installation install valve trim 3 adjust hot limit stop ... · pdf fileadjust hot limit stop...
TRANSCRIPT
Recommended Tools
Flat Blade Screwdriver
Adjustable WrenchChannel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
Teflon Tape
FINISHED WALL
4"
TOP OF TUB RIM
BOTTOM OF TUB
74" FOR HEADCLEARANCE
4-1/4" REF.
1-5/8" TO 3"
18" OPTIONAL
4-7/8" REF.
1/2" NPT
1/2" COPPERFOR SLIP-ON
SPOUT
7-1/2"
1-1/2"
6" REF. OPTIONAL TO FINISHEDFLOOR USUALLYBETWEEN 65'' AND 78'
"SEE ILLUSTRATION "
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS (For reference only)
To assure proper positioning in relation to wall, note roughing-in dimensions.
PRESSURE BALANCING BATHAND SHOWER TRIM KITS
COPELAND
SERVICE5
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inletsand MANIFOLD (5). Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off"to "on". Do not apply excessive force.Clogged CARTRIDGE (4) inlets may cause reduced flow in "fullon" hot or cold. To clean inlets, first turn off water supply, then:
5
4
3
2
1
6
PRESSURE BALANCEBATH/SHOWER
MODEL NUMBER
M962606-YYY0ASHOWER ARM
AND FLANGE
M950234-YYY0ADIVERTER SPOUT (SLIP-ON)
M953579-YYY0ASHOWER HEAD
InstallationInstructions
T005.5XX
T005.5XX
COPELAND
THREADED INLETS (STOPS)
INLETS1/2" NPT
5-7/8"
INLETS 1/2" NPTOUTLETS1/2" NPT
OUTLETS1/2" NPT
3-3/8"
3-3/8"
3-3/8"
THREADED INLETS
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
4-1/16"
5-7/8"
INLETS4-1/16"
4-1/16"
INLETS1/2" NOM.COPPERSWEAT
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
2"
SWEATINLETS
SWEATINLETS (STOPS)
INLETS1/2" NOM.COPPERSWEAT
M968636 Rev 1.1
M968636 Rev 1.1 M968636 Rev 1.1 M968636 Rev 1.1
7
8
"B" "B"
3 ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amountof hot water allowed to mix with the cold, the HOT LIMITSAFETY STOP reduces risk of accidental scalding. To setthe maximum hot water temperature of your faucets, allyou need to do is adjust the setting on the HOT LIMITSAFETY STOP.
Use a flat blade screwdriver or your fingers to pullup and rotate red HOT LIMIT SAFETY STOP (1).Follow Step "A" or "B" to adjust min./max. dischargetemperature. "0" being the hottest to "7" the coldesttemperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RINGFORWARD AND ROTATECOUNTER-CLOCKWISE
ONE CLICK
PRY RED RINGFORWARD AND
ROTATE CLOCKWISE
"A"
"A"ADJUSTMENT WHENWATER IS TOO HOT ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOTLIMIT SAFETY STOP
TEMPERATURESETTING
NUMBERS
1
0 1 2 3 4
5 6
12.5MM HEXWRENCH
4 HANDLE INSTALLATION
3
1 INSTALL VALVE TRIM
1
Figure 1.
Figure 2. Figure 3.
3
5
6
4
2
1
Figure 1. Remove plaster guard from valve. Push CAP (1)over VALVE CARTRIDGE (2) until seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1)and attach with LONG SCREWS (4). Mount ESCUTCHEONSUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORTSCREWS (6).
Figure 3. Align PINS (7) on back side of ESCUTCHEON (8)with the FOUR HOLES (9) in ESCUTCHEON SUPPORT (5)and press ESCUTCHEON (8) flush against finished wall.
PLSTERGUARD
9
5
PIPEPLUG
PIPECAP
1
4
3
2SHR.ELBOW
TUB FILLER NIPPLE
1-1/2" REF.
Remove pipe cap and plug from shower and tubrough piping.
Slip TUB SPOUT (1) onto tub nipple and tighten with4mm Hex Wrench.CAUTION: Protect finish on TUB SPOUT wheninstalling.
Install SHOWER ESCUTCHEON (2) onto SHOWERARM (3). Apply sealant or Teflon tape to threads on both ends of SHOWER ARM (3) and thread longerleg of SHOWER ARM (3) into shower elbow.
