installation overthe range instructions microwave oven · 2017-10-20 · to allow dee movement of...
TRANSCRIPT
InstallationInstructions
Overthe RangeMicrowave Oven
I Questions? Call 1-800-944-9044(us)1-800-668-4606(Canada) or VisitoL,,-W_bsiteat: http://www.frigidaire.com IBEFORE YOU BEGINRead these instructions completely and carefully.
• IMPORTANT - Savetheseinstructions for local inspector's use.
• IMPORTANT - Observeallgoverning codes and ordinances.
• Note to Installer - Be stH'eto leave theseinstructions with the Consumer.
• Note to Consumer - Keet) theseinstructions for future reference.
• Skill level Installation of this appliance requiresbasic mechanical and electrical skills.
• Proper installation is tile responsibility of the installer.
• Product failure due to improper installation is notcovered under tile Warranty.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
Installation Instructions
CONTENTS
General information
Important Safety Instructions ........................ 3
Electrical Requirements .......................................... 3
Hood Exhaust .................................................. 4, 5
Damage - Shipment/Installation .............................. 6
Parts Induded. ......................................... 6
Tools You Will Need ............................................... 7
Mounting Space ...................................................... 7
Step-by-step installation guide
Placement of Mounting Plate ............................ 8-10
Removing the Mountirlg Plate ...................... 8
Finding tile Wall Studs .................................. 8
Determining Wall Plate Location .................. 9
Aligning the Wall Plate.. .............................. 10
Installation Types. ............................................. 11-22
[]Outside Top ............................Exhaust 12-14
Attach Mounting Plate to Wall ............ 12
Preparation of Top Cabinet ................ 13
Checking for Proper DamperOperation ............................................ 13
Mount the Microwave Oven ......... 13, 14
Adjust flae Exhaust Adaptor - ............. 14
Connecting Ductwork .......................... 14
[]Outside Back Exhaust 15-18
Preparing Real" Wall forOutside Back Exhaust .......................... 15
Remove Exhaust Adaptor .... .................. 15
Attach Mounting Plate to Wall .......... 16
Preparation of Top Cabinet .............. 16
Adapting Microwave Blowerfor OutsMe Back Exhaust ................ 16, 17
Mount the Microwave Oven .............. 18
[] Recilvulating ........................................ 19-22
Attach Mourning Plate m Wall ............ 19
Preparation of Top Cabinet ................ 19
Check Microwave Assembly ................ 20
Adapting Microwave Blowerfor Recirculation .......................... 20, 21
Mount the Microwave Oven .......... 21, 22
Installing tile Charcoal Filter .............. 22
Before You Use Your Microwave .......................... 23
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
This product requires a three-prong grounded outlet.The installer nmst perform a ground continuity checkon the power outlet box before beginning theinstallation to insure that the outlet box is properlygrounded. If not properly grounded, or if the outletbox does not meet electrical requirements noted(under ELECTRICAL REQUIREMENTS), a qualifiedelectrician should be employed to correct anydeficiencies.
CAUTION: For personalsafety, remove house fuseor open circuit breakerbefore beginninginstallation to avoid severe
or fatal shock injury.
CAUTION: For personal safety, the mounting surfacemust be capable of supporting the cabinet load, inaddition to the added weight of this 63-85 pound(28.5-38.5 kg) product, plus additional oven loads ofup to 50 pounds (22.7 kg) or a total weight of113-135 pounds (51.3-61.2 kg).
CAUTION: For personal safety, this product cannotbe installed in cabinet arrangements such as an island ora peninsula. It must be mounted to BOTH a top cabinetAND a wall.
NOTE: For easier installation and personal safety, it isrecommended that two people install this product.
IMPORTANT - PLEASE READ CAREFULLY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BEPROPERLY GROUNDED TO AVOID SEVERE ORFATAL SHOCK.
The power cord of thisappliance is equipped with athree-prong (grounding)plug which mates with astandard three-prong(grounding) wall receptacleto minimize the possibilityof electric shock hazard
from this appliance.
Ensurepropergroundexistsbeforeuse
You should have the wall receptacle and circuit checkedby a qualified electrician to make sure the receptacle isproperly grounded.
