installation guide - download.h3c.com
TRANSCRIPT
H3C MSR900-E RoutersInstallation Guide
New H3C Technologies Co., Ltd. http://www.h3c.com.hk Document version: 6W102-20170613
Copyright © 2017, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow, SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage, use, and disposal of this product must meet the applicable national laws and regulations.
Preface
The H3C MSR900-E Routers Installation Guide includes five chapters, which describe the preparing for installation, installing the router, troubleshooting, chassis views and technical specifications, and LEDs.
This preface includes the following topics about the documentation:
• Audience.
• Conventions.
• Obtaining documentation.
• Technical support.
• Documentation feedback.
Audience This documentation is intended for:
• Network planners.
• Field technical support and servicing engineers.
• Network administrators working with the MSR900-E Routers
Conventions The following information describes the conventions used in the documentation.
Command conventions
Convention Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... } Braces enclose a set of required syntax choices separated by vertical bars, from which you select one.
[ x | y | ... ] Square brackets enclose a set of optional syntax choices separated by vertical bars, from which you select one or none.
{ x | y | ... } * Asterisk marked braces enclose a set of required syntax choices separated by vertical bars, from which you select a minimum of one.
[ x | y | ... ] * Asterisk marked square brackets enclose optional syntax choices separated by vertical bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention Description
Boldface Window names, button names, field names, and menu items are in Boldface. For example, the New User window opens; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.
Symbols
Convention Description
WARNING An alert that calls attention to important information that if not understood or followed can result in personal injury.
CAUTION An alert that calls attention to important information that if not understood or followed can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT An alert that calls attention to essential information.
NOTE An alert that contains additional or supplementary information.
TIP An alert that provides helpful information.
Network topology icons
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access controller engine on a unified wired-WLAN switch.
Represents an access point.
Wireless terminator unit.
Wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
TT
TT
Represents a security product, such as a firewall, UTM, multiservice security gateway, or load balancing device.
Represents a security module, such as a firewall, load balancing, NetStream, SSL VPN, IPS, or ACG module.
Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model, configuration, or software version. It is normal that the port numbers, sample output, screenshots, and other information in the examples differ from what you have on your device.
Obtaining documentation To access the most up-to-date H3C product documentation, go to the H3C website at http://www.h3c.com.hk.
To obtain information about installation, configuration, and maintenance, click
http://www.h3c.com.hk/Technical_Documents
To obtain software version information such as release notes, click
http://www.h3c.com.hk/Software_Download
Technical support [email protected]
http://www.h3c.com.hk
Documentation feedback You can email your comments about product documentation to [email protected].
We appreciate your comments.
i
Contents
Preparing for installation ············································································································································· 1 Safety recommendations ·················································································································································· 1 Examining the installation site ········································································································································· 1
Temperature and humidity ······································································································································· 1 Cleanliness ································································································································································ 1 Cooling system ························································································································································· 2 ESD prevention ························································································································································· 2 EMI ············································································································································································· 2 Lightning protection ·················································································································································· 3
Installation accessories and tools ···································································································································· 3 Pre-installation checklist ···················································································································································· 4
Installing the router ······················································································································································· 5 Installation prerequisites ··················································································································································· 5 Installation flow ································································································································································· 5 Installing the router ···························································································································································· 6
Mounting the router on a workbench ····················································································································· 6 Installing the router on a wall ·································································································································· 7 Installing the router in a rack ·································································································································· 8
Grounding the router ····················································································································································· 10 Attaching the ring terminal ··································································································································· 11 Grounding the router through the rack ··············································································································· 11 Grounding the router with a grounding strip ····································································································· 13 Grounding the router with a grounding conductor buried in the earth ground ············································· 14 Installing a WLAN antenna ·································································································································· 14
Connecting interface cables ········································································································································· 15 Connecting an Ethernet cable ······························································································································ 15 Connecting optical fibers ····································································································································· 16 Connecting USB devices ······································································································································· 16
Connecting a console cable and setting terminal parameters ·················································································· 17 Connecting a console cable ································································································································· 17 Setting terminal parameters ·································································································································· 18
Connecting the power cord ·········································································································································· 18 Verifying the installation ················································································································································ 19 Powering on the router ·················································································································································· 19
Displaying boot information ································································································································· 19 Checking after power-on ······································································································································ 21 Configuring basic settings for the router ············································································································· 21
Troubleshooting ·························································································································································· 22 Power supply failure ······················································································································································ 22 System configuration problems ····································································································································· 22
No terminal display ·············································································································································· 22 Garbled terminal display ······································································································································ 23 No response from the serial port ························································································································· 23
Restoring the factory settings ········································································································································ 23 Scenario 1 ······························································································································································ 23 Scenario 2 ······························································································································································ 24 Scenario 3 ······························································································································································ 24 Reset button usage guidelines ······························································································································ 24
ii
Appendix A Chassis views and technical specifications ························································································ 25 Chassis views ································································································································································· 25
MSR900-E ······························································································································································ 25 MSR900-E-W ························································································································································· 26
Technical specifications ················································································································································· 26 Antenna specifications ··················································································································································· 27
Appendix B LEDs ························································································································································ 28 LEDs ················································································································································································· 28
MSR900-E ······························································································································································ 28 MSR900-E-W ························································································································································· 28
LED description ······························································································································································· 29
Index ··········································································································································································· 30
1
Preparing for installation
Safety recommendations WARNING!
