installation 2006 civic 4 door (ex) … · © 2006 american honda motor co., inc. - all rights...

© 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 30852 (0601) 1 of 16

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

JAN 2006

08B15-SNA-1000-91

2006 CIVIC4 DOOR (EX)

XM RADIO SYSTEMAII 30852

PARTS LIST

XM Radio Attachment (sold separately):P/N 08B15-SNA-100A

BUS cable

Bracket A

Bracket B

Clip

Double-face tape

5 Pan-screws, 5 x 8 mm

5 Plain-washers, 5 mm

3 Flange-bolts, 6 x 12 mm

Coupler clip

Cover seal

20 Wire ties

7 Wire tie with clips

12 Cushion tapes

8 EPT seals

XM Antenna (sold separately):P/N: 08A15-EX5-100B

Antenna Assy

Splitter Assy

Coupler clip

2 of 16 AII 30852 (0601) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.

Unit kit (sold separately):P/N 08A15-EX5-000

XM tuner

Bus Cable 2 Port (sold separately):P/N 08A31-0F1-000

BUS cable 2 Port

TOOL AND SUPPLIES REQUIRED#2 Phillips screwdriverFlat-tip screwdriverUtility knifeDiagonal cuttersTape measureShop towelScissorsRatchet8 mm, 10 mm and 14 mm Socket8 mm, 10 mm and 14 mm Combination wrenchesIsopropyl alcohol(Isopropyl alcohol, in a 60/40 solution with water)Rubber hammerMasking tape

Illustration of the XM Radio System Installed on thevehicle

5323080H

SPLITTER

ANTENNA

XM RADIO TUNER

BUS CABLE

5323090H

COMMANDERUNIT

SPLITTER

ANTENNA

XM TUNERUNIT

BUS CABLE


INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These procedures shouldnot be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

3. Remove the passenger’s dashboard lower cover(four clips, and two pins).

5306360T

PASSENGER’SDASHBOARD

CLIPS(4)

PINS(2)

5202260T

BOLTS (2)

GLOBE BOXSTOPPERS (2)

5202121T

CLIPS(8)

DRIVER’SDASHBOARDLOWER COVER

4. Remove the two bolts under the glove box.

5. Open the globe box. Release the stoppers andremove the globe box.

6. Remove the driver’s dashboard lower cover (eightclips).


7. Remove the inside cover from the front consolepocket (two tabs).

8. Lower the steering wheel lever and pull thesteering toward you.

10. Apply masking tape to the meter panel as shown,and remove the instrument panel (one self-tappingscrews, 11 clips, and one connector).

11. Apply masking tape to the instrument panel asshown, and remove the center panel (two bolts,ten retaining clips, and unplug the vehicleconnectors).

9. To protect the dashboard area, place a shop towelover the steering wheel and shift lever.

5202130T

FRONT CONSOLEPOCKET

INSIDECOVER

TABS (2)

SIFT LEVER“S or 2” POSITION

5624100B

SELF-TAPPINGSCREW

CLIPS (11)

METER PANEL MASKING TAPE

5608031H

SHOPTOWEL

STEERINGWHEEL

SHOP TOWEL

COMBINATIONSWITCH

SIFTLEVER

TILT LEVER

5202563T

CLIPS (5)

BOLT

VEHICLECONNECTORS

CLIPS (6)

MASKING TAPE

CENTER PANEL

ASPORATORHOSE


12. Remove the weatherstrip from the opening edge ofthe right front door in the area shown.

13. Push the clip into the vehicle side by striking thetop of the right front pillar trim in the part markedas “SIDE CURTAIN AIRBAG” with the rubbermallet perpendicularly to the vehicle. Then,remove the clip.

14. Remove the weatherstrip in the area shown. Andremove the right front pillar trim (two clips).

15. Remove the cap from the right sunvisor ( fourretaining tabs).

16. Remove the right sunvisor ( two T25 Torx screws,and unplug the vehicle connectors ).

17. Remove the right and left sunvisor holders. Turnthe holders 90°, then pull it out.

18. Remove the center console cover.

A/T Vehicle

• Remove the center console cover (five clips).5718021H

FRONT PILLAR

PIN

CLIP

RUBBER HAMMERStrike perpendicularly.

