INSTALLATION GUIDE

TA-4800

TABLE OF CONTENTS

What’s in the box?

Single Bass/Dual Bass Receiver Setup

SoundShaker Amplifier Setup

Commonly Asked Questions

Wireless Syncing

1

2

3

4

5

Page 1

Part No. 5102Amplifier

Part No. 5024Transmitter

Part No. 5465 Power Supply for Amplifier

Part No. 5423Power Supply for Transmitter

Part No. 8091Amp Base

Part No. 3120Long Cable

Part No. 3031Y-Cable (M/2F)

Part No. 3032Y-Cable (M/2M)

WHAT’S IN THE BOX?

Page 2

SINGLE BASS OUT RECEIVER SETUPThis is the transmitter setup for a single bass out. Please follow each step to ensure that your transmitter and amplifier are connected correctly.

STEP 3. CONNECT YOUR RECEIVER & SUBWOOFER

STEP 2. CONNECT THE 3032 Y-CABLE

STEP 2. CONNECT THE 3031 Y-CABLEConnect the single end of the 3032 Y-Cable to one split end of the 3031 Y-Cable.

Connect the single end of the 3032 Y-Cable to your receiver.

STEP 3. CONNECT THE 3032 Y-CABLE TO YOUR RECEIVER & SUBWOOFERConnect the remaining ends of the 3031 Y-Cable to both your receiver and your subwoofer. Once all connections are secure power up the transmitter.

Connect your receiver to your subwoofer. Once all connections are secure power up the transmitter.

STEP 1. CONNECT THE 3032 Y-CABLE AND POWER SUPPLY

STEP 1. CONNECT THE 3032 Y-CABLE AND POWER SUPPLYConnect the power supply for the transmitter.Connect the split cable end of the 3032 Y-Cable to the Audio In on the transmitter.

Connect the power supply for the transmitter.Connect the split cable end of the 3032 Y-Cable to the Audio In on the transmitter.

3032 Y-Cable

5423 Power Supply

3032 Y-Cable

3031 Y-Cable

Your Receiver

Your Receiver

Your Subwoofer

Your Subwoofer

1

1

2

2

3

3

5024 Transmitter

OFF-ON CODE

DUAL BASS OUT RECEIVER SETUPThis is the transmitter setup for a double bass out. Please follow each step to ensure that your transmitter and amplifier are connected correctly.

Cable Not Included

Cable Not Included

5024 Transmitter

5423 Power Supply

OFF-ON CODE

Page 3

Connect the 3120 Long Cable to the SoundShaker port on the back of the 5012 Amplifier.

STEP 5. CONNECT THE LONG CABLE AND POWER SUPPLY

STEP 6a-6b. CONNECT THE LONG CABLE TO SHORT CABLES

STEP 7a-7b. CONNECT SHORT CABLES TO SOUNDSHAKER(S)

The 3120 Long Cable attaches to the 81-3108 Short Cables.

Connect Power Supply to 15V DC Port on the back of SoundShaker

Amplifier.

NOTE: You can connect up to a total of 4 SoundShakers to each amplifier.

Finish by connecting each SoundShaker to a 81-3108 short cable.

SoundShaker 1

SoundShaker 2

SoundShaker 3

SoundShaker 4

AUDIO-IN 15V DC TRANSDUCERS

POWER X-OVER WIRELESS CODE

OFF

1

2

34

56

7

8

9

10 50HZ

55HZ

60HZ

65HZ

70HZ75HZ

80HZ

85HZ

90HZ

95HZ

100HZ

SOUNDSHAKER AMPLIFIER SETUPThis is the main amplifier setup. Please follow each to step to ensure that your amplifier is installed correctly. Make sure the transmitter is installed and is sending a signal out during the amplifier setup.

5012 SoundShaker Amplifier (Front)

5012 SoundShaker Amplifier (Rear)

5

6a

6b

6c

6d

7a

7b

7c

7d

3120

Lo

ng

Cab

le

5465

Po

wer

Su

pp

ly

81-3108 Short Cable

81-3108 Short Cable

81-3108 Short Cable

81-3108 Short Cable

*SoundShakers are sold seperately.

Page 4

COMMONLY ASKED QUESTIONSBelow is a list of commonly asked questions. If you have any trouble with your SoundShaker please refer to the information below.

Q. DOES THE ORDER IN WHICH I CONNECT MY SOUNDSHAKERS MATTER?A. No, the order in which your SoundShakers are connected to the long cable will not matter.

The signal runs to all outputs when powered.

Q. MY SOUNDSHAKER SYSTEM DOES NOT APPEAR TO BE WORKING.A. Check and make sure all connections and power supplies are secured. Make sure your

transmitter, amplifier, receiver, and subwoofer are all powered up.

Q. IS SOUNDSHAKER COMPATIBLE WITH OTHER WIRELESS AUDIO SYSTEMS?A. SoundShaker is compatible with any audio system that provides an RCA output to connect

SoundShaker to.

Q. I’VE SYNC’D MY AMP BUT DON’T FEEL ANY VIBRATIONS.A. When syncing your amp be sure to check that an audio signal is being sent out. Your amplifier

will not sync without a signal currently running. Refer to the illustration on the next page to learn how to sync up your amplifier.

Page 5

SOUNDSHAKER WIRELESS SYNCINGPlease follow each to step to ensure that your equipment syncs correctly.

Make sure Wireless Switch is set to . MAKE SURE YOU HAVE A MOVIE OR MUSIC PLAYING, press and hold Code Button for a minimum of 3 seconds to begin syncing process. When light blinks rapidly proceed to step 2.

Press and hold Code Button for a minimum of 3 seconds until light blinks rapidly. Red light will turn solid when pairing is completed. (Both units should have solid red lights when paired.)

STEP 2. HOLD TRANSMITTER CODE BUTTON TO COMPLETE SYNC WITH AMP

POWER X-OVER WIRELESS CODE

OFF

1

2

34

56

7

8

9

10 50HZ

55HZ

60HZ

65HZ

70HZ75HZ

80HZ

85HZ

90HZ

95HZ

100HZ

STEP 1. HOLD AMPLIFIER CODE BUTTON TO BEGIN SYNC

PLEASE NOTE: YOUR SOUNDSHAKER SHOULD ALREADY BE SYNC’D WITH YOUR SOUNDSHAKER AMPLIFIER.

1

OFF-ON CODE

2

5012 Amplifier

5024 Transmitter