id. ys - rajasthan · asthan rajya vioyut prasaran nigam lto. corporate identity number...

ASTHAN RAJY A VIOYUT PRASARAN NIGAM LTO.Corporate Identity Number (CIN) : U40109RJ20005GC016485

Regd. Office: Vidyut Bhawan, Jyoti Nagar, Jaipur -302 005(AN 150 9001:2008 Certified Company)

OFFICE OF THE SUPERINTENDING ENGINEER (Contracts-II)MM Building of RVPN, Old Power House Premises ,Near Ram Mandir, Banipark, Jaipur-302006Tele.:- 0141 2208919,Cell 9413382626,Fax No.:- 01412208924 Email- [email protected]

No. RVPN/SE(Contracts-1l )/XEN-4/F. ID. Y s: JAIPUR

The Zonal Chief Engineer (T&C),RVPN, Jaipur I Ajmer I Jodhpur.

Sub:- BSR for Construction works of Sub-stations and Maintenance works ofSub-stations & Lines on Labour contract basis (Effective from 1-04-2017).

The CMD level Purchase Committee has approved the revised BSR as on1.04.2017 for carrying out Construction works of Sub-stations and Maintenance worksof Sub-stations & Lines on labour contract basis. The revised BSR as on 1.04.2017 maykindly be circulated to all the field officers under your control for further needful.

Encls: - As above.

(~~a)Superintending Engineer

(Contracts-II)

to the followings for information an~essary actionCopy submitted I forwardedplease.

1. The Addl. Chief Engineer (Contracts), RVPN, Jaipur2. The Superintending Engineer ( ), RVPN, _3. The Executive Engineer ( ), RVPN, _

RAJASTHAN RAJYA VIDHUT PRASARAN NIGAM LTO

SCHEDULE OF RATES FOR ERECTION OF UNIT QUANTITY ITEMS OF SUB STATION ON LABOUR CONTRACT BASIS

1) The retes for the erectionworks given in this BSR are inclusive of all types of labour charges,but exclusive of service tax,sales tax &insurance charges etc.2) The base date for rates given in this schedule is 1 042017CODE DESCRIPTION UNIT Rate (Rs); updatedNO. 1.4.2015 Rates (Rs)

20171 EARTH MESHWORK

A-1 Laying of earth mesh with 25mm 12Smmdia. M.S. Rod at a depth of O.SOmetre from toplevel of foundations, including excavation of trench of required depth and backfilling of thesame, transportation of M. S. Rods from site store to locations, welding of M. S. Rod to M. S.Rod along the length, at crossings andwith earth electrodes as per drawing, application ofbitumen compound and covering with bitumen impregnated tape on all welded joints, for thetype of soil prevalent at O.SOmetre below top level of foundations (M. S. Rod of above sizes &M. S. Flat as required shall be made available by RVPN).a) In case electricitv is made available by RVPNwithout charges.i) Normal drv soil Metres 23.00 24.00ii) Hard soil 1Murram 1Black cotton soil Metres 24.00 26.00iii) Soft rock Metres 33.00 35.00iv) Hard rock (with blasting) Metres 51.00 54.00v) Hard rock (blasting prohibited) Metres 56.00 60.00b) In case diesel generator is arranged by the Contractor at his own cost.i)Normal drv soil Metres 31.00 33.00ii) Hard soil 1Murram 1Black cotton soil Metres 33.00 35.00iii) Soft rock Metres 43.00 46.00iv) Hard rock (with blasting) Metres 61.00 65.00v) Hard rock (blasting prohibited) Metres 6S.00 72.00

A-2 Laying of earth mesh with 40 mm. dia. M.S. Rod at a depth of O.SOmetre from top level offoundations, including excavation of trench of required depth and backfilling of the same,transportation of M. S. Rods from site store to locations, welding of M. S. Rod to M. S. Rodalong the length, at crossings and with earth electrodes as per drawing, application ofbitumen compound and covering with bitumen impregnated tape on all welded joints, for thetype of soil prevalent at O.SOmetre below top level of foundations (M. S. Rod of above sizes &M. S. Flat as required shall be made available by RVPN).a) In case electricitv is made available by RVPNwithout charges.i) Normal drv soil Metres 45.00 48.00ii) Hard soil 1Murram 1Black cotton soil Metres 45.00 48.00iii) Soft rock Metres 66.00 70.00.iv) Hard rock (with blasting) Metres SO.OO 85.00v) Hard rock (blasting prohibited) Metres 9S.00 104.00b) In case diesel generator is arranged by the Contractor at his own cost.i) Normal drv soil Metres 59.00 63.00ii) Hard soil 1Murram 1Black cotton soil Metres 59.00 63.00iii) Soft rock Metres 79.00 84.00iv) Hard rock (with blasting) Metres 95.00 101.00v) Hard rock (blasting prohibited) Metres 110.00 117.00

B-1 Laying of earthing risers of 50x6mm 150x10mm 150x12mm size M. S. Flat at a depth of O.SOmetre from top level of foundations, including excavation of trench of required depth andbackfilling of the same, transportation of M. S. Flat from site store to locations, preparationofrisers, bending as per requirement (after heating if necessary),fixing on and welding 1boltingto equipment 1structure and peaks of structures, laying in the trench,welding to the earthmesh of M. S. Rod as per drawing, includingwelding of extra length of M. S. Flat if required,application of bitumen compound and coveringwith bitumen impregnated tape on all weldedjoints, painting of all surfaces of risers above ground level with red oxide and green paint, forthe type of soil prevalent at O.SOmetre below top level of foundations (M. S. Rod of abovesizes & M. S. Flat as required shall be made available by RVPN).a) In case electricity is made available by RVPNwithout charges.i) Normal drv soil Metres 25.00 27.00ii) Hard soil 1Murram 1Black cotton soil Metres 26.00 28.00iii) Soft rock Metres 36.00 38.00ill)_Hard rock (with blasting) Metres 55.00 59.00v) Hard rock (blasting prohibited) Metres 61.00 65.00b) In case diesel generator is arranged by the Contractor at his own cost.i) Normal drv soil Metres 36.00 38.00U1Hardsoil 1Murram 1Black cotton soil Metres 3S.00 40.00iii) Soft rock Metres 4S.00 51.00iv) Hard rock (with blasting) Metres 66.00 70.00v) Hard rock (blasting prohibited) Metres 73.00 78.00

XEN-4(Contracts)

Page 1018

RAJASTHAN RAJYAVIDHUT PRASARAN NIGAM LTD

SCHEDULE OF RATES FOR ERECTION OF UNIT QUANTITY ITEMS OF SUB STATION ON LABOUR CONTRACT BASIS

1) The retes for the erection works given in this BSR are inclusive of all types of labour charges.but exclusive of service tax.sales tax &insurance charges etc.2) The base date for rates given in this schedule is 1 042017CODE DESCRIPTION UNIT Rate (Rs); updatedNO. 1.4.2015 Rates (Rs)

2017B-2 Laying of earthing risers of 75 x 12mm size M. S. Flat at a depth of 0.80 metre from top level

of foundations. including excavation of trench of required depth and backfilling of the same.transportation of M. S. Flat from site store to locations. preparationof risers. bending as perrequirement (after heating if necessary). fixing on and welding! bolting to equipment!structure and peaks of structures. laying in the trench. welding to the earth mesh of M. S. Rodas per drawing. includingwelding of extra length of M. S. Flat if required. application ofbitumen compound and covering with bitumen impregnated tape on all welded joints. paintingof all surfaces of risers above ground level with red oxide and green paint. for the type of soilprevalent at 0.80 metre below top level of foundations (M. S. Rod of above sizes & M. S. Flatas required shall be made available by RVPN).a) In case electricitv is made available bv RVPNwithout charqes,i) Normal dry soil Metres 48.00 51.00ii) Hard soil! Murram ! Black cotton soil Metres 48.00 51.00iiil Soft rock Metres 69.00 73.00iv) Hard rock (with blastiQ9l Metres 84.00 89.00v) Hard rock (blastinQprohibited) Metres 100.00 106.00b) In case diesel aeneretor is arranaed bv the Contractor at his own cost.il Normal drv soil Metres 63.00 67.00ii) Hard soil! Murram ! Black cotton soil Metres 63.00 67.00iii) Soft rock Metres 83.00 88.00i-a Hard rock (with blasting) Metres 98.00 104.00v) Hard rock (blastir1gJ)rohibited) Metres 113.00 120.00

