installation time squ are instructions deck-mount bath...
TRANSCRIPT
Certified to comply with ANSI A112.18.1M
ROUGHING-INDIMENSIONS
Required Tools
Wrench(Supplied)
Turn off hot and cold watersupplies before beginning.CAUTION1 2
Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.Make sure that the RUBBER RING (2) is properly seated in RECESSat base of SPOUT (3).Assemble RUBBER WASHER (4) and BRASS WASHER (5) ontoSHANK (1). From underside of ledge secure SPOUT (3) into positionwith LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
Prepare TUBE and TEE ASSEMBLY (1) to fit center to centerVALVE (2) location (between 6-1/2" and12"). If necessary,cut and/or bend TUBING carefully. Make sure tube bend isclose to the TEE (1) so that it will not effect the compressionjoint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from eachVALVE (2) and slide onto TUBING (5).
Adjustable Wrench
Channel Locks
7184.9007184.901
Flat Blade Screwdriver
VALVE inlet is 3/4-inchNPT male connector.
NOTE
2
ADJ. 6-1/2 TO 12
43
1
34
5
RECESS
3
1
2
4
6
5
MOUNTINGSURFACE.
MOUNTINGSURFACE
10-1/4"(262mm)
6-3/4"(172mm)
3-3/4"(97mm)
4"(102mm)
11-1/4"(287mm)
Phillips Screwdriver
DECK-MOUNT BATH FILLER
InstallationInstructions
Thank you for selecting American-Standard...the benchmarkof fine quality for over 100 years.
To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.
6-1/2" to 12"(165mm to 305mm)
14-3/4" (377mm)
1-1/2 MAX.(38mm) MAX.1-3/16" MAX.
(30mm) MAX.
1-3/16 D.(30mm) D.
3'(76mm)
(H) (C)
1-1/8 D.
12 MAX.(305mm)
1-1/16 D.(27mm) D.
3/4-14 MALEN.P.T. INLETS
M965466 Rev. 1.2
TIME SQUARE™
10
3
55/16'' MIN. MOUNTING SURFACE
11
11
10
11
1
3Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)into mounting holes from underside of ledge.
Install LOCKNUTS (1) and RUBBER WASHERS (3) onto valve shanks.
Place RUBBER RING (11) into DECK ADAPTERS (10) and thread ontovalves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (5) position.
Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tightenCOUPLING NUT (14) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet ofright VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
13
5
14
8
7
99a
6
14
134 5
10
MOUNTINGLEDGE
DECKADAPTER
4 INSTALL HANDLES
Turn VALVE to OFF position.
Push ADAPTER (1) on VALVE STEM (2), so that the hole of theADAPTER (1) without a spline is facing up. Fig. A. TightenSTEM SCREW (3) to secure ADAPTER (1).
Align male teeth on DECK ADAPTER (5) to female teeth in LEVER HANDLEASSEMBLY (4). Push LEVER HANDLE ASSEMBLY (4) onto DECKADAPTER (5) flush against mounting surface.
Tighten SET SCREW (6) with HEX WRENCH supplied to secureLEVER HANDLE ASSEMBLY (4). View A.
FOR FITTINGLESS SPRAY
Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) isproperly seated on SHANK (7). Push COUPLING (9 or 9a) into TEE (6) andattach to SPOUT SHANK (7) and tighten. Note: For product with HandShower, COUPLING (9) is tightened using a 10mm (3/8”)Hex Wrench.
1
23
5
6
4
TOP
MALE TEETHSPLINE END DOWN
Fig. A.
View. A.
FEMALE TEETH
View. A.
HEX WENCHSUPPLIED
M965466 Rev. 1.2
8To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.Loosen SET SCREW (1) and pull ofHANDLE ASSEMBLY (2). Loosen HANDLE SCREW (3) and pull offHANDLE ADAPTER (4).Remove SPRING CLIP (5).Lift STOP WASHER (6), turn 90° and replace.Replace SPRING CLIP (5).Refer to step four for HANDLE ASSEMBLY (2)instructions.
