installation parking sensors 2020 rdx …...parking sensor harness ground terminal vehicle ground...
TRANSCRIPT
© 2019 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
PARKING SENSORS
served. BII11735-26 (190
2020 RDX
4) 0
Issue Date
APR 2019
PARTS LIST
Parking Sensors Attachment KitP/N 08V67-TJB-200
Parking sensor harness
Subharness
Front bumper harness
Rear bumper harness
Control unit
Control unit bracket
Switch
14 Wire ties(1 Not used)
2 Retainers A(round)
2 Retainers B(flat)
2 Alcohol wipes
Flange nut
1 of 278V67-TJB-2000-90
Urethane tape
Clip
Sensors KitP/N 08V67-TJB-200J
4 Front sensors
2 Rear sensors A
2 Rear sensors B
2 of 27 BII11735-2
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Small flat-tip screwdriver
10 mm Open end wrench
10 mm Socket
Pushpin
Ratchet
3 mm, 6 mm, and 8.5 mm Drill bits
Eye protection (face shield, safety goggles, etc.)
File
Masking tape
5 mm Hex wrench
Blanket
Shop towel
Drill
Diagonal cutters
Rubber mallet
The following tools are available through the Acura Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
• 16 mm Punch Tool (T/N 07AAH-TZ5A100)
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
Illustration of the Parking Sensors on the Vehicle
SWITCH SUBHARNESS
FRONT BUMPER HARNESS
2 FRONT SENSORS
2 FRONT SENSORS
2 REAR SENSORS B
2 REAR SENSORS A
CONTROL UNIT
PARKING SENSOR HARNESS
REAR BUMPER HARNESS
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
INSTALLATION
Client Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE: If installing the fog lights kit, install the parking sensors kit first.
1. Disconnect the negative cable from the battery.
2. Pull away the door opening seal, and remove the driver’s dashboard side lid.
DRIVER’S DASHBOARD SIDE LID
5 CLIPS DOOR OPENING SEAL(Pull away.)
6 (1904) 3 of 27
3. Remove the driver’s dashboard side vent.
DRIVER’S DASHBOARD SIDE VENT
4 CLIPS
4. Remove the left trim, and unplug the vehicle connector.
VEHICLE CONNECTOR
9 CLIPSLEFT TRIM
4 of 27 BII11735-2
5. Remove the driver’s dashboard lower cover, and unplug the vehicle connectors and vehicle sensor.
VEHICLE SENSOROPPOSITE
SIDE VIEW
DRIVER’S DASHBOARD LOWER COVER(inside)
2 SELF-TAPPING SCREWS
2 RETAINING TABS
DRIVER’S DASHBOARD LOWER COVER13 CLIPS
VEHICLE CONNECTORS
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
6. Release and pull up on the rear seat cushion.NOTE: Place a piece of masking tape as shown to prevent the hook from engaging.
5 RETAINING TABS
2 CLIPS
LEFT REAR DOOR SILL TRIM
Squeeze. HOOK1
Pull.2
HOLEMASKING TAPE
REAR SEAT CUSHION
7. Remove the left rear door sill trim.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
8. Remove the cargo floor board.
5 CLIPS
CARGO FLOOR BOARD
LEVER
6 (1904) 5 of 27
9. Remove the four tie-down hooks.
8 RETAINING TABS
4 TIE-DOWN HOOKS
4 TIE-DOWN HOOKS 4 SCREWS
4 COVERS(Open.)
10. Remove the left and right cargo strips.
2 CLIPS
LEFT CARGO STRIP
RIGHT CARGO STRIP
2 CLIPS
6 of 27 BII11735-2
11. Remove the cargo bin.
5 CLIPS
3 RETAINING TABS
CARGO BIN
12. Remove the rear panel lining.
4 RETAINING TABS 4 CLIPS
REAR PANEL LINING
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
13. Remove the two bolts. Loosen the bolt, and turn the left bracket as shown.
2 BOLTS
BOLT(Loosen.)
LEFT BRACKETLEFT BRACKET(Turn 90°.)
14. Fold down the left rear seat-back.
LEFT REAR SEAT-BACK(Fold down.)
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
15. Gently pull the inner handle on the left rear side trim panel, and use a small flat-tip screwdriver wrapped with a shop towel to remove the inner handle cap.