Where a standard two-prong wall receptacle isencountered, it is very important to have it replacedwith a properly grounded three-prong wall receptacle,installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,DEFORM OR REMOVE ANY OF THE PRONGSFROM THE POWER CORD. DO NOT USE WITHAN EXTENSION CORD.
ELECTRICALREQUIREMENTSProduct rating is 120 volts AC, 60 Hertz, 15 amps and
1.6 kilowatts. This product must be connected to a
supply circuit of the proper voltage and fl'equency.Wire size must conform to the requirements of theNational Electrical Code or the prevailing local
code for this kilowatt rating. The power supply
cord and plug should be brought to a separate15- to 20- ampere branch circuit single groundedoutlet. The outlet box should be located in thecabinet above the microwave oven. The outlet box
and supply circuit should be installed by a qualifiedelectrician and conform to the National Electrical
Code or the prevailing local code.
3
Installation Instructions
HOOD EXHAUSTNOTE: Read these next two pages only if you plan to vent your exhaust to the
outside. If you plan to recirculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)The following chart describes an example of one possibleductwork installation.
DUCT PIECES
_m
RoofCap
12Ft,(3,6m)StraightDuct(6"/15,2cmRound)
EQUIVALENT NUMBERLENGTH x USED
Rectangular-to-RoundTransitionAdaptor*
24Ft,(7,3m) x (1)
12Ft,(3,6m) x (1)
E
5 Ft, (1,5 m) x
Equivalent lengths of duct pieces are based on actual tests andreflect requirements for good venting performance with any vent hood,
(1)
Total Length =
EQUIVALENTLENGTH
24Ft,(7,3m)
12Ft,(3,6m)
5Ft, (1,5m)
41 Ft. (12.5 m)
* IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper
will have to be cut to fit, using the tin snips, in order to allow free movement of the damper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)The following chart describes an example of one possibleductwork installation.
DUCT PIECES
%
EQUIVALENT NUMBER EQUIVALENTLENGTH* x USED = LENGTH
Wall Cap 40 Ft, (12,2 m) x (1) 40 Ft, (12,2 m)
3 Ft,StraightDuct31/4"x 10'78,2x 25,4cmRectangular)
90° Elbow
3 Ft,(0,9m)
10 Ft, (3 m)
(1)
(2)
3 Ft,(0,9m)
20Ft, (3m)
Equivalent lengths of duct pieces are based on actual tests andreflect requirements for good venting performance with any vent hood,
Total Length = 63 Ft. (19.2 m)
NOTE: For back exhaust, care shouM be taken to align exhaust with space between studs, oi" wall shouM be prepared
at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.
4
Installation Instructions
NOTE: If you need to install ducts, note that the totalduct length of 31/4" x 10" (8.2 x 25.4 cm) rectangular or6" (15.2 cm) diameter round duct should not exceed
120 equivalent feet (36.5 m).
Outside ventilation requires a HOOD EXHAUST DUCT.Read the following carefully.
NOTE: It is important that venting be installed usingthe most direct route and with as few elbows as possible.This ensures cleat" venting of exhaust and helps preventblockages. Also, make sure dampers swing freely andnothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate witha standard 31/4" x 10" (8.2 x 25.4 cm) rectangular duct.
If a round duct is required, a rectangular-to-roundtransition adaptor nmst be used. Do not use less thana 6" (15.2 em) diameter duct.
Maximum duct length:For satisfactory air movement, the total duct length of3l/4" x 10" (8.2 x 25.4 cm) rectangular or 6" (15.2 cm)
diameter round duct should not exceed 120 equivalentfeet (36.5 m).
Elbows, transitions, wall and roof caps,etc., present additional resistance to airflow and are
equivalent to a section of straight duct which is longerthan their actual physical size. When calculating the total
duct length, add the equivalent lengths of all transitions
and adaptors plus the length of all straight duct sections.The chart below shows you how to calculate total
equivalent ductwork length using the al)t)roximate feetof equivalent length of some typical ducts.
