induction machines

81
Induction Motors

Upload: sarthyakpd

Post on 20-Jan-2015

752 views

Category:

Education


3 download

DESCRIPTION

this gives details regarding Induction motor.

TRANSCRIPT

Page 1: Induction machines

Induction Motors

Page 2: Induction machines

Introduction Three-phase induction motors are the most common

and frequently encountered machines in industry- simple design, rugged, low-price, easy maintenance- wide range of power ratings: fractional horsepower to 10

MW - run essentially as constant speed from no-load to full load- Its speed depends on the frequency of the power source

• not easy to have variable speed control

• requires a variable-frequency power-electronic drive for optimal speed control

Page 3: Induction machines

Construction An induction motor has two main parts

- a stationary stator • consisting of a steel frame that supports a hollow, cylindrical core

• core, constructed from stacked laminations (why?), having a number of evenly spaced slots, providing the space for the stator winding

Stator of IM

Page 4: Induction machines

Construction- a revolving rotor

• composed of punched laminations, stacked to create a series of rotor slots, providing space for the rotor winding

• one of two types of rotor windings

• conventional 3-phase windings made of insulated wire (wound-rotor) » similar to the winding on the stator

• aluminum bus bars shorted together at the ends by two aluminum rings, forming a squirrel-cage shaped circuit (squirrel-cage)

Two basic design types depending on the rotor design- squirrel-cage: conducting bars laid into slots and shorted at both ends

by shorting rings.- wound-rotor: complete set of three-phase windings exactly as the

stator. Usually Y-connected, the ends of the three rotor wires are connected to 3 slip rings on the rotor shaft. In this way, the rotor circuit is accessible.

Page 5: Induction machines

Construction

Squirrel cage rotor

Wound rotor

Notice the slip rings

Page 6: Induction machines

Construction

Cutaway in a typical wound-rotor IM. Notice the brushes and the slip rings

Brushes

Slip rings

Page 7: Induction machines

Rotating Magnetic Field Balanced three phase windings, i.e.

mechanically displaced 120 degrees form each other, fed by balanced three phase source

A rotating magnetic field with constant magnitude is produced, rotating with a speed

Where fe is the supply frequency and

P is the no. of poles and nsync is called the synchronous speed in rpm (revolutions per minute)

120 esync

fn rpm

P

120 esync

fn rpm

P

Page 8: Induction machines

Synchronous speed

P 50 Hz 60 Hz

2 3000 3600

4 1500 1800

6 1000 1200

8 750 900

10 600 720

12 500 600

Page 9: Induction machines

Rotating Magnetic Field

Page 10: Induction machines

Rotating Magnetic Field

Page 11: Induction machines

Rotating Magnetic Field( ) ( ) ( ) ( )net a b cB t B t B t B t

sin( ) 0 sin( 120 ) 120 sin( 240) 240M M MB t B t B t

ˆsin( )

3ˆ ˆ[0.5 sin( 120 )] [ sin( 120 )]

2

3ˆ ˆ[0.5 sin( 240 )] [ sin( 240 )]

2

M

M M

M M

B t

B t B t

B t B t

x

x y

x y

Page 12: Induction machines

Rotating Magnetic Field1 3 1 3

ˆ( ) [ sin( ) sin( ) cos( ) sin( ) cos( )]4 4 4 4

3 3 3 3ˆ[ sin( ) cos( ) sin( ) cos( )]

4 4 4 4

net M M M M M

M M M M

B t B t B t B t B t B t

B t B t B t B t

x

y

ˆ ˆ[1.5 sin( )] [1.5 cos( )]M MB t B t x y

Page 13: Induction machines

Rotating Magnetic Field

Page 14: Induction machines

Principle of operation This rotating magnetic field cuts the rotor windings and

produces an induced voltage in the rotor windings Due to the fact that the rotor windings are short circuited, for

both squirrel cage and wound-rotor, and induced current flows in the rotor windings

The rotor current produces another magnetic field A torque is produced as a result of the interaction of those two

magnetic fields

Where ind is the induced torque and BR and BS are the magnetic flux densities of the rotor and the stator respectively

ind R skB B

Page 15: Induction machines

Induction motor speed At what speed will the IM run?