LEFT REAR SIDE TRIM PANEL
INNER HANDLE CAP
2 SCREWS
SMALL FLAT-TIP SCREW-DRIVER
INNER HANDLE CAP
SHOP TOWEL
INNER HANDLE(Pull.)
2 RETAINING TABS
SECTION VIEW
16. Remove the two screws from the left rear side trim panel.
6 (1904) 7 of 27
17. Pull away the door opening seal and weatherstrip from around the left rear side trim panel. Remove the trim panel.
WEATHERSTRIP(Pull away.)
9 RETAIN-ING TABS
DOOR OPENING SEAL(Pull away.)
FLANGE NUT
6 CLIPS BOLT
LEFT REAR SIDE TRIM PANEL
18. Release the cable from the left rear side trim panel, then remove the inner handle.
LEFT REAR SIDE TRIM PANEL(inside)
2 CLIPS
CABLE INNER HANDLE
4 RETAINING TABS
8 of 27 BII11735-2
19. Pull away the door opening seal and weatherstrip from around the left quarter pillar trim.
VEHICLE PANEL
LEFT QUARTER PILLAR TRIM
CLIP
VEHICLE PANEL
Strike perpendicular to the vehicle.
CLIP
SHOP TOWEL
RUBBER MALLET
LEFT QUARTER PILLAR TRIM
DOOR OPENING SEAL(Pull away.)
WEATHERSTRIP(Pull away.)
CLIP
SECTION VIEW
20. Using a rubber mallet wrapped with a shop towel, lightly tap the area marked SIDE CURTAIN AIRBAG on the left quarter pillar trim to push in the clip.NOTE: Make sure to strike the area perpendicular to the vehicle.
21. Remove the left quarter pillar trim.
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
LEFT QUARTER PILLAR TRIM
5 CLIPS3 RETAINING TABS
22. Wrap a shop towel around the hood latch.
HOOD LATCH(Wrap with a shop towel.)
23. Remove the front bulkhead cover.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
FRONT BULKHEAD COVER
8 CLIPS
24. Remove the front bumper.
• Apply masking tape as shown.
HEADLIGHT FRONT FENDER
FRONT BUMPER
MASKING TAPE
6 (1904) 9 of 27
• Remove the two self-tapping screws (long), two self-tapping screws, six clips (long), six clips, four clips (short), five bolts (short), and two bolts as shown.
2 SELF-TAPPING SCREWS(long)
6 CLIPS
2 SELF-TAPPING SCREWS
5 BOLTS(short)
CLIP(long)
BOLT4 CLIPS(short)
BOLT
CLIP(long)
BOTTOM VIEW
BOLT(short)
BOLT BOLT BOLT(short)
SELF-TAPPING SCREWSELF-
TAPPING SCREW
CLIP(long)
3 BOLTS(short)
4 CLIPS(short)
CLIP(long)
4 CLIPS(long)
10 of 27 BII11735-2
• With the help of an assistant, release the six retaining tabs on each side.
3 RETAINING TABS
FRONT BUMPER
FRONT BUMPER
FRONT BUMPER
3 RETAINING TABS
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
• With the help of an assistant, remove the front bumper and unplug the vehicle connector.
• Place the front bumper on a blanket.
VEHICLE CONNECTOR
FRONT BUMPER
2 CLIPS
OPPOSITE SIDE VIEW
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
25. Remove the two covers.
SLOTPLASTIC TRIM TOOL
4 RETAINING TABS
2 COVERS
6 (1904) 11 of 27
26. Remove the rear bumper.
• Apply masking tape as shown.
TAILLIGHT
REAR FENDER
MASKING TAPE
REAR BUMPER
12 of 27 BII11735-2
• Remove the two flange bolts, two hex bolts, eight self-tapping screws, and two clips as shown.
2 HEX BOLTS
2 FLANGE BOLTS
8 SELF TAPPING SCREWS
2 CLIPS
• With the help of an assistant, release the seven retaining tabs on each side.
7 RETAINING TABS
REAR BUMPER
REAR BUMPER
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
• With the help of an assistant, remove the rear bumper.
• Place the rear bumper on a blanket.
REAR BUMPER
4 RETAINING TABS
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
27. Release the vehicle 12-pin connectors from the vehicle connectors.
VEHICLE CONNECTORS
VEHICLE 12-PIN CONNECTORS
TAPE(Remove.)