DUCT PIECES
@
J
Rectangular-to-RoundTransitionAdaptor*
Wall Cap
90° Elbow
45° Elbow
90° Elbow
45° Elbow
RoofCap
StraightDuct6" (15,2cm)Roundor 374"x 10"(8,2x 25,4cm)Rectangular
EQUIVALENT NUMBERLENGTH x USED
5 Ft, (1,5 m)
40Ft, (12,2m)
10 Ft,(3m)
5 Ft, (1,5 m)
25 Ft, (7,6 m)
5 Ft, (1,5 m)
24 Ft,(7,3m)
I Ft,(0,3m)
x ()
x ()
x ()
x ()
x ()
x ()
x ()
x ()
Total Ductwork
EQUIVALENTLENGTH
Ft, or m
Ft, or m
Ft, or m
Ft, or m
Ft, or m
Ft, or m
Ft, or m
Ft, or m
Ft. or m
* IMPORTANT: If a rectangular to round transition
adaptor is used, the bottom corners of tbe dan]per
will bave to be cut to fit, using tbe tit] snips, in order
to allow Dee movement of tbe dan]per.
5
Equivalent lengths of duct pieces are based on actual tests
and reflect requirements for good venting performance wit[]
any vent hood.
Installation Instructions
DAMAGEmSHIPMENT/INSTALLATION
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for repair
or replacement.
• If the unit is damaged by the customer, repair orreplacement is the responsibility of tile customer.
• If the unit is damaged by the installer (if otherthan the customer), repair or replacement nmst
be made by arrangement between customerand installer.
PARTS INCLUDED
HARDWARE PACKET
PART QUANTITY
Wood Screws 2(1/;,x 2")
Toggle Bolts (and 4
wing nuts) (Sk6"x 3")
Self-Aligning Machine 3Screws (1/4"-28x 31/4'')
Nylon Grommet 2(for metal cabinets)
Power Cord Strap 1(plastic)
You will find the installation hardware contained in
a packet with the unit. Check to make sure you haveall these parts.
NOTE: Some extra parts are included.
PARTS INCLUDED (coNT.)
ADDITIONAL PARTS
PART
TOP CABINETTEMPLATE
REARWALL
TEMPLATE
TopCabinetTemplate
RearWall
Template
InstallationInstructions
SeparatelyPackedGreaseFilters
QUANTITY
1
6
Installation Instructions
TOOLS YOU WILL NEED
# 1 Phillipsscrewdriver
Tinsnips(forcuttingdamper,if required)
Gloves
Safetygoggles
Pencil
Scissors(to cut template,if necessary)
Saw (saber,holeor keyhole)
Ruleror tape measureand
t edge
Electricdrill with skd',Y2"and%"drill bits
Studfinder or Hammer(optional)
Level
Carpentersquare(optional)
Fillerblocksor scrapwoodpieces,if neededFortop cabinetspacing(usedon recessedbottomcabinet installationsonly)
Duct and masking tape
MOUNTING SPACE
66" (167.6cm)or Morefromthe Floorto the
Topof theMicrowave
BottomEdgeofCabinetNeedsto
30" (76.2cm)or Morefrom theCookingSurface
I
Backsplash
NOTES:
• The space between the cabinets must be30" (76.2 cm)wide and flee of obstructions.
• If you are going to vent your microwave ovento the outside, see Hood Exhaust Section for
exhaust duct preparation.
• When installing the microwave oven beneathsmooth, fiat cabinets, be careful to follow the
instructions on the top cabinet template forpower cord clearance.
7
Installation Instructions
PLACEMENT OF THE MOUNTING PLATE
I-_ REMOVING THE MICROWAVEOVEN FROM THE CARTON/REMOVING THE MOUNTINGPLATE
[]Remove the installation instructions, filters, glass
tray and the small hardware bag. Do not removethe Styrofoam protecting the fl'ont of the oven.
[]Fold back all 4 carton flaps fully against cartonsides. Then carefully roll the oven and carton overonto the top side. The oven should be resting inthe Styrofoam.
[Pull the carton up and off the oven.
[]Remove and properly discard plastic bags.
