install shower

7/26/2019 Install Shower

1/5

InstallationInstructions

Certified to comply with ANSI A112.18.1

Recommended Tools & Materials

ROUGHING-IN DIMENSIONS

Thank you for selecting American-Standard...the benchmarkof fine quality for over 100 years.

To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.

M965118 REV. 1.2 (2/15

1662.2131662.223

Electric Drill

Torch

6mm (15/64")Drill Bit

PencilPhillips Screwdriver

OPTIONAL TOFINISHED FLOOR

USUALLY BETWEEN36" 48"TO

Hammer

COMMERCIAL SHOWERSYSTEM KITS: 1.5gpm & 2.5gpm 1662.223

1662.213

BOTTOMOF SHOWER

74" FOR HEADCLEARANCE

1-5/8" TO 3-1/4"

48" TO 54"OPTIONAL

12"OPTIONAL

OPTIONAL

12"OPTIONAL

OPTIONAL TO FINISHEDFLOOR USUALLY

BETWEEN 65" TO 78"

1/2" NPT

1/2" NPT

1/2" SUPPLIES

PLUG TUBOUTLET

6" DIA.

5-1/2" REF.

7" REF.

FINISHED WALLFLOWISE

SHOWER HEAD

8"

VALVE BODY HAS 1/2"SWEAT INLETS AND OUTLETS

5-3/4"

33-3/8"

1-1/4"

1/2"1/2"NPT

4"REF.

Adjustable Wrench

10'

Pipe Wrench Tubing Cutter

TapeMeasure

Sealing Tape

Installation must conform to all local building codes.

2-3/4" DIA.1660766.002(1.5 gpm)

1660767.002(2.5 gpm)

3-5/16"8-1/8"

1/2" NPSM


2/5

M965118 REV. 1.2 (2/15

INSTALL THE R120SS VALVE BODY1

INSTALL THE R420 TWO-WAY DIVERTER2

When finished tiling the wall, remove PLASTER GUARD.

Remove plug from shower pipe.

R120SS

TWO-WAYDIVERTER

When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS(IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops(if present) and plaster guard to continue installation. Use thread sealant or Teflon tapeon threaded connections.

NOTE

IMPORTANT

See Roughing-in diagram before starting.

Connections are: 1/2" copper sweat for sweat inlets

1/2" copper sweat for sweat tub and shower outlets

REFER TO INSTALLATION INSTRUCTIONS (M968387) SUPPLIED WITH VALVE BODY FORCOMPLETE INSTALLATION AND REPAIR PART INFORMATION.

REFER TO INSTALLATION INSTRUCTIONS (50321) SUPPLIED WITH DIVERTER FORCOMPLETE INSTALLATION AND REPAIR PART INFORMATION.

REFER TO INSTALLATION INSTRUCTIONS (M968763) SUPPLIED WITH VALVE

TRIM KIT FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION.

The reverse side of the body is marked with arrows.CAUTION: Do not solder near the VALVE. Damage to the SEAL may occur. Do not sealany outlets. The DIVERTER cannot be used as a stop valve. Use thread sealant or sealingtape on threaded connections.

NOTE

IMPORTANT

NOTE

1/2" SWEAT PLUG

1/2" NPT INLET

1/2" NPTSHOWER

1/2" NPT HANDSHOWER

MAKE ALL CONCEALED PIPING CONNECTIONS

INSTALL VALVE TRIM

3

4

See Roughing-in diagram before starting. The port with the BATH TUB picture is the high flow.

The DIVERTER can be installed with the inlet rotated in any position.

All connections are 1/2" NPT.

For proper positioning the finished wall must be within the side of PLASTER GUARD.

Connect the R420 TWO-WAY DIVERTER to the R120SS VALVE BODY.

See Roughing-in diagram before starting.

Make Hot and Cold supply connections to the VALVE BODY. Inlet and outlet connections to the valve body are 1/2" copper sweat.

Make SHOWER connection from DIVERTER. (Use the port with the BATH TUB picture). DIVERTER IS 1/2" NPT.

Make the connection to the HAND SHOWER. The HAND SHOWER connections are 1/2" NPT.

For support, use PIPE BRACES secured to wooden braces. Cap off SHOWER and HAND SHOWER.With the R120SS VALVE turned off, turn on water supplies. Check for leaks.

Finish all wall construction.

PLASTER GUARD

PLUG

FLOWISESHOWER HEAD


3/5

M965118 REV. 1.2 (2/15)

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT:DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTHWITH A COARSE SURFACE.

INSTALL WALL SUPPLY

1/2" NPTAPPLY SEALANT

OR SEALING TAPESupply to WALL SUPPLY is 1/2" NPT. See rough-in above for detailed information.

Apply sealant or sealing tape to threads of 1/2" NPT supply nipple.

REFER TO INSTALLATION INSTRUCTIONS (M968637) SUPPLIED WITH WALLSUPPLY FOR COMPLETE INSTALLATION AND REPAIR PART INFORMATION.

