install guideimages.idatalink.com/corporate/content/manuals/rsa-ha6p/...08 white/purpleblack dot 09...
TRANSCRIPT
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2014-2015 ACURA RLX PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T001_H
AB
T-HARNESS / COMPONENT LOCATOR - 1 OF 1 PAGE 2 OF 8
U.S. Patent No. 8,856,780 2014-2015 Acura RLX PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) RED - 01
PARKING LIGHTS (-) PINK - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: BLUE
1
2
1
VS2VS2
VS1VS1
VS4VS4
VS3VS3
M5
M4
MS2
MS1
T001_H
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
1: 28 PIN PTS CONNECTOR LT BROWN
2: 24 PIN IGNITION CONNECTOR GRAY
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION HARNESS
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
01010202030304040505060607070808090910101111121213131414151516161717181819192020
010102020303040405050606
RELAY
!
M3
M2M5
M4
PAGE 3 OF 8
U.S. Patent No. 8,856,780 2014-2015 Acura RLX PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
T001_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
AB
PAGE 4 OF 8
U.S. Patent No. 8,856,780 2014-2015 Acura RLX PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) RED - 01
PARKING LIGHTS (-) PINK - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: BLUE
1
2
1
1122334455667788991011111212
131314141515161617171818191920202121222223232424
1011
182324
11223344556677889910101111131314 1212
25252626272728 15161617171818191920202121
6714 12
28 1521222223232424
T001_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
12V (+) PINK - 14
CANH (DATA) RED - 06
IGNITION 2 (+) YELLOW - 28
GROUND (-) BROWN - 15
S-NET (DATA) RED - 21
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) GRAY - 12
CANL (DATA) WHITE - 07
START (+) BLUE -18
IGNITION 1 (+) DKBLUE - 11
ACCESSORY (+) ORANGE - 24
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE
03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE04 WHITE/RED•BLUE DOT04 WHITE/RED•BLUE DOT05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: LT BROWN
2: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
!
M3
M2M5
M4
PAGE 5 OF 8
U.S. Patent No. 8,856,780 2014-2015 Acura RLX PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
U.S. Patent No. 8,856,780 2014-2015 Acura RLX PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
U.S. Patent No. 8,856,780 2014-2015 Acura RLX PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
U.S. Patent No. 8,856,780 2014-2015 Acura RLX PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2013-2015 HONDA ACCORD CROSSTOUR PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T003_H
AB
T-HARNESS / COMPONENT LOCATOR - 1 OF 1 PAGE 2 OF 8
U.S. Patent No. 8,856,780 2013-2015 Honda Accord Crosstour PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) RED - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
2
1
VS2VS2
VS1VS1
VS4VS4
VS3VS3
RELAYM5
M4
MS2
MS1
T003_H
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
1: 28 PIN PTS CONNECTOR GRAY
2: 24 PIN IGNITION CONNECTOR GRAY
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION HARNESS
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
01010202030304040505060607070808090910101111121213131414151516161717181819192020
010102020303040405050606
!
M3
M2M5
M4
PAGE 3 OF 8
U.S. Patent No. 8,856,780 2013-2015 Honda Accord Crosstour PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
T003_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
AB
PAGE 4 OF 8
U.S. Patent No. 8,856,780 2013-2015 Honda Accord Crosstour PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) RED - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
2
1
1122334455667788991011111212
131314141515161617171818191920202121222223232424
1011
182324
11223344556677889910101111131314 1212
25252626272728 15161617171818191920202121
6714 12
28 1521222223232424
T003_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
12V (+) WHITE - 14
CANH (DATA) PINK - 06
IGNITION 2 (+) YELLOW - 28
GROUND (-) BROWN - 15
S-NET (DATA) LTGREEN - 21
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) BLUE - 12
CANL (DATA) BLUE - 07
START (+) LTGREEN -18
IGNITION 1 (+) WHITE - 11
ACCESSORY (+) GRAY - 24
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE
03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE04 WHITE/RED•BLUE DOT04 WHITE/RED•BLUE DOT05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: GRAY
2: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
!
M3
M2M5
M4
PAGE 5 OF 8
U.S. Patent No. 8,856,780 2013-2015 Honda Accord Crosstour PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
U.S. Patent No. 8,856,780 2013-2015 Honda Accord Crosstour PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
U.S. Patent No. 8,856,780 2013-2015 Honda Accord Crosstour PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
U.S. Patent No. 8,856,780 2013-2015 Honda Accord Crosstour PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2013-2017 HONDA ACCORD HYBRID PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T002_H
AB
T-HARNESS / COMPONENT LOCATOR - 1 OF 1 PAGE 2 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) PINK - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
2
1
VS2VS2
VS1VS1
VS4VS4
VS3VS3
M5
M4
MS2
MS1
T002_H
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
1: 28 PIN PTS CONNECTOR LT BROWN
2: 24 PIN IGNITION CONNECTOR GRAY
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION HARNESS
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
01010202030304040505060607070808090910101111121213131414151516161717181819192020
010102020303040405050606
RELAY
!