Screws----__MountingPlate
Ti
[]Remove the screws from the mounting plate.This plate will be used as the rear wall templateand for mounting. Reinstall the screws into theholes where they were removed.
I-_ FINDING THE WALL STUDS
]Find the studs, using one of the followingmethods:
A. Stud finder - a magnetic device whichlocates nails.
OR
B. Use a hammer to tap lightly across themounting surface to find a solid sound.This will indicate a stud location.
[] After locating the stud(s), find the center byprobing the wall with a small nail to find the edgesof the stud. Then place a mark halfway betweenthe edges. The center of any adjacent studs shouldbe 16" (40.6 cm) or 24" (61 cm) fi'oln this mark.
[]Draw a line down the center of the studs.
THE MICROWAVE MUST BE CONNECTED TOAT LEAST ONE WALL STUD.
8
Installation Instructions
I-_ DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate positionmbeneath flat bottomcabinet
Plate positionmbeneath framed recessedcabinet bottom
Mounting Plate Tabsg the Cabinet Bottom
MountingPlateTabsTouchingthe BackFrame
At least 30" (76.2 cm),up to 36" (91,4 cm)
30" (76.2cm)to Cooktop
Plate position_beneath recessed bottomcabinet with front overhang
MountingPlatewithTabsBelowCabinetBottomthe SameDistanceas the Front
OverhangDepth
30"(76.2 cm)to Cooktop
Your cabinets may have decorative trim that
interferes with the microwave installation. Remove
the decorative trim to install the microwave properly
and to make it level.
THE MICROWAVE MUST BE LEVEL.Use a level to make sure the cabinet bottom is level.
If the cabinets have a fl'ont overhang only, with no
back or side fl'ame, install the mounting plate down
the same distance as the fl'ont overhang depth. Thiswill kee t) the microwave level.
[]Measure the inside depth of the fl'ont overhang.
[]Draw a horizontal line on the back wall an equaldistance below the cabinet bottom as the inside
depth of the fl'ont overhang.
[] For this type of installation with fl'ont overhang only,
align the mounting tabs with this horizontal line, nottouching the cabinet bottom as described in Step D.
9
Installation Instructions
ALIGNING THE WALL PLATE
, I
j_-_ Draw a Verticalj LineonWall I/II fromCenterof [/I
Centerline j TopCabinet I//
Notches j I//
,,................
CAUTION: _ tto avoid cuttil HoleC AreaEsharp edges.
HoleD
_Draw a vertical line on the wall at the center of the
30" (76.2 cm) wide space.
_Use the mounting plate as the template for the rear
wall. Place the mounting plate on the wall, makingsure that the tabs are touching the bottom of thecabinet or the level line drawn in Step C for cabinetswith front overhang. Line up the notch and centerlineon the bottom of the mounting plate to the centerlineon the wall.
_ While holding the mounting plate with one hand,draw circles on the wall at holes A, B, C and D
(see illustration above/actual plate marked withan'ows). Four holes must be used for mounting.
[]
NOTE: If neither C nor D is in a stud, find a studsomewhere in area E and draw a fifth circle to line upwith the stud. It is important to use at least one wood
screw mounted firmly in a stud to support the weightof the microwave.
Set the mounting plate aside.
Drill holes on the circles. If there is a stud, drill a 3A(;"hole for wood screws. For holes that don't line up witha stud, drill a %" hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE ATTHIS TIME.
10
Installation Instructions
I-2-1 INSTALLATION TYPES (Choose A, B or C)
This microwave oven is designed for adaptation tothe following three types of ventilation:
A. Outside Top Exhaust (Vertical Duet)
B. Outside Back Exhaust (Horizontal Duet)
C. Reeirculafing (Non-Vented Ductless)
NOTE: This microwave is shipped assembled for OutsideTop Exhaust (except for non-vented models). Select the
type of ventilation required for your installation and
proceed to that section.
