll type from 1 and 2. 1: The first 7 characters are displayed for 1 sec. (approx.) then
scrolls. When the channel name/comment is 7 character or less,it does not scroll (default).
2: The channel name/comment scrolls regardless of the number ofcharacters after no name/comment (blank) is indicated for 1 sec.
D Scrolling speed Selects the channel name/comment scroll speed. 1: Scrolls 3.33 characters in a second. 2: Scrolls 2.5 characters in a second. 3: Scrolls 2 characters in a second.
Push
Scroll speed 1 Scroll speed 3
Push
Scroll type 1 (default) Scroll type 2
Push
Squelch sensitivityOFF (default)
Squelch sensitivityON
Push
Voltage indicationOFF (default)
Voltage indication ON
-
8/8/2019 Icom IC-M72 Instruction Manual
28/40
22
7 SET MODE
D Voice scrambler code (available with some versions only)
There are 32 codes (1 to 32) available for programming. Inorder to understand each other, all transceivers in your groupmust share the same scrambler code.
D VOX gain Adjusts the VOX gain level from 1 (low sensitivity) to 6 (high sen-sitivity) when speaking with the optional headset.
D VOX delay Sets the VOX delay timer (0.5 to 3.0 sec. in 0.5 sec. steps) sothat the transceiver keeps on transmitting after you stopsspeaking.
Push
VOX delay 1.0 VOX delay 3.0
Push
VOX gain 1 (default) VOX gain 6
Push
Scramble code 1(default)
Scramble code 32
8BATTERY CHARGING
-
8/8/2019 Icom IC-M72 Instruction Manual
29/40
23
8BATTERY CHARGING
78
IBattery cautions
R DANGER! Use and charge only specified Icom batterypack with Icom transceiver. Only Icom battery pack is testedand approved for use with Icom transceiver. Using third-party or counterfeit battery packs may cause smoke, re, orcause the battery to burst.
D Battery caution R DANGER! DO NOT hammer or otherwise impact the bat-
tery. Do not use the battery if it has been severely impactedor dropped, or if the battery has been subjected to heavypressure. Battery damage may not be visible on the outsideof the case. Even if the surface of the battery does not show
cracks or any other damage, the cells inside the battery mayrupture or catch re. R DANGER! NEVER use or leave battery pack in areas
with temperatures above +60 C (+140 F). High temperaturebuildup in the battery, such as could occur near fires orstoves, inside a sun-heated car, or by setting the battery indirect sunlight may cause the battery to rupture or catch re.Excessive temperatures may also degrade battery perfor-mance or shorten battery life.
R DANGER! DO NOT expose the battery to rain, snow,seawater, or any other liquids. Do not charge or use a wetbattery. If the battery gets wet, be sure to wipe it dry beforeusing. The battery by itself is not waterproof.
R DANGER! NEVER incinerate a used battery pack since
internal battery gas may cause a rupture or explosion. R DANGER! NEVER solder the battery terminals, or
NEVER modify the battery pack. This may cause heat gen-eration, and the battery may rupture, emit smoke or catchre.
R DANGER! Use the battery only with the transceiver for
which it is specified. Never use a battery with any otherequipment, or for any purpose that is not speci ed in this in-struction manual.
R DANGER! If fluid from inside the battery gets in youreyes, blindness can result. Rinse your eyes with cleanwater, without rubbing them, and see a doctor immediately.
WARNING! Immediately stop using the battery if it emits anabnormal odor, heats up, or is discolored or deformed. If anyof these conditions occur, contact your Icom dealer or dis-tributor.
WARNING! Immediately wash, using clean water, any partof the body that comes into contact with uid from inside thebattery.
Misuse of Lithium-ion batteries may result in the follow-ing hazards: smoke, re, or battery rupture.Misuse can also cause other battery damage or degra-dation of battery performance.
8
-
8/8/2019 Icom IC-M72 Instruction Manual
30/40
24
8 BATTERY CHARGING
WARNING! NEVER put the battery in a microwave oven,high-pressure container, or in an induction heating cooker.This could cause overheating, a re, or cause the battery torupture.