M3
M2M5
M4
PAGE 3 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
T002_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
AB
PAGE 4 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) PINK - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
2
1
1122334455667788991011111212
131314141515161617171818191920202121222223232424
1011
182324
11223344556677889910101111131314 1212
25252626272728 15161617171818191920202121
6714 12
28 1521222223232424
T002_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
12V (+) WHITE - 14
CANH (DATA) PINK - 06
IGNITION 2 (+) YELLOW - 28
GROUND (-) BROWN - 15
S-NET (DATA) GRAY - 21
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) BLUE - 12
CANL (DATA) BLUE - 07
START (+) BLUE -18
IGNITION 1 (+) WHITE - 11
ACCESSORY (+) GRAY - 24
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE
03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE04 WHITE/RED•BLUE DOT04 WHITE/RED•BLUE DOT05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: LT BROWN
2: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
!
M3
M2M5
M4
PAGE 5 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2013-2017 HONDA ACCORD PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T002_H
AB
T-HARNESS / COMPONENT LOCATOR - 1 OF 1 PAGE 2 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) PINK - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
2
1
VS2VS2
VS1VS1
VS4VS4
VS3VS3
M5
M4
MS2
MS1
T002_H
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
1: 28 PIN PTS CONNECTOR LT BROWN
2: 24 PIN IGNITION CONNECTOR GRAY
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION HARNESS
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
01010202030304040505060607070808090910101111121213131414151516161717181819192020
010102020303040405050606
RELAY
!
M3
M2M5
M4
PAGE 3 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
T002_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
AB
PAGE 4 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) PINK - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
2
1
1122334455667788991011111212
131314141515161617171818191920202121222223232424
1011
182324
11223344556677889910101111131314 1212
25252626272728 15161617171818191920202121
6714 12
28 1521222223232424
T002_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
12V (+) WHITE - 14
CANH (DATA) PINK - 06
IGNITION 2 (+) YELLOW - 28
GROUND (-) BROWN - 15
S-NET (DATA) GRAY - 21
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) BLUE - 12
CANL (DATA) BLUE - 07
START (+) BLUE -18
IGNITION 1 (+) WHITE - 11
ACCESSORY (+) GRAY - 24
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE
03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE04 WHITE/RED•BLUE DOT04 WHITE/RED•BLUE DOT05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: LT BROWN
2: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
!
M3
M2M5
M4
PAGE 5 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
U.S. Patent No. 8,856,780 2013-2017 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2018 HONDA ACCORD PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T010_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
PAGE 2 OF 6
U.S. Patent No. 8,856,780 2018 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
2: BLUE
1
2
1
T010_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY BCM, ABOVE DASH FUSEBOX (A)
12V (+) RED - 01
CANH (DATA) PINK - 54
GROUND (-) BLACK - 56
S-NET (DATA) TAN - 54
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) WHITE - 63
CANL (DATA) BLUE -55
STARTER (+) PURPLE - 51
IGNITION 2 (+) GRAY - 43
IGNITION 1 (+) WHITE - 54
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT01 GRAY/BLACK•BLUE DOT
03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: WHITE
3: BROWN
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT:
1- NO TAKEOVER AVAILABLE. ENGINE WILL SHUTDOWN UPON UNLOCK.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
PARKING LIGHTS (-) GRAY - 12
LIGHTS OFF (-) YELLOW - 41 11818
3434
5050
6666
1717
3333
4949
6565
1616
3232
4848
6464
1515
3131
4747
6363
1414
3030
4646
6262
1313
2929
4545
6161
12
2828
4444
6060
1111
2727
4343
5959
1010
2626
4242
5858
99
2525
41
5757
88
2424
4040
56
77
2323
3939
55
66
2222
3838
54
55
2121
3737
5353
44
2020
3636
5252
33
1919
3535
515122
111818
3434
5050
6666
1717
3333
4949
6565
1616
3232
4848
6464
1515
3131
4747
6363
1414
3030
4646
6262
1313
2929
4545
6161
1212
2828
4444
6060
1111
2727
4343
5959
1010
2626
4242
5858
99
2525
4141
5757
88
2424
4040
5656
77
2323
3939
5555
66
2222
3838
54
55
2121
3737
5353
44
2020
3636
5252
33
1919
3535
515122
111818
3434
5050
6666
1717
3333
4949
6565
1616
3232
4848
6464
1515
3131
4747
63
1414
3030
4646
6262
1313
2929
4545
6161
1212
2828
4444
6060
1111
2727
43
5959
1010
2626
4242
5858
99
2525
4141
5757
88
2424
4040
5656
77
2323
3939
5555
66
2222
3838
54
55
2121
3737
5353
44
2020
3636
5252
33
1919
3535
5122
1
3
2
!