_-_ OUTSIDE TOP EXHAUST(VERTICAL DUCT)
[_ OUTSIDE BACK EXHAUST(HORIZONTAL DUCT)
Adaptorin PlaceforOutsideTopExhaust
AdaptorMust BeMovedto the BackforOutsideBackExhaust
[_ RECIRCULATING(NON-VENTED DUCTLESS)
On models shipped forrecirculating exhaust, adisposable charcoal filteris factory installed to hel t)remove smoke and odors.
On Models shipped foroutside top exhaust or outsideback exhaust, a Charcoal filter
Accessory Kit is required forthe recirculating exhaust.(See your Owner's Manualfor kit number.)
11
Installation Instructions
OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
AI. Attach Motmtirlg Plate to WallA2. Prepare Top Cabinet
A3. Check Damper Operation "[A4. MouIrt Microwave Oven !A5. Adjust Exhaust AdaptorA6. Connect Ductwork
I-_ ATTACH THE MOUNTINGPLATE TO THE WALL
Attach the plate to the wall using toggle bolts.At least one wood screw must be used to attach
the plate to a wall stud.
[]Remove the fl'om the bolts.toggle wings
[]Insert the bolts into the mounting platethrough the holes designated to go into drywalland reattach the toggle wings to 3/4" (19 ram) ontoeach bolt.
To use toggle bolts:
MountingPlate,
Spacingfor TogglesMoreThanWall
÷l_.j_--ThicknessI
i ToggleWings
Bolt End
[]Place the nlounting plate against the wall andinsert the toggle wings into the holes in the wallto mount the plate.
NOTE: Before tightening toggle bolts and woodscrew, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushedflush against the wall and that the plate is properlycentered under the cabinet.
CAUTION: Be careful to avoid pinching fingersbetween the back of the mounting plate and the wall.
[]Tighten all bolts. Pull the plate away from the wallto hel t) tighten the bolts.
12
Installation Instructions
USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET
You need to drill holes for the top support screws, ahole large enough for the power cord to fit through,and a cutout large enough for the exhaust adaptor.
• Read the instructions on the TOP CABINETTEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on theTOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holesin the cabinet bottom.
CHECK FOR PROPERDAMPER OPERATION
BlowerPlate ExhaustAdaptor
X ___:-_ Damper
• Place the microwave in its upright position, with thetop of the unit facing up.
• Make sure tape securing damper is removed anddamper pivots easily before mounting microwave.
• You will need to make adjustments to assure properalignment with your house exhaust duct after themicrowave is installed.
I-_ MOUNT THE MICROWAVEOVEN
FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handleduring installation.
NOTE: If your cabinet is metal, use the nylongrommet around the power cord hole to preventcutting of the cord.
NOTE: We recommend using filler blocks if thecabinet fl'ont hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are
not used, case damage may occur fromovertightening screws.
NOTE: When mounting themicrowave oven, thread
power cord through hole inbottom of top cabinet. Kee t)it tight throughout Steps1-3. Do not pinch cord or
lift oven by pulling cord.[]Lift microwave, ittilt
forward, and hookslots at back bottom
edge onto four lowertabs of mounting[)late.
[]Rotate fl'ont of oven
up against cabinetbottom.
[]Insert a self-aligning screw through top centercabinet hole. Temporarily secure the oven byturning the screw at least two full turns after thethreads have engaged. (It will be completelytightened later.) Be sure to keep power cordtight. Be careful not to pinch the cord, especiallywhen mounting flush to bottom of cabinet.
13
Installation Instructions
I-_ MOUNT THE MICROWAVEOVEN (cont.)
Cabinet Front
Cabinet Bottom Shelf
Filler Block
-[Equivalentto Depthof CabinetRecess
Self-AligningScrew
MicrowaveOvenTop
[4_ Attach the microwave oven to the top cabinet.
[]Insert 2 self-aligning screws
through outer top cabinetholes. Turn two full turns oneach screw.
[] Tighten centerscrew completely.
[] Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.)
[]Install grease filters. See the Owner's Manualpacked with the microwave.
_-_ ADJUST THE EXHAUSTADAPTOR
Open the top cabilret alrd adjust the exhaust adaptorto connect to the house duct.