CAUTION! Always use the battery within the speci ed tem-
perature range for the transceiver ( 20 C to +60 C; 4F to+140 F) and the battery itself ( 20 C to +60 C; 4F to+140 F). Using the battery out of its speci ed temperaturerange will reduce the battery s performance and battery life.Please note that the speci ed temperature range of the bat-tery may exceed that of the transceiver. In such cases, thetransceiver may not work properly because it is out of its op-erating temperature range.
CAUTION! Shorter battery life could occur if the battery isleft fully charged, completely discharged, or in an excessivetemperature environment (above +45 C; +113 F) for an ex-tended period of time. If the battery must be left unused for along time, it must be detached from the radio after discharg-
ing. You may use the battery until the battery indicatorshows half-capacity, then keep it safely in a cool dry placewith the temperature between 20 C to +25 C ( 4F to+77 F).
D Charging caution R DANGER! NEVER charge the battery pack in areas with
extremely high temperatures, such as near res or stoves,inside a sun-heated car, or in direct sunlight. In such envi-ronments, the safety/protection circuit in the battery will acti-
vate, causing the battery to stop charging. WARNING! DO NOT charge or leave the battery in the bat-
tery charger beyond the specified time for charging. If thebattery is not completely charged by the speci ed time, stopcharging and remove the battery from the battery charger.Continuing to charge the battery beyond the speci ed timelimit may cause a re, overheating, or the battery may rup-ture.
WARNING! NEVER insert the battery and transceiver (bat-tery attached to the transceiver) into the charger if it is wet orsoiled. This could corrode the battery charger terminals ordamage the charger. The charger is not waterproof.
CAUTION! DO NOT charge the battery outside of the spec-
ied temperature range: 0 C to +45 C (+32 F to +113 F).Icom recommends charging the battery at +20 C (+68 F).The battery may heat up or rupture if charged out of thespecified temperature range. Additionally, battery perfor-mance or battery life may be reduced.
8
-
8/8/2019 Icom IC-M72 Instruction Manual
31/40
25
8BATTERY CHARGING
8
ISupplied battery chargerD BC-166 installation D Charging
q Connect the AC adapter as shown below.w Insert the battery pack with/without the transceiver into the
charger. The charge indicator lights orange.
e Charge the battery pack approx. 11 hours, depending onthe remaining power condition. The charge indicator lights green when charging is complete.
NOTE: The battery charger, BC-166, has charging timer.The timer stops the charging process after 14 hours (ap-prox.) .
Transceiver
Batterypack
ACadapter
Turn the transceiv-er power OFF dur-ing charging.
Charger indicator
q
w
e
Supplied screws
Supplied screws To a desktop
For added stability
To a wall
Eyelet:
Use a rubber band tosecure the transceiv-er, if desired.
8 BATTERY CHARGING
-
8/8/2019 Icom IC-M72 Instruction Manual
32/40
26
8 BATTERY CHARGING
IOptional battery chargersD AD-114 installation
q Connect both the 3-pin and 10-pin connectors of thecharger to the AD-114 desktop charger adapter s plug.
w Install the adapter into the charger in the direction of thearrow, then use the supplied 2 screws to secure thecharger adapter to the charger.
D Rapid charging with the BC-119N+AD-114The optional BC-119N provides rapid charging of batterypacks. The following options are additionally required. AD-114 charger adapter An AC adapter (BC-145) or the DC power cable (OPC-
515L/CP-17L) .
AD-114 chargeradapter is instal-led in BC-119N.
AC adapter(Not suppliedwith someversions.)
Optional OPC-515L (for 13.8 Vpower source) or CP-17L (for 12V cigarette lighter socket) can beused instead of the AC adapter.
Transceiver
Battery pack
Turn power OFF
Desktop charger adapter
10-pin connector
3-pin connector
Suppliedscrews
8BATTERY CHARGING
-
8/8/2019 Icom IC-M72 Instruction Manual
33/40
27
8BATTERY CHARGING
8
D Rapid charging with the BC-121N+AD-114The optional BC-121N allows up to 6 battery packs to becharged simultaneously. The following options are addition-ally required. Six AD-114 charger adapters
An AC adapter (BC-157) or the DC power cable (OPC-656)Transceiver
Battery pack AC adapter(Purchaseseparately) AD-114 charger adapters
are installed in each slot.