WEATHERSTRIPRIGHT FRONTPILLAR TRIM

CLIP

FRONTPILLAR TRIM

5202250T

RIGHT FRONTPILLAR TRIMCLIPS (2)

WEATHERSTRIP

5321090H

CONNECTOR

RETAININGTABS (4)

CAP

TORX SCREW

RIGHT SUNVISORSUNVISORHOLDER

5202173T

CLIPS(3)

CENTERCONSOLECOVER

PARKING BRAKE LEVERPull up completely.

SHIFT LEVER(“D” position)

CLIPS (2)


M/T Vehicle

• Pull down on the shift boot. Remove the shiftknob by turning it counterclockwise.

• Remove the center console cover by removingthe five clips fastening the center consolecover.

19. Open the center console lid, and remove the mat.

20. Remove the center console (four bolts, two clips,and the vehicle connector).

21. Remove the rear seat cushion (one bolt andrelease the two hooks).

5321061H

SHIFTKNOB

SHIFT BOOT

5321072H

CLIPS (3) CENTERCONSOLECOVER

PARKING BRAKELEVERPull up completely.CLIPS

(2)

5202184T

BOLTS (4)

MAT

CLIPS (2)

CENTERCONSOLELID

VEHICLECONNECTOR

CENTERCONSOLE

5202362T

BOLT

REAR SEATCUSHION

HOOK


5202580T

CLIPS (4) RETAININGTAB (3)

FRONT

RIGHT REARSIDE STEP TRIM

5202451T

TRUNKWEATHERSTRIP

CLIP(4)

REAR TRIM PANELHOOK (3)

22. Remove the right seatside bolster (one bolt).

23. Remove the right rear side step trim (four clipsand three retaining tabs).

24. Open the trunk lid, fold the rear seatback forwardby pulling the levers under the rear parcel shelf.Remove the trunk floor mat (two clips).

25. Remove the trunk weatherstrip from the edge ofthe trunk opening in the area shown.

5202410T

RIGHTSEAT SIDEBOLSTER

BOLT5202441T

LEVERREARSEATBACK

TRUNKFLOORMAT

CLIPS (2)


26. Remove the rear trim panel (four clips and threehooks).

27. Continue removing the weatherstrip in the areashown. Remove the five clips, then pull out on theright trunk side trim panel in the direction shown.

Routing the BUS Cable

28. Route the BUS cable from the trunk along thevehicle harness.

29. Lift up and lock the right rear seatback, thenremove the clip that secures the floor carpet. Pullback the floor carpet.

30. Route the BUS cable forward under the floorcarpet.

5202472T

RIGHT TRUNKSIDE TRIM PANEL

CLIP

CLIPTurn the center pincounterclockwiseto remove.

CLIPTurn the center pincounterclockwiseto remove.

5218071H

BUSCABLE

RIGHT REARSEATBACK(without MX)

VEHICLEBRACKET

5218092H

BUS CABLERoute underthe floor carpet.

CLIP

FLOORCARPET


31. Route the BUS cable forward to the right frontconsole frame along the vehicle harness.

32. Route the BUS cable connector to the dashboardand out through the dash opening.

Routing the antenna cable

33. Using isopropyl alcohol on a shop towel, clean theantenna where the doubleside tape will attach.Remove an adhesive backing from the doublesidetape, and attach it to the antenna.

34. Using isopropyl alcohol on a shop towel, clean theright front upper corner on the inside of the frontwindow.

35. Remove the adhesive backing from the antenna,and attach the antenna to the front window at thelocation shown. Install the antenna by applyingsufficient pressure.