- Can the IM run at the synchronous speed, why?- If rotor runs at the synchronous speed, which is the

same speed of the rotating magnetic field, then the rotor will appear stationary to the rotating magnetic field and the rotating magnetic field will not cut the rotor. So, no induced current will flow in the rotor and no rotor magnetic flux will be produced so no torque is generated and the rotor speed will fall below the synchronous speed

- When the speed falls, the rotating magnetic field will cut the rotor windings and a torque is produced

Page 16: Induction machines

Induction motor speed So, the IM will always run at a speed lower than

the synchronous speed The difference between the motor speed and the

synchronous speed is called the Slip

Where nslip= slip speed

nsync= speed of the magnetic field

nm = mechanical shaft speed of the motor

slip sync mn n n slip sync mn n n

Page 17: Induction machines

The Slip

sync m

sync

n ns

n

sync m

sync

n ns

n

Where s is the slip

Notice that : if the rotor runs at synchronous speed

s = 0

if the rotor is stationary

s = 1

Slip may be expressed as a percentage by multiplying the above eq. by 100, notice that the slip is a ratio and doesn’t have units

Page 18: Induction machines

Induction Motors and Transformers Both IM and transformer works on the principle of

induced voltage- Transformer: voltage applied to the primary windings

produce an induced voltage in the secondary windings- Induction motor: voltage applied to the stator windings

produce an induced voltage in the rotor windings- The difference is that, in the case of the induction

motor, the secondary windings can move- Due to the rotation of the rotor (the secondary winding

of the IM), the induced voltage in it does not have the same frequency of the stator (the primary) voltage

Page 19: Induction machines

Frequency The frequency of the voltage induced in the rotor is

given by

Where fr = the rotor frequency (Hz)

P = number of stator poles

n = slip speed (rpm)

120r

P nf

( )

120

120

s mr

se

P n nf

P snsf

Page 20: Induction machines

Frequency What would be the frequency of the rotor’s induced

voltage at any speed nm?

When the rotor is blocked (s=1) , the frequency of the induced voltage is equal to the supply frequency

On the other hand, if the rotor runs at synchronous speed (s = 0), the frequency will be zero

r ef s fr ef s f

Page 21: Induction machines

Torque While the input to the induction motor is electrical

power, its output is mechanical power and for that we should know some terms and quantities related to mechanical power

Any mechanical load applied to the motor shaft will introduce a Torque on the motor shaft. This torque is related to the motor output power and the rotor speed

and .outload

m

PN m

.out

loadm

PN m

2

/60

mm

nrad s

2

/60

mm

nrad s

Page 22: Induction machines

Horse power Another unit used to measure mechanical power is

the horse power It is used to refer to the mechanical output power

of the motor Since we, as an electrical engineers, deal with

watts as a unit to measure electrical power, there is a relation between horse power and watts

746hp watts746hp watts

Page 23: Induction machines

ExampleA 208-V, 10hp, four pole, 60 Hz, Y-connected

induction motor has a full-load slip of 5 percent1. What is the synchronous speed of this motor?

2. What is the rotor speed of this motor at rated load?

3. What is the rotor frequency of this motor at rated load?

4. What is the shaft torque of this motor at rated load?

Page 24: Induction machines

Solution

1.

2.

3.

4.

120 120(60)1800

4e

sync

fn rpm

P

(1 )

(1 0.05) 1800 1710m sn s n

rpm

0.05 60 3r ef sf Hz

260

10 746 /41.7 .

1710 2 (1/ 60)

out outload

mm

P Pn

hp watt hpN m

Page 25: Induction machines

Equivalent Circuit The induction motor is similar to the transformer with the

exception that its secondary windings are free to rotate

As we noticed in the transformer, it is easier if we can combine these two circuits in one circuit but there are some difficulties

Page 26: Induction machines

Equivalent Circuit When the rotor is locked (or blocked), i.e. s =1, the

largest voltage and rotor frequency are induced in the rotor, Why?

On the other side, if the rotor rotates at synchronous speed, i.e. s = 0, the induced voltage and frequency in the rotor will be equal to zero, Why?