M3
M2M5
M4
PAGE 3 OF 6
U.S. Patent No. 8,856,780 2018 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
U.S. Patent No. 8,856,780 2018 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
U.S. Patent No. 8,856,780 2018 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
U.S. Patent No. 8,856,780 2018 Honda Accord PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2015-2016 HONDA CR-V PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T005_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
U.S. Patent No. 8,856,780 2015-2016 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) ORANGE - 01
PARKING LIGHTS (-) BLUE - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: GRAY
1
VS2VS2
VS1VS1
VS4VS4
VS3VS3
M5
M4
MS2
MS1
1
2
T005_H
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
M2
M3
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
1: 28 PIN PTS CONNECTOR GRAY
2: 24 PIN IGNITION CONNECTOR GRAY
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION HARNESS
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
12
T-HARNESS / WIRING DIAGRAM - 1 OF 1
01010202030304040505060607070808090910101111121213131414151516161717181819192020
010102020303040405050606
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
RELAY
!
M3
M2M5
M4
PAGE 3 OF 8
U.S. Patent No. 8,856,780 2015-2016 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
T005_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
U.S. Patent No. 8,856,780 2015-2016 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) ORANGE - 01
PARKING LIGHTS (-) BLUE - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: GRAY
1
2
1
1122334455667788991011111212
131314141515161617171818191920202121222223232424
1011
182324
11223344556677889910101111131314 1212
25252626272728 15161617171818191920202121
6714 12
28 1521222223232424
T005_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
12V (+) RED - 14
CANH (DATA) PINK - 06
IGNITION 2 (+) BLUE - 28
GROUND (-) BROWN - 15
S-NET (DATA) YELLOW - 21
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) PURPLE - 12
CANL (DATA) BLUE - 07
START (+) RED -18
IGNITION 1 (+) BLUE - 11
ACCESSORY (+) TAN - 24
M5
M4
M2
M3
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT
06 WHITE•BLUE DOT
03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE
03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE04 WHITE/RED•BLUE DOT04 WHITE/RED•BLUE DOT05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: GRAY
2: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
!
M3
M2M5
M4
PAGE 5 OF 8
U.S. Patent No. 8,856,780 2015-2016 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
U.S. Patent No. 8,856,780 2015-2016 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
U.S. Patent No. 8,856,780 2015-2016 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
U.S. Patent No. 8,856,780 2015-2016 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017-2018 HONDA CR-V PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T008_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
PAGE 2 OF 6
U.S. Patent No. 8,856,780 2017-2018 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
112233445566778899101113131414 1212
2525262627272828 1515161617171818191920202121222223232424
2: GRAY
1
2
1
T008_W
1122334455667788991010111112121313141415151616
171718191920202121222223232424252526262727282829293030313132
11223344556677889910101111121213131414151516161717181819192020
36363737383839394040 2121222223232424252526262727282829293030313132323333343435
112233445567889910101111121213131415151617171818
3636 19192021222323242425252626272728282929303031313232333334343535
1123344556778899101011111212131314141515161617171818
3636 19192020212122222323242425252626272728282929303031313232333334343535
1234567
891011121314
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY BODY CONTROL MODULE (A)
12V (+) RED - 16
CANH (DATA) PINK - 20
GROUND (-) BLACK - 08
S-NET (DATA) LTGREEN - 35
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) YELLOW - 18
CANL (DATA) BLUE -21
START (+) YELLOW - 06
ACCESSORY (+) GRAY - 32
IGNITION 1 (+) GRAY - 02
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT - IGNITION (+)
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT01 GRAY/BLACK•BLUE DOT
03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - IGNITION (+)05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: WHITE
3: BLUE
4: BLACK
5: GRAY
6: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
1
3
2
5
6
4
IMPORTANT:
1- NO TAKEOVER AVAILABLE. ENGINE WILL SHUTDOWN UPON UNLOCK.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
PARKING LIGHT (-) GRAY - 11
LIGHTS OFF (-) PINK - 10
!