C-1 Placing! Driving of earth electrode of 25 !28mm dia. M. S. Rod of length 3.30 meters(approx.) to a depth of 3.80 meters from the top level of foundations. including excavation ofpit as required and back filling of the same. transportation of M. S. Rod from site store tolocations. cutting of M. S. Rod to desired length. preparationof one end as spike if necessary.welding of earth electrode to earth mesh of M. S. Rod as per drawing. application of bitumencompound and covering with bitumen impregnated tape on all welded joints. for the type ofsoil prevalent at 3.80 metres below top level of foundations (M. S. Rod of above sizes & M. S.Flat as required shall be made available by RVPN).a) In case electricitv is made available bv RVPNwithout charaes.i) Normal dry soil Nos. 188.00 200.00iil Hard soil! Murram ! Black cotton soil Nos. 313.00 333.00iii) Soft rock Nos. 500.00 532.00iv) Hard rock (with blastinq) Nos. 875.00 932.00v) Hard rock (blasting prohibited) Nos. 993.00 1057.00b) In case diesel aenerator is arranged bv the Contractor at his own cost.i) Normal dry soil Nos. 266.00 283.00ii) Hard soil! Murram ! Black cotton soil Nos. 391.00 416.00iii) Soft rock Nos. 579.00 616.00iv_l_Hard rock (with blasting) Nos. 954.00 1016.00v) Hard rock (blastina._m-ohibited) Nos. 1070.00 1139.00

C.2 Placing! Driving of earth electrode of 40 mm dia. M. S. Rod of length 3.30 meters (approx.) toa depth of 3.80 meters from the top level of foundations. including excavation of pit asrequired and back filling of the same. transportation of M. S. Rod from site store to locations.cutting of M. S. Rod to desired length. preparationof one end as spike if necessary.weldingof earth electrode to earth mesh of M. S. Rod as per drawing. application of bitumencompound and covering with bitumen impregnated tape on all welded joints. for the type ofsoil prevalent at 3.80 metres below top level of foundations (M. S. Rod of above sizes & M. S.Flat as required shall be made available by RVPN).a) In case electricitv is made available by RVPNwithout charaes,i) Normal dry soil Nos. 308.00 328.00iil Hard soil! Murram ! Black cotton soil Nos. 474.00 505.00iii) Soft rock Nos. 876.00 933.00i-a Hard rock (with blasting) Nos. 1170.00 1246.00v) Hard rock (blastinQ_Qrohibited) Nos. 1496.00 1593.00I(b) In case diesel cenerator is arranged bv the Contractor at his own cost.i) Normal dry soil Nos. 413.00 440.00ii) Hard soil! Murram ! Black cotton soil Nos. 578.00 615.00iii}_Softrock Nos. 979.00 1042.00iv) Hard rock (with blasting) Nos. 1274.00 1356.00v) Hard rock (blastinQprohibitedl Nos. 1600.00 1704.00

XEN-4(Contracts)

Page 2 018

RAJASTHAN RAJYA VIOHUT PRASARAN NIGAM LTO

SCHEDULE OF RATES FOR ERECTION OF UNIT QUANTITY ITEMSOF SUB STATION ON LABOUR CONTRACT BASIS

1) The retes for the erection works given in this BSR are inclusive of all types of labour charges,but exclusive of service tax,sales tax &insurance charges etc.2) The base date for rates given in this schedule is 1 042017CODE DESCRIPTION UNIT Rate (Rs); updatedNO. 1.4.2015 Rates (Rs)

2017D.1 Placing of earth electrode of 25 I 28mm dia. M. S. Rod of length 7.50 meters (approx.) to a

depth of 8.00 meters from the top level of foundations, including drilling of 200 mm dia. earthpit having a throughout bore of 200 mm dia to a depth of 8.00 metres from the top level of thefoundations, in all types of rocks by DTH system and overburden, including back filling of pitwith Bentonite slurry (with cost of Bentonite slurry), including its preparation, transportation ofM. S. Rod and Bentonite from site store to location, cutting of M. S. Rod to desired length,welding of earth electrode to earth mesh of M. S. Rod as per drawing, application of bitumencompound and covering with bitumen impregnated tape on all welded joints (M. S. Rod ofabove sizes & M. S. Flat as required shall be made available by RVPN).'j) In case electricity is made available by RVPNwithout charoes. Nos. 10548.00 11230.00iilln case diesel aenerator is arral'lQ_edbv the Contractor at his own cost. Nos. 10625.00 11312.00

D.2 Placing of earth electrode of 40 mm dia. M. S. Rod of length 7.50 meters (approx.) to adepth of 8.00 meters from the top level of foundations, including drilling of 200 mm dia. earthpit having a throughout bore of 200 mm dia to a depth of 8.00 metres from the top level of thefoundations, in all types of rocks by DTH system and overburden, including back filling of pitwith Bentonite slurry (with cost of Bentonite slurry), including its preparation, transportation ofM. S. Rod and Bentonite from site store to location, cutting of M. S. Rod to desired length,welding of earth electrode to earth mesh of M. S. Rod as per drawing, application of bitumencompound and covering with bitumen impregnated tape on all welded joints (M. S. Rod ofabove sizes & M. S. Flat as required shall be made available by RVPN).

illn case electricity is made available by RVPNwithout charoes. Nos. 10548.00 11230.00iilln case diesel aenerator is arrang_edbv the Contractor at his own cost. Nos. 10625.00 11312.00

E.1 Placing of earth electrode of 25 I 28mm dia. M. S. Rod of length 7.50 meters (approx.) to adepth of 8.00 meters from the top level of foundations in already bored hole, including backfilling of pit with Bentonite slurry (with cost of Bentonite slurry), including its preparation,transportation of M. S. Rod and Bentonite from site store to location, cutting of M. S. Rod todesired length, welding of earth electrode to earth mesh of M. S. Rod as per drawing,application of bitumen compound and covering with bitumen impregnated tape on all weldedjoints (M. S. Rod of above sizes & M. S. Flat as required shall be made available by RVPN).illn case electricity is made available by RVPNwithout charaes. Nos. 1243.00 1323.00iilln case diesel aenerator is arrang_edbv the Contractor at his own cost. Nos. 1320.00 1405.00

E.2 Placing of earth electrode of 40 mm dia. M. S. Rod of length 7.50 meters (approx.) to adepth of 8.00 meters from the top level of foundations in already bored hole, including backfilling of pit with Bentonite slurry (with cost of Bentonite slurry), including its preparation,transportation of M. S. Rod and Bentonite from site store to location, cutting of M. S. Rod todesired length, welding of earth electrode to earth mesh of M. S. Rod as per drawing,application of bitumen compound and covering with bitumen impregnated tape on all weldedjoints (M. S. Rod of above sizes & M. S. Flat as required shall be made available by RVPN).

illn case electricity is made available by RVPNwithout charaes. Nos. 1328.00 1414.00iilln case diesel aenerator is arranaed bv the Contractor at his own cost. Nos. 1434.00 1527.00

2 ERECTION OF SUB-STATION STEEL STRUCTURES columns, beams, lighting mast and M.T. 2180.00 2321.00equipment structures (excluding Circuit Breakers and Capacitor Banks) of all types includingtransportation of structure members, nuts & bolts, washers, etc. from site store to locations,their assembly, placing on foundation, fixing of template, with foundation bolts as required,levelling and preparing for grouting as required, but excluding grouting, erection after groutingand tightening & punchingof nuts & bolts. (Maximum height of structures up to 20 meters)

3 BUS-BAR WORKA. STRINGING of 220 KV,132 KV, 33 KV & 11KV Bus Bar of ACSR & Tarantulla conductor,

including transportation of conductor, disc insulators and tension hardware from site stores tolocation, laying and cutting required length of conductor, cleaning and assembly of discinsulators as required along with fitting of bolted type or compression type tension hardwareas made available (compression machine shall be provided by RVPN on rent free basis),making up at one end, stringing of conductors between the beams with specified sag andtension, also equalizing sag and fitting spacers and spacer T-clamps for twin conductor, forthree phases of conductors in each bus-section.il Single ACSR Panther Section 1094.00 1165.00iil Single ACSR Zebra Section 1274.00 1356.00iiil DoubleACSR Zebra Section 1836.00 1955.00iv) Sinale Tarantulla Section 1145.00 1219.00v\ Double Tarantulla Section 1651.00 1758.00

l:tS.UlXEN-4(CoDtracts)