PARKING SENSOR HARNESS 12-PIN CONNECTOR
VEHICLE 12-PIN CONNECTORS
LEFT REAR SIDE TRIM PANEL OPENING
PARKING SENSOR HARNESS
28. Route the parking sensor harness up along the vehicle harness, and remove the tape to free the parking sensor harness 12-pin connector.
29. Unplug the vehicle 12-pin connector, and plug it into the parking sensor harness 12-pin connector.
6 (1904) 13 of 27
30. Plug the vehicle 12-pin connector into the parking sensor harness 12-pin connector. Secure the 12-pin connectors to the vehicle connectors as shown.
PARKING SENSOR HARNESS 12-PIN CONNECTOR
VEHICLE CONNECTORS
12-PIN CONNECTORS
VEHICLE 12-PIN CONNECTORS
LEFT REAR SIDE TRIM PANEL OPENING
PARKING SENSOR HARNESS
VEHICLE HARNESS
3 WIRE TIES
12-PIN CONNECTORS
31. Secure the parking sensor harness and 12-pin connectors to the vehicle harness with three wire ties.
14 of 27 BII11735-2
32. Install the control unit bracket to the control unit.
CONTROL UNIT BRACKET
CONTROL UNIT
33. Install the control unit to the vehicle panel with one flange nut as shown.
CONTROL UNIT BRACKET
FLANGE NUT
VEHICLE BOLT
VEHICLE PANEL
HOLE
CONTROL UNIT BRACKET
LEFT REAR SIDE TRIM PANEL OPENING
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
34. Plug the parking sensor harness 16-pin connector into the control unit.
CONTROL UNIT
PARKING SENSOR HARNESS 16-PIN CONNECTOR
LEFT REAR SIDE TRIM PANEL OPENING
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
35. Plug the parking sensor harness 8-pin connector into the vehicle 8-pin connector.
LEFT REAR SIDE TRIM PANEL OPENING
PARKING SENSOR HARNESS 8-PIN CONNECTOR
VEHICLE 8-PIN CONNECTOR
PARKING SENSOR HARNESS
6 (1904) 15 of 27
36. Remove the vehicle clip.
VEHICLE CLIP
INSULATOR
LEFT REAR SIDE TRIM PANEL OPENING
37. Peel back the insulator, and remove the vehicle grommet. Route the parking sensor harness through the vehicle panel hole as shown.
INSULATOR(Peel back.)
VEHICLE GROMMET(Do not reuse.)
LEFT REAR SIDE TRIM PANEL OPENING
PARKING SENSOR HARNESS
16 of 27 BII11735-2
38. Secure the grommet on the parking sensor harness to the vehicle panel hole.NOTE:
• While holding the grommet carefully insert it into the vehicle panel hole, and make sure it is seated properly.
• Do not pull on the socket or harness when installing the grommet.
VEHICLE PANEL HOLE
SECTION VIEW
VEHICLE PANEL
GROMMET ON THE PARKING SENSOR HARNESS
GROMMET ON THE PARKING SENSOR HARNESS
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
39. Remove the vehicle ground bolt, and secure the parking sensor harness ground terminal using that bolt.NOTE: Do not put the ground terminal calkings on top of one another.
VEHICLE GROUND TERMINALS
PARKING SENSOR HARNESS GROUND TERMINAL
VEHICLE GROUND BOLT
LEFT REAR SIDE TRIM PANEL OPENING
PARKING SENSOR HARNESS
VEHICLE HARNESS
5 WIRE TIES
40. Secure the parking sensor harness to the vehicle harness with five wire ties.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
41. Route the parking sensor harness along the vehicle harness, and secure it to the vehicle harness with four wire ties.
VEHICLE HARNESSPARKING SENSOR
HARNESS
4 WIRE TIES
6 (1904) 17 of 27
42. Using a pushpin, pierce the rear bumper at the center of the four scribe marks. NOTE: Make sure to pierce perpendicular to the rear bumper.
: 2 MARKS
2 SCRIBE MARKS
PUSHPIN(Pierce perpendicular.)
REAR BUMPER
PUSHPIN(Pierce perpendicular.)