Where ER0 is the largest value of the rotor’s induced voltage obtained at s = 1(loacked rotor)

0R RE sE 0R RE sE

Page 27: Induction machines

Equivalent Circuit The same is true for the frequency, i.e.

It is known that

So, as the frequency of the induced voltage in the rotor changes, the reactance of the rotor circuit also changes

Where Xr0 is the rotor reactance

at the supply frequency

(at blocked rotor)

r ef s fr ef s f

2X L f L 2X L f L

0

2

2r r r r r

e r

r

X L f L

sf L

sX

0

2

2r r r r r

e r

r

X L f L

sf L

sX

Page 28: Induction machines

Equivalent Circuit Then, we can draw the rotor equivalent circuit as

follows

Where ER is the induced voltage in the rotor and RR is the rotor resistance

Page 29: Induction machines

Equivalent Circuit Now we can calculate the rotor current as

Dividing both the numerator and denominator by s so nothing changes we get

Where ER0 is the induced voltage and XR0 is the rotor reactance at blocked rotor condition (s = 1)

0

0

( )

( )

RR

R R

R

R R

EI

R jX

sE

R jsX

0

0( )

RR

RR

EI

RjX

s

0

0( )

RR

RR

EI

RjX

s

Page 30: Induction machines

Equivalent Circuit Now we can have the rotor equivalent circuit

Page 31: Induction machines

Equivalent Circuit Now as we managed to solve the induced voltage

and different frequency problems, we can combine the stator and rotor circuits in one equivalent circuitWhere

22 0

22

2

1 0

eff R

eff R

R

eff

eff R

Seff

R

X a X

R a R

II

a

E a E

Na

N

Page 32: Induction machines

Power losses in Induction machines Copper losses

- Copper loss in the stator (PSCL) = I12R1

- Copper loss in the rotor (PRCL) = I22R2

Core loss (Pcore) Mechanical power loss due to friction and windage How this power flow in the motor?

Page 33: Induction machines

Power flow in induction motor

Page 34: Induction machines

Power relations

3 cos 3 cosin L L ph phP V I V I 2

1 13SCLP I R

( )AG in SCL coreP P P P

22 23RCLP I R

conv AG RCLP P P

( )out conv f w strayP P P P convind

m

P

Page 35: Induction machines

Equivalent Circuit We can rearrange the equivalent circuit as follows

Actual rotor resistance

Resistance equivalent to

mechanical load

Page 36: Induction machines

Power relations

3 cos 3 cosin L L ph phP V I V I 2

1 13SCLP I R

( )AG in SCL coreP P P P

22 23RCLP I R

conv AG RCLP P P

( )out conv f w strayP P P P

conv RCLP P 2 223

RI

s

2 22

(1 )3

R sI

s

RCLP

s

(1 )RCLP s

s

(1 )conv AGP s P conv

indm

P

(1 )

(1 )AG

s

s P

s

Page 37: Induction machines

Power relations

AGP

RCLP

convP

1

s

1-s

: :

1 : : 1-AG RCL convP P P

s s

: :

1 : : 1-AG RCL convP P P

s s

Page 38: Induction machines

ExampleA 480-V, 60 Hz, 50-hp, three phase induction motor is

drawing 60A at 0.85 PF lagging. The stator copper losses are 2 kW, and the rotor copper losses are 700 W. The friction and windage losses are 600 W, the core losses are 1800 W, and the stray losses are negligible. Find the following quantities:

1. The air-gap power PAG.

2. The power converted Pconv.

3. The output power Pout.

4. The efficiency of the motor.

Page 39: Induction machines

Solution1.

2.

3.

3 cos

3 480 60 0.85 42.4 kW

in L LP V I

42.4 2 1.8 38.6 kWAG in SCL coreP P P P

70038.6 37.9 kW

1000

conv AG RCLP P P

&

60037.9 37.3 kW

1000

out conv F WP P P

Page 40: Induction machines

Solution

4.