If spout drips, operate handles several timesfrom OFF to ON position. Do not force - handlesturn only 90°.
SERVICE 9
HANDSHOWER INSTALLATION (Model 7184.901 series only)
TEST INSTALLED FAUCET6Turn VALVES "off" and attach handles.
Lift HANDSHOWER from HOLDER, direct spray into tub, liftTRANSFER KNOB to check HANDSHOWER and HOSES for leaks.Turn handles "off."
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max fromSPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) BRASS WASHER (4) and LOCKNUT from underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT.
Add SEAL WASHER (5) and connect HOSE (10) to outlet nippleat the bottom of COUPLING (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAYESCUTCHEON (1). Install SEAL (9) and connect both HOSES (8)and (10), Connect HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated in the HOLDER.
NOTE
5
With handles in "off" position, turn on water supplies and checkall connections for leaks.Operate both handles and flush water lines thoroughly.Check SPOUT mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minuteat higher water pressure. Do not fill bathtub unattended.
CAUTION
12
34
57
810
9
911
6
LOCKNUT
DO: SIMPLY RINSE THE PRODUCTCLEAN WITH CLEAR WATER.DRYWITH A SOFT COTTON FLANNELCLOTH.
DO NOT: DO NOT CLEAN THEPRODUCT WITH SOAPS, ACID,POLISH, ABRASIVES, HARSHCLEANERS, OR A CLOTH WITHA COARSE SURFACE.
CARE INSTRUCTIONS:
1
2
3
4
5
6
HEX WENCHSUPPLIED
Hex wench(supplied)
Before the bathroom is completely finished, you may want to remove spout, handshower, and handles to avoid damage during construction.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Unthread LIFT ROD KNOB (2) and remove.
Remove PLUG BUTTON (3) and remove SET SCREW (4) using
Lift SPOUT (1) off SHANK (5) carefully and remove RUBBERRING (6).Unthread SHANK SLEEVE (7) and remove from SHANK (5).
Reverse sequence to re-install SPOUT (1). Be sure RUBBERRING (6) is properly seated in its recess at the base of theSPOUT (1). Make certain SET SCREW (4) is properly alignedand tight so that SPOUT (1) is locked in place.
1
8
2
34
6
5
7
VIEW "A"
VIEW "A"
7
90°
M965466 Rev. 1.2
918049-0070AHANDLE ADAPTER
M962849-0070ASTREAM STRAIGHTENER
028679-0070ATUBE & TEEASSEMBLY
012668-0070ASHANK KIT
030274-0070ASHANK
MOUNTING KIT
A912629-0070ARUBBER RING
M917161-0070ASET SCREW
012078-0070AVALVE COUPLING KIT
M964421-YYY0AHAND SHOWER
HOLDER
028699-0070ACOUPLING (FOR TRANSFER)
030275-0070ASHANK SLEEVE KIT
030278-0070ATRANSFERSEAL KIT
M964423-YYY0ASPOUT KIT (7184.900)
M964437-YYY0ASPOUT KIT (7184.901)
MODEL NUMBER
7184.900 / 7184.901
028698-0070ACOUPLING(LESS SPRAY)
M952454-0070ATRANSFER
ROD ASSEMBLY
DECK-MOUNT BATH FILLER
CHROMESATIN NICKEL
002295
Replace the "YYY" withappropriate finish code
M950332-YYY0AHAND SHOWER
M961634-0070AVALVE MTG. KIT
994053-0070ACARTRIDGE
M964417-0070ADECK ADAPTER KIT
M964416-YYY0ALEVER HANDLEASSEMBLY
918555-0070AHANDLE SCREW
M962575-YYY0ATRANSFER LIFT KNOB
For toll-free information and answers to your questions, call:1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. ESTIN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. ESTIN MEXICO 01-800-839-1200
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .© A S A m e r i c a , I n c . 2 0 1 3
HOT LINE FOR HELP
M918075-0070ASET SCREW
028667-0020AHAND SHOWER HOSE
A952849-0070ACHECK VALVE
051343-0070AHOSE KIT
TIME SQUARE™
M965466 Rev. 1.2