Thread SHOWER HEAD (4) onto SHOWER ARM (3).
2 INSTALL TUB SPOUT, SHOWER HEAD,SHOWER ARM WITH FLANGE
CAUTION: Protect finish on SHOWER HEAD andARM when installing.
CAUTION: Protect finish on SHOWERHEAD and TUB SPOUT when installing.
Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)and tightening SET SCREW (3) from below with 2.5mmHex Wrench supplied. 2
M907050-YYY0ACAP
M962605-YYY0AESCUTCHEON AND SEAL
M962607-YYY0AHANDLE
M962427-0070AESCUTCHEON HOLDER
HOT LINE FOR HELPFor toll-free information and answers to your questions, call:
1 (800) 442-1902Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names l isted herein are trademarks of American Standard Inc.© American Standard Inc. 2007
IN MEXICO 01-800-839-12-00
CHROMESATIN NICKELBLACKENED BRONZE
002295068
Replace the "YYY" withappropriate finish code
4MM HEXWRENCH
Thank you for selecting American-Standard...the benchmarkof fine quality for over 100 years.
To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR ACLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Recommended Tools
Flat Blade Screwdriver
Adjustable WrenchChannel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
Teflon Tape
FINISHED WALL
4"
TOP OF TUB RIM
BOTTOM OF TUB
74" FOR HEADCLEARANCE
4-1/4" REF.
1-5/8" TO 3"
18" OPTIONAL
4-7/8" REF.
1/2" NPT
1/2" COPPERFOR SLIP-ON
SPOUT
7-1/2"
1-1/2"
6" REF. OPTIONAL TO FINISHEDFLOOR USUALLYBETWEEN 65'' AND 78'
"SEE ILLUSTRATION "
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS (For reference only)
To assure proper positioning in relation to wall, note roughing-in dimensions.
PRESSURE BALANCING BATHAND SHOWER TRIM KITS
COPELAND
SERVICE5
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inletsand MANIFOLD (5). Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off"to "on". Do not apply excessive force.Clogged CARTRIDGE (4) inlets may cause reduced flow in "fullon" hot or cold. To clean inlets, first turn off water supply, then:
5
4
3
2
1
6
PRESSURE BALANCEBATH/SHOWER
MODEL NUMBER
M962606-YYY0ASHOWER ARM
AND FLANGE
M950234-YYY0ADIVERTER SPOUT (SLIP-ON)
M953579-YYY0ASHOWER HEAD
InstallationInstructions
T005.5XX
T005.5XX
COPELAND
THREADED INLETS (STOPS)
INLETS1/2" NPT
5-7/8"
INLETS 1/2" NPTOUTLETS1/2" NPT
OUTLETS1/2" NPT
3-3/8"
3-3/8"
3-3/8"
THREADED INLETS
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
4-1/16"
5-7/8"
INLETS4-1/16"
4-1/16"
INLETS1/2" NOM.COPPERSWEAT
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
2"
SWEATINLETS
SWEATINLETS (STOPS)
INLETS1/2" NOM.COPPERSWEAT
M968636 Rev 1.1
M968636 Rev 1.1 M968636 Rev 1.1 M968636 Rev 1.1
7
8
"B" "B"
3 ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amountof hot water allowed to mix with the cold, the HOT LIMITSAFETY STOP reduces risk of accidental scalding. To setthe maximum hot water temperature of your faucets, allyou need to do is adjust the setting on the HOT LIMITSAFETY STOP.
Use a flat blade screwdriver or your fingers to pullup and rotate red HOT LIMIT SAFETY STOP (1).Follow Step "A" or "B" to adjust min./max. dischargetemperature. "0" being the hottest to "7" the coldesttemperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RINGFORWARD AND ROTATECOUNTER-CLOCKWISE
ONE CLICK
PRY RED RINGFORWARD AND
ROTATE CLOCKWISE
"A"
"A"ADJUSTMENT WHENWATER IS TOO HOT ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOTLIMIT SAFETY STOP
TEMPERATURESETTING
NUMBERS
1
0 1 2 3 4
5 6
12.5MM HEXWRENCH
4 HANDLE INSTALLATION
3
1 INSTALL VALVE TRIM
1
Figure 1.
Figure 2. Figure 3.
