incremental rotary encoder e outgoing conne rotary encoder ... e80 instrukcija.pdf · e40s e40h...
TRANSCRIPT
E40S E40H E40HB E80H
ROTARY ENCODER(INCREMENTAL TYPE)
E40S/E40H/E40HB/E80H SERIESM A N U A L
Thank you very much for selecting Autonics products. For your safety, please read the following before using.
▣ Specifications ▣ Connections
▣ Caution for using
▣ Output waveform
▣ Dimensions
▣ Major products
1. In case of using this unit with machinery(Medical equipment, vehicle, train, airplane, combustion apparatus, entertainment processing equipment, conveyor, elevator or safety device etc.), it is required to install fail-safe device, or contact us for information on type required.It may cause serious human injury or a fire, property.
▣ Caution for your safety
Warning
※Please keep these instructions and review them before using this unit.
※Please observe the cautions that follow;
Warning Serious injury may result if instructions are not followed.
※The following is an explanation of the symbols used in the operation manual.
: Injury or danger may occur under special conditions.
1. Do not drop water or oil on this unit.It may cause damage or miscontrol due to malfunction.
2. Please observe voltage rating.It may shorten the life cycle or damage to the product.
3. Please check the polarity of power and wrong wiring.It may result in damage to this unit.
4. Do not short circuit the load.It may result in damage to this unit.
Caution
Caution Product may be damaged, or injury may result if instructions are not followed.
▣ Outline
▣ Ordering information
▣ Control output diagram
This unit is very useful to control position and speed by converting revolution value of shaft into number of pulse as an optical incremental Encoder.
◎Shaft type(E40S) ◎Hollow shaft type(E80H)
◎Hollow shaft type(E40H)
◎Hollow shaft built-in type(E40HB)
(Unit:mm)
1. Installation① This unit is consisted of precision components. Therefore please treat this product carefully.② When you install this unit, if eccentricity and deflection angle are larger, it may shorten the
life cycle of this unit.
2. Environment Please do not use this unit with below environment, it results in malfunction.
① Place where this unit or component may be damaged by strong vibration or impact.② Place where there are lots of flammable or corrosive gases.③ Place where strong magnet field or electric noise are occurred.④ Place where there is beyond of rating temperature or humidity⑤ Place where strong acids or alkali near by.⑥ Place where there is the direct ray of the sun.
3. Vibration and Impact① When the strong impact loads on this unit, the error pulse may occur as if the slit is revolving. ② Therefore please fix bracket firmly when mount this unit, because Rotary encoder with high
resolution can be easily affected by impact.
4. Wire connection① Do not apply a tensile strength in excess of 30N to the cable.② When a high voltage or power line pass near by the encoder cable, be sure to wire the
encoder cable in separated conduit to prevent malfunction. ③ When extend the cable, please use it after checking the cable and response frequency due to
increment of residual voltage or distortion of waveform can be easily occurred. (Preferable shortest distance for operating)④ Shield wire must be connected to F.G. terminal.
※It may cause malfunction if above instructions are not followed.
◎Normal type ◎Cable outgoing connector type
※ Non-using wires must be insulated.※ The shield cable and metal case of encoder
must be grounded(F.G.).
Incremental Rotary encoder ø 40mm Shaft type ø40mm Hollow shaft type ø40mm Hollow shaft Built- in type ø80mm Hollow shaft type
Model
Totem Pole output E40S - - -T- E40H - - -T- E40HB - - -T- E80H - - -T-
NPN open collector output E40S - - -N- E40H - - -N- E40HB - - -N- E80H - - -N-
Voltage output E40S - - -V- E40H - - -V- E40HB - - -V- E80H - - -V-
Line Driver output E40S - - -L- E40H - - -L- E40HB - - -L- E80H - - -L-
Resolution(P/R)*1, *2, *5, 10, *12, 15, 20, 23, 25, 30, 35, 40, 45, 50, 60, 75, 100, 120, 125, 150, 192, 200, 240, 250, 256, 300, 360, 400, 500, 512, 600, 800, 1000, 1024, 1200, 1500, 1800, 2000, 2048, 2500, 3000, 3600, 5000 (Not indicated type is available to customize)