5221023H

BUS CABLE

DASHOPENING

DASHOPENING

VEHICLEHARNESS

5321110H

ANTENNA

DOUBLESIDE TAPE

ADHESIVEBACKING

5321120H

10 mm

3 mm

ANTENNA

<INSIDE>

ANTENNA

FRONT WINDOW


36. Using isopropyl alcohol on a shop towel, clean theright front upper corner on the outside of the frontwindow.

37. Remove the adhesive backing from the coverseal, and attach it to the out side of the frontwindow at the location shown.

38. Using scissors, cut three EPT sealers in half.

39. Route the antenna cable down the passenger’s A-pillar. Attach the antenna cable to the A-pillarpanel with the six pieces of cut EPT sealer inareas shown.

40. Route the antenna cable down behind thedashboard stay and towards the glove box. Securethe antenna cable to the vehicle harness with thethree wire ties.

41. Inside the glove box opening, route the antennacable along the vehicle harness and towards theaudio unit opening. Secure the antenna cable tothe vehicle harness with the wire tie in areasshown.

5321132H

ADHESIVEBACKING

COVERSEAL

<OUTSIDE>

“ ” MARKon the frontwindow

5 mm

5 mm

5321140H

EPT SEALER(Cut in half.)

ANTENNA

EPT SEALER(3 pieces)

EPTSEALER(3 pieces)

ANTENNACABLE

5322011H

WIRE TIE

ANTENNA CABLE VEHICLEHARNESS

EPT SEALER

VEHICLEBRACKET

DASHBOARDSTAY

5322020H

VEHICLEHARNESS

WIRE TIE

ANTENNA CABLE


42. Route the antenna cable down along the BUScable as shown.

43. Measure 300 mm from the end of the BUS cableconnector, then secure the BUS cable andantenna cable to the vehicle harness with six wireties.

44. Route the antenna cable along the BUS cable,secure the BUS cable and antenna cable to thevehicle harness with three wire ties.

45. Using isopropyl alcohol on a shop towel, clean thearea where the cushion tape will attach. Attach theBUS cable and antenna cable to the floor panelwith the two cushion tapes in the area shown.

46. Route the antenna cable along the BUS cable,turn over the floor carpet, then attach the BUScable and antenna cable to the floor panel with thetwo cushion tapes in the areas shown.

47. Secure the BUS cable and antenna cable to thevehicle harness with the three wire ties in theareas shown.

5322043H

WIRE TIE

BUS CABLECONNECTOR

ANTENNA CABLE

300 mmWIRETIE

WIRE TIE

5322051H

VEHICLEHARNESS

BUS CABLE

CUSHION TAPE

WIRE TIE

WIRE TIE

ANTENNACABLE

5322061H

CUSHIONTAPE

WIRE TIE

VEHICLEHARNESS

BUSCABLE

Turn over.

ANTENNA CABLE

BUS CABLE

<SIDE VIEW>

CUSHION TAPE


48. Route the antenna cable along the BUS cable,secure the BUS cable and antenna cable to thevehicle harness with the two wire ties in the areasshown.

49. Attach the BUS cable and antenna cable to thefloor panel with the four cushion tapes in the areasshown.

50. Route the BUS cable and the antenna cable up onthe right trunk inner panel. Loosely secure them tothe holes of the panel with the three wire ties withclip.

Installing the XM Tuner unit

51. Install the bracket A and B to the XM tuner withfour 5 x 8 mm washer-screws.

5322090H

BRACKET A

BRACKET B

WASHER-SCREW

XM TUNER

2-PINCONNECTORLOCATION

14-PIN CONNECTORLOCATION

WASHER-SCREW

5322071H

WIRETIE

BUS CABLE ANDANTENNA CABLE

VEHICLE HARNESS

RIGHT REARSEATBACK(without MX)

VEHICLE BRACKET

CUSHIONTAPE

CUSHIONTAPE

5322081H

WIRE TIEWITH CLIP

BUSCABLE

HOLE

ANTENNACABLE


5322100H

XM TUNER

BRACKET A

SPLITTER1-PINCONNECTOR


DOUBLESIDETAPE

ADHESIVEBACKING

5 x 8 mmWASHER-SCREW

SPLITTER

5323010H

BRACKET A


COUPLERCLIP

SPLITTER

XM TUNER

2-PINCONNECTOR

52. Using isopropyl alcohol on a shop towel, clean theXM tuner where the splitter will attach. Removethe adhesive backings from the double-face tape,and install the splitter to the XM tuner with thedouble-side tape at the location shown. Secure thesplitter to the bracket A with one 5 x 8 mmwasher-screw.