Page 3 018




2017B. JUMPERS of ACSR and Tarantulla conductor (3 nos. Y- type) between bus to equipment, or

between equipment to equipment or between bus to bus, including transportation ofconductor, disc insulators and hardware from site stores to locations, cleaning and assemblyof disc insulators as required along with fitting of suspension hardwareand erection asrequired, cutting required length of conductor, making connections, fixing of spacers & spacerT-clamps as required, tightening of clamps 1connectors, dressing, etc., for three phases.

u Single ACSR Zebra 1Panther conductor Set 313.00 333.00ii) Double ACSR Zebra conductor Set 625.00 665.00iii) Sinale Tarantulla Set 338.00 360.00iv) Double Tarantulla Set 675.00 719.00

4 STRINGING of Earth wire ( size 7/3.15 mm or 7 14.00 mm ), including transportation of Each 274.00 292.00earthwire, tension hardwares, etc., from site store to locations, laying and cutting requiredlength of earthwire, fitting of bolted type or compression type hardwareas made available(compression machine shall be provided by RVPN on rent free basis ), making up at one end,stringing of earthwire between structure peaks with specified sag and tension, jumpering andconnecting earth bonds, for sinqle earthwire .

5 ERECTION OF SUB-STATION EQUIPMENTSA. i) Erection of 33/0.4 KV or 11/0.4 KV Station transformer up to 500 KVA on existing Each 3726.00 3967.00

masonary platform including transportation of transformer & accessories from site store tolocation erection of Hom Gap fuse set iumoerina from isolator to Hom Gap to transformer.ii) Filteration of the transformer if required (Additional cost) Each 1243.00 1323.00

B. Erection of Current Transformer 1Potential Transformer 1Capacitive voltage Transformer 1Series Reactor 1ResidualVoltage Transformer 1Neutral Current Transformer with clamps &connectors on already erected steel structure including transportation from site store tolocations, fabrication of base frame, fixing of terminal connectors, tightening of nuts & boltsetc., complete in all respects.i) 220 KV CT 1PT 1CVT Nos. 2375.00 2529.00ii}_132KV CT 1PT 1CVT Nos. 1329.00 1415.00iii) 33 KV or 11 KV CT 1PT Nos. 500.00 532.00iv) 33 KV or 11 KV SR 1RVT 1NCT Nos. 954.00 1016.00

C. Erection of LighteningArrestor on already erected steel structure including transportation ofLighteningArrestor, clamps & connectors, surge counter, etc. from site store to locations.fabrication of base frame, fixing of terminal connectors, surge counter. tightening of nuts &bolts etc., complete in all respect.i) 220 KV Nos. 1875.00 1996.00ii) 132 KV Nos. 1336.00 1422.00iii) 33 KV or 11 KV Nos. 298.00 317.00

D. Erection of Isolators on already erected steel structure including transportation of base frame,P. I.'s. contacts. mechanism box, clamps & connectors, etc. from site store to locations. minorfabrication as required, and fixing of terminal connectors, etc.•adjustment! alignment ofisolator and its earth blade, if provided, for their smooth operation and final adjustment ifrequired after jumpering.i) 220 KVa) Without Earth Blade Nos. 4133.00 4400.00b) With Sinale Earth Blade Nos. 4601.00 4899.00c) With Double Earth Blade Nos. 5219.00 5557.00d) Tandem Nos. 4601.00 4899.00

ii)132 KVa) Without Earth Blade Nos. 2438.00 2596.00b) With Single Earth Blade Nos. 2860.00 3045.00c) Tandem Nos. 2860.00 3045.00

iii) 33 KV & 11 KVa) Without Earth Blade Nos. 860.00 916.00b) With Single Earth Blade Nos. 1281.00 1364.00

E. Erection of Wave trap on already erected structure beam. including transportation of wavetrap, disc insulators, hardware. clamps and connectors, etc. from site store to locations.cleaning & assembly of disc insulators alongwith fitting of suspension arrangement anderection, fixing of terminal connectors, etc.i) 220 KV Nos. 758.00 807.00ii) 132KV Nos. 563.00 599.00

XEN-4(Contracts)

Page 4 of8

RAJASTHAN RAJYA VIOHUT PRASARAN NIGAM LTOSCHEDULE OF RATES FOR ERECTION OF UNIT QUANTITY ITEMSOF SUB STATION ON LABOUR CONTRACT BASIS


2017F. Erection of 2x33 KV or 2x11 KV Capacitor Bank, with Series Reactors& ResidualVoltage Each 17344.00 18466.02,.

Transformers / Neutral Current Transformers, including transportation of equipments,structure members, nuts & bolts, washers, clamps & connectors etc. from site store tolocation, assembly of structure, their placing on foundation, levelling and preparing forgrouting as required, but excluding grouting, assembly of capacitor bank cells on frames asrequired & their connections as per manufacturer's drawings, fixing of terminal connectors.

G. Erection of 220 KV or 132 KV Circuit Breakers, including transportation of equipment,structure members, nuts & bolts, clamps & connectors, accessories etc. from site store tolocation, assembly of support structure, their placingon foundation, levelling and preparing forgrouting as required, but excluding grouting, assembly / placing of support columns / poles,mechanism box / control cubicle, and other accessories as per manufacturer's drawings,fitting of SF 6 gas pipeline, fabrication of air / oil pipelineas required,electrical wiring frompole to control cubicle, fixing of terminal connectors as required, but excluding commissioningof CB, for all types of operating mechanism, as required.il220 KV Nos. 18048.00 19216.00iil132 KV Nos. 14298.00 15223.00

H. Erection of 33 KV or 11 KV Circuit Breakers including transportation of equipment, structuremembers, nuts & bolts, clamps & connectors, etc. from site store to location, assembly ofsupport structure, their placing on foundation, levelling and preparing for grouting as required,but excluding grouting, assembly / placing of poles, mechanism box, etc. on support structureas per manufacturer's drawings, fitting of terminal connectors, etc. but excludingcommissioning of CB.n 33 KV or 11KV Outdoor Type ( VCB / SF 6 1 Nos. 6954.00 7404.00ii111 KV Kiosk (VCB / SF 6/ MOCB 1 Nos. 2461.00 2620.00

I. Erection of Post Insulators on already erected structures including transportation of P. I. 's,nuts & bolts, clamps & connectors, etc. from site store to locations, fabrication of base frame& assemblv if required fixinq of clamps etc.

il220 KV Nos. 829.00 883.00iil132KV Nos. 625.00 665.00iiil33 KV or 11 KV Nos. 70.00 75.00

J. Erection of 132 KV Class EHV Transformer (tank already placed on foundation with wheels),including transportation of accessories from site store to locations, erection of HV, IV, LV &Neutral bushings, main & OLTC conservators, radiators, equalizing pipe line, marshallingkiosk, etc. as per manufacturer's drawing, preparationof oil, oil filling, dehydration oftransformer (filter machine, oil tank & operating staff shall be provided by RVPN), electricalwiring from individual equipment, e.g., Buchholz relay, MOLG, OSR, etc. to marshalling kiosk,etc., but excluding testing & commissioning of transformer.allf electricity is available & arranced bv RVPNwithout charqes.