60, 100, 360, 500, 512, 1024, 3200
Output phase(※1) (※1) A, B, Z phase(Line Driver output: A, A, B, B, Z, Z phase)
Ele
ctric
al specific
ation
Phase difference between output Output between A and B phase: T 4
± T 8
(T= 1cycle of A phase)
Control outp
ut
Totem Pole output● Low ☞ Load current: Max. 30mA, Residual voltage: Max. 0.4VDC● High ☞ Load current: Max. 10mA, Output voltage(Power voltage 5VDC): Min.(Power voltage-2.0)VDC, Output voltage(Power voltage 12-24VDC): Min. (Power voltage-3.0)VDC
NPN open collector output Load current: Max. 30mA, Residual voltage: Max. 0.4VDC
Voltage output Load current: Max. 10mA, Residual voltage: Max. 0.4VDC
Line Driver output● Low ☞ Load current: Max. 20mA, Residual voltage: Max. 0.5VDC ● High ☞ Load current: Max. -20mA, Output voltage(Power voltage 5VDC): Min. 2.5VDC, Output voltage(Power voltage 12-24VDC): Min. (Power voltage-3.0)VDC
Resp
onse
time(R
ise/F
all)
Totem Pole output
Max. 1㎲ (Cable length: 2m, I sink=20mA)NPN open collector output
Voltage output
Line Driver output Max. 0.5㎲ (Cable length: 2m, I sink=20mA)
Max. Response frequency 300k㎐ 200k㎐
Power supply ● 5VDC ±5%(Ripple P-P: Max. 5%) ● 12-24VDC ±5%(Ripple P-P: Max. 5%)
Current consumption Max. 80mA (disconnection of the load), Line Driver output: Max. 50mA(disconnection of the load)
Insulation resistance Min. 100㏁(at 500VDC megger between all terminals and case)
Dielectric strength 750VAC 50/60㎐ for 1 minute(Between all termials and case)
Connection Cable outgoing type, 250mm Cable outgoing connector type
Mechanic
al
specific
atio
n Starting torque Shaft Type: Max. 40gf.cm(0.004N.m), Hollow Type: Max. 50gf.cm(0.005N.m) Max. 200gf.cm(0.02N.m)
Moment of inertia Max. 40g.cm2(4×10-6kg.m2) Max. 800g.cm2(8×10-5kg.m2)
Shaft loading Radial: 2kgf, Thrust: 1kgf Radial: 5kgf, Thrust: 2.5kgf
Max. allowable revolution(※2) 5,000rpm 3,600rpm
Vibration 1.5㎜ amplitude at frequency of 10~55㎐(for 1 min.) in each X, Y, Z direction for 2 hours
Shock Max. 50G Max. 75G
EnvironmentAmbient temperature -10 ~70℃, Storage: -25 ~ 85℃
Ambient humidity 35 ~ 85% RH, Storage: 35 ~ 90%RH
Protection IP50(IEC Standards)
Cableø5mm, 5P, Length: 2m, Shield cable(Line Driver output: ø5mm, 8P)
(AWG 24, Core wire diameter: 0.08mm, No. of core wire: 40, Insulator out diameter: ø1mm)
Accessory ø6mm coupling(Standard), ø8mm coupling(Option) Bracket
Approval (Except for Line Driver output)
Unit weight Approx. 120g Approx. 560g
※ 1: 1, 2, 5, 12 P/R are output A, B phase only.(But Line Driver output: A, A, B, B phase)
※ 2: Max. allowable revolution≥ Max. response revolution [Max. response revolution(rpm) = Max. response frequency
Resolution×60 sec.] Please select the resolution to make lower max. revolution than max. allowable revolution.
※ Environment resistance is rated at no freezing or condensation.
A Tolerance
ø6-0.01-0.015
ø8-0.01-0.02
A ø6 ø8 ø10 ø12
B ø15 ø17
Tolerance+0.015-0
Cable for normal type
ø5, 5P(Line Driver output: 8P), Length: 2000, Shield cable
Cable for normal type
ø5, 5P(Line Driver output: 8P), Length: 2000, Shield cable
Cable for normal type
ø5, 5P(Line Driver output: 8P), Length: 2000, Shield cable
A
AB
ø40
ø40
ø20
+0
-0.0
2
32
31 20
15
10
45̊
45̊
3-120˚
3-M3×0.5
DP: 5
P.C.D. 30
88.5
±1
7 16.2
5
24
22
2-R1.5
R1.75
15̊
R3
63.5
12
24
8
t = 0.260̊
30̊
18
ø18
8
2-ø3.4
6-ø3.4
P.C.D. 30
P.C.D. 46R27
s = 0.5㎜ Max.
ε= 0.25㎜ Max.
θ = 5̊ Max.
● When combine the coupling to encoder shaft, if there is big
eccentricity or bend between rotating encoder shaft and mate
shaft, it will make the life cycle of encoder and coupling shorten.● It must not use larger shaft loading than specification.
θ
ø6mm: 4 - M3×0.5
ø8mm: 4 - M4×0.7
ε
27
8
A B
ø40
32
45̊
8
C
D s
C±s
Cable for normal type
ø5, 5P(Line Driver output: 8P), Length: 2000, Shield cable
3.5
1244.5
43
35 6
ø80
30̊
15̊
● Totem Pole output● NPN open collector output● Voltage output
Black: OUT AWhite: OUT BOrange: OUT ZBrown: +V(5VDC, 12-24VDC ±5%)Blue: GND(0V)Shield: F.G.
● Line Driver output
Black: OUT ARed: OUT AWhite: OUT BGray: OUT BOrange: OUT ZYellow: OUT ZBrown: +V(5VDC, 12-24VDC ±5%)blue: GND(0V)Shield: F.G.