37.350 hp

0.746outP

100%

37.3100 88%

42.4

out

in

P

P

Page 41: Induction machines

ExampleA 460-V, 25-hp, 60 Hz, four-pole, Y-connected induction motor

has the following impedances in ohms per phase referred to the stator circuit:

R1= 0.641 R2= 0.332

X1= 1.106 X2= 0.464 XM= 26.3

The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2 percent at the rated voltage and rated frequency, find the motor’s

1. Speed

2. Stator current

3. Power factor

4. Pconv and Pout

5. ind and load

6. Efficiency

Page 42: Induction machines

Solution

1.

2.

120 120 601800 rpm

4e

sync

fn

P

(1 ) (1 0.022) 1800 1760 rpmm syncn s n

22 2

0.3320.464

0.02215.09 0.464 15.1 1.76

RZ jX j

sj

2

1 1

1/ 1/ 0.038 0.0662 1.76

112.94 31.1

0.0773 31.1

fM

ZjX Z j

Page 43: Induction machines

Solution

3.

4.

0.641 1.106 12.94 31.1

11.72 7.79 14.07 33.6

tot stat fZ Z Z

j

j

1

460 0

3 18.88 33.6 A14.07 33.6tot

VI

Z

cos33.6 0.833 laggingPF 3 cos 3 460 18.88 0.833 12530 Win L LP V I

2 21 13 3(18.88) 0.641 685 WSCLP I R

12530 685 11845 WAG in SCLP P P

Page 44: Induction machines

Solution

5.

6.

(1 ) (1 0.022)(11845) 11585 Wconv AGP s P

& 11585 1100 10485 W

10485= 14.1 hp

746

out conv F WP P P

1184562.8 N.m

18002 60

AGind

sync

P

1048556.9 N.m

17602 60

outload

m

P

10485100% 100 83.7%

12530out

in

P

P

Page 45: Induction machines

Torque, power and Thevenin’s Theorem Thevenin’s theorem can be used to transform the

network to the left of points ‘a’ and ‘b’ into an equivalent voltage source VTH in series with equivalent impedance RTH+jXTH

Page 46: Induction machines

Torque, power and Thevenin’s Theorem

1 1( )M

THM

jXV V

R j X X

1 1( ) //TH TH MR jX R jX jX

2 21 1

| | | |( )

MTH

M

XV V

R X X

Page 47: Induction machines

Torque, power and Thevenin’s Theorem Since XM>>X1 and XM>>R1

Because XM>>X1 and XM+X1>>R1

1

MTH

M

XV V

X X1

MTH

M

XV V

X X

2

11

1

MTH

M

TH

XR R

X X

X X

2

11

1

MTH

M

TH

XR R

X X

X X

Page 48: Induction machines

Torque, power and Thevenin’s Theorem

Then the power converted to mechanical (Pconv)

2 222

2( )

TH TH

T

TH TH

V VI

Z RR X X

s

2 22

(1 )3conv

R sP I

s

And the internal mechanical torque (Tconv)

convind

m

P

(1 )

conv

s

P

s

2 223

AG

s s

RI Ps

Page 49: Induction machines

Torque, power and Thevenin’s Theorem

2

2

222

2

3

( )

THind

s

TH TH

V R

sRR X X

s

2 2

222

2

31

( )

TH

inds

TH TH

RV

s

RR X X

s

2 2

222

2

31

( )

TH

inds

TH TH

RV

s

RR X X

s

Page 50: Induction machines

Torque-speed characteristics

Typical torque-speed characteristics of induction motor

Page 51: Induction machines

Comments1. The induced torque is zero at synchronous speed.

Discussed earlier.

2. The curve is nearly linear between no-load and full load. In this range, the rotor resistance is much greater than the reactance, so the rotor current, torque increase linearly with the slip.

3. There is a maximum possible torque that can’t be exceeded. This torque is called pullout torque and is 2 to 3 times the rated full-load torque.

Page 52: Induction machines

Comments4. The starting torque of the motor is slightly higher

than its full-load torque, so the motor will start carrying any load it can supply at full load.

5. The torque of the motor for a given slip varies as the square of the applied voltage.

6. If the rotor is driven faster than synchronous speed it will run as a generator, converting mechanical power to electric power.

Page 53: Induction machines

Complete Speed-torque c/c

Page 54: Induction machines

Maximum torque Maximum torque occurs when the power

transferred to R2/s is maximum.