BackofBlowerPlate Damper Microwave
ForFront-to-BackorSide-to-SideAdjustment,Slide the ExhaustAdaptoras Needed
CONNECTING DUCTWORK
HouseDuct
[]Extend the house duct down to conl-lect tothe exhaust adaptor.
[]Seal exhaust duct joints using duct tape.
14
Installation Instructions
OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION OVERVIEW
B1. Prepare Rear WallB2. Remove Exhaust AdaptorBa. Attach Mounting Plate to WallB4. Prepare Top CabinetB5. Adjust BlowerB6. Mount tile Microwave Oven
IMPORTANT NOTES:
• Make sure tile screws for tile
blower motor and blower plateare securely tightened whenthey are reinstalled. This willhel t) to prevent excessivevibration.
• Make sure tile motor wiring hasbeen properly routed and secured,and that tile wires are not pinched.
[-_ PREPARING THE REAR WALLFOR OUTSIDE BACK EXHAUST
You need to cut an opening in tile rear wall foroutside exhaust.
• Read tile instructions on tile REARWALL TEMPLATE.
• Tape it to tile rear wall, lining up with tileholes previously drilled for holes A and B
in tile wall plate.
• Cut tile opening, following tile instructions of tileREAR WALL TEMPLATE.
I-_ REMOVE EXHAUST ADAPTOR
This microwave oven is shipped assembled for topexhaust. You will need tile exhaust adaptor forinstallation in tile rear wall opening. To removetile exhaust adaptor fl'om tile microwave oven:
[]Remove tape securing damper.
[] Raise damper flap. [] Slip tile damperB, r,, _ out of tile track
lower\Hate _ on tile blower' _ _ fi'ame by pressh-lg
[]Remove and save tile screw that holds tile blowerplate to tile microwave. Lift off tile blower plate.
Blower Plate
I o
_ _ _ BackofMicrowave
15
Installation Instructions
I-_ ATTACH THE MOUNTINGPLATE TO THE WALL
Attach the plate to the wall using toggle bolts.At least one wood screw must be used to attach
the plate to a wall stud.
[]Remove the toggle wings fl'om the bolts.
[]Insert the bolts into the mounting plate throughthe holes designated to go into drywall and reattachthe toggle wings to 3/4" (19 ram) onto each bolt.
To use toggle bolts:
MountingPlate
Spacingfor TogglesMore+l_,--,.[_Than Wall Thickness
toggleWings
Wa, !_
Bolt End
[]Place the mounting plate against the wall andinsert the toggle wings into the holes in the wallto mount the plate.
NOTE: Before tightening toggle bolts and woodscrew, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flushagainst the wall and that the plate is properlycentered under the cabinet.
CAUTION: Be careful to avoid pinching fingersbetween the back of the mounting plate and the wall.
[]Tighten all bolts. Pull the plate away fi'om the wallto hel t) tighten the bolts.
I-_ USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
• Read the instructions on the TOP CABINETTEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on theTOP CABINET TEMPLATE.
CAUTION: Weal" safety goggles when drilling holesin the cabinet bottom.
ADAPTING MICROWAVEBLOWER FOR OUTSIDEBACK EXHAUST
[] Remove and that holds blower motorsave screwto microwave.
BlowerMotorBackof
"" BlowerMotor"_ Screw
[] Carefully the blower unit. The wirespull out
will extend far enough to allow you to adjustthe blower ui°lit.
EndA
16
Installation Instructions
ADAPTING MICROWAVEBLOWER FOR OUTSIDE
BACK EXHAUST (cont.)
_ Rotate blower unit counterclockwise 180 °.
BeforeRotation After Rotation
Microwave Microwave
[]Gently tim wires fl'om tilerenlove grooves.Reroute the wires through grooves on other sideof the blower unit.
BeforeRerouting After Rerouting
Wires RoutedThroughRightSide Wires RoutedThroughLeft Side
[]Roll the blower unit 90 ° so that fan bladeopenings are facing out the back of thenlicrowave.
BeforeRolling
BackofMicrowave
After Rolling
Microwave
[]Place the blower unit back iirto the opening.
End
CAUTION: Do not pull or stretch the blowerunit wiring. Make sure the wires are notpinched, and that they are properly secured.