3
5
6
4
2
1
Figure 1. Remove plaster guard from valve. Push CAP (1)over VALVE CARTRIDGE (2) until seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1)and attach with LONG SCREWS (4). Mount ESCUTCHEONSUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORTSCREWS (6).
Figure 3. Align PINS (7) on back side of ESCUTCHEON (8)with the FOUR HOLES (9) in ESCUTCHEON SUPPORT (5)and press ESCUTCHEON (8) flush against finished wall.
PLSTERGUARD
9
5
PIPEPLUG
PIPECAP
1
4
3
2SHR.ELBOW
TUB FILLER NIPPLE
1-1/2" REF.
Remove pipe cap and plug from shower and tubrough piping.
Slip TUB SPOUT (1) onto tub nipple and tighten with4mm Hex Wrench.CAUTION: Protect finish on TUB SPOUT wheninstalling.
Install SHOWER ESCUTCHEON (2) onto SHOWERARM (3). Apply sealant or Teflon tape to threads on both ends of SHOWER ARM (3) and thread longerleg of SHOWER ARM (3) into shower elbow.
Thread SHOWER HEAD (4) onto SHOWER ARM (3).
2 INSTALL TUB SPOUT, SHOWER HEAD,SHOWER ARM WITH FLANGE
CAUTION: Protect finish on SHOWER HEAD andARM when installing.
CAUTION: Protect finish on SHOWERHEAD and TUB SPOUT when installing.
Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)and tightening SET SCREW (3) from below with 2.5mmHex Wrench supplied. 2
M907050-YYY0ACAP
M962605-YYY0AESCUTCHEON AND SEAL
M962607-YYY0AHANDLE
M962427-0070AESCUTCHEON HOLDER
HOT LINE FOR HELPFor toll-free information and answers to your questions, call:
1 (800) 442-1902Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names l isted herein are trademarks of American Standard Inc.© American Standard Inc. 2007
IN MEXICO 01-800-839-12-00
CHROMESATIN NICKELBLACKENED BRONZE
002295068
Replace the "YYY" withappropriate finish code
4MM HEXWRENCH
Thank you for selecting American-Standard...the benchmarkof fine quality for over 100 years.
To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR ACLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Recommended Tools
Flat Blade Screwdriver
Adjustable WrenchChannel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
Teflon Tape
FINISHED WALL
4"
TOP OF TUB RIM
BOTTOM OF TUB
74" FOR HEADCLEARANCE
4-1/4" REF.
1-5/8" TO 3"
18" OPTIONAL
4-7/8" REF.
1/2" NPT
1/2" COPPERFOR SLIP-ON
SPOUT
7-1/2"
1-1/2"
6" REF. OPTIONAL TO FINISHEDFLOOR USUALLYBETWEEN 65'' AND 78'
"SEE ILLUSTRATION "
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS (For reference only)
To assure proper positioning in relation to wall, note roughing-in dimensions.
PRESSURE BALANCING BATHAND SHOWER TRIM KITS
COPELAND
SERVICE5
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inletsand MANIFOLD (5). Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off"to "on". Do not apply excessive force.Clogged CARTRIDGE (4) inlets may cause reduced flow in "fullon" hot or cold. To clean inlets, first turn off water supply, then:
5
4
3
2
1
6
PRESSURE BALANCEBATH/SHOWER
MODEL NUMBER
M962606-YYY0ASHOWER ARM
AND FLANGE
M950234-YYY0ADIVERTER SPOUT (SLIP-ON)
M953579-YYY0ASHOWER HEAD
InstallationInstructions
T005.5XX
T005.5XX
COPELAND
THREADED INLETS (STOPS)
INLETS1/2" NPT
5-7/8"
INLETS 1/2" NPTOUTLETS1/2" NPT
OUTLETS1/2" NPT
3-3/8"
3-3/8"
3-3/8"
THREADED INLETS
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
4-1/16"
5-7/8"
INLETS4-1/16"
4-1/16"
INLETS1/2" NOM.COPPERSWEAT
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
2"
SWEATINLETS
SWEATINLETS (STOPS)
INLETS1/2" NOM.COPPERSWEAT
M968636 Rev 1.1
M968636 Rev 1.1 M968636 Rev 1.1 M968636 Rev 1.1
7
8
"B" "B"
3 ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amountof hot water allowed to mix with the cold, the HOT LIMITSAFETY STOP reduces risk of accidental scalding. To setthe maximum hot water temperature of your faucets, allyou need to do is adjust the setting on the HOT LIMITSAFETY STOP.