Before installation and operation, read all of the safety instructions in Compliance and Safety Guide supplied with your router.
Follow these general safety recommendations:
• Turn off all power and remove all power cables before opening the chassis.
• Unplug all power and external cables before moving the chassis.
• Before installation, locate the emergency power switch so that you can shut off power immediately if necessary.
• Always wear an ESD wrist strap when installing the router.
• Do not stare into an open optical interface. The light can cause permanent eye damage.
• Use a good grounding system. This is essential for reliable operation.
• Make sure the resistance reading between the chassis and the ground is less than 1 ohm.
Examining the installation site The H3C MSR900-E router can only be used indoors. To ensure that the router can operate correctly and prolong its service lifetime, the installation site must meet the following requirements.
Temperature and humidity Table 1 Temperature and humidity requirements
Temperature Relative humidity
0°C to 40°C (32°F to 104°F) 5% to 90%
Cleanliness Table 2 Dust concentration limit in the equipment room
Substance Concentration limit (particles/m3)
Dust particles ≤ 3 x 104 (No visible dust on desk in three days)
NOTE:
Dust particle diameter ≥ 5 μm
2
Table 3 Harmful gas concentration limits
Gas Max. (mg/m3)
SO2 0.2
H2S 0.006
NH3 0.05
Cl2 0.01
Cooling system To ensure good ventilation, the installation site must meet the following requirements:
• A minimum clearance of 10 cm (3.94 in) is reserved at the inlet and outlet air vents.
• The site has an adequate cooling system.
ESD prevention
CAUTION:
Make sure the resistance reading between human body and the ground is in the range of 1 to 10 megohms (Mohms).
To prevent the electronic components from being damaged by ESD, follow these guidelines:
• Make sure the router and the floor are reliably grounded.
• Take dust-proof measures for the equipment room.
• Always wear an ESD wrist strap when touching a circuit board.
To attach an ESD wrist strap:
1. Wear the wrist strap on your wrist.
No wrist strap is supplied with the router. Prepare it yourself.
2. Lock the wrist strap tight around your wrist to keep good contact with the skin.
3. Secure the wrist strap lock and the alligator clip lock together.
4. Attach the alligator clip to the grounding terminal on the device.
EMI EMI from any source adversely affects the router.
To prevent EMI, use the following guidelines:
• Use electromagnetic shielding when necessary.
• Take measures against interference from the power grid.
• Do not use the router together with the grounding or lightning-prevention equipment of power equipment, and keep the router far away from them.
• Keep the router far away from radio transmitting stations, radar stations, and high-frequency devices.
3
Lightning protection To protect the router from lightning, use the following guidelines:
• Make sure the grounding cable of the chassis is grounded reliably.
• Make sure the grounding terminal of the AC power receptacle is grounded reliably.
• Install a lightning arrester at the input end of the power supply.
Installation accessories and tools Figure 1 and Figure 2 list the accessories and tools required for installing the router.
