installation instructions - amazon s3 · installation instructions evotech performance recommend...
TRANSCRIPT
Installation Instructions
Installation Instructions
Evotech Performance recommend that brake and clutch leversbe fitted by a fully trained mechanic.
If you chose to fit the any aftermarket brake or clutch leverswithout sufficient training or advise from Evotech Performance
then you do so at your own risk.
Evotech Perfromance accept no responsibility for any incorrect fitment.
Installation Instructions
EVOTECH PERFORMANCEBRAKE AND CLUTCH LEVERS
Instruction Contents
Section 1 - Cable Clutch
Section 2 - Hydraulic Brake and Clutch
Section 3 - Ducati Hydraulic Brake and Clutch
Section 4 - Aprillia Tuono V4/RSV4 2015 Cable Clutch
Section 5 - Coloured adjuster replacement
Section 1
Section 1 - Cable Clutch
1Section 1
Caution
Completely remove security nutfrom underneath firstthen remove the bolt
2Section 1
Caution
Clutch adjuster screw may needto be wound in to allow enough
slack to rotate lever
Rotate lever 180 degreesand unclicp cable
3Section 1
Hook cable into leverand rotate 180 degrees
Caution
When rotating into posistionensure not to damage
micro switches
4Section 1
OEM PART
OEM PART Caution
DO NOT over-tightensecurity nut
5Section 1
Caution
Check range of movementbefore riding
Adjust lever reach to riderspecific setting
Section 2
Section 2 - Hydraulic Brake and Clutch
1Section 2
Caution
Completely remove security nutfrom underneath firstthen remove the bolt
2Section 2
Caution
Remove lever ensuring notto damage rubber seal
3Section 2
OEM PART
OEM PARTCaution
DO NOT over-tightensecurity nut
Caution
When placing into posistionensure not to damage
micro switches
4Section 2
Caution
Check range of movementbefore riding
Adjust lever reach to riderspecific setting
Section 3
Section 3 - Ducati Hydraulic Brake and Clutch
1Section 3
Caution
Completely remove security nutfrom underneath firstthen remove the bolt
2Section 3
Caution
Remove lever ensuring notto damage rubber seal
3Section 3
Caution
Remove brass bush fromoriginal lever and transfer
into new lever
Caution
Remove activation pinfrom original lever andtransfer into new one
4Section 3
Caution
Replace brass bush fromoriginal lever into new lever
Caution
Replace activation pinfrom original lever
into new one
5Section 3
OEM PART
OEM PARTCaution
DO NOT over-tightensecurity nut
Caution
When placing into posistionensure not to damage
micro switches
6Section 3
Caution
Check range of movementbefore riding
Adjust lever reach to riderspecific setting
Section 4
Section 4 - Aprilia Tuono V4 2015and RSV4 2015 Clutch
1Section 4
Caution
Completely remove security nutfrom underneath firstthen remove the bolt
2Section 4
Caution
Clutch adjuster screw may needto be wound in to allow enough
slack to rotate lever
Rotate lever 180 degreesand unclicp cable
3Section 4
Remove secondary cable adjusterfrom inside lever
4Section 4
Hook cable into leverand rotate 180 degrees
Caution
When rotating into posistionensure not to damage
micro switches
5Section 4
OEM PART
OEM PART Caution
DO NOT over-tightensecurity nut
6Section 4
Caution
Check range of movementbefore riding
Adjust lever reach to riderspecific setting
Section 5
Section 5 - Coloured Adjuster Replacement
1Section 5
Caution
Completely remove security nutfrom underneath
2Section 5
3Section 5
Caution
Sprung Ball Bearing
4Section 5
Caution
Sprung Ball Bearing
5Section 5
ALIGN FLATEDGES
ENSURE NOTCHES ARE ALIGNED WHEN RE-FITTING
6Section 5
Caution
Ensure ball bearing islocated correctly.
Apply small amount of grease
7Section 5
Caution
Ensure ball bearing islocated correctly.
Apply small amount of grease
8Section 5
9Section 5
Caution
DO NOT over-tightensecurity nut
www.evotech-performance.com