This condition occurs when R2/s equals the magnitude of the impedance RTH + j (XTH + X2)

max

2 222( )TH TH

T

RR X X

s

max

2

2 22( )

T

TH TH

Rs

R X X

max

2

2 22( )

T

TH TH

Rs

R X X

Page 55: Induction machines

Maximum torque The corresponding maximum torque of an induction

motor equals

The slip at maximum torque is directly proportional to the rotor resistance R2

The maximum torque is independent of R2

2

max 2 22

31

2 ( )TH

s TH TH TH

V

R R X X

2

max 2 22

31

2 ( )TH

s TH TH TH

V

R R X X

Page 56: Induction machines

Maximum torque Rotor resistance can be increased by inserting

external resistance in the rotor of a wound-rotor induction motor.

The

value of the maximum torque remains unaffected

but

the speed at which it occurs can be controlled.

Page 57: Induction machines

Maximum torque

Effect of rotor resistance on torque-speed characteristic

Page 58: Induction machines

ExampleA two-pole, 50-Hz induction motor supplies 15kW to a

load at a speed of 2950 rpm.

1. What is the motor’s slip?

2. What is the induced torque in the motor in N.m under these conditions?

3. What will be the operating speed of the motor if its torque is doubled?

4. How much power will be supplied by the motor when the torque is doubled?

Page 59: Induction machines

Solution

1.

2.

120 120 503000 rpm

2

3000 29500.0167 or 1.67%

3000

esync

sync m

sync

fn

Pn n

sn

3

no given

assume and

15 1048.6 N.m

22950

60

f W

conv load ind load

convind

m

P

P P

P

Page 60: Induction machines

Solution3. In the low-slip region, the torque-speed curve is linear

and the induced torque is direct proportional to slip. So, if the torque is doubled the new slip will be 3.33% and the motor speed will be

4.

(1 ) (1 0.0333) 3000 2900 rpmm syncn s n

2(2 48.6) (2900 ) 29.5 kW

60

conv ind mP

Page 61: Induction machines

ExampleA 460-V, 25-hp, 60-Hz, four-pole, Y-connected wound-rotor

induction motor has the following impedances in ohms per phase referred to the stator circuit

R1= 0.641 R2= 0.332

X1= 1.106 X2= 0.464 XM= 26.3

1. What is the maximum torque of this motor? At what speed and slip does it occur?

2. What is the starting torque of this motor?

3. If the rotor resistance is doubled, what is the speed at which the maximum torque now occur? What is the new starting torque of the motor?

4. Calculate and plot the T-s c/c for both cases.

Page 62: Induction machines

Solution

2 2

1 1

2 2

( )

46026.3

3 255.2 V(0.641) (1.106 26.3)

MTH

M

XV V

R X X

2

11

226.3

(0.641) 0.5901.106 26.3

MTH

M

XR R

X X

1 1.106THX X

Page 63: Induction machines

Solution

1.

The corresponding speed is

max

2

2 22

2 2

( )

0.3320.198

(0.590) (1.106 0.464)

T

TH TH

Rs

R X X

(1 ) (1 0.198) 1800 1444 rpmm syncn s n

Page 64: Induction machines

SolutionThe torque at this speed is

2

max 2 22

2

2 2

31

2 ( )

3 (255.2)2

2 (1800 )[0.590 (0.590) (1.106 0.464) ]60

229 N.m

TH

s TH TH TH

V

R R X X

Page 65: Induction machines

Solution2. The starting torque can be found from the torque eqn.

by substituting s = 1

2 2

2122

2

1

22

2 22 2

2

2 2

31

( )

3

[ ( ) ]

3 (255.2) (0.332)2

1800 [(0.590 0.332) (1.106 0.464) ]60

104 N.m

TH

start ind ss

TH TH

s

TH

s TH TH

RV

s

RR X X

s

V R

R R X X

Page 66: Induction machines

Solution3. If the rotor resistance is doubled, then the slip at

maximum torque doubles too

The corresponding speed is

The maximum torque is still

max = 229 N.m

max

2

2 22

0.396( )

T

TH TH

Rs

R X X

(1 ) (1 0.396) 1800 1087 rpmm syncn s n

Page 67: Induction machines

SolutionThe starting torque is now

2

2 2

3 (255.2) (0.664)2

1800 [(0.590 0.664) (1.106 0.464) ]60

170 N.m

start

Page 68: Induction machines

Determination of motor parameters Due to the similarity between the induction motor

equivalent circuit and the transformer equivalent circuit, same tests are used to determine the values of the motor parameters.- DC test: determine the stator resistance R1

- No-load test: determine the rotational losses and magnetization current (similar to no-load test in Transformers).