_i1_Transformers received oil filled Nos. 39531.00 42089.00iilTransformers received gas filled Nos. 49531.00 52736.00

b)1f electricity is not available & the Contractor is required to arrange diesel generator ofappropriate caoacttv,ilTransformers received oil filled Nos. 163750.00 174345.00iilTransformers received gas filled Nos. 297969.00 317248.00

K. Erection of 220 KV Class EHV Transformer (Gas filled tank already placed on foundation withwheels), including transportation of accessories from site store to locations, erection of HV,IV, LV & Neutral bushings, erection of cooler bankwith associated pipe line, radiators, fans,pump, main & OLTC conservators, equalizing pipe line, marshalling kiosk, etc. as permanufacturer's drawing, preparationof oil, oil filling, dehydration of transformer along withcooler bank & diverter switch (filter machine, oil tank & operating staff shall be provided byRVPN), electrical wiring from individual equipment, e.g., Buchholz relay, MOLG,OSR, Fans,Pumps, Bushing CT's etc. to marshalling kiosk, etc., but excluding testing & commissioningof transformer.allf electriCityis available & arranged bv RVPNwithout charges. Nos. 120781.00 128596.00b) If electricity is not available & the Contractor is required to arrange diesel generator of Nos. 493438.00 525363.00

appropriate capacity.6 Erection of Control & Relay Panels complete in all respects including transportation from site

store to control room, placing on foundation / cable trench as per layout, interconnectionbetween Control & Relay panels and with existing panels. fixing of side / top covers anddoors, earthing to existing earth strip in control room, connection of bus wiring to existingIpanel and between control and relay panel. as required.

i 2 x 2 Duplex Panel Nos. 2368.00 2521.00ii Duplex Panel Nos. 1188.00 1265.00iii Simplex Panel DC Panel RTCC Panel PLCC Panel etc. Nos. 594.00 632.00iv LT Panel Nos. 1633.00 1739.00

XEN-4(Contracts)

Page 5 018




20177 Erection of Marshalling Kiosk! Line Matching Unit (LMU) I Line Matching & Distribution

Unit (LMDU) complete in all respect including transportation from site store to location,placing on foundation 1cable trench as per layout, preparing for grouting of foundation boltsbut excludino oroutino. etc.i) 220 KV or 132 KV Marshallino Kiosk Nos. 351.00 374.00ii) 33 KV or 11 KV Marshallino Kiosk Nos. 180.00 192.00iiil PLCC LMU 1LMDU Nos. 406.00 432.00

8 Erection of Battery Charger complete in all respect including transportation from site store tolocation olacino on foundation 1cable trench as oer lavout etc.j) 220 Volt DC 400 AH Nos. 1188.00 1265.00ii) 110Volt DC 200 AH Nos. 1188.00 1265.00iiil48 Volt DC 600/400 1200 AH Nos. 1188.00 1265.00

9 BATTERY SETA. Assembly, erection and commissioning of Lead Acid Battery Set including transportation of

cells, battery stand, electrolyte, nuts & bolts and accessories from site store to battery room,assembly of wooden stand, placing the cells on stand, making their interconnection, filling ofelectrolyte, giving two cycle of charge and discharge after initial charging as per procedurerecommended by batterv manufacturer.a) If electricitv is available & arranoed bv RVPNwithout charaes.i) 220 Volt DC 400 AH Nos. 24688.00 26285.00ii) 110 Volt DC 200 AH Nos. 23125.00 24621.00iiif 48 Volt DC 600 1400 1200 AH Nos. 21485.00 22875.00ivl Additional cycle of dlscharce & charce if reauired. Each 4298.00 4576.00

b) If electricity is not available & the Contractor is required to arrange diesel generator ofaoorooriate caoacitv.il 220 Volt DC 400 AH Nos. 85548.00 91083.00ii) 110Volt DC 200 AH Nos. 63985.00 68125.00iii) 48 Volt DC 600/400/200 AH Nos. 43750.00 46581.00iv) Additional cycle of charoe & discharoe if reauired.a) 220 Volt DC 400 AH Each 8594.00 9150.00bl110VoltDC 200AH Each 7188.00 7653.00c) 48 Volt DC 600/400/200 AH Each 5938.00 6322.00

B. Assembly, erection and commissioning of Maintenance Free VRLA type Battery Setincluding transportation of cells, battery stand, nuts & bolts, etc. from site store to batteryroom, assembly of stand, placing the cells on stand, making their interconnection, initialcharging, discharging and final charging as per procedure recommended by batterymanufacturer.al lf electricitv is available & arranoed bv RVPNwithout charaes.i) 220 Volt DC 400 AH Nos. 9180.00 9774.00ii) 110 Volt DC 200AH Nos. 7539.00 8027.00iiil 48 Volt DC 600 1400 1200 AH Nos. 6211.00 6613.00iv) Additional cycle of charae & dlscharae if reauired. Each 4298.00 4576.00

b) If electricity is not available & the Contractor is required to arrange diesel generator ofaoorooriate caoacitv.n220 Volt DC 400 AH Nos. 13320.00 14182.00m 110Volt DC 200 AH Nos. 9805.00 10439.00iiil 48 Volt DC 600 1400 1200 AH Nos. 8476.00 9024.00iv) Additional cvcle of charoe & discharoe if reauired.a) 220 VoltDC 400 AH Each 7188.00 7653.00b) 110Volt DC 200AH Each 5938.00 6322.00c) 48 Volt DC 600/400/200 AH Each 5938.00 6322.00

10 LAYING AND TERMINATION OF CABLESA. Control Cables

i) Laying of P. V. C. insulated unarmoured 1 armoured control cables of 1.1 KV grade withcopper conductor in cable trenches as per specification as required, including transportationof cable drums from site store to locations, laying in cable trenches, cutting to required length,placing them on cable racks 1cable trays 1cable batten & dressing, including removing and refixing trench covers as required, making necessary connections, testing, cable marking onboth the terminating ends, etc., as required for all sizes from 2c x 2.5 sq. mm. to 20c x 2.5 sq.mm, 4c x 4 sa. mm. and 4c x 6 sa. mm.a) Unarmoured control cable. Metres 5.00 5.00b1Armoured control cable. Metres 5.50 6.00

XEN-4(Contracts)

Page 6 of 8

RAJASTHAN RAJYAVIDHUT PRASARAN NIGAM LTD


1) The retes for the erection works given in this BSR are inclusive of all types of labour charges.but exclusive of service tax.sales tax &insurance charges etc.2) The base date for rates given in this schedule is 1 04 2017CODE DESCRIPTION UNIT Rate (Rs); updatedNO. 1.4.2015 Rates (Rs)

2017ii) Fixing of control cables in position with single compression nickel plated brass cable glandsconfirming to IS: 12943 & having three metal washers and one rubber ring. includingpreparation of cable and drilling of corresponding holes in gland plates. etc. as required &including cost of cable glands. for each cable gland of size.al19 mm unarmoured control cable Nos. 41.00 44.00b119 mm armoured control cable Nos. 46.00 49.00c) 25 mm unarmoured control cable Nos. 63.00 67.00d) 25 mm armoured control cable Nos. 69.00 73.00e) 32 mm unarmoured control cable Nos. 90.00 96.00if) 32 mm armoured control cable Nos. 100.00 106.00iii) Termination of wires of cables with copper conductor using copper terminal ends (pin orring type as required of Dowell's or equivalent make as approved by the Engineer- In -Charge) duly crimped with crimping tool. including making wire ends ready for crimping.ferruling & dressing of wires. etc.• as required. including cost of terminal ends for all wires. foreach cable at both ends for cables of the followina sizes.a12c x 2.5 sq. mm. Each 20.00 21.00b) 3c x 2.5 so. mm. Each 30.00 32.00c) 4c x 2.5 sa. mm. Each 40.00 43.00d) 6c x 2.5 sa. mm. Each 60.00 64.00e1l0c x 2.5 sa. mm. Each 100.00 106.00f) 12cx 2.5 sa. mm. Each 120.00 128.00g)16c x 2.5 sa. mm. Each 159.00 169.00h)18c x 2.5 sa. mm. Each 179.00 191.00

In case all the wires of any cable are not got terminated. then a deduction at the rate of Rs.6.00 shall be made for each end of the wires not terminated.il4c x 4.0 so. mm. Each 54.00 57.00i) 6c x 4.0 sa. mm. Each 80.00 85.00k) 4c x 6.0 sa. mm. Each 54.00 57.00I) 6c x 6.0 sa. mm. Each 80.00 85.00

In case all the wires of any cable are not got terminated. then a deduction at the rate of Rs.7.00 shall be made for each end of the wires not terminated.