REAR BUMPER
2 SCRIBE MARKS
: 2 MARKS
REAR BUMPER(inside)
18 of 27 BII11735-2
43. While wearing eye protection, drill the four pierced marks to 8.5 mm from the inside of the rear bumper.
• First, drill with a 3 mm drill bit, then follow with a 6 mm drill bit, and finish with an 8.5 mm drill bit.NOTE: Make sure to drill perpendicular to the rear bumper.
REAR BUMPER(inside)
DRILL(Drill perpendicular.)
REAR BUMPER
3 mm 6 mm 8.5 mm DRILL BITS
: 4 MARKS
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
44. Using a 16 mm punch tool, punch out the four rear bumper holes as shown.NOTE: Make sure to hold the punch perpendicular to the rear bumper. Remove any burrs.
OPEN END WRENCH
4 HOLES
REAR BUMPER(inside)
SECTION VIEW
REAR BUMPER
OUTSIDE INSIDE
16 mmPUNCH TOOL(MALE)
16 mmPUNCH TOOL(FEMALE)
16 mmPUNCH TOOL(MALE)
16 mm PUNCH TOOL(FEMALE)
Clockwise. Counterclockwise.
Punch out.
Punch out.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
45. Using the two alcohol wipes, thoroughly clean the rear bumper where the two retainers A (round) and two retainers B (flat) will attach.
REAR BUMPER(inside)
Clean with the alcohol wipe.
ALCOHOL WIPE
Clean with the alcohol wipe.
ALCOHOL WIPE
ALCOHOL WIPE
ADHESIVE BACKING(Remove.)
Clean with the alcohol wipe.
ADHESIVE BACKING(Remove.)
RETAINER A(round)
RETAINER A(round)
ADHESIVE BACKING(Remove.)
ADHESIVE BACKING(Remove.)
Clean with the alcohol wipe.
RETAINER B(flat)
RETAINER B(flat)MARK
SCRIBE MARK
MARK
ALCOHOL WIPE
MARK
MARK
SCRIBE MARK
MARK
MARKSCRIBE MARK MARK
MARK
SCRIBE MARK
46. Remove the four adhesive backings from the two retainers A (round) and two retainers B (flat), and attach the two retainers A (round) and two retainers B (flat) to the rear bumper as shown.NOTE: Make sure the retainers are attached in the proper orientation.
6 (1904) 19 of 27
47. Install the two rear sensors A and two rear sensors B to the two retainers A and two retainers B.NOTE: Make sure to install the sensors in the correct position.
RETAINER A RETAINER A
2 RETAINING TABS
REAR SENSOR A
2 RETAINING TABS
REAR SENSOR B
RETAINER B
RETAINER B
REAR SENSOR A
2 RETAINING TABS
2 RETAINING TABS
REAR SENSOR B
REAR BUMPER(inside)
20 of 27 BII11735-2
48. Plug the four rear bumper harness 6-pin connectors into the two rear sensors A and two rear sensors B.
REAR BUMPER HARNESS4 REAR BUMPER
HARNESS 6-PIN CONNECTORS
2 REAR SENSORS B
2 REAR SENSORS A REAR
BUMPER(inside)
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
49. Secure the rear bumper harness to the two rear sensors A and two rear sensors B with four clips on the rear bumper harness as shown.
4 CLIPS ON THE REAR BUMPER HARNESS
2 REAR SENSORS A AND 2 REAR SENSORS B
REAR BUMPER HARNESS
3 CLIPS ON THE REAR BUMPER HARNESS
RIBS
REAR BUMPER(inside)
50. Secure the rear bumper harness to the ribs on the rear bumper with the three clips on the rear bumper harness as shown.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
51. With the help of an assistant, bring the rear bumper close to the vehicle, and plug the rear bumper harness 4-pin connector into the parking sensor harness 4-pin connector.
PARKING SENSOR HARNESS 4-PIN CONNECTOR
REAR BUMPER HARNESS 4-PIN CONNECTOR REAR BUMPER
CONNECTOR LOCK(Do not cover.)
URETHANE TAPE
4-PIN CONNECTORS
52. Wrap the urethane tape around the 4-pin connectors as shown. Install the rear bumper.
6 (1904) 21 of 27
53. Release the vehicle harness from the front bumper as shown. Unplug the vehicle connector.
VEHICLE HARNESS(Do not reuse.)