M3
M2M5
M4
PAGE 3 OF 6
U.S. Patent No. 8,856,780 2017-2018 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
U.S. Patent No. 8,856,780 2017-2018 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
U.S. Patent No. 8,856,780 2017-2018 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
U.S. Patent No. 8,856,780 2017-2018 Honda CR-V PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2014-2015 HONDA CIVIC PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T004_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
AB
PAGE 2 OF 8
U.S. Patent No. 8,856,780 2014-2015 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) ORANGE - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
VS2VS2
VS1VS1
VS4VS4
VS3VS3
M5
M4
MS2
MS1
1
2
T004_H
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
M2
M3
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
1: 28 PIN PTS CONNECTOR GRAY
2: 24 PIN IGNITION CONNECTOR GRAY
1: 28 PIN PTS HARNESS
2: 24 PIN IGNITION HARNESS
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
12
T-HARNESS / WIRING DIAGRAM - 1 OF 1
01010202030304040505060607070808090910101111121213131414151516161717181819192020
010102020303040405050606
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
RELAY
!
M3
M2M5
M4
PAGE 3 OF 8
U.S. Patent No. 8,856,780 2014-2015 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
T004_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
AB
PAGE 4 OF 8
U.S. Patent No. 8,856,780 2014-2015 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
LIGHTS OFF (-) ORANGE - 01
PARKING LIGHTS (-) GRAY - 08 112233445566
7788
1
899101011111212
HEADLAMP SWITCH (B)
1: WHITE
1
2
1
1122334455667788991011111212
131314141515161617171818191920202121222223232424
1011
182324
11223344556677889910101111131314 1212
25252626272728 15161617171818191920202121
6714 12
28 1521222223232424
T004_W
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY SMART PCU (A)
12V (+) WHITE - 14
CANH (DATA) PINK - 06
IGNITION 2 (+) YELLOW - 28
GROUND (-) BLACK - 15
S-NET (DATA) LTGREEN - 21
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) GREEN - 12
CANL (DATA) BLUE - 07
START (+) ORANGE -18
IGNITION 1 (+) WHITE - 11
ACCESSORY (+) GRAY - 24
M5
M4
M2
M3
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT
06 WHITE•BLUE DOT
03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE01 GRAY/BLACK•BLUE DOT - IGNITION 2 (+) CONNECTOR SIDE
03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE03 GRAY/RED•BLUE DOT - IGNITION 2 (+) VEHICLE SIDE04 WHITE/RED•BLUE DOT04 WHITE/RED•BLUE DOT05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: GRAY
2: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
12
IMPORTANT:
1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOTT02 BLUE•BLACK DOTT
05 GREEN/BLACK•BLACK DOTT05 GREEN/BLACK•BLACK DOTT
!
M3
M2M5
M4
PAGE 5 OF 8
U.S. Patent No. 8,856,780 2014-2015 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
U.S. Patent No. 8,856,780 2014-2015 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
U.S. Patent No. 8,856,780 2014-2015 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
U.S. Patent No. 8,856,780 2014-2015 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016-2018 HONDA CIVIC PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T007_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
PAGE 2 OF 6
U.S. Patent No. 8,856,780 2016-2018 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
112233445566778899101113131414 1212
2525262627272828 1515161617171818191920202121222223232424
2: GRAY
1
2
1
T007_W
1122334455667788991010111112121313141415151616
171718191920202121222223232424252526262727282829293030313132
11223344556677889910101111121213131414151516161717181819192020
36363737383839394040 2121222223232424252526262727282829293030313132323333343435
112233445567889910101111121213131415151617171818
3636 19192021222323242425252626272728282929303031313232333334343535
1123344556778899101011111212131314141515161617171818
3636 19192020212122222323242425252626272728282929303031313232333334343535
1234567
891011121314
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY BODY CONTROL MODULE (A)
12V (+) YELLOW - 16
CANH (DATA) PINK - 20
GROUND (-) BLACK - 08
S-NET (DATA) RED - 35
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) WHITE - 18
CANL (DATA) BLUE -21
START (+) YELLOW - 06
ACCESSORY (+) GRAY - 32
IGNITION 1 (+) PINK - 02
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT - IGNITION (+)
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT01 GRAY/BLACK•BLUE DOT
03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - IGNITION (+)05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: WHITE
3: BLUE
4: BLACK
5: GRAY
6: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
1
3
2
5
6
4
IMPORTANT:
1- NO TAKEOVER AVAILABLE. ENGINE WILL SHUTDOWN UPON UNLOCK.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
PARKING LIGHT (-) GRAY - 11
LIGHTS OFF (-) PINK - 10
!