REFER TO INSTALLATION INSTRUCTIONS (M968637)SUPPLIED WITH SHOWER SYSTEM KIT FOR COMPLETEINSTALLATION AND REPAIR PART INFORMATION.

REFER TO INSTALLATION INSTRUCTIONS (M968637)SUPPLIED WITH SHOWER SYSTEM KIT FOR COMPLETEINSTALLATION AND REPAIR PART INFORMATION.

NOTE

NOTE

INSTALL HAND SHOWER SLIDE BAR7

6

The height and location of the SLIDE BAR is optional.It can be installed to the right or left side of theR120SS VALVE.

NOTE

INSTALL HOSE AND HAND SHOWERTEST SHOWER SYSTEM8

Place the HAND SHOWER into the SLIDE BAR after allhose connections are made. The installation of theSHOWER SYSTEM KIT is now complete.

Turn on water supplies and check all fuctions of of theSHOWER SYSTEM KIT. Check for any leaks.

35-3/8"

33-3/8"

2-1/2"

3-3/8"

INSTALL DIVERTER TRIM AND HANDLE5

PLASTER GUARD

X

When finished tiling the wall, remove PLASTER GUARD.

Place ESCUTCHEON (1)onto ESCUTCHEON HOLDER (2).

Thread ESCUTCHEON HOLDER (2)onto DIVERTER VALVE (3).Tighten until ESCUTCHEON (1) is snug against finished wall.

Install HANDLE SKIRT (4)onto VALVE STEM (5).

Push DECORATIVE RING (6)onto LEVER HANDLE (7).

Align LEVER HANDLE (7)and push ontoHANDLE SKIRT (4). Install HANDLESCREW (8)and tighten.

Push INDEX CAP (9)into LEVERHANDLE (7).

1

5

6

7

89

2

4

3

HAND SHOWER


4/5

M965118 REV. 1.2 (2/15)

MODEL NUMBER

T675.501

MODEL NUMBER

R120SS

M952100-0070APRESSURE BALANCING UNI

023529-0070ACARTRIDG

023603-0070ACARTRIDGE SCREWS

051122-0070ASCREWDRIVER STOPS

050145-0070A1/2" SWEAT PLUG

PRESSURE BALANCETEMPERATURE/VOLUME

CONTROL VALVE

COLONY SOFTSHOWER TRIM

MODEL NUMBER

R420

2-WAY DIVERTERVALVE

M961854-0070AFIXATION RING WITH SCREWS

PLASTERGUARD

X

TWO WAYBODY

060220-0070ADIVERTER REPAIR KIT

060219-0070ASTEM KIT

051310-0070A

SPRING KIT

051309-0070ACAP

912647-0070ACAP SEAL

912737-0070ASTEM O-RING

023560-0020ASHOWER ARMAND FLANGE

M953530-0020A

SHOWER HEAD

M961856-0020AESCUTCHEON AND SCREWS

078016-0020AESCUTCHEON SCREWS

M909606-0020ADECAL

M907050-0020AESCUTCHEON CAP SET

M961636-0020ALEVER HANDLE KIT

030126-0070AHANDLE SCREW KIT

1660.710-002FloWise

SHOWER HEAD

954027-002OAESCUTCHEON HOLDER

012157-0020AHANDLE SKIRT

012673-0020ALEVER HANDLE

012205-0070ACOLOR RING KIT

012189-0020AINDEX BUTTON

For toll-free information and answers to your questions, call:1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. ESTIN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. ESTIN MEXICO 01-800-839-1200

P r oduc t n ames l i s t e d h e r e i n a r e t r ademar ks o f Amer i can S t an da r d I n c .

AS Amer i ca , I n c . 2011

HOT LINE FOR HELP

918572-0070AHANDLE SCREW

012288-0020A

ESCUTCHEON KIT

MODEL NUMBER

T342.430

HERITAGE HANDLEDIVERTER TRIM

013205-0070A

STOP VALVE O-RING


5/5

M965118 REV. 1.2 (2/15

8888.037.002

WALL SUPPLY

8888.035.002

METAL HOSE

1660.236.002

36" SLIDE BAR

M962506-0020ASUPPORT BRACKET

M962507-0020AHAND SHOWER HOLDER

M919211-0020A36"SLIDE BAR

M962506-0020ASUPPORT BRACKET

M950105-0070AHARDWARE KIT

8888037.002WALL SUPPLY

030782-0020AHOSE KIT

M962520-0020ACHECK VALVE

For toll-free information and answers to your questions, call:1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. ESTIN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. ESTIN MEXICO 01-800-839-1200

P r oduc t n ames l i s t e d h e r e i n a r e t r ademar ks o f Amer i can S t an da r d I n c .

AS Amer i ca , I n c . 2011

HOT LINE FOR HELP

3-FUNCTION HANDSHOWER

1660766.002(1.5 gpm)

1660767.002(2.5 gpm)

install shower

Documents