DC power cable (OPC-656)(Connect with the DC power supply;13.8 V/at least 7 A)
Turn power OFF
OPTIONAL SWIVEL BELT CLIP9
-
8/8/2019 Icom IC-M72 Instruction Manual
34/40
28
OPTIONAL SWIVEL BELT CLIP9I
Attachmentq Screw the base clip to theback of the transceiverusing the two screws (sup-plied) , as shown at right.
w Clip the belt clip over your belt and insert the transceiver.
e Once the transceiver is locked in place, it swivels.
IDetachment Turn the transceiver upside down in the direction of the
arrow and pull out from the belt clip.
R CAUTION!: HOLD THE TRANSCEIVER TIGHTLYWHEN HANGING OR DETACHING THE TRANSCEIVERFROM THE BELT CLIP.Otherwise the transceiver may not be attached to the belt
clip or swivelled properly if the transceiver is accidentallydropped and the base clip is scratched or damaged.
Supplied screws
10OPTIONAL SPEAKER-MICROPHONE
-
8/8/2019 Icom IC-M72 Instruction Manual
35/40
29
10OPTIONAL SPEAKER-MICROPHONE
9
10
IHM-125 descriptions
NEVER immerse the connector in water. If the connector be-
comes wet, be sure to dry it BEFORE attaching it to the trans-ceiver.
NOTE: The microphone is located at the top of thespeaker-microphone, as shown in the diagram above. Tomaximize the readability of your transmitted signal (voice) ,hold the microphone approx. 2.5 cm (1 inch) from yourmouth, and speak in a normal voice level.
IAttachmentInsert the speaker-mic connector onto the [SP MIC ] connec-
tor and carefully screw it tight, as shown in the diagrambelow. Be careful not to cross-thread the connection.
IMPORTANT: KEEP the transceiver s [SP MIC] connectorcap attached when the speaker-microphone is not in use.Water will not get into the transceiver even if the cover isnot attached; however, the terminals (pins) will become
rusty, or the transceiver will function abnormally if the con-nector has become wet.
Alligator type clipTo attach the speaker-mic.to your shirt or collar, etc.
PTT switchTransmits during push.Receives during release.
Microphone
Speaker
Turn the transceiver power OFFwhen connecting the HM-125.
Set the triangle mark
to the front side.
CAUTION: Attach the speaker-
microphone s connector securelyto prevent accidental dropping, orwater intrusion in the connector.
Detaching:Pull up the capin the directionof the arrow todetach it.
Attaching:Attach the capin the directionof the arrowcompletely.
TROUBLESHOOTING11
-
8/8/2019 Icom IC-M72 Instruction Manual
36/40
PROBLEM
The transceiver does notturn ON.
No sound from thespeaker.
Transmitting is impossible,or high power can not beselected.
The displayed channelcannot be changed.
Scan does not start.
No beeps.
Self check error.
(Temperature)
Self check error.(Battery voltage)
Transmitting continuouslywhile not speaking whenusing VOX function.
CHARGE commentblinks
30
TROUBLESHOOTING11POSSIBLE CAUSE
The battery is depleted.
Bad connection to the battery pack.
Squelch level is too tight. Volume level is too low. Speaker has been exposed to water.
Water has entered to [SP MIC] connector.
Some channels are for low power or receiveonly.
The battery is exhausted.
The battery is overcharged. The output power is set to low.
Lock function is activated.
TAG channels are not programmed.
Beep tones are turned OFF.
The temperature is outside of 35 C to +73 C;
31 F to +163 F (approx.).
The connected battery pack s voltage is morethan 11 V.
Ambient noise is too loud.
The connected battery is depleted.
SOLUTION
Recharge the battery pack.
Check the connection to the transceiver.
Set squelch to the threshold point. Rotate [VOL] to set a suitable level. Push and hold both [16 9] and [H/LLOCK] to
drain water from the speaker. Dry [SP MIC] connector.
Change channels.
Recharge the battery pack.
Verify the battery voltage is correct. Push [H/LLOCK] to select high power.
Push [H/LLOCK] for 1 sec. to cancel the function.
Set the desired channels as TAG channels.
Set the beep tones to ON (Fix Beep/User Beep) inthe SET mode.