NOTE: The blower unit exhaust
openings should match exhaust
openings on rear of microwave oven.
] Secure tim blower unit to tim microwave withtim original screw.
2_,er Plate Backof
Microwave
[]Replace the blower [)late in the same positionas before with the screw. Make sure the screw
is tight.
[] Attach the exhaust adaptor to the rear of theoven by sliding it iirto the guides at the topcenter of the back of the oven.
Adaptor
BackofMicrowave
Guide
!ck,lgTabsGuide
Push in securely until it is in the lower lockingtabs. Take care to assure that the damper hingeis installed so that it is at the top and that thedamper swings fl'eely.
17
Installation Instructions
MOUNT THE MICROWAVEOVEN
FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN,
IMPORTANT: Do not grip or use handleduring installation,
NOTE: If your cabinet is metal, use the nylon
grommet around tile power cord hole to prevent
cutting of tile cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur fromovertightening screws.
NOTE: When mounting the
microwave oven, thread
power cord through hole in
bottom of top cabinet. Keep
it tight throughout Steps
1 3. Do not pinch cord or
lift oven by pulling cord.[]Lift microwave, ittilt
forward, and hook
slots at back bottom
edge onto four lower
tabs of mounting
[]Rotate fl'ont of oven
up against cabinetbottom.
[]Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven byturning the screw at least two full turns after thethreads have engaged. (It will be completelytightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especiallywhen mounting flush to bottom of cabinet.
CabinetFront
CabinetBottomShelf
FillerBlock
"_Equivalentto Depthof CabinetRecess
Self-AligningScrew
MicrowaveOvenTop
1_ Attach the microwave oven to the top cabinet.
[] hrsert 2 self-aligning screwsthrough outer top cabinetholes. Turn two full ttH'ns oneach screw.
[] Tighten center
screw completely.
[] Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.)
[]Install grease filters. See the Owner's Manualpacked with the microwave.
18
Installation Instructions
RECIRCULATING (Non-Vented Ductless)
INSTALLATION OVERVIEW
CI. Attach Mounting Plate to Wall
C2. Prepare Top CabinetC3. Check Microwave Assembly
C4. Adjust BlowerC5. Mount the Microwave Oven
C6. Install Charcoal Filter
IMPORTANT NOTES:
• Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routedand secured, and that the wires are not pinched.
I-_ ATTACH THE MOUNTINGPLATE TO THE WALL
Attach the plate to the wall using toggle bolts.At least one wood screw must be used to attach
the plate to a wall stud.
[]Remove the fi'om the bolts.toggle wings
[]Insert the bolts into the nlounting plate throughthe holes designated to go into drywall andreattach the toggle wings to 3/4" (19 ram) ontoeach bolt.
To use toggle bolts:
MountingPlate
Spacingfor TogglesMoreThanWall
_@_@,_Thicknessl ToggleWings
Bolt End
19
[]Place the mounting plate against the wall andinsert the toggle wings into the holes in the wallto mount the plate.
NOTE: Before tightening toggle bolts and woodscrew, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flushagainst the wall and that the plate is properlycentered under the cabinet.
CAUTION: Be careful to avoid pinching fingersbetween the back of the mounting plate and the wall.
[]Tighten all bolts. Pull the plate away fi'om the wallto hel t) tighten the bolts.
USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET
You need to drill holes for the top support screws anda hole large enough for the power cord to fit through.
• Read the instructions on the TOP CABINETTEMPLATE.
• Tape it underneath the top cabinet.
• Drill the holes, following the instructions on theTOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holesin the cabinet bottom.
Installation Instructions
[-_ CHECK MICROWAVE ASSEMBLY
Exhaust Adaptor
J J" i
Baokor-_v.-.-.-.-.-.-.-.-.-_--i_jl Microwave i....... q_
• Place the microwave in its upright position, with thetop of the unit facing up.
• The microwave oven may be shipped assembled fortop exhaust (adaptor installed) or for recirculationexhaust (adaptor absent).