- Locked-rotor test: determine the rotor and stator impedances (similar to short-circuit test in Transformers).

Page 69: Induction machines

DC test- The purpose of the DC test is to determine R1. A variable

DC voltage source is connected between two stator terminals.

- The DC source is adjusted to provide approximately rated stator current, and the resistance between the two stator leads is determined from the voltmeter and ammeter readings.

Page 70: Induction machines

DC test- then

- If the stator is Y-connected, the per phase stator resistance is

- If the stator is delta-connected, the per phase stator resistance is

DCDC

DC

VR

I

1 2DCR

R 1 2DCR

R

1

3

2 DCR R1

3

2 DCR R

Page 71: Induction machines

No-load test

1. The motor is allowed to spin freely

2. The only load on the motor is the friction and windage losses, so all Pconv is consumed by mechanical losses

3. The slip is very small

Page 72: Induction machines

No-load test

4. At this small slip

The equivalent circuit reduces to…

2 22 2

(1 ) R (1 ) &

R s sR X

s s

Page 73: Induction machines

No-load test

5. Combining Rc & RF+W we get……

Page 74: Induction machines

No-load test6. At the no-load conditions, the input power measured by

meters must equal the losses in the motor.

7. The PRCL is negligible because I2 is extremely small because R2(1-s)/s is very large.

8. The input power equals

Where

&

21 13

in SCL core F W

rot

P P P P

I R P

&

21 13

in SCL core F W

rot

P P P P

I R P

&rot core F WP P P

Page 75: Induction machines

No-load test9. The equivalent input impedance is thus approximately

If X1 can be found, in some other fashion, the magnetizing impedance XM will be known

11,

eq Mnl

VZ X X

I 1

1,eq M

nl

VZ X X

I

Page 76: Induction machines

Blocked-rotor test In this test, the rotor is locked or blocked so that it

cannot move, a voltage is applied to the motor, and the resulting voltage, current and power are measured.

Page 77: Induction machines

Blocked-rotor test The AC voltage applied to the stator is adjusted so

that the current flow is approximately full-load value.

The locked-rotor power factor can be found as

The magnitude of the total impedance

cos3

in

l l

PPF

V I cos

3in

l l

PPF

V I

LR

VZ

ILR

VZ

I

Page 78: Induction machines

Blocked-rotor test

Where X’1 and X’2 are the stator and rotor reactances at the test frequency respectively

'

cos sin

LR LR LR

LR LR

Z R jX

Z j Z

1 2

' ' '1 2

LR

LR

R R R

X X X

2 1LRR R R

'1 2

ratedLR LR

test

fX X X X

f

Page 79: Induction machines

Blocked-rotor test

X1 and X2 as function of XLR

Rotor Design X1 X2

Wound rotor 0.5 XLR 0.5 XLR

Design A 0.5 XLR 0.5 XLR

Design B 0.4 XLR 0.6 XLR

Design C 0.3 XLR 0.7 XLR

Design D 0.5 XLR 0.5 XLR

Page 80: Induction machines

Midterm Exam No.2

Page 81: Induction machines

ExampleThe following test data were taken on a 7.5-hp, four-pole, 208-V, 60-Hz, design A, Y-connected IM having a rated current of 28 A.

DC Test:

VDC = 13.6 V IDC = 28.0 A

No-load Test:

Vl = 208 V f = 60 Hz

I = 8.17 A Pin = 420 W

Locked-rotor Test:

Vl = 25 V f = 15 Hz

I = 27.9 A Pin = 920 W

(a) Sketch the per-phase equivalent circuit of this motor.

(b) Find the slip at pull-out torque, and find the value of the pull-out torque.