Use a flat blade screwdriver or your fingers to pullup and rotate red HOT LIMIT SAFETY STOP (1).Follow Step "A" or "B" to adjust min./max. dischargetemperature. "0" being the hottest to "7" the coldesttemperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RINGFORWARD AND ROTATECOUNTER-CLOCKWISE
ONE CLICK
PRY RED RINGFORWARD AND
ROTATE CLOCKWISE
"A"
"A"ADJUSTMENT WHENWATER IS TOO HOT ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOTLIMIT SAFETY STOP
TEMPERATURESETTING
NUMBERS
1
0 1 2 3 4
5 6
12.5MM HEXWRENCH
4 HANDLE INSTALLATION
3
1 INSTALL VALVE TRIM
1
Figure 1.
Figure 2. Figure 3.
3
5
6
4
2
1
Figure 1. Remove plaster guard from valve. Push CAP (1)over VALVE CARTRIDGE (2) until seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1)and attach with LONG SCREWS (4). Mount ESCUTCHEONSUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORTSCREWS (6).
Figure 3. Align PINS (7) on back side of ESCUTCHEON (8)with the FOUR HOLES (9) in ESCUTCHEON SUPPORT (5)and press ESCUTCHEON (8) flush against finished wall.
PLSTERGUARD
9
5
PIPEPLUG
PIPECAP
1
4
3
2SHR.ELBOW
TUB FILLER NIPPLE
1-1/2" REF.
Remove pipe cap and plug from shower and tubrough piping.
Slip TUB SPOUT (1) onto tub nipple and tighten with4mm Hex Wrench.CAUTION: Protect finish on TUB SPOUT wheninstalling.
Install SHOWER ESCUTCHEON (2) onto SHOWERARM (3). Apply sealant or Teflon tape to threads on both ends of SHOWER ARM (3) and thread longerleg of SHOWER ARM (3) into shower elbow.
Thread SHOWER HEAD (4) onto SHOWER ARM (3).
2 INSTALL TUB SPOUT, SHOWER HEAD,SHOWER ARM WITH FLANGE
CAUTION: Protect finish on SHOWER HEAD andARM when installing.
CAUTION: Protect finish on SHOWERHEAD and TUB SPOUT when installing.
Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)and tightening SET SCREW (3) from below with 2.5mmHex Wrench supplied. 2
M907050-YYY0ACAP
M962605-YYY0AESCUTCHEON AND SEAL
M962607-YYY0AHANDLE
M962427-0070AESCUTCHEON HOLDER
HOT LINE FOR HELPFor toll-free information and answers to your questions, call:
1 (800) 442-1902Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names l isted herein are trademarks of American Standard Inc.© American Standard Inc. 2007
IN MEXICO 01-800-839-12-00
CHROMESATIN NICKELBLACKENED BRONZE
002295068
Replace the "YYY" withappropriate finish code
4MM HEXWRENCH
Thank you for selecting American-Standard...the benchmarkof fine quality for over 100 years.
To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR ACLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Recommended Tools
Flat Blade Screwdriver
Adjustable WrenchChannel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
Teflon Tape
FINISHED WALL
4"
TOP OF TUB RIM
BOTTOM OF TUB
74" FOR HEADCLEARANCE
4-1/4" REF.
1-5/8" TO 3"
18" OPTIONAL
4-7/8" REF.
1/2" NPT
1/2" COPPERFOR SLIP-ON
SPOUT
7-1/2"
1-1/2"
6" REF. OPTIONAL TO FINISHEDFLOOR USUALLYBETWEEN 65'' AND 78'
"SEE ILLUSTRATION "
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS (For reference only)
To assure proper positioning in relation to wall, note roughing-in dimensions.