Leave the transceiver at room temperature for a
while. Turn the power ON to check if the internaltemperature has returned to normal.
Verify the battery voltage is correct.
Push [ ] and [H/LLOCK] to deactivate theVOX function.
Set the VOX gain to lower sensitive value.
Recharge the battery pack.
REF.
pgs.25 27
p. 3
p. 11p. 9
p. 12
pgs. 8, 9,31
pgs.25 27
p. 9
p. 10
p. 15
p. 18
p. 12
p. 22
pgs.25 27
12VHF MARINE CHANNEL LIST
-
8/8/2019 Icom IC-M72 Instruction Manual
37/40
31
12VHF MARINE CHANNEL LIST
1112
Channel number
USA CAN Transmit Receive
Frequency (MHz)
INT
Channel number Frequency (MHz)
USA CAN Transmit ReceiveINT
Channel number Frequency (MHz)
USA CAN Transmit ReceiveINT
Channel number Frequency (MHz)
USA CAN Transmit ReceiveINT
WX channelFrequency (MHz)
Transmit Receive
01 156.050 160.650
01A 156.050 156.050
02 156.100 160.700
03 156.150 160.750
03A 156.150 156.150
156.200 160.80004A 156.200 156.200
156.250 160.850
05A 05A 156.250 156.250
06 06 156.300 156.300
156.350 160.950
07A 07A 156.350 156.350
08 08 156.400 156.400
09 09 156.450 156.450
10 10 156.500 156.500
11 11 156.550 156.550
12 12 156.600 156.600
13 * 13 * 156.650 156.650
14 14 156.700 156.70015 * 15 * 156.750 156.750
16 16 156.800 156.800
17 * 17 * 156.850 156.850
156.900 161.500
18A 18A 156.900 156.900
01
02
03
04
05
06
07
08
09
10
11
12
13
1415 *
16
17
18
156.950 161.550
19A 19A 156.950 156.950
20 20 * 157.000 161.600
21 157.050 161.650
21A 21A 157.050 157.050
157.100 161.70022A 22A 157.100 157.100
23 157.150 161.750
23A 157.150 157.150
24 24 157.200 161.800
25 25 157.250 161.850
26 26 157.300 161.900
27 27 157.350 161.950
28 28 157.400 162.000
60 156.025 160.625
156.075 160.675
61A 61A 156.075 156.075
156.125 160.725
62A 156.125 156.125156.175 160.775
63A 156.175 156.175
64 156.225 160.825
64A 64A 156.225 156.225
19
20
21
22
23
24
25
26
27
28
60
61
62
63
64
20A 157.000 157.000
66A 66A *156.325 160.925
67 * 67 156.375 156.375
68 68 156.425 156.425
69 69 156.475 156.475
70 70 156.52571 71 156.575 156.575
72 72 156.625 156.625
73 73 156.675 156.675
74 74 156.725 156.725
77 * 77 * 156.875 156.875
156.925 161.525
78A 78A 156.925 156.925
156.975 161.575
79A 79A 156.975 156.975
157.025 161.625
80A 80A 157.025 157.025
157.075 161.675
81A 81A 157.075 157.075157.125 161.725
82A 82A 157.125 157.125
66
67
68
69
7071
72
73
74
77
78
79
80
81
82
156.325 156.32566A
85 85 157.275 161.875
85A 157.275 157.275
86 86 157.325 161.925
86A 157.325 157.325
87 87 157.375 161.975
87A 157.375 157.37588 88 157.425 162.025
88A 157.425 157.425
85
86
87
88
21b Rx only
Rx only
161.650
25b Rx only 161.850
28b Rx only 162.000
83b Rx only 161.775
4
1 RX only 162.550
2 RX only 162.400
3 RX only 162.475
5 RX only 162.450
6 RX only 162.500
7 RX only 162.525
8 RX only 161.650
9 RX only 161.775
10 RX only 163.275
RX only 162.425
156.275 160.875
65A 65A 156.275 156.275
65
65A 84A
83 157.175 161.775
83A 83A 157.175 157.175
84 84 157.225 161.825
83
84
157.225 157.225
*Low power only. NOTE: Simplex channels 3, 21, 23, 61, 64, 81, 82 and 83 CANNOT be lawfully used by the general public in USA waters.The programmed channels are differ according to versions.