53. Plug the splitter 2-pin connector into the XM tuner.

54. Install the connector clip to the splitter 1-pinconnector, and then Insert it into the bracket Ahole in the area shown.

55. Using isopropyl alcohol on a shop towel, clean theright trunk inner panel where the EPT sealer willattach. And attach it to the right trunk inner panelat the location shown.

56. Route the BUS cable and the antenna cablethrough the hole of the right trunk inner panel.

57. Plug the Bus cable connector into the XM tunerand the antenna cable connector to the splitter1-pin connector.

58. Attach the antenna cable on the XM tuner with thecushion tape in the area shown.

5323021H

EPTSEALER

RIGHT TRUCKINNER PANEL

5323031H

RIGHT TRUCKINNER PANEL

XM TUNER

BUS CABLE

ANTENNACABLE

BUS CABLE14-PIN CONNECTOR

ANTENNA CABLE1-PIN CONNECTOR

CUSHIONTAPE


59. Loosely attach three 6 x 12 mm flange-bolts to thebracket A and B as shown.

60. Place the XM radio assembly to back of the righttrunk inner panel. Set the three 6 x 12 mm flange-bolts into the elongated holes in the body panel.Tighten the three 6 x 12 mm flange-bolts.

61. Fold the excess BUS cable and antenna cableand secure them with the two wire ties with clipinstalled in step 51.

62. Secure the BUS cable and the antenna cable tothe holes on the right trunk inner panel with thethree wire ties with clip.

If the vehicle you’re working on is equipped withCD Changer, go to step 63; otherwise, continue withstep 65.

63. Plug in the BUS cable 2 port connectors the twoBUS cables respectively.

64. Wrap the two plugged connectors with the twoEPT sealers respectively.

5420060H

BUS CABLE2 PORT

BUS CABLES (2)

EPT SEALERS (2)

5323042H

ELONGATEDHOLE

XM TUNER

RIGHTTRUNKINNERPANEL

6 x 12 mmFLANGEBOLTS (3)

5323051H

installedin step 50.

WIRE TIEWITHCLIPS (3)

Hold theexcesscables.

WIRE TIE WITH CLIPinstalled Step 51.


65. Plug the BUS cable connector into the rear of theaudio unit.

<Standard Audio Unit>

<Navigation System Unit>

66. Connect the vehicle connectors to the centerpanel, and reinstall the center panel.

67. Exchange the old clip to a new one on the rightfront pillar trim.

5801030H

BUS CABLE

HEAD UNIT

5801010H

BUS CABLE

AUDIO UNIT

5420071H

CENTER PANEL

VEHICLE CONNECTORS

BOLT(Reused)

5323070H

NEW CLIP

OLD CLIP(Discard.)

RIGHT FRONTPILLAR TRIM


68. Check that all wire harnesses are routed properlyand all connectors are plugged in.

69. Reconnect the negative cable to the battery.

70. Enter the customer’s radio anti-theft code, andreset the radio station presets.

71. Set the clock.

72. Check the operation of the XM radio systemaccording to the vehicle’s Owner’s Manualsupplied.

73. Reinstall all removed parts.

NOTE: When the battery is disconnected, the driver’swindow AUTO function is disabled.

• Start the engine. Push down on the driver’s windowswitch until the window is fully open.

• Pull up on the driver’s window switch to close thewindow completely, then hold the switch for 2seconds or more.

• Lower and raise the driver’s window to checkoperation of the driver’s window AUTO function.

installation 2006 civic 4 door (ex) … · © 2006 american honda motor co., inc. - all rights...

Documents