• If the microwave was shipped for recirculationexhaust, remove the Exhaust Adaptor and proceedto C5. If the microwave was shipped for top exhaust,proceed to C4.
I-_ ADAPTING MICROWAVEBLOWER FOR RECIRCULATION
_ Remove tape securing dmnper.
[] Raise damper flap.
BlowerPlate
_Slip the damperout of the trackon the blower
and twistingboth ends.
Backof Microwave
_ Remove the that holds the blower platescrewto the microwave. Remove and save the screw
holding the blower motor to the microwave.
BlowerPlate
BackofMicrowave
NOTE: The blower plate will be reinstalled in a
later step. The damper is not needed for recirculatingmodels. Save any unused parts for possible future use.
[] Carefully pull out the blower unit. The wireswill extend fat" enough to allow you to adjustthe blower unit.
]Roll the blower unit 90 ° so that fan blade openingsare facing toward the fl'ont of the microwave.
R011
NOTE: Make sure wires remain routed in the
grooves of the motor fl'ame.
20
Installation Instructions
ADAPTING MICROWAVEBLOWER FORRECIRCULATION (cont.)
[]Place the blower unit back into the opening.
CAUTION: Do not pull or stretch the blower unitwiring. Make sure the wires are not pinched, andthat they are properly secured.
[]Secure blower unit to microwave with the screwremoved in Step 4. Make sure the screw is tight.
[]Replace blower plate with the screw removed inStep 1. Make sure the screw is tight.
gI
_ Backof
_ _- Microwave
MOUNT THE MICROWAVEOVEN
FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLEINSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handleduring installation.
NOTE: If your cabinet is metal, use the nylongrommet around the power cord hole to preventcutting of tile cord.
NOTE: We recommend using filler blocks if thecabinet front hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not used,
case damage may occur from overtighteningscrews.
NOTE: When mounting thenlicrowave oven, thread
power cord through hole inbottom of top cabinet. Kee t)it tight throughout Steps
1 3. Do not pinch cord orlift oven by pulling cord.
[]Lift microwave, tiltit forward, and hookslots at back bottom
edge onto four lowertabs of mountingplate.
[]Rotate fl'ont of oven
up against cabinetbottom.
[]Insert a self-aligning screw through top center
cabinet hole. Temporarily secure the oven byturning the screw at least two full turns after the
threads have engaged. (It will be completelytightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especiallywhen mounting flush to bottom of cabinet.
Cabinet Front
Cabinet Bottom Shelf
Filler Block
Equivalentto Depth
of CabinetRecess
Self-AligningScrew
MicrowaveOvenTop
[]Attach the microwave oven to the top cabinet.
21
Installation Instructions
MOUNT THE MICROWAVEOVEN (cont.)
[]Insert 2 self-aligning screwsthrough outer top cabinetholes. Turn two full turns on
each screw.
I
[] Tighten centerscrew completely.
[] Tighten the outer two screws to the top of the
microwave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.)
_ Install grease filters. See the Owner's Manualpacked with the microwave.
INSTALLING THECHARCOAL FILTER
NOTE: The charcoal filter is factory installed inrecirculating models. Follow these steps to replace a
filter or to install a filter after converting a ventedmodel to recirculating operation.
[]Remove screws on fi'ont of grille using a#1 Phillips screwdriver.
_Open the door.
[]Remove the grille.
Pull the grille straight off.CharcoalFilter
[] hrstall the charcoal filter. When properly installed,the wire mesh of the filter should be visible fromthe fl'ont.
[Replace the grille and the screws.
[]Close the door.
Insertmesh-sideup
22
Installation Instructions
BEFORE YOU USE YOUR MICROWAVE
-_ Make sure the microwave oven has beeninstalled according to instructions. F_ Read tile Owner's Manual.
I
F_ emove all packing material fl'om thelllicrowave ovel-l.
F37] Install turntable and ring in cavity.
F_ Replace house fuse or turn breaker back on.
I
F_ KEEP INSTALLATION INSTRUCTIONSFOR THE LOCAL INSPECTOR'SUSE.
Plug power cord into a dedicated 15- to 20-ampelectrical outlet.
Ensure properground exists/before use
23