M3
M2M5
M4
PAGE 3 OF 6
U.S. Patent No. 8,856,780 2016-2018 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
U.S. Patent No. 8,856,780 2016-2018 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
U.S. Patent No. 8,856,780 2016-2018 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
U.S. Patent No. 8,856,780 2016-2018 Honda Civic PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
U.S. Patent No. 8,856,780
20180302
REVISION DATE
FT-RSA-HA6P-[FT-DC2-S]FIRMWARE
FT-DC2-SHARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2018 HONDA ODYSSEY PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
T009_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
PAGE 2 OF 6
U.S. Patent No. 8,856,780 2018 Honda Odyssey PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
!
112233445566778899101113131414 1212
2525262627272828 1515161617171818191920202121222223232424
2: GRAY
1
2
1
T009_W
1122334455667788991010111112121313141415151616
171718191920202121222223232424252526262727282829293030313132
11223344556677889910101111121213131414151516161717181819192020
36363737383839394040 2121222223232424252526262727282829293030313132323333343435
112233445567889910101111121213131415151617171818
3636 19192021222323242425252626272728282929303031313232333334343535
1123344556778899101011111212131314141515161617171818
3636 19192020212122222323242425252626272728282929303031313232333334343535
1234567
891011121314
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY BCM, ABOVE DASH FUSEBOX (A)
12V (+) RED - 16
CANH (DATA) WHITE - 20
GROUND (-) BLACK - 08
S-NET (DATA) LTGREEN - 35
HARDWIRE / WIRING DIAGRAM - 1 OF 1
PTS (+) YELLOW - 18
CANL (DATA) TAN -21
START (+) GREEN - 06
ACCESSORY (+) GRAY - 32
IGNITION 1 (+) WHITE - 02
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT12 WHITE•BLACK DOT - PARKING LIGHTS (-) OUTPUT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
09 YELLOW - PTS (+) OUTPUT
17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
02 WHITE/BLACK•BLUE DOT - IGNITION (+)
06 WHITE•BLUE DOT
01 GREEN•BLACK DOT01 GREEN•BLACK DOT02 BLUE•BLACK DOT02 BLUE•BLACK DOT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT06 BLUE/WHITE•BLACK DOT - GWR (-) OUTPUT07 EMPTY07 EMPTY08 WHITE/PURPLE•BLACK DOT08 WHITE/PURPLE•BLACK DOT09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE
10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN - ACCESSORY (+) IN/OUT15 BROWN - ACCESSORY (+) IN/OUT16 ORANGE/BLACK - S-NET (DATA)16 ORANGE/BLACK - S-NET (DATA)
01 GRAY/BLACK•BLUE DOT01 GRAY/BLACK•BLUE DOT
03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - IGNITION (+)05 GRAY•BLUE DOT05 GRAY•BLUE DOT
1: WHITE
3: BLUE
4: BLACK
5: TAN
6: GRAY
HORN (-)
HOOD SWITCH
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
1
3
2
5
6
4
IMPORTANT:
1- NO TAKEOVER AVAILABLE. ENGINE WILL SHUTDOWN UPON UNLOCK.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
PARKING LIGHT (-) WHITE - 11
LIGHTS OFF (-) PINK - 10
!
M3
M2M5
M4
PAGE 3 OF 6
U.S. Patent No. 8,856,780 2018 Honda Odyssey PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
01
ENGINE
START
STOP
OFF ACC ON STARTON
02
03
ENGINE
START
STOP
OFF ACC ON STARTOFF
04
05
06
07
ENGINE
START
STOP
OFF ACC ON STARTON
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
>>
11
ENGINE
START
STOP
OFF ACC ON STARTSTARTSTART
12
13
14
15
16
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Set ignition to ON position.
Wait, LED 1 will flash GREEN rapidly.
Set ignition to OFF position.
WARNING: Disconnect power last. Disconnect
module from vehicle.
Connect module to computer and proceed
with extended programming.
Connect power first. Connect module to
vehicle.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2
seconds.
Set ignition to OFF position.
Press UNLOCK on the OEM remote.
If the vehicle is equipped with a power liftgate:
Open and close the power liftgate with the
OEM keyfob.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming
button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
U.S. Patent No. 8,856,780 2018 Honda Odyssey PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
U.S. Patent No. 8,856,780 2018 Honda Odyssey PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
U.S. Patent No. 8,856,780 2018 Honda Odyssey PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 FT-RSA-HA6P-[FT-DC2-S]-EN
20180302