Figure 1 Installation accessories
NOTE:
The type of the antenna that comes with the router depends on the router model.
Figure 2 User-supplied tools and equipment
Cage nut (user-supplied)
Ring terminal (provided)
M6 screw (user-supplied)
M4 countersunk-head screw
(provided)
Rubber feet (provided)
Mounting brackets (provided)
Grounding screw (provided)
Antenna
Screw anchor and screw
(user-supplied)
Bail latch
Flathead screwdriver Phillips screwdriver Needle-nose pliers Wire-stripping pliers
ESD wrist strap Heat gun Drill
Claw hammer
MarkerDiagonal pliers
4
Pre-installation checklist Table 4 Pre-installation checklist
Item Requirements Result
Installation site
Ventilation
• There is a minimum clearance of 10 cm (3.94 in) around the router chassis inlet and outlet vents for heat dissipation.
• The installation site ventilation system is adequate.
Temperature 0°C to 45°C (32°F to 113°F)
Relative humidity 5% to 90% (noncondensing)
Cleanliness Dust concentration ≤ 3 × 104 particles/m3
ESD prevention
• The equipment and floor are reliably grounded. • The equipment room is dust-proof. • The humidity and temperature are in the acceptable
range. • Wear an ESD wrist strap when touching a circuit
board.
EMI prevention
• Take measures to protect the power system from the power grid system.
• Keep the protection ground of the router as far away from the grounding device or lightning protection grounding device as possible.
• Keep the router far away from radio transmitters, radar, and high-frequency or high-voltage devices.
• Use electromagnetic shielding when necessary.
Lightning protection
• The grounding cable of the chassis is grounded reliably.
• The grounding terminal of the AC power receptacle is grounded reliably.
• A port lightning arrester is installed. (Optional.) • A power lightning arrester is installed. (Optional.) • A signal lightning arrester is installed at the input end
of an external signal cable. (Optional.)
Electricity safety • Install an uninterrupted power supply (UPS). • In case of emergency during operation, switch off the
external power switch.
Workbench • The workbench is stable. • The workbench is reliably grounded.
Safety precautions
• The router is far away from any heat or moisture sources. • The emergency power switch in the equipment room is identified and
accessible.
Tools • Installation accessories supplied with the router are ready. • User-supplied tools are ready.
Reference • Documents shipped with the router are available. • Online documents are available.
5
Installing the router
WARNING!
To avoid injury, do not touch bare wires, terminals, or parts with high-voltage hazard signs.
IMPORTANT:
• The barcode on the router chassis contains product information that must be provided to local sales agent before you return a faulty router for service.
• Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence.
Installation prerequisites • You have read "Preparing for installation" carefully.
• All requirements in "Preparing for installation" are met.
Installation flow You can install the router on a workbench, on a wall, or in a rack. Select an installation method according to the installation environment, and follow the installation flowchart shown in Figure 3.
6
Figure 3 Installation flow
Installing the router
Mounting the router on a workbench
IMPORTANT:
• Reserve a clearance of 10 cm (3.94 in) around the router for heat dissipation.
• Do not place heavy objects on the router.
7
To mount the router on a workbench:
1. Make sure the workbench is clean, stable, and reliably grounded.
2. Place the router upside down on the workbench and attach the rubber feet to the four round holes in the chassis bottom.
Figure 4 Attaching the rubber feet
3. Place the router on the workbench upside up.
Installing the router on a wall
CAUTION:
Make sure the network interfaces on the router face downwards, and the sides with ventilation openings are perpendicular to the ground, as shown in Figure 5.
To mount the router on a wall:
1. Mark the locations of the two mounting holes on the wall with a separation of 160 mm (6.30 in).
The holes must be level (on the same horizontal line.)
2. Drill two holes with a minimum depth of 22 mm (0.87 in) at the marked positions.
3. Hammer a screw anchor into each hole.
4. Fasten a screw into each anchor. Do not fasten the screw all the way in. Leave a space of at least 1.5 mm (0.06 in).
5. Align the installation holes at the router rear with the screws on the wall and rest the router on the screws.
8
Figure 5 Mount the router on a wall
Installing the router in a rack
CAUTION:
To avoid damages to the router and mounting brackets, do not place any objects on the router.