● Totem Pole output● NPN open collector ouput● Voltage output
● Line Driver output
12
3
4 5
6
1 2
3
7
4
8
5
9
6
Pin No.Cable color
Function Pin No.Cable color
Function
1 Black OUT A 1 Black OUT A
2 White OUT B 2 Red OUT A
3 Orange OUT Z 3 Brown +V
4 Brown +V 4 Blue GND
5 Blue GND 5 White OUT B
6 Shield F.G. 6 Gray OUT B
7 Orange OUT Z
8 Yellow OUT Z
9 Shield F.G.
Totem Pole output NPN open collector output
Rotary encoder circuit Load connection Rotary encoder circuit Load connection
Main
circuit
Load
(※1)Sink current: Max. 30mA
Source current: Max. 10mA(※2)
0V
Output
+V
+
-Load
0V
Output
+V
+
-Sink current: Max. 30mA
Load
Main
circuit
Voltage output Line Driver output
Rotary encoder circuit Load connection Rotary encoder circuit Load connection
Source current: Max.10mA
0V
R
Output
+V
+
-Load
Main
circuit
A phase output
A phase output
0V
+V
+
-
Main
circuit
● Line Driver output
CW
±T
2
T
4
±T
4
T
8
±TT
2
H
LA phase
H
LB phase
H
LZ phase
H
LA phase
H
LB phase
H
LZ phase
T
● Totem Pole output / NPN open collector output / Voltage output
CW
T
±TT
2
±T
2
T
4
±T
4
T
8
H
LA phase
H
LZ phase
H
LB phase
※ CW(Clockwise): In a view of Shaft.
※ The output circuit of A, B, Z phase are the same.(Line Driver output is A, A, B, B, Z, Z phase)※ Totem Pole output can be used for NPN open collector type(※1) or voltage output type(※2).
4+0.05+0.01
10+0.05+0.01
31.8
+0.1
+0.0
533.8
+0.1
+0.0
5
ø30+0.03+0.01
ø32+0.03+0.01
●Shaft inner diameter(Option)
●Shaft inner diameter standard
※Cable length: 250mm
※ " * " indicates the standard specification of diameters.※ 1, 2, 5, 12 P/R are output A, B phase only.(But Line Driver output A, A, B, B phase)
E40S 6 - 5000 - 3 - N - 24 -
3-120̊
3-M3×0.5
DP: 5
P.C.D. 30
P.C.D. 46
3-120̊
3-M3×0.5
DP: 5
P.C.D. 30
P.C.D. 46
※ A, B dimensions are the same as hollow shaft type(E40H).
Series Shaft diameter Pulse / 1Revolution Output
phase Output Power supply Cable
E40S*ø6mmø8mm
*1,*2,*5,10,*12,15,20,23,25,30,35,40,45,50,60,75,100,120,125,150192,200,240,250,256,300,360,400,500,512,
600,800,1000,1024,1200,1500,1800,2000,2048,2500,3000,3600,5000
2: A, B
3: A, B, Z
4: A, A, B, B
6: A, A, B, B,
Z, Z
T: Totem pole output
N: NPN open collector output
V: Voltage output
L: Line Driver output
5: 5VDC±5%24: 12-24VDC
±5%
No mark: Normal type
(※)C:Cableoutgoingconnectortype
E40H E40HB
Inside diameterø6mm*ø8mmø10mmø12mm
E80H*ø30mmø32mm
60,100,360,500512,1024,3200
3: A, B, Z
6: A, A, B, B,
Z, Z ◎Bracket
◎Coupling(E40S Series)
●E40H, E40HB Series ●E80H Series
Type Item A B C D
E40S6 ø6㎜ coupling ø6+0.`1 0 ø15 16.5 22
E40S8 ø8㎜ coupling ø8+0.`1 0 ø19 18.2 25
B A
R19
※
Photoelectric sensors Fiber optic sensors Door sensors Door side sensors Area sensors Proximity sensors Pressure sensors Rotary encoders Connector/Sockets Temperature controllers Temperature/Humidity transducers SSR/Power controllers Counters Timers Panel meters Tachometer/Pulse(Rate) meters Display units Sensor controllers Switching mode power supplies Control switches/Lamps/Buzzers I/O Terminal Blocks & Cables Stepper motors/drivers/motion controllers Graphic/Logic panels Field network devices Laser marking system(Fiber, CO₂, Nd:YAG)
Laser welding/soldering system
http://www.autonics.com
HEAD QUARTERS:18, Bansong-ro 513beon-gil, Haeundae-gu, Busan, Korea
OVERSEAS SALES: #402-404, Bucheon Techno Park, 655, Pyeongcheon-ro, Wonmi-gu, Bucheon, Gyeonggi-do, KoreaTEL: 82-32-610-2730 / FAX: 82-32-329-0728
E-mail: [email protected]
EP-KE-09-0060M