FRONT BUMPER (inside)
4 VEHICLE CLIPS
VEHICLE CONNECTOR
AMBIENT SENSOR
HOLDERS
VEHICLE HARNESS
22 of 27 BII11735-2
54. Remove the four caps from the four vehicle brackets.
8 RETAINING TABS
4 CAPS
4 CAPS(Do not reuse.)
FRONT BUMPER(inside)
4 VEHICLE BRACKETS
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
55. Install the four front sensors to the four vehicle brackets.
2 RETAINING TABS
FRONT SENSOR
VEHICLE BRACKET
2 RETAINING TABS
VEHICLE BRACKETFRONT
SENSOR
FRONT BUMPER(inside)
2 RETAINING TABS
VEHICLE BRACKET
FRONT SENSOR
VEHICLE BRACKET
FRONT SENSOR
2 RETAINING TABS
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
56. Plug the front bumper harness 2-pin connector into the ambient sensor.
AMBIENT SENSOR
FRONT BUMPER HARNESS 2-PIN CONNECTOR
4 FRONT SENSORS
FRONT BUMPER HARNESS4 FRONT BUMPER
HARNESS 6-PIN CONNECTORS
FRONT BUMPER(inside)
57. Plug the four front bumper harness 6-pin connectors into the four front sensors as shown.
6 (1904) 23 of 27
58. Secure the front bumper harness to the front bumper with the eight clips on the front bumper harness as shown.
4 CLIPS ON THE FRONT BUMPER HARNESS
FRONT BUMPER(inside)
FRONT BUMPER HARNESS
4 CLIPS ON THE FRONT BUMPER HARNESS
24 of 27 BII11735-2
59. Secure the front bumper harness to the front bumper with the seven holders as shown.
FRONT BUMPER(inside)
FRONT BUMPER HARNESS
7 HOLDERS
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
60. With the help of an assistant, bring the front bumper close to the vehicle, and plug the front bumper harness 12-pin connector into the vehicle 12-pin connector as shown. Install the front bumper.
VEHICLE 12-PIN CONNECTORFRONT BUMPER
HARNESS 12-PIN CONNECTOR
FRONT BUMPER
61. Plug the subharness 4-pin connector into the vehicle 4-pin connector.
SUBHARNESS 4-PIN CONNECTOR
SUBHARNESS
DRIVER’S DASHBOARD LOWER COVER OPENING
VEHICLE 4-PIN CONNECTOR
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
62. Plug the subharness 4-pin connector into the vehicle 4-pin connector.
SUBHARNESS
SUBHARNESS 4-PIN CONNECTOR
VEHICLE 4-PIN CONNECTOR
DRIVER’S DASHBOARD LOWER COVER OPENING
63. Remove the vehicle switch from the driver’s dashboard lower cover.
2 RETAINING TABS
SWITCH
VEHICLE SWITCH(Do not reuse.)
2 RETAINING TABS
DRIVER’S DASHBOARD LOWER COVER
64. Install the switch to the driver’s dashboard lower cover.
6 (1904) 25 of 27
65. Plug the subharness 8-pin connector into the switch. Install the driver’s dashboard lower cover.
DRIVER’S DASHBOARD LOWER COVER
SWITCHSUBHARNESS 8-PIN CONNECTOR
26 of 27 BII11735-2
66. Remove the vehicle clip, and install the clip to the left quarter pillar trim.
LEFT QUARTER PILLAR TRIM
CLIP(supplied)
VEHICLE CLIP(Do not reuse.)
LEFT QUARTER PILLAR TRIM
67. Check the overlap between the headliner and the left quarter pillar trim. NOTE: Check and adjust the overlap as described in the service information.
68. Install the left quarter pillar trim. NOTE:
• Make sure the side curtain airbag is not tucked under the clip.
• Do not push the left quarter pillar trim excessively.
6 (1904) © 2019 American Honda Motor Co., Inc. – All Rights Reserved.
69. Check that all wire harnesses are routed properly and that all connectors are plugged in.
70. Install all removed parts.
71. Connect the negative cable to the battery.
72. Press and hold the audio unit power button for 2 seconds to restore the audio and navi (if equipped) system functions.
73. Set the clock on vehicles without navigation.
74. If necessary, restore the systems back to normal operation as described in the service information.
Check the Operation of the Parking Sensors
75. Make sure the parking sensors work properly as described in the online owner’s manual.
© 2019 American Honda Motor Co., Inc. – All Rights Reserved. BII11735-2
6 (1904) 27 of 27