SPECIFICATIONS13
-
8/8/2019 Icom IC-M72 Instruction Manual
38/40
32
SPECIFICATIONS13D GENERAL Frequency coverage : TX 156.025 157.425 MHz
RX 156.050 163.275 MHz Mode : 16K0G3E Power supply requirement : Speci ed Icom s battery pack only Current drain (at 7.5 V DC; approx.) :
TX High (at 6 W) 1.7 ATX Mid. (at 3 W) 1.3 A
TX Low (at 1 W) 0.7 ARX Max. audio 400 mA (internal speaker)
200 mA (external speaker) Useable temperature range : 20 C to +60 C; 4F to +140 F Frequency error : 10 ppm Antenna connector : SMA (50 nominal) Dimensions : 52.5(W) 125(H) 30(D) mm
(Projections not included) 21 16(W) 429 32(H) 13 16(D) inch Weight (with BP-245) : Approx. 280 g (9.9 oz)
D TRANSMITTER Output power (at 7.5 V DC) : 6 W* (High) , 3 W (Middle)
and 1 W (Low) *5 W for some versions Modulation system : Variable reactance frequency mod-
ulation Max. frequency deviation : 5 kHz Adjacent channel power : 70 dB Spurious emissions : 68 dBc typical
D RECEIVER Receive system : Double-conversion superhetero-
dyne Sensitivity (12 dB SINAD) : 0.22 V typical Squelch sensitivity : 0.35 V typical (at threshold) Intermodulation rejection ratio: 70 dB typical Spurious response rejection ratio:
70 dB typical
Adjacent channel selectivity : 70 dB typical Audio output power :
Internal speaker 0.6 W typical at 10% distortion with an8 load
External speaker 0.35 W typical at 10% distortion with an8 load
All stated speci cations are subject to change without notice orobligation.
14OPTIONS
-
8/8/2019 Icom IC-M72 Instruction Manual
39/40
33
1314
14D BATTERY CASE AND PACK BP-245 Li-Ion BATTERY PACK
7.4 V/2000 mAh Li-Ion battery pack.
D CHARGERS BC-119N DESKTOP CHARGER + AD-114 CHARGER ADAPTER
+ BC-145 AC ADAPTER
For rapid charging of battery packs. An AC adapter is supplied withthe charger depending on versions. Charging time: approx. 3 to 4hours
BC-121N MULTI -CHARGER + AD-114 CHARGER ADAPTER (6 pcs.)+ BC-157 AC ADAPTERFor rapid charging of up to 6 battery packs (six AD-114 s are re-quired) simultaneously. An AC adapter should be purchased sepa-rately. Charging time: approx. 3 to 4 hours.
BC-166 DESKTOP CHARGER + BC-147A/E/BM-95V AC ADAPTERUsed for regular charging of battery pack. The same as suppliedwith the transceiver. Charging time: approx. 11 to 12 hours
D BELT CLIPS MB-103 BELT CLIP
The same as supplied with the transceiver. MB-86 SWIVEL BELT CLIP
Belt clip for swivel type.
D DC CABLES CP-17L CIGARETTE LIGHTER CABLE
Charges the battery pack through a 12 V cigarette lighter socket.(For BC-119N)
OPC-515L/OPC-656 DC POWER CABLESCharges the battery pack using 13.8 V power source instead of theAC adapter.OPC-515L: For BC-119N
OPC-656 : For BC-121N
D OTHER OPTIONS HM-125 SPEAKER -MICROPHONE
Full sized waterproof (IPX7; 1m/30 min.) speaker-microphone. In-cludes an alligator clip to attach the speaker mic to your shirt, collar,etc.
HS-94/HS-95/HS-97 HEADSET + OPC-1392 HEADSET ADAPTERHS-94: Ear-piece typeHS-95: Neck-arm typeHS-97: Throat microphone
*These headsets and headset adapter are non-waterproof. FA-S64V FLEXIBLE ANTENNA
Same as that supplied with the transceiver.
Available or applicable options may differ according tocountries. Ask your authorized dealer for details.
-
8/8/2019 Icom IC-M72 Instruction Manual
40/40
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-6479D-1EX- qPrinted in Japan
2005 2006 Icom Inc.