B. L.T. Power Cablesi) Laying of P. V. C. insulated and P. V. C. sheathed armouredlunarmoured L. T. power cableof 1.1 KV grade with aluminium conductor as per IS: 1255 in ground I cable trench I wall Isurface including transportation of cable drums from site store to locations and excavation of30 cm x 75 cm size trenches. providing 25 mm thick under layer of sand & 2nd class brickcovering & refilling earth in remaining portion. fixing as per approved I available spacing bymeans of M. S. u-clamps, etc. as per specification as required. including making necessaryconnections & testing. etc. as required. of the follOwingsizes.a) 3 Yo core x 70 sq. mm. Metres 41.00 44.00b) 3 Yo core x 120 sa. mm. Metres 41.00 44.00c) 3 Yo core x 185 sa. mm. Metres 50.00 53.00d) 3 Yo core x 300 sa. mm. Metres 50.00 53.00

ii) Fixing of power cables in positionwith single compression. heavy duty nickel plated brasscable glands as per IS: 12943& having three metalwashers and one rubber ring. includingpreparationof cable and drilling of corresponding holes in gland plate. etc.• including cost ofcable gland if required, for each end of cable of size.a) 38 mm. for 3 Yo core x 70 sa. mm. cable with material Nos. 109.00 116.00b) 38 mm. for 3 Yo core x 70 sa. mm. cable without material Nos. 19.00 20.00c) 50 mm. for 3 Yo core x 120 sq. mm. cable with material Nos. 159.00 169.00d) 50 mm. for 3 Yo core x 120 sa. mm. cable without material Nos. 21.00 22.00e) 57 mm. for 3 Yo core x 185 sa. mm. cable with material Nos. 226.00 241.00f) 57 mm. for 3 Yo core x 185 sa. mm. cable without material Nos. 35.00 37.00g) 75/76 mm. for 3 Yo core x 300 sa. mm. cable with material Nos. 415.00 442.00h) 75/76 mm. for 3 Yo core x 300 sa. mm. cable without material Nos. 116.00 124.00

XEN-4(Contracts)

Page 7 olB



1) The retes for the erection works given in this BSR are inclusive of all types of labour charges,but exclusive of service tax,sales tax &insurance charges etc.2) The base date for rates given in this schedule is 1.04.2017.CODE DESCRIPTION UNIT Rate (Rs); updatedNO. 1.4.2015 Rates (Rs)

2017iii)Termination of wires of cables with aluminium conductors using lSI marked tubularaluminium terminal ends as per IS: 8309 duly crimpedwith crimping tool, including makingcable ends ready for crimping and providing insulation tape with colour code, dressing ofwires, etc., including cost of terminal ends if required, for each end of cable (4 nos. per end)for the following size of cables.a) 3 Y, core x 70 sq. mm. cable with material Set 219.00 233.00bl 3 Y, core x 70 sa. mm. cable without material Set 138.00 147.00c) 3 Y, core x 120 sa. mm. cable with material Set 310.00 330.00dl 3 Y, core x 120 sq. mm. cable without material Set 186.00 198.00el 3 Y, core x 185 sq. mm. cable with material Set 465.00 495.00fl 3 Y, core x 185sa. mm. cable without material Set 286.00 305.00g) 3 Y, core x 300 Sq.mm. cable with material Set 770.00 820.00h) 3 Y, core x 300 sq. mm. cable without material Set 361.00 384.00

11 PAINTING OF SUB-STATION EQUIPMENTSAND STEEL STRUCTURESA. Aluminium painting of new steel structures at the GSS including paint and painting brush, Sq. Mtr. 33.00 35.00

emery paper, cloth & solvent, etc. The surface shall be first rubbed free of dust or any otherdeposits on erected M. S. steel structures & beams. One coat of red oxide paint shall beapplied after carrying out cleaning and allowed to dry. Thereafter two coats of Aluminiumpaint shall be applied. Each subsequent coat shall be applied only after the previous coat hasdried. The paint used shall be out of the following recognized manufacturers only, namely,Asian / Nerolac / Berger / Johnson Nicholson / Dulux.

B. Aluminium painting of old painted steel structures at the GSS including paint and painting Sq. Mtr. 24.00 26.00brush, emery paper, cloth & solvent, etc. The surface shall be first rubbed free of dust or anyother deposlts on erected M.S. steel structures & beams.Two coats of Aluminium paint shallbe applied. Each subsequent coat shall be applied only after previous coat has dried. Thepaint used shall be out of the following recognizedmanufacturers, namely, Asian / Nerolac /Berger / Johnson Nicholson / Dulux.

C. Enamel painting on power transformers and other associated equipments using spray Sq. Mtr. 29.00 31.00painting set, including supply of paint, emery paper, cloth & solvent etc. at GSS by cleaningsurfaces thoroughly with soda / caustic solution to clean oily surfaces& thereafter washingwith water. Thereafter two coats of smoke grey syntheticenamel paint shall be applied byspray method. Each coat shall be applied only after the previous coat has dried up. The paintused shall be out of the following recognizedmanufacturers namely, Asian / Nerolac / Berger/ Johnson Nicholson / Dulux. In case of surface area of radiators, the fins will only beconsideredwhich are only feasible and approachable for painting by spray or by brush.

12 Providing and laying in position specffledgrade of cement concrete for all RCC structural Cum 4112 4378.00elements upto plinth level including curing, compaction, finishing with rendering in cementsand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 gradeNominal Mix! Desian Mix.(The rates are as per PWD BSR 2014- Jaipur.)

As per Terms & Rates in the13 SWITCHYARD ILLUMINATION prevailing/applicablePWD

BSR.

XEN -4(Contracts)

Page 801 8

RAJASTHAN RAJYA VIDYUT PRASARAN NIGAM LTD

BASIC SCHEDULEOF RATES FOR REPAIR & MAINTENANCEWORKSEHVLINES& GSS- 2017

1. The rates for the repair and maintenance works given in this BSRare inclusiveof all types of labour charges, but exclusive of service tax, sales tax andinsurance charges etc.

2 The BaseDate for the rates orven in this schedule is01 042017CP.'fi. ~ cpr fcrcRur ~ ~ GX anmR

(2015) (Updated)~ -tr GX 2017)

~-tr

1.1 ~ cpr fcrcRur :-• ~"fI6I' ~ ~ '* Cf)llIh.;111, PIli '"?I01

'Cf)'af, ~, fcrS>'fl'lf q,1ff,~,-qro~oxfroxfro q,!ff, ~ q,!ff, fcrS>'fl'lf lJ6~ .q ~ xf ~ ~ q fCb"llllC'1 cpr-q)m 'C'1'l'TFr cpr ~ I

• PI 1I'"?101 q,1ff ~ ~ 'Cfll1XT '* ~'I!qllJ1'i qftl'$FcPlll (lJ<l ~) ~ cCr ~ I

• ~ ~nillC'1l1 q ~ .qfCb"llllC'1/~ cpr ~ ~ ~ ~~~cpr~ I

• PI 1I'"?I ° 1 q,1ff q ~ ~ q,aTI cCr uc;,~, m~ .q 'C'1'l ~ ~ cCr~I

• \34'<~Cffi ~ .q i{'$1~1'11('g'R~'11) 'Cf))~~I

• ~ ~ ~ ~ 'Cf)) ~"fI6I' ~'4ft'I!:R xf ~ wffiT ~ &T"I!T~~'4X~ I

"1lc :-1. ~ ~ %g ~ '4W ~,

3lIq~1ICf) \34 Cf)'I!01 ~ ~ 'Cf)) ~cCr~'4X~~ I

2. ~ ~ cpr 'ffTl1R ~ fCb"llll C'1,fCb"llllC'1 ~, ~ ~ ~ &T"I!T~~I

3. 'T"fR ~ af?rtnc;r '* ~ '4X fcm:rr~I

1.2 PllI'"?I 01 q,1ff xf ~ &R (fCf) ~ q ~~~~GFIT~~'lt~WT6cCr~&T"I!T~ I~~~~'Cf)) ~ "fI6I' ~ ~ xf ~ ~~&T"I!T~~'4X~ I ~~ %g ~ ~ 3lIq~1ICf) \34 Cf)'I!°1 ~ 'Cf))~cCr~'4X~~ I

Ijh @-~-I I~S) XEN-4(Contracts)

m ~ 100 crt 24.00 26.00~~af?rtnc;r

m ~ 100 crt 4.50 5.00~

AO~ SE(cl;;S-lI)

~ Pagelof15


BASIC SCHEDULEOF RATES FOR REPAIR &MAINTENANCEWORKSEHV LINES& GSS- 2017

CP.xt Cfj"]"(f q;r fctcRur ~ ~ GX" 31WCR GX"(2015) (1.04.201 7)~ ~~~

1.3 mt ~ 3RX qft ~, "i¥T1ffUT -q~, <fq~ q q51"o;g~I'1 m qft ~ &m ~1~~~~cpT~X16r~ 1:Ifu:R ~ ~ wOO ~ &m~ ~ 'R ~ I ~ Cfj"]"(f -gg~ ~ 31lq~llC/') ,,4C/')'I!01 ~ cpT"f<fli flll(1I~C/') 100 crt 5.00 5.00qft ~ 'R ~ 5l7T I 1fR:x

1.4 ~ll"'?lOI "Cflaf, fct~ ¥ q ~ Q"lIQIC1Q

1:Ifu:R ~ ~ qft 00 q ~ "'1lC'Il qft~I ~~~~cpT~ X16r~ 1:Ifu:R ~ ~ wOO~&m~~'R~1~ Cfj"]"(f -gg ~ ~ 31lq~llC/') ,,4C/')'I!01 ~ 100 crt 4.50 5.00~ cpT"f<fli qft ~ 'R ~ 5l7T I 1fR:x

1.5 ~ifqT~~~3RX~~"Cf)"'I!"'1Tq~~~~cpT~X16r~ 1:Ifu:R ~ ~ wOO ~ &m~~'R~q~~:~ Cf)'I!" <fq ~ CIl"fl:ffi WTT'1T I~ Cfj"]"(f -gg ~ ~ 31lq~llC/') ,,4C/')'I!01~ cpT"f<fli qft (YI1l"Rf 'R "C1""A 5l7T I ~ "'I!f.17T 3.60 4.0031 ) 0.6 1fR:x ('[Cf) ~qft~ ~ 1fR:x, I"ij ) 0.6 1fR:x ~ 1.2 1fR:x ('[Cf) ~qft ~ "'I!f.17T 5.60 6.00~ ~ 1fR:x, I~ ) 1.2 1fR:x ~ ~ ~ qft <fq I ~ "'I!f.17T 7.50 8.00

~ 1fR:x1.6 ~ X16r~ ~ ft<rq mt "lf ~ t:rffi,

C/')Iecm ~, ~ ~ "4'Im m ~~ ,,'<SII'$C/')'I! ~ ~ q;r Cfj"]"(f q ~Cfj"]"(f ~ ~ \ilT m ~ qft <Tt m~~:~"Cf)"'I!"'1TI~~~~ cpT~ X16r~ 1:Ifu:R ~ ~wmT~&m~~'R~I ~ Cfj"]"(f -gg ~ ~ 31lq~llC/') ,,4C/')'I!01~ cpT"f<fli qft (YI1l"Rf 'R "C1""A 5l7T I3l)~Iff?r(~m~q~: ~ 100 crt 171.00 182.00WTT'1T ~ 1fR:x

~ ~ "lf wfTrc;r -;:fflT ~ I)~ 100 crt 111.00 118.00

"ij ) 31 '1 ~ q c;\S Iff?r ~ 1fR:x

cd--XEN -4(Contracts)

~)SE(~tIacts- II)

Page 2 of1S

RAJASTHAN RAJY A VIDYUT PRASARAN NIGAM LTD

BASIC SCHEDULEOF RATESFOR REPAIR & MAINTENANCEWORKSEHV LINES& GSS- 2017

1. The rates for the repair and maintenance works given in this BSRareinclusiveof all types of labour charges, but exclusiveof service tax, salestax and insurancecharges etc.

2. TheBaseDate for the ratesgiven in thisschedule is01.04.2017

CODE DESCRIPTIONNO.

UNIT RATE UPDATED BSR(Rupees) RATE-l.04.20171.04.2015 (Rupees)

1 22.0 PAINTING OF STRUCTURES & EQUIPMENTS

2.1 PAINTING OF UNPAINTED STEELSTRUCTURES:Aluminium painting of unpainted steelstructures at the GSSincluding paint andpainting brush, emery paper, cloth &solvents, etc. The surface shall be firstcleaned with wire brush/ emery paper andthereafter wiped with cloth to remove rustand dust or any other deposits on erectedM.S.Steel structures& beams. One coat ofred oxide paint shall be applied aftercarrying out cleaning and allowed to dry.Thereafter, two coats of aluminum paintshall be applied. Each subsequent coatshallbe applied only after the previouscoathas dried up. Thepaints used shall be fromany of the following recognizedmanufacturers, namely Asian/ Nerolac/Berqer/JohnsonNicholson.

2.2 PAINTING OF OLD PAINTED STEELSTRUCTURES:Aluminium painting of old painted steelstructures at the GSSincluding supply ofpaint and painting brush, emery paper,cloth & solvents, etc. The surface shall befirstcleaned with wire brush/ emery paperand thereafter wiped with cloth to removerust and dust or any other deposits onerected M.S.Steel structures.Two coats ofaluminum paint shall be applied. Eachsubsequent coat shall be applied only afterthe previous coat has dried up. The paintsused shall be from any of the followingrecognized manufacturers, namely Asian/Nerolac /Berger/JohnsonNicholson.

Sq.metre

Sq.metre

AE~

3 4 5

39.00 42.00

XEN -4(Contracts)

30.00 32.00

SE(~tS-II)

Page 3 of15



1 52 3

2.3 PAINTING OF TRANSFORMERS & EQUIPMENTS:Enamel painting on power transformers andother equipments including supply of paintand spray painting set, emery paper, cloth &solvents, etc. at GSS by cleaning surfacethoroughly with soda / caustic solution toclean oily surface and thereafter washing withwater. Thereafter, two coats of smoke graysynthetic enamel paint shall be applied byspray method. Each subsequent coat shall beapplied after the previous coat has fully driedup. The paints used shall be from any of thefollowing recognized manufacturers, namelyAsian/ Nerolac /Berger/Johnson Nicholson. Incase of surface area of radiators, those finswillonly be considered which are actuallyfeasible and approachable for painting byspray or by brush.

Sq.metre

4

31.00

3.0

33.00

Maintenance of Bay Equipments

Providing of work assistance as given below inMaintenance work of following bayequipments such as Circuit Breaker, CurrentTransformers, Lightning Arrestors, Isolators,CVTs, PLCC equipments and correspondingControl and Relay Panels. (All spares,lubricating material and only special T&Pshall be provided by RVPN.Cleaning materialand general T&P shall be arranged by thecontractor.)a) Checking of tightness of clamps &

connectors.b) Cleaning of all insulators.c) Attending to oil leakage, if any.d) Cleaning of all Junction Boxes and

secondary terminal boxes.e) Checking of operation of CB through

relays and verifying various logic andcontrol circuits and annunciation circuits.

f) Measurement of CBoperation timings.g) Checking of Isolator operation and its

alignments.h) Checking of gas pressureslike SF6 & N2 in

circuit breokers/Cls. etc.

AE{Jp:; cd-XEN-4( Contracts) SE(~cts-n)

Page 4 of15


BASIC SCHEDULE OF RATES FOR REPAIR & MAINTENANCE WORKSEHV LINES & GSS - 2017

1

33 or 11 KV bay (1 No. Supervisor + 5 Nos. Each BayWorkmen)

2

i) Measurement of IR values of LAs, CTs andCVTs.

j) Lubrication of defined parts of allequipments all required points.

k) Washing the equipments. In case oil stainsare present, then washing is to be donewith use of detergent solution.

I) Cleaning of C&R panel from inside.m) Providing other related work assistance as

may be required by Incharge.

3.1

3.2

3.3

3.4

400 KV bay (1 No. Supervisor + 10 Nos. Workmen)



Each Bay

Each Bay

Each Bay

4.0 Maintenance of Power TransformersProviding of work assistance as given below inMaintenance of Power Transformers for thefollowing types of Power Transformers. (Allspares, lubricating material and only specialT&P shall be provided by RVPN. Cleaningmaterial and general T&P shall be arrangedby the contractor.)a) Cleaning of porcelain of bushings.b) Checking of tightness of clamps &

connectors.c) Cleaning of Buchholz & oil surge relays.d) Cleaning of glasses of all oil level

indicators.e) Cleaning of marshalling box, cooler

control cubicle, thermometer, etc., asprovided.

f) Attending to oil leakage from Tr. Body &Bushings.

QJ Checking of oil level in oil filled bushlnqs.