To install the router in a rack:
1. Use a mounting bracket to mark the locations of cage nuts on the front rack posts, as shown in Figure 6.
The mounting brackets on both front rack posts must be level (on the same horizontal line.)
9
Figure 6 Marking installation holes for cage nuts
2. Install cage nuts on rack posts, as shown in Figure 7.
a. Insert one ear of a cage nut into a marked installation hole.
b. Use a flathead screwdriver to push the other ear into the same hole.
Figure 7 Installing cage nuts
3. Attach the mounting brackets to both sides of the router, as shown in Figure 8.
10
Figure 8 Securing mounting brackets to the router
4. Use M6 screws to secure both mounting brackets on the router to the front rack posts, as shown in Figure 9.
Figure 9 Securing the router to the rack
Grounding the router WARNING!
Connecting the router grounding cable correctly is crucial for protecting the router from lightning and EMI.
Make sure the grounding resistance is less than 5 ohms.
You can ground the router with a grounding strip or with a grounding conductor buried in the earth ground.
The router provides only a ring terminal but no grounding cable. Purchase a grounding cable if necessary.
11
Attaching the ring terminal 1. Cut the grounding cable as appropriate for connecting to the grounding strip.
2. Peel 5 mm (0.20 in) of insulation sheath by using the wire-stripping pliers, and insert the bare metal part through the black insulation covering into the end of the ring terminal.
3. Secure the metal part of the cable to the ring terminal with needle-nose pliers.
4. Cover the joint with the insulation covering, and heat the insulation covering with a heat gun to completely cover the metal part.
Figure 10 Attaching the ring terminal
Grounding the router through the rack 1. Make sure the rack is reliably grounded.
2. Remove the grounding screw from the grounding terminal on the router chassis.
3. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding terminal.
4. Use a screwdriver to fasten the grounding screw.
5. Remove a nut from the grounding post of the rack.
6. Use the needle-nose pliers to bend the bare wire at the other end of the grounding cable.
7. Hook the grounding cable to the grounding post on the rack, and fasten the nut.
1 2
3 4
5 6
5mm
Grounding cable Ring terminal Insulation covering
12
Figure 11 Connecting the grounding cable to the router
Figure 12 Grounding the router through the rack
13
Figure 13 Connecting the grounding cable to the rack
Grounding the router with a grounding strip 1. Remove the grounding screw from the router chassis.
2. Attach the ring terminal of the grounding cable to the grounding screw.
3. Use a screwdriver to fasten the grounding screw.
4. Remove a nut from the post on the grounding strip.
5. Use the needle-nose pliers to bend the bare wire at the other end of the grounding cable.
6. Hook the grounding cable to the post on the grounding strip, and fasten the nut.
14
Figure 14 Grounding the router to a grounding strip
Grounding the router with a grounding conductor buried in the earth ground
If the installation site does not have any grounding strips, but earth ground is available, hammer a 0.5 m (1.64 ft) or longer angle iron or steel tube into the earth to serve as a grounding conductor. See Figure 15.
Figure 15 Grounding the router with a conductor buried in the earth ground
Installing a WLAN antenna
CAUTION:
To avoid antenna damage, do not use extra force when installing an antenna.
15
Only the MSR900-E-W supports WLAN antennas.
To install a WLAN antenna:
1. Align the antenna with the antenna connector on the router and fasten the antenna onto the connector.
2. Change the antenna orientation to vertical to achieve better signal coverage.
Figure 16 Installing a WLAN antenna
Connecting interface cables
Connecting an Ethernet cable Because fixed Ethernet ports support MDI/MDIX autosensing, you can use either a straight-through cable or a crossover cable for connection.
To connect an Ethernet cable:
1. Connect one end of the cable to an Ethernet port on the router.
2. Connect the other end of the cable to the peer device.
3. Examine the port LED status. For more information, see "LED description."
Figure 17 Connecting the router to a computer
16
Connecting optical fibers
WARNING!
To avoid injury to your eyes, do not stare at any fiber port or any open apertures of a fiber when connecting optical fibers.
IMPORTANT:
• Use only H3C-certified transceiver modules.
• Ensure a minimum curvature radius of 10 cm (3.94 in) for the optical fibers.
To connect optical fibers to a fiber port:
1. Remove the dust plug from the fiber port.
2. Insert a transceiver module to the fiber port, as shown in callout 2 of Figure 18.
3. Insert LC connectors of the optical fibers to the Rx and Tx ports of the transceiver module.
4. Connect the other ends of the optical fibers to corresponding ports of the transceiver module on the peer device.
Make sure the Rx port of a transceiver module is connected to the Tx port of the peer transceiver module.
5. Examine the port LED status. For more information, see "LED description."
Figure 18 Connecting optical fibers to a fiber port
NOTE:
• Keep the connector on the optical fiber clean.
• Insert the dust plug to the fiber port if no optical fiber is connected to the port.
Connecting USB devices
CAUTION:
To avoid data loss and hardware damages, do not unplug a USB device during data transmission.
1 2 3
17
IMPORTANT:
• Use H3C-certified USB devices.
• The USB port does not support hot-swapping of the USB modem from Sierra Wireless.
To connect a USB device to the USB port:
1. Remove the cap of the USB device.
2. Insert the USB device to the USB port.
Figure 19 Connecting a USB device
Connecting a console cable and setting terminal parameters
Connecting a console cable
CAUTION:
When using a console cable to connect a PC to the router, first connect the DB-9 end of the console cable to the PC serial port. Then connect the RJ-45 connector of the console cable to the router console port.
To connect a console cable, as shown in Figure 20:
1. Select a console terminal. The console terminal can be an ASCII terminal with an RS232 serial port or a PC. (A PC is more commonly used.)
2. Connect the DB-9 connector (female) of the console cable to the RS-232 serial port of the console terminal and the RJ-45 connector to the console port of the router.
18
Figure 20 Connecting the console cable
Setting terminal parameters To access the device from the console port, you must run a terminal emulator program (HyperTermial, PuTTY, or Tera Term) on the configuration terminal. For information about using a terminal emulator program, see the program's user guide.
The following are the required terminal settings:
• Baud rate—9600.
• Data bits—8.
• Stop bits—1.
• Parity—none.
• Flow control—none.
Connecting the power cord 1. Make sure the router is reliably grounded. For more information, see "Grounding the router."
2. Connect the AC power cord connector to the AC power receptacle on the router.
3. Connect the other end of the AC power cord to the AC power supply.
19
Figure 21 Connecting the AC power cord
Verifying the installation After you complete the installation, verify the following information:
• There is enough space around the router for heat dissipation.
• The router is mounted securely on the wall, on a sturdy workbench, or in a sturdy rack.
• Antennas, USB devices, and interface modules are installed correctly.
• The router and power module are grounded reliably.
• The power supply meets requirements.
• The router is connected correctly to the console terminal and other devices and parameters are configured correctly on the console terminal.
Before starting up the router, set up the console terminal as described in "Connecting a console cable and setting terminal parameters."
Powering on the router WARNING!
Before powering on the router, locate the power source switch so that you can cut off power promptly in case of an emergency.
• Switch on the power source.
• Turn on the power switch on the router.
Displaying boot information After power-on, the router initializes its memory, and then runs the extended BootWare. The console terminal screen displays the following information: System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extend BootWare
Do you want to check SDRAM? [Y/N]
20
****************************************************************************
* *
* H3C MSR900-E BootWare, Version 1.01 *
* *
****************************************************************************
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.
Compiled Date : Jan 10 2014
CPU ID : 0xa
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
Memory Type : DDR3 SDRAM
Memory Size : 256MB
Memory Speed : 533MHz
Flash Size : 128MB
PCB Version : 2.0
BootWare Validating...
Press Ctrl+B to enter extended boot menu...
Starting to get the main application file--flash:/MSR900-E-cmw520-a2511.bin!..
............................................................................
...............
The main application file is self-decompressing.............................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
Done!
System application is starting...
................................................................................
................................................................................
................................................................................
.........
User interface con0 is available.
Press ENTER to get started.
Press Enter and the system displays the following prompt: <Sysname>
This prompt indicates that the router has entered user view and is ready to configure.
21
Checking after power-on After powering on the router, verify the following items:
• The LEDs on the front panel are normal, as described in "LED description."
• The console terminal displays information correctly. You can see the startup window on the local console terminal. For more information, see "Displaying boot information."
• After completing the POST, the system prompts you to press Enter. When the command line prompt appears, the router is ready to configure.
Configuring basic settings for the router After the router is powered on for the first time, configure basic settings for the router. For more information, see H3C MSR Series Routers Configuration Guides and H3C MSR Series Routers Command References.
22
Troubleshooting
IMPORTANT:
• The barcode on the router chassis contains product information that must be provided to local sales agent before you return a faulty router for service.
• Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any consequence.
Power supply failure Symptom
The router cannot be powered on and LEDs on the front panel are off.
Solution
To resolve the issue:
1. Power off the router.
2. Verify that the router's power cords are connected firmly.
3. Verify that the power source is operating correctly.
4. Determine if the power cord is damaged.
5. If the issue persists, contact H3C Support.
System configuration problems If the configuration environment setup is correct, the console terminal displays boot information when the router is powered on. If the setup is incorrect, the console terminal displays nothing or garbled text.
No terminal display Symptom
The console terminal displays nothing when the router is powered on.
Solution
To resolve the issue:
1. Verify that the power supply system is operating correctly.
2. Verify that the console cable is connected correctly.
3. Verify that the console cable is connected to the serial port of the console terminal.
4. Verify that the following terminal settings are correct:
Bits per second—9600.
Data bits—8.
23
Parity—None.
Stop bits—1.
Flow control—None.
Terminal Emulation—VT100.
5. Verify that the console cable is operating correctly.
6. If the issue persists, contact H3C Support.
Garbled terminal display Symptom
Terminal display is garbled.
Solution
To resolve the issue:
1. Make sure the Data bits field for the console terminal is set to 8. If the Data bits field is set to 5 or 6, the console terminal will display garbled characters.
2. If the issue persists, contact H3C Support.
No response from the serial port Symptom
The serial port gives no response.
Solution
To resolve the issue:
1. Verify that the serial cable is in good condition and the serial port settings are correct.
2. If the issue persists, contact H3C Support.
Restoring the factory settings
Scenario 1 Symptom
When you replace the router, the router password is lost. As a result, you cannot log in to the router and do not know the router configuration.
Solution
Because the router is replaced, you do not need to save the configuration of the router. In this case, you can press the Reset button for more than 4 seconds to reboot the router and restore the factory settings. Then, you can use the username and password shipped with the router to log in to the router.
When the router configuration must be saved and you have a console cable, you can log in to the router from the BootWare menu.
24
Scenario 2 Symptom
After the configuration is modified, the network connectivity is lost. When you check the configuration, the configuration is very complicated and it is hard to locate the errors. In this case, you must configure the router again.
Solution
If you have not saved any configuration, you can reboot the router by pressing the Reset button for a short time or power off the router.
If you have saved the configuration, delete the configuration file at the CLI, and press the Reset button to restore the factory settings.
Scenario 3 Symptom
The router crashes.
Solution
Press the Reset button for a short time to reboot the router.
Reset button usage guidelines An MSR900-E router provides the Reset button. You can use the button to reboot the system or restore the factory settings.
• Press the Reset button for a short time to reboot the router.
• Press the Reset button for more than 4 seconds to reboot the router and restore the factory settings.
25
Appendix A Chassis views and technical specifications
Chassis views The following figures are for illustration only.
MSR900-E Figure 22 Front view
(1) Power receptacle (2) GE LAN ports (GE1 to GE4) (3) GE WAN port (GE0) (4) GE WAN fiber port (SFP0) (5) Console port (6) Reset button (7) USB port
Figure 23 Rear view
(1) Grounding screw
1 2 3 4 5 6 7
1
26
MSR900-E-W Figure 24 Front view
(1) Power receptacle (2) GE LAN ports (GE1 to GE4) (3) GE WAN port (GE0) (4) GE WAN fiber port (SFP0) (5) Console port (6) Reset button (7) USB port
Figure 25 Rear view
(1) Grounding screw (2) WLAN antenna port (3) WLAN antenna port
Technical specifications Item MSR900-E MSR900-E-W
Console port 1 1
USB port 1 1
GE WAN port 1 1
GE LAN port 4 4
SFP port 1 1
WLAN module N/A 1
Reset button 1 1
Memory 256 MB DDR3 256 MB DDR3
Flash 128 MB 128 MB
27
Item MSR900-E MSR900-E-W
Dimensions (H × W × D) (excluding rubber feet and mounting brackets)
43.6 × 266 × 161 mm (1.72 x 10.47 x 6.34 in)
43.6 × 266 × 161 mm (1.72 x 10.47 x 6.34 in)
Rated voltage of the AC power 100 VAC to 240 VAC @ 50 Hz or 60 Hz
100 VAC to 240 VAC @ 50 Hz or 60 Hz
Rated AC power 15 W 15 W
Operating temperature 0°C to 40°C (32°F to 104°F) 0°C to 40°C (32°F to 104°F)
Relative humidity (non-condensing) 5% to 90% 5% to 90%
Antenna specifications Table 5 WLAN antenna specifications
Item Specification
Frequency range 2.4 GHz to 2.5 GHz
Voltage standing wave ratio (VSWR) 1.92:1
Input impedance 50 ohms
Gain 2 dBi
Max power consumption 2 W
Input interface SMA
Length 108 mm (4.25 in)
Color Black
Weight 8.636 g (0.20 lb)
Operating temperature –10°C to +60°C (14°F to +140°F)
28
Appendix B LEDs
LEDs
MSR900-E Figure 26 Front panel LEDs
(1) GE port status LED (yellow) (2) GE port status LED (green) (3) System status LED (4) VPN LED (5) SFP port status LED
MSR900-E-W Figure 27 Front panel LEDs
(1) GE port status LED (yellow) (2) GE port status LED (green) (3) System status LED (4) VPN LED (5) WLAN LED (6) SFP port status LED
29
LED description LED Status Description
System status LED
Off No power input, or exceptions have occurred.
Steady green The SDRAM is performing self-test.
Flashing green (8 Hz) The system software image is being copied and decompressed.
Flashing green (1 Hz) Comware has started with the configuration file and the router has booted up.
Flashing yellow (1 Hz) The SDRAM has failed the self-test.
Flashing yellow (8 Hz) The extended segment does not exist.
Steady yellow The system software image does not exist.
VPN LED Off No IPSec VPN tunnel is present.
Steady on A minimum of one IPSec VPN tunnel is present..
WLAN status LED
Off No link is present.
Steady green The radio interface is connected.
Flashing green Data is being received or transmitted.
SFP port LED
Off No link is present.
Steady green A 1000-Mbps link is present.
Flashing green Data is being received or transmitted at 1000 Mbps.
Steady yellow A 10/100-Mbps link is present.
Flashing yellow Data is being received or transmitted at 10/100 Mbps.
GE port status LED
Off No link is present.
Steady green A 1000-Mbps link is present.
Flashing green Data is being received or transmitted at 1000 Mbps.
Steady yellow A 10/100-Mbps link is present.
Flashing yellow Data is being received or transmitted at 10/100 Mbps.
30
Index
A C D E G I L M N R S T A
Attaching the ring terminal,11
C
Checking after power-on,21 Cleanliness,1 Configuring basic settings for the router,21 Connecting a console cable,17 Connecting an Ethernet cable,15 Connecting optical fibers,16 Connecting USB devices,16 Cooling system,2
D
Displaying boot information,19
E
EMI,2 ESD prevention,2
G
Garbled terminal display,23 Grounding the router through the rack,11 Grounding the router with a grounding conductor buried in the earth ground,14 Grounding the router with a grounding strip,13
I
Installing a WLAN antenna,14 Installing the router in a rack,8 Installing the router on a wall,7
L
Lightning protection,3
M
Mounting the router on a workbench,6 MSR900-E,28 MSR900-E,25 MSR900-E-W,28 MSR900-E-W,26
N
No response from the serial port,23 No terminal display,22
R
Reset button usage guidelines,24
S
Scenario 1,23 Scenario 2,24 Scenario 3,24 Setting terminal parameters,18
T
Temperature and humidity,1