imp visit july 10, 2013 matt hoff lbnl july 18, 2013
TRANSCRIPT
![Page 1: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/1.jpg)
IMP Visit July 10, 2013
Matt Hoff LBNL July 18, 2013
![Page 2: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/2.jpg)
Bad cut-back machining
Note the scribe line showing the cut-back angle
![Page 3: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/3.jpg)
Vane cut-back repair #2To be ebeam welded along the curved joint
![Page 4: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/4.jpg)
The dropped and bent vane
Bent like this
![Page 5: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/5.jpg)
Adjustable tuners
![Page 6: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/6.jpg)
Half length module with adjustable tuners and hoist rings
![Page 7: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/7.jpg)
Temporary cut-back blocks
![Page 8: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/8.jpg)
Adjustable end tuners RF spring slot
![Page 9: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/9.jpg)
Flat plate used to bring the four vanes together
![Page 10: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/10.jpg)
Bead pull set-up
North side
South side
![Page 11: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/11.jpg)
Beads
![Page 12: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/12.jpg)
Ebeam weld test pieces. Checking for good penetration. All the samples looked good.
![Page 13: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/13.jpg)
Module 2. Note the RF port. Note the tapped holes on the side for bolting
![Page 14: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/14.jpg)
Lifting fixture similar to our U-bracket design.
Steel pallets for holding the vanes. Similar to what we showed them.
![Page 15: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/15.jpg)
Note all the extra holes to bolt the vanes together for brazing
Safety hazard?
![Page 16: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/16.jpg)
Lifting brackets bolted to the copper to handle the rough machined vanes. The tapped holes are shallow. Not allowed at LBNL
![Page 17: IMP Visit July 10, 2013 Matt Hoff LBNL July 18, 2013](https://reader035.vdocument.in/reader035/viewer/2022062314/56649f4c5503460f94c6cded/html5/thumbnails/17.jpg)
A test RFQ with water lines