PRESSURE BALANCING BATHAND SHOWER TRIM KITS
COPELAND
SERVICE5
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inletsand MANIFOLD (5). Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off"to "on". Do not apply excessive force.Clogged CARTRIDGE (4) inlets may cause reduced flow in "fullon" hot or cold. To clean inlets, first turn off water supply, then:
5
4
3
2
1
6
PRESSURE BALANCEBATH/SHOWER
MODEL NUMBER
M962606-YYY0ASHOWER ARM
AND FLANGE
M950234-YYY0ADIVERTER SPOUT (SLIP-ON)
M953579-YYY0ASHOWER HEAD
InstallationInstructions
T005.5XX
T005.5XX
COPELAND
THREADED INLETS (STOPS)
INLETS1/2" NPT
5-7/8"
INLETS 1/2" NPTOUTLETS1/2" NPT
OUTLETS1/2" NPT
3-3/8"
3-3/8"
3-3/8"
THREADED INLETS
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
4-1/16"
5-7/8"
INLETS4-1/16"
4-1/16"
INLETS1/2" NOM.COPPERSWEAT
SHR. 1/2" NOM.COPPER SWEAT
TUB 1/2" NOM.COPPER SWEAT
2"
SWEATINLETS
SWEATINLETS (STOPS)
INLETS1/2" NOM.COPPERSWEAT
M968636 Rev 1.1
M968636 Rev 1.1 M968636 Rev 1.1 M968636 Rev 1.1
7
8
"B" "B"
3 ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amountof hot water allowed to mix with the cold, the HOT LIMITSAFETY STOP reduces risk of accidental scalding. To setthe maximum hot water temperature of your faucets, allyou need to do is adjust the setting on the HOT LIMITSAFETY STOP.
Use a flat blade screwdriver or your fingers to pullup and rotate red HOT LIMIT SAFETY STOP (1).Follow Step "A" or "B" to adjust min./max. dischargetemperature. "0" being the hottest to "7" the coldesttemperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RINGFORWARD AND ROTATECOUNTER-CLOCKWISE
ONE CLICK
PRY RED RINGFORWARD AND
ROTATE CLOCKWISE
"A"
"A"ADJUSTMENT WHENWATER IS TOO HOT ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOTLIMIT SAFETY STOP
TEMPERATURESETTING
NUMBERS
1
0 1 2 3 4
5 6
12.5MM HEXWRENCH
4 HANDLE INSTALLATION
3
1 INSTALL VALVE TRIM
1
Figure 1.
Figure 2. Figure 3.
3
5
6
4
2
1
Figure 1. Remove plaster guard from valve. Push CAP (1)over VALVE CARTRIDGE (2) until seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1)and attach with LONG SCREWS (4). Mount ESCUTCHEONSUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORTSCREWS (6).
Figure 3. Align PINS (7) on back side of ESCUTCHEON (8)with the FOUR HOLES (9) in ESCUTCHEON SUPPORT (5)and press ESCUTCHEON (8) flush against finished wall.
PLSTERGUARD
9
5
PIPEPLUG
PIPECAP
1
4
3
2SHR.ELBOW
TUB FILLER NIPPLE
1-1/2" REF.
Remove pipe cap and plug from shower and tubrough piping.
Slip TUB SPOUT (1) onto tub nipple and tighten with4mm Hex Wrench.CAUTION: Protect finish on TUB SPOUT wheninstalling.
Install SHOWER ESCUTCHEON (2) onto SHOWERARM (3). Apply sealant or Teflon tape to threads on both ends of SHOWER ARM (3) and thread longerleg of SHOWER ARM (3) into shower elbow.
Thread SHOWER HEAD (4) onto SHOWER ARM (3).
2 INSTALL TUB SPOUT, SHOWER HEAD,SHOWER ARM WITH FLANGE
CAUTION: Protect finish on SHOWER HEAD andARM when installing.
CAUTION: Protect finish on SHOWERHEAD and TUB SPOUT when installing.
Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)and tightening SET SCREW (3) from below with 2.5mmHex Wrench supplied. 2
M907050-YYY0ACAP
M962605-YYY0AESCUTCHEON AND SEAL
M962607-YYY0AHANDLE
M962427-0070AESCUTCHEON HOLDER
HOT LINE FOR HELPFor toll-free information and answers to your questions, call:
1 (800) 442-1902Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names l isted herein are trademarks of American Standard Inc.© American Standard Inc. 2007
IN MEXICO 01-800-839-12-00
CHROMESATIN NICKELBLACKENED BRONZE
002295068
Replace the "YYY" withappropriate finish code
4MM HEXWRENCH
Thank you for selecting American-Standard...the benchmarkof fine quality for over 100 years.
To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR ACLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS: