installation instructions overflow drain and fill spout1. measure the distance from the center of...

Jason International, Inc. • 501.771.4477 of 5 Customer Service : 800.255.5766 Copyright © 2010 Jason International.

“to be removed for use by the occupant.”

INTRODUCTIONJason’s Overflow Drain and Fill Spout fits all Jason baths. The fill spout is integrated with the knob and overflow assembly, so there is no need for an additional fill spout.

CONTENTSThe Overflow Drain and Fill Spout assembly includes a plated metal knob, drain, and overflow.

TOOlS & maTERIalS REqUIREDFor safety and ease of installation, Jason recommends the following tools: safety glasses, flashlight, adjustable wrench, screwdriver, tape measure, and PTFE plumbers tape. Specific tools and materials for installing this product include the following:

- Measuring tape- Silicon lubricant (supplied)- Sand paper - Flathead screwdriver

INSTallaTIONAll local and state plumbing codes must be observed. It is the responsibility of the installer/owner to determine specific code compliance when installing this product.

1. Measure the distance from the center of the drain hole to the center of the overflow hole. See A in Figure 1.

49-2051-000Date 05/08

INSTALLATION INSTRUCTIONS

Overflow Drain and Fill Spout

Jason International, Inc. 8328 MacArthur Drive

North Little Rock, AR 72118www.jasoninternational.com

Figure 1

4. Check the dimensions by dry mounting the faucet to the bath prior to installation. See A and B in Figure 4.

Figure 2

3. Apply silicon lubricant (included) to the threads to make assembly easier. See Figure 3.

Figure 3

Figure 4

2. Measure the height from the center of the drain hole to the center of the overflow hole. See B in Figure 2.


8. Put the cover in place. Then install the overflow nut and tighten. See Figure 8.

Figure 6

9. Connect with the tee and hand-tighten the slipnuts. Align the shoe and overflow and tighten firmley. See Figure 9.

CAUTION: Do not constrain the cable. This may result in loss of plunger travel.

Figure 7

INSTallaTION INSTRUCTIONS (cont.)

6. Place the gasket on the overflow head in the correct orientation. See Figure 6. Note: Check the outside of the bath for roughness and sand to make smooth.

7. Apply silicon lubricant (supplied) to the outside surface of the rubber washer and inside mating recess. Install the faucet into the overflow housing as shown in Figure 7.

Figure 5

5. Mount the drain to the bath with the supplied drain screw. See Figure 5. Notes: a) Check the outside of the bath for roughness: sand as needed. b) Install the gasket with the rounded side up. c) Use sealant to install the strainer.

Figure 8

10. Place the washer on the shaft. Then place the handle onto the shaft in the orientation shown in Figure 10.

Figure 9

Figure 10

11. Press the handle firmly against the washer and tighten the setscrew. See Figure 11. Note: Ensure that the handle remains parallel to the housing while tightening.

Figure 11

12. Use a flat-head screwdriver to adjust the pop-up to a minimum 1/2” opening. Rotate the handle approximately 1/8” turn to operate.

Figure 12


INSTallaTION INSTRUCTIONS (cont.)

PaRTS

alternative Connection

Item # Description1 Gasket2 Seal3 Overflow Nut4 Cover5 Washer Spacer6 Brass Handle7 Handle Screw8 Stream Former Kit9 Outlet Housing10 Screw (2 each)11 Plunger12 O-Ring13 Hex Nut14 Screw15 Drain Screw16 Strainer17 Gasket18 Standard Tee (Includes (2) Compression

Nuts and Washers)19 Chicago Code Tee (Includes (2) Com-

pression Nuts and Washers) (Not sup-plied with Unit)

20 Check Valve Kit


Technical DaTa


Jason InternatIonal, Inc.8328 MacArthur Drive • North Little Rock • Arkansas • 72118

www.jasoninternational.com

TroubleshooTing guiDe

Problem SolutionPlunger is not holding water. - Check that the strainer flange is level.

- Check the setscrew adjustment.- Check the O-ring around the plunger.

Leaks appear between strainer and bath. - Check that the sealant is applied completely.- Check that the strainer flange is level with the bath surface.- Check tightness of drain screw.

Water closes plunger when draining. - Adjust plunger to maximum opening of 1/2”.- Secure the cable to the overflow pipe.- Wrong size drain. Cable is too long - exchange.

Handle does not rotate the full 1/8 turn. - Check cable to make sure it is installed freely.- Check cable to see if it appears to be the correct length. - The cable should not have a lot of extra length. - The cable should not appear to be too tight.

Water flow is restricted or of poor quality. - Check outside of screen assembly for any obstructions.- Remove the screen assembly. Clean the screen assembly if

required. Run water through the unit. Reinstall the screen assembly.

Water leaks from aruond the cover when filling the bath.

- Tighten the screw that holds the screen assembly housing.- Remove the housing and check the seal for any damage. Reinstall

the housing.

installation instructions overflow drain and fill spout1. measure the distance from the center of...

Documents