A~XEN-4(Contracts)

3 4

3466.00

2915.00

2365.00

2083.00

5

3690.00

3104.00

2518.00

2218.00

SE~ts-II)

Page 5 of15



1 2 3 4 5

Measurement of earth resistance.Testing of PRDChecking of tripping circuits of Buchholz &WDG, oil temperature controls andProtection scheme.

m) Checking of OLTC gear operations.n) Checking of auto circuits of cooling bank.0) Taking of oil samples for testing.p) To carryout other special measurements as

may be required.q) Providing of other related work assistance

as may be required by Work Incharge.4.1 400/220 kV, 315 MVA or 250 MVA

( 8 Nos. Workmen)220/132 kV, 100 MVA or 50 MVA and 220/33 kV,50 MVA or 35 MVA(6 Nos. Workmen)132/33 kV & 132/11 kV (All capacities)(5 Nos. Workmen)33/11 kV & Aux. supply station Transformer(3 Nos. Workmen)

4.2

4.3

4.4

h) Checking of Drycol air drying system.i) Measurement of I.R.values.j)k)I)

EachTrf.EachTrf.

EachTrf.EachTrf.

2246.00

1696.00

1525.00

968.00

2391.00

1806.00

1624.00

1031.00

5.0 Maintenance of Bus Bars and AssociatedEquipmentsProviding work assistance as given below inmaintenance work of Bus bars of variousvoltage levels. (All spares, lubricating materialand only special T&P shall be provided byRVPN. Cleaning material and general T&P shallbe arranged by the contractor.)

a) Tightening of clamps & connectors onoverhead bus conductors and gantries (at amaximum height of 25 metre usingsafety belts).Also, tightening of clomp/ connectors of all busside associated equipments.

b) Replacement of worn out clamps &connectors of bus during work under item No.(a).

c) Cleaning of all insulators of suspension andtension stringsof bus bars and insulators of busisolators,BusCVT's/PT's

&J--XEN-4(Contracts)

~vSE(Co tracts-II)

Page60f15


BASIC SCHEDULEOF RATES FOR REPAIR &MAINTENANCEWORKSEHVLINES& GSS- 2017

400 KV BusSection

5.1 (1 No. Supervisor + 8 Nos. Workmen)

220 KV BusSection


132 KV BusSection


33 KV or 11 KV Bussection


6.0 Dehydration/ replacement of transformer oil.

6.1 Filtration of Oil and Dehydration of Transformer:

6.1.1 Setting up and winding up.

6.1.2 Running the filter machine till required oil values Per dayare attained.

1 2d) Checking of operation of Busisolators and their

alignment including motorized operation.e) Maintenance of operating mechanism &

switches, etc.f) Lubrication of all moving parts.g) Providing of other related work assistance as

may be required by Work Incharge.

Providing work assistance for filtration of oil anddehydration of transformers of all ratingsincluding setting up of the filter machine,making connections of LT supply, makingconnections of oil pipelines, providing 3 Nos.semi skilled workmen for assistance in operationof filter machine in three shifts till the required oilvalues are attained and removal of pipes andLT supply after the work is completed. Filtermachine and operating staff shall be providedby RVPN.

A

Each job 2023.00 2154.00

Each

section

Each

section

Each

section

Each

section

XEN -4(Contracts)A~

3

887.00

54

2983.00 3176.00

2425.00 2582.00

1808.00 1925.00

1689.00 1798.00

833.00

SE(clts-II)Page 7 of 15


BASIC SCHEDULEOF RATES FOR REPAIR&MAINTENANCEWORKSEHV LINES& GSS- 2017

1 26.2 Replacement of Oil & Dehvdration of Oil and

Transformer:Providingwork assistancefor replacement andfiltration of oil of the following quantities anddehydration of oil and transformersof all ratingsincluding setting up of the filter machine,making connections of LT supply, makingconnections of oil pipelines, providing 3 Nos.semiskilledworkmen for assistancein operationof filtermachine in three shiftstill the required oilvalues are attained and removal of pipes andLT supply after the work is completed.Assistance shall also be provided fortransporting new oil from GSSstore to filtermachine, filling into oil tanks, filtration of oil,draining of oil from transformerand filling intooil drums,fillingof new oil in transformerand itsfiltration and depositing drumsof old oil in theGSSstore.Allwork shallbe within GSSpremises.Filtermachine, operating staff, oil tank, cranefor handling oil tank, truck/tractor trolley fortransportation,etc. shallbe provided by RVPN.

6.2.1 Settingup and winding up6.2.2 Handlingof oil asabove

6.2.3 Runningthe filtermachine till required oil valuesare attained.

6.3 Maintenance of TransformerduringReplacement of Oil:Providing work assistance in maintenance oftransformer during replacement of oil. Thework includes opening of inspectioncover/man holes,flushingof windingswith hotoil, draining of oil at bottom of tank, removal ofsludge & cleaning of bottom of tank,attending to leakages in transformer,fabrication of gasketsas required and

XEN -4(Contracts)

Eachjob 2023.00PerkLof 126.00trf. Oilcapacity asperratingplatePerday

3

887.00

54

2154.00134.00

833.00

SE(d;ctS-II)

Page8 ofl5



1 2 3 4 5replacing old and damaged gaskets,cleaning of transformer tank after above workis completed and any other associated work(excluding oil handling and work related togaskets of main tank cover and bushings of132 kV & above) assigned by the GSS-Incharge for following voltage class oftra nsformers.(All spares, lubricating material and only specialT&Pshall be provided by RVPN.Cleaning materialand general T&Pshall be arranged by thecontractor.)

6.3.1 400 kV class Transformers6.3.2 220 kV class Transformers6.3.3 132 kV class Transformers6.3.4 33 kV class Transformers ( including station

auxiliary transformer)7.0 MAINTENANCE OF EHV LINES7.1 ROUTINE PATROLLING OF LINES AND REPORT

SUBMISSION:Routine Patrolling/Inspection of 400 kV/ 220 kV/132 kV lines including detailed inspection withbinocular (to be arranged by Contractor). Theinspection/ checking is to be done as perdirections/ instructions in the erstwhile RSEBMaintenance Manual for Transmission Lineswhich includes checking of the following:a) Towers & structures, their foundations,

revetment, earthing, tower members, nutsand bolts, etc.

b) Conductors and earth wire and theiraccessories / hardware.

c) Horizontal & Vertical clearances ofconductors.

A report of the patrolling/inspection is to beprepared in the proforma prescribed in theabove manual/ISO documents. Transport andhalting arrangement as required shall be madeby the Contractor at his own cost.

7.2 BREAKDOWN / EMERGENCY PATROLLING OFLINES:Breakdown / emergency Patrolling of 400 kV /220 kV /132 kV lines for locating the fault andassessing the damage, if an_y.

EachEachEachEach

PerrouteKm

Perroutekm.

2246.001696.001525.00968.00

20l.00

250.00

2391.001806.001624.00103l.00

214.00

266.00

cd--XEN-4(Contracts) SE(C~cts-II)

Page 9 of15



1

Per jobPer jobPer job

3 4 52


7.3 REPAIROF ACSRCONDUCTORi) Work assistance in repair of ACSRconductor including

lowering down conductor at suspension points toground and/providing Repair sleeve/ Armour Rod/Suspension clamps/related works and re-fitting ofconductor (All material and only special T&Pshall bearranged by RVPN.General T&Pshall be arranged bythe contractor.)(a) Moose (13 Nos. Workmen)(b) Zebra (11 Nos. Workmen)(e) Panther (8 Nos. Workmen)


3481.002915.002246.00

3706.003104.002391.00

ii) Work assistance in repair of ACSRconductor includingcutting & providing compressed joint in caseconductor is found damaged, and restringing ofconductor. (All material and only special T&Pshall bearranged by RVPN.General T&Pshall be arranged bythe contractor.(a) Moose (15 Nos. Workmen)(b) Zebra (13 Nos. Workmen)(e) Panther (11 Nos. Workmen)

4105.003481.002915.00

4371.003706.003104.00

7.4 REPLACEMENTOF DISC INSULATORS:Work assistance in replacement of disc insulators asgiven below including lowering / tensioning / re-sag ofconductor as applicable. (All material and onlyspecial T&Pshall be arranged by RVPN.General T&Pshall be arranged by the contractor.)

ti) 400 kV Linesa) Suspension Tower (11 Nos. Workmen)b) Tension Tower (15 Nos. Workmen) Per string 2915.00

Per string 4105.003104.004371.00

(ii) 220 KV linesa) Suspension Tower (8 Nos. Workmen)b) Tension Tower (11 Nos. Workmen)

Per string 2246.00Per string 2915.00

2391.003104.00

(iii) 132 KV linesa) Suspension Tower (7 Nos. Workmen)b) Tension Tower (11 Nos. Workmenl

Per string 1793.00Per string 2915.00

1909.003104.00

7.5 RESTRINGINGOF EARTHWIRE: Work assistance inrepair of Earth wire including restringing of Earth wireafter providing necessary joints and additional/ newEarth wire, if required. (All material and only specialT&Pshall be arranged by RVPN.General T&Pshall bearranged by the contractor.)(a) 7/3.66 mm (400 KV) (13 Nos. Workmen)(b) 7/4 mm (220 KV) (11 Nos. Workmen)(e) 7/3.15 mm (132 KVl (8 Nos. Workmen)

3481.002915.002246.00

3706.003104.002391.00

&l-XEN-4(Contracts) SE(~cts-II)

Page 10 of15


BASIC SCHEDULE OF RATES FOR REPAIR & MAINTENANCE WORKSEHV LINES & GSS - 2017

i) Girth upto 300 mm. Each 45.00 48.00

ii) Girth above 300 mm to 600 mm. Each 96.00 102.00

iii) Girth above 600 mm to 900 mm. Each 165.00 176.00

iv) Girth above 900 mm to 1800mm. Each 330.00 351.00

v) Girth above 1800mm to 2700 mm. Each 633.00 674.00

vi) Girth above 2700mm to 4500 mm. Each 1295.00 1379.00

vii) Girth above 4500 mm. Each 3824.00 4071.00

8.0 Maintenance of D.C. SystemProviding work assistance for the work ofmaintenance of D.C. System includingdistribution boards, battery banks and chargersof various capacities.

17.6

2CUTTINGOF TREESINCLUDING CUTTINGOFTRUNKS,BRANCHESAND REMOVAL OF STUMPS:Cutting of trees including cutting of trunks,branches and removal of stumps and roots,refilling, compaction of backfilling and stackingof serviceable material by manual means withall lifts.

i} To take readings of voltage of all batterycells.

ii} To take readings of specific gravity of allbattery cells (for conventional type).

iii} To check electrolyte level of all cells andtopping up if required ( for conventionaltype).

iv} Checking temperature of cells.v} Checking and cleaning of terminals& lugs.vi} Application of petroleum jelly on terminals.vii} Checking capacity by switching off battery

charger as per RVPN procedure andcharging of batteries by Boostcharging.

viii} Cleaning of chargers and its componentsfrom insideby blower.

ix) Cleaning of DCdistributionboard.

XEN -4(Contracts)

3 54

SE(ltracts-ll)

Page 11 of15



8.1 220 Volts DC system with conventional type Each set 1071.00 1140.00battery set. (4 Nos. workmen)

8.2 110 Volts DC system with conventional type Each set 848.00 903.00battery set. ( 3 Nos. workmen)

8.3 48 Volts DC system with conventional type Each set 625.00 665.00battery set. ( 2 Nos. workmen)

8.4 220 Volts DC system with VRLA type battery set. Each set 848.00 903.00( 3 Nos. workmen)



8.7 Boost charging of 220/110/48 Volts battery set. Per day 1175.00 1251.00( 4 Nos. workmen)

9.1 Laying or removing of cables: The work coversloading and unloading of control cables in drumsfrom store to site, placing the control cable drumson turn table and laying of the required length ofthe control cable between specified locations andcutting them as directed. It also covers placing &dressing them in cable racks in trenches byremoving trench covers and putting them back.(Material and only special T&Pshall be providedby RVPN.General T&P shall be arranged by thecontractor.)

9.0 MAINTENANCE OF POWER& CONTROLCABLES

18.0

9.1.1

9.1.2

9.1.3

2Maintenance of D.C. Systemx) Cleaning of battery cases and battery

stand including insulators.(All spares, lubricating material and onlyspecial T&P shall be provided by RVPN.Cleaning material and general T&P shall bearranged by the contractor.)

2 core to 19 core 2.5 Sq.mm. to 6 Sq.mm.(control cable)3 core or 3V2 core 35 Sq.mm. to 50 Sq.mm.(power cable)3 core or 3V2 core 70 Sq.mm. to 120 Sq.mm.(power cable)

PermetrePermetrePermetre

ci-XEN -4(Contracts)

3

16.00

54

7.50 8.00

7.50 8.00

15.00

SE(~ctS-II)

Page 12 of15


BASIC SCHEDULEOF RATESFOR REPAIR &MAINTENANCEWORKSEHV LINES& GSS- 2017

1 2 3 4 59.1.4 3 core or 3V2 core 185 Sq.mm. to 300 Sq.mm. Per 23.00 24.00

(power cable) metre9.1.5 1 to 12 pair, 0.5 Sq.mm. to 1.5 Sq.mm. (PLCC Per 3.80 4.00

cable) metre9.2 Providing of work assistance for cable end

termination of control cables, power cablesand PLCC cables of various sizes. The workcovers stripping the insulation at both ends,fixing the cable in cable glands and then ongland plates and tagging them, ferruling,crimping lugs and connecting the cores onboth the ends in terminal block.(Material and only special T&P shall beprovided by RVPN. General T&P shall bearranged by the contractor.)

9.2.1 2 core to 19 core 2.5 Sq.mm. to 6 Sq.mm. Per 23.00 24.00(control cable) cable

bothends

9.2.2 3% core 35 Sq.mm. (power cable) -00- 53.00 56.009.2.3 3V2 core 50 Sq.mm. (power cable) -00- 64.00 68.009.2.4 3V2 core 70 Sq.mm. (power cable) -00- 71.00 76.009.2.5 3V2 core 95 Sq.mm. (power cable) -00- 93.00 99.009.2.6 3V2 core 120 Sq.mm. (power cable) -00- 115.00 122.009.2.7 3V2 core 185 Sq.mm. (power cable) -00- 201.00 214.009.2.8 3V2 core 240 Sq.mm. (power cable) -00- 201.00 214.009.2.9 3V2 core 300 Sq.mm. (power cable) -00- 253.00 269.009.2.10 1 to 12 pair, 0.5 Sq.mm. to 1.5 Sq.mm. (PLCC -00- 23.00 24.00

cable)

SE(~ts-n)

Page 13 of15

XEN -4(Contracts)



110.0 EMERGENCYMAINTENANCE OF SUBSATION

2 3 54

Providing work assistance in attendingemergency maintenance works of 400 kV/220kV/132 kV GSS for various equipments like,power transformers with associated controls &accessories, breakers, isolators, bus bars,air/gas system, CT's, CVT's/PT's, LA's, auxiliarypower supply system & D.C. system onfollowing basis.(All spares, lubricating material and onlyspecial T&P shall be provided by RVPN.Cleaning material and general T&P shall bearranged by the contractor.)

10.1 400 kV Sub Station Per day 4016.00 4276.0( 10 Nos. Workmen)



11.0 Maintenance of LTsystem and yard lightsProviding work assistance for maintenance of LTsystem and yard lights and other work.Work details

1. Maintenance of LTswitchgear bywithdrawal and insertion of LTincomermodules.

2. Opening & refixing, replacement or repair ofdamaged/worn out parts.

3. Replacement of fuses, all fused bulbs, tuberods, HPSVlamp, HPMV lamp, indicatinglamps, Amp. meter and Volt meter etc.

4. Replacement/repairs of defective switches& fixtures in Control Room building and yard.Tightening & cleaning of fixture covers.

5. Changing of defective ballasts, ignitors,starters, condensers etc.

6. Replacement/repair of ceiling fans &re_gulators.

Gi--XEN-4(Contracts)

V~J,../SE(Co~tracts-II)

Page 14 of15I



1

(All spares, lubricating material and onlyspecial T&P shall be provided by RVPN.Cleaning material and general T&P shall bearranged by the contractor.)

3 4 5

11.111.211.3

27. Replacement/ repair of electrical wiring,

cable in Control Room building and yardincluding minor extension of wiring andfittings.

8. To provide work assistance in any otherworks related to maintenance of LTsystemand yard lights as may be required by workIncharge.

At 400 kV GSS (3 days in a quarter)At 220 kV GSS (2 days in a quarter)At 132 kV GSS (1 day in a quarter)

XEN -4(Contracts)

Per dayPer dayPer day

618.00618.00618.00

658.00658.00658.00

SE(Cl:S-II)

Page 15 of15A~

id. ys - rajasthan · asthan rajya vioyut prasaran nigam lto. corporate identity number...

Documents